FIRE ALARM

4100ESFire Alarm System

InstallationGuide

574-848Rev. BD

i

Cautions, Warnings, and Regulatory Information

Copyright and Trademarks

© 2017 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and are subject to change without notice. Additional listings may be applicable, contact your local Simplex® product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. Simplex, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited. NFPA 72 and National Fire Alarm Code are registered trademarks of the National Fire Protection Association (NFPA).

Microsoft and Windows are registered trademarks of Microsoft Corporation. VESDA is a trademark of Xtralis Pty Ltd. NFPA 72 and National Fire Alarm and Signaling Code are registered trademarks of the National Fire Protection Association (NFPA).

Cautions and

Warnings

READ AND SAVE THESE INSTRUCTIONS - Follow the instructions in this installation manual. These instructions must be followed to avoid damage to this product and associated equipment. Product operation and reliability depend upon proper installation.

DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED- Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex product supplier.

ELECTRICAL HAZARD - Disconnect electrical field power when making any internal adjustments or repairs. All repairs should be performed by a representative or authorized agent of your local Simplex product supplier.

STATIC HAZARD - Static electricity can damage components. Handle as follows:• Ground yourself before opening or installing components.• Prior to installation, keep components wrapped in anti-static material at all times.

EYE SAFETY HAZARD - Under certain fiber optic application conditions, the optical output of this device may exceed eye safety limits. Do not use magnification (such as a microscope or other focusing equipment) when viewing the output of this device.

SULFURIC ACID WARNING- Battery contains sulfuric acid, which can cause severe burns to the skin and eyes and can destroy fabric. Replace any leaking or damaged battery while wearing appropriate protective gear. If you come in contact with sulfuric acid, immediately flush skin or eyes with water for 15 minutes and seek immediate medical attention.

FCC RULES AND REGULATIONS - PART 15 - This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT: Verify FACP System Programmer, Executive, and Slave Software compatibility when installing, or replacing system components. Refer to the Technical Support Information and Downloads website for compatibility information.

ii

Emissions Compliance, Radio Frequency Immunity, Safety and Agency Approvals

EMC Emissions

• FCC 47 CFR Part 15 Class A Emission Requirements (USA)

EMC Immunity

• EN50130-4: 1996, Electromagnetic compatibility- Product family standard: Immunity requirements for components of fire, intruder, and social alarm systems.

System Type:Fire Alarm Control Panels

4100-9111, 4100-9112, 4100-9113, 4100-9121, 4100-9131, 4100-4100-9132, 4100-9133, 4100-9211, 4100-9230, 4100-9311, 4100-9314, 400-9331, 4100-9312, 4100-9313, 4100-9315, 4100-9316, 4100-9332, 4100-9511, 4100-9512, 4100-9513, 4100-9531, 4100-9532, 4100-9533, 4100-9534.

Transponders and Remote Annunciators4100-9600, 4100-9601, 4100-9610

Analog and Digital Audio Options4100-9620, 4100-9621

Network Display Units4100-9141, 4100-9142, 4100-9143, 4100-9144, 4100-9145, 4100-9146, 4100-9241, 4100-9242, 4100-9342, 4100-9352, 4100-9355, 4100-9542.

Manufacturer’s Name: Simplex Time Recorder Co., D/B/A TEPG-US

Manufacturer’s Address: 50 Technology DriveWestiminster MA 01441-0001United States of America.

iii

Listings, Approvals, Codes, and Standards

Listings and Approvals

This equipment meets the requirements of the following agencies.• UL (UL 864)• ULC (S527)• FM (Class No. 3010)• CSFM• MEA

Codes and Standards

If the notification appliances and accessories referenced in Table I are installed in accordance with either NFPA 12A or NFPA 2001, the system must employ an additional mechanically-operated manual release mechanism.

The installer should be familiar with the relevant codes listed below, as well as any other applicable local codes and standards, when installing a fire alarm system.

NFPA 72 National Fire Alarm and Signaling CodeNFPA 11 Standard for Low-Expansion Foam and Combined Agent SystemsNFPA 11A Standard for Medium- and High-Expansion Foam SystemsNFPA 12 Standard for Carbon Dioxide Extinguishing SystemsNFPA 12A Standard on Halon 1301 Fire Extinguishing SystemsNFPA 13 Standard for Installation of Sprinkler SystemsNFPA 14 Standard for the Installation of Standpipe and Hose SystemsNFPA 15 Standard for Water Spray Fixed Systems for Fire ProtectionNFPA 16 Standard for the Installation of Deluge Foam-Water Sprinkler and Foam-

Water Spray SystemsNFPA 16A Standard for the Installation of Closed-Head Foam-Water Sprinkler SystemsNFPA 17 Standard for Dry Chemical Extinguishing SystemsNFPA 17A Standard for Wet Chemical Extinguishing SystemsNFPA 25 Standard for Inspection, Testing, and Maintenance of Water-Based Fire

Protection SystemsNFPA 70 National Electric CodeNFPA 72 National Fire Alarm and Signaling CodeNFPA 101 Life Safety CodeNFPA 750 Standard on Water Mist Fire Protection SystemsNFPA 2001 Standard on Clean Agent Fire Protection SystemsULC S524 Standard for Installation of Fire Alarm Systems (Canadian Systems)UL 1076 Standard for Safety for Proprietary Burglar Alarm Units and Systems

Environmental Operating Range

The 4100ES and all modules are rated to operate at ambient temperatures from 32oF - 120oF

(0oC - 49oC).

The 4100ES and all modules are rated for operation at 90oF (32oC), 93% RH (non-condensing).

