Welcome to the Martin Archery Family. We are confident thatyou will experience many years of enjoyment from your new Martinbow. Each bow that leaves our door is handmade one at a time as theyhave been for fifty years. Martin Archery remains a family owned andoperated business. We take great pride in every product we produce andwe strive to offer you the most complete line of professional accessoriesavailable.

We welcome any comments you may have about our products.We also like to hear stories of your successes while using our products. Ifyou have any comments, photos, or information you would like to sharewith us, please call or write. We will do our best to answer any questionsyou may have.

To better serve you, we have the most complete archery manu-facturers Web page on the World Wide Web. Our home page includes ahot link directly to our E-Mail box so you can keep in touch with us.Our Web page is located at: www.martinarchery.comOur E-Mail address is: info@martinarchery.com

Thank You,

Gail MartinFounder and PresidentMartin Archery Inc.

2

TABLE OF CONTENTS

3

OWNERS RECORD ......................................................................................... 4

PARTS OF THE BOW ..................................................................................... 5

BASIC SETUP Cable Guard Installation ..................................................... 6 Setting Draw Length ........................................................... 6 Changing Draw Weight ....................................................... 7 Setting Tiller ........................................................................ 7 Wheel Timing (For Two Cam Systems) ............................... 8 Setting Arrow Rest Position................................................. 9 Setting Nock Point ............................................................... 9 Replacing Strings ................................................................ 9 Care and Storage ................................................................. 9

THE FURY CAM & FURY X Getting Peak Performance ................................................... 12 Cam Positioning .................................................................. 12

THE FUZION SINGLE CAM SYSTEM Adjusting Draw Length ....................................................... 10 Setting Tiller ........................................................................ 11 String Configuration ........................................................... 11

THE Z CAM Setting Draw Length ........................................................... 6 Changing draw weight ........................................................ 7 Setting Tiller ........................................................................ 7

FINE TUNING YOUR COMPOUND BOW Bare Shaft Planing Test ....................................................... 13-14 Paper Tuning ....................................................................... 15-17

SUPER FINE TUNING Short Range Group Tuning ................................................. 18 Flight Tuning Broadheads ................................................... 19

TEN COMMANDMENTS OF ARCHERY SAFETY ........................ 20

FREQUENTLY ASKED QUESTIONS .................................................... 21

MARTIN WARRANTY ................................................................................... 22

4OWNER'S RECORD

NOTICE:Staple your sales receipt here

Proof of purchase date is needed should you ever require warranty work

BOW MODEL: ________________________________

LIMB TYPE: ________________________________

CAM: ________________________________

DRAW WEIGHT: ________________________________

DRAW LENGTH: ________________________________

STRING LENGTH: ________________________________

PURCHASED FROM: ________________________________

DATE: ________________________________

5PARTS OF THE BOW

Limb Pocket

Upper Limb

Idler WheelAxle

Shooting String

Limb Bolt

Riser

Slide Slot RestMounting Hole

Grip

Lower Limb

Fuzion Cam

Split String

Cable Guard

Stabilizer Insert

(Cougar with Fuzion Cam System)

Lock MountRest MountingSystem

Barrel NutQuiver Mounts

Your new Martin bow takes little setup to get started shooting. Please readand familiarize yourself with these starting procedures before shooting. Manyof these procedures will have been completed by your authorized Martin dealer.After completing these simple steps, you will be more accurate and will havegreater success from the start. A careful and thorough initial setup will makethe tuning process much easier.

6

CABLE GUARD INSTALLATIONAll Martin compound bow models* feature smooth

bore holes in the riser that allow direct, bracket-freeinstallation of the cable guard rod. There are set screwswithin the riser that will secure the rod.

The cable guard rod should be rotated toward the grip toprovide adequate fletching clearance. Caution should betaken against over-rotating the rod as excessive clearancecan cause unnecessary pressures on the limb tips and axlebushings. Only 9/16 offset is necessary to provideadequate fletching clearance.

Though most bow models allow either an upper (abovethe arrow rest) or lower (below the grip) mounting, MartinArchery recommends the upper mounting position on allFuzion single cam models.

