5100 series a better sliding door - theut glass earley/submittal packages 00/1.1... · 5100 series...
TRANSCRIPT
5100 SeriesA Better Sliding Door
é
Automatic door technology as you’ve never seen it before!
2
5100 Series Sliding Doorsrecord-usa’s new 5100 series sliding door offers the very latest in automatic door technology to assure thequietest, smoothest performance in a sleek and elegant design. Offering a variable breadth of configurationsand functions, the 5100 series assures the architect and building owner a wide array of capabilities inensuring the most safe, secure and attractive entranceway available by choosing from the following options:
Telescopic Doors� Door panels open and close in an elegant and noiseless movement and at different, harmoniously
coordinated speeds. This interesting motion is not only aesthetically pleasing but also functional.The telescopic sliding door operator is ideal for narrow passages where the opening width obtainedwith a standard sliding door would not be sufficient. Crowded entrances are no problem as it opensquickly and quietly.
.
record-usa 5100 Series Automatic Sliding Doors
The 5100 series telescopic doorsutilize 1 ¾” X 6 1/2” framing andare available in 3 or 6 panelconfigurations.
3
5100
Serie
s
Surface Applied Units� The 5100 series automatic sliding door packag
may also be specified or ordered for surfacemounted applications. This allows for the slidingdoor system to be mounted to existing structureswith little or no modification required. The 5100series surface mounted packed is perfect for retrofitconstruction and in providing for ADA compliance..
Automatic Sliding Doors record-usa 5100 Series
All Glass� All Glass- Showcasing a building, emphasizing
a lobby or creating an illusion of openness, the5200 series all glass sliding door system allows thebeauty and elegance to show through the entrancearea with clear line of sight unhindered by verticalstiles. This entrance creates an unobstructed view ofeither the interior or exterior of a building while pro-viding the same smooth, quiet and reliable operationas the 5100 series.
Suitable for high end design applications as well asevery day use, the 5200 series is the perfect compli-ment for architectural design creativity in entrances.
Safety� Meeting the minimum requirements of the ANSI
standards should be the least that you expect foryour door supplier. The 5100 series by record-usacomes standard with the required sensors asmandated by ANSI. In addition, dual safety beamslocated at 24” and 48” above the finished floor areincluded at no charge for the ultimate in protectionto the user of the door.
In addition, flush mounted exit devices are optionalfor securing the breakout function of the door with-out sacrificing exit compliance
4
5100
Serie
s
Automatic Sliding Doors record-usa 5100 Series
4324 Phil Hargett Court Monroe, NC 28110 800 438-1937 704 289-2024 Fax www.record-usa.com
Special Design� Automatic entranceways should add to the
appearance of a building, not detract from it.Through the use of French windows, multiplemuntins, specially aligned verticals or horizontalmembers in doors or transoms, extra sidelites, tallor short bottom rails or a breadth of other varyingoptions the record 5100 series can easily bedesigned to match most any storefront
Tandem� The Tandem sliding door system by record-usa allows
both an identified entry door and an exit door workindependent of each other while sharing the sameheader assembly for aesthetics and design simplicity.Another added feature is that these doors provide alarger clear door opening than the standard 5100series would allow.
Active Infrared Door Sensor
Safety Large pattern Flexible Convenience immunity
Easy adjustment TECHNOLOGY
MOTIONReliable
With its large motion and presence detectionpattern, the i sensor features a safety zone inthe threshold and sidelights that is always on.The size and shape of the detection patterncan be easily adjusted to match almost anyapplication.
Presence detectionDESIGN
i sensor
The extra-wide pattern covers the door openingplus sidelights, providing fast detection for trafficapproaching from any angle. The sensor’s enhancedpattern depth enables it to detect people andobjects farther away and allows the door to openconveniently for them.
By using easily-set switches and shutters, the sensorcan be quickly adjusted for many different appli-cations. No external set-up device is needed.
Snow mode, rain mode and sensitivity adjustmentsmake this sensor suitable for every applicationand even extreme weather conditions.
Model i-oneMounting Height max. 9’10” (3.0m)Detection Area Adjustments Approach Depth Angle ± 15º
Motion Presence Area ± 5ºApproach Width: All spots can beeliminated by dipswitchMotion Presence Area width can beadjusted by shutter
Detection Technique Active Infrared Reflection (PresenceDetection Type)
Power Supply 12 - 24V AC, 12 - 30V DCCurrent Draw 180mA max. (AC 12V)Power/Operating Indicator Green: Standby
Blinking Red: 1 st Row Detection ActiveRed: 2 nd Row Detection ActiveOrange: Motion Detection ActiveBlinking Orange: ApproachDetection Active
Output Contact Form C Relay 50V, 0.3A
(Resistance Load) .
Safety is assured by the two rows of presencedetection closest to the door, which never shut off.The sensor detects a person or object and holds thedoor open as long as they are in the threshold area,even if they stop or pause.
Safety
L arge detection area E asy adjustment
All conditions
Specifications
C
B
A
EFGH
D
IJ
Presence Detection Area
Motion Detection Area
Approach Detection Area
Chart shows figures if all angles are set at 0̊
Detection area chart
Active InfraredDoorSensor
Mounting Height A 7’3’’ (2.20m) 8’2’’ (2.50m) 9’10’’ (3.00m)Distance to mounting surface B 3’9’’ (0.10m) 4’5’’ (0.11m) 5’3’’ (0.14m)Area Depth C presence detection 10’’ (0.25m) 11’ (0.28m) 1’1’’ (0.34m)Area Depth D presence detection 2’ (0.60m) 2’3’’ (0.68m) 2’8’’ (0.82m)Area Depth E motion detection 3’3’’ (1.00m) 3’9’’ (1.13m) 4’6’’ (1.36m)Area Depth F motion detection 4’9’’ (1.45m) 5’5’’ (1.65m) 6’6’’ (1.98m)Area Depth G motion detection 4’11” (1.50m) 5’7’’ (1.71m) 6’9’’ (2.05m)Area Depth H approach detection 8’6’’ (2.60m) 9’9’’ (2.96m) 11’8’’ (3.55m)Area Width I approach detection 14’9’’ (4.50m) 16’9’’ (5.11m) 20’2’’ (6.14m)Area Width J 16’1’’ (4.90m) 18’3’’ (5.57m) 21’11’’ (6.68m)
The i sensor is perfectly suited for almost any type of door or configuration. It can be set for unidirectional detection, which saves energy byallowing the door to close more quickly fordeparting traffic.
