PASERVICE MANUALNTSCLC58/LC58E

50VF820/LC58; 50VG825/LC58E 55VF820/LC58; 55VG825/LC58E 60VF820/LC58; 60VG825/LC58E

No. 0210

R/C: CLU-3851WL; CLU-4352UG2

TO GO TO A CHAPTER, CLICK ON ITS HEADING BELOW TO GO TO A CHAPTER, CLICK ON ITS HEADING BELOW

CONTENTSIMPORTANT SAFETY INSTRUCTIONS .............................................................................. 2 SERVICING PRECAUTIONS ............................................................................................. 4 AGENCY REGULATORY INFORMATION........................................................................... 9 FEATURES & SPECIFICATIONS ...................................................................................... 10 GENERAL INFORMATION..................................................................................................13 REMOTE CONTROL GUIDE ...............................................................................................26 SERVICE ADJUSTMENTS .................................................................................................31 TROUBLESHOOTING FLOW CHART................................................................................88 BLOCK DIAGRAM .............................................................................................................96 CONNECTION DIAGRAM .................................................................................................98 ASSEMBLY DRAWINGS .........................................................................................................99 FINAL WIRING DIAGRAM ..................................................................................................................107 QUICK DISASSEMBLY GUIDE ..........................................................................................112 WAVEFORMS ..................................................................................................................................123 DC VOLTAGE TABLES ....................................................................................................126 CIRCUIT SCHEMATIC DRAWING ......................................................................................129 PRINTED CIRCUIT BOARDS ...........................................................................................152 REPLACEMENT PARTS LIST .........................................................................................170 QUICK REFERENCE PARTS LIST (IC & UNIT) ..............................................................188

CAUTION:

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Before servicing this chassis, it is important that the service technician read the IMPORTANT SAFETY INSTRUCTIONS in this service manual.

SAFETY NOTICE USE ISOLATION TRANSFORMER WHEN SERVICING Components having special safety characteristics are identified by a ! on the schematics and on the parts list in this Service Data and its supplements and bulletins. Before servicing the chassis, it is important that the service technician read and follow the Important Safety Instructions in this Service Manual.

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

LCD REAR PROJECTION TELEVISIONAUGUST 2005 HHEA-MANUFACTURING DIVISION

LC58/LC58E

IMPORTANT SAFETY INSTRUCTIONS

NOTICE: Comply with all cautions and safety-related notes located on or inside the cabinet and on the chassis or optic unit. WARNING: Since the chassis of this receiver is connected to one side of the AC power supply during operation, whenever the receiver is plugged in service should not be attempted by anyone unfamiliar with the precautions necessary when working on this type of receiver. The following precautions should be observed: 1. Do not install, remove, or handle the optic unit in any manner unless shatterproof goggles are worn. People not so equipped should be kept away from the optic unit while handling. 2. When service is required, an isolation transformer should be inserted between power line and the receiver before any service is performed on a HOT chassis receiver. 3. When replacing a chassis in the receiver, all the protective devices must be put back in place, such as barriers, nonmetallic knobs, adjustment and compartment cover-shields, isolation resistors, capacitors, etc. 4. When service is required, observe the original lead dress. 5. Always use the manufacturers replacement components. Critical components as indicated on the circuit diagram should not be replaced by another manufacturers. Furthermore, where a short circuit has occurred, replace those components that indicate evidence of overheating. 6. Before returning a serviced receiver to the customer, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without danger of electrical shock, and be sure that no protective device built into the receiver by the manufacturer has become defective, or inadvertently defeated during servicing. Therefore, the following checks should be performed for the continued protection of the customer and service technician. Leakage Current Cold Check With the AC plug removed from the 120V AC 60Hz source, place a jumper across the two plug prongs. Using an insulation tester (DC500V), connect one lead to the jumpered AC plug and touch the other lead to each exposed metal part (antennas, screwheads, metal overlays, control shafts, etc.), particularly any exposed metal part having a return path to the chassis should have a minimum resistor reading of 2.4M and a maximum resistor reading of 5.2M . Any resistance value below or above this range indicates an abnormality which requires corrective action. An exposed metal part having a return path to the chassis will indicate an open circuit.

Leakage Current Hot Check Plug the AC line cord directly into a 120V AC 60Hz outlet (do not use an isolated transformer for this check). Turn the AC power ON. Using a Leakage Current Tester (Simpsons Model 228 or equivalent), measure for current from all exposed metal parts of the cabinet (antennas, screwheads, overlays, control shafts, etc.) particularly any exposed metal part having a return path to the chassis or to a known earth ground (water pipe, conduit, etc.). Any current measured must not exceed 0.5 MIU.

DEVICE UNDER TEST

LEAKAGE CURRENT TESTER

(READING (READING SHOULD NOT SHOULD NOT BE ABOVE BE ABOVE 0.5 MIU) 0.5 mA)

+TEST ALL EXPOSED METAL SURFACES

-

2-WIRE CORD EARTH GROUND ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUS AS REQUIRED)

AC LEAKAGE TEST ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE RECEIVER TO THE CUSTOMER. AC CORD POLARITY This check is based on the UL standard. Use the jigs specified by the production technology section. The GND side (wider blade) of the AC power cord should be connected to KKX1.L901

C901

R901

KKX1 2 PA F901 PPT1 WHITE side

X901

GND side

Tester

TABLE OF CONTENTS

2

LC58/LC58E

PRODUCT SAFETY NOTICEMany electrical and mechanical parts in HITACHI television receivers have special safety-related characteristics. These are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified with an ! mark in the schematics and parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the HITACHI-recommended replacement component, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Production safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current HITACHI Service Manual. A subscription to, or additional copies of HITACHI Service Manuals may be obtained at a nominal charge from HITACHI Sales Corporation. Ultraviolet Radiation OPTIC UNIT: The primary source of Ultraviolet Radiation in this receiver is the optic unit. The optic unit utilized in this chassis is specially constructed to limit Ultraviolet Radiation emissions. For continued Ultraviolet Radiation protection, the replacement optic unit must be the same type as the original HITACHI-approved type. Service Personnel - WARNING Eye damage may result from directly viewing the light produced by the lamp used in this product. Always turn off lamp before opening optic unit. Ultraviolet radiation eye protection required during servicing. When troubleshooting and making test measurements in a receiver with an excessive high voltage problem, avoid being unnecessarily close to the optic unit and the high voltage component. Do not operate the chassis longer than is necessary to locate the cause of excessive voltage. When servicing or handling circuit boards and other components which contain lead in solder, avoid unprotected skin contact with solder. Also, when soldering do not inhale any smoke or fumes produced.

SAFETY NOTICE USE ISOLATION TRANSFORMER WHEN SERVICINGComponents having special safety characteristics identified by ! on the parts list in this service manual and its supplements and bulletins. Before servicing this product, it is important that the service technician read and follow the Safety Precautions and the Product Safety Notices in this Service Manual. For continued ultraviolet protection, replace optic unit with original type or HITACHI equivalent type.

POWER SOURCEThis television receiver is designed to operate on 120 Volts/60Hz, AC house current. Insert the power cord into a 120 Volts/60Hz outlet. NEVER CONNECT THE TV TO OTHER THAN THE SPECIFIED VOLTAGE OR TO DIRECT CURRENT. CAUTION! The following symbol near the fuse indicates fast operating fuse (to be replaced). Fuse ratings appear within the symbol. Example:

125V 6A F101 F901 The rating of fuse F101 is 6.0A-125V. Replace with the same type of fuse for continued protection against fire. NOTE: The lamp in this product contains Mercury. Dispose of properly in accordance with applicable environmental laws. For Recycling and Disposal information, contact your respective governmental agencies or the Electronic Industries Alliance at www.eiae.org (in the U.S.) or Electronic Product Stewardship Canada at www.epsc.ca (in Canada).

This Service Manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void warranty. Consumers should not risk trying to do the necessary repairs and should refer to a qualified service technician. WARNING Lead in solder used in this product is listed by the California Health and Welfare agency as a known reproductive toxicant which may cause birth defects or other reproductive harm (California Health and Safety Code, Section 25249.5).

3

LC58/LC58E

SERVICING PRECAUTIONSCAUTION: Before servicing instruments covered by this service data and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 2 of this publication. NOTE: If unforseen circumstances create conflict between the following SERVICING PRECAUTIONS and any of the SAFETY INSTRUCTIONS on page 2 of this publication, always follow the SAFE TY INSTRUCTIONS. Remember: Safety First. General Servicing Guidelines 1. Always unplug the instrument AC power cord from the AC power source before: a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly. b. Disconnecting or reconnecting any instrument electrical plug or other electrical connection. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. Use only a grounded-tip soldering iron to solder or desolder ES devices. Use only an anti-static type solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES device. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)

2.

