k-pos follow target mode
Post on 06-Jul-2018
236 Views
Preview:
TRANSCRIPT
-
8/17/2019 K-Pos Follow Target Mode
1/16
Kongsberg K-PosFollow Target Mode
Operator Manual Release 7.0
301040/A
October 2006
-
8/17/2019 K-Pos Follow Target Mode
2/16
Document history
Document number: 301040
Rev. A October 2006 This version describes operation of the Follow Target mode of
the K-Pos system at K-Pos basis software release 7.0.
The reader
This operator manual is intended as a reference manual for the system operator. This manual is based onthe assumption that the system operator is an experienced DP operator with a good understanding of basicDP principles and general DP operation. If this is not the case, then the operator should first attend theappropriate Kongsberg Maritime training courses.
Note
The information contained in this document remains the sole property of Kongsberg Maritime AS. No part of this document may be copied or reproduced in any form or by any means, and the informationcontained within it is not to be communicated to a third party, without the prior written consent of
Kongsberg Maritime AS. Kongsberg Maritime AS endeavours to ensure that all information in this document is correct and fairly stated, but does not accept liability for any errors or omissions.
Warning
The equipment to which this manual applies must only be used for th e purpose for which it wasdesigned. Improper use or maintenance may cause damage to the equipment and/or injury to personnel.The user must be familiar with the contents of the appropriate manuals before attempting to operateor work on the equipment.
Kongsberg Maritime disclaims any responsibility for damage or injury caused by improper installation,use or maintenance of the equipment.
Comments
To assist us in making improvements to the product and to this manual, we welcome comments andconstructive criticism.e-mail: km.documentation@kongsberg.com
P.O.Box 483N-3601 Kongsberg,
Norway
Kongsberg Maritime AS
Telephone: +47 32 28 50 00Telefax: +47 32 28 50 10
Service: +47 815 35 355
www.kongsberg.com
-
8/17/2019 K-Pos Follow Target Mode
3/16
Operator Manual
Table of contents
1 FOLLOW TARGET MODE .................................................... 5
2 FOLLOW SINGLE MOBILE TARGET..................................... 7
3 MULTI TARGETING............................................................ 7
4 ENTERING FOLLOW TARGET MODE ................................. 10
5 CORRUPTED TRANSPONDER SIGNALS ............................ 13
6 HEADING CONTROL ........................................................ 13
7 POSITION CONTROL ....................................................... 13
8 SPEED CONTROL ............................................................. 139 ACCELERATION............................................................... 14
10 RATE OF TURN ................................................................ 14
301040/A 3
-
8/17/2019 K-Pos Follow Target Mode
4/16
Follow Target Mode
4 301040/A
-
8/17/2019 K-Pos Follow Target Mode
5/16
Operator Manual
1 FOLLOW TARGET MODEA K-Pos system with Follow Target mode has one of twoavailable configurations:
• Follow Single Mobile Target
• Follow Multiple Mobile Targets
Follow Single Mobile Target enables the vessel to automaticallyfollow a moving target and keeps the vessel within a “positionwindow” relative to the target. The moving target must beequipped with a mobile reference transponder or laser reflector in order for the K-Pos system to monitor its relative position. If,for example, the moving target is a Remotely Operated Vehicle,
then the vessel must be equipped with a Hydroacoustic PositionReference (HPR) system.
In addition to a mobile reference transponder on the target, anadditional fixed position-reference system is required, such asDGPS or a fixed transponder deployed on the seabed.
You can define a circle of operation within which the target canmove without causing the vessel to move. The vessel only moveswhen the target reaches the boundary of this circle. The radius of this circle (the “reaction radius”) can be up to 1000 m.
301040/A 5
-
8/17/2019 K-Pos Follow Target Mode
6/16
Follow Target Mode
Figure 1 Follow Single Target
Follow Multiple Mobile Targets enables a DP vessel to follow amoving structure or vessel equipped with two or more targets(such as laser reflectors). For example, a Fanbeam positionreference system with software for dual target can typically beused. The moving structure can be followed both with respectto position and heading.
The operator can select between the following operational modes:
• Follow Position, makes the vessel follow the moving structurewith respect to position. The vessel will always have the same
position relative to the moving structure, while maintainingthe absolute heading.
