3-1 ansys, inc. proprietary © 2009 ansys, inc. all rights reserved. april 28, 2009 inventory...
TRANSCRIPT
3-1ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Chapter 3
Solver Basics
Introductory FLUENT TrainingSharif University of TechnologyLecturer: Ehsan [email protected]
Solver Basics
3-2ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualFLUENT 12 GUI Navigation
• The FLUENT GUI is arranged such that the tasks are generally arranged from top to bottom in the project setup tree.
• Selecting an item in the tree opens the relevant input items in the center pane.
– General– Models– Materials– Boundary
Conditions– Solver Settings– Initialization and
Calculation– Postprocessing
Solver Basics
3-3ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualScaling the Mesh and Selecting Units• When FLUENT reads a mesh
file (.msh), all physical dimensions are assumed to be in units of meters.
– If your model was not built in meters, then it must be scaled.
– Verify that the Domain Extents are correct after scaling the mesh.
• When importing a mesh under Workbench, the mesh does not need to be scaled; however, the units are set to the default MKS system.
• Any “mixed” units system can be used if desired.
– By default, FLUENT uses the SI system of units (specifically, MKS system).
– Any units can be specified in the Set Units panel, accessed from the top menu.
Define Units…
Solver Basics
3-4ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualText User Interface• Most GUI commands
have a corresponding TUI command.
– Many advanced commands are only available through the TUI.
– Press the Enter key to display the command set at the current level.
– q moves up one level.
• FLUENT can be run in batch mode or scripted using a journal file (seeAppendix)
• A TUI user guide is available on the FLUENT User Services Centerwww.fluentusers.com
Solver Basics
3-5ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualMouse Functionality• Mouse button functionality depends on the chosen solver (2D / 3D)
and can be configured in the solver.• Default settings
– 2D Solver• Left button translates/pans (dolly)• Middle button zooms• Right button selects/probes
– 3D Solver• Left button rotates about 2 axes• Middle button zooms
– Middle click on point in screen centers point in window
• Right button selects/probes
• Retrieve detailed flow field information at point with Probe enabled.– Right-click on the graphics display.
• Mouse controls can be set to emulate those in Workbench!
Display Mouse Buttons…
Solver Basics
3-6ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualMaterial Properties• FLUENT provides a standard
database of materials and theability to create a customuser-defined database.
• Your choice of physical modelsmay require multiple materialsand dictate which materialproperties must be defined.
– Multiphase (multiple materials)– Combustion (multiple species)– Heat transfer (thermal
conductivity)– Radiation (emissivity and
absorptivity)
• Material properties can be directly customized as function of temperature/pressure
– Use of other solution variable(s) requires UDF.
Solver Basics
3-7ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualMaterials Databases
• FLUENT materials database– Provides access to a number
of pre-defined fluid, solid and mixture materials.
– Materials can be copied to the case file and edited if required.
• Custom material database: – Create a new custom database
of material properties and reaction mechanisms from materials in an existing case file for reuse in future cases.
– Custom databases can be created, accessed and modified from the standard materials panel in FLUENT.
Solver Basics
3-8ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualOperating Conditions
• The Operating Pressure with a Reference Pressure Location sets the reference value that is used in computing gauge pressures.
• The Operating Temperature sets the reference temperature(used when computing buoyancy forces.
• Specified Operating Density sets the reference value for flows with widely varying density.
Solver Basics
3-9ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualParallel Processing• Parallel processing can be used to run
FLUENT on multiple processors to decrease turnaround time and increase simulation efficiency.
– Critical for cases involving large meshes and/or complex physics.
– FLUENT is fully parallelized and capable of running across most hardware and software configurations, such as compute clusters or multi-processor machines.
• Parallel FLUENT can be launched either using the system command prompt or using the FLUENT Launcher panel.
– For example, to launch an n-CPU parallel session, use the commandfluent 3d –tn
• The mesh can be partitioned either manually or automatically using a number of different methods.
– Non-conformal meshes, sliding mesh interfaces and shell conduction zones require partitioning in serial.
• A web-based lecture is available on the FLUENT User Services Center.
Solver Basics
3-10ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualSummary
• This lecture has presented many basic tasks that are often performed during a CFD simulation setup.
• Parallel processing can be used to reduce calculation time. This is advantageous only on large meshes.
• A later lecture contains material related to the setup and solution of time-dependent problems.
• Other topics not discussed (see Appendix for information).– Mesh heirarchy and relationships.– Reordering and modifying the mesh in the solver.– Polyhedral mesh conversion.– Solution-based mesh adaption.
3-11ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Appendix
Solver Basics
3-12ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualFLUENT Journals• FLUENT can be run in batch mode using
journal files.• A journal file is a text file which contains
TUI commands which FLUENT will execute sequentially.
• The FLUENT TUI accepts abbreviations of the commands; for example,
– ls Lists the files in the working folder
– rcd Reads case and data files – wcd Writes case and data files – rc/wc Reads/writes case file– rd/wd Reads/writes data file– it Iterate
• TUI commands in a batch file can be used to automate operations in a non-interactive mode.
– The TUI commands file/read-bc and file/write-bc can be used for reading and writing the settings for a FLUENT session to and from a file, respectively.