3.

4.

c.

5.

6.

2.

Do not spray chemicals on or near this instrument or any of its assemblies. Unless specified otherwise in these service data, clean electrical contacts by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive applicator: 10% (by volume) Acetone and 90% (by volume) ispropyle alchohol (90%-99% strength). CAUTION: This is a flammable mixture. Unless specified otherwise in these service data, lubrication of contacts is not required. Do not defeat any plug/socket B+ voltage interlocks with which instruments covered by this service data might be equipped. 7.

3.

8.

4.

5.

Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat-sinks are correctly installed. Always connect the test instrument ground lead to the appropriate instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last. Use with this instrument only the test fixtures specified in this service data. CAUTION: Do not connect the test fixture ground strap to any heatsink in this instrument.

6.

7.

Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity.

TABLE OF CONTENTS

4

LC58/LC58E

SERVICING PRECAUTIONSGeneral Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range 500F to 600F. 2. Use an appropriate gauge of resin-core solder composed of 60 parts tin/40 parts lead. Keep the soldering iron tip clean and well-tinned. Thoroughly clean the surfaces to be soldered. Use a small wirebristle (0.5 inch or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. Use the following desoldering technique. a. Allow the soldering iron tip to reach normal temperature (500F to 600F). b. Heat the component lead until the solder melts. Quickly draw away the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 3. 2. Draw away the melted solder with an anti-static suction-type sol der removal device (or with solder braid) before removing the IC.

Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to areas.)

3. 4.

5.

Small-signal Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a U shape the end of each of three leads remaining on the circuit board. Bend into a U shape the replacement transistor leads. Connect to replacement transistor leads to the corresponding leads extending from the circuit board and crimp the U with long nose pliers to insure metal to metal contact, then solder each connection.

3. 4.

6.

Use the following soldering technique. a. Allow the sodering iron tip to reach normal temperature (500F to 600F). b. First, hold the soldering iron tip and solder strand against the component lead until the solder melts. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil or components. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.

Power Output Transistor Devices Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heatsink mounting screw (if so equipped). Carefully remove the transistor from the circuit board. Insert new transistor in circuit board. Solder each transistor lead, and clip off excess lead. Replace heatsink.

c.

3. 4. 5. 6.

d.

Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possilbe to diode body. 2. Bend the two remaining leads perpendicularly to the circuit board. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. Securely crimp each connection and solder it. Inspect (on the circuit board copper side) the solder joints of the two original leads. If they are not shiny, reheat them and, if necessary, apply additional solder.

3.

Use Soldering Iron to Pry Leads

4. 5.

IC Removal/Replacement Some Hitachi unitized chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

5

LC58/LC58E

SERVICING PRECAUTIONSFuses and conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of circuit board hollow stake. 2. Securely crimp leads of replacement component around stake 1/8 inch from top. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board, to prevent excessive component temperatures.

At Other Connections Use the following technique to repair defective copper pattern at

3.

DEFECTIVE COPPER REMOVED

Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board, causing the foil to separate from, or lift-off the board. The following guidelines and procedures should be followed whenever this condition is encountered. In Critical Copper Pattern Areas High component/copper pattern density and/or special voltage/current characteristics make the spacing and integrity of copper pattern in some circuit board areas more critical than in others. The circuit foil in these area is designated as Critical Copper Pattern. Because Critical Copper Pattern requires special soldering techniques to ensure the maintenance of reliability and safety standards, contact your Hitachi personnel. At IC Connections To repair defective copper pattern at IC connections, use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections.) 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary.) 2. Carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

Insulated Jumper Wire connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both wire sides of the pattern break and locate the nearest component directly connected to the affected copper pattern. Connect insulated 20-gauge jumper wire from the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so that it does not touch components or sharp edges.

3.

BARE JUMPER WIRE

Frequency Synthesis (FS) Tuning Systems 1. Always unplug the instrument AC power cord before disconnecting or reconnecting FS tuning system cables and before removing or inserting FS tuning system modules. 2. The FS tuner must never be disconnected from the FS tuning control module while the power is applied to the instrument. When troubleshooting intermittent problems that might be caused by defective cable connection(s) to the FS tuning system, remove the instrument AC power as soon as the defective connector is found and finish confirming the bad connection with a continuity test. This procedure will reduce the probability of electrical overstress of the FS system semi-conductor components.

CRIMP AND SOLDER

3. Install Jumper Wire and Solder 3. Bend a small U in one end of a small-gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. Route the jumper wire along the path of the cut-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area, and clip off any excess jumper wire.

4.

6

LC58/LC58E

SERVICING PRECAUTIONSNOTE: These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose.

Leadless Chip Components (surface mount)Chip components must be replaced with identical chips due to critical foil track spacing. There are no holes in the board to mount standard transistors or diodes. Some chip capacitor or resistor board solder pads may have holes through the board, however the hole diameter limits standard resistor replacement to 1/8 watt. Standard capacitors may also be limited for the same reason. It is recommended that identical chip components be used. . Chip resistors have a three digit numerical resistance code -1st and 2nd significant digits and a multiplier. Example: 162 = 1600 or 1.6K resistor, 0 = 0 (jumper). Chip capacitors generally do not have the value indicated on the capacitor. The color of the component indicates the general range of the capacitance. Chip transistors are identified by a two letter code. The first letter indicates the type and the second letter, the grade of transistor. Chip diodes have a two letter identification code as per the code chart and are a dual diode pack with either common anode or common cathode. Check the parts list for correct diode number.

How to Replace Flat-lC Required Tools Soldering iron iron wire or small awl De-solder braids Magnifier 1. Remove the solder from all of the pins of a Flat-lC by using a de-solder braid.Flat-IC De-Solder Braid Soldering Iron

2.

Put the iron wire under the pins of the Flat-lC and pull it in the direction indicated while heating the pins using a soldering iron. A small awl can be used instead of the iron wire.Iron Wire Awl

Pull

Soldering Iron

Soldering Iron

Component Removal1. 2. 3. Use solder wick to remove solder from component end caps or terminals. Without pulling up, carefully twist the component with tweezers to break the adhesive. Do not reuse removed leadless or chip components since they are subject to stress fracture during removal. Put a small amount of solder on the board soldering pads. Hold the chip component against the soldering pads with tweezers or with a miniature alligator clip and apply heat to the pad area with a 30 watt iron until solder flows. Do not apply heat for more than 3 seconds

3.

Remove the solder from all of the pads of the FlatlC by using a de-solder braid. SolderingIron De-Solder Braid Flat-IC

Chip Component Installation1. 2. 4.

Position the new Flat-lC in place (apply the pins of the Flat-lC to the soldering pads where the pins need to be soldered). Properly determine the Polarity Symbol positions of the soldering pads and pins by correctly aligning the polarity symbol.

Chip ComponentsTYPE

5.SOLDER CAPS

C

GRADE

Solder all pins to the soldering pads using a fine tipped soldering iron.

B E

TRANSISTOR

CAPACITOR 1ST DIGIT

COMMON CATHODE

2ND DIGIT MULTIPLIER = 1600 = 1.6K

Solder

Soldering Iron

6.

ANODES MH DIODE

SOLDER CAPS RESISTOR

Check with a magnifier for solder bridge between the pins or for dry joint between pins and soldering pads. To remove a solder bridge, use a de-solder braid as shown in the figure below.De-Solder Braid Bridge Solder Soldering Iron

7

LC58/LC58E

Information for service about lead-free solder IntroductionHitachi introduced lead-free solder to conserve the "Earth Environment". Please refer to the following before servicing. (1) Characteristic of lead-free solder Melting point of lead free solder is 40-50oC higher than solder containing lead.

(2) Solder for service Following composition is recommended. " Sn - 3.0Ag - 0.5Cu " , or " Sn - 0.7 Cu " Lead solder can be used, but there is a possibility of failure due to insufficient strength of the solder.

