installation 2013 accord aii 13026 instructions 4-door aug 2012 - bernardi parts honda · 2014. 11....
Post on 26-Mar-2021
9 Views
Preview:
TRANSCRIPT
Publications No.
Issue DateINSTALLATIONINSTRUCTIONS
Accessory Application
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47334 (1208) 1 of 1508V67-T2A-1000-90
AII 13026BACKUP SENSORS
2013 ACCORD4-DOOR
AUG 2012
PARTS LISTBackup Sensors Attachment KitP/N 08V67-T2A-100A
Control unit
Control unit bracket
Buzzer
Backup sensor harness
Subharness
2 Corner sensor clips
12 Wire ties
Aluminum tape
Fuse label
Flange bolt
2 Urethane tapes
Wire tie with holder(May not be used)
2 Center sensor clips
Connector clip(May not be used)
Accessory User’s Information Manual
2 of 15 AII 47334 (1208) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
Backup Sensor Kit
2 Center sensors
2 Corner sensors
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriverSmall flat-tip screwdriver10 mm Open end wrench10 mm and 14 mm SocketsPushpinRatchet3 mm Drill bitEye protection (face shield, safety goggles, etc.)FileScissorsRulerBlanketIsopropyl alcoholShop towel24 mm and 26 mm Hole sawsDrillHex wrenchDiagonal cuttersMasking tapeSteel wireElectrical tapeThe following tool is available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.• Trim Tool Set (T/N SOJATP2014)
(Blue)
(White)
Illustration of the Backup Sensors on the Vehicle
INSTALLATION
NOTE: Refer to Parts Information Bulletin (PIB) for the proper color sensors.1. Disconnect the negative cable from the battery.2. Remove the trunk floor (two clips).
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
QB21607BG
2A FUSE
BUZZERCONTROL UNIT
CORNER SENSOR CENTER
SENSORS SUBHARNESS
CORNER SENSOR
QB20601AX
2 CLIPSTRUNK FLOOR
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47334 (1208) 3 of 15
3. Remove the trunk rear trim panel (six clips and five hooks).
4. Pull the lever to fold the rear seat back forward.
QB20602BX
6 CLIPS
TRUNK REAR TRIM PANEL
5 HOOKS
QB20603AX
LEVER(Pull.)
REAR SEAT BACK(Fold forward.)
5. Push on the two tabs, and remove the cargo hook.
6. Pull away the weatherstrip. Remove the left trunk side trim panel (six clips).
QB20604AX
TABS(Push.)
CARGO HOOK
CARGO HOOK
QB20605CX
LEFT TRUNK SIDE TRIM PANEL
3 CLIPS
3 CLIPS
WEATHERSTRIP (Pull away.)
4 of 15 AII 47334 (1208) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
7. If equipped, remove the trunk panel (ten clips).
8. Remove the rear bumper.• On each side of the vehicle, attach masking tape
to the rear bumper, taillight, and rear fender as shown.
QB21401AG
TRUNK LID
10 CLIPS
TRUNK PANEL
QB21301AG
LEFT REAR FENDER
LEFT TAILLIGHT
REAR BUMPERMASKING TAPE
• Remove the two bumper screws, four self-tapping screws, and four clips.
• Release the seven retaining tabs on each side of the bumper.
QB21302BG
REAR BUMPER 4 CLIPS
2 BUMPER SCREWS
4 SELF-TAPPING SCREWS
QB21303AG
LEFT REAR FENDER
REAR BUMPER7 RETAINING TABS
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47334 (1208) 5 of 15
• Release the three retaining tabs on each side of the bumper.
• With the help of an assistant, remove the rear bumper (four retaining tabs).
• Place the rear bumper on a blanket.
QB21304AG
LEFT TAILLIGHT
3 RETAINING TABS
REAR BUMPER
QB21305BGREAR BUMPER
4 RETAINING TABS
9. Mark the inside of the rear bumper:• Locate the four scribe marks on the inside of the
rear bumper at the center and left side.• Using a pushpin, pierce the rear bumper at the
top and center of the two marks. NOTE: There are several markings on the inside of the rear bumper. Before piercing the rear bumper, verify you have the correct locations. NOTE: Make sure to pierce the scribe marks perpendicularly to the rear bumper.