7

Table of Contents

Cautions, Warnings, and Regulatory Information ..................................................... iCopyright and Trademarks ....................................................................................... iEmissions Compliance, Radio Frequency Immunity, Safety and Agency Approvals iiListings, Approvals, Codes, and Standards............................................................. iiiListings and Approvals .............................................................................................iiiCodes and Standards ..............................................................................................iiiEnvironmental Operating Range .............................................................................iiiList of Figures ......................................................................................................... xvList of Tables ....................................................................................................... xviii

Chapter 1 Introduction to the 4100ES Fire Alarm System ............................. 1-1Introduction ..........................................................................................................................1-1

In this chapter ......................................................................................................................1-1

System Configurations ................................................................................................... 1-2 Overview .............................................................................................................................1-2

Standalone Configuration ............................................................................................... 1-3Overview ..............................................................................................................................1-3System Design .....................................................................................................................1-3

MINIPLEX Configuration ................................................................................................. 1-4Overview ..............................................................................................................................1-4System Design .....................................................................................................................1-4

RUI Communication .............................................................................................................1-5

Network Configuration .................................................................................................... 1-6Overview ..............................................................................................................................1-6

Hub and Star Configurations ................................................................................................1-6

Connection Loops ................................................................................................................1-7System Design .....................................................................................................................1-7

Network Communication ......................................................................................................1-7

4100ES Back Box PIDs ................................................................................................... 1-8Overview ..............................................................................................................................1-8

4100ES Back Boxes ............................................................................................................1-8

4100ES PIDs ..................................................................................................................... 1-9Overview ..............................................................................................................................1-9

Basic Control Panels (United States) ...................................................................................1-9

Basic Control Panels (Canada) ..........................................................................................1-10

Basic Control Panels (International) ..................................................................................1-12Transponders .....................................................................................................................1-13

Remote Annunciator ..........................................................................................................1-13

Remote Display Assemblies ..............................................................................................1-14Basic Audio Selections ......................................................................................................1-14

Utility Cabinets ...................................................................................................................1-14

Master Controller Upgrade Kits ..........................................................................................1-14Rack Mount Kits .................................................................................................................1-15

Power Distribution Modules ...............................................................................................1-15

Expansion Bays .................................................................................................................1-15Expansion Battery Chargers for Basic FACPs ...................................................................1-15

Communication Modules ...................................................................................................1-15

Power Supplies ..................................................................................................................1-16Signaling Modules ..............................................................................................................1-16

Annunciator Modules .........................................................................................................1-17

8

Table of Contents

Transponders and Transponder Components ...................................................................1-17

Audio Operator Interfaces ..................................................................................................1-17Audio Controller Boards .....................................................................................................1-17

Telephones/Microphones ...................................................................................................1-18

Additional Audio Modules ..................................................................................................1-18Common Audio Options .....................................................................................................1-18

Amplifiers ...........................................................................................................................1-18

Miscellaneous Modules ......................................................................................................1-20

4100 PIDs (Non-4100ES/4100U) .................................................................................... 1-21Overview ............................................................................................................................1-21

System Types and Options ................................................................................................1-21Master Controller Option Module .......................................................................................1-21

NAC Modules .....................................................................................................................1-22

IDC Modules ......................................................................................................................1-22Optional Modules ...............................................................................................................1-22

Auxiliary Relay Controls .....................................................................................................1-22

Audio Controllers and Amplifiers ........................................................................................1-23Audio Options ....................................................................................................................1-23

Annunciation Modules ........................................................................................................1-23

Miscellaneous Modules ......................................................................................................1-24Network Modules ...............................................................................................................1-24

System Accessories ...........................................................................................................1-24

Chapter 2 Installing FACP Components ......................................................... 2-1Introduction ..........................................................................................................................2-1In this chapter ......................................................................................................................2-1

Introduction to the FACP ................................................................................................2-2Overview ..............................................................................................................................2-2CPU Bay ..............................................................................................................................2-2

SPS CPU Bay Overview .................................................................................................. 2-3SPS CPU Master Motherboard ............................................................................................2-3Master Controller Daughter Card (566-719) ........................................................................2-4

Master Controller Daughter Card LEDs ...............................................................................2-5

Master Controller Switches ..................................................................................................2-5

System Power Supply (SPS) ...............................................................................................2-6

EPS CPU Bay Overview .................................................................................................. 2-7The Power Distribution Interface ..........................................................................................2-7

EPS CPU RUI+ Master Motherboard ..................................................................................2-7Master Controller Daughter Card (566-719) ........................................................................2-8

Master Controller Daughter Card LEDs ...............................................................................2-9

Master Controller Daughter Card Switches .........................................................................2-9Extended Power Supply with IDNet 2 ...............................................................................2-10

FACP Operator Interface ............................................................................................... 2-12Operator Interface ..............................................................................................................2-12

FACP Expansion Bays .................................................................................................. 2-13Additional CPU Bay Modules .............................................................................................2-13

Expansion Bays .................................................................................................................2-13

FACP Power Requirements .......................................................................................... 2-14System Power ....................................................................................................................2-14

9

Table of Contents

Power Requirements .........................................................................................................2-14

Overview ............................................................................................................................2-15Specifications .....................................................................................................................2-15

Mounting the Back Boxes ..................................................................................................2-16

Step 2. Mounting the System Electronics ................................................................... 2-18Overview ............................................................................................................................2-18

Mounting the System Electronics Bays ..............................................................................2-18

Step 3. Trim Kit Application (optional) ........................................................................ 2-21Trim Application .................................................................................................................2-21

Step 4. Mounting the Door ............................................................................................ 2-22Overview ............................................................................................................................2-22Attaching Doors ................................................................................................................2-23

Reversing the Door ...........................................................................................................2-24