• Follow Heading , makes the vessel follow the moving structurewith respect to heading. The vessel will always have the sameheading relative to the moving structure, while maintainingthe absolute position.
• Follow Position and Heading , makes the vessel follow themoving structure with respect to both position and heading.
The vessel will always have the same position and headingrelative to the moving structure.
6 301040/A
-
8/17/2019 K-Pos Follow Target Mode
7/16
Operator Manual
2 FOLLOW SINGLE MOBILE TARGETThis section describes the Follow Target dialog box in a K-Possystem that has the Follow Single Mobile Target configuration.
To display the Follow Target dialog box, click AutoPos→FollowTarget.
Mobile Targets
To select a transponder, in the Available list, highlight the requiredtransponder and click Add. To remove a transponder from theSelected list, highlight the transponder you want to remove andclick Rem. Only one transponder can be selected at a time.
Reaction Limits
Position
Defines the reaction limit for position (reaction circle). The valueentered (between 0 and 1000 m) is the radius of the reactioncircle for the mobile target.
Position Filter
Filter constant
Enter the required filter constant (0 to 100%) to increase or decrease the degree of position filtering. A high percentage (50to 100%) gives a high filtering which is recommended if there isnoise or unstable measurements from the transponders. A low
percentage (0 to 50%) gives a low filtering which should be usedif measurements from the transponders are stable and reliable.
3 MULTI TARGETING
This section describes the Follow Target dialog box in a K-Possystem that has the Follow Multiple Mobile Targets configuration.
301040/A 7
-
8/17/2019 K-Pos Follow Target Mode
8/16
Follow Target Mode
To display the Follow Target dialog box, select AutoPos→FollowTarget
Mobile Targets
To select a transponder, in the Available list, highlight the requiredtransponder and click Add. To remove a transponder from theSelected list, highlight the transponder you want to remove andclick Rem.
Operation mode
Follow Position
Choose this to make the vessel follow the moving structure
with respect to position. The vessel will always have the same position relative to the moving structure, while maintaining thesame absolute heading (setpoint) as shown in the followingillustration. At least one transponder must be selected for thisoption to be available.
8 301040/A
-
8/17/2019 K-Pos Follow Target Mode
9/16
Operator Manual
Follow Heading
Choose this to make the vessel follow the moving structure withrespect to heading. The vessel will always have the same heading
relative to the moving structure, while maintaining the sameabsolute position as shown in the following illustration. At leasttwo transponders must be selected for this option to be available.
Follow Position and Heading
Choose this to make the vessel follow the moving structure withrespect to both position and heading. The vessel will always havethe same position and heading relative to the moving structureas shown in the following illustration. At least two transpondersmust be selected for this option to be available.
301040/A 9
-
8/17/2019 K-Pos Follow Target Mode
10/16
Follow Target Mode
Reaction Limits
Position
Defines the reaction limit for position (reaction circle). The valueentered (between 0 and 1000m) is the radius of the reaction circlefor the mobile target.
Heading
Defines the vessel’s reaction sector for the heading relative to themoving structure.
Position Filter
Filter constant
Enter the required filter constant (0-100%) to increase or decrease the degree of position filtering. A high percentage(50-100%) gives a high filtering which is recommended if thereis noise or unstable measurements from the transponders. A low
percentage (0-50%) gives a low filtering which should be used if measurements from the transponders are stable and reliable.
4 ENTERING FOLLOW TARGET MODEYou can enter the Follow Target mode from either the Joystick or Auto Position mode.
1 Enable a fixed position-reference system as the reference
origin (see the Position Information chapter in the relevant K-Pos (OS) Operator Manual ).
2 Select Sensors→Reference System Settings.
• The Reference System Settings dialog box is displayed.
a Enable the transponder(s) on the target to be tracked.
b Check the Mobile check box for the transponder if necessary.
3 Select AutoPos →Follow Target.
• The Follow Target dialog box is displayed.
a In the Available list, highlight the mobile transponder you wish to use and click the Add button to select it.
b When using Follow Multiple Mobile Targets, selectthe required Operation mode.
c Set the required Reaction limits and Position Filtervalues.
d Click the Apply button to use the values entered inthe Follow Target dialog box.