F lexible
DE-15̊
0̊
+15̊
CBA
i se
nsor
Relay Hold Time 0.5 to 2sResponse Time < 0.3sOperating Temperature -4ºF - +131ºF (-20ºC - +55º)Dimensions 304 x 70 x 66mm (w x h x d)
)g004( .zo41thgieWAccessories 3m Connection Cable, 2 Mounting
Screws, Mounting Template, Areaadjustment tool
EXPLODED VIEWS & PARTSPARTS LIST
EVPL-07Effective September 1, 2007
record-USA4324 PHIL HARGETT COURT (28110) • POST OFFICE BOX 3099 • MONROE, NC 28111-3099 USA
704-289-9212 • 800-438-1937 WATS • 704-289-2024 FAX
EXPLODED VIEWS AND PARTS PRICE LIST 8-07
INDEX
5100 SLIDER HEADER EXPLODED VIEW~~~~~~~~~~~~~~~~~~~~ 1
5100 SLIDER HEADER ASSEMBLY PARTS~~~~~~~~~~~~~~~~~~~2 5100 SLIDING DOOR EXPLODED VIEW~~~~~~~~~~~~~~~~~~~~~~3 5100 SLIDING DOOR PARTS LIST~~~~~~~~~~~~~~~~~~~~~~~~~~ 4 5100 "SO" PANEL EXPLODED VIEW~~~~~~~~~~~~~~~~~~~~~~~~ 5 5100 "SO" PANEL PARTS LIST~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 6 5100 "O" PANEL EXPLODED VIEW~~~~~~~~~~~~~~~~~~~~~~~~~ 7 5100 "O" PANEL PARTS LIST~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 8 5100 BOTTOM GUIDE ASSEMBLIES~~~~~~~~~~~~~~~~~~~~~~~~ 9 5100 BOTTOM GUIDE PART LIST~~~~~~~~~~~~~~~~~~~~~~~~~~ 10 5200 BOTTOM GUIDE / THRESHOLD~~~~~~~~~~~~~~~~~~~~~~~11,12 5100 ELECTRIC LOCK KITS~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~13 5100 TELESCOPE ELECTRIC LOCK KITS~~~~~~~~~~~~~~~~~~~~14 TRACKLESS ICU VIEW~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~15 TRACKLESS ICU PARTS LIST~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 16
8100/6100 OPERATOR EXPLODED VIEW~~~~~~~~~~~~~~~~~~~~~17 8100/6100 OPERATOR PARTS LIST~~~~~~~~~~~~~~~~~~~~~~~~~ 18 8100/6100 ARM ASSEMBLIES~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~19 SWITCHES & ACCESSORIES~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 20 SWITCHES & ACCESSORIES~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 21
SER
IES
5100
SLID
ER O
PER
ATO
R
6
5
7a
24
3
1
7d
7c7b
10c
10b
9
7g8a
7f7e
12
13b
1314
11
11
10
12
16
14
17
1615
15
18b
18a
25
23c
13a
13
20a
20
19
23b
23
23a
21
10c
10b
5
22
10a
4
1
26 292827
20b
10a
24
4
57
8
13a
13b
30 31
8-07
32
PAGE 1
SERIES 5100 HEADER ASSEMBLY PARTS 8-07
ITEM PART NUMBER DESCRIPTION QTY. REQ'D LIST PRICE1 5-51-4002 COVER, CL-DB *2 5-51-4002 COVER, CENTER 15"(bipart) CL-DB 13 81-0016-2554 SCREW,10-32X1/4" ALLEN CS BL OXIDE (cntr.cvr.) 44 4-51-1037 NUT PLATE, 10-32 (3 holes) 20 typ.5 81-0016-2562 SCREW,10-32X1/2" ALLEN CS BL OXIDE 12 typ.6 4-51-1055 BRACKET, HEADER MOUNTING - LH 17 4-51-0100 DRIVE MODULE, SERIES 5100 17a 4-51-1059 THREADED STANDOFF, M5X14 37b 4-51-1057 PLATE, MOTORDRIVE SPACER 17c 4-51-0101 CHASSIS ASSY.,DRIVE MODULE 17d 9-99-1815 SCREW,M5X20 ALLEN CS Zinc(Motor/GB. Mounting) 37e 9-99-2154 MOTORDRIVE ASSY. 17f 9-99-1322 CONTROL ASSY. 17g 9-99-6597 J1 - CANbus, 25-28 1
9-99-6600 J2 - Ext.&Aux. Sensors, B/O,C/O, 1-12 19-99-6598 J3 - Rem. Sensor, Rkr./Key Panel, 13-18 19-99-6596 J4 - Interior Sensor, 21-23 19-99-6599 J5 - Safety Beams, 30-37 1
8 9-99-6813 TRANSFORMER, 115 Volt Primary 18a 9-79-0008 FILTER, Powerline, FUSE,5x20, 2 1/2amp,slow blow 19 4-51-4010 COVER, Power Supply 110 4-51-0007 BRACKET ASSY., UP. SIDELITE PVT. - LH 110a 4-51-1047 BRACKET, UPPER SIDELITE PIVOT 110b 9-58-0008 PIN, CLEVIS, 3/8"x1 1/4" 110c 9-99-0232 BEARING, FLANGED 111 4-51-1001 BRACKET, BELT BASE 212 4-51-1002 BRACKET, BELT CLASP 213 4-51-0009 BRACKET ASSY., SIDELITE STRIKE 213a 4-51-1010 BRACKET, SIDELITE STRIKE 213b 9-73-0080 PANIC SWITCH, MAGNETIC N/O 214 4-51-1045 BRACKET, LOCK STRIKE (standard) 215 9-99-3503 NUT, M6 X 0.5 216 9-51-0006 BOLT, HAMMER HEAD, (electric lock) 217 4-51-0003 CARRIER ASSY., LOWER BELT 118a 4-51-0103 LOCK, ELECTRIC (Fail Safe) Kits see page 13,14 118b 4-51-0104 LOCK, ELECTRIC (Fail Secure) Kits see page 13,14 119 4-51-0004 CARRIER ASSY., UPPER BELT 120 4-51-0006 IDLER PULLEY ASSY. 120a 9-51-0004 PULLEY, IDLER 120b 4-51-1009 BRACKET, IDLER PULLEY 121 4-51-0010 PLATE ASSY., TERMINAL BLOCK 122 4-51-1004 BRACKET, CONDUIT ANCHOR 123 4-51-0012 CARRIER ASSY., SLAVE 223a 4-51-0005 ROLLER ASSY., CARRIER 223b 4-51-0021 ROLLER ASSY., ANTI-RISE 123c 9-99-1813 SCREW, M6X16, HEX, SER.FLANGED HD. 124 4-51-0020 ASSY.,DOOR STOP 225 4-51-0008 BRACKET ASSY.,UP. SIDELITE PVT. - RH 126 5-51-4001 HEADER, SERIES 5100 SLIDER CL-DB 127 5-51-4004 ROLLER TRACK, SERIES 5100 SLIDER 128 9-51-0001 DAMPER, ROLLER TRACK 129 4-51-1056 BRACKET, HEADER MOUNTING - RH 130 9-99-3507 NUT PLATE, SQUARE, 1/4-20 (1Hole) 17 typ.31 81-0017-2658 SCREW, 1/4-20X3/8"Allen BH Flanged 17 typ.32 9-09-0012 BELT, TIMING, 5100 1
NOTE: For Safety Beam Info, refer to page 21, Switches & Acessories
PAGE 2
SERIES 5100 SLIDING DOOR"SX" PANEL
8-07
1 2 3
54
6
7
9
10
13
8
12
11
1716
1514
212019
18
22
23
24
27
29
28
25
26
30
35
37
38
33 34
31 32
39
36
44
43
42 41
40
46
45
PAGE 3
SERIES 5100 SLIDING DOOR"SX" PANEL
8-07
ITEMPART
NUMBER DESCRIPTIONQTY.
REQ'D.LIST
PRICE ITEMPART
NUMBER DESCRIPTIONQTY.