Caution when using solder containing lead. Please remove previous solder as much as possible from the soldering point. When soldering, please perfectly melt the lead-free solder to mix well with the previous solder. (3) Soldering iron for lead-free solder. Melting point of lead-free solder is higher than solder containing lead. Use of a soldering tool "with temperature control" and "with much thermal capacitance" is recommended. (Recommended temperature control : 320oC - 450oC) Recommended temperature PWB with chip parts PWB without chip parts Chassis, metal, shield etc. (4) Identification of lead-free PWB 2004 models 2005 models >> lead-free solder is introduced >> lead-free solder apply

320oC +/- 30oC 380oC +/- 30oC 420oC +/- 30oC

On lead-free PWB, "F" is added at the beginning of stamp on PWB. (e.g. F LC58)

8

LC58/LC58E

Useful InfoPLUG AND PLAYThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Cable Compatible Television Apparatus- Tlvision cblocompatible, Canada. This Plasma Television receiver will display television closed captioning, ( paragraph 15.119 of the FCC rules. or ), in accordance with

AGENCY REGULATORY INFORMATION

Federal Communications Commission NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help.

ModificationsThe FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi Home Electronics (America), Inc. may void the users warranty.

CablesConnections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Any cables that are supplied with the system must be replaced with identical cables in order to assure compliance with FCC rules. Order Hitachi spares as replacement cables.

In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895; 6,418,556; 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121. Gemstar-TV Guide International Inc. and/or its related affiliates are not in any way liable for the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system and cannot guarantee service availability in your area. In no event shall Gemstar-TV Guide International, Inc. and/or its related affiliates be liable for any damages in connection with the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system.

TABLE OF CONTENTS

9

LC58/LC58E

Features and SpecificationsFEATURES: Superfine Picture Quality; 1280 Line Horizontal Resolution Remote (Controls many PVR/VCR brands, cable boxes, satellite boxes, and other audio equipment). New Easy-to-Use (3-Language) On-Screen Menu Full Set of Input Jacks, including S-Video COMPONENT VIDEO: Y-PB/PR Six Aspect Modes Closed Caption Decoder 2-Tuner Picture in Picture 2 Antenna Inputs (Either for Analog/Digital) Video Input Sensor HDMI (High Definition Multimedia Interface) (High Bandwidth Digital Content Protection V1.1 compatible). Digital Audio Output (Dolby Digital and PCM) 3 Dimensional Y/C Comb Filter Compatible with 1080i, 720p, 480p and 480i input signals. CableCARDTM compatible - Contact your local cable operator for more information. Technology. Licensed by BBE Sound, Inc. under USP5510752 and 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc. Manufactured under license from BBE Sound, Inc. Technology. SRS and symbol are trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS Labs, Inc. Technology. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Technology HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. INPUTS: Power Input........................................AC 120V, 60Hz Stand-by Power..............................Less than 1 Watt Power Consumption - Refer to rear panel at the back of the T.V. Antenna input impedance .............................75 Ohm Channel coverage VHF-Band .....................................................2 13 UHF-Band...................................................14 69 CATV Band ........................................1 135, A I Video ..............................................1.0Vp-p, 75 Ohm S-Video Luminance (Y) .............................1.0Vp-p, 75 Ohm Chrominance (C) .....................0.286Vp-p, 75 Ohm Component Video Luminance (Y) .............................1.0Vp-p, 75 Ohm Chrominance (PB/PR) ..................0.7Vp-p, 75 Ohm Audio input Impedance ...............................47k Ohm Average input level ...................................470mVrms HDMI.....................................................HDMI 19 PIN

OUTPUTS: Video ..............................................1.0Vp-p. 75 Ohm Audio (Fixed) ..............................470mVrms, 1k Ohm S-Video Luminance (Y) .............................1.0Vp-p, 75 Ohm Chrominance (C) .....................0.286Vp-p, 75 Ohm Optical Out (Digital Audio) ..........1 optical connector

Dimensions: 50VF820 55VF820 60VF820 50VG825 55VG825 60VG825 Height (in.) 28 11/16 (mm) 728.0 Width (in.) 55 3/8 (mm) 1,407.0 Depth (in.) 16 6/16 (mm) 415.8 Weight (lbs.) 110.2 (kg) 50.0 31 1/8 790.0 59 7/8 1,520.0 17 3/4 450 94.1 42.7 33 9/16 853.0 64 1/8 1,629.0 19 1/16 483.8 132.3 60 28 11/16 728.0 55 3/8 1,407.0 16 6/16 415.8 110.2 50.0 31 1/8 790.0 59 7/8 1,520.0 17 3/4 450 94.1 42.7 33 9/16 853.0 64 1/8 1,629.0 19 1/16 483.8 132.3 60

NOTE: Due to improvements, specifications in this operating guide are subject to change without notice.

TABLE OF CONTENTS

10

LC58/LC58E

SPECIFICATIONS

2.2 A/V TERMINALSNo. 1 2 3 4 5 6 7 8 9 10MODEL NAME

60VG825 60VF820 55VG825 55VF820 50VG825 50VF820

A/V In 2 2 2 2 2 2

S-video COMP In In 2 2 2 2 2 2 2 2 2 2 2 2

HDMI In 1 1 1 1 1 1

REAR Monitor Monitor Out S Out 1 1 1 1 1 1 1 1 1 1 1 1

A Out Cent In *1 L(mono) 1 1 1 1 1 1 1 1 1 1 1 1

ANT In 2 2 2 2 2 2

Optical Out

11 1 1 1 1

MM Card 1 1 1 1 1 1

REAR No. 1 2 3 4 5 6 7 8 9 10MODEL NAME

60VG825 60VF820 55VG825 55VF820 50VG825 50VF820

POD Card 1 1 1 1 1 1

IEEE 1394

A/V In 1 1 1 1 1 1

FRONT (or SIDE) S-video Photo In (USB) 1 1 1 1 1 1

1 1 1 1 1

Remark: *1 Monitor out and Audio to HiFi share one terminal and switched by user menu. See 5.9 Terminals and other function about the electrical specifications.

11

LC58/LC58E

SPECIFICATIONS2.3 STRUCTURAL DIMENSIONS No. 1 2 3 4 5 6 7 8 9 10 Model name 60VG825 60VF820 55VG825 55VF820 50VG825 50VF820 Width (mm) 1629 1629 1518 1518 1407 1407 Height (mm) 853 853 791 791 728 728 Depth (mm) 484 484 448 448 416 416 Weight (kg) 53 53

43 43

2.4 MAIN PARTS (1) LCD panel LC5x occupies 3 LCD panels (for Red, Green and Blue color). No. Item Description Blue: L3D07H-51G01B / L3D07H-52G01B 1 Product name Red: L3D07H-51G01R / L3D07H-52G01R Green: L3D07H-51G01G / L3D07H-52G01G 2 System type TFT Active matrix 3 Pixels 1284 (H) x 724 (V) 4 Panel size 0.7 5 Dot pitch 12 m 6 Life time More than 20,000h (@Ta 25C, worst UV filter combination) LCD panel is UV light sensitive device. UV ray which illuminates LCD panel should be cut with three UV filters with 50% cut wavelength of 430nm+430nm+430nm (nominal) and 427nm+427nm+426nm (worst combination). (2) Lamp No. 1 2 3 4 5 6 7 Item Input electricity Manufacture Model name Description 120W Philips UHP 100W/120W 1.0 PH1 P22 UHP lamp 1.0mm More than 6,000h 120W Panasonic

Type Arc length Life time (50% survival rate) 60VG825 Applied model 60VF820 55VG825 55VF820 50VG825 50VF820

UHP lamp 1.3mm More than 6,000h 50V720

Mercury legislation: Apply Hg mark on body

12

LC58/LC58E

GENERAL INFORMATION

How to set up your new HITACHI Projection TelevisionANTENNA Unless your LCD Rear PTV is connected to a cable TV system or to a centralized antenna system, a good outdoor TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc. When using your LCD Rear PTV against a wall, keep it at least 10cm (4 inches) from the wall. NOTE: Your new HDTV has a built-in high definition television signal processor. This television includes a fan to cool the processor. The sound of moving air from the fan is normal and may be noticeable in very quiet environments.

VIEWING The major benefit of the HITACHI LCD Rear PTV is its large viewing screen. To see this large screen at its best, test various locations in the room to find the optimum spot for viewing. The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. Picture brightness decreases as the viewer moves to the left and right of the receiver.3' BEST VERTICAL VIEWING ANGLE

20

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room. If the TVs audio output will be connected to a Hi-Fi systems external speakers, the best audio performance will be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.

