acer al1511 service guide - especmonitor.espec.ws/files/acer_al1514-al1511e_sm_635.pdf · 2012. 3....
TRANSCRIPT
- 1 -
Acer AL1514 (AL1511e)
Service Guide
Service guide files and updates are available on the CSD web: for more information, Please refer to http://csd.acer.com.tw/
100% Recycled Paper
- 2 -
Copyright Copyright © 2004 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written permission of Acer Incorporated.
Disclaimer The information in this guide is subject to change without notice. Acer Incorporated makes no representations or
warranties, either expresses or implied, with respect to the contents hereof and specifically disclaims any
warranties of merchantability or fitness for any particular purpose, Any Acer Incorporated software described in
this manual is sold or licensed “as is ”. Should the programs prove defective following their purchase, the buyer
(and not Acer Incorporated, its distributor, of its dealer) assumes the entire cost of all necessary servicing, repair,
and any incidental or consequential damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
- 3 -
Conventions
The following conventions are used in this manual:
Screen messages Denotes actual messages that appear on
screen Note Gives bits and pieces of additional information
related to the current topic.
Warning Alerts you to any damage that might result from doing or not doing specific actions.
Caution Gives precautionary measures to avoid possible hardware or software problems.
Important Reminds you to do specific actions relevant to the accomplishment of procedures.
- 4 -
Preface Before using this information and the product it supports, please read the following general information.
1. this Service Guide provides you with all technical information relating to the BASICCONFIGURATION
decided for Acer’s “global” product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2. please not WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide, for ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
Service of customer machines.
- 5 -
WARNING: (FOR FCC CERTIFIED MODELS) NOTE: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
Which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to
this equipment. It is the responsibility of the user to correct such interference.
As an ENERGY STAR® Partner our company has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
WARNING:
To prevent fire or chock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are
present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
- 6 -
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub,
Swimming pool or in a wet basement.
Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and
cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacture or
sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the
manufacture and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet area provided for ventilation. To ensure reliable
operation of the monitor and to protect it from overheating, be sure these openings are not blocked or
covered. Do not place the monitor on a bed, sofa, rug or similar surface. Do not place the monitor near or
over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation
is provided.
The monitor should be operated only from the type of power source indicated on the label. If you are not
sure of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug
will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the
three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance
safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect
the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or
electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous
voltages and other hazards. Please refer all servicing to qualified service personnel.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100-240V AC, Min. 3.5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
For use only with the attached power adapter (output 12V DC) which have UL,CSA listed license
- 7 -
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem.
NOTES Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch
and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness in the screen depending on the desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a
missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the
image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing
the image or turning off the Power Switch for hours.
- 8 -
Table of contents Chapter 1 MONITOR FEATURE ………………………………………………………….9 Chapter 2 OPERATING INSTRUTION …………………………………………………….15 Chapter 3 Machine assembly ……………………………………………………………21 Chapter 4 TROBLE SHOOTING ………………………………………………………….27 Chapter 5 CONNECTOR INFORMATION ……………………………………………….29 Chapter 6 FRU LIST ………………………………………………………………………..30 Chapter 7 SCHEMATIC DIAGRAM …………………………………………………………31
- 9 -
Chapter 1 Monitor Feature
Driving system TFT Color LCD
Size 15"
Pixel pitch 0.297 mm
Viewable angle 125(H) x 105 (V) degree
Brightness 250 cd/m2(typ)
Contrast Ratio 350:1 (typ)
LCD Panel Response time 25ms (Tr+Tf)
Video R,G,B Analog
Input Separate Sync H/V TTL
H-Frequency 31-61KHZ
V-Frequency 50-75HZ
Display Color 16.2 million Colors
Maximum Dot Clock ® 135MHz
Max Resolution 1024x768@75HZ
Plug & Play VESA DDC2B
ON Mode <50W
EPA ENERGY STAY OFF Mode <1W
Audio output Rated Power 1.0W rms(Per channel)
Input Connector D-Sub 15 pin
Input Video Signal Analog : 0.7Vp-p,75OHM
Horizontal : 304mm
Maximum Screen Size Vertical : 228mm
Power Source 90~240 Vac, 50~60HZ
Environmental Considerations
Operating Temp : 0 to 40 degree ; Altitude:3000mmStorage Temp : -20 to 60 degree ; Altitude :12000mmOperating Humidity : 5% to 90%
Weight (N.W.) 2.6kg
Dimension 344(W) x 361(H) x 149.8(D) mm
- 10 -
Switch
* Power Switch * MENU/ENTER * >/ Volume * </ Volume * Auto Adjust KEY
External Controls :
Function
* Contrast/brightness * Focus * Clock * H.Position * W.Position * Language * OSD Color temperature * OSD Position & Timeout * Auto Config * Input * Information * Reset * Exit
Regulatory Compliance UL, CSA, FCC, TUV/GS, CE, TCO99, ISO13406-2
- 11 -
Timeings The product has 21 memory modes in total. 12 modes are preset and 9 modes are user definable.
