24 gage steel rta locker cabinet install instructions...

Install InstructIonsREAD THIS FIRST BEFORE UNPACKING CABINET

24 GAGE STEEl RTA lOCKER CABINET

DO NOT lEAvE CHIlDREN UNATTENDED NEAR CABINETS. WHEN FUlly lOADED, CABINETS ARE HEAvy AND THERE IS A RISK OF CABINETS OR ITEmS TIPPING IF ImPROPERly OPENED.

WARNING:DO NOT OvERlOAD CABINETS! CABINETS ARE DESIGNED TO CARRy THE FOllOWING mAxImUm WEIGHT CAPACITIES:

Cabinet Shelf Weight

Capacity (lbs)

Overall Weight

Capacity

Locker 50 200

Wall 40 80

Base 50 150

PARTS AND HARDWARE SUPPlIED WITH lOCKER CABINET:

WARNING: ExCESSIvE WEIGHT HAzARD• Use two or more people to move, assemble or install cabinet or

locker.• Failure to do so can result in back or other injury.

UNPACKING OF THE CABINET:• Begin by placing the cabinet on a sound level surface.• Remove all cardboard and foam packaging material.• Remove clear plastic bag.• Dispose / recycle all packaging materials.• Remove and verify all the contents in the box. See “Parts and

Hardware Supplied List”

QTy. ITEm ImAGE4 Hinge

47 M5 Frame Screw

47 M5 Frame Nut

4 Adjustable Leg

16 M8 Leg Screws

16 M8 Leg Screw Nut

4 M8 Big Washer

4 Plastic Washer

16 Lock Washers

4 2.5” Wall Screw

3 Hex Head Bolt

3 Small Washers

3 Small Lock Washers

3 Hex Head Nut

1 Work Top Bracket

need more information? try, WWW.NEWAGEPRODUCTS.COm or 1 877 306 8930 for answers to commonly asked questions.

All CABINETS mUST BE mOUNTED TO STUDS ON A SECURE WAll, AS PER THESE INSTRUCTIONS. FAIlURE TO DO SO mAy RESUlT IN SERIOUS INjURy AND vOIDS PRODUCT WARRANTy AND mANUFACTURER’S lIABIlITy.

Install InstructIons

I

A

B

H

I

GF

ED

C

G

G

A B C D

E F G H

Top Panel

Left Back Panel

Right Door

Bottom Panel

Right Back Panel

Corner Support

Left Panel

Shelf

Right Panel

Left Door




EF C

DA

B

G

G

G

H

I

1. Use the M5 screw and M5 nut to assemble the back panels.

2. Assemble the left and right side panels with the same screw and nut. D Goes on the outside of E, and C goes on the outside of F. *Use the M5 Screws and Nuts to attach the panels together.

3. Panel A sits on the outside of E and F, and on the inside of C and D. The same applies for panel B. Use the M5 Screws and Nuts to attach the panels together, after inserting piece Z in step 4.

4. Insert support piece Z into the front corner of the locker. Use the M5 Screws and nuts to attach piece Z to the sides and tops/bottom panels. Repeat this for all four front corners of the locker.




7. Put the four plastic washers in the holes at the four corners.

8. Assemble the right and left doors and insert the hinges into the plastic washers to attach doors. Bend down the clips to fix the hinges in place. Extra spacers are provided to ensure doors are level.


5. Flip the cabinet over. Use M8 screw, washer and M8 nut to assemble the adjustable legs on the bottom panel.

6. Turn the cabinet back upwards, then insert the shelf. If shelf tabs are not catching with the inside of panels D and C, pull the shelf notches outwards.


EF C

DA

B

G

G

G

H

I

ASSEmBly INSTRUCTIONS:CABINET lEvElING(for all cabinets except for wall cabinet)

1. Place a small magnetic level onto the top of the cabinet to verify the levelness of the cabinet.

2. If the floor slopes and the cabinet is not level, lift the adjustable sleeve on the leg and adjust the cabinets height-adjustable leveling leg by turning the nut on top of the cabinet’s foot, up or down to bring the cabinet to a level position. This may require two people, one person to verify / bring cabinet level and one person to adjust the legs up and down simultaneously.