Step 5. Installing Motherboards into the CPU Bay ..................................................... 2-25Overview ............................................................................................................................2-25

4100ES CPU Bay Placement Guidelines ..........................................................................2-25

Step 6. Installing Modules into Expansion Bays ........................................................ 2-26Overview ............................................................................................................................2-26

4100ES Placement Guidelines ..........................................................................................2-26

Motherboard Placement Guidelines for a 4100ES bay ......................................................2-27Mixed 4100 Motherboard/4100ES 4”x5” Card Placement Guidelines ...............................2-28

Installing 4 X 5 Cards .........................................................................................................2-29

Installing Motherboards into a 4100ES Expansion Bay .....................................................2-30

Step 7. Interconnecting Modules and Bays ................................................................ 2-31Overview ............................................................................................................................2-31

Guidelines ..........................................................................................................................2-31Power Distribution Module Connections ............................................................................2-31

SPS CPU Card Interconnections in the CPU Bay .............................................................2-34

SPS CPU Card Interconnections in Expansion Bays ........................................................2-34SPS CPU Basic Bay-To-Bay Interconnections ................................................................2-34

EPS CPU Bay Interconnections .........................................................................................2-36

EPS CPU Interconnections in Expansion Bays .................................................................2-36EPS CPU Basic Bay-To-Bay Interconnections ..................................................................2-36

Connecting to 4100 Motherboards .....................................................................................2-37

Step 8. Configuring Cards ............................................................................................ 2-39Overview ............................................................................................................................2-39Master Motherboard Configuration ....................................................................................2-39

Master Controller Daughter Card Configuration ................................................................2-39

SPS Configuration .............................................................................................................2-40EPS Configuration .............................................................................................................2-40

PDI Configuration ...............................................................................................................2-40

Configuring Other Cards ....................................................................................................2-40

Step 9. Installing and Removing Batteries .................................................................. 2-41Installing and Removing Batteries in a One Bay Cabinet ..................................................2-41

Installing and Removing Batteries in a Multi-Bay Cabinet .................................................2-42

Step 10. System Power Up and Power Down Procedures ......................................... 2-43System Power Up Procedure .............................................................................................2-43

System Power Down Procedure ........................................................................................2-43

The Terminal Block Utility Module ............................................................................... 2-44

10

Table of Contents

Overview ............................................................................................................................2-44

Mounting to the Electronics Bay ........................................................................................2-44

Chapter 3 Installing 4100ES MINIPLEX Components .................................... 3-1Introduction ..........................................................................................................................3-1

In this chapter ......................................................................................................................3-1

Introduction to MINIPLEX Transponders ...................................................................... 3-2Overview ..............................................................................................................................3-2

Transponder Cabinets .........................................................................................................3-2

Transponder Interface Cards (TICs) and Audio Riser Modules ...........................................3-2Basic TICs ............................................................................................................................3-2

The Local Mode TIC ............................................................................................................3-3

TIC Audio Risers ..................................................................................................................3-3TIC Illustrations ....................................................................................................................3-4

Local Mode Specifications ...................................................................................................3-5

LEDs ....................................................................................................................................3-6Card Specifications ..............................................................................................................3-6

MINIPLEX System Guidelines ........................................................................................ 3-7Overview ..............................................................................................................................3-7Guidelines ............................................................................................................................3-7

Configuring Cards ........................................................................................................... 3-8Overview ..............................................................................................................................3-8TIC Configuration .................................................................................................................3-8

CPU Motherboard DIP Switch (SPS Configuration Only) ...................................................3-8

Configuring Other Cards ......................................................................................................3-8

TIC/Riser Mounting .......................................................................................................... 3-9Overview ..............................................................................................................................3-9

Mounting Instructions ...........................................................................................................3-9

TIC/Motherboard Interconnections .............................................................................. 3-10Interconnections .................................................................................................................3-10

RUI Wiring ...................................................................................................................... 3-11Overview ............................................................................................................................3-11

RUI/RUI+ Specifications ....................................................................................................3-11

Wiring Configurations .........................................................................................................3-11

MINIPLEX Audio Wiring ................................................................................................ 3-12Overview ............................................................................................................................3-12

Analog Interconnections ....................................................................................................3-12

Digital Interconnections (4100-1311 Digital Audio Controller) ...........................................3-13

Chapter 4 Networking ........................................................................................ 4-1Introduction ..........................................................................................................................4-1

In this chapter ......................................................................................................................4-1

Introduction to the 4100 Network Interface Card .......................................................... 4-2Overview ..............................................................................................................................4-2

Network Module Illustrations ................................................................................................4-3

NIC Card LED Indications ....................................................................................................4-34100 Motherboard Options ..................................................................................................4-4

NIC Card Modules ...............................................................................................................4-5

Requirements and Limitations .............................................................................................4-6

11

Table of Contents

Step 1. Configuring Network Cards ............................................................................... 4-7Overview ..............................................................................................................................4-7

Motherboard Jumper Settings ..............................................................................................4-7

NIC Card Address Setting ....................................................................................................4-7NIC Card Jumper Settings ...................................................................................................4-7

Wired Media Card Jumper Settings .....................................................................................4-7

Modem Media Card Jumper Settings ..................................................................................4-8Fiber Media Jumper Settings (746-109 only) .......................................................................4-8

Step 2. Mounting Media Cards to the NIC ..................................................................... 4-9Overview ..............................................................................................................................4-9Media Card Mounting ...........................................................................................................4-9

Step 3. Mounting Network Cards .................................................................................4-10Daughter Card Installing ....................................................................................................4-10

Step 4. Wiring Network Cards ...................................................................................... 4-11Overview ............................................................................................................................4-11

Wiring Guidelines ...............................................................................................................4-11Wiring Distances ................................................................................................................4-12

