abc of raw materials - pci magazine | solutions for ... · abc of raw materials | 2 | introduction...

ABC of Raw Materials

CHEMICAL RAW MATERIALS

ABC OF RAW MATERIALS

| 2 | INTRODUCTION

Raw Materials from Worlée – Modules to your Success.“Our raw materials are important modules for our customers’ success” says Reinhold von Eben-Worlée, CEO and general manager.

For more than 160 years Worlée has delivered raw materials from all over the world to its customers. The hanseatic trading company has grown into an international production and service company with three units: Chemical raw materials, natural raw materials and cosmetic raw materials.

The combination of a high quality approach, technical know-how and the intuition for trends and market developments is the reason why Worlée is a reliable partner – in all three departments.

Chemical Raw Materials from Worlée

Worlée-Chemie GmbH produces in its plants in Lauenburg and Lübeck additives and bin-ders for a broad range of coatings. Products from well-known suppliers complete the deli-very program.

Our production plants comply with highest environmental, quality and security standards.ISO 9001 and ISO 14001 as well as the inte-grated security management system show Worlée as a responsible company.

At Worlée sustainability is not only a word. For our excellent management of energy, emission and resources, Worlée has received the “Responsible Care” award of VCI Nord several times and become the first so called “Klimaschutz-Unternehmen” of its type.

All our departments continuously work on the development of our products so that Worlée can contribute to your success. Module by module. Day by day.

CHEMICALRAW MATERIALS

NATURAL RAW MATERIALS

COSMETIC RAW MATERIALS


TABLE OF CONTENTS | 3 |

Table of Contents

ADDITIVES page

WORLÉE Silicone additives for improving substrate properties in solvent based/aqueous paint systems

WorléeAdd 6/7

Adhesion promoter WorléeAdd 6

Cobalt free catalysts WorléeAdd 7

Corrosion inhibitors WorléeAdd 8

Additives for Paints and Lacquers Resiflow 8

Defoamers for Solvent Based and -free Systems, Aqueous Systems

WorléeAdd 9

Miscellaneous WorléeAdd 10

Additives for Powder Coatings WorléeAdd Resiflow

10/11

Specialities for Powder Coatings WorléeAdd Resiflow

12

1 component primer coatings for polyolefinic substrates

Special-Primer 12/13

Rheological Additives (Bentonite) WorléeAdd 8XX 13

CABOT High porous Aerogels based on Silica EnovaTM 13

CHEMARK Matting Hardeners / Powder Coating Additives

Chemark 14

CINKARNA Ultrafine Titanium Dioxide Suspension CCR 14

CWK Colloidal Silica Dispersions Köstrosol® 14

Micronised Silica Powders Köstropur® 15

BINDERS page

WORLÉE Polyesterpolyols, solvent based and solvent free, saturated

WorléeRes E 33

Epoxy Esters, Drying WorléeDur 33

Special Hardeners for Epoxy Resins, free of Nonylphenol

WorléeCure 33

Hard Resins, Phenol Modified WorléeFen 34

Maleic Resins WorléeSin 35

Gilsonite Solutions WorléeGilsol 35

Natural Gums (Damar, Copal, Shellac and Shellac Solutions)

WorléeGum 36

Styrene-Butadiene-Copolymer WorléeCop 37

Inorganic-organic hybrid systems WorléeProtect 37

Acrylic Resins, Water Based Dispersions and Solutions for Printing Inks and OPV´s

Zinpol 38

POLYOLS & POLYMERS

Keton Aldehyde Resins Polytone 38

BRUNO BOCK VOC-free Polythiole based on Mercaptocarboxylic Acids

Thiocure® 38/39

AGC Natural Asphaltum Gilsonite® 39

COLOR page

WORLÉE Pigment Preparations WorléeTransoxid 41/42

WorléePaste 41

Electroconductive Quartz WorléeQuarzsand AS

42

CABOT Carbon Black Black Pearls® 43/44

Elftex® 43/45

Emperor® 44

Mogul® 43

Monarch® 43/44

Regal® 43/44

Vulcan® 45

ISHIHARA Titanium Dioxide Tipaque 45

SINLOIHI Daylight Fluorescent Pigments 46

BINDERS page

WORLÉE Acrylic Resins, Solvent and Water Based, Hydroxyl Group Containing

WorléeCryl A 17

Acrylic Resins, Solvent Based, Thermoplastic WorléeCryl L 18

Acrylic Resins, Water Based Dispersions and Solutions

WorléeCryl 18/19

Acrylic Resins, Water Based Dispersions and Solutions for Printing Inks and OPV´s

WorléeCryl 19/20

Starch Copolymer Dispersions for Printing Inks and OPV´s

WorléeDex 20

Alykd Resins, Solvent Based, Airdrying, Short Oil, Medium Oil, Long Oil

WorléeKyd 20–25

Alkyd Resins, Solvent Based, Long Oil, Urethane Modified

WorléeKyd 26

Alkyd Resins, Solvent Based, Stoving systems, Reactive and NC-Combination

WorléeKyd 27

Alkyd Resins / Acrylic Resins, Solvent Based, Thixotropic

WorléeThix 28/29

Alkyd Emulsions, PU-modified, Water Based WorléeSol E 29

Alkyd Emulsions, Water Based WorléeSol NW 30

Alkyd Resins, Water Based, Air and Forced Drying

WorléeSol 30

Alkyd Resins, Water Based, for Stoving Systems

WorléeSol 31

Polyesters, Water Based, Oil Free, Saturated WorléePol 31

Polyesterpolyols, Solvent Free, Saturated WorléePol 32

Polyesters, Solvent Based, Saturated WorléePol 32


| 4 | ADDITIVE| 4 | ADDITIVEITIVE | 4 | ABC OF RAW MATERIALS

ABC of raw materials

Worlée’s roots were based in the trading of natural resins. Still today Worlée can deliver Shellac, Copal or Damar to its customers. Since our beginning Worlée’s special focus has been on production and technical competence through our laboratories in Germany and Asia together with our technical skilled sales force.

The combination of our raw material modules and raw material modules of renowned part-ners means Worlée can offer a large product range:

A – AdditivesB – BindersC – Color // Pigments

With our long experience and the technical know-how of our application experts Worlée offers high quality products, an extensive technical service and assistance for the deve-lopment of new products.

You will find products from Worlée and our partners in various application areas:

Decorative Paints & CoatingsIndustrial CoatingsPowder CoatingsConstructionPrinting InksWoodAdhesivesSpecial Applications

Various application areas of products from Worlée

ADDITIVES


ADDITIVES | 5 |


| 6 | ADDITIVES

A WorléeAddSilicone additives for improving substrate properties in solvent based paint systems

Type Appearance Forms of delivery Addition Main uses and principal characteristics

WÁdd 75 slightly turbid liquid 100 % 0,01–0,5 % Multifunctional additive for improving promoting, slip, leveling and scratch resistance.

W’Add 311, 10 %

W’Add 311, 30 %

Clear to slightly turbid, low viscous liquids

10 % in xylene

30 % in xylene

0,1–1,0 %

0,03–0,3 %

Silicone based, for paints, lacquers and leather finishes. Improve mar resistance, slip, flow, gloss, reduce foaming, pinholing and orange peel.

W’Add 312 Clear, low viscous liquid 10 % in isop. HC 170–200 0,1–1,0 % Silicone based additive, especially for decorative paints. Eliminates cell structure and brush marks, improves flow, mar resistance and slip. Specially designed for aromatic free decorative paints.

W’Add 315 Clear to slightly yellow liquid 10 % in iso propanol 0,5–1,0 % Silicone based additive, for water and solvent based paints, improving mar resistance and slip, flow and gloss.

W’Add 327 Clear, low viscous liquid 20 % in iso propanol 0,1–1,5 % Silicone based, mainly for water thinnable lacquers and paints, improves wetting of plastic and aluminium substrates, increases mar resistance and slip, avoids cratering.

WÁdd 398 Clear to slightly yellowish liquid 100 % 0,2–1,5 % Multifunctional paint additive for improving leveling, scratch resis-tance, surface smoothness and gloss. Contains primary OH-groups.

W’Add 356 Colourless low viscous liquid 30 % in xylene 0,2–1,0 % Silicone based additive, for solvent based coatings, improves deairing, levelling, mar resistance, slip and gloss, reduces orange peel and cratering. Also suitable for curtain coatings. Thermostable in stoving systems.

WÁdd 361 Colourless, low viscous liquid 10 % in xylene 0,1–0,5 % Hammer effect additive to get hammer effect paints.

WÁdd 373 N Colourless, low viscous liquid 3 % in isop. HC 150–180 0,2–1,0 % Silicone based additive with multifunctional properties. Used in solvent based coatings mainly to achieve surface smoothness and mar resistance. At the same time it works as antifoam agent and avoids surface imperfections.

W’Add 429 Colourless liqud 10 % in solvent blend 0,5–1,5 % For improving the efficiency of matting agents in solvent based silk gloss decorative paints. Additionally improvement of flow and scratch resistance, deairing.

A WorléeAddAdhesion promoter


W’Add 480 N Clear, colourless liquid 70 % in iso propanol 1,0–5,0 % Special epoxy ester to improve the adhesion of aqueous baking enamels and polyurethane systems on metallic substrates.

WÁdd 482 Clear, colourless liquid 80% in n-butyl acetate 2,5–5,0 % Reactive polymeric adhesion promoter for improving adhesion of polyurethane- and stoving systems mostly on substrates as glass, ceramic and tiles, but also on metallic substrates.

WÁdd 484 Colourless to light yelllow liquid 75 % in solvent blend 1,0–3,0 % Special polyester resin for improving adhesion of solvent based two component PU and stoving paints on metals substrates. Improves elasticity and flow. NMP-free.

WÁdd 486 Colourless to light yelllow liquid 75 % in solvent blend 1,0–3,0 % Special adhesion promoter for solvent based systems for air drying and oven cured systems.

WÁdd 487 Colourless to light yelllow liquid 78 % in solvent blend 1,0–3,0 % Like W’Add 486. Does not contain n-methyl-2-pyrrolidone.


ADDITIVES | 7 |

A WorléeAddSilicone additives for improving substrate properties in aqueous paint systems


WÁdd 75 slightly turbid liquid 100 % 0,01–0,5 % Multifunctional additive for improving promoting, slip, leveling and scratch resistance.

WÁdd 315 Clear to slightly yellow liquid 10 % in isopropanol 0,5–1,0 % Silicone based additive, for water and solvent based paints, improving mar resistance and slip, flow and gloss.

WÁdd 327 Clear, low viscous liquid 20 % in isopropanol 0,1–1,5 % Silicone based, mainly for water thinnable lacquers and paints, improves wetting of plastic and aluminium substrates, increases mar resistance and slip, avoids cratering.

WÁdd 330 Clear, slightly yellowish, low viscous liquid

10 % in butyl glycol 0,3–0,5 % Silicone based, reduce surface tension of water thinnable systems, improve levelling, reduce edge pulling, eliminate surface imper-fections.

WÁdd 340 Clear to slightly hazy, yellowish liquid, low viscous

100 % in dipropylene glycol monomethyl ether

0,1–1,0 % Excellent substrate wetting additive for aqueous systems, reduces surface tension, low tendency to stabilize foam.

WÁdd 345 Clear to slightly turbid yellowish liquid

71 % in solvent blend/water 0,3–1,5 % Special modified silicone polyether for aqueous systems for impro-ving subtrate wetting and penetration on absorbend substrates.

WÁdd 351 Turby, creamy liquid 70 % in water/butyl glycol 0,5–1,0 % High molecular silicone additive to improve slip, mar resistance and antiblocking, for aqueous systems.

WÁdd 352 Turby, creamy liquid 70 % in water/propylene glycol 0,5–3,0 % High molecular silicone additive to improve slip, mar resistance and antiblocking, for aqueous systems.

A WorléeAddCobalt free catalysts


WÁdd 2000 Clear to slightly hazy low viscous liquid

30 % in butyl acetate/polyglycol

0,5–1,2 % Catalyst for solvent based and aqueous isocyanate crosslinkingsystems.

WÁdd 2030 Clear, amber coloured, low viscous liquid

28 % in isobutanol / MPA

0,4–2,0 % Catalyst for solvent and water based stoving finishes. Improves water, salt spray and detergent resistance.

WÁdd 2500 Brownish liquid approx. 12 % in solvent mixture 1,5–3,0 % Cobalt-free catalyst to support the oxidative drying of alkyd resin paints. Metal complex.

WÁdd 2600 Clear yellowish liquid approx. 12 % in solvent mixture 0,5–1,0 % Metal-free catalyst to support the oxidative drying of alkyd resin paints together with metal complex based dryers.

WÁdd 2700 Clear brownish liquid approx. 12 % in solvent mixture 0,5–2,0 % Cobalt-free catalyst to support the oxidative drying of aqueous systems. Metal complex.


| 8 | ADDITIVES

A WorléeAddCorrosion inhibitors


WÁdd 456 Colourless liqud 30 % in water 0,5–3,0% Nitrit-free anti-flash rust agent and corrosion inhibitor for aqueous paints and lacquers.

WÁdd 458 Colourless liqud 30 % in water 0,2–2,0% Nitrit-free anti-flash rust agent for aqueous paints and lacquers.

A ResiflowAdditives for paints and laquers

Type Appearance Forms of delivery Addition* Main uses and principal characteristics

Resiflow FK 70 Colourless liquid 70 % in methoxypropanol 0,3–2,0 % Silicone free anti-floating and flow control agent e.g. for polyester/melamine resin based stoving paints. Eliminates craters, pinholes and fisheyes.

Resiflow FL 2 Colourless, high viscous liquid min. 98 % 0,2–2,0 % Silicone free acrylic flow control agent for solvent based and solvent free coatings based on alkyd, polyester, acrylic, vinyl, epoxy and polyurethane resin.

Resiflow FL 9 Colourless, high viscous liquid min. 98 % 0,2–1,5 % As Resiflow FL 2, but often better compatibility.

Resiflow FM 4 Colourless, high viscous liquid min. 98 % 0,2–2,0 % As Resiflow FL 2, but with improved efficiency.

Resiflow FM 4-50 50 % in xylene 0,4–4,0 %

Resiflow L 3075 Clear viscous liquid 75 % in arom. HC 155-180 0,2–2,0 % Silicone free acrylic flow control agent for solvent based coatings, correct surface imperfections, especially suitable for coil coating systems.

Resiflow LH-240 Viscous liquid min. 98 % 0,2–1,5 % Flow control and degassing additive for solvent based and solvent free formulations of different composition, including gel coats.

Resiflow LH-241 Clear, viscous liquid min. 98,5 % 0,2–2,0 % Silicone free acrylic flow control agent for solvent based and solvent free coatings based on alkyd, polyester, acrylic, epoxy, polyurethane resins etc. Excellent compatibility, especiallysuitable for clear coats.

Resiflow LW Colourless to slightly yellow, low viscous liquid

min. 98,5 % 0,2–1,5 % Silicone free acrylic flow control agent for solvent based and solvent free coatings, similar to Resiflow FL 2 but lower in viscosity.

Resiflow W 51 Colourless, medium viscous liquid 50 % in butyl glycol/iso propanol 0,5–3,0 % Silicone free acrylic flow control agent for mainly water based coating systems as well as solvent based stoving systems (very good compatibility). Effective pigment wetting agent.

Resiflow W 52 Colourless, medium viscous liquid 50 % in butyl glycol/iso propanol 0,5–3,0 % Silicone free acrylic flow control agent for mainly water based coating systems as well as solvent based stoving systems (very good compatibility). Effective pigment wetting agent.

Resiflow W 5200 Colourless, high viscous liquid min. 96 % 0,2–1,5 % Silicone free polymer flow control agent, especially for aqueous coatings but also for solvent based systems.

W’Add 100 Colourless, high viscous liquid min. 98 % 0,1–1,0 % Polymeric, silicone free flow control agent for solvent based and solvent free coatings, UV-resistant, good recoatability, avoids surface imperfec-tions. Corresponds to FDA § 175.300.