10. Mark the inside of the rear bumper:
QB21402BG
PUSHPIN(Pierce perpendicularly.)
REAR BUMPER
REAR BUMPER
SCRIBE MARK (Not used.)
PUSHPIN
MARKSSCRIBE MARK
SCRIBE MARK
MARKS
SCRIBE MARK (Not used.)
PUSHPINPUSHPIN(Pierce perpendicularly.)
REAR BUMPER
6 of 15 AII 47334 (1208) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
• Locate the four scribe marks on the inside of the rear bumper at the center and right side.
• Using a pushpin, pierce the rear bumper at the top and center of the two marks. NOTE: There are several markings on the inside of the rear bumper. Before piercing the rear bumper, verify you have the correct locations. NOTE: Make sure to pierce the scribe marks perpendicularly to the rear bumper.
QB21403BG
PUSHPIN(Pierce perpendicularly.)
REAR BUMPER
REAR BUMPER
SCRIBE MARK (Not used.)
PUSHPIN MARKSSCRIBE MARK
SCRIBE MARK
MARKS
SCRIBE MARK (Not used.)
PUSHPIN
PUSHPIN(Pierce perpendicularly.)
REAR BUMPER
11. While wearing eye protection, drill all eight pierced marks: NOTE: Make sure to drill perpendicularly to the rear bumper.• Using a 3 mm drill bit, drill each pierced marks
from the outside of the rear bumper.
QB21404AG
DRILL(Drill perpendicularly.)
REAR BUMPER
8 HOLES
REAR BUMPER
DRILL3 mm DRILL BIT
8 HOLES
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47334 (1208) 7 of 15
• Using a 24 mm hole saw, enlarge the outboard (left and right corner sensor) bumper holes by drilling the lower 3 mm holes. Remove any burrs.
QB21405AG
DRILL(Drill perpendicularly.)
REAR BUMPER
REAR BUMPER
DRILL24 mm HOLE SAW
OUTER LOWER HOLE
OUTER LOWER HOLE
2 OUTER LOWER HOLES
24 mm 24 mm
• Using a 26 mm hole saw, enlarge the inboard (center sensor) bumper holes by drilling the lower 3 mm holes. Remove any burrs.
QB21406AG
DRILL(Drill perpendicularly.)
REAR BUMPER
REAR BUMPER
DRILL26 mm HOLE SAW
INNER LOWER HOLES
2 INNER LOWER HOLES
26 mm24 mm HOLE 24 mm HOLE
8 of 15 AII 47334 (1208) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
12. Using the sensor clips, install the two center sensors (Blue) into the 26 mm holes in the rear bumper. Note the direction and the pin location for each sensor.
13. Using the sensor clips, install the two corner sensors (White) into the 24 mm holes in the rear bumper. Note the direction and the pin location for each sensor.
QB21407AG
REAR BUMPER CENTER
SENSORS(Blue)
2 CENTER SENSOR CLIPS 2 CENTER
SENSORS(Blue)
QB21408AG
REAR BUMPER
2 CORNER SENSORS(White)
2 CORNER SENSOR CLIPS
2 CORNER SENSORS(White)
14. Plug the four subharness 2-pin connectors into the two center sensors (Blue) and the two corner sensors (White).
15. Secure the two subharness clips to the two center sensor clips as shown.
QB21409AG
SUBHARNESS
CENTER SENSOR(Blue)
CENTER SENSOR(Blue)
4 SUBHARNESS 2-PIN CONNECTORS
CORNER SENSOR(White)
CORNER SENSOR(White)
REAR BUMPER
QB21410AG
SUBHARNESS
REAR BUMPER
2 SUBHARNESS CLIPS
2 CENTER SENSOR CLIPS
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47334 (1208) 9 of 15
16. Using isopropyl alcohol on a shop towel, thoroughly clean the rear bumper where the aluminum tape will attach.
17. Secure the subharness to the rear bumper with the aluminum tape.
18. Using scissors, cut one urethane tape in half. Wrap the two cut pieces of urethane tape around the buzzer harness at the measurements shown.
