2015 final the evolution of australian prison architectureeprints.brighton.ac.uk/14869/1/2015 final...
TRANSCRIPT
1
Finally Fit for Purpose: The Evolution of Australian Prison Architecture
Elizabeth Grant and Yvonne Jewkes
Introduction
Prisons tend to reflect the society that oversees them (Johnston, 2000). The
architecture and design of correctional facilities, as well as their regimes philosophies,
priorities and problems, are intrinsically related to their location. At their most
extreme, in a ‘Supermax’ (examples being the Florence Administrative Maximum
Penitentiary in Colorado, USA, or the High Risk Management Unit at Goulburn
Correctional Centre in New South Wales, Australia), prisoners may be held in
hermetically sealed environments which inflict, sometimes simultaneously, sensory
deprivation and sensory overload, resulting in psychic and physical pain on a par with
techniques of torture. At the other end of the penal spectrum (for example, in prisons
typically associated with Northern Europe and the countries of Scandinavia), prisons
seek to ‘normalize’ the prison environment with open-plan interiors, an absence of
hard fixtures and furnishings, maximum exploitation of natural light and access to
outside space. But what happens when one penal jurisdiction imitates the structural
designs of another with little regard for their political, social and cultural differences
and with no attempt to embrace the broader institutional philosophy or staff training
needs that underpin particular forms of penal design? This article traces the parallel
histories of the penal estates1 of the USA and Australia and illustrates that, from their
earliest days, the structure and internal layout of prisons became harmonized with the
enforcement of particular regimes, but that penal philosophies do not necessarily
travel with the architecture and design of prisons when transposed from one context to
another.
A brief history of prisons in the US and Australia
In their early incarnations, prisons in the US and Australia were similarly shaped by
the emergence of ‘Enlightenment thinking’ in Europe and by the views of prominent
prison reformers, including John Howard (1726-1790). Both countries ‘mined a
2
British tradition…for using the Gothic for prison structures’ (Johnston, 2000: 85); a
‘castellated mode’ that became established as ‘the style for prisons’ (ibid: 65-66).
They also followed the UK’s example of classifying inmates, holding them in separate
cells, subjecting them to discipline, hard labour and religious servitude and routinizing
their time; all of which were benignly viewed as the most effective means of
reforming criminals.
During the 1820s and 1830s the two contrasting methods of faith-based
reformatory prison regime that emerged in the United States and the UK, the
‘separate’ (or ‘Pennsylvania’) system and ‘silent’ system, sought to diminish the need
for physical punishment, as good behaviour was maintained ‘with the passive
instrument of the building itself’ (Nihill cited in Evans, 1982: 323). As a result, prison
accommodation became increasingly enclosed and cellularized and where previously
the architecture of incarceration had been based on Howard’s recommendations to
maximize ventilation and circulate air in the belief that these prevented physical
contagion, the architecture of the separate and silent systems was constructed around
the prevention of moral contagion – i.e. that prisoners risked becoming ‘worse’ if
allowed contact with other offenders.
Like their Anglo-American predecessors, the major, urban prisons built in
Australia2 in the 19th and early 20th centuries were dark, forbidding structures
surrounded by high, solid walls, which communicated a clear message about the perils
of crime, even to a population for whom the Gothic was hardly indigenous (Johnston,
2000). Internally, radial and cruciform designs were favoured, although there were
slight jurisdictional variations. For example, New South Wales prisons were
configured with detached wings radiating from a central chapel while in Queensland
wings were grouped around an open space. One or two major prisons were
idiosyncratic and did not employ typical architectural solutions. Often the
architectural designs constituted strange conglomerations or misinterpretations of
various concepts. For example, B Division at Pentridge Prison followed the
Pentonville doctrine for the design of the cell-block while the radial exercise yards
3
followed Philadelphia’s panoptic principles (Kerr, 1988). Fannie Bay Gaol in Darwin,
built in 1882, consisted of a cell-block and other more substantial buildings
surrounded by a series of galvanized iron structures. This was felt a suitable design
solution for the large number of Aboriginal prisoners held there, their perceived
security requirements, the location of the prison and the tropical climate.
In the 20th century rehabilitative thinking underpinned penal policy
throughout much of the English-speaking world, reaching a zenith in the 1950s, 1960s
and early 1970s when the welfarist model resulted in judicial proceedings being
influenced by a new raft of professional ‘experts’, including social workers,
psychologists, health professionals and academics. In the US, states including
California, Minnesota and Wisconsin rivalled countries such as the Netherlands and
Sweden for introducing rehabilitative programmes (Rothman 1980) although the
rhetoric was aspirational rather than grounded in reality and, as Haney (2008) notes,
even in their heyday, few prisons in the United States ever really functioned as fully-
fledged treatment or program-oriented facilities. The rehabilitation experiment was
also short-lived; by the mid-1970s ‘treatment’ was coming to be seen as further
expression of the state’s repressive disciplinary tendencies not least in relation to the
use of indeterminate sentencing whereby prisoners would be treated for as long as it
took to make them ‘better’. The now infamous 'nothing works' (Martinson, 1974)
paradigm that followed was intended by its liberal initiator to support a reduction in
the use of imprisonment. However, its appropriation by conservatives, who used
Martinson's findings to support their calls for longer sentences, more brutal regimes
and capital punishment resulted in many prisons in the US and Australia being starved
of funds for educational and other rehabilitative initiatives.