Timing 1 2 3 4 5 6 7 8 9 10 11 12
Standard DOS VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA
Data Pixel 640 640 640 640 720 800 800 800 800 1024 1024 1024
Data Line 350 480 480 480 400 600 600 600 600 768 768 768
H-Freq
kHz 31.469 31.469 37.861 37.500 31.467 35.156 37.879 48.077 46.875 48.363 56.476 60.023
V-Freq Hz 70.087 59.942 72.809 75.000 70.082 56.250 60.317 72.188 75.000 60.004 70.069 75.029
Pix Rate
MHZ 25.175 25.175 31.500 31.500 28.320 36.000 40.000 50.000 49.500 65.000 75.000 78.750
Hor.A [us] 0.318 0.636* 0.508 0.508 0.616 0.667 1.000 1.120 0.323 0.369 0.320 0.203
Hor.B [us] 3.813 3.813 1.270 2.032 3.813 2.000 3.200 2.400 1.616 2.092 1.813 1.219
Hor.C [us] 1.907 1.907* 3.810 3.810 1.907 3.556 2.200 1.280 3.232 2.462 1.920 2.235
Hor.D [us] 25.422 25.422 20.317 20.317 25.442 22.222 20.000 16.000 16.162 15.754 13.653 13.003
Hor.E [us] 31.778 31.778 26.413 26.667 31.778 28.444 26.400 20.800 21.333 20.677 17.707 16.660
Vert.A
[ms] 0.191 0.381 0.026 0.027 0.382 0.028 0.026 0.770 0.021 0.062 0.053 0.017
Vert.B
[ms] 0.064 0.064 0.079 0.080 0.064 0.057 0.106 0.125 0.064 0.124 0.106 0.050
Vert.C
[ms] 1.907 1.048# 0.528 0.427 1.111 0.626 0.026 0.478 0.448 0.600 0.513 0.466
Vert.D
[ms] 11.122 15.253 12.678 12.800 12.711 17.067 15.840 12.480 12.800 15.880 13.599 12.795
Vert.E
[ms] 14.268 16.683 13.735 13.333 14.268 17.778 16.579 13.853 13.333 16.666 14.272 13.328
Sync.Pol. +/- - / - - / - - / - -/+ + / + + / + + / + + / + - /- + / + + / +
Note: *Indicates horizontal front / back porch includes borders
# Indicates vertical front / back porch includes borders
- 12 -
Monitor Block Diagram
SCALAR MST8011A
DVI
+3.3V
RSDS AND LVDS
34063 +2.5V+12V
QDI LCDPANEL(1517 RSDSAND LVDS)
BRIGHTNESS
LCDPWR_ON3.3V
+3.3VEEPROM24LC08
ANALOG RGBPOWER
AUDIO_VOLUME
DDC
POWER INVERTER AND AUDIO BOARD
+3.3V
LCDVCC
INVCTRL
PCVGA
+3.3VAC 90-264V
+3.3V
+3.3V
AUDIO_MUTE
+2.5V
MICRO-CONTROLLERMTV312
AIC1739
+12V
LCDPWR_ON12V
- 13 -
PCB CONDUCTOR VIEW Main Board
- 14 -
Button Board
- 15 -
Chapter 2 OPERATING INSTRUCTIONS Front Panel Definition This Section defines the front panel User Interface for Led Indictor and Key function. Key Definition:
There are five keys defined in this system and described bellows. * Adjusting display settings
521 43
External Controls
1.
AUTO
If OSD is active, press to exit a selection in OSD. If OSD is inactive, press
and the monitor will automatically optimize the position, focus and clock of
your display.
2 < MINUS If OSD is active, press to select or adjust OSD options. If OSD is inactive,
press once, then press the buttons marked < or > to adjust the volume.
3 > PLUS If OSD is active, press to select or adjust OSD options. If OSD is inactive,
press once, then press the buttons marked < or > to adjust the volume.
4
OSD Function Press to view OSD.
Press again to enter a selection in OSD.
5
POWER
Power on/off
Green: power on
Orange: in sleep mode
- 16 -
OSD Menu
BRIGHTNESS:
This adjusts the brightness of the picture on
the screen.
CONTRAST:
This adjusts dark and light shades of color
relative to each other to achieve a
comfortable contrast.
Focus:
This removes any horizontal distortion and
makes the picture clear and sharp.
Clock:
If there are any vertical stripes seen on the
background of the screen this renders them
less noticeable by minimizing their size. It
also changes the size of the horizontal
screen.
H-Position:
This adjusts the horizontal.