W’Add 101 Colourless, high viscous liquid min. 98 % 0,1–1,0 % Silicone free acrylic flow control agent for solvent based and free coatings and printing inks of different composition. Avoids also surface imperfections. Corresponds to FDA § 175.300.

WÁdd 137-70 Colourless high viscous liquid 70 % in xylene 0,1–1,0 % Silicone free acrylate leveling agent for solvent based and solvent free coatings. Fluor modified. Especially good recoatability.

Resiflow L 66 F Clear, viscous liquid Min. 98,5 % 0,2–2,0 % Liquid functional flow control agent. Excellent transparency in TGIC-powder clear coats. Use via a master batch production.

*calculated on total formulation

THE EDGE OF INNOVATION

ESTRONC H E M I C A L


ADDITIVES | 9 |

A WorléeAddDefoamer for solvent-based and -free systems


WÁdd 370 Colourless, low viscous liquid 10 % in solvent blend 0,03–0,5 % Fluor silicone based defoamer and deairing agent for solvent based paints and inks of different compositions as well as EP-coatings.

WÁdd 372 Colourless, low viscous liquid 5 % in methoxy propyl acetate 0,05–0,8 % Fluor silicone based defoamer and deairing agent for solvent based and high solid coatings. Especially for decorative paints.

WÁdd 425 Clear, yellowish liquid 51 % in solvent blend 0,2–1,5 % Silicone free antifoam agent and defoamer, especially suitable for wax containing coil coating structure paints and two component EP floor coatings.

WÁdd 602 Clear liquid 1,3 % in isop. HC 170–200 0,4–2,0 % Silicone based antifoam agent mainly for two component-PU and EPcoatings.

WÁdd 603 Clear liquid 13,2 % in isop. HC 0,2–1,5 % Polyacrylate modified silicone defoamer for solvent based and solvent free coatings of different compositions.

WÁdd 6235 Clear liquid 6,5 % in solvent mixture 0,5–2,0 % Highly effective silicone defoamer for reactive thicklayer systems based on epoxy resins.

WÁdd 6236 Clear to slightly turbid liquid 100 % 0,01–0,5 % Highly effective silicone defoamer especially suitable for solvent free PU-coatings.

A WorléeAddDefoamer for aqueous systems


WÁdd 624 Clear liquid 25 % 0,5–3,0 % Silicone based, aromatic and APEO free defoaming solution for water based systems of different composition.

WÁdd 628 Slightly turbid liquid 66 % 0,1–1,0 % Silicone based defoamer solution for aqueous formulations.

WÁdd 6210 Turbid liquid 80 % 0,1–1,5 % Highly efficient glycol ether-free defoamer for aqueous formulati-ons. Especially suitable for printing inks and overprint varnishes.

WÁdd 6226 Colourless viscous liquid 100 % 0,5–1,0 % Silicone based, siliceous defoamer emulsion for aqueous formulati-ons. Very good grinding defoaming

WÁdd 6410 White thixotropic liquid 26 % 0,1–1,0 % Silicone based, siliceous defoamer emulsion for aqueous formulati-ons. Very easy incorporation possible, especially for PU, PU-hybrid and alkyd emulsions.

WÁdd 6420 White thixotropic liquid 26 % 0,1–1,0 % Silicone based, siliceous defoamer emulsion for aqueous formulati-ons. Easy incorporation possible.


| 10 | ADDITIVES

A WorléeAddMiscellaneous


WÁdd 410 N Clear to slightly turbid yellowish, low viscous liquid

0,5–2,0 % Viscosity stabilizer, anti-skinning and anti-gelling agent for solvent based air drying and stoving paints.

WÁdd 411 N Clear, slightly turbid, yellowish, low viscous liquid

0,5–2,0 % Like WorléeAdd 410 N, but aromatic free.

WÁdd 412 Colourless liquid 65 % in water 0,5–1,0 % Solvent free compatibility agent for easier incorporation of driers into water based alkyd emulsion paints.

WÁdd 422 50 % in iso propanol/methoxy propanol 0,2–0,8 % Cationic surface active additive for increasing the conductivity of electrostatic sprayable paint systems, low addition.

WÁdd 425 Clear, yellowish liquid 51 % in solvent blend 0,2–1,5 % Silicone free additive, imparts an equal structure to coil coatings which contains wax. Improves degassing, reduces popping, also for clear coats.

WÁdd 428 Clear low viscous liquid 10 % in solvent blend 3,0–6,0 % Silicone free additive for structured coil coatings without wax addition, for achieving orange peel effect. Improves degassing.

WÁdd 700 Milky liquid 60 % in water 2,0–5,0 % Silicone based, for aqueous systems to increase water resistance, gloss, adhesion and weather resistance. Best effect after more than 16 hours of addition into the ready made product.

WÁdd 781 Clear, medium viscous liquid 100 % 0,1–2,0 % Silicone free additive for solvent based, solvent free and water based systems to improve levelling, flexibility and adhesion. Two component-PU-coatings of high film thickness show reduced blistering.

WÁdd FR 5000 White powder Min. 98 % approx. 10,0 % Halogen-free flame retardant additive based on encapsulated Phosphor compounds for water based binders

WÁdd 8905 Colourless liquid 15 % in water approx. 5,0 % Alkaline ZnO- solution for cross-linking water based carboxy func-tional acrylic polymers to increase the water resistance, optimize the block resistance, increase the heat stability and maximise the film hardness.

A WorléeAdd/ResiflowAdditives for powder coatings

Type Appearance Addition* Main uses and principal characteristics

W’Add 18 White powder 0,5–1,5 % Silicone free powder flow control agent for general industrial applications.

W’Add 101 P White powder 0,5–1,5 % Silicone free powder flow control agent for high gloss powder coatings and clear coats.

W’Add 360 Flaked solid 0,5–2,0 % Low molecular weight, hydroxy functional polymeric silicone additive for better mar resistance, slip and flow.

W’Add 902 White powder 0,5–1,5 % For reducing the melt viscosity, thus improving deairing and degassing. Best results in combination with very low amounts of benzoine (0,1-0,2 %). Especially suitable for non-yellowing powder coa-tings, for instance when cured in gas fired ovens.

W’Add 904 White granulate 0,5–4,0 % For reducing the melt viscosity, thus improving deairing and degassing. Best results in combination with very low amounts of benzoine (0,1-0,2 %).

W’Add 915 White powder 1,5–2,5 % Catalyst for better mechanical properties of GMA-acrylic powder systems based e.g. on Isocryl EP-570.

W’Add 1200 White powder 0,3–6,0 % Micronized synthetic wax improving slip properties and mar resistance of powder coatings. Excellent deairing effect. At higher concentrations it may also function as a flatting agent.

W’Add ST-70 White powder 0,1–0,5 % Stannous octoate catalyst for PU powder coatings.


ADDITIVES | 11 |

A WorléeAdd/ResiflowAdditives for powder coatings

Type Appearance Addition* Main uses and principal characteristics

Resiflow CP 77 White powder 0,7–1,5 % Silicone free powder anti-cratering agent. Also suitable for powder clear coats and UV systems.

ResiflowL 66 F MBP 10

White granulate 5,0–15,0 % Flow control agent based on a masterbatch (10 % Resiflow L 66F, 90 % carboxyl-functional polyester with acid value of approx. 35). Excellent clarity in powder clear coats.

Resiflow P 64 F White powder 0,2–2,0 % Powder functional flow control agent for powder clear coats of all types, especially for GMA acrylate systems. Due to the compatibility the transparency is hardly reduced.

Resiflow P 65 F White powder 0,2–2,0 % Powder functional flow control agent for powder clear coats of all types, especially based on epoxy.

Resiflow P 67 White powder 0,7–1,5 % Silicone free powder flow control agent with good allround properties.

Resiflow PH-240 White powder 0,5–2,0 % Powder functional flow control agent with excellent flow without increasing „pill flow“; especially suitable for PU powder systems and PUR clear coats.

Resiflow PL 200 White powder 0,7–1,5 % Silicone free powder flow control agent with good intercoat adhesion when recoated with powder or liquid paints.

Resiflow PL 220 White powder 0,7–1,5 % Powdery flow control agent with unique compatibilizing and anti-cratering robustness.

Resiflow PV 5 White powder 0,5–1,5 % Silicone free powder flow control agent for powder coatings of all types. Very freeflowing and yellowing resistant.

Resiflow PV 88 White powder 0,5–1,5 % As Resiflow PV 5, but on another silicate carrier.





| 12 | ADDITIVES

A WorléeAdd/ResiflowSpecialities for powder coatings

Type Appearance Addition* additional information Main uses and principal characteristics

Acrylic crosslinker GMA-300

Water bright granu-lates

1,0–7,0 % 105–120 °C softening range High reactive acrylic crosslinker for increasing crosslinking density, e.g. in Hybrid-, Primid and PU systems. Also as binder component for UV systems.

Epomatt G-151

Granulate 2,0–10,0 % 115–125 °C softening range Matting agent for epoxy powder coatings, especially in combination with OTB-epoxy hardeners. Non-yellowing. Also for NIR-application.

Epomatt G-152

Granulate 2,0–10,0 % 115–125 °C softening range Matting agent for matt and dead matt epoxy and hybrid powder coatings. Matting of low temperature curing epoxy powders in combination with Epoxy Hardner G-91 and of low temperature curing (140 °C) hybride powders with suitable poyester type. Also for NIR application.

Epoxy Hardener G-91

Granulate 2,0–4,0 % 92–106 °C softening range Imidazole adduct for curing epoxy powder coatings at low baking temperature (130 °C) with still good mechanical properties.

Epoxy Hardener G-92

Granulate 6,0–24,0 % 80–100 °C softening point Catalysed phenolic curing agent for epoxy resins. Imparts excellent chemical resistance and mechanical properties at fast cure (200 °C) or low temperature cure (120 °C).

Escat50

Off-white granulates 0,3–0,6 % Substituted Imidazole/wax blend to improve curing of powder coatings; easily dispersible.

Isocryl EP-540 Granulate 17–20 % to 80–83 % poly-ester with acid value 30–35

120–135°C softening point With carboxylic polyesters and Primid XL 552 as Co-hardener silk gloss, outdoor-resistant "one-shot" powder coatings can be formulated with excellent mechanical properties and good chemical resistance.

IsocrylEP-570 G

Flakes 17–20 % 140–155 °C softening point GMA-matting resin for one-shoot matt outdoor powder coatings with good abrasion resistance and surface levelling, also suitable for matt clear coats.

Isocryl EP-575 Granulate 20–30 % to 70–80 % poly-ester with acid value 30–35

120–135 °C softening point In combination with carboxylic polyesters and Primid XL 552 as Co-hardener dead matt, outdoor-resistant "one-shot" powder coatings are obtained, with good impact and chemical resistance.


A Special-Primer1 component primer coatings for polyolefinic substrates

Type Appearance Forms of delivery

Application Main uses and principal characteristics

Special-Primer AP 1010

White (pigmented) 4,0 % in xylene Undiluted: spraying, dipping, rolling, printing Adhesion promoter for EPDM, PP and blends of these as used for the automotive industry for spoilers, bumpers, dashboards etc. for subsequent painting, printing and sticking. Special-Primer AP 1010 can be used in aerosol cans.

Special-Primer AP 1030

White (pigmented) 4,0 % in xylene Undiluted: spraying, dipping, flow coating, rolling, printing

Adhesion promoter for EPDM, PP and blends of these as used for the automotive industry for spoilers, bumpers, dashboards etc. for subsequent painting, printing, sticking and coating.

Special-Primer PE 6800

Colourless to yellowish, clear

5,0 % in xylene Application as 2,5 % solution Adhesion promoter for untreated polyethylene for subsequent coating or printing.

Special-Primer PP 3200 W

Low viscous, beige cream coloured liquid

30 % in water Application diluted with water to 10 % solids con tent by spraying, dipping or printing

Aqueous adhesion promoter based on especially modified, low hlorinated polypropylene for PP, polyolefinic blends and with restrictions for PE.

Special-Primer PP 4400 W

Brownish, turbid liquid 40 % in water Application diluted with water to 10 % solids content by spraying, dipping or printing

Chlorine-free primer and adhesion promoter based on special modified polypropylene used for polypropylene and polyolefinic blends.

Special-Primer PP 5130

Colourless to yellowish,clear

2,5 % in xylene 5,0 % in xylene

Application as 2,5 % solution Adhesion promoter for untreated polypropylene for subsequent painting, printing, sticking. Batteries, packaging film, heels, toyes, foils etc.




ADDITIVES | 13 |

A Special-Primer1 component primer coatings for polyolefinic substrates

Type Appearance Forms of delivery

Application Main uses and principal characteristics



5,0 % in xylene Application as 2.5 % solution Same as PP 5130, with improved adhesion promotion on different PP substrates and aluminium.



10 % in xylene Application as 2.5 % solution Same as PP 5130, with improved adhesion promotion on different PP substrates and aluminium.


Colourless to Yellowish,clear

2,5 % in xylene Application as 2.5 % solution Adhesion promoter for untreated polypropylene for subsequent painting, printing, sticking. For batteries, heels, toys, foils, garden furniture etc. Best adhesion properties.

Special Primer PP 8300

Clear/slightly turbid, yellowish, low viscous liquid

5,0 % in xylene Spraying, dipping, printing Chlorine free adhesion promoter mainly for polypropylene, PP/EPDM and thermoplastic rubbers.

A WorléeAddRheological Additives (Bentonite)

Type Composition Color Form Density [g/cm3]

Particle size dispersed [£gm]

Main uses and principal characteristics

W’Add 810 Organic derivative of a smectite Light cream Fine powder 1,8 < 1 Rheology control in systems with low polarity

W’Add 820 Organic derivative of a smectite Light cream Fine powder 1,9 < 1 Rheology control in systems with low to medium polarity

W’Add 827 Organic derivative of a smectite Light cream Fine powder 1,9 < 1 Rheology control in systems with high polarity

W’Add 830 Organic derivative of a smectite Light white Fine powder 2,4 Rheology control in water based systems

W’Add 840 Organic derivative of a smectite Light cream Fine powder 1,7 < 1 Rheology control in polar systems

W’Add 850 Organic derivative of a smectite Light cream Fine powder 1,7 < 1 Rheology control in systems with low polarity

W’Add 855 Organic derivative of a smectite Light cream Fine powder 1,7 < 1 Rheology control in systems with no polarity to high polarity

W’Add 860 Organic derivative of a smectite Light cream Fine powder 1,6 < 1 Rheology control in systems with no polarity to high polarity

W'Add 875 Organically modified smectite clay Milkwhite Fine powder 1,8 <1 Rheology control in water based systems

W'Add 885 Organically modified smectite clay White-light cream

Fine powder 1,9 <1 Rheology control in water based systems

Market(s) served: EUROPE

A Cabot – Enova™ Aerogel High porous hydrophobic Aerogels based on Silicia

Type Delivery form

Particle size [µm]

Pore diameter [nm]

Density [kg/m³]

Thermal conductivity [mW/mK]

Applications and properties

EnovaTM Aerogel IC 3110

Granules 100–700 ca. 20 ca. 120 ca. 12 Extremely low thermal conductivity. Additive for thermal insulating coatings

EnovaTM Aerogel MT IC 3120

Granules 100–1.200 ca. 20 ca. 120 ca. 12 Extremely low thermal conductivity. Additive for thermal insulating coatings

Market(s) served: WORLDWIDE


| 14 | ADDITIVES

A ChemarkMatting hardeners

Type Chemical name Appearance Main uses and principal characteristics

Chemark 1331 2-Phenyl Imidazoline White to off-white fine powder

Matting hardener for epoxy resin based powder coatings

Chemark 1355 Salt of 1, 2, 4, 5-Benzenetetracarboxylic acid & 4, 5-dihydro-2-phenyl-1H-imidazole

Off-white to pale yellow flake

Hardener for highly reactive epoxy resin powder coatings.

Chemark 1368 Salt of 1, 2, 4, 5-Benzenetetracarboxylic acid & 4, 5-dihydro-2-phenyl-1H-imidazole

White to off-white fine powder

Matting hardener for pure epoxy or epoxy/polyester resins pow coatings.