There essentially followed a long period when prisons became little more than
warehouses; a problem exacerbated by the dramatic rises in prison populations that
occurred from the mid-20th century (Mauer, 2001). President Nixon was elected on a
‘war on crime’ platform and initiatives such as the ‘Safe Streets Program’ (which
legislated preventative detention as a means to combat rising crime rates), the
4
establishment of agencies including the Law Enforcement Assistance Agency and the
National Institute of Corrections, and the deinstitutionalisation of the mental health
system were among the many factors that led to an increase and partial radicalization
of the prison population (ibid). As numbers grew it became dramatically clear that the
penal estate was not fit for purpose and the Bureau of Justice set about a definitive
program of change including, in 1971, the establishment of a multidisciplinary
research team composed of correctional administrators, architects, psychologists and
social scientists. The group visited over 100 correctional institutions across the United
States to observe and evaluate facilities and record the effects of the physical
environment on staff and prisoners (Johnston, 2000). Following their recommendation
that reintegration and rehabilitation should be the prime objective of corrections
(Nagel, 1973), the ideology of humane treatment was embraced by many US
correctional agencies and a program developing and applying evidence-based research
was formulated to move from punitive to rehabilitative models. Among the new
developments proposed was the introduction of unit management.
The mid to late-20th century was similarly characterized by rising prison
populations across Australia and the extension of human rights into prisons – or at
least the rhetoric of human rights, as some commentators have noted that in practice
little changed (Rynne, 2002). The pressures of post-war migration, population
increases and numerous government inquiries and Royal Commissions into issues
including poor conditions, assaults, brutality and discrimination against Aboriginal
prisoners, resulted in a sense of hopelessness at stemming the tide of problems and
there followed a prolonged period of neglect. The pressing need to update the
Australian penal estate was largely ignored and conditions deteriorated over several
decades. Many prisons lacked internal plumbing and prisoners used buckets for
sanitation; a number of facilities had no glass in windows resulting in prisoners
bearing the brunt of the (often extreme) weather (ibid). Even when new facilities were
built, the architects and planners got it badly wrong. For example, Risdon Prison in
Tasmania was commissioned in 1960 and designed by the Professor of Architecture at
5
the University of Melbourne, Brian B. Lewis. Curiously modelled on a Californian
prison, Risdon’s design was ‘totally inappropriate for the rigours of the Tasmanian
winter’, making it a particularly brutal and unpleasant prison for its occupants
(Ombudsman Tasmania, 2001).
As a result of such appalling conditions prisoner unrest was rife and the 1970s
witnessed a series of prisoner hunger strikes, roof-top protests and riots over poor
conditions and treatment. Brisbane’s Boggo Road Gaol, Western Australia’s
Fremantle Prison and South Australia’s Yatala Labour Prison all experienced
significant structural damage to the prison buildings as increasing numbers of
prisoners and bouts of prisoner disorder placed pressure on ageing infrastructures. An
urgent response was clearly required to address the appalling conditions and out-dated
operational policies and procedures and the New South Wales Nagle Royal
Commission constituted a watershed in Australian penal history, heralding a period of
significant, if brief, reform. The Commission’s final report, published in 1978,
revealed cultures of institutionalized violence against prisoners and recommended
over 250 changes to the penal system including the upgrade and replacement of
prisons and prisoner amenities. In turn, many Australian prison systems became the
subject of official inquiries regarding allegations of systemic abuse of prisoners and/or
conditions of confinement. The Governments of Victoria, New South Wales,
Queensland, Western Australia, South Australia and the Northern Territory all
embarked on comprehensive building programs to replace the older prisons and began
to implement ‘modern’ methods of prison management.
The decade that followed Nagle is commonly referred to as the ‘Golden Era’
of Australian Corrections because, after decades of neglect, attention was finally
given to rebuilding the dilapidated, Dickensian prison estate according to new
architectural concepts and developments emerging in the United States. Following
America’s lead, the Australian authorities enthusiastically embraced unit
management, secure perimeter barriers, campus planning, podular design, ‘new
generation’ or ‘third generation’ design, public private partnerships and the supermax,
6
but with mixed results. In the section that follows we will discuss each of these
architectural innovations and consider some of the difficulties in putting their
accompanying philosophies into practice in an Australian context
The Introduction of Unit Management
Unit management was first conceived in the US in the 1960s as a program delivery
system rather than architectural innovation. The first full prison implementation was
at Lewiston Penitentiary in Pennsylvania where ongoing violence had been a source
of concern and an inquiry suggested a trial of unit management (Ingram, 1978). Under
the trial, prisoners were divided into groups of approximately 100 individuals who
were housed around common living areas. Attached to each group was a unit
manager, a psychologist, one or two case managers, two or three correctional
counsellors and custodial officers. It was quickly identified that close contact between
staff and prisoners led to better delivery of programs, speedier problem identification
and the personalisation of services. The climate of the prison changed from one of
tension and violence to relative harmony and safety. Such was the commitment to unit
management that, by 1976, 21 of 31 institutions under the jurisdiction of the US
Bureau of Prisons were utilising the system in varying formats.
The unit management model quickly evolved and synthesized its program
delivery aims with the design of the environment. Underpinned by social
psychological theories of human relations and the symbiotic relationship between
buildings and behaviour, Robert Sommer’s theories of environmental psychology
were used to design prisons to complement and enhance the model. For example,
evidence-based research on privacy, territoriality, the behavioural impacts of noise
and visual connection with the outside world were applied to the design of unit
management settings in an attempt to ‘normalize’ the custodial environment and
address issues of human dignity and self-gratification (Sommer, 1974). Organization
and management perspectives were also applied to prison settings for the first time,
including emerging theories which argued that employees are capable of self-direction
7
and that managers can assist employees and prisoners to reach their potential, rather
than commanding and controlling them as subordinates. It was also suggested that
prison officers were likely to achieve greater work satisfaction through engaging with
prisoners than being deployed on activities such as manning towers and that prisoners
with access to meaningful lifestyle and personal development programs were less
likely to re-offend on release.
Other salient architectural and operational innovations to accompany unit
management included dispersing the dining and recreation activities to the living units
so that prisoners could, for example, make their own breakfast. Outdoor recreational
areas and libraries were included in designs. To lessen the prisoner violence
associated with shared amenities, cells were fitted with toilets, hand basins and in
some cases, showers. Cells began to be designed so as to afford an external view and
value was placed on providing natural light and ventilation to each cell. Each prison
was generally single-security category and prisoners were supervised by program staff
whose roles had replaced that of the guard or ‘turn-key’.
