installation instructions aug 2004 - honda parts at hondapartsdeals.com: honda ... · 2005. 6....

© 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27510 (0408) 1 of 9

NOTE: The outside temperature gauge cannot beinstalled if the vehicle is equipped with optionalfog lights.

Fuse (3A)

Large fuse label

Owner's Manual

TOOL AND SUPPLIES REQUIRED

#2 Phillips screwdriver

Small flat-tip screwdriver

Felt-tip pen

10 mm Combination wrench

10 mm Socket

Ratchet

Diagonal cutters

Illustration of the Outside Temperature GaugeInstalled on the Vehicle

08E71-SDA-1000-91

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

AUG 2004

2005 ACCORD2- AND 4-DOOR

OUTSIDE TEMPERATUREGAUGE

P/N 08E71-SDA-100

AII 27510

PARTS LIST

Unit harness

Sensor assembly

17 Wire ties

2 Clips

Sensor harness

Washer-bolt

Small fuse label

Control unit

Unit bracket

SENSORHARNESS

UNITHARNESS CONTROL

UNIT

SENSORASSEMBLY 2312160T

712010T213010T

2213023T

2 of 9 AII 27510 (0408) © 2004 American Honda Motor Co., Inc - All Rights Reserved.

5. Remove the air duct cover (two clips), thenremove the air duct.

L4 Engine Model:

4. Release the three retaining tabs of the hood lockcover, and pull the hood lock cover.

V6 Engine Model:

INSTALLATION

equipment, and training to correctly and safely addequipment to your vehicle. These procedures shouldnot be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for theradio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

Routing the Sensor Harness

3. Open the hood. Remove the radiator cover (tenclips and four retaining tabs).

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,

HOOD LOCKCOVER

RETAININGTABS (3)

FRONT

CLIP AIRDUCTCOVER

AIRDUCT

CLIPAIRDUCTCOVER

AIRDUCT

FRONT

CLIPS (10)

RETAINING TAB

RADIATORCOVER


6. Remove the relay box (two bolts), and remove thebolt that fastens the air cleaner housing cover.

7. Remove the pin from the clip, and measure andcut off the pins in the area shown.

8. Attach the sensor assembly to the stay on thebumper beam using two clips and two pins.

9. Route the sensor harness 2-pin connector throughthe front bulkhead along the vehicle harness.

AIR CLEANERHOUSINGCOVER

BOLT

BOLT

RELAY BOX

BOLT(Remove.)

2 mm

CLIP

PIN

FRONT

CLIPS (2)

BUMPERBEAM

SENSORASSEMBLY

STAY PINS (2) SENSORASSEMBLY

STAY

CLIPS (2)

PINS (2)

SENSORHARNESS

2-PINCONNECTOR

VEHICLEHARNESS

FRONTBULKHEAD

FRONT


13. Near the battery, continue routing the sensorharness along the vehicle harness, and secure itto the vehicle harness with four wire ties.

14. Lift the air cleaner housing cover upward, androute the sensor harness toward the rear, alongthe vehicle harness.

10. Pull the hood lock cover, and route the sensorharness 2-pin connector toward the center of thevehicle along the vehicle harness. Plug the sensorharness 2-pin connector into the sensor 2-pinconnector.

11. Push the sensor harness clip into the hole on thesensor bracket.

12. Pull the hood lock cover, and secure the sensorharness to the vehicle harness with five wire tiesin the areas shown.

SENSORBRACKET

SENSORHARNESS

VEHICLEHARNESS

HOLE

SENSOR 2-PINCONNECTOR

SENSORHARNESS

SENSORHARNESS2-PINCONNECTOR

FRONT

WIRE TIE

VEHICLEHARNESS

WIRE TIESENSORHARNESS

WIRETIE

FRONT

VEHICLEHARNESS

SENSORHARNESS

AIRCLEANERHOUSINGCOVER

Lift

SENSORHARNESS VEHICLE

HARNESSFRONT

WIRE TIEVEHICLEHARNESS

WIRE TIE

SENSORHARNESS


15. Under the relay box, locate the vehicle 3-pinconnector blue-taped to the vehicle harness, andremove the blue tape to free the connector.Connect the sensor harness 3-pin connector intothe 3-pin connector you just freed. Secure thesensor harness to the vehicle harness with wireties in the areas shown.

A/T Model:

M/T Model:

NOTE: If the 3-pin connector is already beingused by another accessory, locate the 3-pinconnector taped to that other accessory harness.Remove the tape and dummy connector from thatother accessory harness. Plug the sensor harness3-pin connector into that other accessory harness.

BLUE-TAPE(Remove.) WIRE TIE

VEHICLEHARNESSRELAY BOX

SENSORHARNESS

VEHICLEHARNESS

VEHICLE 3-PINCONNECTOR

SENSORHARNESS 3-PINCONNECTOR

SENSORHARNESS

WIRE TIE

VEHICLEHARNESS

BLUE-TAPE(Remove.)