3. The cabinet must be adjusted front to back and side to side.4. Do not put items in the cabinet until the leveling process is complete.

INSTAllING WORKTOP BRACKET:(optional, for locker cabinets)

NOTE:The worktop bracket is to be used in the event that a work top is added to the cabinetry system without a secondary supporting base lower cabinet. The installation of this bracket is made easier if the shelves are not yet in place, to provide more working space.

1. Open the locker doors and locate the three punched holes on either side of the locker cabinet.

2. Once side location is determined place the worktop bracket on the outside of the locker by aligning the holes in the locker with the holes in the bracket. Ensure the bracket is positioned with the side lip pointing up. See below diagram.

3. Using the supplied hardware put a hex head bolt through the bracket and then through the side of the locker cabinet. Once through put on a washer and a hex head nut. At this point the lock nuts should be only finger tight.

4. Repeat step 4 two more times for the remaining holes.5. Once all the bolts and nuts are in place level the bracket with a

small magnetic level.6. Once leveled, tighten the nuts firmly. This task may require 2

people for ease of installation.

mOUNTING OF THE WORKTOP:(optional, for base cabinets)

NOTE:Base Cabinet Drawers must be removed prior to mounting Worktop.

• Pull each drawer out to full extension, simultaneously depress the left lock down and right lock up in each slider while pulling out the drawer. The drawer will slide out of the tracks ready to remove. See the diagram to note where the locks are on the drawer slides.

1. Place the Worktop on top of both the base cabinet . 2. Align the Worktop so that it is flush with the side of the base

cabinet.3. Using the supplied Worktop hardware fasten screws through the

cabinet top into the Worktop. A cordless power drill is required to drive the screws into the Worktop.

4. Put drawers back into base cabinet by aligning them with the ball-bearing slides drawer tracks. The drawer should slide back into place. Push the drawer fully into the cabinet, then pull it out to full extension. If the drawer does not stop at full extension, or feels loose, the drawer has not been put back into the drawer slides properly. Ensure both drawer slides attached to the drawer are running along the drawer slides attached to the frame of the cabinet.

INSTAllING SHElvES:NOTE: Plan your shelf heights and install shelves starting from the

bottom. The shelves are supported by the metal tabs on the back and side walls of the cabinet.

1. Determine the placement of the shelves.2. Tilt the shelf so that one end is higher than the other as show in

the diagram below.

3. Insert the shelf into the cabinet so that the higher end is directly above the desired slots and push the shelf down into place behind the side slots.

Install InstructIons24 GAGE STEEl RTA lOCKER CABINET


Install InstructIons24 GAGE STEEl RTA lOCKER CABINET

4. Raise the lower end so it is directly above the desired slots and push the shelf down.

NOTE: Make sure all shelf tabs are completely in place, see below diagram.

5. Repeat steps 2 – 4 for the remaining shelves.Note:one shelf in the locker must be level with the lock on the

door of the cabinet, in order for the lock to work.

mOUNTING CABINETS INTO DRyWAll / STUDDED WAll:WARNING: All CABINETS mUST BE mOUNTED TO STUDS BEFORE lOADING THE CABINETS WITH ITEmSEach locker or base cabinet must be mounted to the wall with at least two of the provided mounting screws. Each wall cabinet must be mounted with four screws.

1. Using a stud finder locate the studs in the wall where the wall cabinet is to be placed.

2. Once studs are located, using a pencil and a level mark a vertical line to indicate stud location.

3. Place the cabinet into position tight against the supporting wall. 4. Open the doors and locate the perforated mounting strip on the

top and bottom of the backside of the cabinet. Note: the wall cabinet has a perforated strip of holes at the top

and bottom of the cabinet, the locker only has a perforated strip at the top of the cabinet.

5. Align the previously marked stud lines with a perforated hole by shifting the cabinet slightly.

6. Place a small magnetic level on top of the wall cabinet and adjust the orientation of the cabinet to bring it to a level position.

7. Once leveled, using the supplied mounting hardware fasten a 2.5” x ¼” cabinet mounting lag bolt with a large washer through the cabinet and into the stud. This can be done by hand with a 7/16th socket wrench or a cordless power drill with a 7/16th socket attachment. Do not over tighten bolts! Once the fender is sitting tightly flush with the backside of the cabinet stop.