Related Documentation .....................................................................................................4-12

Fiber-Optic Wiring ..............................................................................................................4-13Fiber Optic Connection Types ...........................................................................................4-13

4190-9010 Coupler Requirements .....................................................................................4-14

Wiring with the Wired Media Card .....................................................................................4-15Modem Guidelines .............................................................................................................4-17

Modem Wiring ....................................................................................................................4-17

Wiring Illustrations ..............................................................................................................4-18Wired Media Style 7 Wiring ................................................................................................4-18

Fiber Optic Style 7 Wiring ..................................................................................................4-19

Wired Media and Fiber Optic Style 7 Wiring ......................................................................4-20Modem Media Wiring (Non-4100ES/4100U Only) .............................................................4-21

Network Audio Wiring ................................................................................................... 4-22Head-End Audio Network Configuration ............................................................................4-22Locations on the Network Audio Riser Controller Module .................................................4-22

Card Specifications ............................................................................................................4-23

Analog Interconnections ....................................................................................................4-24

Digital Interconnections for the 4100-1311 Digital Audio Controller ..................................4-25Distributed Microphone Interconnections ...........................................................................4-26

Reference for MCC DARIC Installation ..............................................................................4-26

Digital Audio PDI Termination Plug ............................................................................. 4-27Overview ............................................................................................................................4-27

Installing a Digital Audio PDI Termination Plug .................................................................4-27

Chapter 5 The System Power Supply (SPS) .................................................... 5-1Introduction ..........................................................................................................................5-1In this chapter ......................................................................................................................5-1

SPS Specifications .......................................................................................................... 5-2Input/Output/Battery Specifications ......................................................................................5-2SPS Current Consumption ...................................................................................................5-3

SPS Configuration ........................................................................................................... 5-4Overview ..............................................................................................................................5-4

12

Table of Contents

Jumper Settings ...................................................................................................................5-4

Setting the Device Address ..................................................................................................5-4

SPS LED Indications ....................................................................................................... 5-5LEDs ....................................................................................................................................5-5

Troubleshooting .............................................................................................................. 5-6Overview ..............................................................................................................................5-6

IDNet Power Monitor Trouble ..............................................................................................5-6

Extra Device .........................................................................................................................5-6Class A Trouble ...................................................................................................................5-6

Earth Fault Search ...............................................................................................................5-6

Short Circuit .........................................................................................................................5-6Channel Fail .........................................................................................................................5-6

No Answer/Bad Answer .......................................................................................................5-6

Output Abnormal ..................................................................................................................5-6

Chapter 6 4100ES SPS Field Wiring ................................................................ 6-1Introduction ..........................................................................................................................6-1

In this chapter ......................................................................................................................6-1

General Field Wiring Guidelines .................................................................................... 6-2General Guidelines ..............................................................................................................6-2

Power-Limited Guidelines ....................................................................................................6-3

Power Supply Wiring Distances ..................................................................................... 6-5Overview ..............................................................................................................................6-5

Class A NAC Wiring Table ...................................................................................................6-5

Class B NAC Wiring Table ...................................................................................................6-6

SPS NAC Field Wiring Guidelines .................................................................................. 6-7Guidelines ............................................................................................................................6-7

SPS NAC Wiring .............................................................................................................. 6-8Class A NAC Wiring .............................................................................................................6-8

Class B NAC Wiring .............................................................................................................6-9

SPS IDNet Field Wiring Guidelines .............................................................................. 6-10IDNet Wiring .......................................................................................................................6-10

Guidelines ..........................................................................................................................6-10

SPS IDNet Wiring ........................................................................................................... 6-11Class A Wiring ...................................................................................................................6-11Class B Wiring ...................................................................................................................6-12

SPS Auxiliary Power Wiring ......................................................................................... 6-13Guidelines ..........................................................................................................................6-13Wiring .................................................................................................................................6-14

SPS Auxiliary Relay Wiring .......................................................................................... 6-15Guidelines ..........................................................................................................................6-15Wiring .................................................................................................................................6-15

Chapter 7 EPS with IDNet 2 ............................................................................... 7-1Introduction ..........................................................................................................................7-1

In this chapter ......................................................................................................................7-1

EPS Specifications .......................................................................................................... 7-2Card Specifications ..............................................................................................................7-2

13

Table of Contents

EPS Configuration ........................................................................................................... 7-3Setting the EPS Address .....................................................................................................7-3

Earth Connect Jumper .........................................................................................................7-4

Battery Disconnect Jumper ..................................................................................................7-4

EPS IDNet 2 Configuration .............................................................................................. 7-5Setting the Address ..............................................................................................................7-5

Connections ..................................................................................................................... 7-6Connection to the Power Distribution Module ......................................................................7-6

Troubleshooting .............................................................................................................. 7-7LED Trouble Indicator Overview ..........................................................................................7-7System Trouble LED Codes ................................................................................................7-7

SLC Channel Trouble LED Codes .......................................................................................7-8

Trouble Messages ...............................................................................................................7-9

Chapter 8 EPS and IDNet 2 Wiring ................................................................... 8-1Introduction ..........................................................................................................................8-1

In this chapter ......................................................................................................................8-1

EPS Wiring Overview ...................................................................................................... 8-2General Wiring Guidelines ...................................................................................................8-2

Power-Limited Guidelines ....................................................................................................8-2

EPS Class B IDNAC Wiring ............................................................................................. 8-3Wiring Overview ...................................................................................................................8-3

IDNAC Wiring Guidelines .....................................................................................................8-3

IDNAC Speaker Wiring Application Guidelines ....................................................................8-3Ferrite Beads .......................................................................................................................8-4