REQ'D.LIST
PRICE1 4-51-1049 END CAP, DOOR CATCH 2 26 4-11-4095 INTERLOCK, CL-DB 22 81-0011-2670 SCREW, 1/4-20 X 1" FHSH 3 27 9-99-2596 BLOCK, GLASS JACKING 13 81-0718-3666 BOLT,1/4-20X3/4"HHS GRADE 5
W/NYLON PATCH2 28 81-4411-0516 SCREW 10-24X3/4" PFH, TYPE "F" 8
4 5-51-4006 DOOR CATCH CL - DB 1 29 81-0017-3664 BOLT,1/4-20X5/8" HWH GR.8 45 81-0011-2658 SCREW,1/4-20x3/8" FHSH 2 30 4-51-9004 COVER,DOOR CATCH, plastic 1
6 9-99-2594 SEAL, FOAM RUBBER, 2" LENGTH 1 31 5-11-4022 STILE, FIXED, CL-DB 1.7 9-99-7318 WEATHERPILE, MOHAIR, BLACK 2 32 5-11-4021 STILE, TANDEM CL-DB 18 4-51-1038 HOUSING, DOOR CATCH ASSY. 1 33 4-11-4096 SHEAR BLOCK "SB1" 29 4-51-1039 INTERLOCK,LH, DOOR CATCH
(RH 4-51-1040)1 34 81-3514-0664 SCREW #14 X 5/8" PPH TYPE "B" 2
10 9-99-7316 WEATHERPILE, MOHAIR, BLACK 2 35 81-4411-0512 SCREW 10-24X1/2" PFH, TYPE "F" 411 4-51-0001 WELDMENT, TORQUE BAR 1 36 5-11-4031 MUNTIN, CL-DB 112 4-51-1003 BRACKET,
TORQUE TUBE SUPPORT1 37 9-99-0064 KEY CYLINDER, CL-DB (pair) 1
13 9-99-7358 WEATHERPILE, CHANNEL, BLACK 1 38 9-99-0069 CYLINDER, THUMBTURN, CL-DB 114 6-11-9003 CHANNEL, WEATHERPILE 1 39 9-99-0071 DEADLOCK, HOOKBOLT 115 4-70-4104 PIVOT,TORQUE TUBE BOTTOM
W/5/16X1" FH SCREW1 40 81-4411-0516 SCREW,10-24X3/4" PFH TYPE"F" 8
16 4-11-1082 BACKER PLATE, "BP1", TOP 2 41 5-11-4033 3 1/2" BOTTOM RAIL CL-DB 1 17 4-11-4097 SHEAR BLOCK -"SB2", TOP 2 42 81-0074-0558 SCREW,10-32X3/8"PPH,CL 418 5-51-4009 RAIL, TOP, 3", CL - DB 1 42a 81-0014-0558 SCREW,10-32X3/8"PPH,SS BL 419 81-0014-0680 SCREW,GLASS ADJUST
1/4-20X2" PPH 1 43 4-11-0469 PIN GUIDE ASSY. RH&LH 1
20 4-70-0582 ROLLER CATCH 1 44 4-11-1082 BACKER PLATE "BP1" BOTTOM 221 4-51-1042 PLATE, INTERLOCK ASSY. 1 45 4-11-4097 SHEAR BLOCK "SB2" BOTTOM 222 4-51-1041 BRACKET, INTERLOCK ASSY. 1 46 81-0017-3664 BOLT 1/4-20X5/8" HWH GR.8 423 9-99-7316 WEATHERPILE, MOHAIR, BLACK 2 47 9-99-7355 SWEEPSTRIP W/BRUSH(not shown) 124 81-0016-2658 SCREW,1/4-20X3/8"BSCS-SS 225 81-0014-2670 SCREW, 1/4-20 X 1" BSCS-SS 2 ~ 5-11-4040 SASH, 1/4" SQUARE CL-DB ~
~ 5-11-4039 GUTTER, 1/4" SQUARE CL-DB ~~ 5-11-4042 SASH, 1" SQUARE CL-DB ~~ 5-11-4041 GUTTER, 1" SQUARE CL-DB ~~ 6-11-9011 VINYL, GLAZING BULB ~
PAGE 4
SERIES 5100 SWING OUT SIDELITE"SO" PANEL
8-07
5100 RH SIDELITE"SO" PANEL
12
3
4
5
67
8
10
1112
13
14
15
16
17
18
19
202122
23
24
25
26
27
9
2829
PAGE 5
SERIES 5100 SWING OUT SIDELITE "SO" PANEL
8-07
ITEM PART NUMBER DESCRIPTION QTY. REQ'D LIST PRICE1 5-11-4021 STILE, TANDEM CL-DB 12 4-11-4098 SHEAR BLOCK, "SB3", TOP 23 5-11-4034 RAIL, UPPER CL-DB 1
4 81-0014-06801/4-20 X 2" PPH
GLASS ADJ. SCREW 15 4-11-4093 BRACKET, PANIC SWITCH MAGNET 1
6 4-70-0672ROLLER CATCH ASSY.(TOP & BOTTOM) INCLUDES 4-70-0582 BALL DETENT 2
7 5-11-4022 STILE, FIXED CL-DB (NARROW) 1
8 4-11-1086PIVOT ANGLE "PA1-R" (SILVER-TOP)
with 9-99-0232 BEARING 1
9 81-0017-3666BOLT,1/4-20 X 3/4" HWH GR.8
(TOP & BOTTOM) 410 81-4411-0512 SCREW,10-24 x 1/2" PFH 811 9-99-2596 BLOCK, GLASS JACKING 1
12 81-0017-3664BOLT,1/4-20 X 5/8" HWH GR.8
(TOP & BOTTOM) 413 4-11-1082 BACKER PLATE "BP1" 114 81-3514-0512 SCREW,10-24 X 3/4" PFH Type F 415 4-11-4095 INTERLOCK CL-DB (TYP.) 216 9-99-7316 WEATHERPILE CL-DB ~17 5-11-4031 MUNTIN BAR (1 1/2") CL-DB 118 4-11-4096 SHEAR BLOCK "SB1" 219 81-4411-0512 SCREW,10-24 X 3/4" PFH Type F 820 81-3514-0664 SCREW,#14 X 5/8" PPH TYPE "B" 221 6-11-9003 CHANNEL, WEATHERPILE 122 9-99-7316 WEATHERPILE CL-DB ~
23 4-11-1085PIVOT ANGLE "PA2-R" (GOLD-BOTTOM)
with 9-99-0232 BEARING 124 5-11-4033 RAIL, BOTTOM (3 1/2") CL-DB 125 81-4411-0516 SCREW,10-24 X 3/4" PFH Type F 826 4-11-4097 SHEAR BLOCK "SB2" 227 4-11-1082 BACKER PLATE "BP1" 228 4-11-1031 PIN, SIDELITE PIVOT, BOTTOM 129 4-51-4008 BLOCK, SIDELITE PIVOT, BOTTOM 1
~ 5-11-4040 SASH 1/4" SQUARE CL-DB ~~ 5-11-4039 GUTTER 1/4" SQUARE CL-DB ~~ 5-11-4042 SASH, 1" SQUARE CL-DB ~~ 5-11-4041 GUTTER 1" SQUARE CL-DB ~~ 6-11-9011 VINYL, GLAZING BULB ~
NOTE: For Safety Beam Info, refer to Page 21, Switches & Accessories
PAGE 6
SERIES 5100 FIXED SIDELITE"O" PANEL
8-07
5100 LH FIXED SIDELITE"O" PANEL
15
5
4
3
21
11
12
13
9
6
8
7
1016
14a
14b
PAGE 7
SERIES 5100 FIXED SIDELITE"O" PANEL
8-07
ITEM PART NUMBER DESCRIPTION QTY. REQ'D LIST PRICE1 5-11-4022 STILE, FIXED CL - DB (narrow) 22 4-11-4098 SHEAR BLOCK "SB3" TOP 2
3 5-11-4034 UPPER RAIL CL -DB 1
4 4-11-1082 BACKER PLATE "BP1" 25 81-4411-0512 SCREW, 10-24-1/2" PFH Type F 4
6 81-3514-0664 SCREW, #14 X 5/8" PPH Type B 2
7 5-11-4031 MUNTIN CL - DB 1
8 4-11-4096 SHEAR BLOCK "SB1" 29 81-4411-0512 SCREW, 10-24X1/2"PFH Type F 810 6-11-9005 VINYL, SIDELITE SEAL 1
11 81-0017-3664 BOLT, 1/4-20X5/8" HWH 812 5-11-4032 2 1/2" BOTTOM RAIL CL-DB 1
13 4-11-4096 SHEAR BLOCK "SB1" 2
14a 6-11-9003 CHANNEL, WEATHERPILE 1
14b 9-99-7316 WEATHERPILE 115 81-4411-0516 SCREW, 10-24X3/4 " PFH Type F 8
16 4-11-1082 BACKER PLATE "BP1" 2
~ 5-11-4040 SASH, 1/4" SQUARE CL-DB ~~ 5-11-4039 GUTTER, 1/4"SQUARE CL-DB ~~ 5-11-4042 SASH, 1" SQUARE CL-DB ~~ 5-11-4041 GUTTER, 1" SQUARE CL-DB ~~ 6-11-9011 VINYL, GLAZING BULB ~
NOTE: For Safety Beam Info, refer to Page 21 , Switches & Accessories
PAGE 8
SERIES 5100 BOTTOM GUIDE SYSTEMS
8-07
4-11-7001 - PIN
9-99-4575 -RETAINER RING
81-6019-2666 - SET SCREW
4-11-1062PLATE (BLANK)
FIXED PANEL BOTTOM GUIDE USED FROM 1-1-03 WILL RETROFIT TO OLD STYLEDOOR EXTRUSION AND WORK WITH CURRENT GUIDE RAIL EXTRUSION.