Some Australian jurisdictions viewed the developments in the United States
with considerable interest. Nagle’s (1973) recommendations that all New South Wales
prisons adopt unit management provided a powerful impetus for reform and in time
prisons across Australia were converted. Unfortunately, however, despite a broad
commitment to unit management’s organizational principles, its underpinning
philosophies were often ignored or misunderstood. The early conversions focused on
the classification of inmates and the need to accommodate prisoner sub-groups into
different units. The tiers of older prisons were filled in and areas sub-divided, creating
what is termed ‘second generation’ design in the US. In the sub-divided corridors of
cells, prisoners were supervised by ‘intermittent surveillance’ due to the facilities’
physical layout and the difficulties in the implementation of full supervision (unit
management being reliant on continuous observation which is not possible in a linear
setting). Nonetheless, across Australia, the gradual conversion of prisons to unit
management produced several benefits including immediately decreasing
8
disturbances, assaults and other problems relating to congregate activities. The
decreasing incidence of prisoner-on-prisoner assaults was anecdotally correlated to
retro-fitting of toilets into cells and the decommissioning of communal bathrooms.
There were, however, losses to prisoner amenities. Communal dining areas
were also often de-commissioned with prisoners left eating in cells or in the corridors
reassigned as ‘unit’ communal space. Recreational activities (such as concerts and
film nights) were no longer scheduled and in-cell television (when and if it became
available) grew to be the principle leisure activity for prisoners, leading to passivity,
lack of stimulation and erosion of social skills among many inmates (Jewkes, 2002).
In the Australian context, loss of communal eating and television viewing were
particular problems for Aboriginal prisoners who comprise 26% of the Australian
prison population (ABS, 2011) and make concerted efforts to control their social
groups and be imprisoned in the same correctional facilities in order to be close to
family and kin. The loss of prison association areas had a significant impact on these
groups who had previously used opportunities for communal activity as a source of
camaraderie and mutual support and to catch up on news of family and events,
providing respite from the ‘pains of imprisonment’ (Grant and Jewkes, 2013).
The Introduction of Podular Design and ‘New’ or ‘Third’ Generation
Philosophies
In the early 1970s, the US Federal Bureau of Prisons held a competition for the design
of inner city remand centres in four cities to house remand prisoners. Architects,
Harry Weese and Associates won the competition for the Chicago Metropolitan
Correctional Center with a design that aimed to provide humane living conditions in
urban environments where land was at a premium (Ichinowatari, 1979).
Commissioned in 1971, the 88 metre high triangular tower broke new ground in the
development of podular units and resolved issues arising from housing prisoners on
an inner city site by using a high rise model. Accommodation was designed within
right-angled triangular living units, with cells located around a communal space. The
9
triangular form decreased the internal distances to windows allowing all prisoners an
external view and reduced corridor lengths, minimising the distance to be patrolled.
In the decades that followed, a complex assemblage of factors resulting from
the introduction of a neo-populist political agenda (which included a ‘war on drugs’,
an unwillingness to afford prisoners any rights and the mass imprisonment of young,
black men from poor urban areas) resulted in continued unrest in many American
prisons. Research indicated possible reductions in prison violence through the
overlaying of podular design with unit management principles. Behaviour-based
evaluations were used for the assessment of design prototypes with US researchers
seeking to improve the fit between the physical setting and the organisational and
behavioural needs of user groups. By this time, mid-20th century discourses of
therapy and rehabilitation had given way to new ideas concerned with helping
prisoners to change and improve as a result of their own efforts, backed up by systems
of privileges or penalties to be administered for good or bad behaviour (Jewkes,
2002). Spatial organisation was instrumental in this respect, and the ‘new generation’
of prison architecture incorporated features of situational crime prevention into
design; for example, discrete housing units staffed by officers who operated
informally and interacted with inmates in living areas while having a clear sight of all
cell entrances.
This model of direct, informal supervision by officers – sometimes referred to
as dynamic security (Dunbar, 1985) – is aimed, not simply at aiding surveillance and
control, but also at facilitating communication between staff and inmates, so that the
role of officers is no longer to watch and respond to problems, but to predict and
prevent them. It was found that direct supervision by carefully selected and trained
staff was a crucial tool in reducing violence in prison settings and that linear design
should be avoided because it replicated ‘the streets’, where groups of prisoners
congregate to replicate some of the activities they might engage in on the outside.
Favoured design prototypes included personal podular spaces for prisoners positioned
around a shared interactive space; a concept that became known as ‘new’ or ‘third’
10
generation and quickly became the basis of contemporary penal design in the US
(Johnston, 2000).
The triangular podular design pioneered in Chicago and in the less
architecturally striking Metropolitan Correctional Centers in San Diego and New
York heavily influenced Australian prison design. The Government of South Australia
employed many of the concepts first seen in the Chicago Metropolitan Correctional
Center for the design of the Adelaide Remand Centre, commissioned in 1986, in the
belief that the specialist small units were a prime tool in managing the complex and
changing needs of sub-groups within the prison population. The Adelaide Remand
Centre incorporated an existing heritage-listed building for administration and
entrance functions, with a seven-storey addition at the rear containing eight living
units, indoor sports and recreation facilities (including a swimming pool), kitchen,
medical facilities and operational control facilities. A series of triangular forms reflect
the layout of the living units and overlook the exercise yards and inner city areas.
Communal bathrooms were relegated to history with the inclusion of in-cell
sanitation. The Adelaide Remand Centre stands as one of only two multi-storey
remand centres built within the central business district of an Australian capital city.