19. Using scissors, cut one urethane tape into three pieces. Wrap the two 80 mm cut pieces of urethane tape around the buzzer harness at the measurements shown.
QB21411AG
SUBHARNESS
REAR BUMPER
ALUMINUM TAPE
Clean with isopropyl alcohol.
QB41708AB
URETHANE TAPE
20 mm (0.8 in.)URETHANE
TAPE (Cut in half.)
20 mm (0.8 in.)
20 mm (0.8 in.)
10 mm (0.4 in.)
80 mm (3.1 in.)
20. Route a piece of steel wire through the trunk area as shown.
21. Attach the connector end of the buzzer harness to the steel wire using electrical tape.
22. Gently pull the steel wire to route the harness through the trunk area. Remove the electrical tape and remove the steel wire.
QB41709AB
STEEL WIRE
LEFT TRUNK SIDE TRIM PANEL OPENING
STEEL WIRE
BUZZER HARNESS ELECTRICAL
TAPE
BUZZER
VEHICLE PANEL
QB41710AB
VEHICLE PANEL
BUZZER
STEEL WIRE (Remove.)
ELECTRICAL TAPE (Remove.)
10 of 15 AII 47334 (1208) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
23. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel where the buzzer will attach.
24. Remove the adhesive backing from the buzzer and attach it to the vehicle panel.NOTE: Make sure the buzzer is attached in the correct position. Do not cover the installation holes.
25. Using isopropyl alcohol on a shop towel, thoroughly clean the fuse case where the fuse label will attach. Attach 2A fuse label to the fuse case on the backup sensor harness.
QB41711AB
BUZZER
Clean with isopropyl alcohol.
ADHESIVE BACKING (Remove.)
VEHICLE PANEL
3N24080B
2A FUSE LABEL
BACKUP SENSOR HARNESS
FUSE CASE
Clean with isopropyl alcohol.
26. Route the backup sensor harness as shown, and plug the backup sensor harness 2-pin connector into the buzzer harness 2-pin connector.
27. Wrap the remaining piece of urethane tape (cut in step 19) around the buzzer harness 2-pin connector.
28. Gently pull the backup sensor harness 2-pin connector into the vehicle panel opening.
QB21503CG
BACKUP SENSOR HARNESS
BACKUP SENSOR HARNESS 2-PIN CONNECTOR
BUZZER HARNESS 2-PIN CONNECTOR
BUZZER HARNESS 2-PIN CONNECTOR
URETHANE TAPE (Cut in step 19.)
URETHANE TAPE
Align.
QB21504CG
BACKUP SENSOR HARNESS BACKUP SENSOR
HARNESS 2-PIN CONNECTOR
VEHICLE PAN-EL OPENING
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47334 (1208) 11 of 15
29. Secure the backup sensor harness to the vehicle harness with one wire tie.
30. Align the green tape on the backup sensor harness with the vehicle clip, and secure the backup sensor harness to the vehicle harness with one wire tie as shown.
31. Secure the backup sensor harness to the vehicle harness with one wire tie.
QB21505BG
VEHICLE HARNESS
WIRE TIE
VEHICLE CLIP
BRANCH SECTION (Align.)
QB21506CG
BACKUP SENSOR HARNESS
VEHICLE HARNESS
GREEN TAPE (Align.)
WIRE TIE
BACKUP SENSOR HARNESS
VEHICLE HARNESS
VEHICLE CLIP
32. Route the backup sensor harness along the vehicle harness, and secure it to the vehicle harness with four wire ties. Secure the wire ties beside the vehicle clips.
33. Unplug the vehicle 2-pin connector (Green) from the left taillight, and plug it to the backup sensor harness 2-pin connector.