9-65-0006 -RETAINER RING
4-70-0702 - ROLLERand BEARINGASSY.
4-11-1078 - STUD
4-11-1063 - BOTTOMGUIDE PLATE - LH
4-11-1064 - BOTTOMGUIDE PLATE - RH(SHOWN)
4-11-1081-BRACKET
4-11-7002 -PIN
9-99-4575 -RETAINER RING
81-6019-2666 -SET SCREW
9-99-5702 -SPRING, FINGER
9-99-4622 -RETAINER RING
FIXED PANELBOTTOM GUIDEASSEMBLY4-11-0470 - LH4-11-0471 - RH (SHOWN)
4-11-1081 -BRACKET
4-11-7002 -PIN
9-99-4575 -RETAINER RING
81-6019-2666 -SET SCREW
9-99-5702 -SPRING, FINGER
9-99-4622 -RETAINER RING
4-12-1035 -PLATE (BLANK)
9-99-3439 - NUT
9-99-7225 - WASHER
4-11-1027 - BOTTOMPIVOT BRACKET
4-70-1069 -PIN
9-65-0006 -RETAINER RING
4-70-0702 - ROLLERand BEARING ASSY.
4-11-1078 - STUD4-19-4062 - LH4-19-4063 - RH
BOTTOM RAILSECONDARY DOOR9-65-0006 -
RETAINER RING
4-70-0702 - ROLLERandBEARING ASSY.
4-11-1078 - STUD
4-11-1018 - BOTTOMGUIDE PLATE - LH (SHOWN)
4-11-1017 - BOTTOMGUIDE PLATE - RH
PIN GUIDE ASSEMBLY4-11-0469 RH & LH
BOTTOM GUIDE RAIL5-11-4018 (PER FOOT)
REVERSE BREAKOUT BOTTOM GUIDE 4-11-0459
TRACKLESS ICUBOTTOM GUIDE4-19-0026 LH (SHOWN)4-19-0027 RH
FIXED PANEL BOTTOM GUIDE ASSEMBLYPRIMARY TO SECONDARY DOOR4-12-0470 LH (SHOWN)4-12-0471 RH
BOTTOM GUIDE CHANNEL5-19-4003 (PER FOOT)
G-RAIL INSERT 5-51-4014
RAMPED PIN GUIDE TRACK5-11-4008
BOTTOM GUIDE TRACK CAP 9-70-0077
NOTE: ALSO USED ON THE 5100 TELESCOPEFIXED PANEL BOTTOM GUIDE SYSTEM
(CALL FACTORY FOR OLDER UNITS)
4-11-1081 - BRACKET
BOTTOM GUIDE FOR FULL BREAK OUT SLIDERUSED ON ALL SLIDERS AS OF 1-1-03
INSERT, PIN GUIDE5-51-4015
RAMPED PIN GUIDE TRACKTELESCOPE 5-51-4013
NOTE: ALSO USED ON THE 5100 TELESCOPEFULL BREAKOUT BOTTOM GUIDE SYSTEM
ITEM #1ITEM #2
ITEM #6&7
ITEM #4
ITEM #5
ITEM #14
ITEM #12&13
ITEM #8&9 ITEM #10
ITEM #11
ITEM #3
ITEM #15
PAGE 9
SERIES 5100 BOTTOM GUIDE SYSTEMS
8-07
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE1 4-11-0469 PIN GUIDE ASSY. RH & LH 12 5-11-4008-MF RAMPED PIN GUIDE TRACK 13 5-51-4015-MF INSERT, PIN GUIDE 14 9-70-0077 BOTTOM GUIDE TRACK CAP 15 4-11-0459 REVERSE BREAKOUT PIN GUIDE ASSY. 16 4-19-0026 TRACKLESS ICU BOTTOM GUIDE ASSY.-LH 17 4-19-0027 TRACKLESS ICU BOTTOM GUIDE ASSY.-RH 18 4-11-0470 FIXED PANEL BOTTOM GUIDE ASSY.-LH 19 4-11-0471 FIXED PANEL BOTTOM GUIDE ASSY.-RH 110 5-11-4018 BOTTOM GUIDE RAIL CL-DB 111 5-51-4014-MF G-RAIL INSERT 1
5100 TELESCOPE BOTTOM GUIDE SYSTEMS12 4-12-0470 FIXED PANEL BOTTOM GUIDE ASSY.- LH
TELESCOPE PRIMARY TO SECONDARY1
13 4-12-0471 FIXED PANEL BOTTOM GUIDE ASSY.- RH TELESCOPE PRIMARY TO SECONDARY
1
14 5-19-4003-MFBOTTOM GUIDE CHANNEL
TELESCOPE SECONDARY DOOR 115 5-51-4013-MF RAMPED PIN GUIDE TRACK - TELESCOPE 1
PARTS1 4-70-0702 ROLLER & BEARING ASSY. 22 4-11-1078 STUD 23 9-65-0006 RETAINER RING 24 4-70-1069 PIN 15 9-99-7225 WASHER 16 9-99-3439 NUT 1
PAGE 10
SERIES 5200 ALL-GLASSBOTTOM GUIDE SYSTEM
8-07
9-65-0006 -RETAINER RING
4-70-0702 - ROLLERandBEARING ASSY.