The other, Melbourne Metropolitan Remand Centre (later renamed the Melbourne
Assessment Prison when it became the reception prison for all male prisoners in
Victoria), was completed in 1989. Constructed of brick rather than concrete, the
design incorporated bands of cream on a red brick base to ‘heighten the humane
vision for the facility’ (Jackson Architecture u.d.). Both centres also followed the
American practice of locating remand centres in or near cities to allow detainees
greater access to family and legal services, minimize transport costs between courts
and reduce population pressure in prisons.
Following experiments with triangular shaped units, the blueprint was later
developed into a butterfly design of one or two storeys situated onto a central officers’
station. Nonetheless, some prisons constructed in the 1980s and 1990s retained a
model of uninspired linear living units with cells opening onto a central corridor,
11
reminiscent of the linear prison designs of the 19th century. In addition, although many
Australian correctional agencies aspired to direct supervision and case management,
there was considerable resistance by prison officers and their unions. Indirect
supervision (where officers monitor prisoners from enclosed posts) was favoured over
direct supervision or dynamic security due to perceived safety concerns. In essence,
Australia only adopted the physical model and not the program focus, the staff
profiles, the staff training models or the philosophies. It was not until the 1990s that
Western Australia introduced case management and prisoners received a sentence
plan (APP, 2012). Finally, at this stage jurisdictions began to formulate guidelines on
unit management specific to their circumstances.
The Introduction of Campus Planning
In the 1970s and 1980s in locations where space was not an issue, campus style
prisons were introduced which imitated architectural principles being applied in the
planning and construction of education and medical facilities. An early campus style
prison in the US was the Federal Butner Complex in North Carolina, commissioned in
1961 but not opened until 1976. Employing the campus principles of separated,
informally grouped buildings placed around communal external spaces, designers
sought to allow residents a sense of community and maximum freedom and space
inside the precinct. The emphasis was on holding residents responsible for making
constructive changes through voluntary program participation, minimizing tensions
between staff and prisoners and flexible decision-making. By the end of the 1970s,
other new facilities opened using the therapeutic principles of the campus model (but
not the clinical behavioural modification programs for which Butner became
infamous), incorporating open, campus planning and ‘third generation’ operational,
architectural and management approaches. Initial plans were predominately for low
security environments (e.g. Federal Correctional Institution Pleasanton, California,
commissioned in 1974) but, later, campus style planning was extended to the design
of medium and high security facilities. Following the US’s lead, campus style prisons
12
began to appear at the beginning of the 1980s in other countries, including Canada,
the UK and Germany (Fairweather, 1994).
Australia’s first campus style facility, Mobilong Prison, was commissioned in
1987. The prison is located on 50 hectares of land near Murray Bridge in South
Australia with an external perimeter fence enclosing approximately 15 hectares and
11,400 metre squares of building space. Mobilong was designed as an educational and
vocational training prison and the original workshops provided training in a variety of
skills and trades. It includes four ‘L’-shaped living units (albeit with cells laid out
with linear design adjoined to a communal space), separated by ‘village space’ from
operational support buildings. Since the commissioning of Mobilong, campus
principles have become integral to the planning of most Australian prison projects.
Post-occupancy evaluation has indicated particular design elements are imperative for
their success. These include zoning of areas, the separation of vehicular and
pedestrian routes and the provision of separate housing units, each with direct access
from cell to living areas (Home Office, 1985). To allow residents maximum space and
freedom of movement, security is ideally placed on the exterior of the site and the
location of the prison should be central on a large land holding creating a buffer zone,
where a perimeter fence is placed around the facilities (ibid). The land holding size
required for campus planning approaches is significant, and new prisons in Australia
are located greater distances from urban and regional centres than has been the
practice in the past, presenting obvious problems for prisoners to receive visits from
family and legal representatives.
The Development of Secure Perimeters
Returning to the United States, by 1990 the US Federal Bureau of Prisons was facing
a dramatic growth in prisoner populations and the increasing use of Life Without
Parole (LWOP), effectively creating a permanent prison population with nothing to
lose. A new discourse of ‘dangerousness’ and ‘risk’ had entered the carceral lexicon
and the American penal system, which had previously adopted a policy of
13
indeterminate sentencing coupled with parole release ‘as a matter of absolute routine
and good correctional practice’ (Petersilia, 2003: 62) had by now ceased even to
gesture in the direction of rehabilitation and reintegration and instead had explicitly
embraced a strategy of permanent exclusion (Dolovich, 2011). The convergence of
penal and medical discourses to assess the risk that any individual might pose and the
concomitant security measures required to predict and prevent any future harms they
might perpetrate had permeated down through the system so that it was no longer only
those offenders who presented a ‘vivid danger’ who were subjected to preventative
detention on grounds of prediction (Bottoms and Brownsword, 1982). Prison
managers even at the medium and low security end of the penal spectrum were
confronted with competing needs: the requirement to maintain security and control;
the desire to fully introduce prisoner unit management models of operation; and the
constraint of having to do both at a time when government policy did not allow
increases in staff numbers.
The solution to these problems appeared in the form of new technologies. A
perimeter security model was implemented based on the maxim ‘deter, detect, delay,
detain’ and enabled by new electronic systems and security technology adapted from
the military arena, including CCTV cameras. For example, each staffed guard post on
the ‘wall’ required four to five full-time armed staff if it was to be operational for 24
hours a day, 52 weeks a year, whereas electronic surveillance with a roving guard on
the exterior only required two full-time posts; one at the cameras and the other on
patrol (Krasnow, 1998). Another key feature of the new perimeters was the
construction of transparent, perforated fences which allowed roving staff to see
through them when called to a location where a prisoner might be contemplating or
attempting an escape. The perimeter was usually made up of a first fence with
detection equipment on the vertical plane, an inner ‘no-go zone’ with more detection
equipment and CCTV cameras, an outer fence, and then a patrol road, all illuminated
at night to an intensity to allow colour CCTV coverage. This system could consume
some 30 or more metres of perimeter width, a factor that required a large amount of
14
extra land, particularly when the authorities also wanted some distance from the patrol
road to the site boundary. A contentious aspect of the perimeters was that the tops of
the fences and, in high security centres, the inner area between fences, were installed
with rolls of razor wire. An argument for this extreme measure was that, with its
higher standard of containment, there could be a less restricted internal site, a factor
that supported the campus layout principles and operations.