*As of this writing, the Scepter II and Rage models didnot allow the direct installation of a cable guard rod. Amounting bracket is supplied with these models that threadsinto the threaded holes provided in the back of the riser.

SETTING DRAW LENGTHZ Cams and Mini Z Cams

The Z Cam uses draw length modules to adjust thedraw length. The size of each module is designated by anumber followed by an 'X'. These modules are sized from2X to 9X. The 9X makes the longest draw and the lengthdecreases one inch for each number. To change the drawlength on these cams, simply remove the two screwsholding the module to the cam. Take a look at the modulenumber and select a new module that will give you thecorrect draw length. Install the new modules, making surethat the numbers on each module match.NOTE: Do not draw your bow without the modules installed.It will cause damage to your harness system.

CableGuard

BASIC SETUP

7Fury Cams & Fury XThe Fury Cam is a draw length specific cam. Each cam was designed to give peak

performance and speed at each specific draw length. Therefore, changing the drawlength requires changing to a different size cam.

Fuzion Single Cam SystemA full explanation on the Fuzion Cam System, including changing the draw length,

can be found on page 10 and 11.

CHANGING DRAW WEIGHTMartin bows have a fifteen pound draw weight range. Using the 3/16 Allen wrench

supplied with each bow, you will turn the limb bolts clockwise to add weight and turncounter clockwise to reduce weight. One complete turn on each limb bolt providesabout 4 pounds of adjustment.TIP: Mark a line on each limb bolt in white-out or white paint marker to make it easierto keep track of how far you are turning each bolt.NOTE: Do not shoot your bow with the limb bolts more than 5 turns out from the riser.

SETTING TILLERAfter setting the draw weight on your bow, you will need

to set the tiller measurement to make sure that you haveadjusted your limbs properly. On all Martin compound bows,0 tiller will shoot perfectly. However, the tillermeasurement can vary up to 1/4 closer at the bottom.There is no set measurement that provides peak perfor-mance for every shooter. To measure your tiller, simplymeasure from the limb pockets to the string on both endsof the bow (see Fig.1). You can custom fit the feel of yourbow by experimenting with the tiller setting. Start witheven tiller, when both top and bottom limbs are adjustedthe same. (Before adjusting your limb bolts, mark a whiteline from the center of the limb bolt to the outside. Thiswill help you keep track of your settings.) By tighteningone bolt a quarter turn at a time you will begin to affectthe steadiness of your setup. If the bow begins to becomeunsteady, move the tiller back to even and tighten the op-posite limb bolt. After finding the best spot, make a note soif you ever change the draw weight you can reset the tunewhere you had it shooting best (i.e., 3/4 bottom wouldmean three quarters of a turn on the bottom limb bolt).NOTE: Your peep sight position and your nock point willchange as you turn one limb bolt. Take measurements andcorrect your nock and peep each time you turn your bolts.

Fig.1

8Cams are inperfect time.

Upper Cam isover-rotated andout of sync withthe bottom cam

Adjust this yokeby twisting up thebottom SplitString cable.

This procedure can be expertly performed by yourlocal archery professional. You will need a bow pressor a bow stringer to adjust your timing using the SplitString System. First, determine which cam is ahead,or out of sync. The Split Strings, or buss cables, shouldreach the end of the cable grooves on the Power Side(back side) of each cam at the same time. Then, whilethe bow is relaxed, remove the appropriate Split Stringoff its outside posts and twist in a direction thatshortens or tightens the cable. A few turns will go along way so proceed sparingly. If your top cam is ahead,or rotates further than your bottom cam, twist thebottom Split String, do the opposite if the bottom wheelis ahead. After these steps are completed make surethat all of your string loops are firmly secured on theirappropriate pegs before the pressure is reapplied tothe bow.

String Anchor

SplitString

Adjusting timing using the Split String System (synthetic cables)

WHEEL TIMING (FOR TWO CAM SYSTEMS)It is important for consistency and accuracy that your bows cams roll over at the

same instant and are in the same position when you are at full draw. Your camsshould be synchronized or timed to your particular style of shooting. To check thetiming, draw your bow with your fingers or release just as you would while shooting.Different drawing methods will affect the roll over of your cams. Draw the bow usingyour exact shooting method.