4-11-1078 - STUD
THRESHOLD
THRESHOLD 1/2" x 4 1/2"5-40-4005
BOTTOM GUIDE RAIL5-11-4018 (PER FOOT)
ALL-GLASS BOTTOM GUIDE ASSY.4-52-0010 LH (SHOWN)4-52-0011 RH
THRESHOLD 1/2" X 7"5-11-4011
THRESHOLD 1/4" X 7"5-11-4017
G-RAIL INSERT 5-51-4014
WEATHER PILELEADING EDGE 9-99-7349
5200 ALL-GLASS WEATHERSTRIP
SEAL, FINNED6-52 9001
ITEM #1
ITEM #1 ITEM #2
ITEM #3&4ITEM #2
ITEM #2
ITEM #3
ITEM #1
PAGE 11
SERIES 5200 ALL-GLASSBOTTOM GUIDE SYSTEM
8-07
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE1 5-51-4014 G-RAIL INSERT 22 5-11-4018 BOTTOM GUIDE RAIL CL-DB 13 4-52-0010 ALL-GLASS BOTTOM GUIDE ASSY.-LH 14 4-52-0011 ALL-GLASS BOTTOM GUIDE ASSY.-RH 1
ALL-GLASS WEATHERSTRIP1 9-99-7349 WEATHERPILE, LEADING EDGE 12 6-52-9001 SEAL, FINNED 1
THRESHOLD1 5-11-4011 THRESHOLD 1/2" X 7" SADDLE - MF 12 5-11-4017 THRESHOLD 1/4" X 7" SADDLE - MF 13 5-40-4005 THRESHOLD 1/2" X 4 1/2" SADDLE - MF 1
PARTS1 4-70-0702 ROLLER & BEARING ASSY. 22 4-11-1078 STUD 23 9-65-0006 RETAINER RING 24 4-70-1069 PIN 15 9-99-7225 WASHER 16 9-99-3439 NUT 1
PAGE 12
SERIES 5100ELECTRIC LOCK ASSEMBLY KITS
8-07
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE1 4-51-0801 KIT, BI-PART, FAIL-SAFE 11a 4-51-0103 LOCK ASSY., ELECTRIC - FAIL SAFE 11b 81-0017-2658 SCREW, 1/4-20X3/8" BFHCS 71c 4-51-1045 BRACKET, LOCK STRIKE (standard) 21d 9-99-3503 NUT, M6X0.5 21e 9-51-0006 BOLT, HAMMERHEAD 21f 9-99-3507 NUT PLATE, 1/4-20 (not shown) 3
2 4-51-0805 KIT, BI-PART, FAIL SECURE 12a 4-51-0104 LOCK ASSY., ELECTRIC(FAIL SECURE) 12b 81-0017-2658 SCREW, 1/4-20X3/8" BFHCS 72c 4-51-1045 BRACKET, LOCK STRIKE (standard) 22d 9-99-3503 NUT, M6X0.5 22e 9-51-0006 BOLT, HAMMERHEAD 22f 9-99-3507 NUT PLATE, 1/4-20 (not shown) 3
1a
1c1d 1b
1e
2b2c
2d2e
2a
PAGE 13
SERIES 5100 TELESCOPEELECTRIC LOCK ASSEMBLY KITS
8-07
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE1 4-51-0803 KIT, 6 PANEL TELE., FAIL SAFE 11a 4-51-0103 LOCK ASSY., ELECTRIC - FAIL SAFE 11b 81-0017-2658 SCREW, 1/4-20X3/8" BFHCS 71c 4-51-1046 BRACKET, LOCK STRIKE (telescope) 21d 9-99-3503 NUT, M6X0.5 21e 9-51-0006 BOLT, HAMMERHEAD 21f 9-99-3507 NUT PLATE, 1/4-20 (not shown) 3
2 4-51-0807 KIT, 6 PANEL TELE., FAIL SECURE 12a 4-51-0104 LOCK ASSY., ELECTRIC(FAIL SECURE) 12b 81-0017-2658 SCREW, 1/4-20X3/8" BFHCS 72c 4-51-1046 BRACKET, LOCK STRIKE (telescope) 22d 9-99-3503 NUT, M6X0.5 22e 9-51-0006 BOLT, HAMMERHEAD 22f 9-99-3507 NUT PLATE, 1/4-20 (not shown) 3
1a
1b1c1d 1e
2c2d
2a
2e2b
PAGE 14
SERIES 5900 TRACKLESS ICUSO-SX (shown)
8-07
5900 TRACKLESS ICULH (SO-SX)
1
2
3
5
4
16
7
6
13
12
11
10
9
8
18
17
15
14
19
2120
22
23
2627
28
2425
PAGE 15
SERIES 5900 TRACKLESS ICUPARTS LIST
8-07
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE1 5-59-4003 COVER, ICU CL-DB 12 5-59-4001 HEADER, ICU CL-DB 13 4-59-1003 BRACKET, HEADER MNTING. - LH 14 4-59-1004 BRACKET, HEADER MNTING. - RH 15 5-60-1418 SIDE JAMB 1 3/4"X4 1/2" CL-DB 26 5-60-1532 JAMB FILLER CL-DB 27 4-51-0012 CARRIER ASSY., SLAVE 28 9-99-2833 DOOR PULL, RECESSED 19 4-79-0100 ICU DOOR WHEEL ASSY. 1
10 5-19-4003 BOTTOM GUIDE CHANNEL - MF 111 4-19-9001 BLOCK, TRANSFER PIVOT 112 4-19-0026 TRACKLESS BOTTOM GUIDE ASSY.-LH 1
~~~ 4-19-0027 TRACKLESS BOTTOM GUIDE ASSY.-RH 113 4-51-0001 WELDMENT, TORQUE BAR 114 9-99-0073 FLUSHBOLT, MANUAL CL-DB 115 4-11-1086 PIVOT ANGLE, TOP "PA1-L" 116 4-19-1020 PIVOT ANGLE, BOTTOM, TRACKLESS
(not shown)1
17 9-99-0232 BEARING, FLANGED 218 4-19-0025 TRANSFER PIVOT ASSY.
uses 4-19-7001 stud1
19 9-58-0008 CLEVIS PIN (not shown) 120 4-60-1091 BRACKET, SIDELITE PIVOT 121 4-11-1031 PIN, SIDELITE PIVOT 122 4-24-9003 SLIDE BLOCK 123 4-20-1090 STUD, SLIDE ARM (not shown) 124 4-19-1016 STOP LINK ARM >40" SLW 125 4-19-1015 STOP LINK ARM <40" SLW 126 4-19-1017 STOP LINK TRACK <40" SLW 127 4-19-1018 STOP LINK TRACK >40" SLW 128 4-19-1019 STOP BLOCK 1~~ 4-59-0019 TUBE ASSY., ANTI-BREAKOUT- CL-DB
includes 4-49-4004 & 4-59-9002 END CAP (not shown)
1
~~ 9-99-2813 DOOR PULL, SURFACE CL-DB ~~~ 9-99-2809 DOOR PULL, SURFACE CL-DB BACK
TO BACK ~
~~ 9-99-2827 DOOR PULL, SURFACE CL-DB OFFSET
~
~~ 9-99-2832 DOOR PULL, SURFACE CL-DB OFFSET, BACK TO BACK
~
PAGE 16
1a
b
54
3
8
76
110
9
11
12
13
14
16a
18
17
1615
11SE
RIE
S 61
00/8
100
SWIN
G D
OO
R O
PER
ATO
R
8-07
2
c
3
d
24
23
a b c d
11
PAGE 17
SERIES 6100/8100 SWING DOOR OPERATOR
8-07
ITEM PART NUMBER DESCRIPTION QTY. REQ'D. LIST PRICE1 4-80-0802 KIT, RKR. SWITCH,CABLE,INSERT,& SCREWS 1a 6-80-9004 INSERT, COVER (SWITCH) 1b 9-99-1323 ROCKER SWITCH ASSY. BDI MODULE 1c 9-99-0463 CABLE, ROCKER SWITCH ASSY. 1d 81-4814-0106 SCREW, 2-28X5/16" Ph. PH PLASTITE, ZINC 22 9-99-3507 NUT PLATE, SQUARE,1/4-20 (1 hole) 12 typ.3 6-80-9001 END CAP, COVER 24 81-3114-0412 SCREW, 8x1/2" Ph. PH SMS BL OXIDE 45 81-0017-2658 SCREW, 1/4-20X3/8" ALLEN BH BL OXIDE 12 typ.6 5-80-4001-MF PLATE, OPERATOR MOUNTING, 6100/8100 17 9-80-0103 MOUNTING SET, HARD STOP ADAPTOR 1
8a 9-80-0100 8100 OPERATOR, COMPLETE DRIVE MODULE, CONTROL, STOP SET, POWER SUPPLY, ROCKER
SWITCH & CABLE
1
8b 9-80-0101 8100 DRIVE MODULE, W/ CONTROL 18c 9-61-0100 6100 OPERATOR, COMPLETE DRIVE MODULE,
CONTROL, STOP SET, POWER SUPPLY, ROCKER SWITCH & CABLE
1
8d 9-61-0101 6100 DRIVE MODULE, W/ CONTROL 19 81-0014-2666 SCREW 1/4-20X3/4" ALLEN BH, BL OXIDE 4
10 9-80-0108 CIRCUIT BOARD, SERIES 6100/8100 OPERATOR 111 6-80-9003 INSERT, PLAIN, COVER & END CAP 2 typ.12 6-80-9002 INSERT, SHAFT CUTOUT, COVER 113 5-80-4004 COVER, 6100/8100 CL-DB 114 4-80-0801 KIT, PLUG-IN TERM. STRIPS & JUMPERS 1
9-99-6606 J1 CONNECTOR, (CANBUS) 25-28 19-99-6601 J2 CONNECTOR, (AKA, AKI) 1-7 19-99-6602 J3 CONNECTOR, (AUX/SIO/SIS) 8-13 19-99-6603 J4 CONNECTOR, (EMERG. C/O) 14-15 19-99-6604 J5 CONNECTOR, (ALARM) 16-18 19-99-6605 J6 CONNECTOR, (VRR/VAK) 19-24 1
15 9-80-0010 HARNESS, ENCODER 116 9-99-1902 FUSE HOLDER 116a 9-99-1940 FUSE, 5x20, 2 1/2 amp, slow blow 117 9-80-0102 POWER SUPPLY, 6100/8100 118 4-51-1004 BRACKET, CONDUIT ANCHOR 119 9-80-0009 HARNESS, PWR. SUPPLY>CONTROL (not shown) 120 9-99-0783 SHORTING BRIDGE (jumper),TERM. BLOCKS 3 typ.21 9-99-0784 SHORTING BLOCK for 0.1C/L POSTS 2 typ.22 4-80-0803 KIT, HEADER ACCESSORY PKG.