8. Repeat Step 6 three additional times with the remaining mounting hardware to install the wall cabinet. You will only repeat this one more time for the locker, as it only has 2 mounting lag bolts.

WAll AND lOCKER CABINET WAll mOUNTING INTO CONCRETE BlOCK / mASONRy WAll:

NOTE:Masonry Hardware NOT IncludedREQUIRED HARDWARE:

• 2 ¼” x ¼” Tapcon Concrete Anchor (4) 0r •#10 x 2” Screw with 3/16” masonry plug (4)

1. Place the wall cabinet into position tight against the supporting wall.

2. Open the doors and locate the perforated mounting strip on the top and bottom of the backside of the cabinet.


4. Using a hammer drill, drill 4 pilot holes through the perforated strip in the backside of the cabinet and through the wall.

5. Using either the 2 ¼” x ¼” Tapcon Concrete Anchor or #10 x 2” Screw with 3/16” masonry plug method and the supplied fender washers fasten the cabinet directly to the wall. This application requires a cordless power dill with a #2 Philips bit for ease of installation.

6. Repeat Step 3 - 4 three additional times with the remaining mounting hardware.

THANK yOU for purchasing a NewAge product. Please give us a call, or visit us online if you have any other questions

or comments.

Give us your feedback for a chance to WIN! Take our quick 2 minute survey and enter for your chance to win something FREE from NEWAGE! Visit the website for details at www.newageproducts.com


newage Products Inc. wIll not Pay for: 1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.

2. Damage resulting from improper handling or shipping of products, or products damaged by accident, misuse, abuse, fire, flood, improper installation, acts of God, neglect, corrosion, modification or mishandling.

3. Products damaged by improperly loading beyond the specified maximum weight capacity outlined in the instructions provided with the product.

4. Repairs or replacement when your product is used in other than normal, single-family household use, such as a commercial environment, or handled in any way inconsistent with the installation instructions included with the product.

5. Cosmetic damage, including scratches, dings, dents or cracks in paint that do not affect the structural or functional capability of the product.

6. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.

7. Replacement parts for NewAge products outside Canada and the United States.

8. Replacement keys or locking mechanisms.

9. Loss of product contents due to left, fire, flood, accident or acts of God.

10. Shipping or freight fees to deliver replacement products or to return defective products.

11. Any labor costs during the limited warranty period.

dIsclaIMer of IMPlIed warrantIes; lIMItatIon of reMedIesIMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE

For one year from the date of purchase, when this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship.

newage Products Inc. steel cabInetry warranty1 year limited manufacturer warranty



24 GAGE STEEl RTA BASE CABINET








Capacity (lbs)

Overall Weight

Capacity

Locker 50 200

Wall 40 80

Base 50 150



PARTS AND HARDWARE SUPPlIED WITH BASE CABINET:QTy ITEm ImAGE4 Hinge

47 M5 Frame Screw

47 M5 Frame Nut

4 Adjustable Leg

16 M8 Leg Screws

16 M8 Leg Screw Nut

20 M8 Big Washer

4 Plastic Washer

16 Lock Washers

4 2.5” Wall Screw

4 5/8” Wood Screw

Install InstructIons24 GAGE STEEl RTA BASE CABINET

BC

AD

EF

G

H

I

A B C D

E F G H

I

Top Panel

Left Back Panel

Right Door

Bottom Panel

Right Back Panel

Left Panel

Shelf

Right Panel

Left Door



A

B

G

A

BA

B

HI

C

D

EF

1. Use the M5 screw and M5 nut to assemble the two back panels.

2. Assemble the left and right side panel with the same screw and nut. D Goes on the outside of E, and C goes on the outside of F.

3. Panel A sits on the outside of E and F, and on the inside of C and D.


6. Put the plastic washer in the holes at the four corners.

7. Assemble the right and left doors and insert hinges into the plastic washers. Bend down the clips to fix the hinges in place. Extra spacers are provided to ensure doors are level.