NOTE: Back your bow limbs out five turns from the riser before using a bow stringer ora bow press. Only let a qualified professional put your bow in a bow press.

9Bowstring

REPLACING THE STRINGSShould your string need replacing, it is best to go to your Martin dealer and have it

expertly done. It is recommended that you replace your string once a year or anytimeit shows wear. Always be sure that the string you replace it with is the correct lengthand material for your bow.

CARE AND STORAGEWhen properly cared for, your new Martin bow will give you years of

trouble-free service. When your bow is new it will require no lubrication. Over timeyou may need to lubricate your cams to guard against friction and noise. Use a drylubrication such as Teflon spray powder or graphite powder. Do not use wet or oilylubrication. Using a wet type lubrication will attract grit and dust that may causepremature wear in wheel bushings.

A good rule of thumb when caring for your bow is to keep it as comfortable as youare. If it is too hot for you, it is too hot for your bow. If it gets wet, dry it off completely.Periodically clean your bow with a wet rag and mild soap to remove mud or dust(caution: do not store until completely dry). Prolonged exposure toextreme heat may cause failure in your bow limbs and excessive stretch in yourharness system. It will not hurt your bow if it is rained on while shooting, but makesure it is completely dry before storing in a bow case to guard against rust orcorrosion.

1/21/4900

SETTING ARROW REST POSITIONAfter your arrow rest is installed on your bow, you will need

to set the rest to the best centered location to begin tuning. Theeasiest way to do this is to visually align the bowstring in thecenter of the grip section. If you are shooting your bow with arelease aid, the prongs or blade of your shoot-through rest willneed to be centered with the bow string. During tuning, yourarrow rest may need to be moved in or out from its centeredlocation. This is normal because different shooters applydifferent pressures to the bow. Finger shooters will need toposition the rest so that the point is about 1/8 outside the string.This is to compensate for the horizontal bending of the arrowupon release. An arrow rest that provides some side support,such as a cushion button, for the arrow is best for fingershooters.

SETTING NOCK POINTPlace a bow square on the string and slide the square down

until it rests on your arrow rest. Then place a moveable nock seton the string. Using the measuring scale on the bow square, setthe nock set at the proper location on the string. A goodstarting point for finger shooting is 1/4 high, measuring fromthe bottom of the nock set to 90 on the bow string. Start at high if you are using a release aid. If you do not have a bowsquare, you can snap an arrow on the string and visually levelthe arrow. Then crimp your nock set. In a pinch, this will getyou to a good starting location.

ADJUSTING THE DRAW LENGTHThe Fuzion Single Cam System boasts a

revolutionary design and is engineered to give youpeak performance and speed. Using draw lengthmodules, the draw length can be adjusted in 1"increments (see fig. 1) The modules can also be usedto adjust the let-off. A high let-off module is markedas F-#. A 65% let off module is marked with a F-#\.The slash on the end of the size number indicates65% let-off. To change the draw length replace themodule on the cam by removing the screws that holdit to the cam (see Fig.3). NOTE: do not draw yourbow without the module installed. It will damageyour harness. The Fuzion module sizes range fromF-1 to F-7. If you would like to increase the drawlength select a higher number. If you would like todecrease the draw length select a lower number. Thedraw length can also be adjusted up or down 1/2"

10

The Fuzion system is unique among all other single cam systems. The Fuzionsystem has a modular draw length adjustment that can be adjusted in half inch adjust-ments within each draw length module.

Fuzion Module#3054 F1 - F7

BP-6 modulescrews

Fuzion Cam#3050

Fig.3

Fig.1

THE FUZION SINGLE CAM SYSTEM

using the pegs on the back of the cam (see fig.1). The #2 peg is the prescribed drawlength for each module. The #1 peg is 1/2" longer and the #3 peg is 1/2" shorter. Thedraw weight will change one or two pound, accordingly, when using the peg adjust-ment.

11

STRING CONFIGURATIONThe string harness on the new Fuzion are installed according to the diagram below(see Fig.4). Your string harness should be installed by your qualified Martin dealer.