EPS Wiring Tables ........................................................................................................... 8-5Class B Wiring Tables ..........................................................................................................8-5

EPS Wiring to Devices .................................................................................................... 8-7Class B Wiring to IDNAC Devices .......................................................................................8-7

4009 IDNAC Repeater .........................................................................................................8-7Dual Class A Isolator (DCAI) ...............................................................................................8-7

Calculating Class B wiring with Isolators .............................................................................8-8

EPS Auxiliary Power Wiring ........................................................................................... 8-9AUX/ NAC Terminal .............................................................................................................8-9

IDNet 2 Card Wiring ....................................................................................................... 8-10Wiring Overview .................................................................................................................8-10

Wiring Parameters .............................................................................................................8-10Class A Wiring ...................................................................................................................8-11

Class B Wiring ...................................................................................................................8-12

Chapter 9 PC Software Connections ............................................................... 9-1Introduction ..........................................................................................................................9-1In this chapter ......................................................................................................................9-1

Software Modes ............................................................................................................... 9-2Software Modes ...................................................................................................................9-2

Ethernet Service Port and Serial Service Port .............................................................. 9-4Ethernet Service Port Overview (0566-719 only) .................................................................9-4

Serial Service Port Overview ...............................................................................................9-4

14

Table of Contents

Chapter 10 MNS/ECS Application .................................................................. 10-1Introduction ........................................................................................................................10-1

In this chapter ....................................................................................................................10-1

Application of 4100ES as a UL2572 Mass Notification System ................................. 10-2General Information ...........................................................................................................10-2

Hierarchy of Operator Interfaces ........................................................................................10-2

Priority of Signals ...............................................................................................................10-3Overriding Fire Alarm Signals ............................................................................................10-3

Timing Equations ...............................................................................................................10-4

Appliance Control Equations ..............................................................................................10-4Public Accessible Panic Switches ......................................................................................10-4

Programming and Configuration .................................................................................10-5Programming the 4100ES to Meet MNS Requirements ....................................................10-5Minimum Configuration for LOC and ACU .........................................................................10-5

Access and Security Information for the 4100ES System .................................................10-6

Voice Control Centers ........................................................................................................10-6Configuration Limitations ...................................................................................................10-6

Amber Strobes ...................................................................................................................10-7

MNS Wiring ........................................................................................................................10-7

Appendix A The Device Configuration DIP Switch .........................................A-1Overview ............................................................................................................................. A-1

The Service Port ............................................................................................................. A-2Overview ............................................................................................................................. A-2

Chapter B Installing 4100 FACP Components (Non-4100ES/4100U) ............B-1Introduction ......................................................................................................................... B-1In this chapter ..................................................................................................................... B-1

Introduction to FACPs .................................................................................................... B-2Overview ............................................................................................................................. B-2Master Controller Bay ......................................................................................................... B-2

Master Motherboards and Controllers ................................................................................ B-3

Universal Power Supply (UPS) ........................................................................................... B-5

Operator Interface ............................................................................................................... B-6Additional CPU Bay Modules .............................................................................................. B-6

Expansion Bays .................................................................................................................. B-6

System Power ..................................................................................................................... B-7

Step 1. Mounting Back Boxes ....................................................................................... B-8Overview ............................................................................................................................. B-8

Specifications ...................................................................................................................... B-8Installing the Back Box(es) ................................................................................................. B-9

Step 2. Mounting Electronics Bays to Back Boxes ................................................... B-10Overview ........................................................................................................................... B-10Installing the System Electronics Bays ............................................................................. B-10

Step 3. Configuring Modules ....................................................................................... B-14Overview ........................................................................................................................... B-14Master Motherboard Configuration ................................................................................... B-14

565-333 Master Controller Configuration .......................................................................... B-14

565-148 Master Controller Configuration .......................................................................... B-15

15

Table of Contents

UPS Configuration ............................................................................................................ B-15

Configuring Other Cards ................................................................................................... B-16

Step 4. Interconnecting Master Controller Bay Cards .............................................. B-17Overview ........................................................................................................................... B-17

Interconnecting Cards ....................................................................................................... B-17

Step 5. Installing Motherboards into Expansion Bays .............................................. B-18Overview ........................................................................................................................... B-18

Guidelines ......................................................................................................................... B-18Installing Motherboards ..................................................................................................... B-18

Connecting the 733-525 Harness ..................................................................................... B-19

Chapter C Installing 4100 MINIPLEX Components (Non-4100ES/4100U) ....C-1Introduction ......................................................................................................................... C-1In this chapter ..................................................................................................................... C-1

Introduction to MINIPLEX Systems ............................................................................... C-2Overview ............................................................................................................................. C-2

MINIPLEX System Components .................................................................................... C-4Overview ............................................................................................................................. C-4

The RUI Card ...................................................................................................................... C-4Transponder Cabinets ........................................................................................................ C-4

The Remote Interface Card (RIC) ....................................................................................... C-5

MINIPLEX System Guidelines ....................................................................................... C-6Overview ............................................................................................................................. C-6

Guidelines ........................................................................................................................... C-6

Installing Modules into Back Boxes ............................................................................. C-7Overview ............................................................................................................................. C-7

Guidelines ........................................................................................................................... C-7

Installing the RUI Motherboard ........................................................................................... C-7Installing the RIC II Motherboard ........................................................................................ C-8

Connecting the 733-525 Harness ....................................................................................... C-9

MINIPLEX Wiring .......................................................................................................... C-11Overview ........................................................................................................................... C-11

Wiring Configurations ........................................................................................................ C-11

Class A Wiring .................................................................................................................. C-11

Class B Wiring .................................................................................................................. C-11Wiring Illustration .............................................................................................................. C-12