V-Position:
This adjusts the vertical.
- 17 -
There are three ways of adjusting color:
Warm (Reddish white)
Cool (Bluish white)
User defined:
You can adjust the colors red, green and blue
to the intensity you desire.
LANGUAGE:
Select the OSD menu language from
English, German, and Spanish,
Traditional-Chinese, French, Italian, Japanese, Simple Chinese or Rusain
OSD SETTING:
This changes the position of the OSD
window on the screen and staying time
AUTO CONFIG
System runs auto-configuration.
- 18 -
INFORMATION:
This shows brief information on the screen.
RESET:
Recall to default settings
EXIT
Exit from OSD
LED Definition
The system equips one dual color (green/amber) led to indict system status and defined as
bellows :
System in power-off mode Dark
System in power-saving mode Amber
System in normal operation mode Green
System Status LED Color
- 19 -
LOGO : When the monitor is power on, the LOGO will be showed in the center, and disappear slowly.
HOW TO OPTIMIZE THE DOS-MODE Plug and play Plug & play DDC2B feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate
additional information about its display capabilities. The communication channel is defined in two levels, DDC2B.
The DDC2Bis a bidirectional data channel based on the I2C protocol. The host can request EDID information over
the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL. This monitor meets the Green monitor standards as set by the Video Electronics Standards Association(VESA)
and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is
no video-input signal present. When there is no video input signal this monitor, following a time-out period, will
automatically switch to an OFF mode. This reduces the monitor’s internal power supply consumption. After the
video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is
similar to a “Screen Saver” feature except the display is completely off. The display is restored by pressing a key
on the keyboard, or clicking the mouse.
- 20 -
USING THE RIGHT POWER CORD The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL
listed and CSA labeled. The voltage rating for the power cord shall be 125 volt AC.
Supplied with units intended for connection to power outlet of personal computer: Please use a cord set
consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a
grounding type attachment plug, rated 10A, 250V,CEE-22 male configuration. The other end terminates with a
molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration.
Please note that power supply card needs to use VDE 0602, 0625, 0821 approval power cord in European
counties.
- 21 -
Chapter 3 MACHINE ASSEMBLY This chapter contains step-by-step procedures on how to assemble the monitor for maintenance and trouble shooting NOTE : 1. The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding to avoid mismatch when putting back the components.
2. Note : The monitor surface is susceptible to scratching! Therefore, lay the monitor on a soft surface
when mounting or removing the base.
3. Wear gloves.
Front View : ( unit : mm )
- 22 -
Real View :
- 23 -
Top View :
Side View : ( unit : mm )
- 24 -
Picture Description
To assembly frame onto panel, let CCFT
cable through frame, then fix frame & panel
with screws
To put & fix bezel on panel
Insert LCD cable
1.Assemble power BD on the frame with screws 2.Stick mylar on power BD shielding
- 25 -
1.Assemble main BD on the frame with
screws
2.Insert LCD cable into main BD
Insert LCD cable into main BD.
Insert CCFL cable into power BD.
Fix button BD & bezel with screw
Fix VGA cable in main BD & the frame
To put and fix the rear cover
- 26 -
To fix the hinge stand assemble
- 27 -
Chapter 4 TROUBLE SHOOTING
This chapter provides trouble shooting information forAL1511
- 28 -
- 29 -
Chapter 5 Connector Information
Phonejack stereo PIN1. AC power cord : CEE22 typed connector PIN2. Audio cable PIN3. Audio : Line-in receptacle Video signal connector 15P Mini D-Sub connector x 1
CN6
DB15HD
1 6 2 7 3 8 4 9 5
11 12 13 14 1510
16 17
J1
PHONEJACK STEREO
1
23
PIN MNEMO SIGNAL
1 RV Red Video
2 GV Green Video
3 BV Blue Video
4 NC None
5 GND Ground(DDC return)
6 RG Red GND
7 GG Green GND
8 BG Blue GND
9 +5V + 5V (for DDC)
10 SG Sync GND
11 NC None
12 SDA DDC Data
13 HS Horizontal Sync
14 VS Vertical Sync
15 SCL DDC Clock
- 30 -
Chapter 6 FRU (Field Replaceable Unit) list
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of AL1511. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
NOTE : Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel(http://aicsl.acer.com.tw/spl/). For whatever reasons a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED CERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how best to dispose it, or follow the rules set by your regional Acer office on how to return it.