SplitString

ShootingString

Fig.4

SETTING THE TILLERYour Fuzion bow should start out with an even tiller setting. Even tiller, or "0"

tiller, makes sure both limb bolts are adjusted evenly. (see Fig.2)

Fig.2

12

GETTING PEAK PERFORMANCE The Fury Cam is designed to provide optimum performance when the draw weight

is at its maximum setting. In order to attain the top performance expected from thisCam system, it is strongly recommended that the draw weight be set at its maximum.This setting will also keep noise to a minimum and benefit accuracy.

CAM POSITIONINGIn order to achieve the ideal draw force curve and resulting maximum efficiency, the

Fury Cams need to be positioned properly. Though the exact cam position is notcritical, the straight section of the cam should be aligned vertically and parallel withthe bowstring (see diagram). No exact measurement is required, just a visual checkwill be sufficient. Should the bow string stretch abnormally, the straight section of thecam can rotate closer to the bowstring, increasing draw length and draw weight whileadversely affecting performance. Add twists to the bowstring to reduce its length andreturn the cam back to its proper alignment.

FURY X STRING CONFIGURATIONStrings: Use same string lengths as the standard Fury Cam system. You will need afour buss cables and one shooting string. Cables can be made with as few as 8 strandsof BCY 450+ or S-4 material. Shooting strings need the standard strand count.

THE FURY CAM & FURY X

Properorientationof string andCam point.

Proper campositioning asseen on thebow. Thispositioningapplies to anybow using theFury Cam.

ExistingCable Anchor

LargeCable Anchor

WhiteSpacer

BlackSpacer

After completing the basic setup procedures, you are now ready to fine tune yoursetup for the best accuracy possible. There are four tuning methods described in thissection. Some of these methods may not apply to certain styles of shooting. Read theintroduction to each method carefully to make sure it applies to your shooting style.

BARE SHAFT PLANING TESTThe Bare Shaft Planing method of tuning works best when using a finger release. To

begin the Bare Shaft Planing test you will need three fletched arrows and one or twobare shafts. You will also need a target that will catch the arrows without allowing thearrow to kick as it stops in the target. This test will help you establish the correct nockand rest position, and it will tell you if your arrow is the correct spine. Porpoising andFish Tailing describe the different flight disturbances you will encounter while tuning.

PorpoisingPorpoising is identified by an up and down kick during arrow flight and relates to

the nock point adjustment. It is important to correct porpoising first because small leftand right disturbances could be nock point related. Start at about ten to fifteen yardsand shoot three fletched arrows into your target. Using the same aiming point, followthem up with a bare shaft. After you get the shafts to impact with the fletched shafts,you may want to try shooting them at a longer distance for a finer indication of arrowflight.

If the bare shafts impact below the fletched arrows, your nock point is too high.Move your nocking point down in small increments until the bare shaft strikes with thefletched shafts. If the bare shafts impact above your fletched arrows, your nock point istoo low. Lower your nock point in small increments until your fletched arrows andyour bare shaft impact together.

Repeat the above steps from a longer distance to make sure you have completelycorrected the nock point. Shooting from a longer distance will make minordisturbances more apparent.

FINE TUNING YOUR COMPOUND BOW

A high nock set will cause porpoising

13High nocking pointLow nocking point

FishtailingFishtailing relates to the arrow rest adjustment and the stiffness of your

arrow. Just as before, start at about ten to fifteen yards and shoot three fletched arrowsinto your target. Using the same aiming point, follow them up with a bare shaft. Afteryou get the shafts to impact with the fletched shafts, you may want to try shooting themat a longer distance for a finer indication of arrow flight.

If your unfletched shafts impact to the left of your fletched shafts, your arrow is toostiff. There are several things that you can do to correct this problem; you can select aweaker arrow, you can decrease the cushion plunger tension. Increasing the peakweight of your bow or increasing your point weight will also make your arrow act abit more limber. If your unfletched shafts impact to the right of your fletched shafts,your arrow is too limber. There are several methods you can try that will correct thisproblem; you can select a stiffer arrow, you can increase the cushion plunger tension.Decreasing the peak weight of your bow or decreasing your point weight will alsomake your arrow act a bit more stiff.