5. Turn the cabinet back upwards, then insert the shelf.If shelf tabs are not catching with the inside of panels D and C, pull the shelf notches outwards.



ASSEmBly INSTRUCTIONS:INSTAll THE HEIGHT-ADjUSTABlE STEEl lEvElING lEGS:(for all cabinets except for wall cabinet)

1. Open the cabinet and remove any loose shelves, support brackets, etc.

2. Close / lock the cabinet drawers. NOTE: If you need to open the cabinet / locker doors during

leveler assembly, open them slowly and do not put any weight on the open doors. This avoids damage to the cabinets hinges.

3. Using two or more people, place the cabinet / locker upside down. Using supplied packaging material to cushion the cabinet to prevent any scratching of the painted surfaces.

4. One at a time line up each height-adjustable leveling legs with the corners of the cabinet. The holes in the base of the cabinet should align with the holes in the adjustable leveling leg.

5. Using the Philips head socket, power drill or hand tighten the bolt with one small Foot Plate washer into each of the holes. There are 4 holes to attach the leveling leg to the base of the cabinets.

NOTE: Bolts should be snug. Do not over tighten or force bolts. This may result in the damaging of the threads.

NOTE: When assembling the Locker, Use the 16 smaller washers, not the 4 larger washers to fasten the legs. The 4 larger washers will be used for mounting to the wall, if necessary.

6. Repeat steps 3 – 5 for the remaining legs.7. Using two or more people, stand up the

cabinet and place into desired location.

CABINET lEvElING(for all cabinets except for wall cabinet)





NOTE: Base Cabinet Drawers must be removed prior to mounting Worktop.

• Pull each drawer out to full extension, simultaneously depress the left lock down and right lock up in each slider while pulling out the drawer. The drawer will slide out of the tracks ready to remove. See the diagram to note where the locks are on the drawer slides.





INSTAllING SHElvES:NOTE: Plan your shelf heights and install shelves starting from the

bottom. The shelves are supported by the metal tabs on the back and side walls of the cabinet.


the diagram below.






5. Repeat steps 2 – 4 for the remaining shelves.Note: one shelf in the locker must be level with the lock on the













NOTE: Masonry Hardware NOT IncludedREQUIRED HARDWARE:








THANK yOU for purchasing a Coleman product. Please give us a call, or visit us online if you have any other questions

or comments.




24 GAGE STEEl RTA TOOl CABINET


CABINET SHOUlD BE mOUNTED TO WAll TO AvOID INjURy







Capacity (lbs)

Overall Weight

Capacity

Locker 50 200

Wall 40 80

Base 50 150

Tool 30 150


PARTS AND HARDWARE SUPPlIED WITH BASE CABINET:QTy ITEm ImAGE1 Locking Rod

47 M5 Frame Screw

47 M5 Frame Nut

4 Adjustable Leg

16 M8 Leg Screws

16 M8 Leg Screw Nut

18 M8 Large Washer

16 Lock Washers

2 2.5” Wall Screw

4 5/8” Wood Screw


A

A

B

Z

Z

Y

Y

W

W

B

C

C

D

G

G Drawer Components

G

G

G

x3

E

E

F

F

D

X

X

Install InstructIons24 GAGE STEEl RTA TOOl CABINET

Top Panel

Left Back Panel

Bottom Panel

Drawer Front Panel

Drawer Back Drawer Bottom

Support Panel forDrawer Front

Right Back Panel

Left PanelRight Panel

Drawer


AB

C

D

E

F

E

FE

F

G



2. Assemble the left and right side panel with the same screw and nut. D Goes on the outside of A, and C goes on the outside of B.

3. Panel E sits on the outside of A and B, and on the inside of C and D. Do the same for panel F.


6. To install drawers, line up runners on the side of the drawer with the track on the inside of the cabinet and guide it into place.

5. Turn the cabinet back upwards and assemble drawers. See drawn assembly instructions on next page.




DRAWER ASSEmBly:1) Bend the two sides of DRAWER BOTTOM (Y) upwards to create

the side walls.

The Steel Metal Runners should be on the outside of the drawer.

2) Insert the edge of (Z) with 3 notches into the back of DRAWER BOTTOM (Y) using a mallet to wedge into place. Make sure all the notches at tops and sides of (Y) are snapped into notches on (Z).