0'

5'

10'

15'

20'

R 20' 4" Minimum 50 BEST HORIZONTAL

S

5' 50

10'

15'

20'

VIEWING ANGLE

4" Minimum L

S

IMPORTANT NOTES: 1. Since LCD Rear PTV incorporates a high pressure lamp to display an image, it may take about one minute for the picture to become stable, after the power has been turned on. After extended use, the picture may darken, the color may look unusual, or the lamp goes out, (burns out). You may hear a pop sound when the lamp goes out. These are common characteristics of the lamp, and should not be considered defective. 2. LCD Rear PTV incorporates an advanced cooling fan system to prevent from overheating. If you hear the cooling fan, it should not be considered defective. 3. If you hear a cracking sound from the TV cabinet, it is due to the TVs cabinet expanding and contracting due to room temperature changes. It has no effect on the TVs functions. 4. The LCD Rear PTV cabinet is constructed with all plastic. Make sure to place it on a flat surface. An uneven surface might warp the cabinet and reduce the picture quality.

TABLE OF CONTENTS

13

LC58/LC58E

Hook-up Cables and ConnectorsMost video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable. 300-Ohm Twin Lead Connector This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm). Phono Connector Used on all standard video and audio cables which connect to inputs and outputs located on the televisions rear jack panel and side control panel. F Type 75-Ohm Coaxial Antenna Connector For connecting RF signals (antenna or cable TV) to the antenna jack on the television. S-Video (Super Video) Connector This connector is used on camcorders, VCRs and laserdisc players with an S-Video feature in place of the standard video cable to produce a high quality picture. Optical Cable This cable is used to connect to an audio amplifier with an Optical Audio In jack. Use this cable for the best sound quality. IR Mouse Cable/G-LINK Cable (ProvidedLC58E only) Connect the IR Mouse to the IR Blaster output of your LCD Television when A/V Network is used. You must place the IR Mouse in front of the corresponding IR window of your cable box and VCR. This connection allows your TV, and the TV Guide On ScreenTM system, to control your cable box and/or VCR. USB Cable This cable is used to connect your digital camera to the Photo Input in the side of the LCD television. HDMI Cable This cable is used to connect your external devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection to the TVs HDMI input. ANTENNA CONNECTIONS TO REAR JACK PANEL VHF (75-Ohm) antenna/CATV (Cable TV) When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the CABLE (75-Ohm) terminal. If you have an antenna, connect the coaxial cable to the AIR terminal. VHF (300-Ohm) antenna/UHF antenna When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into the antenna terminal on the TV. When both VHF and UHF antennas are connected Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer.

6

14

LC58/LC58E

GENERAL INFORMATION

Front Panel Controls

Lamp Temp Power

MENU/SELECT

PHOTO INPUT

LC58E only

CHANNEL

INPUT 5 S-VIDEO

INPUT 5 S-VIDEO

CURSOR

VOLUME VIDEO L/MONO INPUT/EXIT AUDIO RVIDEO L/MONO AUDIO R

POWER

MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode. INPUT/EXIT button Press this button to display the input menu, CABLE, AIR, INPUT: 1, 2, 3, 4 and 5. This button also serves as the EXIT button when in MENU mode. CHANNEL selector Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down ( ) and up ( ) buttons when in MENU mode. VOLUME level Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left ( ) and right ( ) buttons when in MENU mode. When the TV power is turned OFF at a volume level 31 or greater, the volume level will default to 30 when the TV is turned ON. However, if it is set to a level 30 or less, the volume level will be at the level it was set when the TV is turned ON. POWER button Press this button to turn the TV on or off. SIDE INPUT JACKS (INPUT 5) Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording. Press the INPUT button and select INPUT 5. If you have mono sound, insert the audio cable into the left audio jack. IR RECEIVER Sensor This is a remote sensor for a better remote control range of response.

15

LC58/LC58E

GENERAL INFORMATION

Front Panel Controls POWER Light

This light is on during normal operation. Light Blinking Slowly (2 seconds): television lamp is cooling down. It takes 12-15 seconds to warm up and about 2 minutes to cool down. TEMP Indicator This light is off during normal operation. If this indicator is lit, the optic unit is too hot. If this indicator is blinking, the cooling fan has stopped. Please call service. The optic unit has an air filter that may become clogged over time. The ternal termperature will increse which will trigger the temperature sensor to display an On-Screen warning. After 5 minutes, the lamp will turn off, then the TV will turn off with the TEMP LED On. LAMP Indicator This light is off during normal operation. If light is lit, the lamp has failed. See page 22-25 for lamp replacement procedure. Consult your Hitachi dealer for proper part. If light is blinking, lamp cover is not assembled securely after replacement.NOTES: 1. INDICATOR INDICATION LIGHT ON LAMP LED BLINKING MEANING NO LAMP LIGHT or BROKEN LAMP WRONG LAMP UNI T ASSEMBLY / LAMP DOOR OPEN Too hot inside the OPTIC unit COOLING FAN STOPPED BEGINNING OF WARM UP AFTER THE POWER ON. NORMAL OPERATIONBEGINNING OF COOL DOWN (FOR 20 SEC.) (TV CANT ACCEPT ANY CODE IN THIS PERIOD EXCEPT BEGINNINGS 5 SEC.)

ACTION Need to replace if LAMP still does not light b y Power On again. Check assembly condition of LAMP UNIT

TEMP LED

LIGHT ON BLINKING

Call for Service

POWER LED

INTERMEDIATE BLINKING (0.5 SEC CYCLE) LIGHT ON SHORT BLINKING (0.3 SEC CYCLE)

LONG BLINKING (1 SEC CYCLE)

COOL DOWN (FOR 6 MINUTES) (TV CAN ACCEPT REMOTE CONTROL AND FRONT BUTTONS)

2. If the LAMP, TEMP, and POWER LED are blinking in the order below, the television is warming up. POWER TEMP LAMP 3. Your Hitachi LCD Rear Projection Television may appear to be OFF when it is set to input 1 ~ input 5 and the video signal is not received from the input jacks. Please make sure the Blue Power light indicator is not lit (OFF) when you are not watching for long lasting performance. Your Hitachi LCD Rear Projection Television has an internal lamp that lights up the TV screen. Make sure to turn off the Power when you do not watch the LCD Rear Projection Television for longer lamp life .

4.

PHOTO INPUT

Insert USB cable from your digital Camera to view your digital still pictures. (Only LC58E)

16

LC58/LC58E

GENERAL INFORMATION

Side Panel Jacks and Connections (LC58 only)The side panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples:

INPUT 5 S-VIDEO

INPUT 5 S-VIDEO

VIDEO L/MONO AUDIO R

VIDEO L/MONO AUDIO R

NOTE: 1. Completely insert connection cord plugs when connecting to side panel jacks. If you do not, the played back picture may be abnormal. 2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable. 3. If you have a mono VCR, insert the audio cable into the left audio jack of your TV.

17

LC58/LC58E

Side Panel Jacks and Connections (LC58E only)The side panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples:

PHOTO INPUT

PHOTO INPUT

INPUT 5 S-VIDEO

INPUT 5 S-VIDEO

VIDEO L/MONO AUDIO R

VIDEO L/MONO AUDIO R

USB Cable

Digital Camera

NOTE: 1. Completely insert connection cord plugs when connecting to side panel jacks. If you do not, the played back picture may be abnormal. 2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable. 3. If you have a mono VCR, insert the audio cable into the left audio jack of your TV.

18

LC58/LC58E

GENERAL INFORMATION

Rear Panel Connections Antenna Input CABLE CATV (Cable TV) input. AIR RF antenna input. NOTE: You may ask your local cable company whether DTV services are available.Upgrade Card

CABLEApparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; and 6,381,747 licensed for limited viewing uses only.

CableCARD(Top of card faces right)Top faces

Audio/Video Inputs 1, 2, 3 and 4 By using the INPUTS button, CURSOR buttons and SELECT button of the remote control you can select each video source. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable into the left audio jack.) NOTE: You may use VIDEO or S-VIDEO inputs to connect to INPUT 1 and 2, but only one of these inputs may be used at a time. Monitor Out These jacks provide fixed or variable audio and video signals which are used for recording. Use the S-Video Output for high quality video output . S-Video Inputs 1 and 2 INPUTS 1 and 2 provide S-Video (Super Video) jacks for connecting equipment with S-Video output capability. Component: Y-PBPR Inputs INPUTS 3 and 4 provide Y-PBPR jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may use composite video signal for both inputs. NOTE: 1. Do not connect composite VIDEO and S-VIDEO to INPUT 1, 2 or 5 at the same time. S-VIDEO has priority over VIDEO input. 2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TVs PB input and the components R-Y output to the TVs PR input. 3. Your component outputs may be labeled Y-CBCR. In this case, connect the component CB output to the TVs PB input and the component CR output to the TVs PR input. 4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs. 5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR jacks. 6. INPUT 3 and INPUT 4 (Y/VIDEO) can be used for composite video and component video input.