Once again, Australia enthusiastically embraced these innovations and new
prison developments adopting the principles were built in remote rural areas. From the
mid 1980s, guard towers were consigned to history and the use of razor wire in prison
projects commenced (Knell, 2002), often in addition to a solid wall on the outer layer
of the perimeter. Unfortunately, in most Australian adaptations of the model, it was
determined that each zone required consideration to the type of monitoring and
controls and effectively prisons began to be conceived as a number of entities within a
perimeter or ‘prisons within a prison’, thus destroying features of the campus model
and returning the interior to something more akin to prisons in the UK. This appears
to have occurred in facilities where the operational pattern has returned to the control
model; where staff were not adequately experienced in people management; where the
prison is multi-security rated; and later, with the introduction of public private
partnerships, where the PPP model’s performance penalty system has created a
culture of risk avoidance rather than risk management.
As the sophistication of sensor and surveillance technology grew, Australian
prison authorities started to believe they could produce an escape-proof perimeter that
would allow them to do away with some of the original features, including the 24-
hour roving response team, replacing them with an on-demand model. Consequently,
detection equipment has functioned largely only as a means of alerting officers to an
incident already in progress. Staff are able to watch an escape unfold but can do little
about it. In addition, after a number of serious injuries and some fatalities, there is a
pressing requirement to construct a perimeter that is not physically harmful to
15
prisoners; again staff can do little but observe on a monitor when a serious injury or
fatality occurs due to an attempted abscondment.3
Arguably, then, the potentially humanitarian and rehabilitative elements of
unit management behind a secure perimeter have fallen dismally short in the
Australian context. Surveillance technologies have increased operational effectiveness
but at the expense of direct supervision and dynamic security. In what many would
come to see as a backward step, security and control became impersonal, rather than
interpersonal. At HM Barwon Prison, one factor in the choice of a solid perimeter was
bushfire risk but other arguably negative factors were instrumental, including
sequestering prisons from public gaze. More recent projects constructed in Victoria
include Port Philip Prison, the Metropolitan Remand Centre and the Hopkins
Correctional Centre (formerly Ararat prison) where expansion has been accompanied
by the construction of solid perimeters, which may have been chosen to allow their
security rating to be upgraded at a later date.
Penal Controversies: Public Private Partnerships and the ‘Supermax’
Before moving on to discuss Australia’s success in forging its own identity in
progressive penal design and construction, there are two particularly controversial
penal developments found in both the US and Australia that are worth brief
discussion. The first is privatization, which has become a cornerstone of corrections in
both countries and across the western world. The second is an architectural, political
and ideological statement which saw a reverse direction of influence as Australia
imported to the US what many prison scholars and penal reform groups consider to be
its cruellest and most unusual form of imprisonment – the Supermax.
The involvement of the private sector in the operation of prisons first emerged
in the 1970s, but really took off under the market-driven, New Right administration of
President Reagan in the 1980s. By 1990, two per cent of the US prison population
were housed in private prisons (Harding, 1992) and, since then, private prisons have
become a ubiquitous, if controversial, part of the American penal estate. According to
16
a report by the Justice Policy Institute (JPI), while the number of people held in all
prisons in the US has increased by 49.6 per cent over the past 15 years, private prison
populations have increased by 353.7 per cent (JPI, 2011). JPI’s allegation that private
prison companies have not only benefitted from this increased incarceration, but have
helped fuel it, may be strengthened by their finding that in 2010 alone, the Corrections
Corporation of America (CCA) and the GEO Group, the two largest private prison
companies in the States, had combined revenues of $2.9 billion.
Australia was the second country after the US to initiate Public Private
Partnerships (PPPs). The first private Australian prison was commissioned in 1988
when the Queensland Government awarded the contract for a new prison at Borallon
(Brown, 1992). Since then, PPP contracts have been awarded in Queensland, New
South Wales, Victoria, Western Australia and the Northern Territory and there are
currently eight private prisons holding 19.2% of the total Australian prison population
(Australian Productivity Commission 2012). The introduction of PPPs has had a
profound effect on procurement, design, construction and operational practices for
prisons and indeed the whole correctional landscape in Australia. While there are
varying preferences for procurement models around Australia, the level and
complexity of knowledge necessary to participate in the PPP process has resulted in a
number of architectural firms specialising almost exclusively in the design of
custodial environments. However, it has also led to some interesting and, in some
instances, compromised designs. For example, Deer Park Metropolitan Women’s
Correctional Centre (later renamed the Dame Phyllis Frost Centre) in Victoria has
faced criticism regarding the design and build quality, while Port Phillip Prison (also
in Victoria) experienced a number of deaths in custody, due in part to design issues,
which ultimately led to a review of the safety of cell environments across that State
(Coroner of Victoria 1999). It has been suggested that PPP projects by their nature
(they are subject to a fiscal penalty regime for performance failures) stifle innovation
and diminish the role of the architect, resulting in prescriptive design and operational
briefs (Consoli, 2004). While a number of commentators argue that PPPs have
17
improved Australian corrections in areas such as diversity in the prison estate, service
delivery and cost effectiveness (Harding, 1992), actual debate on the impact of PPPs
on prison design has been minimal. Unlike the US4, Australia does not have an active
movement among the design profession to boycott prison projects on the grounds that
involvement of the private sector leads to economically-driven rather than design-
driven projects. It would appear, then, that although PPPs were heralded as potential
vehicles for innovation, in Australia they have increasingly generated conservative
and limiting prison design.