**Below is what it will look like when Z has fit into the notches along the side and bottom of Y.

A

3. Insert the edge without the ridge of DRAWER PANEL (W) at the other side of DRAWER BOTTOM (Y). You may use a mallet to apply force. Note: Drawer bottom must rest on the inside of DRAWER PANEL (W).

4. Insert the SUPPORT PANEL (X) at the back of the DRAWER PANEL (W), be sure to insert this with the ridges edge upwards. Bang into place with a mallet. Once it passes the notches, it’s locked in.

Z Y

W X

ZY

W

X

Notch

Notch


ASSEmBly INSTRUCTIONS:CABINET lEvElING(for all cabinets except for wall cabinet)





NOTE: Base Cabinet Drawers must be removed prior to mounting Worktop.

• Pull each drawer out to full extension, simultaneously depress the left lock up and right lock down in each slider while pulling out the drawer. The drawer will slide out of the tracks ready to remove. See the diagram to note where the locks are on the drawer slides.





ENABlING lOCKING mECHANISm 1. Locate black vertical locking column attached to back-inside of

cabinet; this slides up and down. Push upwards to expose small hole.

2. Locate Locking Rod, and insert the tip of the bent end into hole in locking column at back of cabinet.

3. Locate the locking device at the top-inside of tool cabinet, and locate the thin slit between the locking device. Remove the pin attached to the cabinet lock, and set aside. Do not discard. Using the other end of the Lock Rod with a hole through it, align this with the lock hole.

4. Once holes are aligned, insert the pin through both to lock into place, between lock slit.

5. Test the lock.

Locking device is now ready.


Pin






top and bottom of the backside of the cabinet. Note: the cabinet has a perforated strip of holes at the top and

bottom of the cabinet, the locker only has a perforated strip at the top of the cabinet.






NOTE: Masonry Hardware NOT Included

REQUIRED HARDWARE: • 2 ¼” x ¼” Tapcon Concrete Anchor (4) 0r •#10 x 2” Screw with 3/16” masonry plug (4)







THANK yOU for your purchase! Please give us a call, or visit us online if you have any other questions

or comments.




24 GAGE STEEl RTA WAll CABINET








Capacity (lbs)

Overall Weight

Capacity

Locker 50 200

Wall 40 80

Base 50 150



PARTS AND HARDWARE SUPPlIED WITH WAll CABINET:QTy ITEm ImAGE4 Hinge

47 M5 Frame Screw

47 M5 Frame Nut

4 2.5” Wall Screw

4 Hinge Plastic Washer

4 Large Washer


BC

AD

EF

G

H

A B C D

E F G H

I

I

Top Panel

Left Back Panel

Right Door

Bottom Panel

Right Back Panel

Left Panel

Shelf

Right Panel

Left Door




E C

HI

F

D

A

B

G


2. Assemble the left and right side panels with the same screw and nut. D Goes on the outside of E, and C goes on the outside of F.

3. Panel A sits on the outside of E and F, and on the inside of C and D.

4. Put the four plastic washers in the holes at the four corners.

5. Insert the shelf. If shelf tabs are not catching with the inside of panels D and C, pull the shelf notches outwards.

6. Assemble the right and left doors and insert the hinges into the plastic washers to attach doors. Bend down the clips to fix the hinges in place. Extra spacers are provided to ensure doors are level.



ASSEmBly INSTRUCTIONS:INSTAllING SHElvES:

NOTE: Plan your shelf heights and install shelves starting from the bottom. The shelves are supported by the metal tabs on the back and side walls of the cabinet.


the diagram below.




5. Repeat steps 2 – 4 for the remaining shelves.Note: one shelf in the locker must be level with the lock on the













NOTE: Masonry Hardware NOT IncludedREQUIRED HARDWARE:





Install InstructIons24 GAGE STEEl RTA WAll CABINET


Install InstructIons24 GAGE STEEl RTA WAll CABINET




THANK yOU for purchasing a Coleman product. Please give us a call, or visit us online if you have any other questions

or comments.



24 gage steel rta locker cabinet install instructions...

Documents