HDMI INPUT 1

AIR

Y/ VIDEO

Y/ VIDEO

MONITOR OUT S I V I D E OV I D E O A U D I O

HDMI INPUT 2PB PB

OPTICAL OUTPR PR

Digital Audio

(MONO)

(MONO)

(MONO)

(MONO)

L

TV AS CENTERR

CAUTION

AUDIO TO HI-FI

INPUT 1 INPUT 2 INPUT 3 INPUT 4

HDMI1 (High Definition Multimedia Interface) (INPUT 1) ABOUT HDMI HDMI is the next-generation all digital interface for consumer electronics. HDMI enables the secure distribution of uncompressed high-definition video and multichannel audio in a single cable. Because digital television (DTV) signals remain in digital format, HDMI assures that pristine high-definition images retain the highest video quality from the source all the way to your television screen. HDMI 2 (Input 2) Extra HDMI input. Use the HDMI input for your external devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. NOTE: 1. The HDMI input is not intended for use with personal computers. 2. Only DTV formats such as 1080I, 720P, 480I and 480P are available for HDMI input. Optical Out (Digital Audio) This jack provides Digital Audio Output for your audio device that is Dolby Digital and PCM compatible, such as an audio amplifier. Manufactured under license from Dolby Laboratories. DOLBY and the DOUBLE-D symbol are trademarks of Dolby Laboratories. Upgrade Card This card slot is for future software upgrades. Hitachi will notify you if a software upgrade is required for your TV. In order to receive written notification, please complete and return your warranty card.

19

LC58/LC58E

GENERAL INFORMATION

Rear Panel Connections TV AS CENTER (INPUTS 1-4) These jacks are for stereo amplifiers with center signal output capability. This feature allows the TV speakers to be used as a center speaker. The TV must be set as a center channel by selecting TV AS CENTER on the Internal Speakers Settings of the Audio Menu. CableCARD Slot This slot is for the CableCARD that will be provided by your local cable operator to gain access to chosen cable channels. The CableCARD will allow you to tune digital and high definition cable channels. Please call your local cable operator if this service is available before requesting a CableCARD (also known as Point of Deployment (POD) module). 1. 2. Connect a coaxial cable to cable terminal of the Rear Panel Jacks. Insert the CableCARD into the slot (Top of card should be facing right as shown below).Digital Cable

If the CableCARD is properly installed or not installed, the TV will display the following respective screens.

CableCARD is installed

OR

CableCARD is not installed

After the CableCARD is installed, wait until the second screen below appears. The third screen below will appear if a channel is not authorized for viewing. Press the EXIT button to exit the second screen.

CABLE

Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; and 6,381,747 licensed for limited viewing uses only.

CableCARD(Top of card faces right)Top faces

Acquiring Data. Please wait.Upgrade Card

AIRMONITOR OUTS I V I D E O V I D E O A U D I O

Y/ VIDEO

Y/ VIDEO

Top

s face

th

ay is w

HDMI INPUT 1

l Cab

e

D CARHDMI INPUT 2

PB

PB

In order to start cable service for this device, please contact your cable provider CableCARD(tm): 123-456-789-1 Host: 123-456-789-1 Data: 123-456-789-1 Unit Address: 123-456-789-1

OPTICAL OUTPR PR

Digital Audio

(MONO)

(MONO)

(MONO)

(MONO)

L

TV AS CENTERR

CAUTION

AUDIO TO HI-FI

INPUT 1 INPUT 2 INPUT 3 INPUT 4Press EXIT to return

NOTE: 1. A digital cable subscription is required. 2. Do not insert a PCMCIA card into the CableCARD slot.

OR

Not an Authorized Channel

Please take note of all information on the screen (you will provide this information to your cable operator). Call your cable operator and give them the information from the card to start your cable service.

20

LC58/LC58E

GENERAL INFORMATION

Rear Panel ConnectionsTIPS ON REAR PANEL CONNECTIONS S-VIDEO, Y-PBPR and HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature. If your device has only one audio output (mono sound), connect it to the left audio jack on the television.AIROutside Antenna or Digital Cable

CABLE

Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; and 6,381,747 licensed for limited viewing uses only.

CableCARD(Top of card faces right)Top faces

External Digital Component with HDMI output capabilityHDMI OUT

Upgrade Card HDMI INPUT 1

Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT 1 in the example on this page). Refer to your VCR operating guide for more information on line input-output connections. You may use VIDEO or S-VIDEO inputs to connect to INPUT 1, INPUT 2 or INPUT 5, but only one of these may be used at a time. Connect only one component (VCR, DVD player, camcorder, etc.) to each input jack.

Y/ VIDEO

Y/ VIDEO

MONITOR OUTS I V I D E O V I D E O A U D I O

HDMI INPUT 2PB PB

OPTICAL OUTPR PR

Digital Audio

(MONO)

(MONO)

(MONO)

(MONO)

L

TV AS CENTERR

CAUTION

OPTICAL IN

AUDIO TO HI-FI

INPUT 1 INPUT 2 INPUT 3 INPUT 4

To an amplifier/ receiver with optical input capability.

INPUTS-VIDEO

OUTPUT

OUTPUT

OUTPUT

V

L

R

S-VIDEO

V

L

R

S-VIDEO

V

L

R

Y PB/CB PR/CR L

R

VCR #2

Laserdisc player, VCR, Camcorder, etc.

VCR #1

DVD Player

COMPONENT: Y-PBPR (INPUT 3 and INPUT 4) connections are provided for high performance components, such as DVD players and set-topboxes. Use these connections in place of the standard video connection if your device has this feature. INPUT 3 accepts both composite and component video signals. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TVs PB input and the components R-Y output to the TVs PR input. Your component outputs may be labeled Y-CBCR. In this case, connect the components CB output to the TVs PB input and the components CR output to the TVs PR input. You may use composite and component video signals for INPUT 3 and INPUT 4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs.

To ensure no copyright infringement, the MONITOR OUT output may be abnormal, when using the Y-PBPR jacks. When using an HDMI input from a Set-Top-Box, it is recommended that a 1080i or 720p input signal is used.

NOTE: 1. Connect only one component to each input jack. 2. Follow connections that pertain to your personal entertainment system. 3. INPUT 3 and INPUT 4 can accomodate Composite and Component video signals. 4. Cables are not included with the purchase of this TV, except when noted as provided. MACROVISION NOTES: 1. Video signals fed through a VCR may be affected by copyright protection systems and the picture will be distorted on the television. 2. Connecting the television directly to the Audio /Video output of a Set-Top-Box will assure a more normal picture.

21

LC58/LC58E

GENERAL INFORMATION

Lamp ReplacementLamp Life The lamp life may vary based on usage of the LCD Rear PTV. Turning on and off frequently may shorten the life of the lamp. Lamp Replacement After extended use, if the TV picture turns dark, the color looks unusual or LAMP INDICATOR light turns on, then it is time to replace the lamp with a new lamp.

WARNING:The lamp gets very hot! The lamp may explode if improperly handled. To avoid injury, please observe the following precautions. Do not open lamp compartment or attempt to remove lamp assembly unless the lamp assembly is being replaced. Unplug the products power cord from the AC outlet before attempting to replace the lamp assembly. If the lamp is in use when failure occurs or if the lamp has exploded, wait at least 30-45 minutes for the lamp to cool before opening the lamp compartment or touching the lamp assembly or any broken pieces. Broken lamp pieces can cause injury. Handle with gloves to avoid cuts. Do not place any foreign objects inside the lamp compartment. When installing a new lamp, follow handling instruction included with the new lamp. Do not touch glass surface of new lamp. This product contains lead and a lamp that contains mercury. Dispose of this product and its lamp in accordance with applicable environmental laws. For lamp recycling and disposal information, go to www.lamprecycle.org. For product recycling and disposal information, contact your local government agency or eRecycle.org (in California), the Electronic Industries Alliance at www.eiae.org (in the US) or the Electronic Product Stewardship Canada at www.epsc.ca (in Canada). For more information, call 1-800-HITACHI.

CAUTION!

A LAMP indicator will light when lamp becomes hot. Unplug products power cord from the AC outlet and allow lamp to cool for at least 30-45 minutes. If LAMP indicator is still lit, please contact your authorized service center .