Few architectural plans can be as conservative and limiting as the highest
security institutions, however. Australia’s vast expanses of uninhabited land and its
enthusiastic adoption of key architectural and technological features such as zoning
and electronically monitored perimeter walls may help to explain the Australian
super-maximum security prison; a concept that has not been embraced anywhere in
Europe. Although the supermax has its origins in the harsh conditions of solitary
confinement found in the ‘separate systems’ of mid-19th century prisons, its
philosophies were honed in the post-war era of behavioural psychology and
‘treatment’ when various forms of sensory deprivation and social isolation were
introduced in order to make prisoners susceptible to ‘remoulding’ through therapy and
medication. In more recent times, a punitive publicly-endorsed (or at least tolerated)
desire to make imprisonment rigorous and unpleasant may have accompanied a
sustained period of impatience with the criminal justice process which is frequently
characterized by media as ‘soft on crime’ (Johnston, 2000; Jewkes, 2011). New
prisons are being built with ‘a level of security above “high security”’ and internal
routines not seen for 140 years (Johnston, 2000: 4). Moreover, the ratcheting up of
security within penal systems in the US, Australia and many other western, industrial
nations, has run parallel to it escalation in a post 9/11, risk-attuned and retributive
society, rising to a level of prominence that eclipses every other consideration,
including what it means to be human (Drake, 2012). While this is true even of many
medium security prisons, it is particularly apt in relation to facilities such as the
18
Florence Administrative Maximum Penitentiary (ADX or Ad-Max) in Colorado, or
the High Risk Management Unit at Goulburn Correctional Centre in New South
Wales.
The first supermax is the subject of contention. Ward and Breed (1986) assert
that Alcatraz was the original supermax, while King suggests that this dubious honour
goes to the US Penitentiary at Marion, Illinois in the lockdown period following the
killing of two prison officers in October 1983. However, as Carlton (2009) has
observed, Katingal Special Security Unit in New South Wales, Australia, was a
supermax experiment that can be dated as far back as the 1970s. At Katingal every
aspect of a prisoner’s life was subject to staff control:
All doors were electronically operated by prison officers from behind bars that
separated them from prisoner areas. Prison officers also controlled the air-
conditioning and water temperatures, prisoner lights and power from remote
console panels. An air-conditioning system catered for the fact that there were
no windows in the tiny cells and the limited space in the exercise yards was
covered by steel mesh. The cells were so identical, so uniform the Department
found it necessary to paint the control panel in each gallery a different colour
so the officer in charge would not be disoriented (Carlton, 2007: 6).
While Katingal lasted barely two years before it was closed down because the
conditions of sensory deprivation for its inmates were considered an abuse of human
rights, Australia has retained the supermax security principles more commonly
associated with the United States. Political agendas in the 1990s were ‘quite literally
to intensify the punitive force of the experience of imprisonment’ (Brown and Wilkie,
2002), leading to a proliferation of supermax prisons, built to house the most
dangerous prisoners and those charged with terrorist offences. Goulburn, together
with several other New South Wales prisons, have been criticized over the lack of
natural light and airflow, isolation, deprivation of association, harsh environments and
regimes (NSW Ombudsman, 2008).
19
Australian Approaches to Prison Design in the Twenty-first Century
As the fallacy of uncritically following the United States’ example in penal design
became apparent, several national bodies were established in Australia, such as the
Corrective Services Ministers' Council and the National Correctional Administrators’
Council, to discuss and exchange ideas. National standards and guidelines5 were
finally initiated and, although drawing heavily on the US experiences in the first
instance, they were later tailored to local circumstances. Involvement in building
programs to upgrade the prison estate and other custodial facilities resulted in a
growth of expertise in prison construction within the Australian design professions
and correctional agencies and less reliance on overseas expertise.
The landscape of Australian corrections has now changed to the extent that
there are specific Australian approaches to contemporary prison design. Vernacular
forms and solutions have emerged to meet local imperatives such as prisoner needs,
budgets and political agendas. Every Australian jurisdiction has developed facilities to
accommodate minimum, medium and maximum security prisoners although, it must
be said, with mixed success. A positive example has been set by the State of Victoria,
which has developed several assessment and distribution prisons along the lines of
podular design and unit management as well as a number of prisons specifically built
to provide therapeutic, drug-free and treatment environments for particular groups of
prisoners (such as HIV positive and intellectually disabled prisoners, those with
substance misuse issues, women, sex offenders etc). New South Wales’ preoccupation
with control and security has in recent times changed to a focus on developing prison
environments to meet the needs of separate prisoner groups in a similar fashion to
Victoria. In Western Australia the overrepresentation of Aboriginal people in the
prison system has led to an emphasis on the development of specific facilities for
Aboriginal prisoners and attempts to house people near their families (Grant, 2009).
One notable success in this respect is the willingness of the Department of Corrective
Service, Western Australia, to embrace a regional approach with normalized living
conditions for Aboriginal prisoners. The recently opened West Kimberley Prison
20
accommodates 120 male and 30 female prisoners of varying security classifications,
in separate areas for men and women. Accommodation is provided in self-care
housing units, arranged so that prisoners can be housed according to family ties or
language, and security ratings. The units are located around an AFL football oval, the
sport being an important aspect of contemporary Aboriginal cultural identity. The
Northern Territory also grapples with accommodating high numbers of Aboriginal
people and is attempting to develop appropriate facilities for different groups of
offenders. Less imaginatively, Queensland has adopted a ‘one size fits all’ approach
with podular designs and sparse fittings to keep within set budgets and reflect
relatively punitive political agendas. Tasmania has been faced with the complexities
of accommodating differing groups requiring separate management styles within a
small system. In response, a single multi-purpose prison has been constructed to
accommodate the majority of prisoners. With stark finishes such as unpainted
concrete and harsh lines, it is reminiscent of Queensland’s approach to prison design.