- 31 -
Chapter 7 SCHEMATIC DIAGRAM
6
Quanta Computer Inc.PROJECT : L5T
MCU AND BOTTON CONTROL
SCHEMATIC
3
Panel interface
4
CONTENTS
VGA AND TMDS INPUT
SCALAR MST8116A
7Audio
SHEET1CONTENT
BLOCK DIAGRAM 2
L5T MSTAR MB RSDS/LVDS
CONTENT
CONTENT
1 7Friday , February 27, 2004
B
Title
Size Document Number Rev
Date: Sheet of
5
- 32 -
+12VAC 90-264V
DVI
+3.3V
AIC1739
BRIGHTNESS
AUDIO_MUTE
+3.3V
POWER
POWER INVERTER AND AUDIO BOARD
+2.5V
+2.5V
PCVGA
+3.3V
LCDPWR_ON3.3V
+3.3V
SCALAR MST8011A
INVCTRL
DDC
RSDS AND LVDSQDI LCDPANEL(1517 RSDSAND LVDS)
BLOCK DIAGRAM
BLOCK DIAGRAM
2 7Friday , February 27, 2004
B
Title
Size Document Number Rev
Date: Sheet of
Quanta Computer Inc.PROJECT : L5T
LCDVCC
+3.3V +12V
34063
MICRO-CONTROLLERMTV312
EEPROM24LC08
+3.3V
ANALOG RGB
LCDPWR_ON12V
AUDIO_VOLUME
- 33 -
VGA_SDA_O
TX1+
CN2
VGA INPUT
13579
1113
2468101214
+++++++
+++++++
GREEN-IN
R4 33/6
BLUE-IN
R6 68/6
RED-IN
R212K/6/NC
R23 100/6/NC
C150.1U/6/NC
GREEN- 5
SDA-VGA 4
L7 100/6
D3DAN217K/NC
1
2
3
C4 0.047u
CN3
DVI-D/NC
12345678
910111213141516
1718192021222324
RX2-RX2+GNDRX4-RX4+SCLSDA
VS
RX1-RX1+GNDRX3-RX3+
5VGND
HP
RX0-RX0+GNDRX5-RX5+GND
RXC+RXC-
26
25
D21
Z5.6/NC
2
1
CN1
VGA/NC
162738495
11
12
13
14
1510
16
17
IN-V
RED+IN
D7
Z5.6/NC
2
1
C161U/6NC
R5
75/6/F
GREEN+ 5
RED-IN
T X2+
SDA-DDDC
VDD3V3
DSUB_5V
DDC_VS
HSYNC
TX0-
C6 0.047u
D11
BAT54C-GS08/NC
L1 100/6R1 33/6
R24 10K/6NC
VGA_SCL_O
VCC-DDC
R10 68/6
U1
24LC21/NC
1234 5
678
NCNCNCVSS SDA
SCKVCLKVCC
VSYNC
D5
Z5.6/NC
2
1
R202K/6/NC
IN-H
R2
75/6/F
VGA_SDA_O
R7 100/6
T X0- 5
VGA_CON 4
R25 10K/6NC
D15
Z5.6/NC
2
1
RED- 5
GND
RED+IN
GREEN+IN
BLUE+IN
VGA_CON_O
C5
NC
R11 100/6 HSYNC 5
T X2-
2
RED+IN
D19
Z5.6/NC
2
1
T X2+ 5
SDA-DDDC
BLUE-IN
C11
33P/6
D10
Z5.6/NC
2
1
C12
0.1U/6/NC
D18
Z5.6/NC
2
1
T X2- 5
T X0+
GND
1
R1090/6/NC
R172K/6/NC
C2
NC
BLUE+IN
R162K/6/NC
DDC-SDA
R9
75/6/F
IN-V
RED+IN
C10 0.047u
TX1-
SCL-DDDC
GREEN+IN
BLUE+IN
BLUE+INL6 FCM 1608C-300T06 (BULL WILL)
R1072K/6/NC
L36 100/6/NC
C14
0.1U/6/NC
Quanta Computer Inc.PROJECT : L5T
L5 100/6SCL-VGA 4VGA_SCL_O
PAGE1 VGAINPUT
VDD3V3
R12
2K/6
T XC- 5
IN-H
D6
Z5.6/NC
2
1
IN-H
C1 0.047u
BLUE- 5
SOGIN 5
DSUB_5V_O
DSUB_5V
DSUB_5V_O
C8 0.047u
D1
BAT54C-GS08/NC
L35 0/6
VDD3V3
T X1+ 5
VGA_CON_O
R26
10K/6NC
SCL-VGA
U2
M24C02/NC
1234 5
678NC
NCNCVSS SDA
SCKVCLKVCC
RED+ 5
VGA_SDA_O
C9
NC
C13
33P/6
D2DAN217K/NC
1
2
3
VGA AND TMDS INPUT
VGA AND DVI INPUT