Chemark 1374 Tetrakis (methoxymethyl) glycoluril White powder or granules Cross linking agent


A CinkarnaWaterbased ultrafine TiO2 dispersions

Type Description Surface modifier Main uses and principal characteristics

CCR 130 Ultrafine TiO2-dispersion SiO2 , Al2O3 Translucent UV-protection for various substrates, for alkyd emulsions

CCR 150 Ultrafine TiO2-dispersion Al2O3 , Fe2O3 Translucent UV-protection for various substrates, for acrylate dispersions

CCA 100 BS Ultrafine TiO2-Dispersion – Photocatalysis

Market(s) served: GERMANY, SWITZERLAND, BENELUX, POLAND, CZECH REPUBLIC, SLOVACIA

A CWKColloidal Silica Dispersions

Type Appearance avg. particlesize [nm]

SolidContent[~ % m/m]

pH valueat 25 °C

Stabili-zer

main uses and principal characteristics

Köstrosol 0730 Opalescent liquid

7 30 10 Na2O Colloid-disperse solution of SiO2 in water. Additive to formulate heat and corrosion resistant coatings, improve of scratch resistance, improve of mechanical properties, to keep transparency, for fast curing systems, good green concrete strength.

Köstrosol 1540 Opalescent liquid

15 40 10 Na2O Colloid-disperse solution of SiO2 in water. Additive to formulate heat and corrosion resistant coatings, improve of scratch resistance, improve of mechanical properties, as filler and matting agent and as derivatisation component.

Köstrosol AD 1530 Opalescent liquid

15 30 6 Na2O Colloid-disperse solution of SiO2 in water. Additive to formulate heat and corrosion resistant coatings, improve of scratch resistance, improve of mechanical properties, good compatibility with many additives, universal use.

Köstrosol 3550 Milky liquid 45–50 50 10 Na2O Colloid-disperse solution of SiO2 in water. Additive to formulate heat and corrosion resistant coatings, improve of scratch resistance, improve of mechanical properties, as filler and matting agent, stable against various additaments, turbid effect.

Köstrosol 2040 AS Opalescent to slight turbid liquid

20 40 9 NH3 Colloid-disperse solution of SiO2 in water. Additive to formulate heat and corrosion resistant coatings, improve of scratch resistance, improve of mechanical properties, as filler and matting agent, as derivatisation component and especially suitable for alkali-sensitive applications.

Köstrosol® is a registered trademark of Chemiewerk Bad Köstritz GmbH.Market(s) served: WORLDWIDE


ADDITIVES | 15 |

A CWKMicronised Silica Powders

Type H2O [%] avg. particlesize d50 [µm]

BET surface[m2/g]

pH value Application

Köstropur 020408 Max. 3 4 250–400 5,5–7,5 Filler for certain plastics (PA6, PA66, PMMA etc.) to improve mechanical

Köstropur 020508 Max. 3 5 250–400 5,5–7,5 For plastics as an anti-blocking agent, untreated, (PP/PE).

Köstropur 100808 8–12 7 300–420 5,5–7,5 Filler for certain plastics (PA6, PA66, PMMA etc.) to improve mechanical

Köstropur 020612 Max. 3 6 4,0-7,0 For plastics as an anti-blocking agent (PP/PE).

Köstropur 021012 Max. 3 10 250–400 5,5–7,5 For plastics as an anti-blocking agent (PP/PE).

Köstropur 050618 Max. 5 6 4,0–7,0 Matting agent for coatings and paints.

Köstropur 050818 Max. 5 9 4,0–7,0 Matting agent for coatings and paints.

Köstropur W050618 Max. 5 6 4,0–7,0 Matting agent for coatings and paints; organic surface treatment.

Köstropur W050818 Max. 5 9 4,0–7,0 Matting agent for coatings and paints; organic surface treatment.

Depending on application all products are available with different water content and particle size.Köstropur® is a registered trademark of Chemiewerk Bad Köstritz GmbH.Market(s) served: WORLDWIDE


| 16 | BINDERS

BINDERS

BINDERS | 17 |


B WorléeCrylAcrylic Resins, solvent based, hydroxyl group containing

Type OH-contenton solids [%]

Flash pointDIN EN 22719 [°C]

Viscosity 20 °C,del.form, Brookf.,ISO 2555 [mPa·s]

Forms of delivery


W’Cryl A 1135 3,5 Appr. 23 3.000–4.000 60 % in xylene Acrylate copolymer for the manufacture of industrial coatings with very good resistance against water and other agents.

W’Cryl A 1218 1,8 Appr. 26 5.000–7.000 50 % in BAc 98/100

High reactivity and long pot life. For fast drying wood and furniture lacquers. CAB compatible.


Acrylate copolymer for the manufacture of high quality plastic coatings.


For high quality wood and furniture lacquers, good initial drying.

W’Cryl A 2116 1,6 Appr. 47 2.000–2.500 60 % in arom. HC 155–180

For fast drying industrial paint with good gloss. Also for decorative paint – in combination with WorléeThix A 2125 – for effect finishes.

W’Cryl A 2130 3,0 Appr. 25 3.500–7.000 60 % in X/BAc/ arom. HC 155–180

For two component industrial paints with good mechanical propertties and high gloss with good outdoor durability.


For high quality air and forced drying paints on metal, wood and plastics.

W’Cryl A 2210 1,0 Appr. 47 17.000–22.000 60 % in arom. HC 155–180

For very fast drying primers and fillers with very good adhesion properties on different substates. Also usable as a one component system.

W’Cryl A 2218 1,8 Appr. 25 500–2.000 50 % in X/BAc (9:1)

For air and forced drying 2 pack primers, fillers & top coats with excellent adhesion on steel, aluminium and zinc.

W’Cryl A 2230 W 3,0 50–55 max. 20.000 44 % in water/ solvent blend

Water emulsified hydroxy-acrylate for the production of exterior resistant isocyanate cross-linked two component top coats with outstanding drying properties, film hardness and gloss.

W’Cryl A 2241 W 4,1 50–55 max. 25.000 45 % in water/ solvent blend

Water emulsified hydroxyacrylate for the production of isocyanate cross-linked exterior resistant two component top coats which exhibit long potlife, high gloss and good adhesion properties.

W’Cryl A 2335 3,5 25 4.000–6.000 60 % in X/BAc/ Solvesso 100 (2:1:1)

For formulating high quality air and forced drying top and clear coats. Fast hardness development and very good adhesion for different metals.

W’Cryl A 2445 4,5 Appr. 25 3.000–5.000 60 % in X/BAc/ arom. HC 155–180

For high quality industrial and machine paints; also for car repair finishes with excellent UV-stability.

Appr. 49 8.000–12.000 60 % in arom. HC 155–180

W’Cryl A 3160 6,0 25–30 2.000–3.000 60 % in BAc/MPA

Acrylate copolymer for the manufacture of high quality, especially resistant top coats.


| 18 | BINDERS

B WorléeCrylAcrylic Resins, solvent based, thermoplastic

Type Flash point DIN EN 22719 [°C]

Flow time 20 °CDIN 53211-4 [s]

Forms ofdelivery


W’Cryl L 241 Appr. 60 80–120 (40 % in isop. HC 170–200)

60 % in isop. HC 170–200

Neutral low odour acrylic resin, mainly for wall and ceiling paints, very good insu-lating coat for nicotine, chimney and water spots, for chlorine free formulations, without plasticizer.

W’Cryl L 2380 35–40 Appr. 500 mPa·s (del. form, 20 °C, ISO 2555)

50 % in dearom. HC 160–200

Physically drying thermoplastic acrylic resin for different coating systems impro-ving hardness and gloss.

W’Cryl L 2580 Appr. 68 Viscosity, 23 °C, del. form, Brook-field, ISO 2555, 3.000–7.000 mPa·s

70 % in isop. HC 170–200

Neutral, soft, low odour acrylic resin mainly used or wall and ceiling paints, low VOC. Very good insulating coat for nicotine, chimney and water spots.

W’Cryl L 2822 Appr. 40 Viscosity, Rheom. 23 °C, C60/2°, 50S-1, DIN EN ISO 3219, 5.000–10.000 mPa·s

70 % in dearom. HC 160–200

Self crosslinking thermoplastic acrylic copolymer to be used as resin of addition in low VOC industrial paints to improve drying and film surface hardness.

Appr. 23 Viscosity, 23 °C, del. form, Brook-field, ISO 2555, 8.000–10.000 mPa·s

75 % in xylene

B WorléeCrylAcrylic Resins, water based dispersions, solutions

Type Monomer Non volat. content DIN EN ISO 3251 [%]

pH value DIN 53785

Density DIN 51757[g/cm3]

MFT [°C]

viscosity 20 °C, del. form Brookfield, ISO 2555 [mPa·s]


W’Cryl 7107 Methacrylic copo-lymer emulsion

40 7,2–8,0 1,07 > 95 max. 500 As mixing component universally suitable for improving film hard-ness, sandability, blocking resistance and stackability.

W’Cryl 7120 Styrene acrylic emulsion

49 8,2–9,0 1,09 15 200–800 Corrosion inhibiting primers on different metals (e.g. iron, alumini-um), good weather resistance.


42 7,5–8,5 1,04 39 max. 1.000 Topcoats on metal, wood, plastics (PS, ABS). Also for temporary anti-corrosive primers on metal, can be combined with water thinnable alkyd resins.


42 7,5–8,5 1,04 28 max. 200 Allround emulsion for top coats on plastic, metal, wood and for corrosion inhibiting primers with very good adhesion on steel and low water absorption.

W’Cryl 7158 Styrene acrylic copolymer emul-sion

49 7,5–8,0 1,06 5 max. 500 Self-crosslinking styrene modified acrylic emulsion for primers with excellent results in corrosion protection tests.

W’Cryl 7189 Methacrylic copo-lymer emulsion

49 7,0–8,0 1,08 16 max. 200 Flexible binder for wall Fast setting, high initial

W’Cryl 7410 Pure acrylic 45 8,0–9,0 1,06 39 max. 500 Self-crosslinking acrylic polymer for the formu lation of aqueous furniture lacquers with good resistance against household che-micals.

W’Cryl 7450 Pure acrylic emulsion

45 7,0–8,0 1,06 0 max. 500 Good blocking stability, in combination with PU-dispersion wood, parquet lacquers and top coats for wood can be formulated.


55 7,0–8,0 1,06 0 max. 500 Self-crosslinking pure acrylic emulsion with high solid content for formulating block-resistant, high gloss emulsion paints with very good levelling properties. Low VOC value in pigmented top coats, solvent free formulations are possible for glazings and colourless systems.

BINDERS | 19 |


B WorléeCrylAcrylic Resins, Water Based Dispersions and Solutions for Printing Inks and OPV´s


pH value DIN 53785

Density DIN 51757 [g/cm3]

MFT [°C]

Viscosity 20°C, del. form Brookfield, ISO 2555 [mPas]


W'Cryl 8025 Acrylic resin solution 25 8,0–9,0 1,02 – 200–800 General purpose

W'Cryl 8025 M Acrylic resin solution MEA-neutralized

25 8,0–9,0 1,02 – 200–800 Solvent free pigment pastes

W'Cryl 8040 Acrylic resin solutionwater/IPA 2:1

40 8,0–9,0 1,02 – 2.500–3.000 General purpose

W'Cryl 8043 Acrylic resin solutionwater/IPA 2:1MEA-neutralized

40 8,0–9,0 1,01 – 3.000–4.000 For high pigment concentrations

W'Cryl 8060 Acrylic resin solution 40 8,0–9,0 1,04 – max. 2.000 Solvent free, high solid resin

W'Cryl 8222 Styrene copolymer dispersion 40 8,0–8,5 1,06 0 3.000–5.000 For matt overprint varnishes

B WorléeCrylAcrylic Resins, water based dispersions, solutions


pH value DIN 53785

Density DIN 51757[g/cm3]

MFT [°C]

viscosity 20 °C, del. form Brookfield, ISO 2555 [mPa·s]



55 7,0–8,0 1,06 13 max. 1000 Self-crosslinking pure acrylic emulsion for the formulation of blocking resistant, high gloss brushable paints with a low VOC-content.

W’Cryl 7520 Acrylic emulsion 50 8,5–9,0 1,05 14 1.600–2.400 For manufacturing dispersion paints for indoor and outdoor application and coloured quartz sand plaster

W’Cryl 7712 W Pure acrylic soluti-on, cationic

26 ca. 5,0 1,04 – 300–800 Filler and colourless sealants for wood. Excellent insulating against bleeding, pigmented and transparent. Nicotine insulating paints.

W’Cryl 7712 H Cationic pure acrylic solution

40 +/-1 4,0–6,0 ca. 1,03 – 5.000–8.000 Excellent suitable as binding agent for fillers respectively as colour-less or pigmented sealing primer on wood with a high content of soluble wood ingredients.

W’Cryl 8025 Pure acrylic solution

25 8,0–9,0 1,02 – 200–800 For production of roller coatings and primers on wood.

W’Cryl 7123 Acrylic, copolymer dispersion

60 ± 1 7.0–8.0 1,07 – 100–500 High flexible roof coatings, sealing compounds, adhesives. Excellent weather resistance.

W’Cryl 7126 Acrylic dispersion 62 ± 1 5.5–6.5 1,05 – 100–500 Acrylic dispersion for the formulation of colorless joint sealers.

W’Cryl CH-X-2158 Pure acrylic dispersion

~61 5,5–6,5 ~1,05 0 100–1500 Special binders for production of thermal insulating coatings based on WorléeShield technology (e.g safe-touch, anti-condensation, insluation). Easy incorporation of voluminous insulation fillers such as hydrophobic aerogels (see page 13). High elasticity (CH-X-2159 > CH-X-2158) even at low temperatures, good water resistance and adhesion to various substrates. Combination of both binders with WorléeAdd 8905 (see page 7) allows sprayable coatings, crack-free even in thick films. Optional flame retardant properties with WorléeAdd FR 5000 (see page 7).

W’Cryl CH-X-2159 Pure acrylic dispersion

~59 5,5–6,5 ~1,06 0 150–2500


| 20 | BINDERS

B WorléeCrylAcrylic Resins, Water Based Dispersions and Solutions for Printing Inks and OPV´s


pH value DIN 53785


MFT [°C]



W'Cryl 8263 Styrene acrylate dispersion DMEA-neutralized

52 8,5–9,5 1,06 0 300–800Heat resistance, high gloss

W'Cryl 8273 Styrene acrylate dispersion 45 7,5–8,5 1,06 50 max. 1.000 High gloss OPV´s

W'Cryl 8290 Styrene acrylate dispersion 45 8,0–8,5 1,07 70 400–600 High gloss, fast drying, excellent block- and water resistance

W'Cryl 8410 Alkaline soluble acrylic dispersion anionic dispersion system

40 5,0–7,0 1,06 8 max. 100 Low MFT, high flexibility, excellent adhesion

W'Cryl 8470 Acrylic resin solution DMEA-neutralized

25 8,0–9,0 1,04 – <500 Cross linkable with melamine resin

W'Cryl 8545 Acrylic dispersion 50 4,0–6,0 1,06 3 50–300 For blister lacquers

W'Cryl 8721 Acrylic resin solution 30 5,5 1,05 – 200–400 Cationic, good adhesion to plastics


B WorléeDexStarch Copolymer Dispersions for Printing Inks and OPV´s


pH value DIN 53785


MFT [°C]



W'Dex 1177 Starch copolymer dispersion 40 3,0–5,0 1,06 28 <800 Ammonia and amine free

W'Dex 1182 Starch copolymer dispersion 50 7,5–9,0 1,04 28 <300 For thin papers, ammonia and amine free


B WorléeKydAlkyd Resins, solvent based, short oil, airdrying

Type Oil [%]

Oil type Phth.anhyd.[%]

ColorDIN ISO 4630, Gardner

Acid valueDIN EN ISO 3682 [mgKOH/g]

Flow time 20 °C DIN 53211-4 [s]

Form of delivery Main uses and principal characteristics

W’Kyd AC 2550 25 Drying veg. fatty acids

17 Max. 5 (50 % in ws 135–175)

Max. 10 150–210 (50 % in ws 135–175)

60 % in ws 135–175

Acrylated alkyd resin for extremely fast drying primers and top coats.