To further fine tune your setup, step back to twenty or thirty yards and repeat theabove procedures. Small flight disturbances will show up better as you get fartherfrom the target. Your Martin bow is essentially tuned when your bare shafts hittogether with your fletched shafts. Keep in mind that if you continue and complete thesuper fine tuning methods in this manual, it is not uncommon for your bare shaftimpact to change. Your bow will be shooting its best and it is common for a perfectlytuned bow to shoot a bare shaft a bit low and right or low and left. Perfect arrowgroups are the goal when completing these exercises.

14

Left handed shooters should follow instructions in reverse.

Stiff Arrow- bareshafts fly to left.

Limber Arrow-bareshafts fly to right.

15

Paper tuning will work for all styles of shooting. As you are going through thesesteps keep in mind that paper tuning is not chiseled in stone as the law of archery. It isa guideline for clean arrow flight. Many shooters find that their setup groups bestwhen achieving less than perfect tuning results. For example, some target shooters settheir bows to tear slightly high through the paper. They feel this makes their arrowflight less likely to be influenced by outside variables like wind or rain and helps arrowclearance when using a shoot-around type rest such as a blade or pan type launcher.

To begin paper tuning, set up a frame or rack with paper suspended from the frame.Position the frame far enough away from your backstop so the arrow cancompletely clear the paper. Stand about ten feet from the paper and make sure yourarrow is level as it flies through the paper. Fire a test shot and read the results.Compare the holes you have made in the paper to the diagrams below. Procedures forcorrecting the tear are listed next to each diagram. Please note that tuningprocedures recommended for finger shooting often differ from those used forrelease shooting. You will find that the arrow spine reaction is different for fingers andrelease, therefore, the procedures for correcting the different disturbances vary.Follow the instructions carefully for your particular shooting style.

HIGH TEAR (fletching tears above point)This tear may signal: Nocking point too high.

Lower the nocking point. Improper vane clearance.

See if arrow fletching is hitting the rest. Launcher is too stiff (release shooters).

Weaken spring tension or use a more limber launcher. Wheels may be out of time.

Check wheel timing. Arrow may be too limber

Select a stiffer arrow shaft. Tiller adjustment may be incorrect.

See basic setup section page 7. Irregular or inconsistent shooting form.

See a qualified archery coach or professional and have them check your technique.

LOW TEAR (fletching tears below point)This tear may signal: Nocking point too low.

Raise the nocking point. Wheels may be out of time.

Check wheel timing. Tiller adjustment may be incorrect.

See basic setup section on page 7. Irregular or inconsistent shooting form.

See a qualified archery coach or professional and have them check your technique.

PAPER TUNING

RIGHT TEAR (fletching tears to the right of point)This tear may signal:Note: If you are left handed follow these instructions in reverse.

FINGERS: Stiff arrow.

This problem is cured using the following methods: a. Increase peak weight. b. Use a heavier point. c. Select a more limber arrow. d. Lighten cushion plunger tension, or use a weaker spring on shoot around rests. e. Make small incremental rest adjustments towards the bow.

RELEASE: Arrow rest is too far to the right.

Move arrow rest to the left.

EITHER STYLE: Too much pressure on the cable guard.

Rotate cable guard for minimum fletching clearance. Irregular or inconsistent shooting form.

See a qualified archery coach or professional and have them check your technique. Clearance problem.

See that arrow has adequate fletching clearance.

LEFT TEAR (fletching tears left of point)This tear may signal:Note: If you are left handed follow these instructions in reverse.

FINGERS: Weak arrow or a clearance problem.

This problem is cured using these methods: a. Reduce bow weight. b. Use a lighter point. c. Select a stiffer arrow. d. Increase cushion plunger tension or use a stiffer spring on shoot around rests. e. Make small incremental rest adjustments away from the bow .

RELEASE: Arrow rest is too far to the left.

Move the arrow rest to the right. Arrow is too stiff.

Decrease bow weight or select a weaker arrow.

EITHER STYLE: Arrow is not properly clearing cables.

Rotate cable guard for minimum fletching clearance. Irregular or inconsistent shooting form.

