elektronics - 2 @ hephy vienna m.pernickam.friedlc.irmlerj.pirkers.schmid steininger + beschäftigt...
Post on 06-Apr-2015
104 Views
Preview:
TRANSCRIPT
Elektronics - 2 @ Hephy Vienna HEPHYVIENNABELLE
M.Pernicka M.Friedl C.Irmler J.Pirker S.Schmid Steininger
+
Beschäftigt mit und CMS BELLE
Arbeitsbericht mit Blick in die Zukunft M. Pernicka
2004
2005
2006
2007
Start mit px-FED
Start mit AOH und mother cards
6 Prototypen fertig Tests in USA und PSI ? AOH gehen in Zusätzliche Wünsche Produktion, Tests
6 weiter px-Fed Produktion der Produktion mothercards für
den anal. und dig. Teil
Entwicklung diverser Proto typen für APV25 Belle ADC read out system start
Hit finding überprüft, offen wie weit Zeitmes= Hybrid auf Wien an der sung mit dem Produktion und FPGA Detektor Test teil nimmt Prototyp S/N Production
CMS BELLE
Analoge Mutterkarte für AOH abgeschlossen. Produktion von ??? In Wien.
Produktion von ??? AOH läuft. Tests im Inst.
In a certain time (F (shaping time,..)) only one hit information on one stripe.
A, Signal big enough …… time information B, To little Hit with out time information but with warning bit C. Hits on the boundary when 100 ns not enough
2 hits (or more) from one time on one stripe
Like a single hit
2 hits (or more) from different events and time on one stripe
A, Existing logic do not see 2 peaks, the 3 time sample do not fit in the expected curve. B, 2 peaks found but logic cannot find time. (A, ) C, time distance big enough, no pile up effect but still the logic do not find time because 2 max.
The result: A, 4 time data blocks for a event with good trigger timing or B, 6 data time blocks with bad trigger timing will be used for time calculation.
T(x)
T(x)
T(x)
T(x)
T(x)
T(x)
T(x)
T(x)
T(x)
T(x)
T(x)
T(x)
T(y)
T(y)
T(y)
T(y)
T(x)
T(x)
T(x)
T(x)
Case:
1 2 3
Problem: cluster with 2 tracks with different times
or not?
N
N+1
N+2
N+3 stripe
T6 T5 T4 T3 T2 T1 Time
Pulshöhe, Pos., Zeit, Qualität Pulshöhe, Pos., benützt für Ortsauflösung Benützt für Zeitmessung Wird nicht verwendet
S
i
d
e
t
e
Durch zusätzlicher Information zur eigentlicher Steifeninformation soll die Zeit des Hits und die Ortsauflösung verbessert werden.
N
N+1
N+2
N+3 stripe
T6 T5 T4 T3 T2 T1 Time
Signale über dem Thrshold aber sehr ``klein``
Pulshöhe, Pos., Zeit, schlechte Qualität Pulshöhe, Pos., benützt für Ortsauflösung Benützt für Zeitmessung Wird nicht verwendet
Trigger input Clock synchronized trigger TTM signals like clock, event number, …
4 anal signal
Clock. trigger
Control sig.
Secondrepeater
Clock in
- HV
? ?Control APVDAQ VME 9U
Box mit repeater für 48 APV
Prototypen: Control APVDAQ und Repeater zu bauen ist der 9U Control-APVDAQ von Wien Wer den Repeater baut und tested ist offen!
Si DetectorThermische Isolation
Fan hybrid
APV25
~100 µm thinned ~<100 µm 500µm 300 µm
Si. Det.
APV25 direct at the Si Det.
Vorteile: S/N um rund 1.8 mal besser. Wesentlich! Vieleicht auch leichter zu realisieren?
Nachteile: um rund 10-12% mehr Material. APV25 auf 100 µm abgeschliffen. Bedeckt rund 30% des Det. Kühlproblem noch wenig Erfahrung
Proposal for SVD2.5 Design(very preliminary)
Layer 1
Thinned APVs on Flex Hybrids
z Flex
r-phi: same as „standard“ solution (and SVD2.0)
r-phi APVs (not thinned) Sensor
Flex Hybrid print lay out senkrecht zum Beam
Sensor
APV25
Stiffened endPitch adapter(44152µm)
Stecker, Kabel zum Repeater
Mit der vorgeschlagenen Fan-Out Lösung hätte man um einiges mehr Leitungslänge zum APV25
Viel kürzere Leitungslänge
zwischen Si. Det. und APV25
top related