NOTES: Contact your Hitachi dealer for a new lamp unit. Using other lamps may cause damage to the TV Set. MODEL#50VF820/VG825 55VF820/VG825 60VF820/VG825

LAMP TYPELP700 LP700 LP700

PART#UX21516 UX21516 UX21516

When replacing the lamp, let it cool down completely, for approximately 30 to 45 minutes after the power has been switched off and A.C. cord has been unplugged. Do not touch the glass of the new lamp or make it dirty which can shorten the life of the lamp and reduce the picture quality. Keep the lamp out of the reach of children and away from flammable materials. Do not pour water onto the removed lamp or put any object inside the lamp. Once the lamp is removed, do not put flammable materials and metal objects inside the lamp receptacle on the TV set. Do not touch the receptacle. Install the new lamp securely, otherwise the picture may become dark or it may cause severe overheating. Install the lamp cover correctly, otherwise power will not come on.

22

LC58/LC58E

GENERAL INFORMATION

Lamp ReplacementLamp Replacement 1. Turn off the main power switch and unplug the power cord.

120V

Lamp Temp Power

CAUTION: The lamp is very hot and may cause fire or severe burns. Wait at least 30~45 minutes to allow the lamp to cool before proceeding with lamp removal.

2.

Locate the Lamp Compartment on the left side of the LCD TV.

Lamp Compartment

23

LC58/LC58E

GENERAL INFORMATION

Lamp Replacement3. Remove the screw securing the lamp cover with a Phillips head screw driver as shown. Remove the lamp cover.

SCREW

PHILLIPS HEAD SCREW DRIVER

LAMP COVER

CAUTION: The lamp is very hot and may cause fire or severe burns. Wait at least 30~45 minutes to allow the lamp to cool before proceeding with lamp removal.

4.

Remove the two screws that hold the lamp in place. Remove the lamp unit by holding the lamp handle, then pulling outwards. Exercise caution when removing the lamp unit to avoid injury to your fingers.

NOTE: Do not put your hand in the Lamp Storage area after the Lamp Unit is removed, your may get burned.

HANDLE

5.

Replace with the new lamp. Place the removed lamp into the empty box of the replacement lamp. Do not touch the front glass of the new lamp or its receptacle. This may shorten the life of the lamp and reduce the picture quality. Push the lamp unit back to its original position. Tighten the screws firmly on the lamp unit. If they are loose, the TV may not operate correctly.

HANDLE

TIGHTEN THE SCREWS

24

LC58/LC58E

GENERAL INFORMATION

Lamp Replacement6. Without installing the lamp cover, the power will be off and the Lamp Indicator will flash (see page 16). Be sure to install the lamp cover by re-engaging the two clips and tighten the screws before turning the power on, otherwise it may cause unusual colors.

LAMP COMPARTMENT

PHILLIPS HEAD SCREW DRIVER

NOTE: If power is connected before the Lamp Cover is installed, the power will be off and the Lamp Indicator will flash (see page 16).

7.

Plug power cord into AC outlet and turn on the main power switch.

120V

Lamp Temp Power

NOTE: This product contains lead and a lamp that contains mercury. Dispose of this product and its lamp in accordance with applicable environmental laws. For lamp recycling and disposal information, go to www.lamprecycle.org. For product recycling and disposal information, contact your local government agency or eRecycle.org (in California), the Electronic Industries Alliance at www.eiae.org (in the US) or Electronic Product Stewardship Canada atwww.epsc.ca (in Canada). For more information, call 1-800-Hitachi.

25

LC58/LC58E

Quick Reference Remote Control Buttons and FunctionsIn addition to controlling all of the functions on your HITACHI LCD Rear Projection TV, the new remote control is designed to operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite receivers, and VCRs. The remote control must be programmed to control the chosen device. Please see I/B manual for a complete description of all features and programming of the Remote Control.

POWER BUTTON (TV, DVD, CBL, STB, PVR/VCR, AMP/CD) Turns the selected device on and off. MODE INDICATOR Turns on or blinks to show remote control mode when the SOURCE ACCESS buttons are pressed. SOURCE ACCESS BUTTONS (TV, DVD, CBL, STB, PVR/VCR, AMP/CD) Changes the mode of the Universal Remote Control to control the device selected. ASPECT BUTTON (TV) Changes the aspect ratio of the TV. DAY/NIGHT (TV) Toggles picture mode settings between DAY and NIGHT mode. MENU BUTTON (TV, DVD, CBL, STB, PVR/VCR) Accesses the OSD menu system. CURSOR PAD/SELECT BUTTON (TV, DVD, CBL, STB, PVR/VCR) The Cursor Pad is used as a cursor to navigate through the OSD and INPUT menu systems. The Select button is used to Select/Activate highlighted menu items.

DVD/VCR CONTROL BUTTONS (DVD, PVR/VCR, AMP/CD) Controls the functions of your VCR, DVD and audio devices. PAUSE BUTTON (TV,PVR/VCR, DVD, AMP/CD) Press to show and change the Freeze mode of the TV. Also used to pause other devices when the remote is in DVD, PVR/VCR, or AMP/CD mode. PIP CONTROL BUTTONS (TV) Press to show and change the Picture-in-Picture mode.

GUIDE BUTTON (TV, STB, CBL, PVR) Accesses the TV Guide On ScreenTM system (see page 55) of the TV or the program guide of other devices. EXIT BUTTON (TV, CBL, STB, PVR/VCR) Exits out of the OSD, INPUTS or AV NET menu systems if their menu is displayed. LAST CHANNEL BUTTON (TV, CBL, STB, PVR) Switches between the current and last channel viewed. INPUTS BUTTON (TV, AMP) Accesses the INPUTS menu system./

INFO BUTTON (TV, STB, CBL, PVR) Displays various information on the screen, such as channel information. VOLUME WHEEL (TV, AMP/CD) Scroll up and down to adjust the audio level of your TV. Push down on the wheel to mute. NUMERIC BUTTONS (TV, DVD, CBL, STB, PVR/VCR, AMP/CD) Used to manually enter the TV channel, and used for numeric entry when navigating through the OSD, INPUTS, and AV NET menu systems.

CHANNEL WHEEL (TV, CBL, STB, PVR/VCR, AMP/CD) Scroll up or down to change channel. Push down on the wheel to access (FAV) Favorite Channel mode. (Favorite channel is only available for TV mode.)

(-) BUTTON (TV,STB) The (-) button is used when the remote is in Set-Top-Box (STB) mode or when the TV uses a digital input.

LIGHT BUTTON (TV, CBL, STB, PVR) Press to use the back light feature. Can also be used to change backlight mode.

CLU-3851WLLEGEND TV Television CBL Cable Box STB Set-Top-Box VCR Video Cassette Recorder/Player DVD Digital Video Disc Player SAT Satellite Receiver

NOTES:

1. The TVs remote control sensor is located on the right bottom portion of the TV screen. To control TV functions, please point the remote control directly at the remote control sensor for best results. 2. VCR precode is included in the PVR mode. 3. CD precode is included in the AMP mode. 4. Pressing any button will illuminate the backlight for 4 seconds.

TABLE OF CONTENTS

26

LC58/LC58E

Quick Reference Remote Control Buttons and FunctionsIn addition to controlling all of the functions on your HITACHI LCD Rear Projection TV, the new remote control is designed to operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite receivers, and VCRs. The remote control must be programmed to control the chosen device. Please see manual for a complete description of all features and programming of the Remote Control.POWER BUTTON (TV, CBL, VCR, DVD, SAT) Turns the selected device on and off. INPUTS BUTTON (TV) Accesses the INPUTS menu system. ASPECT BUTTON (TV) Changes the aspect ratio while watching TV. MENU BUTTON (CBL, DVD, SAT, TV) Accesses the OSD menu system. CURSOR/SELECT BUTTONS (TV, DVD, CBL, SAT) The CURSOR buttons are used to navigate the cursor through the OSD and INPUTS menu systems, and the SELECT button is used to Select/Activate the highlighted menu item. VOLUME BUTTONS (TV) Adjusts the audio level of your TV. MUTE BUTTON (TV) Reduces the audio level to 50% if pressed once, and to complete mute if pressed twice. Press it a third time to restore audio level. NUMERIC BUTTONS (TV, DVD, CBL, SAT, VCR) Used to manually enter the TV channel, and used for numeric entry when navigating through the OSD menu system. (-) BUTTON (TV, SAT) The (-) button is used when the remote is in Set-Top-Box (STB) mode or when the TV uses a digital input. RECORD BUTTON (VCR) Press twice (2 times) to record programs. SOURCE ACCESS BUTTONS (TV, DVD, VCR, CBL, SAT) Changes the mode of the Universal Remote Control to control the device selected. DAY/NIGHT BUTTON (TV) Select picture mode settings between DAY and NIGHT mode. PIP BUTTON (TV) Press to show and change the Picture-in-Picture mode. EXIT BUTTON (TV, CBL, SAT) Exits out of the OSD or INPUTS menu systems if their menu is displayed. FAVORITE CHANNEL (FAV CH) button (TV) Press to enter/access Favorite Channel (FAV) mode. GUIDE BUTTON (SAT/STB, CBL,TV) Accesses the channel guide of the TV or program guide of other devices. INFO BUTTON (TV, CBL, SAT) Displays various information on the screen. CHANNEL BUTTONS (TV, CBL, SAT, VCR) Changes the channel. LAST CHANNEL (LC) BUTTON (TV, CBL, SAT) Switches between the current and last channel viewed. DVD/VCR CONTROL BUTTONS (DVD, VCR) Controls the precode functions of your VCR and DVD. PAUSE BUTTON (TV, VCR, DVD) Press to show and change the Freeze mode of the TV or pause other devices.