3 7Monday , March 01, 2004
B
Title
Size Document Number Rev
Date: Sheet of
VSYNC 5
BLUE+ 5
HP-MCU 4
GREEN+IN
D32
Z5.6/NC 2
1
SCL-DDDC
R14 100/6
IN-V
R8 33/6
L2 FCM 1608C-300T06 (BULL WILL)
D22
Z5.6/NC
2
1
R15
2K/6
L3 FCM 1608C-300T06 (BULL WILL)
3
D20
Z5.6/NC
2
1
DDC_VS 4
GREEN-IN
DDC_VS
VGA_CON_O
D12
Z5.6/NC
2
1
IN-V
BLUE-IN
D17
Z5.6/NS
2
1
GREEN+IN
GREEN-IN
D8
Z5.6/NC
2
1
SOT23
D13
Z5.6/NC
2
1
D4DAN217K/NC
1
2
3
D9
Z5.6/NC
2
1
T X0+ 5
T XC+
R22 100/6/NC
R3 68/6
SDA-VGA
R13 100/6
T XC+ 5
T X1- 5
C7 0.01U/6
T XC-
IN-H
C3 0.047u
D14
Z5.6/NC
2
1
VCC-DDC
DDC-SCL
RED-IN
VGA_SCL_O
D16
Z5.6/NS
2
1
- 34 -
R27 390/1%
C39
0.1U/6
BCLKP 6BCLKN 6
BB0N 6
LVACKM 4
C24
0.1U/6
VDD3V3
RED+3
GPO4
PB25
VDD2V5
VDPLL
C42
22P/6
12
BG1N 6
C32
0.1U/6
VDVI
VDD
BG2N 6
C18
0.1U/6
PB12
PA24
T X2-3
PB13
PA14
R31 22/6
C30
22U
FG0P 6
PA20
R51 22/61 2
T XC+3
PA7
C29
0.1U/6
VDD3V3
LVACKP 4
U3
MST8136
63
60
6158
62
59
573738
404143444647495052
66
67
69
7071
3272
7374
106107
55 35 45
3
51 11 21 84 94 104
114
126
18 87 97 117
3956 36
2
54 42 10 20 85 95 115
127
19 86 96105
116
33
34
108109110111112113
9899100101102103
888990919293
161722232425678912131415122123124125128145
118119
120121
75767778
8382818079
2928
3031
5365
64 4868
RIN0
GIN0
SOGIN0BIN0
RIN0M
GIN0M
BIN0MHSYNC0VSYNC0
R+R-G+G-B+B-CK+CK-REXT
REFP
REFM
CSZ
SDASCL
HWRESETZINT
PWM0PWM1
RA0PRA0NA
VDD
AVDD_MPLL
AVDD_DVI
BYPASS
AVDD_DVI
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDC
VDDC
VDDC
VDDC
AVSS_DVI
AVSS
AVSS_MPLL
AVSS_LPLL
AVSS_PLL
AVSS_DVI
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
GNDC
GNDC
GNDC
GNDP
GNDC
XIN
XOUT
RA1PRA1NRA2PRA2NRA3PRA3N
GA1PGA1NGA2PGA2NGA3PGA3N
BA1PBA1NBA2PBA2NBA3PBA3N
RB1PRB1NRB2PRB2NRB3PRB3NGB0PGB0NGB1PGB1NGB2PGB2NGB3PGB3NBB0PBB0NBB1PBB1NBB2PBB2NBB3PBB3N
CLKAPCLKAN
CLKBPCLKBN
ESPOSP
EINVOINV
GPO0GPO1GPO2GPO3GPO4
DDC1_CLK/GPO8DDC1_DAT/GPO7
DDCROM_CLK/GPO6DDCROM_DAT/GPO5
AVDD_PLL
AVDD
AVSS
AVSS_DVI
AVSS
T X0+3
BG1P 6
LVB2P 4
FXDIO 6
PB6
XTAL4
PB11
C17
22U
PB5
C34
0.1U/6BB0P 6
BB2N 6
L13
0/8
L9
CX601T02001/8
BR2N 6
FB0N 6
PB19
C28
22U
BR0P 6
PB2
T X1+3
L12
CX601T02001/8
GREEN-3
YCLK 6
OSP
FG1N 6
L8
CX601T02001/8
BG0P 6
PB15
PB21
X1
14.318MHz
BG2P 6C37
0.1U/6
SDA4
FG1P 6
PB10
PA6
C21
0.1U/6
BB2P 6
C25
22U
PA10
VPO
PB18
R33 22/6
C40
0.1U/6
R28 100/6
VPLL
FCLKP 6
XSTB 6
R30 22/6
PA25
BXDIO 6
VOLUME7
INT4
PA11
RESET4
VDD
BLUE+3
PA23
FG2N 6