QB21507CG
VEHICLE HARNESS
BACKUP SENSOR HARNESS
WIRE TIES
QB21508AG
BACKUP SENSOR HARNESS 2-PIN CONNECTOR
VEHICLE 2-PIN CONNECTOR (Green)
LEFT TAILLIGHT
12 of 15 AII 47334 (1208) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
34. Plug the backup sensor harness 2-pin connector into the left taillight.
35. Secure the 2-pin connectors to the vehicle harness with one wire tie.
36. Route the backup sensor harness along the vehicle harness, and secure it to the vehicle harness with one wire tie.
QB21509AG
BACKUP SENSOR HARNESS 2-PIN CONNECTOR
LEFT TAILLIGHT
VEHICLE HARNESS
WIRE TIE
2-PIN CONNECTORS
QB21510AG
WIRE TIE
VEHICLE CLIP
VEHICLE HARNESSBACKUP SENSOR
HARNESS
37. Install the control unit bracket to the control unit. Loosely install the flange bolt to the control unit bracket.
38. Plug the backup sensor harness 14-pin connector into the control unit.
QB21511BGCONTROL UNIT
CONTROL UNIT BRACKET
FLANGE BOLT (Loosely install.)
QB21512BG
CONTROL UNIT
BACKUP SENSOR HARNESS 14-PIN CONNECTOR
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47334 (1208) 13 of 15
39. Secure the control unit to the vehicle panel with the flange bolt loosely installed in step 37 as shown.
40. Secure the clip on the backup sensor harness to the vehicle panel.
QB21513CG
CONTROL UNIT
VEHICLE PANEL
LEFT TRUNK SIDE TRIM PANEL OPENING
CLIP
Slide.
FLANGE BOLT (Loosely installed in step 37.)
VEHICLE PANEL
41. Route the backup sensor harness along the vehicle harness.
42. Locate and remove the vehicle grommet from the rear panel.
43. Route the backup sensor harness through the hole, and seat the grommet on the backup sensor harness in the vehicle panel hole. NOTE: Do not pull on the backup sensor harness when installing the grommet.
44. Secure the backup sensor harness to the vehicle harness with three wire ties.
QB21601BGVEHICLE HARNESS
BACKUP SENSOR HARNESS
VEHICLE PANELVEHICLE
GROMMET (Discard.)
GROMMET
QB21602BG
BACKUP SENSOR HARNESS
3 WIRE TIESVEHICLE HARNESS
14 of 15 AII 47334 (1208) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
45. If equipped with vehicle harness, install the wire tie with holder to the backup sensor harness 8-pin connector, and secure it to the vehicle harness.
46. Install the connector clip to the backup sensor harness 8-pin connector, and secure it to the vehicle panel.
QB21603AG
BACKUP SENSOR HARNESS 8-PIN CONNECTOR
VEHICLE HARNESS
WIRE TIE WITH HOLDER
BACKUP SENSOR HARNESS 8-PIN CONNECTOR
WIRE TIE WITH HOLDER
QB21604AG
BACKUP SENSOR HARNESS 8-PIN CONNECTOR
CONNECTOR CLIP
BACKUP SENSOR HARNESS 8-PIN CONNECTOR
VEHICLE PANEL CONNECTOR
CLIP
47. With the help of an assistant, bring the rear bumper next to the rear of the vehicle, plug the subharness 8-pin connector into the backup sensor harness 8-pin connector, and reinstall the rear bumper.
48. Check that all wire harnesses are routed properly and that all connectors are plugged in.
49. Reinstall all removed parts.50. Reconnect the negative cable to the battery.51. Press and hold the radio power button for two
seconds to restore the radio and navi (if equipped) system functions.
52. Reset the clock on vehicle without navigation.53. Check that the backup sensors work properly as
described in the Accessory User’s Information Manual supplied with the backup sensor kit.
QB21605AG
BACKUP SENSOR HARNESS 8-PIN CONNECTOR
SUBHARNESS 8-PIN CONNECTOR
REAR BUMPER
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47334 (1208) 15 of 15
Adjust the Volume ControlThe factory setting is maximum volume. After confirming the operation, turn the volume control knob to the appropriate level, using a small flat-tip screwdriver. Do not force the adjuster as it could damage the unit.
QB21606AG
CONTROL UNIT
VOLUME CONTROL KNOB
Volume up
Volume down
top related