Max. 5 (50 % in dearom. HC 140–165)

200–260 (50 % in dearom. HC 140–165)

60 % in dearom. HC 140–165


17 Max. 5 (50 % in X)

Max. 10 90–150 (50 % in X)

60 % in xylene Acrylated alkyd resin for extremely fast drying primers and top coats.

BINDERS | 21 |


B WorléeKydAlkyd Resins, solvent based, short oil, airdrying

Type Oil [%]







19 Max. 5 (50 % in X)

Max. 12 30–60 (50 % in X)

75 % in xylene Acrylated low viscous alkyd resin for high solid primers.

Max. 5 (50 % in BAc)

30–50 (50 % in BAc)

75 % in BAc

W’Kyd L 138 38 Linseed and tung oil

30 Max. 10 (50 % in X)

Max. 15 250–300 (50 % in X)

60 % in xylene Phenolic mod., for fast drying primers and top coats, putties and fillers.

W’Kyd LH 3702 38 Linseed and tung oil

25 Max. 10 (40 % in dearom. HC 160–200)

Max. 20 90–130 (40 % in dearom. HC 160–200)

50 % in dearom. HC 160–200

Dearomatic air drying base and top coats.

W’Kyd MH 38 39 Mixed fatty acids and tung oil

38 Max. 15 (50 % in X)

Max. 25 140–170 (50 % in X)

60 % in xylene Primers and top coats, good elasticity and resistance properties.

W’Kyd MH 42 42 Drying veg. fatty acids

24 Max. 15 (50 % in ws 135–175)

Max. 20 120–150 (50 % in ws 135–175)

60 % in ws 135–175

Primers and topcoats, „Laroflex“ (BASF) compatibility.

Max. 15 (50 % in dearom. HC 140–165)

50–70 (40 % in dearom. HC 140– 165)

60 % in dearom. HC 140–165

W’Kyd MH 439 39 Mixed fatty acids

32 Max. 10 (50 % in X)

Max. 25 100–130 (50 % in X)

60 % in xylene Phenolic modified, fast drying primers and top coats, „Laroflex“ (BASF) compatibility.

Max. 10 (50 % in ws 135–175/ Solv. PM)

140–170 (50 % in ws 135–175/ Solv. PM)

60 % in ws 135–175/ Solv. PM

W’Kyd S 3001 30 Drying veg. fatty acids

35 Max. 10 (50 % in X/Solv. PM 8:2)

Max. 12 20–35 (50 % in X/Solv. PM)

75 % in xylene Solv. PM (8:2)

Low viscous, fast drying alkyd resin for manufacturing low VOC industrial primers and top coats.

W’Kyd SM 340 40 Drying veg. fatty acids

30 Max. 10 (50 % in X)

Max. 20 130–170 (50 % in X)

60 % in xylene Fast drying primers and top coats, good elasticity, good resistance properties.


30 Max. 10 (50 % in X)

Max. 20 90–110 (50 % in X)

60 % in xylene Fast drying primers and paints with excellent durability. With amino resins reactive stoving eTypels with good stability. „Laroflex“ (BASF) compatibility.


40 Max. 10 (50 % in X)

Max. 15 90–110 (50 % in X)

60 % in xylene Very fast drying alkyd resin for air and forced drying primers and top coats.


38 Max. 10 (50 % in X)

Max. 15 60–80 (50 % in X)

60 % in xylene Fast drying primers and top coats, high solids, low thermoplasticity, partial „Laro-flex“ (BASF) compatibility.

W’Kyd TT 3502 35 Drying veg. fatty acids

24 Max. 15 (60 % in X)

Max. 20 60–70 (60 % in X)

80 % in xylene Low viscous, fast drying alkyd resin for low VOC industrial primers.

W’Kyd V 298 38 Drying veg. fatty acids

25 Max. 10 (40 % in ws 135–175)

Max. 20 90–130 (40 % in ws 135–175)

55 % in ws 135–175

Fast drying primers, very good elasticity and durability, dilutable with white spirit.


| 22 | BINDERS

B WorléeKydAlkyd Resins, solvent based, medium oil, airdrying

Type Oil [%]





Form of delivery

Main uses and principal characte-ristics

W’Kyd B 845 45 Special fatty acids

25 Max. 10 (40 % in Ws 145–195)

Max. 15 80–100 (40 % in Ws 145–195)

55 % in Ws 145–195

Fast drying radiator paints, automotive and machinery refinishing enamels with good gloss. Laroflex (BASF) compatibility.

Max. 10 (del. form)

5.500–8.000 mPa·s (Rheometer 20°C, C35/1°, 100 s-1)

70 % in xylene

W’Kyd B 850 U 45 Special fatty acids

17 Max. 10 (40 % in Ws 145–195)

Max.15 80–120 (40 % in Ws 145–195)

50 % in Ws 145–195/X

Extremely fast drying, urethane mo-dified, for primers and topcoats, good recoatability.

W’Kyd B 4901 49 Cotton oil 24 Max. 10 (40 % in dearomat. HC 160–200)

Max.12 60–70 (40 % in dearomat. HC 160–200)

50 % in dearomat. HC 160–200

Fast drying, for air and forced drying indus trial, vehicle and machine paints as well as dearomat. do-it yourself and radiator paints.

W’Kyd B 4901 nv 49 Cotton oil 24 Max. 10 (55 % in dearomat. HC 160–200/ Me-thoxypropanol 3/1)

Max.12 65–75 (55 % in dearomat. HC 160–200/ Me-thoxypropanol 3/1)

75 % in dearomat. HC 160–200/ Methoxypro-panol 3/1

Fast drying, for air and forced drying industrial,vehicle and machine paints as well as dearomat. do-it yourself and radiator paints.

W’Kyd BS 830 45 Special fatty acids, silicone modified

17 Max. 10 (50 % in Ws 145–195)

Max.15 55–70 (50 % in Ws 145–195)

60 % in Ws 145–195

Silicone modified alkyd resin for high quality industrial and maintenance paints with very good drying properties, high gloss retention and corrosion resistance.

Max. 10 (50 % in isop. HC 170–200

170–220 (50 % in isop. HC 170–200)

60 % in isop. HC 170– 200

Max. 10 (50 % in dearomat. HC 160–200)

120–150 (50 % in dearomat. HC 160–200)

60 % in dearo-mat. HC 160–200

W’Kyd BS 5005 50 Special veg. fatty acids

15 Max. 5 (50 % in dearomat. HC 160–200)

Max.15 25–40 (50% in dearomat. HC 160–200)


Low viscous, airdrying, silicone modified alkyd resin for industrial and house paints, low VOC.

W’Kyd BSA 5015 approx. 49

Special veg. fatty acids

Max. 5 (60% in dearomat. HC 160–200)

Max.12 40–60 85 % in dearo-mat. HC 160–200

Low viscous, air drying, especially mo-dified alkyd resin with good resistance properties for decorative and house paints, low VOC.

W’Kyd BT 5001 50 Special veg. fatty acids

24 Max. 10 (50% in dearomat. HC 160–200)



Fast drying alkyd resin for low VOC house paints and dearomatized machi-ne-, indust-rial and D.I.Y.-paints.

W’Kyd FC 555 55 Special fatty acids

16 Max. 10 (40 % in isop. HC 170–200)

Max.10 70–100 (40 % in isop. HC 170–200)

50 % in isop. HC 170–200

Fast drying, low odour and dearomatized radiator and d.i.y. paints with high gloss and good yellowing resistance.

18 Max. 10 (40 % in dearomat. HC 160-200)

35–50 (40 % in dearomat. HC 160-200)

55 % in dearo-mat. HC 160-200

W’Kyd S 351 51 Soya oil 23 Max. 10 (40 % in dearomat. HC 180–220)

Max. 15 130–170 (40 % in dearomat. HC 180-220)


White undercoatings, mat and semi gloss enamels with good flow properties.


25–35 (40 % in dearomat. HC 180–220)


BINDERS | 23 |


B WorléeKydAlkyd Resins, solvent based, medium oil, airdrying

Type Oil [%]





Form of delivery


W’Kyd S 351 nv nv 51 Soya oil 23 Max. 10 (del. form)

Max.15 9.000–16.000 mPa·s (Rheometer 20 °C, C35/1°, 100 s-1)

60 % in isop. HC 170–200

Undercoatings, silkgloss and mat ena-mels with good flow properties.

W’Kyd S 549 50 Soya oil 27 Max. 10 (40 % in Ws 145–195)

Max.15 50–65 (40 % in Ws 145–195)

55 % in Ws145–195

Fast drying automotive and machineryrefinishing enamels.

Max. 10(45 % in Ws 135–175)

100–130 (45 % in Ws 135–175)

55 % in Ws135–175

W’Kyd SO 554 55 Soya oil 15 Max. 10 (40 % in dearomat. HC 170–200)

Max.10 70–100 (40 % in isop. HC 170–200)

55 % in isop. HC 170–200

Fast drying, low odour, dearomatizedmachinery ind. and d.i.y. paints.

W’Kyd V 162 41 Specialfatty acids

28 Max. 10 (40 % in Ws 145–195)

Max. 20 40–70 (40 % in Ws 145–195)

55 % in Ws145–195/X

Extremely fast drying car refinishing,machinery and industrial paints with high gloss, good through drying.

W’Kyd V 162 nv Max. 10 (50 % in Ws 135–175)

Max. 10 130–150 (50 % in Ws 135–175)

60 % in Ws135–175

W’Kyd V 543 50 Specialfatty acids

24 Max. 10 (40 % in Ws 145–195)

Max. 15 50–70 (40 % in Ws 145–195)

55 % in Ws145–195/X

Fast drying car refinishing, machineryand industrial paints with high gloss,good through-drying.

80–120 (40 % in Ws 145–195)

55 % in Ws145–195


| 24 | BINDERS

B WorléeKydAlkyd Resins, solvent based, long oil, airdrying

Type Oil [%]





Form of delivery

Main uses and principal charac-teristics

W’Kyd AC 6030 60 Special vegetable fatty acid

Max. 5 (70 % in dearomat. HC 160-200)

Max. 10 65–105 (70 % in dearomat. HC 160-200)


Acrylated alkyd resin with good and yellowing resistance, mainly for the use in low VOC house and decorative paints.

W’Kyd B 865 65 Cotton/Soya 22 Max. 8 (50 % in Ws 45–195)

Max. 15 70–90 (50 % in Ws 145–195)

60 % in Ws 145–195

High quality house, decorative and d.i.y. paints with good flow, high gloss, good outdoor resistance.

W’Kyd B 865 nv 65 22 Max. 8 (50 % in dearomat. HC 160–200)

Max. 15 40–50 dearomat. HC 160–200)

65 % in dearomat. HC 160-200

W’Kyd B 868 68 Vegetable fatty acids


Max. 15 20–40 (50 % in dearomat. HC 160–200)


High quality gloss paints, excellent brusha-bility, gloss retention and good drying properties.

W’Kyd B 870 69 Vegetable fatty acids

21 Max. 10 (60 % in Ws 145–195)

Max. 15 60–80 (60 % in Ws 145–195)

75 % in Ws 145–195

House paints with good brushability, high film build, good flow and excellent gloss retention.

Max. 10 (60 % in isop. HC 170–200)

90–130 (60 % in isop. HC 170–200)

75 % in isop. HC 170–200

Special fatty acids Max. 10 (60 % in dearomat. HC 160–200)

60–80 (60 % in dearomat.HC 160–200)



100–125 (60 % in dearomat. HC 180–200)


W’Kyd E 55 63 Special fatty acids, urethane modified

17 Max. 10 (60 % in Ws 145–195)

Max. 10 200–300 (60 % in Ws 145–195)

70 % in Ws 145–195

In comb. with medium oil alkyds for high quality car repair finishes and industrial paints.


50–80 (55 % in dearomat. HC 160–200)


W’Kyd L 6800 68 Linseed oil 22 Max. 10 (50 % in dearomat. HC 160–200)

Max. 10 Viscosity: 4.500–6.000 mPa·s (del. form, 23 °C, DIN 53015)


Anticorrosive,d.i.y. and house paints with high film build and good flow properties.

W’Kyd L 7904 79 Linseed oil 18 Max. 10(del. form)

Max.15 Viscosity: approx. 100 % 8.000–10.000 mPa·s (20 °C, Haake Rotovisko, C 35/1, D = 250 s -1)

approx. 100 % High solid clear lacquers, wood glazings, and high solid primers.

W’Kyd L 8004 80 Linseed oil 18 Max. 10(del. form)


98–100 % Very low viscous alkyd resin for wood impregnation and wood glazings.

W’Kyd P 151 64 Special fatty acids 22 Max. 10 (80 % in Ws 145–195)

Max. 10 130–190 (80 % in Ws 145–195)

approx. 100 % Very low viscous, for high conc. pigment preparations. Very good compatibility properties.

BINDERS | 25 |


B WorléeKydAlkyd Resins, solvent based, long oil, airdrying

Type Oil [%]





Form of delivery

Main uses and principal charac-teristics

W’Kyd RS 2174 74 Special fatty acids – < 10 Max. 6 Viscosity: < 750 mPa·s (Rheometer, 20 °C, C35/1°, 250 s 1 )

solvent free Combination resin for other alkyd re sins. Improving penetration, decreasing viscosity, VOC reduction. Sole binder for wood care and coating products.

W’Kyd S 6400 hv 63 Soya oil 26 Max. 10 (50 % in dearomat. HC 160–200)

Max.12 120–150 (50 % in dearomat. HC 160– 200)


Consumer, decorative, d.i.y. and anti corrosive paints.

(50 % in dearomat.HC 180–220)

(50 % in dearomat. HC 180–220)


W’Kyd S 7304 73 Soya oil 20 Max. 8 (del. form) Max.11 Viscosity:47.000–55.000 mPa·s (20 °C, Haake Rotovisko, C 35/1, D = 50 s 1)

approx. 100 % Low viscous, air drying long oil alkyd resin for decorative and house paints, low VOC.

W’Kyd SB 6401 64 Special fatty acids 19 Max. 10 (70 % in dearomat. HC 180–220)

Max. 18 80–120 (70 % in dearomat.HC 180–220)

90 % in dearo-mat.HC 180–220

Low viscous, air drying, long oil alkyd resin for decorative and house paints, low VOC.


60–80 (70 % in dearomat.HC 160–200)

98–100 %

W’Kyd SC 965 65 Special vegetable fatty acids




High quality house paints, very good brushability, flow and levelling, high gloss.

W’Kyd SD 7003 70 Special vegetable fatty acids

– Max. 10 (60 % in dearomat. HC 160–200)

Max.15 Viscosity: 4.000–12.000 mPa·s (20 °C, Rheometer, C 35/1°, 250 s-1)


Low viscous, air drying, long oil alkyd resin for decorative and house paints, low VOC.


– < 10 (60 % in dearomat. HC 160–200)

< 15 2.000–5.000 mPa·s (20 °C, Rheometer, C35/1°, 250 s-1)


Low viscous, long oil air drying alkyd resin for the production of decorative and house paints, low VOC.

W’Kyd SD 8300 ca. 83 Special fatty acids – Max. 10 Max.15 Viscosity, Rheome-ter, 20 °C, C35/1°, 100 s-1: 3.000–5.000 mPa·s

100 % Low viscous, air drying, long oil alkyd re-sin for decorative and house paints, low VOC. Especially suitable as combination partner for other alkyd resins

W’Kyd T 7800 78 Special vegetable fatty acids

– <10 Max.15 Viscosity, Rheo-meter, 20 °C, C 35 1°, 100 s -1: 6.500 -12.000 mPa.s

approx. 100 % Low viscous, air drying, long oil alkyd resin for house paints, glazings, d.i.y. and anticorrosive paints


| 26 | BINDERS

B WorléeKydAlkyd Resins, long oil, urethane modified

Type Oil [%]





Form of delivery


W’Kyd B 865 U 62 Vegetablefatty acids

16 Max. 10 (50 % in Ws 145–195)

Max. 10 70–100 (50 % in Ws 145–195)

55 % in Ws145–195

Urethane modified, for wood varnishes,floor coatings and industrial primers andtop coats.