CLU-4352UG2LEGEND TV Television CBL Cable Box STB Set-Top-Box VCR Video Cassette Recorder/Player DVD Digital Video Disc Player SAT Satellite Receiver NOTE: STB precode is included in the SAT mode.

27

LC58/LC58E

DISPLAY PICTURE FORMAT ASPECT button

Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal format received, the picture format ratio allows you to adjust the images through the following options.

4:3 STANDARD

Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the left and right of the image to preserve the original aspect ratio of the source. Note: Use this mode for only 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted area of the picture will age more rapidly than the gray areas.

4:3 ZOOM1/ZOOM2 16:9 STANDARD

Use these aspect modes to zoom in on conventional (4:3) sources. Use this aspect mode to display 16:9 sources like HDTV and DVDs preserving the original 16:9 aspect ratio.

4:3 EXPANDED

16:9 ZOOM

Use this aspect mode to display conventional (4:3) sources by linearly increasing image expansion from the center towards the edges of the display area in order to fill it.

Use this aspect to Zoom-in once while in 16:9 aspect.

Antenna-Analog S-Video/Video Input (Auto Aspect: Off) HDMI-480i/480p Input (Auto Aspect: Off) Component-480i/480p Input (Auto Aspect: Off)

Antenna-Digital (4:3) S-Video/Video 4:3 Letter Input (Auto Aspect: On) HDMI-480i/480p 4:3/ Letter Input (Auto Aspect: On) Component-480i/480p 4:3 Letter Input (Auto Aspect: On) S-Video/Video 16:9 Input (Auto Aspect: On) HDMI-480i/480p 16:9 Input (Auto Aspect: On) Component-480i/480p 16:9 Input (Auto Aspect: On) Antenna-Digital (16:9) HDMI-720p/1080i Input Component-720p/1080i InputNOTE:

1. The Aspect Style setting you select for an ANT input will automatically be set for the other ANT input. However, all five video inputs have independent Aspect Style settings. 2. Vertical position adjustments are directly available when you choose 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM aspect style.28

LC58/LC58E

Picture-in-Picture (PIP)PIP Mode Picture-in-Picture

This feature is only available with a Digital 16:9, 720p and 1080i signal. To prevent a pattern burn, occasionally move the sub-picture using the CURSOR buttons.

Picture-in-Picture (PIP) Modes PIP Main/ Mode Sub Digital Tuner Aspect 16:9 4:3 1080i/ 720p 16:9

POP

PIP

ANT Digital 480p/480i ANT Analog S-Video/Video PIP ANT Digital 4:3 1080i/720p 480p/480i S-Video/Video PIP ANT Digital 16:9 1080i/720p 480p/480i S-Video/Video SPLIT ANT Digital

16:9 16:9 4:3

Yes1 Yes Yes Yes2 Yes Yes Yes

Yes1 Yes

Yes Yes

480p/480i Analog Tuner Video/S-Video 16:9 4:3

Yes

Yes

16:9 16:9 16:9 16:9 16:9 16:9 16:9 4:3 16:9 16:9 4:3

Yes Yes2 Yes Yes Yes

Yes1 Yes2 Yes Yes

Yes Yes Yes Yes

MAIN PICTURESUB PICTURE

1080i/720p 480p/480i ANT Analog S-Video/Video SURF Yes Yes 12 PIX Yes1 = Auto Aspect Off; Yes2 = Auto Aspect On PAUSE button

Yes Yes

SPLIT Mode Picture-in-Picture

Split Mode PIP displays the main picture and subpicture evenly on the screen.MAIN PICTURE SUB PICTURE

If you wish to freeze the sub-picture, press the PAUSE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the EXIT button. Press the PAUSE button repeatedly to toggle between FREEZE modes (Main Freeze, SPLIT and STROBE).

Freeze

Surf Mode PIP automatically scans all active channels (those set in memory) and displays them as PIP sub-pictures or Thumbnail channels. Press the SELECT button to stop on a chosen channel. Use the remote CURSOR buttons ( , , , ) to navigate the Thumbnail. Press the EXIT button to enable your chosen channel and return to normal viewing.1 5 9 13 2 6 10 14 3 7 11 15 4 8 12

SURF Mode Picture-in-Picture

Freeze

Freeze16

FreezeNOTE:

Press the SELECT button to stop the Surf mode or channel scan. Press the SELECT button again to resume Surf mode or channel scan.

FreezeEXIT

29

LC58/LC58E

Picture-in-Picture (PIP)MAIN FREEZE

Press the PAUSE button to freeze one frame of the picture you are currently viewing and the frozen frame will show in the Main Picture. Press the EXIT button to return to normal viewing. This feature is useful for freezing a picture frame with addresses.

STROBE FREEZE

Press the PAUSE button to freeze three frames of the picture you are currently viewing (only the 3 sub-pictures will freeze). Press the EXIT button to return to normal viewing. This feature is useful for viewing a moving picture that has many details, for example, a close play in a sporting event or a golf swing.

EXIT

EXIT

Press the PAUSE button to freeze the picture you are currently viewing (only the right sub-picture will freeze). Press the EXIT button to return to normal viewing.MAIN PICTURE SUB PICTURE

SPLIT FREEZE

NOTE:

1. The default FREEZE mode is the MAIN freeze followed by the SPLIT freeze and then the STROBE freeze. The last Freeze mode you selected before you pressed the EXIT button will be the one that comes up after pressing the PAUSE button again. 2. Each freeze frame is delayed about 0.1 (1/10) second.

EXIT

30

LC58/LC58E

SERVICE ADJUSTMENTSTO GO TO AN ADJUSTMENT, CLICK ON ITS HEADING BELOW

1. CHASSIS ADJUSTMENT................................................................................................................................... 32 1-1. Service Menu Access .................................................................................................................................................32 1-2. Memory Initialize ....................................................................................................................................32 1-3. Factory Reset ...........................................................................................................................................33 1-4. Factory and Service Adjustments ...........................................................................................................33 2. FINAL ASSEMBLY ADJUSTMENT (Adjustment order) ..................................................................................33 2-1. Preheat run conditions ............................................................................................................................33 2-2. Subcontrast Adjustment .........................................................................................................................33 2-3. Raster Position Adjustment ....................................................................................................................34 2-4. Flicker Adjustment ..................................................................................................................................34 2-5. Ghost Adjustment ...................................................................................................................................34 2-6. NRSH Adjustment ..................................................................................................................................34 2-7. Display Area Specifications ....................................................................................................................35 2-8. Gamma Correction (White Balance) ....................................................................................................36 2-9. Color Uniformity (White Uniformity) ....................................................................................................37 2-10. Drive Adjustment Check .......................................................................................................................38 2-10-1. Dot Stripe Checking ...................................................................................................................38 2-10-2. Sub Ghost Checking ..................................................................................................................38 2-10-3. Horizontal Crosstalk Checking ...................................................................................................38 2-11. Lamp Door Protection Operation Check ...............................................................................................39 2-12. Lamp Holder Protection Operation Check ...........................................................................................39 2-13. High Temperature Protection Operation Check ....................................................................................39 2-14. Temperature Sensor Data Setting .......................................................................................................40 2-15. Checking of Temperature Sensor .........................................................................................................41 2-16. Adjustment I2C Parameter List ..............................................................................................................42 2-17. Adjustment OSD Flow Chart ..................................................................................................................79 2-18. Troubleshooting Flow Charts .............................................................................................................................88