LVB2M 4C96
0.1U/6/NC
1
2
C41
22P/6
12
PA4
VDD3V3
FG0N 6
SOGIN3
GPO1
L10
CX601T02001/8
YDIO 6
BRIGHTNESS4
FB2P 6
FB1P 6
R32 NC
VDPLL
FR2N 6
C98
0.1U/6/NC
1
2
VDD3V3
PA18
VDVI
FB0P 6
BR1P 6
CSZ4
PB20
VAD
FR0N 6
PA15
C22
0.1U/6
T X2+3
BB1P 6
RED-3
ESP
PA13
Dual Input
MST8011A
MST8116/8136A
4 7Friday , February 27, 2004
B
Title
Size Document Number Rev
Date: Sheet of
GPO3
C19
0.1U/6
BB1N 6
C26
0.1U/6
R34 22/6
FR0P 6
OINV
R29 100/6
POL 6
PA12
C38
0.1U/6
C36
22U
GPO2
BG0N 6
PB4
SCL4
C97
0.1U/6/NC
1
2
BR2P 6
FB1N 6
FR2P 6
PB14
PA3
C35
0.1U/6
VAD
GREEN+3
PA2
L11
CX601T02001/8
FB2N 6
BR0N 6
C23
0.1U/6
C33
22U
FR1N 6
PB23
PB3
PB7
FG2P 6
FCLKN 6
VPO
PB24
GPO0
C31
0.1U/6
T X1-3
Quanta Computer Inc.PROJECT : L5T
YOE 6C43 0.1U/6
HSYNC3
PA21
PA19
R110
10K/NC
VPLL
VDD3V3
T XC-3
FR1P 6
PA22T X0-3
BLUE-3
PB22
VSYNC3
VDVI
C20
0.1U/6
BR1N 6
PA5
C27
0.1U/6
NC
12V
SCL5
C46
0.1U/6
1
2
L20BC0610R6H-B246-2_5/NC
HP-MCU 3
VCPU
VDD3V3
R67
2.2K/F/6
SEL_O
D37
DAN217K/NC
1
2
3
VCPU
LEFT
C62
330U/16V
6
SDA-VGA3
MENU
MENU
GND
R113 2.2K/61 2
Q122N3904
23
1
GND
PWR_SEL
LED_G
C53
22P/6
12
VDD3V3
VCC12
C92
0.1U/6
2
INT5
UP
R92
2K
1
2
D35
DAN217K
1
2
3
R96 4.7K/6
1 2
VDD3V3
L21
47UH
1
2
R61 10K/612
U4
24LC08B
1234 5
678
A0A1A2VSS SI
SCKWP
VCC
MENU_O
R41
82K/6
12
UP_O
R106
33K//6/NC
1
2
R681K/6
L18 0/81 2
SCL_1
R45
NC
1
2
R38
10K/6
1
2
2
STBY 7
SCL_OSEL
C99
0.1U/6/NC
1
2
LED_R
SDA-VGA
D25
DAN217K
1
2
3
C82
0.1U/6
8
GND
VCPU
C68
0.1U/6
R55 10K/612
C93
0.1U/6
VDD3V3
R100
33K/6
1
2
D26 EC10QS0421
CPU
R71 10K/6
GND
C52
22P/6
12
VDD3V3
C70
22U
R108 0/120612
DEBUG PORT
2
C50
22P/6
1
2
LEFT
R50 22/612
L40 22/6/NC1 2
C59
0.1U/6
1
2
FUSE10/12061 2
R54 2.2K/61 2R53 2.2K/61 2
C47
0.1U/6
1
2
VGA_CON 5
C54 0.1U/6/NC12
7
VDD3V3
L19
0/8/NC
1 2
VDDCTRL_2 6
R44
10K/6
1
2
C44
0.1U/6
1
2
DOWN
VDD3V3
MUTE
L16 330/61 2
10
MH0003
C57330u/16V
R95
NC
1
2
L41 100/6/NC1 2
R946.8K
1
2L23
0/612
3
VCPU
R97 4.7K/6
1 2
Q1MMST3906
R88
10K
1
2
R39
33K/6
1
2
R18 100/6
TO BUTTON BOARD
2.0mm pitch 90° E&T
VDDCTRL_1 6
LED_R
4
R49 22/612C48
0.1U/6
1
2
L37 1K/61 2
Q10
MMST3906
VDD3V3
C100
0.1U/6/NC
1
2
R
PWR_SEL
CN4
4501-10-10P-R
12345678910
C550.1U/6
R35
2K/6
1
2
DSUB_5V
PC5V_OFF
Q2MMST3906
GND
SCL_1
C69
0.1U/6
R111 471 2
1
PWR
RIGHT
C49
22U
1
2
VDD3V3
R901K
1
2
VDD3V3
LED_G
R66 3.6K/F/6
VDD2V5
SEL
VDD3V3
PC5V_OFFR69
10K/6
R64
0/6
R36
2K/6
1
2
VDD3V3
U6
MC34063
1
2
3
45
6
7
8SWITCH