Max. 10 (50 % in isop. HC 170–200)

80–100 (50 % in isop. HC 170–200)

55 % in isop.HC 170–200


80–100 (50 % in dearomat. HC 180–220)



70–90 (50 % in dearomat. HC 160–200)


W’Kyd B 865 U nv 62 Vegetable fatty acids




Urethane modified, for wood varnishes, floor coatings and industrial primers and top coats.

W’Kyd S 5703 57 Soya oil fatty acid 31 Max. 5 (50 % in Ws 145–195)

Max. 10 Viscosity:5.000–7.000 mPa·s (del. form, 20 °C, DIN 53015)

55 % in Ws 145–195

Aliphatic urethane modified alkyd resin. Use as B 865 U with better yellowing resistance.


40–55 (45 % in dearomat. HC 160–200)


W’Kyd S 6003 60 Soya oil fatty acid 19 Max. 10 (40 % in dearomat. HC 160–200)

Max. 5 23–33 (40 % in dearomat.HC 160–200)


Use as B 865 U with faster drying and harder film properties.

16 Max. 10 (del. form) 2.500–3.500 mPa·s (del. form, 20 °C, DIN 53015)

50 % in isop. HC 150–180

W’Kyd S 6003 hv 59 Soya oil fatty acid 18 Max. 10 (40 % in dearomat. HC 160–200)



Use as S 6003 with even faster drying.

W’Kyd SD 6403 64 Special fatty acids 12 Max. 6 (45 % in dearomat. HC 160–200)



Special urethane modified alkyd resin with good adhesion properties e.g. for renovati-on coatings on UV parquet sealers.



Max. 15 Viscosity, Rheometer, 20 °C, C35/1°, 250 s–1: 7.000–10.000 mPa·s


Low viscous, urethane alkyd resin for decorative and house paints, low VOC. Especially suitable as combination partner to improve drying, through drying and hardness.

W’Kyd V 5241 U 81 Linseed oil Max. 10 (del. form)

Max. 3 Viscosity: 10.000–15.000 mPa·s (del. form, 20 °C, DIN 53015)

approx. 100 %

Low viscous, oil modified polyurethane for high solid environmentally friendly coating systems.

BINDERS | 27 |


B WorléeKydAlkyd Resins, solvent based, stoving/reactive/NC-combination

Type Oil [%]






W’Kyd C 628 28 Saturated fatty acids

47 Max. 10 (50 % in X)

Max. 15 40–60 (50 % in X)

70 % in xylene High quality non yellowing stoving ena-mels, NC-and PU-coatings, colourless and pigmented. OH-cont. (on solids) 2,0–2,4 %.

W’Kyd C 632 M 32 Specially modified fatty acids

37 Max. 10(50 % in BAc)

Max.18 40–60 (50 % in BAc)

65 % in butyl acetate

NC-lacquers with properties as acid curing systems but without formaldehyde. Aromatic free. Hydroxyl content (on solids) 2,7–3,3 %.


37 Max. 10 (50 % in X)

Max.15 40–60 (50 % in X)

60 % in xylene NC-lacquers with fast solvent release, good yellowing resistance and recoatability for paper and wood.


32 Max. 10 (50 % in X)

Max.15 60–80 (50 % in BAc)

80 % in BAc High quality NC-lacquers and one com-ponent acid curing finishes with high film build and fast solvent release, forwood, foil and paper.

W’Kyd C 743 hs 12 Synthet. Fett-säuren

40 Max. 10 (60 % in aromat. HC 155–180)

Max.20 40–60 (60 % in aromat. HC 155–180)

80 % in aromat. HC 155–180

High solids one component stoving paints with high reactivity and very good mechanical properties. OH-cont. (on solids) 3,0–3,6%.

W’Kyd CD 32 32 Special fatty acids 48 Max. 8 (45 % in X)

25–40 80–130 (45 % in X)

60 % in xylene In combination with suitable amino resins for very reactive primers and top coats with good storage stability. Crosslinking with isocyanate is also possible. OH content (solids) 2.6– 3.0.

W’Kyd M 932 32 Vegetable fatty acids

38 Max. 10 (40 % in X)

Max.18 40–60 (40 % in X)

60 % in xylene Stoving primers and topcoats with high reactivity and good mechanical properties. Excellent viscosity stability. Stoving cond. 100–140 °C.

W’Kyd RM 232 32 Conjug. and saturated fatty acids

37 Max. 10(50 % in X)

Max.15 100–120(50 % in X)

70 % in BAc 98/100

Acid catalysed finishes, fast curing with good elasticity and resistance, sufficient potlife. NC-compatible, isocyanatecurable

W’Kyd SH 380 38 Special fatty acids 34 Max. 10 (60 % in BAc)

Max.15 90–110(60 % in BAc)

70 % in BAc 98/100

Acid catalysed finishes, fast curing with good elasticity and resistance, sufficient potlife. NC-compatible, isocyanatecurable.

W’Kyd SM 400 34 Drying vegetable fatty acids

30 Max. 10(50 % in X)

Max.20 90–110(50 % in X)

60 % in xylene In combination with amino resins for high reactive stoving primers and top coats.

W’Kyd SM 426 26 Drying vegetable fatty acids

40 Max. 10(50 % in X)

Max.15 90–110(50 % in X)

60 % in xylene In combination with amino resins for high reactive stoving primers and top coats.

W’Kyd T 735 36 Tall oil 35 Max. 10(50 % in X)

Max.15 60–70(50 % in X)

60 % in xylene Stoving primers and topcoats with medium reactivity and good mechanical properties. Curing conditions: 10 min./160 °C or 30 min./130 °C.


| 28 | BINDERS

B WorléeThixAlkyd Resins, Acrylic Resins, solvent based, thixotropic

Type Oil [%]

Oil type Phth. anhyd. [%]

Color DIN ISO 4630, Gardner


Viscosity, 20 °Cbei Dmax=391/sDIN 53018,part 1 [mPa·s]

Form of delivery


W’Thix A 1420 2,0 % OH content

approx. 1 (del. form)

Max. 12 Thixotropic soft gel 50 % inbutyl acetate

Thixotropic, hydroxyfunctional pure acrylate for two component finishing lacquers.


Max. 1 (del. form)

1.000–2.000 50 % in xylene Thixotropic styrene acrylic for thick layer coatings and textured finishes.

W’Thix A 2242 W 4,2 % OH content

Max. 1 (del. form)

– Thixotropic gel 58 % in Water/BAc/EEP

Thixotropic water thinnable hydroxy acrylate for formulating high quality 2 component structure paints. As combination partner in aqueous 2 component top coats for improving antisagging properties.


approx. 1 (del. form)

Thixotropic soft gel 60 % in aromat. HC 155–180

Thixotropic acrylic resin which can be crosslinked with isocyanates for air and forced drying industrial paints.

W’Thix D 46 40 Max. 10 (del. form)

Max. 4 Thixotropic soft gel 50 % in xylene Thixotropic epoxy ester,air- and oven drying, for primers, industrial- and top coats, zinc dust coatings. Thixotropy is not fully degraded by temperature and polar substances.

W’Thix L 7904 79 Linseed oil 18 Max. 10 (del.form)

Max. 15 Thixotropic strong gel

94 % in xylene High solid clear lacquers,wood glazings, and high solid primers.

W’Thix L 8050 80 Linseed oilfatty acid

Max. 10 (del. form)

Max. 15 Thixotropic soft gel 100 % Thixotropic, long oil alkyd resin, mostly used for wood glazings. Useable as sole binder as well.

W’Thix MH 439 39 Specialfatty acids

32 Max. 10 (del. form)


60 % in xylene Thixotropic short oil alkyd for fast drying primers, topcoats and textured finishes. Thixotropy is not fully degraded by temperature and polar substances.

W’Thix S 2655 26 Specialvegetablefatty acids


Max. 15 Thixotropic gel 60 % in xylene Thixotropic fast drying short oil alkyd for primers, top and textured finishes, thick layer- and stoving systems. Thixotropy is not fully degraded by temperature and polar substances.

W’Thix S 6357 64 Soya oil 24 Max. 6 (del. form)

Max. 15 Thixotropic soft gel 40 % in Ws 180–210

Thixotropic long oil alkyd resin. Combination resin for house paints, wood glazings/ thicklayer. Thixotropy is not fully degraded by temperature and polar substances.

Thixotropic soft gel 40 % in dea-romat. HC 180–220

W’Thix S 6358 64 Soya oil 24 Max. 6 (del. form)

Max. 15 Thixotropic soft gel 50 % in dea-romat. HC 180–220

Pumpable thixotropic long oil alkyd combination resin for building paints, wood glazings, thick layer. Thixo-tropy is not totally degradable by temperature and polar solvents.

W’Thix S 6455 64 Soya oilfatty acid



50 % in Ws145–195

Strong thixotropic long oil alkyd for thick layer coa-tings, wood glazings and clear coatings. Temperature stable and resistant against polar solvents.

W’Thix SD 6051 60 Specialfatty acids


Max. 15 2.500–4.000(C35/1, 391/s)

55 % in dea-romat. HC 160–200

As V 747, but with improved resistanceagainst polar substances.

3.000–4.500(C35/1, 391/s)


W’Thix 670 hs 61 Special mixed fatty acids


Max. 15 Thixotropic gel 70 % in dea-romat. HC 160–200

Thixotropic long oil alkyd for primers, fillers, gloss and silk gloss coatings, low VOC.


BINDERS | 29 |


B WorléeThixAlkyd Resins, Acrylic Resins, solvent based, thixotropic

Type Oil [%]

Oil type Phth. anhyd. [%]



Viscosity, 20 °Cbei Dmax=391/sDIN 53018,part 1 [mPa·s]

Form of delivery


W’Thix V 727 63 Special mixed fatty acid


Max. 15 3.000–4.000 52 % in Ws 180–210

Thixotropic long oil alkyd for semi gloss house paints, primers, wood stains and anticorrosive paints.

4.000–6.000 52 % in isop.HC 170–200

4.200–4.800 52 % in dea-romat. HC 180–220

W’Thix V 747 64 Special fatty acids


Max. 15 5.000–7.000 52 % in iso. HC 170–200

Thixotropic long oil alkyd for primers, mat wall and silk gloss paints and thixotropic glossy decorative and protective house paints.

5.000–7.000 52 % in dea-romat. HC 180–220

W’Thix V 800 62 Special mixed fatty acid


Max. 10 Thixotropic gel 50 % in dea-romat. HC 160–200

Thixotropic, urethane modified long oil alkyd for thick layer coatings, wood glazings and lacquers. Tempera-ture stable and resistant against polar solvents.

Max. 6 (del. form)

Thixotropic soft gel 40 % in isop.HC 170–200

B WorléeSol EPU modified Alkyd Emulsions, water thinnable

Type Oil [%]

Acid value DIN EN ISO 3682 [mgKOH/g]

pH value DIN 53785

Viscosity 20 °C, del. form Brookfield, ISO 2555 [mPa·s]

Forms of delivery


W’Sol E 150 W 44 Max. 30 7,0–8,0 50–1.500 40 % in water Medium oil alkyd emulsion for high gloss decorative, DIY and indust-rial paints. Most versatile type.

W’Sol E 280 W 28 20–30 6,9–7,2 Max. 10.000 38 % in water co-solvent free

Short oil coconut modified alkyd emulsion for non-yellowing paint systems.

W’Sol E 330 W 33 15–20 7,5–8,5 Max. 10.000 42 % in water Short oil alkyd emulsion for (drier-free based) anticorrosive primers and top coats.

W’Sol E 530 W 53 Max. 38 7,0–8,5 Max. 10.000 30 % in water Medium oil alkyd emulsion for fast drying wood paints and lacquers.

W’Sol E 927 W 28 Max. 30 6,8–7,5 Max. 10.000 40 % in water Short oil alkyd emulsion for fast curing wood coatings of all types (also drier-free).

W’Sol SE 420 W 42 Max. 30 7,0–8,5 Max. 5.000 40 % in water Medium oil silicone modified alkyd emulsion for high gloss paint systems (also decorative) with excellent outdoor resistance.


| 30 | BINDERS

B WorléeSol NWAlkyd Emulsions, water thinnable

Type Oil [%]


Viscosity 20 °C, del. form Brookfield, ISO 2555 [mPa·s]

Forms of delivery

Main uses and principal characteristicsW’Sol

W’Sol NW 410 40 1,050 Max. 3.000 46 % in water Solvent free medium oil special modified alkyd emulsion for water thinnable decorativeand d.i.y. paints with good brushability, flow and filling properties. For high gloss topcoats and wood protection stains.

W’Sol NW 474 74 1,013 Max. 1.500 60 % in water Amine and co-solvent free alkyd emulsion for wood im preg nations and wood protectingpaints. Also suitable as a co-binder to improve open time and filling properties ofdecorative paints.

B WorléeSolAlkyd Resins, water thinnable, airdrying and low bake

Type Oil [%]


Acid valueDIN EN ISO 3682 [mgKOH/g



Forms of delivery Main uses and principal characteristics

W’Sol 07 A 37 Max. 10 35–45 (50 % in BG)

1,03 80–140 (50 % in BG)

75 % in BG/sec. Butanol 1:1

Air drying and low bake industrial primers and topcoats. Low viscous, very fast dust free drying, early water resistance.

W’Sol 30 Max. 15 Max. 20 (pH 4–5) (50 % in water)

1,02 50–100 (85 % in BG)

100% Water soluble modified linseed oil type. Readily reducible with water, for printing inks, as additive for latex paints, tinting and artist colours and pigment pastes.

W’Sol 31 A 90 Max. 10 (del. form)

85–105 0,99 120–200 (Lff.) Dowanol

45 % in water/ BG 80:20 Water dispersible linseed oil polymer. Readily reducible with water for in- and outdoor stains and wood preservatives. Extremely good penetration and outdoor resistance.

W’Sol 31 C 1,00 45 % in water/PnB 8:2

W’Sol 37 90 Max. 15 55–80 0,998 230 59 % in water/BG Modified linseed oil polymer for wood protection systems. Excellent penetration and weather resistance on different woods and long term elasticity.

W’Sol 61 A 30 Max. 10 (50 % in BG)

35–45 1,06 70–90 (50 % in BG)

75 % in BG/sec. Butanol 1:1

Air drying and low bake industrial primers and top coats, very fast drying, excellent corrosion resistance

W’Sol 61 E Max. 10 (50 % in BG)

35–45 1,07 50–70 (50 % in BG)

75 % in ethoxy propanol

W’Sol 61 F Max. 10 (50 % in PnB)

40–50 1,05 70–90 (50 % in PnB)

70 % in Dowanol PnB

W’Sol 61 P Max. 10 (del. form)

35–45 1,06 6.000–20.000 m·Pas (Lff. Brookfield)

60 % in water/BG/sec. butanol

61 version fully neutralized with ammonia.

W’Sol 64 E 30 Max. 10 (50 % in BG)

35–45 1,06 50–70 (50 % in BG)

75 % in ethoxy propanol For air drying and low bake industrial primers and top coats, very fast drying, good corrosion resistance.

W’Sol 65 A 30 Max. 10 (45 % in BG)

30–40 1,05 50–70 (45 % in BG)

70 % in solvent mix: BG/sec. butanol/Dowanol PnB

Air drying and low bake industrial primers and topcoats, very fast drying, early water resistance, suitable for agricultural machinery paints.

W’Sol 65 E Max. 10 (45 % in BG)

30–40 1,05 30–60(45 % in BG)

70 % in ethoxy propanol

W’Sol 68 A 32 Max. 10 (50 % in BG)

35–45 1,07 50–100 (50 % in BG)

75 % in BG Silicone modified alkyd resin for air drying andstoving systems with excellent weather, heat andhumidity resistance.

BINDERS | 31 |


B WorléeSolAlkyd Resins, water thinnable, for stoving systems

Type Oil [%]


pH-value DIN 53785


Viscosity, 20 °C, del. form Brookfield, ISO 2555 (mPa·s)

Forms of delivery


W’Sol 84 C 30 Max. 10 (del. form)

6,7–8,5 1,06 4.000–20.000 44 % in water/BG (1,0 %) (DMEA neutr.)