As well as developing diverse approaches to address specific needs, Australia
has become an international leader in key areas of prison design, such as safe cell
technology. The ‘safe cell’ projects occurred after a coronial inquiry (1999) was held
into a series of deaths at Port Phillip Prison in Victoria. Design guidelines were
developed incorporating numerous prisoner safety components from evacuation in the
event of fire to the removal of obvious hanging points in mainstream cells
(Department of Justice, 2003). Correctional agencies in other states came under
pressure to examine the incidence of suicide and to employ similar standards and
ultimately Western Australia, South Australia and the Australian Capital Territory
developed their own design guidelines to reduce ligature points. Australia is also
progressive in the design of women’s facilities, borrowing some elements of the
Canadian experience and applying them within a local context. The predominant trend
is a move away from traditional cellular design, towards communities of cottage style
accommodation units overlaid onto campus plans. Dillwynia Correctional Centre in
New South Wales (commissioned in 2004) was the first to be designed with a campus
21
planning approach and domestic-style living units for prisoners, and was followed by
the Jacaranda Pre-release Units at Emu Plains, NSW. Other jurisdictions have
followed this lead and ‘women specific’ facilities with domestic style architecture
have been opened at the Brisbane Women’s Correctional Centre, the Mary Hutchison
Women’s Prison (Tasmania), Tarrengower (Victoria), and the AMC (Australian
Capital Territory). In 2009, the Bandyup Women’s Prison (Western Australia) was
also upgraded, having been designed and built to provide facilities and routines that
replicate (as near as possible) family and community responsibilities. The most
commonly cited example of ‘best practice’ design for female prisoners in Australia is
the Boronia Pre-Release Centre in Western Australia where architects were asked (in
2004) to design a prison that respected the unique characteristics of women. The
centre includes twelve houses for 70 residents and incorporates two mother and child
units, immediate care units, visits areas, children’s play areas, health centre,
administration areas, a spiritual area, medical centre and vocational training area; all
located within a landscaped environment.
Conclusion
As Johnston notes in the Introduction to his classic work Forms of Constraint: A
History of Prison Architecture, most histories of punishment barely mention the
buildings where confinement takes place, resulting in a ‘dismal’ and ‘disappointing’
understanding of their importance (Johnston, 2000: 1). He further observes that the
history of prison design and construction has not been linear, but has ‘cycles, bursts of
creativity and innovation as well as periods of stagnation and the continuation of
traditional planning’ (ibid: 2). As we hope to have shown in this article, Australia has
in recent years been enjoying a period of creativity following decades of conservative
traditionalism interspersed with eras of neglect and stagnation. There are still
challenges for Australian prison design, however. The innovative evidence-based
research into prison architecture and programs conducted in the US dramatically
changed prisons in Australia but demonstrate the importance of ongoing evaluation
and analysis of the local context. Many of the principles imported from the US were
22
only partially embraced and some of their potential benefits have been lost; for
example, when attention was not paid to the normalization of the environment or
where there have been increases in prisoner numbers without appropriate staff-
prisoner ratios being maintained.
The introduction of unit management and ‘third generation’ principles came at
a critical reform period in Australian corrections and framed the future direction of
Australian prison design, but the inspiration drawn from the US during the reform
period remained largely uncritical emulation. Australian jurisdictions could not
readily distinguish between the keenly promoted models coming out of the States,
tending to borrow parts but rarely implementing a holistic package of architecture,
management philosophy and staff training programs. This led to curious
amalgamations of mismatched design and policy, resulting in unmanageable prisons,
diminishing staff morale and aggrieved prisoners who frequently either fatalistically
resigned themselves to the psychological harms that poorly designed environments
elicit, or resorted to violence and disorder to vent their frustrations.
Nonetheless, Australian state penal systems have, in very recent years, made
significant advances both in applying US principles appropriately within a different
cultural context and, arguably more importantly, in finding their own identity and
accommodating prisoner populations in culturally sensitive and program-oriented
institutions. After more than a century of looking to the US and slavishly following
American design types, then, Australia is finally constructing a prison estate that is fit
for purpose.
Bibliography Australian Bureau of Statistics (ABS) (2011) 4517.0 - Prisoners in Australia, 2011,
Canberra, Commonwealth of Australia. Australian Prisons Project (APP) (2012) Key Moments in Penal Culture in Western
Australia 1970 – present, www.app.unsw.edu.au. Accessed 8th January 2015. Australian Productivity Commission (2012) Report on Government Services 2011:
Corrective Services. Canberra, Commonwealth of Australia.
23
Bottoms, A. E. and Brownsword, R. (1982) ‘Incapacitation and "Vivid Danger"’, in A. von Hirsch, A. Ashworth, and J. Roberts (eds.) Principled Sentencing: Readings on Theory and Policy, Portland OR: Hart Publishing.
Brown, A. (1992) ‘Prison Privatisation: The Queensland Experience’, in D. Biles and J. Verno (eds.) Proceedings of a Conference into the Private Sector and Community Involvement in the Criminal Justice System, Wellington, AIC.
Brown, D. and M. Wilkie (2002) Prisoners as Citzens: Human Rights in Australian Prisons. Sydney, The Federation Press.
Carlton, B. (2007) Imprisoning resistance: life and death in an Australian supermax. Sydney, Institute of Criminology Press.
Consoli, G. (2006) ‘The Architect’s Dilemma: A Self Reflection in Understanding Prison Design and Construction in Private Prison Projects’, Australian Journal of Construction Economics and Building 6 (2): 1.
Coroner of Victoria (1999) Coronial Inquiry, Death in Custody at Port Phillip Prison 1999. Melbourne, State of Victoria.
Department of Justice Victoria (2003) Cell and Fire Safety Guidelines (draft). Melbourne, Department of Justice, Victoria.
Dolovich, S. (2011) ‘Creating the permanent prisoner’, in C. J. Ogletree and A. Sarat (eds.) Life Without Parole: America’s New Death Penalty, New York: NYU Press.
Drake, D. (2012) Prisons, Punishment and the Pursuit of Security, Basingstoke: Palgrave.