*IMPORTANT For many of the above adjustments, it is necessary to have an HDTV (1080i or 720P) signal generator, SDTV (480P) signal generator, as well as the usual NTSC (480i) signal generator. Hitachi recognizes that few companies offer HDTV or SDTV signal generators and that the cost of these generators is sometimes prohibitive. For this reason, we suggest the use of a set-top-box for HDTV and SDTV adjustments. Usually, there is a switch on the set-top-box which enables it to output HDTV (1080i or 720P) or SDTV (480P) signals even with no input. In this case, the sync is automatically detected by the TV (at the Y-PBPR Inputs on the rear panel). TABLE OF CONTENTS

31

LC58/LC58E ADJUSTMENT PROCEDURE START-UPThe 50,55 & 60 VF820/VG825 LCD rear proyection sets pass through adjustment procedures during the assembly process. These adjustments must be done to assure the best performance of the LCD set for the consumer. Also, after servicing, these same adjustments must be done. Most of the adjustments are made by the I2C bus by changing data in the Adjustment mode menu. On pages 42-78 shows the complete parameter list with a brief description, signal format, the adjustment range and the initial data.Remote Control ButtonsMENU EXIT EXIT

Change Selection (Up) Increase Data Value Change Selection (Down)

Increase Data Value

SELECT

1-1 HOW TO GET TO ADJUSTMENT MODE Chassis adjustment mode can be access by pressing the R/C keys MENU + MENU + 8 + SELECT to enter adjustment mode. For some parameters the only way to see them is by selecting the parameter number than pressed SELECT in order to see it; then DATA can be change if other parameter needs to change then press key then repeat the same procedure.

B. To make a selection, use the NUMBER pad on the PTV R/C ; example : select SEINE press 69 then SELECT the DATA shown is "EB" ; if this DATA needs to be change press the , , keys to modify, when finish press SELECT key to store the new DATA value. normal condition. C. After finishing the necessary adjustment press the R/C EXIT key or EXIT key on the side panel. Adjustment mode is released and PTV set returns to normal condition.

ADJUST MODE RGB H POSITION ** V POSITION ** ENBW ** GHOST VCOM NRSH STRIPE S.GHOST STREAKOther way to access this mode is by use JIG R/C code: (9C Hex). To escape from Adjustment Mode press NPUTkey on Side I panel or EXIT key of R/C to exit service adjustment mode.

1-2 MEMORY INITIALIZE 1-2.1 MEMORY INITIALIZE OPER TION A NOTE: The execution of this function returns the adjustment codes to the preset values, therefore, adjustment data will be lost.Procedure (1) Enter Adjustment mode by the method described in sub-items 1.1 and 1.2 from item 1 (Adjustment procedure start up). (2) Get to the second page of Adjust Mode by pressing remote control Menu key once, or with either the R/C or front panel , cursor keys several times. (3) Select MEMORY INIT adjust code. (4) Activate MEMORY INIT by pressing cursor key for more than 3 seconds. (5) Check the following process for initialization operation.

1-1.1 CHANGING DATA AND SELECTING ADJUSTMENT CODEWhen the PDP set is in adjustment mode, the cursor , , , and MENU keys of the remote control or front panel may be used as the adjustment keys. A. Use any Hitachi remote control when making an adjustment. , keys are used for selecting adjustment item.

A screen is be colored blue when MEMORY INITMENU EXIT EXIT

Process of Memory Initialize operation. start.

A screen is be colored green when MEMORY INIT A screen is be colored black when MEMORY INITfinish abnormally. (6) Do not unplug from AC outlet until this operation is complete and do not perform any key operation either, after this operation each factory setting and all adjust mode data should reset to delivery settings automatically. (7) After Memory Initialize, it should be unplug AC cord. Unplug and plug AC cord and then all settings and data are updated. (8) When PTV turns ON , it will tune CH03 this is the complete operation of Memory Initialize process. finish normally.

SELECT

, keys are used for changing data values. MENU key is used to advance through the adjustment mode menus and pages.

BACK TO ADJUSTMENTS

32

LC58/LC58E 1-3 FACTORY RESET OPERA TION

NOTE: The execution of this function returns the adjustment made by the customer , this will return all the adjustments to the original shipping conditions. Procedure (1) Enter Adjustment mode by the method described in sub-items 1.1 and 1.2 from item 1 (Adjustment procedure start up). (2) Get to the second page of Adjust Mode by pressing remote control Menu key once, or with either the R/C or front panel , cursor keys several times. (3) Select FACTORY RESET adjust code. (4) Activate FACTORY RESET by pressing cursor key for more than 3 seconds. (5) Check the following process for FACTORY RESET operation. Process of FACTORY RESET operation. A screen is be colored MAGENTA when FACTORY RESET start. A screen is be colored green when FACTORY RESET finish normally. A screen is be colored black when FACTORY RESET finish abnormally. (6) Do not unplug from AC outlet until this operation is complete and do not perform any key operation either, after this operation each factory setting and all adjust mode data should reset to delivery settings automatically. (7) After FACTORY RESET, it should be unplug AC cord. Unplug and plug AC cord and then all settings and data are updated. (8) When PTV turns ON , it will tune CH03 this is the complete operation of FACTORY RESET process.

II Final ASSEMBLY ADJUSTMENT2 - 1 PRE HEAT RUN CONDITION Heat run should be performed with moving picture or no signal. And disable side panel or top/bottom panel. Do NOT use stock market quotation, computer graphics, and other fixed (non-moving) image.Table 2.1 Final adjustment orderOrder 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Adjustment Item SUB CONTRAST ADJUSTMENT (RGB) RASTER POSITION ADJUSTMENT GHOST ADJUSTMENT FLICKER ADJUSTMENT NRSH ADJUSTMENT White Balance (GAMMA) ADJUSTMENT WHITE UNIFORMITY ADJUSTMENT DOT STRIPE CHECKING and ADJUSTMENT SUB GHOST CHECKING and ADJUSTMENT HORIZONTAL CROSS TALK CHECKING and ADJUSTMENT LAMP DOOR PROTECTION OPERATION CHECK LAMP HOLDER PROTECTION OPERATION CHECK HIGH TEMPERATURE PROTECTION OPERATION CHECK TEMPERATURE SENSOR OPERATION CHECK HDMI ADJUSTMENT / EDID DATA INSTALLATION Signal White Raster 480i,720P Circle pattern signal.

1-4 FACTORY AND SERVICE ADJUSTMENTS The adjustment item that is affected by the memory initialize operation is shown below:* JIG. R/C FACTORY PRESET CODE:92 MEMORY INITIALIZE and FACTORY PRESETITEM MEMORY INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE Set to No for heat-run FACTORY RESET REMARKS

2-2 SUB-CONTRASTADJUSTMENT Preparation Receive Sub-contrast adjustment signal (Fig. 1).Adjustment (1) Select SUB CONTRAST of Service Adj. Menu. Press for over 2 seconds and have it perform automatic adjustment. When its completed, Auto Adjusting on the screen will be disappeared. Fig. 1 Full WhiteV1 V2

H POSITION ADJUST DATA V POSITION ADJUST DATA RGB(480p) ADJUST DATA SETTING DATA FOR EACH DEVICE BBE EFFECT SETTING DATA AUDIO AGC SETTING DATA V CHIP RATING SETTING DATA CCD SETTING DATA FACTORY RESET ITEM LAMP TIME Accumulate TIME GHOST ADJUST DATA FLICKER ADJUST DATA(V.COM) NRSH ADJUST DATA COLOR UNIFORMITY GAMMA CORRECTION V.REF (EPSON PANEL ONLY ) Automatic Power saving- Yes/No

NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE INITIALIZE INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE NOT INITIALIZE Set to Yes

V3

(RF Input ANT A)) V1=1.0 Vp-p (when V2=100IRE with V3=7.51IRE) (Y PBPR Input 720p,1080i) V1=1.0 Vp-p (when V2=100IRE with V3=7.51IRE)

NOTE: (1) If there is a different value than shown in I2C Parameter List, for

fixed data, adjust it using

,

buttons (only in this case)

BACK TO ADJUSTMENTS

33

LC58/LC58E

Final ASSEMBLY ADJUSTMENT2-3 RASTER POSITION ADJUSTMENT(1) Receive Circle pattern signal. (2) Recall Adjustment menu. (3) Select V POSITION by using the cursor stick ( / direction) on handset. Adjust the horizontal picture position where |E-F| No.12 LCD ADJUST GAM No.12 R 126->increase this data G 138 B 105

Remark: The gamma data for higher intensity should always be bigger than that of lower intensity. If not, noise may appear on the screen. example: GAM No11 GAM No12 R 120 > 119 R 120 < 128 R 120 < 125

< > G/C WRITE_press for several second After this procedure, this new data will be write back to E2PROM. It takes about 20 second