For waterborne stoving systems, high gloss, good mechanical properties, total cosolvent content < 1 %.

W’Sol 85 A 30 Max. 10 (del. form)

6,7–8,5 1,06 6.000–20.000 43 % in water/BG (5,5 %) (DMEA neutr.)

As WorléeSol 84, but more reactive.

W’Sol NW 521 26 – – 1,040 – 40 % in Water/Propylenegly-col/Dowanol PnB

Applications: Short oil alkyd emulsion for the production of air drying, cobalt free decorative paints.

*Viscosity max. 1.000

B WorléePolPolyester, water thinnable, oil free, saturated

Type Acid value DIN EN ISO 3682 [mgKOH/g


OH content on solids [%]


Viscosity 20 °C, del. form

Forms of delivery


W’Pol 191 45–60 Max. 10 (50 % in BG)

Approx. 4,3 1,10 45–70 s (50 % in BG, DIN 53211-4/ 20 °C

80 % in BG Branched saturated polyester resin for waterborne industrial stoving systems.

W’Pol 194 clear to slightly opaque

Approx. 3,7 1,075 < 20.000* 40 % in water + BG (2,1%)

Branched saturated polyester resin for waterborne stoving primers, fillers and top coats with low voc. pH =7,5-8,5, very reactive.

W’Pol 808 Max. 25 Max. 3 (del. form)

Approx. 7,0 1,20 15.000–25.000** (25 °C)

100 % Low viscous, with high reactivity. For amine free water based stoving paints on metal, aluminium foil, paper and plastics. Also suitable for printing inks

W’Pol V 450 Max. 15 Max. 3 (del. form)

Approx. 8,5 1,18 500–700** (25 °C)

90 % in water Similar to WorléePol 808 but higher reactivity, better stability, higher water tolerance and lower viscosity. Also suitable for printing inks.

*Brookfield, ISO 2555 **DIN 53015 [mPa·s]


| 32 | BINDERS

B WorléePolPolyester/ether-polyols, solvent free, saturated

Type Viscosity 23 °C, del. form DIN 53015 [mPa·s]

OH value DIN EN ISO 4629 [mgKOH/g]


Water content DIN 51777, Teil 1 Karl Fischer [%]


W’Pol 165 3.000–4.000 150–170 Max. 2 Max. 0,2 WorléePol 165 is a low viscous and solvent free branched polyol with ester and ether groups and is mainly used for the formulation of solvent free coatings, sealings and adhesives in combination with modified polyisocyanates.

W’Pol 230 2.500–3.500 220–240 Max. 2 Max. 0,2 WorléePol 230 is a low viscous and solvent free branched polyol with ester and ether groups and is mainly used for the formulation of solvent free coatings, sealings and adhesives in combination with modified polyisocyanates.

W’Pol 1181/03 1.700–2.700 (25 °C)

310–350 Max. 2 Max. 0,1 Saturated low viscous polyester resin, due to its wide compatibility suitable for vari-ous systems, e.g. as modifying component for solvent and water based isocyanate and amino resin crosslinking coatings to improve flexibility, flow, chemical and me-chanical resistance and to increase solids content. Corresponds to FDA § 175.300.

W’Pol 1181/09 1.500–3.000 (25 °C)

310–350 Max. 2 Max. 0,1 Saturated low viscous polyester resin, due to its wide compatibility suitable for various systems, e.g. as modifying component for solvent and water based isocya-nate and amino resin crosslinking coatings to improve flexibility, flow, chemical and mechanical resistance and to increase solids content. Excellent weather resistance.

B WorléePolPolyester, solvent based, saturated

Type OH con-tent on solids [%] approx.



Color DINISO 4630,Gardner

Forms of delivery Main uses and principal characteristics

W’Pol 6631 8,0 20.000–30.000 mPa·s (Lff, Brookfield, ISO 2555)

Max. 3 Max. 3 67 % in methoxy propyl acetate

Saturated type for air drying two pack PU coatings.


– Max. 2 80 % in BAc Saturated, hydroxy functional polyester resin for the manufacture of solvent based „ultra high solids“ two component PUR systems.


– Max. 2 78 % in BAc Saturated, hydroxy functional polyester resin for the manufacture of solvent based „ultra high solids“ two component PUR systems for industrial and car repair coatings with good mechanical properties and excellent chemical and weather resistance.

BINDERS | 33 |


B WorléeRes EPolyesterpolyols, solvent based and solvent free, saturated

Type Delivery Form [%]

Viscosity [mPa.s/23°C]

Acid Value [mg KOH/g]

OH-Value[mg KOH/g]

Main uses and principal characteristics Type

W'Res E 1865 65 % in S1/IBU

2.400–3.000 ≤ 5,5 75–90 Oil-free, saturated, polyester resin especially for baking coatings, can- and coil coatings. Corresponds to FDA 21.CFR § 175.300.

B

W'Res E 1842 60 % in S2/MPA

4.500–6.500 ≤ 4 30–40 Oil-free, saturated polyester resin for highly flexible baking coatings, can- and coil coatings (top-coat) and general industrial coatings.

L

W'Res E 1845 65 % in S1/IBU

1.000–1.600 ≤ 5 70–80 Oil-free, saturated, branched polyester resin for baking coatings, can- and coil coatings for food packaging and automotive primers surfacers. Corresponds to FDA 21.CFR § 175.300.

B

W'Res E 1851 50 % in S2/S4

2.000–4.000 ≤ 3 15–25 Oil-free, saturated linear, polyester resin for baking coatings, can- and coil coatings (top-coat) and general industrial coatings.

L

W'Res E 1805 65 % in MPA

17.000–23.000 ≤ 3 262–285 Low branched saturated polyester resin. For air- and oven drying two component polyurethane coatings with excellent weather stability.

SB

W'Res E 1844 60 % in S2/BG

3.000–4.500 ≤ 8 45–60 Saturated linear, polyester resin for baking coatings, can- and coil coatings (top-coat) and general industrial coatings.

B

W'Res E 1860 70 % in S2/PMA/BG

3.500–4.900 ≤ 12 110–120 Saturated polyester resin. For highly elastic, weather stable baking coatings and coil coatings (backing coat).

B

W'Res E 1861 66 % in S2/BG

1.400–2.100 ≤ 12 75–85 Oil-free branched, polyester resin with low molecular weight for bakings coatings, can- and coil coatings (top-coat) and general industrial coatings.

B

W'Res E 1862 66 % in S2/S4/PMA/BG

1.600–2.300 ≤ 12 75–85 Oil-free branched, polyester resin with low molecular weight for bakings coatings, can- and coil coatings (top-coat) and general industrial coatings.

B

W'Res E 1870 80 % in BA

2.600–3.500 ≤ 3 132–156 Low branched, saturated polyester resin for elastic high solid, two component polyurethane coatings. For industrial coatings, automotive repair coatings and plastic coatings.

SB

W'Res E 1800 solvent-free 25.000–36.000 ≤ 3 200–230 Solvent free, branched polyester resin. For air- and stove-drying flexible two-com-ponent polyurethane coatings based on aliphatic and aromatic Isocyanates.

BP

B WorléeDurEpoxy Esters, drying

Type Oil[%]

Oil type EP-resin[%]

Color DIN ISO 4630,Gardner

Acid valueDIN ENISO 3682[mgKOH/g]

Flow time 20 °CDIN 53211-4[s]

Forms ofdelivery


W’Dur D 46 40 Conj. fattyacids

60 Max. 10 (50 % in X)

Max. 4 200–250 (50 % in X)

60 % in xylene High quality zinc rich and anti corrosive paints, airdrying and stoving primers and top coats, fast drying and excellent water resistance.

W’Dur MF 45 40 Tall oil/tung oil

60 Max. 20 (50 % in X)

Max. 6 200–250 (50 % in X)

60 % in xylene Zinc rich and anti corrosive paints with excellent wa-ter resistant and rust preventing, good brushability.

W’Dur D 6311 63 Specialmodified

Max. 10 (del. form)

Max. 2 3.000–4.000 mPa·s (del. form, 20°C, DIN 53015)3.500–5.000

60 % in dearomat.HC 140–165

Universal adhesion and anti corrosion primer and one coat paints. Very good adhesion even on difficult substrates.

60 % in white spirits 145–195



| 34 | BINDERS

B WorléeCureSpecial hardeners for epoxy resins, free of Nonylphenol

Type Viscosity 20 °C [mPas]

Amine Value [mg KOH/g]

Color Gardner

H-equiva-lent

Medium potlife Main uses and principal characteristics

W’Cure H 60 50–100 350–450 max. 2 90 approx. 25 min. Modified polycondensated polyamine system for self-levelling floorings, very good levelling and deairating, properties, though and resilient.

W’Cure H 90 175–325 325–425 max. 4 90 approx. 40 min. Modified cycloaliphatic polyamine adduct for self-levelling floorings, good levelling properties, low carbamation

W’Cure H 100 300–600 625–775 max. 2 50 approx. 50 min. Polycondensated polyamine free of benzylic alcohol. Special hardener system for modification of standard hardeners.

W’Cure CA 235 450–750 260–340 max. 2 104 approx. 18 min. Modified cycloaliphatic polyamine adduct. Low-viscous hardener for ambient curing solvent-free self-levelling floorings and adhesives.

W’Cure CA 243 250–450 250–350 max. 2 115 approx. 50 min. Low viscous, solvent free hardener system based on a cycloaliphatic polyamine adduct. For solvent free epoxy flooring systems.

W’Cure CA 246 130–250 250–350 max. 2 93 approx. 30 min. Modified cycloaliphatic polyamine adduct. Universal hardener for casting, solvent-free laminates, coating systems, adhesives, mortars and primers.

W’Cure CA 250 280–400 250–350 max. 2 94 approx. 40 min. Modified cycloaliphatic polyamine adduct. Low yellowing upon UV-exposure, therefore suitable for aesthetically demanding coatings, e.g. mortars and top-coats.

W’Cure H 86 W 3.000–5.000 280–380 max. 2 86 approx. 30 min. Low viscous, water thinnable Epoxy-hardener based on a polyamine adduct. For sealings and self-levelling coating systems.

W’Cure CA 240 S 300–400 250–350 max. 2 93 approx. 25 min. Accelerated modified cycloaliphatic polyamine adduct for solvent-free self-levelling epoxy systems.

B WorléeFenRosin based hard resins, phenol modified

Type Melting point Capillary method[°C]



ColorDIN ISO 4630, Gard-ner

M.O.T. [%] Main uses and principal characteristics

W’Fen F 105 90–110 15–25 20–30 (50 % in Ws 145–195)

Max. 10 (50 % in Ws 145–195)

300 General purpose type for alkyd based paints and primers. Low viscous resin giving excellent gloss and rub resistance on cold set inks.

W’Fen F 120 110–130 10–20 80–120 (50 % in Ws 145–195)

Max. 10 (50 % in Ws 145–195)

225 General purpose type for alkyd based paints and primers and for cooking with alkyds. Fast setting, high gloss resin for sheetfed inks. Compatible with alkyds and natural inks.

W’Fen F 130 120–140 15–25 120–170 (60 % in X)

Max. 10 (60 % in X)

– Cold cut modifying resin for paints with good drying properties and high gloss.

BINDERS | 35 |


B WorléeSinRosin based maleic resins and rosin esters

Type Melting point Capil-lary method [°C]





W’Sin GM 201 95–120 20–25 25–50 (50 % in Ws 145–195)

Max. 8 (50 % in Ws 145–195)

General purpose resin for modification of oil, alkyds and paints based up on them. As a cold cut or to be polymerised with oils and alkyds.

W’Sin GM 203 100–125 20–25 25–50 (50 % in Ws 145–195)

Max. 8 (50 % in Ws 145–195)

General purpose resin for oil and alkyd based paints and for NC-lacquers. For modification of oil and paints based up on them. As a cold cut or to be polymerised with oils and alkyds.

W’Sin PM 200 95–115 15–25 20–40 (50 % in Ws 145–195)

Max. 8 (50 % in Ws 145–195)

Low viscosity penta esterified resin for gloss improvement for house and industrial paints and dispersing media for pigment pastes and preparations.

W’Sin PM 202 100–125 15–20 30–60 (50 % in Ws 145–195)

Max. 8 (50 % in Ws 145–195)

Penta esterified general purpose resin for decorative, do-it-yourself and industrial paints. Also used for furniture adhesives.

W’Sin MK 223 90–110 40–50 80–120 (60 % in BAc)

Max. 8 (60 % in BAc)

With castor oil plasticized, for NC-lacquers with very good solvent release and sandability.

W’Sin MS 235 125–155 180–200 10–20 (50 % in ethanol)

Max. 15 (50 % in ethanol)

For alcohol and water based paints and lacquers, flexo and gravure inks, overprint varnishes. Com-patible with acrylic polymers and NC. Soluble in water after neutralisation. FDA 175.105, 175.300

W’Sin MS 265 155–190 190–220 15–25 (50 % in ethanol)

Max. 8 For alcohol and water based paints and lacquers, flexo and gravure inks, overprint varnishes. Com-patible with acrylic polymers and NC. Soluble in water after neutralization. FDA 175.105, 175.300

B WorléeGilsolNatural Asphaltum Solutions

Type Non volatile content DIN EN ISO 3251 [~%]

Solvent Viscosity Brookfield-Rheometer, Spindel CP52 (Kegel-Platte) 25°C, 75rpm [mpa.s]

Flow Time 20°C DIN 53211-4 [s]


Gilsol 30 T ca. 30 White spirit/DPM

500–1100 Wood protection and black paints

Gilsol 40 X ca. 40 Xylene 40–70 Wood protection and black paints


| 36 | BINDERS

B WorléeGumNatural Resins

Type SofteningPoint [°C]

Acid Value DIN EN ISO 3682 [mgKOH/g]

SaponificationDIN EN ISO 3681 [mgKOH/g]

Color DINISO 4630,Gardner

Forms ofdelivery


Dammar white 5200

80–90 20–30 35–60 3–5 big lumps In combination with oils and alkyds for for solvent based rotogravureinks with high gloss and good adhesion on plastic films.

Dammar white 5202

80–90 20–30 35–60 3–5 small lumps In combination with oils and alkyds for for solvent based rotogravureinks with high gloss and good adhesion on plastic films.

Copal 5001 100–120 100–120 145–190 3–6 big lumps In combination with other binders for food and paper fishing,floor lacquers and adhesives.


Type Wax[%]

MeltingPoint [°C]

Acid Value DIN EN ISO 3682 [mgKOH/g]

SaponificationDIN EN ISO 3681 [mgKOH/g]

Color Gardner20 % inEthanol

Forms ofdelivery


Shellac 4621 dewaxed ≤ 0,2 65–85 65–80 190–230 Max. 10 Flakes For wood and paper finishing, French polish, coatings and adhesives. Excellent binder for packing material printing inks with good adhesion on plastic.

Shellac 4624 DL dewaxed ≤ 0,2 65–85 65–80 190–230 Max. 15 Flakes

Shellac 4625 DO dewaxed ≤ 0,2 65–85 65–80 190–230 Max. 16 Flakes

Shellac 4503 lemon 1 h.m. waxed ≤ 5,5 70–90 65–76 185–200 Max. 16 Flakes For wood and paper finishing, French polish, coatings and adhesives. Makes it possible to produce high solid, quick drying, waterproof printing inks and overprint varnish.

Shellac 4504 lemon 1 m.m. waxed ≤ 4,5 70–90 60–80 185–220 Max. 18 Flakes

Shellac 4505 TN waxed ≤ 4,5 70–90 60–80 185–220 Max. 18 Flakes

Shellac 4602 waxed ≤ 4,5 70–90 60–80 185–220 Max. 16 Flakes

B WorléeGumShellac Solutions

Type Solid Content [approx.%] pH value Viscosity [mPa·s] Max.