Appendix D Checking System Wiring ..............................................................D-1Overview ............................................................................................................................. D-1

Using the Volt/ Ohm Meter .................................................................................................. D-1

Checking System Wiring ............................................................................................... D-2Meter Readings ................................................................................................................... D-2

Appendix E References to 4100ES Module Installation Instructions ...........E-1Overview ............................................................................................................................. E-1

Appendix F Labels .............................................................................................F-1

16

Table of Contents

Appendix G Earth Fault Diagnostics ............................................................... G-1Overview .............................................................................................................................G-1In this chapter .....................................................................................................................G-1

General Guidelines ......................................................................................................... G-2General Guidelines .............................................................................................................G-2

Earth Fault Searching from the Front Panel ................................................................ G-3Overview .............................................................................................................................G-3

Access Level Selection .......................................................................................................G-3Starting the Earth Fault Search ...........................................................................................G-3

Search Option A: Select Location .......................................................................................G-4

Search Option B: Select Channel .......................................................................................G-5Search Option C: Last Search Result .................................................................................G-5

Completing the Search .......................................................................................................G-5

Search Results ................................................................................................................ G-6Overview .............................................................................................................................G-6

Non-Point Faults .................................................................................................................G-6

Point Faults .........................................................................................................................G-6Fault Not Found ..................................................................................................................G-7

No Fault ..............................................................................................................................G-7

Result Not Available ............................................................................................................G-7

Earth Fault Search Example .......................................................................................... G-8Earth Fault Search Example ...............................................................................................G-8

Appendix H Special Application NAC-Compatible Notification Appliances and Accessories ........................................................................................................H-1

Appendix I EPS Compatible Appliances and Devices ..................................... I-1EPS Compatible Devices ......................................................................................................I-1EPS Compatible Appliances .................................................................................................I-1

Appendix J Cooper Wheelock Appliances Compatible With 4100ES Wheelock Protocol For Special Applications ................................................................... J-1

Overview ..............................................................................................................................J-1

Synchronizing Horn Strobes ................................................................................................J-1Synchronizing strobes ..........................................................................................................J-2

Appliances with synchronizing strobes ................................................................................J-3

Synchronizing horns ............................................................................................................J-4Coded audible appliances ....................................................................................................J-5

Non-synchronizing appliances .............................................................................................J-5

Appendix K Audio Equipment Compatible with 520 Hz Low Frequency Alarm K-1Overview ............................................................................................................................. K-1

Compatible Audio System Components ............................................................................. K-1Compatible Notification Appliances .................................................................................... K-2

Audio Options Alongside Compatible Equipment ............................................................... K-3

17

Figure 1-1. Standalone 4100ES System.............................................................................. 1-3Figure 1-2. MINIPLEX 4100ES System .............................................................................. 1-5Figure 1-3. Hub/Ring Configuration .................................................................................... 1-6Figure 1-4. Interconnected Loop Configuration................................................................... 1-7Figure 2-1. The CPU Bay..................................................................................................... 2-2Figure 2-2. Master Motherboard (566-227)......................................................................... 2-3Figure 2-3. Master Controller Daughter Card (566-719) ..................................................... 2-4Figure 2-4. System Power Supply (566-071) ...................................................................... 2-6Figure 2-5. The Power Distribution Interface (PDI) ............................................................. 2-7Figure 2-6. RUI+ CPU Master Motherboard (566-938)....................................................... 2-7Figure 2-7. Master Controller Daughter Card (566-719) ..................................................... 2-8Figure 2-8. EPS with IDNet 2 (566-872) ........................................................................... 2-10Figure 2-9. IDNet 2 Card................................................................................................... 2-11Figure 2-10. Operator Interface......................................................................................... 2-12Figure 2-11. Flexible User Interface.................................................................................. 2-12Figure 2-12. Expansion Bays ............................................................................................ 2-13Figure 2-13. System Power............................................................................................... 2-14Figure 2-14. Back Box Installation Diagram...................................................................... 2-16Figure 2-15. Back Box side views (plastic and metal doors).............................................. 2-17Figure 2-16. Removing the Shipping Studs ...................................................................... 2-18Figure 2-17. Mounting the PDM Bracket (2-Bay Box Shown)........................................... 2-19Figure 2-18. Installing the System Electronics Bay Assembly .......................................... 2-20Figure 2-19. Semi-Flush Trim Kit ...................................................................................... 2-21Figure 2-20. Applying the Trim.......................................................................................... 2-21Figure 2-21. Front and Back View of a Glass Door........................................................... 2-22Figure 2-22. Front and Back view of a Solid Door ............................................................ 2-22Figure 2-23. Reversing the Lock Catch............................................................................. 2-23Figure 2-24. Securing the Dress Panel ............................................................................. 2-23Figure 2-25. Hinge Pin Alignment ..................................................................................... 2-23Figure 2-26. The Ground Wire .......................................................................................... 2-24Figure 2-27. CPU Bay Card Placement ............................................................................ 2-25Figure 2-28. Expansion Bay 4” X 5” Card Placement ....................................................... 2-26Figure 2-29. Expansion Bay Motherboard Placement ...................................................... 2-27Figure 2-30. Mixed Module Placement ............................................................................. 2-28Figure 2-31. Slave Card/PDI Connection.......................................................................... 2-29Figure 2-32. Installing the Motherboard in a 4100ES Expansion Bay............................... 2-30Figure 2-33. Wiring Looped Through Ferrite Bead ........................................................... 2-31Figure 2-34. FACP Power Supply Assembly Connector (EPS shown)............................. 2-32Figure 2-35. XPS/PDM Connection .................................................................................. 2-33Figure 2-36. Bay-to-Bay Interconnections......................................................................... 2-34Figure 2-37. Basic CPU Interconnections ......................................................................... 2-37Figure 2-38. Power and Communication Wiring for Motherboards ................................... 2-38Figure 2-39. One Bay Battery Installation ......................................................................... 2-41Figure 2-40. Multi-Bay Battery Installation ........................................................................ 2-42Figure 2-41. Terminal Block Utility Module Mounting........................................................ 2-44Figure 3-1. Transponder Interface Cards............................................................................. 3-4Figure 3-2. TIC Mounting .................................................................................................... 3-9Figure 3-3. Transponder Cabinet Interconnections........................................................... 3-10Figure 3-4. Loop Wire Through Ferrite Bead as Shown ................................................... 3-11Figure 3-5. TIC Wiring to the Host Panel .......................................................................... 3-11Figure 3-6. Analog Audio Interconnections ....................................................................... 3-12Figure 3-7. Digital Interconnections (4100-1311 Digital Audio Controller) ........................ 3-13Figure 4-1. 4100-6014 Network Interface Card.................................................................... 4-3Figure 4-2. UT Motherboard with City Connection (565-274) ............................................. 4-4Figure 4-3. UT Motherboard without City Connection (565-275) ........................................ 4-4Figure 4-4. The 4100/4120-0143/ 4100-6057 Fiber-Optic Media Card............................... 4-5Figure 4-5. The 4100/4120-0142 Wired Media Card (565-413).......................................... 4-5Figure 4-6. The 4100-6055 Modem Media Card (565-279 or 566-338).............................. 4-6Figure 4-7. Media Card Mounting ....................................................................................... 4-9Figure 4-8. Installing the Daughter Card ........................................................................... 4-10Figure 4-9. The Transient Suppressor .............................................................................. 4-12Figure 4-10. Fiber Wiring .................................................................................................. 4-13Figure 4-11. Coupler Wiring .............................................................................................. 4-15