endcaps,inserts,screws,nut plates, decal1
23 9-80-0109 MOTORDRIVE ASSY., 8100 124 9-61-0109 MOTORDRIVE ASSY., 6100 1
~~ 4-80-4016 COVER ONLY, MACHINING, SINGLE CL-DB 1~~ 4-80-4018 COVER ONLY, MACHINING, DUAL CL-DB 1~~ 4-80-0013 COVER & BACKPLATE ASSY.,SINGLE CL-DB (complete) 1~~ 4-80-0018 COVER & BACKPLATE ASSY.,DUAL CL-DB (complete) 1
PAGE 18
SERIES 6100/8100ARM ASSEMBLIES
8-07
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE1 9-80-0105-CL STANDARD ARM ASSY. w/20mm Adaptor 1
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE2 9-80-0104-CL SLIDE TRACK ARM ASSY. w/20mm Adaptor 1
1 9-80-0011-CL ARM ADAPTOR 80MM (3") 12 9-80-0007-CL ARM ADAPTOR 50MM (1 3/4") 13 9-80-0006-CL ARM ADAPTOR 20MM (1/2") 14 9-80-0107-CL OFFSET ARM ADAPTOR 15 4-80-0804-CL DOUBLE EGRESS ADAPTOR KIT 1
1 2 3
4 5
PAGE 19
SWITCHES and ACCESSORIES 8-07
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE1 4-51-0105 CONTROL MODULE, DUAL ROCKER 12 4-51-0106 CONTROL MODULE, ROCKER/KEYSWITCH 1
3 9-99-1321CONTROL MODULE, DISPLAY
no cable - no plug 1
3a 4-51-0107CONTROL MODULE, DISPLAY
w/cable - w/plug 14 9-15-0001 ENCLOSURE, CONTROL MODULE 1
5 4-80-0800CONTROL MODULE, DISPLAY
with ENCLOSURE w//cable - no plug
1 9-99-5570 Uninterruptable Power Supply (UPS) 12 9-51-0010 BATTERY PACK, ( NICAD ) 1
1 2 3 3a 4
5
Power /Reset
CircuitBreaker
OU
TPU
TIN
PUT Neutral / White (IN)
Hot / Black (IN)
Ground / Green
Hot / Black (OUT)
Neutral / White (OUT)
Battery Backup & Surge Protector
DANGERHigh Voltage
This unit stores power.Disconnect battery beforeservicing.
200V
A
DANGERHigh Voltage
This unit stores power.Disconnect battery beforeservicing.
2
1
4 1/2"W x 3 1/4"H x 1 3/8"D
20 1/2"W x 3 3/4"H x 2 3/4"D
PAGE 20
SWITCHES and ACCESSORIES 8-07
ITEM PART NUMBER DESCRIPTION QTY. LIST PRICE1 9-99-1317 FPC902 - FLASHPROGRAMMER 12 9-59-0001 AC ADAPTOR BATTERY CHARGER,
FPC9021
1 4-51-0808 SAFETY BEAM SET, 5100 1ea.-9-61-0041 2ea.-9-61-0042
1
2 9-61-0041KIT,SAFETY BEAM WIRE ASSY.,
HEADER 1ea.(C) ; 1ea.(D)1
3 9-61-0042 KIT, BEAM HEAD w/WIRE ASSY.
1-EMITTER - (F) & HARNESS - (E) 1-RECEIVER - (A) & HARNESS - (B)
1
4 9-61-0043 KIT, WIRE ASSY.,BEAM HEADS 2ea.(B) ; 2ea.(E)
1
5 9-61-0045 EMITTER, Black Wire -(F) 16 9-61-0046 RECEIVER, Gray Wire - (A) 1
(A)(B)
(C)
(D)(E)
(F)
PAGE 21
Automatic Sliding Door Comparison Chartrecord Stanley Horton 2000 Besam Uni‐slide
Standard Warranty (complete unit) 2 years 1 year 1 year 1 yearRoller Track Warranty Lifetime 1 year 1 year 1 yearRoller Warranty 3 Year 1 year 1 year 1 yearRollers per panel* 4 2 4 2Operating Temperature Range negative 40 to 140 Fahrenheit negative 30 to 130 Fahrenheit negative 30 to 130 Fahrenheit negative 35 to 122 FahrenheitMaximum Door Panel Weight 300 lbs. 220 lbs. 250 lbs. 220 lbs.Header Size* 4‐1/2" x 7" 6" x 8" 4" x 6" 7‐5/8" x 6‐5/8"Break‐out panel control* Concealed Hydraulic Closer Limit Arm Torsion Spring Hydraulic Dampner (optional)Door Panel Construction* Mortise Block Through‐Bolts Mortise Block Mortise BlockDiagnostics Exposed via LCD Stanley Personnel Only Horton Personnel Only Besam Personnel OnlyLife cycle counter Exposed via LCD Stanley Personnel Only Not Available Besam Personnel OnlySafety Adjustments Software limits to ANSI 156.10 Relies on Service Tech to comply Relies on Service Tech to comply Relies on Service Tech to complyWeather Stripping Extruded Channel in Door Panels Adhesive "stick on" weather stripping Extruded in Door Panels Extruded Channel in Door PanelsStandard Safety Detection 2 infrared curtains, 2 beams 1 infrared curtain, 2 beams 2 infrared curtains, 2 beams 2 infrared curtainsUni‐Directional Motion Detection Standard Standard Standard StandardBottom Guide Design* Round Pin=Anti‐Friction, Smooth, Quiet Fork Guide=Friction & Wear Round Pin Round PinPower Consumption 100 Watts 650 Watts 300 Watts 250 WattsMotor Size**** 1/8 HP 1/4 HP 1/8 HP 1/8 HP
** Header Size : 4‐1/2" wide header sits flush with standard storefront framing** Door Panel Construction : Mortise blocks lock the stile and rail in place adding structural integrity*
**** Motor Size
Break‐out Panel Control : Hydraulic closer controls door panel in break‐out mode, limit arm creates rigid stopping point causing damage
Please note the discrepancy in motor size, this is critical to explaining the difference between the two manufacturers. The Record 5100utilizes an 1/8 HP motor compared to the Stanley which uses 1/4 HP motor. Efficient output of a drive train is achieved by gear reduction.Efficient gear reduction increases the amount of RPM, thus requiring less torque of the motors. Inefficient gear ratios require higher torque
Rollers per panel : 4 rollers per panel allows weight distribution for smooth, quiet operation, no binding
out of the motor, thus requiring larger motors. Please note the power consumption difference note above. The power consumption differenceis quite large as noted above. The difference exists because very little gear reduction is being used by the Stanley drive train requiring moretorque out of the motor, consuming six times more power than the meticulously engineered record drive train. In addition to the increasedpower consumption, the motor life is significantly reduced with the exponential amount of torque required due to the lack of gear reduction
Bottom Guide Design : Record's bottom pin guide is designed to reduce friction extending the life of the guide and threshold track
3/6/06 1
AAADM
American Association of Automatic Door Manufacturers
AUTOMATIC SLIDING DOOR
OWNER'S MANUAL
Distributed by:
Contents Section Page Caution 2 To Our Customers 2 Service Availability 3 Compliance with Safety Standards 3 What You Should Know 3 Daily Safety Check 4 Operation 7 Limited Warranty 8
3/6/06 2
CAUTION
An Improperly Adjusted Door can cause injury and/or equipment damage. Inspect door operation daily using safety checklist in Owner's Manual and at door. Have door adjusted as described in
Owner's Manual. Safety devices should be in place and
operational. Have door inspected at least annually by an AAADM certified inspector.