Forms of delivery

Yello

wis

h-or

ange

coul

oure

d so

lutio

n W’7730 SOLW 25–27 approx. 7,9 212 approx. 25% white bleached Shellac in aqueous potassium hydroxide solution

W’7730 SOLL 49 – 390 approx. 49% white bleached Shellac (dewaxed) in ethanol

W’4621 SOLW 30 7,0–7,5 200 approx. 30% Shellac (dewaxed) dissolved in aqueous potassium hydroxide solution

W’4621 SOLL 50 – 1.000 approx. 50% Shellac (dewaxed) in ethanol

Dark

sol

utio

n

W’4624 SOLW 25 7,5–8,0 1.000 approx. 25% Shellac DL in aqueous potassium hydroxide solution

W’4625 SOLW 25 7,5–8,0 500 approx. 25% Shellac DO (dewaxed) dissolved in aqueous potassium hydroxide solution

W’4625 SOLL 50 – 1000 approx. 50% Shellac DO (dewaxed) in ethanol

W’4505 SOLW 29–31 7,0–7,5 200 approx. 30% Shellac (wax containing) dissolved in aqueous potassium hydroxide solution

W’4505 SOLL 45 – 2.000 approx. 45% Shellac (wax containing) in ethanol


BINDERS | 37 |


B WorléeProtectInorganic-organic hybrid systems

Type Appearance Forms of delivery Application Main uses and principal characteristics

W'Protect 1507 Clear, slightly yellowish liquid 42% in ethanol Spraying, dip-ping, flooding, wiping

Thin layer clear coat with excellent anti graffiti- / easy-to-clean-effect on glass, metals, old paint layers (grind by using an abrasive pad). Drying at room temperature, forced or by stoving.

W'Protect 1519 Clear, slightly yellowish liquid 42% in n-propanol Spraying, dip-ping, flooding, wiping

W'Protect 1581 Clear liquid 30% in Solvenon DMP / 1-M-2P Spraying, dip-ping, flooding, wiping

Two component thin layer clear coat with W´Protect 1519 / 1507. Used with catalysts as a sole binder. High abrasion- and scratch resistance, good chemical resistance, excellent mar resistance and anti graffiti- / easy-to-clean-effect.

B WorléeCopStyrene-Butadiene-Copolymer

Type Solids Viscosity[°C]

pH value [mPa·s]

Main uses and physical properties

W’Cop 100 50.0 ± 1.0 50–400 8.0–8.6 Binding agent in aqueous anticorrosive automotive coatings where resistance against pebble/ gravel is requi-red, often in combination with water soluble or water thinnable resins


B ZinpolAcrylic Resins, Water Based Dispersions and Solutions for Printing Inks and OPV´s


pH value DIN 53785


MFT [°C]



Zinpol 132 Styrene acrylate dispersion 40 8,0–9,0 1,05 56 5.000–6.000 Metallic printing inks

Zinpol 146 Acrylic solution 35 7,0–7,5 1,06 <0 2.500–3.000 Metallic printing inks, excellent ink stability

Zinpol 259 S Shellac supported polystyrene dispersion

49 8,0–8,5 1,05 >100 200–800 High gloss

Zinpol 280 Styrene acrylate dispersion 47 8,5–9,0 1,04 <0 800–1500 Good adhesion on nonporous subst-rates, paper, paperboard and foils

Zinpol 295 Acrylate dispersion 49 8,0–9,0 1,05 5 1.250–2.750 Ice water crinkle resistance

Zinpol 330 Styrene acrylate dispersion 46 8,0–8,5 1,04 12 1.500–2.500 Excellent grease and oil resistance

Zinpol 340 Styrene acrylate dispersion 44 8,0–9,0 1,08 75 500–1.000 High gloss, heat resistance

Zinpol 350 Styrene acrylate dispersion 45 8,0–9,0 1,06 0 300–800 Excellent high gloss dispersion

Zinpol 387 Styrene acrylate dispersion 50 8,0–9,0 1,04 65 300–700 No crinkles on thin paper

Zinpol 460 Styrene acrylate dispersion 50 8,0–8,5 1,06 75 200–600 Fast drying, high film hardness


| 38 | BINDERS

B ZinpolAcrylic Resins, Water Based Dispersions and Solutions for Printing Inks and OPV´s


pH value DIN 53785


MFT [°C]



Zinpol 520 AS-D Colloidal pure acrylic solution 20 9,5–10,0 1,05 2.000–3.000 For carbon black pigments

Zinpol 755 Styrene acrylate dispersion 41 8,0–9,0 1,06 0 200–600 Heat resistance up to 240°C

Zinpol 790 Styrene acrylate dispersion 45 7,5–8,5 1,15 5 1.500–2.500 Fast drying, ice water resistance, flexible

Zinpol 797 Acrylate dispersion 48 8,0–8,5 1,05 0 500–1.000 Anti slip


B polyols & polymersKetone Aldehyde Resins

Type Melting Point [°C]

Viscosity at 25 °C; 50 % solution alcohol; B-4 FC in sec. [cPs]

Acid Value [Max.]

Hydroxyl Value [mg Koh/g resin]

Iodin No. of 50 % solution alcohol [Max.]


Polytone K-93 98–103 15–17 0,01 265–285 1 Lamination inks, lacquers and paper coatings

Polytone K-94 90–95 17–19 0,1 200–220 1 Flexo- and gravure printing inks, ball point inks




Market(s) served: WORLDWIDE, EXCEPT MIDDLE EAST AND INDIA

B Bruno Bock – Thiocure® PolythioleVOC-free Polythiols- multifunctional mercapto compounds based on mercaptocarboxylic acids

Type Chemical description

SH-func-tionality

Molecular weight [g/mol]

H-active Equivalent [g/mol]

SH-content [%]

Viscosity [mPas]

Applications and characteristics

Thiocure® PETMP Pentaerythritol-tetra(3-mercaptopropionate)

4 488,6 125–128 26 ~400 Standardtype for solvent and solvent-free systems. Reacts with Epoxy, Isocyanate and unsaturated compounds.Useable as a high reactive hardener for Epoxy-systems to enhance the curing speed even at low temperatures. Additive for fast curing in high-solid PU-systems. Binder for Thiourethane-systems and Thiol-Ene-systems (thermal or UV-curing).Additive for radiation curing systems, to reduce the oxygen inhibition, volume shrinkage and to increase the hardening speed. Additive for polysulfide sealants to increase the crosslink density.

Thiocure® PETMP l.o.

Pentaerythritol-tetra(3-mercaptopropionate), low odor

4 488,6 125–128 26 ~400 odor-optimized version of the standardtype Thiocure® PETMP


BINDERS | 39 |

B Bruno Bock – Thiocure® PolythioleVOC-free Polythiols- multifunctional mercapto compounds based on mercaptocarboxylic acids

Type Chemical description

SH-func-tionality

Molecular weight [g/mol]

H-active Equivalent [g/mol]

SH-content [%]

Viscosity [mPas]

Applications and characteristics

Thiocure® PETMP sl

Pentaerythritol-tetra(3-mercaptopropionate), slow

4 488,6 125–128 26 ~400 controlled reactivity, recommended for Isocyanate curing systems.

Thiocure® TMPMP

Trimethylolpropane-tri(3-mercaptopropionate)

3 398,6 136–140 24 ~150 trifunctional Polythiol, more flexible than Thiocure® PETMP because of lower crosslink density.

Thiocure® GDMP

Glycol-di(3-mercaptop-ropionate)

2 238,3 122–125 26,8 ~10 difunctional Polythiol, more flexible than Thiocure® PETMP and Thiocure® TMPMP because of lower crosslink density.

Thiocure® PETMA

Pentaerythritol-tetra-mercaptoacetate

4 432,5 111–114 29 ~400

Mercaptoacetates, compared to Mercaptopropionates (Thiocure® PETMP/ TMPMP/ GDMP) more reactive but intensive odor.

Thiocure® TMPMA

Trimethylolpropane-tri(3-mercaptopropionate)

3 356,5 122–125 26,5 ~120

Thiocure® GDMA

Glycol-dimercaptoace-tate

2 210,2 107–108 30,5 ~10

Thiocure® ETTMP 1300

Ethoxylated Trimethylol-propane-tri(3-mercapto-propionate)

3 1.300 435–448 7,1 ~400 Polymer-Polythiol, compared to Thiocure® PETMP/ TMPMP/ GDMP soft and flexible but less reactive

Thiocure® ETTMP 700

Ethoxylated Trimethylol-propane-tri(3-mercapto-propionate)

3 708 236–262 13,5 ~200 Polymer-Polythiol, compared to Thiocure® ETTMP 1300 less flexible but higher mechanical strength

Thiocure® TEMPIC

Tris[2-(3-mercapto-propionyloxy)ethyl] isocyanurat

3 525,6 180–184 18,4 ~8.000 Trifunctional Polythiol based on isocyanurate structure. Improved adhesi-on to metallic substrates and excellent reactivity in thiol-Ene systems

Thiocure® Di-PETMP

Di-Pentaerythritol Hexa(3-mercaptopro-pionate)

6 783,1 135–140 24,1 ~2.000 Hexafunctional Polythiol, higher crosslink density, harder and higher glass transition temperatures

Thiocure® PCL4MP 1350

Polycaprolactone Tetra (3-mercaptopropionate)

4 ~1350 348–375 9,1 ~1.000 Polymer-Thiol based on Polycaprolactone, compared to Thiocure® ETTMP 700 more reactive and flexible, better moisture- and UV-resistance

Market(s) served: GERMANY, AUSTRIA, SWITZERLAND, ITALY, FRANCE, SPAIN, POLAND, CZECH REPUBLIC, HUNGARY, ROMANIA, SLOVAKIA, CHINA, INDIA, MALAYSIA, SINGAPORE, VIETNAM, THAILAND, INDONESIA

B AGCNatural Asphaltum

Type Softening pointASTM E28-92 [°C]

Ash [%] Color Form of Delivery Main uses and principal characteristics

Gilsonite® Selects 347

159–174 Max. 0,9 Dark brown to black

Small lumps Grinding resin for carbon black based news and heatset inks

Market(s) served: AUSTRIA, CENTRAL, EASTERN AND SOUTHEASTERN EUROPE, FINLAND, GERMANY, SWEDEN


COLOR

| 40 | COLOR


C WorléeTransoxid WWater based iron oxide, carbon black and titanium dioxide preparations for wood stains

Product Name C.I. Pigment content % (approx.)

pH-value (approx.)

VOC g/l (approx.)

Density g/cm³ (approx.)

Viscosity mPa.s ca.

Applications and Properties

W'Transoxid W red PR 101 40 8–10 < 50 1,45 Approx. 600 Transparent, water based iron oxide preparations and carbon black pastes for wood stainsW'Transoxid W yellow PY 42 40 8–10 < 50 1,43 400–800

W'Blackpaste W PBI 7 40 7,5–9 < 5 1,21 Approx. 1.500

C WorléePaste S-AKSolvent based pigment preparations for wood stains


VOC g/l (approx.)


Viscosity mPa.s (approx.)


W'Paste S-AK 412 PV 23 20,0 ± 1 510 0,91 1.500 Solvent based pigment preparations for the woodstain area

W'Paste S-AK 512 PB 15:2 20,0 ± 1 512 0,91 1.500

W'Paste S-AK 610 PG 7 20,0 ± 2 475 0,96 1.800

C WorléeTransoxid SSolvent based transparent iron oxide, carbon black and titanium dioxide preparations for wood stains


VOC g/l (approx.)


Viscosity mPas (approx.)


W'Transoxid S red PR 101 39,0 ± 1 430–450 1,31 400–800 Transparent, solvent based iron oxide and carbonblack preparations for wood stains

W'Transoxid S yellow PY 42 39,0 ± 1 430–450 1,27 300–800

W'Blackpaste S PBI 7 25,0 ± 2 420–440 1,01 500–1500

W'Whitepaste S PW 6 65,0 ± 2 ca. 430 1,7 Approx. 1.000

COLOR | 41 |


| 42 | COLOR

C WorléeQuarzsand ASElectroconductive Quartz

Typ Color Electrical resistance [Ohm] Particle size [mm]

W’Quarzsand AS 0104 Black < 500 0,1–0,4




C WorléeTransoxid SF-AKTransparent pigment preparations based on solvent free binders for wood stains



Viscosity mPas (approx.)


W'Transoxid SF-AK Red PR 101 30 1,06 1.200 Transparent iron oxide and carbon black preparations based on solvent free binders for wood stains

W'Transoxid SF-AK Yellow P.Y. 42 30 1,06 2.800

W'Blackpaste SF-AK PG 7 15 1 1.500

| 42 | COLOR


COLOR | 43 |

C CabotCarbon Black

Type Deliv

ery

form

tintin

g st

reng

th

Unde

rtone

(hig

her =

blu

er)

visc

osity

Disp

ersi

bilit

y

elec

tr.

Cond

uctiv

ity

lacq

uers

&

Pain

ts

oem

/car

repa

ir

Plas

tic

mas

terb

atch

Prin

ting

inks

emul

sion

Uv-c

urin

g

REGU

LAR

Colo

r BLA

CK

BLACK PEARLS 120 Pearls 1 5 1 3 0 ■ ■ ■ ■ ■

MONARCH 120 Powder 1 5 1 3 0 ■ ■ ■ ■ ■

BLACK PEARLS 160 Pearls 2 5 1 4 0 ■ ■■ ■■ ■ ■

BLACK PEARLS 280 Pearls 2 4 2 5 0 ■■■ ■■ ■■ ■■ ■■

MONARCH 280 Powder 2 4 2 5 0 ■■■ ■■ ■■ ■■ ■■

ELFTEX 430 Pearls 3 3 3 1 0 ■■■ ■■■ ■■■ ■■■ ■■■

MONARCH 430 Powder 3 3 3 1 0 ■■■ ■■■ ■■■ ■■■ ■■■

ELFTEX 460 Pearls 3 3 3 2 0 ■■ ■■ ■■ ■■■ ■■■

BLACK PEARLS 470 Pearls 4 3 3 3 0 ■■ ■■ ■■ ■■ ■■

MONARCH 480 Powder 4 3 3 3 0 ■■ ■■ ■■ ■■ ■■

BLACK PEARLS 490 Pearls 4 2 4 4 0 ■■■ ■■ ■■ ■■ ■■

MONARCH 490 Powder 4 2 4 4 0 ■■■ ■■ ■■ ■■ ■■

ELFTEX 570 Pearls 5 2 4 3 0 ■■ ■ ■ ■■■ ■■

MONARCH 570 Powder 5 2 4 3 0 ■■ ■ ■ ■■■ ■■

ELFTEX 580 Pearls 5 1 5 3 0 ■■ ■ ■ ■■■ ■■

MONARCH 580 Powder 5 1 5 3 0 ■■ ■ ■ ■■■ ■■

SPEC

IALI

TY C

olor

ELFTEX 220 Pearls 1 5 1 3 0 ■■■ ■■ ■ ■■■ ■■■

REGAL 350 R Powder 1 5 1 3 0 ■■■ ■■ ■ ■■■ ■■■

ELFTEX 320 Pearls 2 4 2 2 0 ■■■ ■■ ■ ■■■ ■■■

REGAL 250 R Powder 2 4 2 2 0 ■■■ ■■ ■ ■■■ ■■■

BLACK PEARLS E* Pearls 3 5 1 5 0 ■■■ ■ ■ ■■■ ■ ■■■

MOGUL E* Powder 3 5 1 5 0 ■■■ ■ ■ ■■■ ■ ■■■

ELFTEX 410 Pearls 4 1 5 1 0 ■■ ■■ ■■ ■■■ ■■

ELFTEX 415 Powder 4 1 5 1 0 ■■ ■■ ■■ ■■■ ■■

REGAL 400* Pearls 4 4 2 5 0 ■■ ■ ■ ■■■ ■■■ ■■■

REGAL 400 R* Powder 4 4 2 5 0 ■■ ■ ■ ■■■ ■■■ ■■■

BLACK PEARLS L* Pearls 5 3 3 4 0 ■■■ ■■ ■■ ■■■ ■■■ ■■

MOGUL L* Powder 5 3 3 4 0 ■■■ ■■ ■■ ■■■ ■■■ ■■

1 bad/weak ■■■ highly recommendable ■ on consultation5 very good/strong ■■ recommendable * volatile matter: >3,5 Vol.%Evaluation only within the groups mentioned.BLACK PEARLS®, ELFTEX®, MOGUL®, MONARCH®, VULCAN®, REGAL® and EMPEROR® are registered trademarks of the Cabot Corporation.Market(s) served: CZECH REPUBLIC/SLOVAKIA, GERMANY, POLAND, ROMANIA


| 44 | COLOR

C CabotCarbon Black

Type Deliv

ery

form

tintin

g st

reng

th

Unde

rtone

(hig

her =

blu

er)

visc

osity

Disp

ersi

bilit

y

elec

tr.