See a qualified archery coach or professional and have them check your technique. Clearance Problem.

See that arrow has adequate fletching clearance.

16

MULTIDIRECTIONAL TEARThis tear may signal: More than one problem with accessory adjustment.

Move nock adjustment first until the tear is horizontal and followinstructions for horizontal tear.

Clearance Problem.See that the arrow has adequate fletching clearance.

Wheels may be out of time.Check wheel timing.

Irregular or inconsistent shooting form.See a qualified archery coach or professional and have them check your technique.

17

PERFECT HOLEThis pattern shows clean arrow flight. The point and fletching

impacted the same location. Your bow is now ready to shoot or youmay want to continue and try some of the super fine tuning methods.

AFTER ADJUSTINGAfter you have completed these steps and have achieved good paper test

results, it is best to try it at fifteen and twenty feet just to make sure you did not get afalse reading. A good rule to go by when paper tuning is to move your nock point orarrow rest opposite the tear when using a release. In some rare cases if this does notclear up your tear you may need to move your accessories in the same direction as thetear.

SHORT RANGE GROUP TUNINGShort range group tuning will work with any style of shooting. Best results are

achieved when this method is used after completing the Bare Shaft Planing or PaperTuning tests. This is a good ultra fine tuning method when space will not permit longrange shooting. After completing the following steps you will have very clean arrowflight and a well tuned, accurate setup.

To begin the short range tuning method, you will need a piece of cardboard, or atarget face will do nicely. Make a broad line through the center of the paper on theblank side, making sure the line is thick enough to see from twenty yards. Start atabout 10 to 15 yards from the target. Use your tuning target and position the linevertically when you are tuning the arrow rest and position the line horizontally whenyou are tuning the nock point.

Vertical ImpactPosition your line horizontally and shoot six arrows at the line. Concentrate on

keeping your pin on the line. Dont worry about left and right hits, just try to keep yourshots on the line. Shoot two good groups, discarding any rough or bad shots, and notethe vertical impact of the arrows and their relationship to the line. All adjustments aremade with the nock point during these steps.

If your arrows are not consistently grouping on the line, make small 1/32"adjustments up or down with the nock point and shoot two more groups. Continuemaking nock adjustments in small increments. If all of your arrows begin to hit on theline you are correcting the nock position. In the event that your groups widen, moveyour nock back to its original location and make small adjustments in the oppositedirection.

Horizontal ImpactAfter achieving a nice, straight, horizontal pattern, rotate your target so your line

will appear vertical. Just as before, shoot two good groups, discarding any rough orbad shots, and note the horizontal impact of the arrows and their relationship to theline. All adjustments are made with the arrow rest during these steps.

If your arrows are not consistently grouping on the line, make small 1/32"adjustments left or right with the arrow rest and shoot two more groups. Continuemaking rest adjustments in small increments. If all of your arrows begin to hit on theline you are correcting the rest position. In the event that your groups widen move yourrest back to its original location and make small adjustments in the opposite direction.

SUPERFINE TUNING

This patternshows averticaldisturbance.

This patternshows a cleanverticalpattern.

This patternshows a

horizontaldisturbance.

This patternshows a clean

horizontalpattern.

18

19

Multidirectional FlightCorrect the nock point first.Once the arrow is straight left,follow instructions for left flight.

High FlightRaise nock point

Left FlightRelease:Move arrow rest tothe right in smallincrements.

Fingers: Slightly increase draw weight. Use a heavier broadhead. Decrease cushion plunger tension. Move plunger toward the bow in small increments.Reverse steps for left hand shooter.

Low FlightLower nock point

Right FlightRelease:

Move arrow rest to the left in

small increments

Fingers:Sightly decrease

draw weight.Use a lighter

broadhead.Increase cushion plunger tension.

Move plunger away from the bow in small increments.Reverse steps for left hand shooter.

Field Point Group

Broadhead Group

FLIGHT TUNING BROADHEADSBroadhead tuning will work for all styles of shooting. After you have completed one

or more of the tuning procedures described in this manual, you can proceed with thisfinal test to get your new bow ready to hunt. You will need three fletched arrows withfield tips and three with broadheads that weigh the same as your field tips.