List of Figures

18

Figure 4-12. Wired Media Interconnections Between 4100ES Motherboards .................. 4-16Figure 4-13. Modem Wiring............................................................................................... 4-17Figure 4-14. Wired Media, Style 7 Wiring ......................................................................... 4-18Figure 4-15. Fiber Optic, Style 7 Wiring ............................................................................ 4-19Figure 4-16. Wired Media and Fiber Optic, Style 7 Wiring................................................ 4-20Figure 4-17. Modem Media Wiring (Non-4100ES/4100U Only)........................................ 4-21Figure 4-18. Network Audio Riser Controller Module........................................................ 4-22Figure 4-19. Analog Audio Interconnections ..................................................................... 4-24Figure 4-20. Digital Audio Interconnections (4100-1311 Digital Audio Controller)............ 4-25Figure 4-21. Distributed Microphone Interconnections ..................................................... 4-26Figure 4-22. Installing a Digital Audio PDI Termination Plug ............................................ 4-27Figure 6-1. Power-Limited Wiring......................................................................................... 6-3Figure 6-2. The EOL Relay ................................................................................................. 6-4Figure 6-3. Class A NAC Wiring.......................................................................................... 6-8Figure 6-4. Class B Wiring .................................................................................................. 6-9Figure 6-5. Loop Wiring as Shown.................................................................................... 6-10Figure 6-6 . Class A Wiring ............................................................................................... 6-11Figure 6-7. Class B Wiring ................................................................................................ 6-12Figure 6-8. Auxiliary Power Wiring.................................................................................... 6-14Figure 6-9. Auxiliary Relay Wiring..................................................................................... 6-15Figure 7-1. EPS Card Layout .............................................................................................. 7-2Figure 7-2. DIP Switch SW2 ............................................................................................... 7-3Figure 7-3. Earth Connect Jumper Positions ...................................................................... 7-4Figure 7-4. Battery Disconnect Jumper Positions ............................................................... 7-4Figure 7-5. DIP Switch SW1 ............................................................................................... 7-5Figure 7-6. PDM/Battery Connections ................................................................................ 7-6Figure 7-7. LED Location .................................................................................................... 7-7Figure 8-1. Power-Limited Wiring Guidelines...................................................................... 8-2Figure 8-2. Ferrite Bead Installation.................................................................................... 8-4Figure 8-3. Class B Wiring .................................................................................................. 8-7Figure 8-4. Class B Wiring With Isolators ........................................................................... 8-8Figure 8-5. AUX/NAC Terminal........................................................................................... 8-9Figure 8-6. Simple NAC Wiring ........................................................................................... 8-9Figure 8-7. Class A Jumper Setting .................................................................................. 8-11Figure 8-8. IDNet 2 Class A Wiring ................................................................................... 8-11Figure 8-9. Class B Jumper Setting .................................................................................. 8-12Figure 8-10. IDNet 2 Class B Wiring ................................................................................. 8-12Figure 9-1. Service and Diagnostic Interface ....................................................................... 9-2Figure 9-2. Data Transfer Interface..................................................................................... 9-2Figure 9-3. Bootloader Interface ......................................................................................... 9-3Figure 9-4. CPU card ports ................................................................................................. 9-4Figure 9-5. Front Panel Ethernet Service Port .................................................................... 9-4Figure 10-1. Supervisory and Trouble LEDs for both MNS and Fire ................................. 10-5Figure 10-2. Voice Message Configuration Example........................................................ 10-6Figure A-1. DIP Switch SWx ................................................................................................ A-1Figure B-1. Master Controller Bay (4100) ............................................................................ B-2Figure B-2. UT Motherboard (565-161)............................................................................... B-3Figure B-3. UT Motherboard with City Connection (565-213)............................................. B-3Figure B-4. UT Motherboard with City Connection (565-274)............................................. B-3Figure B-5. UT Master Controller (565-333) ....................................................................... B-4Figure B-6. UT Master Controller (565-148) ....................................................................... B-4Figure B-7. Universal Power Supply ................................................................................... B-5Figure B-8. Operator Interface ............................................................................................ B-6Figure B-9. Master Controller and Expansion Bays ............................................................ B-6Figure B-10. Power and Comm Lines ................................................................................. B-7Figure B-11. Back Box Installation Diagram ....................................................................... B-9Figure B-12. Removing the Shipping Studs ...................................................................... B-10Figure B-13. Inserting the Mounting Screws..................................................................... B-11Figure B-14. Installing the System Electronics Bay Assembly.......................................... B-12Figure B-15. Master Controller Bay Interconnections ....................................................... B-17Figure B-16. Installing the Motherboard in an Expansion Bay .......................................... B-18Figure B-17. Power and Communication Wiring for Motherboards................................... B-20Figure C-1. MINIPLEX System Design ................................................................................C-3