In the following manual, the word:
Caution means that injury or property damage can result from failure to follow instructions.
Note is used to indicate important steps to be followed or important differences in equipment.
To Our Customers
The purpose of this manual is to familiarize you with your automatic door system. It is essential that you "know your system" and that you recognize the importance of maintaining your door system in compliance with the industry standards for safety.
It is your responsibility, as owner or caretaker of the equipment, to inspect the operation of your door system on a daily basis to ensure that it is safe for use by your invitees, customers, or employees.
This manual will provide you with a description of the operation and maintenance requirements of your door. It also provides the instructions for the Daily Safety Check.
Should the door fail to operate as prescribed in the Daily Safety Check, or at any other time for any other reason, do not attempt to repair or adjust the door. Call an AAADM Certified service technician. These technicians are trained to service your door in accordance with applicable industry safety standards.
3/6/06 3
Service Availability
Automatic door products are distributed through a nationwide network of authorized automatic door suppliers for sales, installation, and service.
Should you need service on your door system, consult the respective door manufacturer or its authorized representative. Compliance with Safety Standards
Your door system was designed to the latest operating and safety standards. In order to ensure the continued safe operation of your door, it is important that:
- Your door system be maintained in compliance with the standards of the industry.
- Proper decals and labels be applied and maintained on your doors. If decals are removed or cannot be read, request labels to be replaced when calling for service.
- Automatic doors should be checked by an AAADM certified inspector at least annually. AAADM, the American Association of Automatic Door Manufacturers, has established a program to certify automatic door inspectors. Through this program, the inspectors are trained to check your door systems for compliance with the appropriate version of the American National Standards Institute standard ANSI/BHMA A156.10. What You Should Know
Be sure that an automatic door supplier has provided the following for each door:
1. Instruction on how to conduct the Daily Safety Check *(by walk-through example).
2. Location of function switches and instruction in their use.
3. Circuit breaker or main power disconnect location for each door system.
4. Number to call for service or questions about your system if you are uncertain of any condition or situation.
5. AAADM inspection form or a work order signed by an AAADM certified inspector.
6. A completed Annual Compliance Inspection label, located at the bottom of the Safety Information label affixed to the door.
7. Warranty information for each door.
Note: If there are any problems, or if you are unsure about the safe performance of the door, discontinue door operation immediately and secure the door in a safe manner. Call your authorized automatic door professional for repairs.
*Note: AAADM Daily Safety Check videos are available. Contact an automatic door supplier
or AAADM. Automatic sliding doors are installed in a variety of combinations.
• Single or Bi-parting • Sliding Door Swings out in emergency with fixed sidelite • Sliding Door Swings out in emergency and sidelite also swings out • One-Way Traffic or Two-Way Traffic • Activated by Floor Mat, Sensors, or Push Switches
They always require a Safety Zone to cover the area in or near the door travel.
3/6/06 4
Daily Safety Check (All figures and diagrams are for purposes of illustration only) Perform the following safety checks daily on each automatic sliding door to ensure your customers' safety and your own protection. Perform these tests while traffic is restricted from all detection and sensing zones.
Sensor Activation
1. Check electronic sensor by walking toward the door opening at a moderate speed. The door should start opening when you are about four feet from the door, should slide open smoothly, and stop without impact. Repeat on other side of opening. Move slowly through the door opening (6 inches per second). The door should remain open. (See Figures 1 and 2) NOTE: If your door is set up for one-way traffic, the sensor on the side not intended for approach should be active until the door is within 6 inches of fully closed. The sensor should re-open the closing door if a person is detected a minimum of 24 inches from the door.
2. Step out of the sensor zone. After a brief time delay (at
least 1 1/2 seconds) the door should slide closed smoothly and should close fully without impact. Doors should be adjusted so they do not close faster than 1 foot per second.
3. Observe traffic routing to the door. Plan traffic routing so
persons will approach the door straight on and not from an angle.
4. Walk parallel to the door face and towards the center of the
door opening to check that the detection pattern is at least as wide as the door opening. This test should be performed within approximately 12 inches from the door face. Repeat this test in both directions.
5. Open the door. Crouch motionless in threshold for at least
10 seconds to check safety zone. The door should not close.
Floor Mat Activation 1. Step on the "opening" (activating) mat in several places.
Door should slide open smoothly and stop without impact. (See Figure 3)
Figure 1
Figure 2
Figure 3
3/6/06 5
2. Step through the doorway onto the mat on the other side. Door should remain fully open without interruption. Note: If there is more than one mat on each side, each mat should be tested.
3. Step off the mat. After a brief time delay (at least 1 1/2
seconds), the door should close slowly and smoothly without impact. Doors should be adjusted so they do not close faster than 1 foot per second.
4. Check the mat molding and threshold. It should be
complete and secured with all screws required.
General Safety Pay attention to the following general safety items and conduct checks periodically where noted.
1. Signage. Door should have decals properly displayed. There
should be decals that include the statements: "AUTOMATIC DOOR" (in letters 1/2 in. high, minimum) and "IN EMERGENCY - PUSH TO OPEN". An adjacent sidelite or wall should have a “STAND CLEAR” or similar decal in the slide path of the door (See Figures 4, 5, 6, 7, and 8 for examples of some decals that may be used.). An AAADM safety information label should be affixed to the door frame in a visible, protected location.
2. Closing Speed. The closing time of the door must not be less
than the minimum time as shown in the following table. This closing time is taken from full open to a point six inches from fully closed. Example: If a single slide door with a nominal opening of 36 inches closes in 2.3 seconds it is too fast and must be slowed down. If it closes in 3.0 seconds it is in compliance.