EMITTER
TIMING
GNDCII
VCC
SENSE
DRIVE
VDD3V3
VCC12
GNDR93
1K
1 2
R60
100/6
12
PWR
L2210K/6
12
C101
1U/6
D24
DAN217K
1
2
3
5
R42 NC1 2
L15 1K/61 2
9
NC
VCPU
SDA5
DDC_VS3
PW0007
LED_R
GND
MUTE7
C65
1U/8
MCP810M3X-2.93
VDD3V3
UP
R1122.2K
1
2
C51
22P/6
1
2
R48 22/612
R1143.3
1
2
VDD3V3
XTAL5
PW0004
DOWN
PW0003
C58
330U/16V/NC
R65
10K/6
SDA_1
PWR_O DOWN_O
D30
3.3V
2
1
R58 NC12
C63
330U/16V/NC
VDD3V3
VDD3V3
R56 10K/61 2
C94
0.1U/6/NC
1
VDD3V3
DISPLAY
MCU & BUTTON
5 7Monday , March 01, 2004
B
Title
Size Document Number Rev
Date: Sheet of
RESET 5
R52
10K/6
1
2
C64
0.1U/6/NC
D23
1N4148/NC
CN5
JWT-A2001WV2-06/NC
1234
1234
LEFT_O
CN6 CONN 4x2-R
45 6
1 23
8
C95
0.1U/6/NC
VCPU
VDD3V3
R102 0/6/NC1 2
U5
MTV312
171820212223
2425
7
2928
19
4
1314
56
11
12 10
4344
3031
3233
3736
4115
40
42
1
23
916
2627
8
39
3835
34
P1.0P1.1P1.2P1.3P1.4P1.5
P1.6P1.7
RST
P3.0/RXD/HSCLP3.1/TXD/HSDA
P3.2/INT0
VDD3
P3.4/T0/ISDAP3.5/T1/ISCL
NCNC
X2
X1 VSS
HSYNCVSYNC
P6.4/DA10P6.5/DA11
P6.6/DA12P6.7/DA13
P4.1/HBLANKP4.0/VBLANKK
P5.4/DA4P4.2/STOUT
P5.5/DA5
P5.3/DA3
P5.2/DA2
P5.1/DA1P5.0/DA0
P6.3/AD3P6.2/AD2
P6.1/AD1P6.0/AD0
VDD
HALFV/DA8
HLFHO/DA9HCLAMP/DA7
P5.6/DA6
LED_G
R91
4.7K
1
2
D33
DAN217K
1
2
3
R19 100/6
R40
33K/6
1
2
GND
C56
0.1U/6
SS0003
U8
NC
1 2
3
VCC RESET
GND
R98 100/6
R99
33K/6
1
2
BRIGHTNESS 5
RIGHT_O
VDD3V3
G
R59 22/612
POWER
Q3MMST3906
R43
NC
1
2
D34
DAN217K
1
2
3
CSZ5
INVCTRL
MH0001
X211.0592MHz
C60
470P/6
1
2
R89 100R1 2
VCC12
UP
VCPU
VCPU
R63
0.3/1206
R37
10K/6
1
2
R57 0/6/NC1 2
R47 100/6
1 2
modify debug port
R46 100/61 2
D36
DAN217K/NC
1
2
3
SDA_1
Quanta Computer Inc.PROJECT : L5T
R105
33K/6/NC
1
2
VDD3V3
INVCTRL
C61
0.1U/6
1
2
L39 1K/61 2
PW0006
SCL-VGA3
L17 330/61 2
L14 1K/61 2
V
VCPU
SCL-VGA
RIGHTDOWN
Q11
MMST3906
GND
SDA_O
R701K/6
L38 1K/61 2
Q4
AIC1739
3 1
2
VIN VOUT
GND
GND
PW0005
PARAMETEREEPROM
3
MH0002
C45
0.1U/6
1
2
R101
33K/6
1
2
Q5SN7002E
3
2
1
1
- 35 -
VDDCTRL_1 4
C87
470P/6
1
2
CN8
AF730B-A2G1T/NC
123456789101112131415161718192021222324252627282930 GND
LCDVDD
GND
B
Q6 SI2301DS/NC
3
2
1
GND
GND
C77
2200P/61
2
C90
330U/16V
LCDVCC
YOE5
GND
C88
1N/6
1
2
VCC12
BG0N5
LVB2P
C86
0.1U/8
1
2
1
H3
MTH276D126
2345 6
789
2
BCLKP5
FG2N5
1
H1
MTH276D126
2345 6
789
C76
2200P/6
1
2
1
1
LCDVCC
GND
FG0P5
1
H2
MTH276D126
2345 6
789
FG0P
R85 3.6K/F/6
C74
0.1U/6/NC
1
2
FR1P5
GND
R77
10K/6
E
D
YCLK5
BR1P5
FR2P5
BR2N5
GND
LCDVCC
GND
LVACKP