– A web-based training module is available which explains this process
; Read case filerc example.cas.gz; Initialize the solution/solve/initialize/initialize-flow; Calculate 50 iterationsit 50; Write data filewd example50.dat.gz; Calculate another 50 iterationsit 50; Write another data filewd example100.dat.gz; Exit FLUENTexityes
Sample Journal File
Solver Basics
3-13ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualReading the Mesh – Zones
• In this example, there are two cell zones (fluid-upstream and fluid-downstream).
• Because of this, FLUENT splits the exterior wall zone into two zones (wall and wall:001). This is because an external boundary cannot span multiple cell zones.
• FLUENT also splits the orifice plate into two walls also (plate and plate-shadow) since the plate zone is an internal wall.
inlet
outlet
wall
plateplate-shadow
fluid (cell zone)
Default-interior zone(s)can always be ignored.
Solver Basics
3-14ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualMesh Information and Hierarchy• All mesh information is stored in the mesh file.
– Node coordinates– Connectivity– Zone definition
• Similar to the way geometry is defined, mesh entities obey a hierarchy:
– Node Edge intersection / grid point– Edge Boundary of a face (defined by
two nodes– Face The boundaries of cells, defined by
a collection of edges– Cell The control volumes into which the
domain is discretized.– Zone A collection of nodes, edges, faces
or cells.• The computational domain is defined by all
members of the hierarchy– For fluid flow simulation only, the domain consists
only of the fluid region.– For conjugate heat transfer or fluid-structure
interaction problems, the domain needs to include any solid parts that are present.
• Boundary data is assigned to face zones.• Material data and source terms are assigned to
cell zones.
Simple 3D mesh
Simple 2D Mesh
Node
BoundaryFace
Cell
CellCenter
Cell Face
Node
BoundaryFace
Cell
Edge
Solver Basics
3-15ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualReordering and Modifying the Grid• The grid can be reordered so that neighboring cells are near each
other in the zones and in memory– Improves efficiency of memory access and reduces the bandwidth of the
computation– Reordering can be performed for the entire domain or specific cell
zones.
– The bandwidth of each partition in the grid can be printed for reference.
• The face/cell zones can also be modified by the following operations in the Grid menu:
– Separation and merge of zones– Fusing of cell zones with merge of duplicate faces and nodes– Translate, rotate, reflect face or cell zones– Extrusion of face zones to extend the domain– Replace a cell zone with another or delete it– Activate and Deactivate cell zones
Grid Reorder ZonesGrid Reorder Domain
Grid Reorder Print Bandwidth
Solver Basics
3-16ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualPolyhedral Mesh Conversion• A tetrahedral or hybrid grid can be
converted to polyhedra in the FLUENT GUI (not in the preprocessor).
– Generate a tetrahedral mesh then convert inside FLUENT.
– Advantages • Improved mesh quality.• Can reduce cell count significantly.• User has control of the conversion process.
– Disadvantages: • Cannot be adapted or converted again.• Cannot use tools such as smooth, swap, merge
and extrude to modify the mesh.
• Two conversion options are available in the Grid menu:
– Convert all cells in the domain (except hex cells) to polyhedra
• Cannot convert meshes with hanging nodes• HexCore mesh can be converted using the tpoly
standalone utility.– Convert only highly skewed cells to
polyhedra
Grid Polyhedra Convert Skewed Cells
Grid Polyhedra Convert Domain
Tet/Hybrid Mesh
Polyhedral Mesh
Solver Basics
3-17ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualProfile Data and Solution Data Interpolation• FLUENT allows interpolation of selected
variable data on both face zones and cell zones by using profile files and data interpolation files, respectively.
– For example, a velocity profile from experimental data or previous FLUENT run at an inlet, or a solution interpolated from a coarse mesh to fine mesh.
• Profile files are data files which contain point data for selected variables on particular face zones, and can be both written and read in a FLUENT session.
• Similarly, Interpolation data files contain discrete data for selected field variables on particular cell zones to be written and read into FLUENT.
File Profile…Write
File Profile…Read
File Interpolate…
Solver Basics
3-18ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualMesh Adaption• Mesh adaption refers to refinement
and/or coarsening cells where needed to resolve the flow field without returning to the preprocessor.
– Mark cells satisfying the adaption criteria and store them in a “register.”
– Display and modify the register if desired.
– Click Adapt to adapt the cells listed in the register.
• Registers can be defined based on:– Gradients or isovalues of all variables– All cells on a boundary – All cells in a region with a defined
shape– Cell volumes or volume changes– y+ in cells adjacent to walls
• To assist adaption process, you can:– Combine adaption registers– Draw contours of adaption function– Display cells marked for adaption– Limit adaption based on cell size
and number of cells
Refine Threshold should be set to 10% of the value reported in the Max field.
Solver Basics
3-19ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualAdaption Example – Supersonic Projectile
• Adapt grid in regions of large pressure gradient to better resolve the sudden pressure rise across the shock.
Initial Mesh (Generated by Preprocessor) Pressure Contours on Initial Mesh
Large pressure gradient indicating a shock (poor resolution on coarse mesh)
Solver Basics
3-20ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002600
Training ManualAdaption Example – Supersonic Projectile
• Solution-based mesh adaption allows better resolution of the bow shock and expansion wave.
Mesh adaption yields much better resolution
of the bow shock.Adapted cells in locations of large pressure gradients
Adapted Mesh (Multiple AdaptionsBased on Gradients of Pressure)
Pressure Contours on Adapted Mesh