Dunbar, I. 1985, A Sense of Direction, Home Office, London. Evans, R. (1982) The Fabrication of Virtue, English Prison Architecture, 1750 -
1840. Cambridge, Cambridge University Press. Fairweather, L. (1994) ‘Prison Design in the 20th Century’, in I. Spens (ed)
Architecture of Incarceration, London, Academy Editions. Grant, E. (2009) ‘Prison Environments for Australian Aboriginal Prisoners: A South
Australian Case Study’, Australian Indigenous Law Review 12 (2): 66 – 80. Grant, E. and Jewkes, Y. (2013) ‘More Important than Guns or Grog: the Role of
Television on the Health and Wellbeing of Australian Aboriginal Prisoners’, Current Issues in Criminal Justice (forthcoming)
Haney, C. (2008) ‘Counting Casualties in the War on Prisoners’, University of San Francisco Law Review 43: 93.
Harding, R. (1992) ‘Prison Privatisation in Australia: A Glimpse of the Future’, Current Issues in Criminal Justice 4 (1): 9-27.
Home Office (1985) New Direction in Prison Design: Report of a Home Office Study of New Generation Prisons in the USA. London, Her Majesty's Stationery Office
Ichinowatari, K. (1979) ‘Harry Weese: Humanism and Traditon’, Process Architecture 11.
24
Ingram, G. (1978) ‘Butner: A Reality’ Federal Probation 42. Jackson Architecture. (u.d.) ‘Project Sheet Melbourne Assessment Centre’
www.jacksonarchitecture.com Accessed 20th October, 2014. Jewkes, Y. (2011) Media and Crime, London: Sage Jewkes, Y. (2002) Captive Audience: Media, Masculinity and Power in Prisons. Devon: Willan. Johnston, N. (2000) Forms of Constraint: A History of Prison Architecture,
Champaign, IL: University of Illinois Press Justice Policy Institute (JPI) (2011) Gaming the System: How the Political Strategies
of Private Prison Companies Promote Ineffective Incarceration Policies. http://www.justicepolicy.org/uploads/justicepolicy/documents/gaming_the_system.pdf Accessed 18th March, 2014.
Kerr, J. S. (1988) Out of Sight, Out of Mind: Australia's Places of Confinement, 1788-1988. Melbourne, National Trust of Australia (NSW).
King, R. (2007) ‘Security, Control and the Problems of Containment’ in Y. Jewkes (ed.) Handbook on Prisons. Devon: Willan.
Krasnow, P. (1998) Correctional Facility Design and Detailing, New York: McGraw-Hill
Knell, A. (2002) The Devil's Rope: A Cultural History of Barbed Wire, London: Reaktion.
Martinson, R. (1974) ‘What Works? Questions and Answers about Prison Reform’, The Public Interest, Spring, 22-54.
Mauer, M. (2001) ‘The Causes and Consequences of Prison Growth in the United States’ Punishment and Society, 3(1): 9-20.
Nagel, W. (1973) The New Red Barn: A Critical Look at the Modern American Prison. New York, American Foundation, Institute of Corrections/Walker.
NSW Ombudsman (2008) NSW Ombudsman's Annual Report 2007-2008. Sydney, NSW Ombudsman.
Office of the Ombudsman (2011) Report of an Inquiry into Risdon Prison. Hobart, Office of the Ombudsman, Tasmania.
Petersilia, J. (2003) When Prisoners Come Home: Parole and Prisoner Reentry, New York: Oxford University Press.
Rothman (1980) Conscience and Convenience: The Asylum and its Alternatives in Progressive America. Boston: Little, Brown.
Rynne, J. (2002) ‘Protection of Prisoners’ Rights in Australian Private Prisons’, in D. Brown and M. Wilkie (eds.) Prisoners as Citizens: Human Rights in Australian Prisons, Sydney, Federation Press: 131 - 152.
Sommer, R. (1974) Tight Spaces : Hard Architecture and how to Humanize it. Englewood Cliffs, N.J., Prentice-Hall.
25
Ward, D. and Breed, A. (1986) The United States Penitentiary, Marion Illinois: A Report to the Judiciary Committee, U.S. House of Representatives, 99th Cong., 1st Sess., 1985.
Author Biographies Dr Elizabeth Grant is a senior academic at the University of Adelaide, Australia. An architect and anthropoligist, Dr Grant is an international expert on the design of Indigenous custodial environments and has published extensively on Australian prisons. Professor Yvonne Jewkes is Professor of Criminology at the University of Leicester. She has published extenisibley on prisons, the sociology of imprisonment, prison design and prison culture.
1 We use the term ‘penal estate(s)’ throughout the article. Although possibly less familiar to a US readership than to readers in the UK, Australia and elsewhere, it most satisfactorily encapsulates the physical, structural dimensions and interior, environmental features of both individual facilities and the system as a whole. 2 Broadly speaking, Australian prisons have fallen into two categories; major prisons – typically large and imposing, emulating the English archetypes of the mid-nineteenth century – situated on the fringes of densely populated urban locations (e.g. capital cities) and holding serious offenders; and local prisons, equivalent to US jails, which are typically low-rise, sprawling constructions situated in rural environments, and holding prisoners serving shorter sentences for minor offences. 3 A notable exception has been the design of juvenile and mental health facilities. Some jurisdictions will not allow the use of any materials that could cause physical harm to anyone attempting to escape. 4 In the US Architects/Designers/Planners for Social Responsibility (ADPSR) has called for a boycott of all prison design and construction on the grounds that the prison system is ‘a devastating moral blight’ which ‘has no place in a society that aspires to liberty, justice, and equality for all (http://www.adpsr.org/home) 5 The Standard Guidelines for Prison Facilities in Australia and New Zealand (1990) is a set of design guidelines for the construction of new prisons, while the Australasian Correctional Planning Framework (2000) expands on the requirement of the Building Code of Australia. The Revised Standard Guidelines for Corrections in Australia (2004) is a set of minimum standards for prisoner treatment and conditions. These are not enshrined in legislation.