VCC12FG1P5
R76
10K/6/NC
C
BR1N
LCDVDD
C81
0.1U/6
1
2
FR0P5
R103
0/8/NCFB0P
R74
82K/6
C75
330U/16V/NC
E
BG1P5
LCDVCC1
BG2N5
FXDIO5
C
VDD3V3
LVACKM
BB0N5
FG1N5
1
LVB2M4
FB1N
R73
10K/6/NC
1
2
1
H4
MTH276D126
2345 6
789
BB1N5
FR1N5
BG0P5
FG0N
Quanta Computer Inc.PROJECT : L5T
G
GND
1
1
D
R87
47K/6
1
2
LVB2M
L290/8/NC
GND
C89
0.1U/6
1
2
FB1P
R75
10K/6
1
2
FB2P5
Q7 SI2301DS
3
2
1
G
VDDCTRL_2 42
2
FCLKN5
LVB2P 4
C72
2200P/6/NC
1
2
1
GND
BR0N
BB1P5
BB0P5
FCLKN
LCDVCC
R813.6K/F/6/NC
BB2N5
Q8
DTC144EUA/NC
2
3
1
FB2N5
GND
C78
0.1U/6
1
2
R83
0/1206
BR0P
BR0P5
FB0P5BB2P5
1
L32
47UH
1
2BG1N5
BG2P5
YDIO5
FCLKP5
3
3
CN9
1841 30P
13579
11131517192123252729
24681012141618202224262830
1357911131517192123252729
2468
1012141618202224262830
DISPLAY
PANEL INTERFACE
6 7Monday , March 01, 2004
B
Title
Size Document Number Rev
Date: Sheet of
GND
D29 EC10QS0421FG0N5
BCLKN
Q9
DTC144EUA
2
3
1
S
C79
330U/16V POL
BR2P5
XSTB5
BR0N5
FB0N5
S
BXDIO5
C80
0.1U/6
1
2
LCDVCC
LCDVCC5
FR0N5
LVACKP 4
LCDVCC
L28 0/8/NC
FB0N
R821.2K/F/6/NC
R72
82K/6/NC
LCD
BR1P
GND
GND
FB1P5
FG2P5
R86
2.2K/F/6
3
LVACKM4
B
POL5
L26 0/8/NC
R104
0/8
U7
MC34063
1
2
3
45
6
7
8 SWITCH
EMITTER
TIMING
GNDCII
VCC
SENSE
DRIVE
LCDVCC5
FR2N5
L27 0/8/NC
2
BCLKN5
BCLKPFCLKP
L30 0/8/NC
BR1N5
LCDVDD
3
FB2PFB2N
C73
2200P/6/NC1
2
CN7
AF750B-A2G1T/NC
1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950
FB1N5
- 36 -
LIN_PC
AC2
0.1U/6
AGND
GND
AL8 BEAD/1206
AGND
GNDAR13 10K/6
VCC12
AR43.9K/6
Z0415
AL6 BEAD/1206
AU1
TDA7496L
4
9 5
6
7
17
1412
11
10
13
15 16
1 2 3 19 2018
INL
INR VAROUT_L
VOLUME
VAROUR_R
OUTL
OUTRMUTE
STBY
SVR
GND
VS
VS
GND
GND
GND
GND
GND
GND
AL4 600/CX601T020011 2
AC5330U/16V
SPKOUTL
SPKOUTR
ACN1
4606-04-04P-R
1234
AL3 600/CX601T020011 2
PCAUDIO-IN
VCC12
AC10 0.
1U/8
RIN_PC AC6 0.47U/8
AGND
AR5 100/6
R_LINE
AR10 CX201209805/8AR8 20
K/6
AL7 BEAD/1206
AGND
VCC12
MUTE4
AL5
BEAD/1206
AC8 22
0P/6
VCC12
AC4 0.47U/8
VOLU
AR11 10K/6
AR3 10K/6
AL1 BEAD/1206
Z0416
AL2 BEAD/1206/NC
AR14 10K/6
MUTE
AC11
330U/16V
AQ3
DTC144EUA
2
3
1
AR7 20
K/6
AJ1
ZD005D10023451
AGND
VOLUME5
DISPLAY
Audio
7 7Friday , February 27, 2004
B
Title
Size Document Number Rev
Date: Sheet of
Quanta Computer Inc.PROJECT : L5T
AGND
AR1 1K/6
AR6 100/6
L_LINE
AR9 CX201209805/8
AC1
1U/8
STBY
AQ2
DTC144EUA
2
3
1
AGND
AGND
STBY4
AR2 10K/6
AGND
AGND
AC3
330U/16V
AR12 10K/6
AQ1
SN7002E
3
2
1
AC9330U/16V
AC7
220P/6
VOLU