4 Press the FOLLOW TARGET mode button twice.
• The FOLLOW TARGET
status lamp is lit.• The SURGE, SWAY and YAW status lamps are lit.
10 301040/A
-
8/17/2019 K-Pos Follow Target Mode
11/16
Operator Manual
• The reaction radius is displayed on the Posplot viewas a circle around the filtered position(s) of the mobile
transponder(s). For Follow Single Mobile Target, seeFigure 2. For Follow Multiple Mobile Targets see Figure3.
• Follow Single Mobile Target:
Figure 2 Posplot view in Follow Single Mobile Target mode
As the mobile transponder moves, the vessel’s position
setpoint remains unchanged.When the mobile transponder reaches the edge of its reactionradius circle, the position setpoint is updated automatically torestore the vessel to the same position relative to the target,and the reaction radius circle is redrawn around the new
position of the mobile transponder.
301040/A 11
-
8/17/2019 K-Pos Follow Target Mode
12/16
Follow Target Mode
• Follow Multiple Mobile Targets:
As the mobile transponders move, the vessel’s
position/heading setpoint(s) remain(s) unchanged.
When one of the mobile transponders reaches the edgeof its reaction radius circle, the position setpoint isupdated automatically to restore the vessel to the same
position/heading relative to the targets, and the reaction radiuscircles are redrawn around the new positions of all the mobiletransponders.
Figure 3 Posplot view in Multi Target mode
When the Follow Heading operational mode is selected in Follow Multiple Moving Targets mode, a Target Deviation presentationis given in the General view, see Figure 4. The lines indicate alimit where a heading change will be initiated.
Figure 4 Target Deviation presentation in General view
12 301040/A
-
8/17/2019 K-Pos Follow Target Mode
13/16
Operator Manual
5 CORRUPTED TRANSPONDER SIGNALSIt may occur that the signals from the target transponders arecorrupted. To avoid a sudden change in the vessel’s positionsetpoint because of unstable measurements, a position setpoint
jump test is performed. If the distance between the previous position and the new position is longer than a predefined limit, itis assumed that the change is caused by unstable measurents (no“real” position change).
The vessel maintains its present position and the followingwarning message is displayed.
Follow target relative angle rejected
In this event the operational advice is as follows:• Take the K-Pos system to Auto Position mode to reset the
Follow Target function.
• Consider using other target transponders and increasing thereaction limits.
6 HEADING CONTROLAll of the standard methods for heading control are available asdescribed in the Changing the Heading Setpoint chapter of the
relevant K-Pos (OS) Operator Manual .
In the Follow Target mode, choosing System Selected headingfrom the Change Heading dialog box will maintain the vesselat the heading that requires the minimum power in the currentenvironmental conditions.
System Selected heading is not available in Follow Multiple Mobile Targets mode when Follow Heading or Follow Positionand Heading is selected.
7 POSITION CONTROLWhen in Follow Target mode, you can change the distance tothe target whenever necessary. All of the standard methods for
position control are available as described in the Changing the Position Setpoint chapter of the relevant K-Pos (OS) Operator Manual .
8 SPEED CONTROLSee Speed Setpoint dialog box and the Speed page of the Position
dialog box in the Changing the Position Setpoint chapter of therelevant K-Pos (OS) Operator Manual for more information.
301040/A 13
-
8/17/2019 K-Pos Follow Target Mode
14/16
Follow Target Mode
9 ACCELERATIONSee Acceleration/Retardation Settings dialog box in the Changing the Position Setpoint and Changing the Heading Setpoint chapters of the relevant K-Pos (OS) Operator Manual for moreinformation.
10 RATE OF TURNSee Rate Of Turn page of the Heading dialog box in the Changing the Heading Setpoint chapter of the relevant K-Pos (OS)Operator Manual for more information.
14 301040/A
-
8/17/2019 K-Pos Follow Target Mode
15/16
Operator Manual
301040/A 15
-
8/17/2019 K-Pos Follow Target Mode
16/16
©2006 Kongsberg Maritime
P.O.Box 483N-3601 Kongsberg,
Norway
Kongsberg Maritime AS
Telephone: +47 32 28 50 00Telefax: +47 32 28 50 10
Service: +47 815 35 355
www.kongsberg.com
top related