Cond

uctiv

ity

lacq

uers

&

Pain

ts

oem

/car

repa

ir

Plas

tic

mas

terb

atch

Prin

ting

inks

emul

sion

Uv-c

urin

g

MED

IUM

Col

or

REGAL 660 Pearls 1 5 1 5 0 ■ ■ ■ ■ ■

REGAL 660 R Powder 1 5 1 5 0 ■ ■ ■ ■ ■

BLACK PEARLS 700 Pearls 2 4 4 4 0 ■ ■■ ■■ ■ ■

MONARCH 700 Powder 2 4 4 4 0 ■ ■■ ■■ ■ ■

BLACK PEARLS 800 Pearls 3 3 2 2 0 ■■ ■■ ■■ ■ ■

MONARCH 800 Powder 3 3 2 2 0 ■■ ■■ ■■ ■ ■

BLACK PEARLS 880 Pearls 4 2 5 3 0 ■■ ■■■ ■■■ ■ ■

MONARCH 880 Powder 4 2 3 0 0 ■■ ■■■ ■■■ ■ ■

BLACK PEARLS 900 Pearls 5 1 3 1 0 ■■ ■■■ ■■■ ■ ■

MONARCH 900 Powder 5 1 3 1 0 ■■ ■■■ ■■■ ■ ■

HIGH

Col

or

BLACK PEARLS 1000* Pearls 5 2 4 3 0 ■■ ■■ ■■ ■ ■ ■

MONARCH 1000* Powder 5 2 4 3 0 ■■ ■■ ■■ ■ ■ ■

BLACK PEARLS 1100 Pearls 5 2 4 3 0 ■■ ■■ ■■ ■ ■ ■

MONARCH 1100 Powder 5 2 4 3 0 ■■ ■■ ■■ ■ ■ ■

BLACK PEARLS 1300* Pearls 3 3 3 2 0 ■■ ■■■ ■■ ■ ■ ■

MONARCH 1300* Powder 3 3 3 2 0 ■■ ■■■ ■■ ■ ■ ■

BLACK PEARLS 1400* Pearls 3 4 2 2 0 ■■ ■■■ ■■ ■ ■ ■

MONARCH 1400* Powder 3 4 2 2 0 ■■ ■■■ ■■ ■ ■ ■

MONARCH 1500* Powder 3 5 1 2 0 ■■ ■■■ ■■ ■ ■ ■

EMPEROR 1200 Pearls 4 5 5 5 0 ■■■ ■■■ ■■ ■

EMPEROR 1600 Pearls 4 4 5 5 0 ■■■ ■■■ ■■ ■

EMPEROR 1800* Powder 4 5 5 5 0 ■■ ■■■ ■

EMPEROR 2000* Powder 4 5 5 5 0 ■■ ■■■ ■

Market(s) served: CZECH REPUBLIC/SLOVAKIA, GERMANY, POLAND, ROMANIA

COLOR | 45 |


C IshiharaTitanium Dioxide

Type Pigment Production Process

TiO2 content [%] Surface treat-ment


Tipaque R-980 Rutile Sulfate 93 Al2O3, Polyol Excellent resistance, very high hiding power and Color fastness and easy to disperse

Market(s) served: CENTRAL, EASTERN AND SOUTHEASTERN EUROPE, GERMANY

C CabotCarbon Black

Type Deliv

ery

form

tintin

g st

reng

th

Unde

rtone

(hig

her =

blu

er)

visc

osity

Disp

ersi

bilit

y

elec

tr.

Cond

uctiv

ity

lacq

uers

&

Pain

ts

oem

/car

repa

ir

Plas

tic

mas

terb

atch

Prin

ting

inks

emul

sion

Uv-c

urin

g

CON

DUCT

IVE

ELFTEX TP Pearls 2 3 3 3 1 ■ ■■■ ■■■ ■ ■

ELFTEX 254 Pearls 3 3 3 2 2 ■■ ■■■ ■■■ ■ ■■

VULCAN XC 305 Pearls 1 5 1 5 3 ■ ■■ ■■ ■ ■■

VULCAN XC 605 Pearls 2 4 2 4 4 ■■■ ■■■ ■■■ ■■ ■■■

VULCAN XC 72 Pearls 4 2 5 1 5 ■■ ■■ ■■ ■ ■

VULCAN XC 72 R Powder 4 2 5 1 5 ■■ ■■ ■■ ■ ■■

VULCAN P Pearls 4 1 4 3 2 ■ ■ ■■ ■ ■

VULCAN PF Powder 4 1 4 3 2 ■■ ■■ ■■ ■ ■

VULCAN XC max Pearls 4 2 5 3 5 ■■ ■■■ ■■■ ■■ ■■

1 bad/weak ■■■ highly recommendable ■ on consultation5 very good/strong ■■ recommendable * volatile matter: >3,5 Vol.%Evaluation only within the groups mentioned.BLACK PEARLS®, ELFTEX®, MOGUL®, MONARCH®, VULCAN®, REGAL® and EMPEROR® are registered trademarks of the Cabot Corporation.Market(s) served: CZECH REPUBLIC/SLOVAKIA, GERMANY, POLAND, ROMANIA


| 46 | COLOR

C SinloihiDaylight Fluorescent Pigments

Series Range Forms of delivery Particle size [µm] Main uses and principal characteristics

FZ 5000/6000 Various Colours Powder 3,5–4,5 Standard powder pigment, softening point 130–140 °C, suitable for various applications such as solventbased and waterbased paints and lacquers, silk screen ink and paper coating

FA 40 Various Colours Powder 3,5–4,5 Powder pigment with good stability against various solvents (such as esters and ketones), suitable for applica-tions such as paints and lacquers, gravure inks and screen inks

F 10 Various Colours Powder 3–4 Powder pigment with best lightfastness (addition of UV-Absorber)

FR 50 Various Colours Powder 3,5–4 Powder pigment for plasticized PVC, where resistance to heat and no color migration are required

FX 300 Various Colours Powder 2–4 Powder pigment providing excellent heat stability and and good solvent resistance, temperaturestable up to 260 °C, suiatble for plastics/masterbatch

SX 100 Various Colours Powder 3–5 Formaldehyde free, softening point > 200 °C, suitable for solventbased and waterbased paints and lacquers, printing inks and paper coatings

FM 10 Various Colours Soluble toner Max. 3 mm Soluble toner for solventbased flexo printing inks and ink as well as coating inks for polyester film

BO 100 Various Colours Pigment concen-trated ink base

– for offset and letterpress ink, having highly concentrated very fine particles, Color strength and printability sufficient to one printing-process

SW 100 Various Colours Dispersion < 1 Formaldehyde free pigment dispersion, having very fine particles, in water, good lightfastness, heat stability, chemical resistance and washability in textile uses, suitable for textile printing

SF 3000N Various Colours Dispersion < 0,2 Formaldehyde free pigment dispersion, having very fine particles, suitable for water base marker ink, water base stamping ink etc.

SF 5000 Various Colours Dispersion < 0,1 Formaldehyde free pigment dispersion, having very fine particles, suitable for water base flexographic and gravure ink as well as for (textmarker-)inks

SF 8000 Various Colours Dispersion < 0,4 Formaldehyde free pigment dispersion with high viscosity, having very fine particles, suitable for water base ball points pen ink, gel ink, other waterbased inks

MLCB Green, red, blue Dispersion < 0,1 Formaldehyde free pigment dispersion free, having very fine particles, suitable for aqueous systems in indoor-application. Under normal light these dispersions are invisible, only visible under ultraviolet light in Colors, green, red or blue


COLOR | 47 |

ABC OF RAW MATERIALS CHEMICAL RAW MATERIALS

Worlée Partners

Additives

Binders

Color




| 48 | NOTES

2

1

3

4

4

5

D

ACH

Sales Offices DACH

Sales Offices DACH

1 VB-Hamburg (D) Worlée-Chemie GmbH, VB-Hamburg, 22113 Hamburg [email protected] Tel.: +49 40 733 33 26 50

2 VB-West (D) Worlée-Chemie GmbH, VB-West, 40885 Ratingen [email protected] Tel.: +49 2102 597 98 0

3 VB-Süd-West (D) F.W. Sengewald GmbH, 68770 Ketsch [email protected] Tel.: +49 6202 659 92

4 VB-Süd-Ost (D/A) Worlée-Chemie GmbH, VB-Süd-Ost, 63897 Miltenberg [email protected] Tel.: +49 9371 94 81 90

5 Varistor AG (CH) Varistor AG, Bereich Chemie, CH-5432 Neuenhof [email protected] Tel.: +41 562 66 50 75

SALES ORGANISATION | 49 |


Sales Organisation

Germany

Hamburg Worlée Chemie GmbH, Headquarters, Traded Products Division, Central and East Europe Administration

[email protected] +49 40 733 33 25 00

Lauenburg Worlée Chemie GmbH, Resin Plant / Sales [email protected] +49 4153 59 60

Lübeck Worlée Chemie GmbH, Polymer Plant [email protected] +49 451 61 97 40

Regional German Sales Offices

Sales Area North-East

Worlée Chemie GmbH Sales Office North East [email protected] +49 40 733 33 26 50

Sales Area West

Worlée Chemie GmbH Sales Office West [email protected] +49 2102 597 98 0

Sales Area South-West

F. W. Sengewald GmbH [email protected] +49 6202 659 92

Sales Area South-East

Worlée Chemie GmbH Sales Office South East [email protected] +49 9371 94 81 90

Europe

Austria Worlée Chemie GmbH, VB Süd Ost [email protected] +49 9371 94 81 90

Belgium E.H. Worlée & Co. B. V. [email protected] +31 356 56 14 24

Bulgaria Petrex-E. Ltd. [email protected] +359 28 58 47 77

Croatia/Slovenia/Serbia

Kemoteks d.o.o. [email protected] -com.hr +385 1383 00 67

Czech Republic/Slovakia

Ing. Petr Torma [email protected] +420 377 93 66 01

Finland Brenntag Nordic OY main@brenntag nordic.com +358 954 956 40

France Worlée Chemie GmbH [email protected] +33 2 99 55 81 78

Great Britain E.H. Worlée & Co. (UK) Ltd. [email protected] +44 17 82 71 46 14

Greece Worlée Chemie GmbH c/o Papadimitracopoulos Brothers

pan [email protected] +30 6944 14 98 02

Hungary BESTCHEM Hungária Kft [email protected] +36 1 7 86 47 01

Ireland E.H. Worlée & Co. (UK) Ltd. [email protected] +44 17 8271 46 15

Italy Worlée Italia S.R.L. [email protected] +39 0228 04 03 79

Luxemburg E.H. Worlée & Co. B. V. [email protected] +31 356 56 14 24

The Netherlands E.H. Worlée & Co. B. V. [email protected] +31 356 56 14 24

Macedonia Intelcom Doo [email protected] +389 2 2655 550 / 556

Norway Harald Mathisen A/S [email protected] +47 2240 59 40

Poland Worlée Polska Sp.z.o.o [email protected]@worlee.de

+48 32401 14 60


| 50 | SALES ORGANISATION

Europe

Portugal Mapril S.A. [email protected] +351 22030 43 00

Romania M.R. Chimtrade S.R.L. [email protected] +40 31711 03 92

Spain Montse Solà [email protected] +34 93 778 11 86

Sweden Brenntag Nordic AB niklas.ekman@brenntag nordic.com +46 4028 73 23

Switzerland Varistor AG Chemical Division [email protected] +41 56266 50 75

Turkey Kar Kimya San.ve Tec. Ltd. Sti. [email protected] +90 216317 65 30

Russia/GUS

Stoelck Aussenhandel AG [email protected] +7 495 258 24 75 / 76

Interchemmet Company Limited msm@int chemmet.spb.ru +49 4153 59 60

Africa

Egypt African Chemicals S.A.E. [email protected] +20 2 23 78 43 01

+20 2 27 50 86 41

+20 2 27 50 87 40

Morocco Werner Mertz [email protected] +212 22 79 79 29

South Africa Lionheart (PTY) LTD. [email protected] +27 11917 96-61 / 62 / 63

America

Brazil Adexim S/C tecnica@adexim comexim.com.br +55 1139 66 31 55

Canada Ferguson Chemical Innovation [email protected] +905 453 71 31

Mexico Moca y compañia S.A. de C.V. [email protected] +1 155 55 33 01 03

USA Southeastern Region

Deeks & Company Inc. [email protected] +1 770 938 31 00

USA Mid- and Wes-tern Region, British Columbia

Tri-iso TryLine LLC South West

Tri-iso TryLine LLC Mid West

Tri-iso TryLine LLC Pacific Coast and British Columbia

[email protected]

[email protected]

[email protected]

+ 1 909 626 4855

+ 1 630 639 3300

+ 1 425 450 8822

USA North East States

Van Horn, Metz & Co., Inc. [email protected] +1 610 828 45 00

SALES ORGANISATION | 51 |


Australia

Endeavour C&P [email protected] +61 73315 64 96

New Zealand

Rebain International (NZ) Ltd. [email protected] +64 9966 24 45

Asia

Regional Office Asia Pacific

Worlée Chemie GmbH Regional Office Asia Pacific [email protected] +6 03 7118 2001

China Worlée (Shanghai) Trading Co., Ltd. [email protected] +86 21 6247 25 46

Worlée-Chemie GmbH Shanghai Technical Center

India Worlée-Chemie India Private Limited [email protected] +91 22 6 121 49 43/44/45

Victor Agencies [email protected] +91 112 923 29 07

Indonesia OCTA MING GLOBAL, PT [email protected] +62 215 422 10 02

United Chemicals [email protected] +62 21380 38 05

Iran Chemie Yaran Co. Ltd. [email protected] +98 212 205 99 09

Israel Shiran Representatives 2008 Ltd. [email protected] +972 974 304 11

Japan Worlée-Chemie GmbH Yasuhiro Watanabe [email protected] Mobile +81 80 5413 3051

Jordan Target Chemicals Est. [email protected] +962 655 307 71

Korea Rexchem Corporation [email protected] +82 245 462 10

Lebanon Meditrade [email protected] +961 189 47 22/25

Malaysia Entire Concept Sdn Bhd [email protected] +6 03 5122 1335

Philippines Chase Chemical Trading [email protected] +63 2 813 03 01

Kingdom of Saudi Arabia

Chemtec [email protected] +966 2 2843432/284 34 33

Singapore Segachemie Pte. Ltd. [email protected] +65 68 44 13 69

Sri Lanka Tradekem (Pvt.) Ltd. [email protected] +94 112 578 06 01/112 54 90 45

Taiwan/R.O.C. Best Sincerity Co., Ltd. [email protected] +886 227 65 98 89

Neoway Chemicals Co. Ltd. [email protected] +886 7 616 77 19

Thailand Alphani International Co. Ltd. [email protected] +662 216 5665

Vietnam An Thanh Pte [email protected] +84 8383 496 36

UAE Applied Technology +971 648 196 79

Worlée-Chemie GmbH

Grusonstraße 22D-22113 HamburgPhone: +49 40-7 33 33-2500Fax: +49 40-7 33 [email protected]

Kunstharzfabrik/Verkauf Söllerstraße 16 D-21481 Lauenburg/Elbe Phone: +49(0)4153-5 96-0 Fax: +49(0)4153-5 36 49 [email protected] www.worlee.de 04

/201

5

CHEMICAL RAW MATERIALSNATURAL RAW MATERIALS COSMETIC RAW MATERIALS

abc of raw materials - pci magazine | solutions for ... · abc of raw materials | 2 | introduction...

Documents