3. Force to prevent the door from closing should not exceed 30 pounds. This can be measured with a force gauge.
Maximum Closing Speed - 1 Foot Per Second
Nominal Door Opening
Single Slide Bi-Part
Minimum Closing Time to
Within 6 inches of Closed
48" 2 Sec 60" 2½ Sec
36" 72" 3 Sec 42" 84" 3½ Sec 48" 96" 4 Sec
Figure 4
Figure 7
AUTOMATIC DOOR
IN EMERGENCYPUSH TO OPEN
Figure 6
Figure 5
STAND CLEAR
Figure 8
3/6/06 6
4. Activating Switch. (Knowing Act) Doors equipped with a manual operate switch shall, when activated, hold the door open for five seconds minimum after release of activating switch. Doors equipped with manual activating switch shall have a decal as follows: “AUTOMATIC DOOR. ACTIVATE SWITCH TO OPERATE”. The sign should be visible from both sides of the door or the side with the knowing act switch if there is only one. (See Figure 9)
5. Emergency Breakout. Test by manually pushing door at
lock area in direction of emergency exit. Release door. The door should either stop operation or spring to closed position. Make sure door panel or panels are properly re-latched. If the door is equipped with breakaway sidelites, door operation should stop when sidelites are broken out. (See Figure 10).
6. Housekeeping. Be sure floor guides are kept clean and free of any debris which could prevent proper door slide. Check the door area for tripping or slipping hazards. Check all door panels for damage. Make sure that all hardware and overhead covers are properly secured. There should be no bulletin boards, literature racks, merchandise displays, or other attractions that would interfere with the use of the door or invite people to stop or stand in the door area.
7. Traffic Patterns. Observe traffic patterns. Plan routing so
people enter and exit in a straight approach, directly towards the center of the door opening.
IF YOU HAVE A PROBLEM, TURN OFF THE DOOR OPERATING EQUIPMENT AND CALL AN AUTOMATIC DOOR SUPPLIER TO MAKE PROMPT REPAIRS.
AUTOMATIC DOOR ACTIVATE SWITCH
TO OPERATE
Figure 9
Figure 10
OWNER’S MANUAL - SERIES 5100 CONTROL PANEL
The Series 5100 Sliding Door System includes an electronic control panel to select the operating mode ofthe door, and provide feedback on the door status. Included are five pushbutton / keys-
- +
OPEN
E
C
OFF AUTO
PROG EXIT
AUTO
The control panel includes a backlit display providing confirmation of the above modeselection, reminders of safety checks and phone numbers, and will additionally indicatewhen the system has an abnormal operating status. Abnormal status indication is in theform of a short text description of the anomaly. Examples include “Emergency Breakout”“Safety Beam actuated > (for more than) 60 sec.”, “Obstruction”, etc. The user may beable to resolve some issues without requiring a service call. Certain door status will re-quire an authorized technician to service the door, and their phone number can be ac-cessed by momentarily switching the door OFF, then back on (AUTO, EXIT, or OPEN),and the phone number will momentarily display.
Using the above examples -
STOP/BREAKOUT
47
EMERGENCY
31
4759
ELS active>60s
Safety Beam
47
Obstruction
63
Emergency Breakout - indicates one of the door panels has been brokenout and has not been fully reset into the closed position. Each doorpanel should be inspected and closed properly.
Additional screens provide similar information concerning the door sensors and operator components. A smallkey displayed on the left side of the screen indicates a remote override switch has disabled the panel. If themessage “Control Panel can’t override” is displayed when attempting to change operator modes, a secondcontrol panel (or remote control interface) is connected to the door and has priority.
Sep’07
turns off automatic motion and allows the door to be moved manuallyNote 1: Depending on door configuration, this may close & the door.Note 2: When in the ED mode, pressing the OFF key a second time will momentarilyopen the door to allow egress; after an adjustable delay, the door will close and return to the
ED mode.
OFF .
LOCK
OFF/LOCK
OFF/LOCK
enables automatic operation with response for both ingress and egress.AUTO
enables automatic operation for egress traffic only.EXIT
automatically opens the door and remains openOPEN ; pressing a second time will place the door inmode allowing easy re-positioning of the door.Manual
selects the percentage of opening for the above modes. When pressed momentarily, the automatic opening is changed from a full opening to a reduced opening, indicated on the display bythe additional phrase “PART’L” and small arrows above the mode icon. Press the key a 2nd timeto revert back to full open operation. If the key is pressed and held for 8 seconds, a bar graph isdisplayed indicating the percentage of full opening that will be used in Partial opening. To changethe partial open width, press the AUTO key to increase, or the OFF key to decrease The bargraph will indicate the revision. When finished, press the “record” key to select the new setting.
PROG -
.
OFFPROG+ +
To re-enable the keypad, repeat the above sequence.
The control panel can be “locked”, preventing unauthorized use, by pressing the key sequence -
A small square with an “X” will appear on the left of the display.
7
Safety Beam > 60s(econds) - indicates one of the four safety beam heads (two located oneach side of the opening) has been blocked. Remove objects that may be obstructinga clear line-of-sight between opposing beam heads.
Obstruction - indicates the door(s) has encountered significant resistance in either openingor closing and cannot move without exceeding code limited forces. Inspect the bottomguides, weatherstripping, etc., around the perimeter of the door and in the door’s pathof motion. Note: After an obstruction ocurrs, the next operation of the door will approachthe obstruction point at a reduced speed; normal speed is resumed after traveling throughthe obstruction point without impediment.
To reset the door operator, press the button for 8 seconds. The screen at right will appear.
Press the button again to initiate a software reset; normal operation should resume in a
few seconds. If not, contact your local record dealer
Reset control?
No
Yes
Warranty
record-USA DOOR SYSTEMS WARRANTY
We warrant to the buyer that record-usa door systems have been manufactured from high-grade materials with first-class workmanship. Subject to the other conditions of this Warranty, if any parts of our own manufacture prove defective under normal use and service within two years of installation (6100 swing series within one year of installation), we shall repair or re- place such parts free of cost. If any equipment or parts not of our own manufacture are utilized in connection with this door operator and equipment, we shall assume responsibility and liability for defects only to the extent of such adjustment as the manufacturer thereof makes to us. It is the responsibility of the buyer to furnish all labor and expense necessary to replace the part. The warranty shall not extend beyond two years from the date of purchase regardless of any replacements, which may be made.
Our obligations under this Warranty are conditional upon the buyers having (1) given us prompt written notice of alleged defects, and
(2) upon our request, returned the allegedly defective item(s) within 30 days to our works in Monroe, North Carolina, freight prepaid, for our inspection.
We shall have no obligation or liability, under this Warranty or otherwise, in the event of 1) improper installation or application of product; 2) misuse, neglect or accident; and 3) installation, service, repair or alteration in any way by any person not expressly
authorized in writing for such purpose. However, in no case shall we have any obligation or liability beyond two years after original installation or any replace- ment or repairs that may be made.
We reserve the right, without obligation, to inspect all installations of record door operators and equipment for the protection of both the end user and ourselves.
In no event shall we have any obligations or liability, under this Warranty or otherwise, resulting in whole or in part for damage to defects in the door operator or equipment caused by abuse, misuse, malicious mischief, acts of God, casualty, improper handling or the negligence of the owners or others. Nor shall we have any obligations or liability for any loss, cost or expense incurred in the repair or replacement of the door operator or equipment except on express written authority from our office in Monroe, North Carolina.
The buyers sole remedy against us for any alleged defects in the record door operator or equipment shall be as provided in this Warranty. We hereby disclaim all other obligations and liability for damages, including any incidental consequential damages. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
This Warranty may not be changed, expanded or modified in any way except in writing, signed by our duly authorized representative.
record-USA • 4324 Phil Hargett Court, Monroe, NC 28110 • PO Box 3099 • Monroe, NC 28111-3099 (704) 289-9212 Voice • (800) 438-1937 WATTS • (704) 289-2024 FAX • www.record-usa.com