List of Figures

19

Figure C-2. The Remote Unit Interface Card ...................................................................... C-4Figure C-3. The RIC II Card ................................................................................................ C-5Figure C-4. Installing the RUI Motherboard in the CPU Bay............................................... C-7Figure C-5. Installing the RIC II Motherboard into a 4100 Expansion Bay.......................... C-8Figure C-6. Power and Communication Wiring for the Transponder Cabinet (4100) ....... C-10Figure C-7. MINIPLEX Wiring ........................................................................................... C-12Figure G-1. Earth Fault Example .........................................................................................G-8

List of Figures

20

Table 2-1. CPU Components ..............................................................................................2-2Table 2-2. Master Controller Bootloader LEDs ....................................................................2-5Table 2-3. Master Controller Switches ................................................................................2-5Table 2-4. Master Controller Bootloader LEDs ....................................................................2-9Table 2-5. Master Controller Switches ................................................................................2-9Table 2-6. Power Requirements ........................................................................................2-14Table 2-7. Contents of the Back Box Bay Mounting Hardware Kit ....................................2-15Table 2-8. Recommended Torque for Mounting Hardware ...............................................2-18Table 3-1.TIC Specifications ...............................................................................................3-6Table 4-1. Electrical and Environmental Specifications .......................................................4-6Table 4-2. Wiring Distances ..............................................................................................4-12Table 4-3. Dual Fiber Optic Cable Communications Distance Examples ..........................4-14Table 4-4. Single Fiber Optic Cable Communications Distance Examples* ......................4-14Table 4-5. CPU Motherboard Wired Media Connections ..................................................4-16Table 4-6. Network Audio Riser Controller Specifications .................................................4-23Table 5-1. Input and Output Specifications .........................................................................5-2Table 5-2. SPS Current Specifications ................................................................................5-3Table 6-1. Class A Wiring Distances ...................................................................................6-5Table 6-2. Class B Wiring Distances ...................................................................................6-6Table 7-1. Card Specifications ............................................................................................7-2Table 7-2. EPS Card Addresses .........................................................................................7-3Table 7-3. 4100-3109 Card Addresses ...............................................................................7-5Table 7-4. The 8 EPS indicator LEDs. ................................................................................7-7Table 7-5. System Trouble LED Codes ...............................................................................7-7Table 7-6. SLC Channel Trouble LED Codes .....................................................................7-8Table 7-7. EPS Trouble Messages ......................................................................................7-9Table 8-1. UTP Wiring Limit Based on Alarm Current .........................................................8-5Table 8-2. UTP Wiring Limit Based on Communication ......................................................8-5Table 8-3. Ohms per 1000 ft ................................................................................................8-5Table 8-4. UTP Wiring Limit for Speakers and Speaker/Visible devices based on Communication 8-6Table 8-5. AUX/NAC Wiring Specification ...........................................................................8-9Table 8-6. NAC Wiring Limits ..............................................................................................8-9Table 8-7. IDNet 2 Card Wiring Parameters ......................................................................8-10Table 10-1. Minimum Configuration for LOC and ACU .....................................................10-5Table A-1. Card Addresses ................................................................................................ A-2Table B-1. Back Box Specifications .................................................................................... B-8Table B-2. Contents of the Back Box Mounting Hardware Kit ............................................ B-8Table B-3. Recommended Torque for Mounting Hardware .............................................. B-12Table B-4. UPS SW1 Battery Configurations ................................................................... B-15Table D-1. Acceptable Zone and Signal Circuit Meter Readings ....................................... D-2Table E-1. References to 4100ES module installation instructions .................................... E-1Table H-1. Special Application NAC-Compatible Notification Appliances and Accessories H-1Table I-1. Compatible Devices ............................................................................................. I-1Table I-2. Compatible Appliances ......................................................................................... I-1Table J-1. Synchronizing Horn Strobes ............................................................................... J-1Table J-2. Synchronizing strobes ........................................................................................ J-2Table J-3. Appliances with synchronizing strobes ............................................................... J-3Table J-4. Synchronizing horns ........................................................................................... J-4Table J-5. Coded audible appliances .................................................................................. J-5Table J-6. Non-synchronizing appliances ............................................................................ J-5Table K-1. Compatible Audio System Components ........................................................... K-1Table K-2. Compatible Notification Appliances .................................................................. K-2Table K-3. Audio Options That May Be Configured Alongside Compatible Equipment ..... K-3

List of Tables

1-1

Chapter 1

Introduction to the 4100ES Fire Alarm System

Introduction The 4100ES is an expandable fire alarm system that can be used as a standalone system with one host panel, or as a wide-ranging system with several remote back boxes, with or without multiple host panels. This chapter is an overview of standalone, MINIPLEX®, and network 4100E