WIRE TIE

VEHICLEHARNESSRELAY BOX SENSOR

HARNESS

VEHICLEHARNESS

VEHICLE 3-PINCONNECTOR


VEHICLEHARNESS(Foldback.)

SENSORHARNESS

WIRE TIE

VEHICLEHARNESS

VEHICLE3-PINCONNECTOR


OTHERHARNESS 3-PINCONNECTOR

WIRE TIE


18. Remove the fuse box cover, and install the fuse(3A) provided into the No. 33 slot of the fuse box.

16. Remove the driver’s dashboard lower cover:

• Remove the self-tapping screw.

• Release the four clips on the left side first bypulling out on the driver's dashboard lowercover.

• After releasing the four clips, insert the flat-tipscrewdriver between the clip and thedashboard frame. Gently twist the screwdriverto release the clip.

• Release the two clips on the right side.

• Unplug the vehicle connector, and remove thelower cover.

17. If equipped, remove the driver’s dashboard undercover (release the three retaining clips, one pin,and one holder).

SELF-TAPPINGSCREW

CLIPS (7)

DRIVER'SDASHBOARDLOWER COVER

CLIP(Release theseclips first.)

CLIP(Release the clip by insertingthe flat-tip screwdriverbetween the clip and thedashboard frame, and twistthe screwdriver to release theclip.)

CLIP(Releasethese clipslast.)

FLAT-TIPSCREWDRIVER

VEHICLEFRAME

VEHICLECONNECTOR

DRIVER’SDASHBOARDUNDERCOVER

RETAININGCLIPS (3)

PIN

HOLDER

FUSE (3A)FUSE BOX

FUSE BOXCOVER


19. Attach the two fuse labels (2A) to the fuse caseson the unit harness.

20. Plug the 6-pin connector of the unit harness intothe fuse box.

NOTE: If the 6-pin connector is already being usedby another accessory, locate the 6-pin connectortaped to that other accessory harness. Removethe tape and dummy connector from that otheraccessory harness. Plug the unit harness 6-pinconnector into the other accessory harness.

21. Loosen the vehicle ground bolt, and install the unitharness ground terminal with this bolt.

22. Plug the unit harness 22-pin connector into thecontrol unit.

FUSE BOX

UNIT HARNESS 6-PINCONNECTOR

FUSE LABEL(2A)

UNITHARNESSFUSE CASE

UNITHARNESS6-PINCONNECTOR

DUMMYCONNECTOR

FUSE BOX

UNITHARNESS6-PINCONNECTOR OTHER

ACCESSORYHARNESS6-PINCONNECTOR

UNIT HARNESSGROUND TERMINAL

VEHICLEGROUND BOLT(Reuse.)

CONTROLUNIT

UNIT HARNESS22-PINCONNECTOR


23. On the left side of the steering hanger pipe, slidethe control unit onto the vehicle bracket that holdsthe cruise control unit.

With Cruise Control Unit:

Without Cruise Control Unit:

Install the unit bracket to the stay on the steeringhanger pipe with a washer-bolt, and slide thecontrol unit onto the unit bracket.

NOTE: If the 3-pin connector is already being usedby another accessory, locate the 3-pin connectortaped to that other accessory harness. Removethe dummy connector from that other accessoryharness. Plug the unit harness 3-pin connectorinto that other accessory harness.

24. On the left side of the steering shaft, locate the3-pin connector black-taped to the vehicleharness, and connect the unit harness 3-pinconnector into that 3-pin connector.

CRUISECONTROL UNIT CONTROL

UNIT

VEHICLEBRACKET

STEERINGHANGER PIPE

CONTROLUNIT

STAY

STEERINGHANGER PIPE

UNITBRACKET

WASHER-BOLT

UNIT HARNESS3-PIN CONNECTOR

VEHICLE3-PINCONNECTOR

STEERINGSHAFT

UNIT HARNESS3-PIN CONNECTOR

OTHER ACCESSORYHARNESS 3-PINCONNECTOR

DUMMYCONNECTOR


27. Check that all wire harnesses are routed properlyand all connectors are plugged in.

28. Reinstall all removed parts. Check that all clipsand fasteners are installed securely.

29. Reconnect the negative cable to the battery.

30. Enter the customer’s radio anti-theft code, andreset the radio station presets.

31. Reset the clock.

32. Check the operation of the outside temperaturegauge according to the outside temperature gaugeOwner's Manual.

NOTE: Whenever the battery is disconnected, thedriver’s window AUTO function is disabled.

33. Start the engine. Push down on the driver’swindow switch until the window is fully open.

34. Pull up on the driver’s window switch to close thewindow completely, then hold the switch for2 seconds or more.

35. Test the driver's AUTO window function.

25. Secure the unit harness to the vehicle harnesswith five wire ties in the areas shown.

26. Attach the fuse label (3A) over No. 33 on the backof the fuse box cover.

WIRE TIE

UNITHARNESS

WIRE TIE

VEHICLEHARNESS

WIRE TIE

FUSE LABEL(3A)

FUSE BOX COVER

No. 33

installation instructions aug 2004 - honda parts at hondapartsdeals.com: honda ... · 2005. 6....

Documents