Before you begin shooting, you will need to check your broadhead equippedarrows. After installing your broadheads, make sure they are perfectly straight on theshaft. This can be done by spinning the arrow on a flat counter while checking for anybroadhead wobble. You can also use a commercially made spin check tool that isavailable from your dealer. After all of your broad heads are spin-checked and straightyou are ready to begin.

Set up a broadhead target at twenty or thirty yards and shoot three arrows with fieldtips. Make sure you are properly warmed up and you are shooting to the best of yourability. Next, shoot three identically aimed arrows with broadheads. WARNING: NEVERSHOOT BARE SHAFTS WITH BROADHEADS ATTACHED. THE FLIGHT WILLBE EXTREMELY UNPREDICTABLE AND DANGEROUS. Once you have shot thebest group you can shoot, compare the position of the broadhead group to the field tipgroup. Compare the groups to the diagram below and make very small incrementaladjustments as described next to the broadhead group that corresponds to your arrowpattern. Note: make very small 1/32" adjustments. A small adjustment will greatlychange your broadhead flight.

20

Never - Dry fire your bow or shoot it without an arrow. This will result indamage to your bow and/or possible injury.

Never - Let anyone draw or shoot your bow if their draw length is longer thanyours. Over drawing of the bow can cause cable damage.

Never - Draw, aim, or shoot your bow unless you are sure that the line of fire isclear. Remember, once an arrow is fired it cannot be recalled.

Never - Shoot an arrow that is less than five grains per pound. For example, an80# bow requires a minimum of 400 grains of arrow weight. Less thanfive grains per pound of arrow weight simulates a dry fire effect and maydamage your bow.

Never - Expose your bow to extreme heat. Excessive heat, such as your car on ahot day, could lead to limb failure and premature wearing of the stringharness.

Always - Check all of your arrow shafts and nocks upon removal from the target.Do not shoot any arrows that show defects or broken nocks.

Always - Carefully inspect your bow after each use. Be sure all screws aresnug and accessories are tight. Inspect your string and cables for wearor damage.

Always - Draw your bow while pointing it at the target. A premature release of thearrow can be very dangerous. If you cannot draw your bow whilepointing it at the target without excessive movement, lower the peak weightof your bow until you can draw smoothly and correctly. Over time youwill build up strength, and will be able to return to the higher weight.

Always - Draw your bow with an arrow on the string while keeping it pointed in asafe direction. Never draw your bow with a release aid without an arrow.A release aid failure could result in the dry fire of your bow.

Always - Back your limb bolts off five full turns from the riser before putting it ina bow press. Only let a qualified professional or a Martin authorized dealerput your bow in a bow press. Inexperienced use of a bow press or aT-stringer can result in damage to your bow. This type of damage causedby a press is not covered under the Martin Archery bow warranty.

TEN COMMANDMENTS OF ARCHERY SAFETY

It is our goal at Martin Archery for you to realize your full potential as a newmember in the Martin family. We have some of the greatest shooters in the worldshooting with us and we are certain you can become one of them. Below are some ofthe most commonly asked questions about Martin archery equipment. We hope thatthese questions are useful to you.

What arrows should I use with my Martin bow? It is very important foraccurate shooting that your arrows are the correct spine, or stiffness, for your bow.Arrows that are too limber or too stiff will cause tuning and accuracy problems. Yourlocal dealer has an arrow chart and can properly fit your bow with the correct shaft.Regardless of the material or manufacturer of the arrow, all arrows have to be thecorrect spine or stiffness for your bow.

How is the draw length on my Martin bow measured? Martin Archerycurrently measures draw length according to the recommended AMO standard. Thisstandard dictates that the draw length be measured 1 forward of the pivot point, ormost inward point, of the grip.

How can I make my Martin bow as quiet as possible? Though your bow isengineered to produce very little noise, it is important to remember that highperformance models, that store high levels of energy, are not generally as quiet asmoderate performance bows. A few ways to eliminate noise and vibration are:a. Install string silencers.b. Make sure all screws on your setup are snug (a small amount of Lock-Tite will

help keep them tight).c. Set your draw weight closer to its maximum, lower settings can increase vibrations

and noise.d. Use a heavier arrow in order to absorb more of the bow's stored energy.e. Install mole skin between any attached accessory and the bows riser.

At what weight setting will my bow perform best? Your Martin bow can beshot anywhere within its fifteen pound weight range. You will achieve the highest levelof performance from any compound bow when it is set at its maximum draw weight.The maximum draw weight setting maintains the engineered level of limb, cable, andbowstring tension for peak efficiency, while keeping noise and vibration to aminimum.

I want to get the most arrow speed possible. How light can I make myarrows without causing damage to my bow? The durability of Martin bows isunsurpassed in the archery industry. All components of your new bow can withstandhigh levels of stress. Its unprecedented durability allows your Martin bow to easily usean arrow that weighs as little as 5 grains per pound of draw weight. Note: TheMartin Archery warranty does not allow the use of an arrow weighingless than five grains per pound.

What kind of string material can I use on my Martin bow? The strength ofall Martin bows, regardless of what cable system you are using, allows the use of allof the low stretch materials in use today. S-4, Spectra FastFlight, and 450 Premiumamong others are all good materials, and they can be used on all martin bows without voiding your warranty.

FREQUENTLY ASKED QUESTIONS

21

22

Whether your new bow is for hunting, 3-D, or for target shooting, you have made the rightdecision in choosing a Martin! Over forty years of archery experience are built into everyMartin bow. You can be confident that your new bow is designed to provide years of faithfulservice, and Martin will always be around to back it with our rock solid warranty.LIMITED 5-YEAR WARRANTY

Your Martin compound bow is guaranteed by Martin Archery, Inc. to be free from defectsin materials and workmanship for a period of two (2) years from the date ofpurchase. Exceptions to this warranty include the bow string and synthetic cables, for whichthere is no warranty. During the remainder of this Limited Five Year Warranty, MartinArchery, Inc. will offer repairs or replacements at a cost of 50% the current suggested listprice.

The warranty is conditioned upon proof of date of purchase and other conditions listedbelow. IT IS IMPORTANT THAT YOUR SALES RECEIPT BE FILED IN A SAFE PLACEFOR FUTURE REFERENCE, AS REPAIRS WILL NOT BE PERFORMED UNDERWARRANTY WITHOUT A COPY OF THE DATED SALES RECEIPT. Martin Archery,Inc. warrants that your Martin compound bow will perform its intended function if used inaccordance with the instructions provided. This Limited Warranty covers only the replace-ment parts, labor, and return ground transportation costs performed by Martin Archery Inc.to the customer. Transportation for the return of the bow to Martin Archery, Inc. are notcovered. No C.O.D. shipments will be accepted by Martin Archery, Inc. Warranty repairs canbe performed by an Authorized Martin Dealer, for which Martin Archery, Inc. will coverreplacement parts and ground transportation costs to the Authorized Dealer. Labor costs forwarranty repairs performed by Authorized Dealers are not covered by Martin Archery, Inc.Martin Archery makes no other warranty either expressed or implied, whether of fitness or ofmarketability, except as stated above. Any such additional warranty is expressly disclaimed.

Warranty limitations are as follows:1. If bow shows signs of misuse, alteration, or mishandling this warranty will be void. Use of

arrows weighing less than five (5) grains per pound of draw weight is considered misuseand will void this warranty.

2. Claimant must be the original purchaser. This warranty is not transferable.3. All returns to Martin Archery Inc. must be pre authorized. Owner must contact Martin

Archery, Inc. at (509) 529-2554 prior to shipping in order to obtain a ReturnAuthorization number.

4. All accessory items must be removed from the bow prior to shipping. Martin Archery, Inc.will not be responsible for damage or loss of any accessory item left on the bow.

5. Warranty is not effective unless a copy of the dated sales receipt accompanies the bow.6. This warranty gives you specific legal rights. You may also have other rights which vary

from state to state.* After acquiring a Return Authorization number, send bow to:

Martin Archery, Inc.3134 W, Highway 12Walla Walla, WA 99362

* This policy is subject to change and/or cancellation at the discretion of Martin Archery, Inc.

WARRANTY

NOTES