TemplateInfoTemplate Name:NdB OfficeTemplate Version:V3.11

NodeB(ATM)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULEATMADDRDWDENIPADDRDWIPMASKADDRIMAADDRDTADDRRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleATM AddressOMCB IP AddressOMCB IP Address MaskIMA Subsystem.IMA UnitDT Unit.DT SunitResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 1820 bytesIPV4STRINGSubsystem No.: 1 to 12,Unit No.: 1 to 17Unit No.: 1 to 17,Subunit No.:DTB (9 to 40),SDTB (9 to 71),SDTA (9 to 71, 93 to 155)1 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.Depend on the real situation.Depend on the real situation.This is invariably a 32-bit mask.The subsystem number is defined as (Rack No - 1) 4 + Shelf No. Each shelf is associated with one unique number. Unit No: the unit number of the IMAB board where the home IMA group of the link is located, that is, the unit number of the IMAB, SDTA or APBE, or the slot number. We can directly adopt the unit number of the IMA in the IMA group.Unit No.: the number of the slot where the DTB/SDTB/SDTA is located, Subunit No.: the number of the E1 line in the DTB board. The DTB board can accommodate 32 physical E1 lines, each corresponding uniquely to one subunit number. The subunit number ranges from 9 to 40. Subunit 9 corresponds to the first physical E1 line, and the numbering rule follows the ascending order. The SDTB board can accommodate 63 E1 lines, and the subunit number ranges from 9 to 71. The SDTA can accommodate 126 E1 lines, and the subunit number ranges from 9 to 71 and 93 to 155.Use ";" to seperate more values, for example:"5.9;5.10"If more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedRemark

NodeB(ATM MultiPath)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULEATMADDRDWDENIPADDRDWIPMASKADDRIUBPATHPROSWITCHRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleATM AddressOMCB IP AddressOMCB IP Address MaskIub Path Pro SwitchResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 1820 bytesIPV4STRINGON, OFF1 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.Depend on the real situation.Depend on the real situation.This is invariably a 32-bit mask.ON: Open Protection in IUB multipath productionOFF:Close Protection in IUB multipath productionIf more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyRemark

NodeB(ATM+IP)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULEATMADDRREMADDR1PATHGROUPBEARTYPETRPATHBANDWIDTHDWDENIPADDRDWIPMASKADDRIMAADDRDTADDRLOCADDR1IUBPATHPROSWITCHLOCPORTREMPORTPATHGROUPIDRUBSUBSYSTEMPLMNRSVRATIONEXTHOPAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleATM AddressNode B Service IPTransport Path Bear TypeDefault rate of IP Path(kbps)OMCB IP AddressOMCB IP Address MaskIMA Subsystem.IMA UnitDT Unit.DT SunitLocal IP of SCTPACIub Path Pro SwitchLocal-end port No.Peer-end port No.Father Path Group IdResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Next Hop of OMCBParameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 1820 bytesIPV42:ETHERNET, without VLANTAG5:ETHERNET, with VLANTAG64 to 1000000IPV4255.255.255.255Subsystem No.: 1 to 12,Unit No.: 1 to 17Unit No.: 1 to 17,Subunit No.:DTB (9 to 40),SDTB (9 to 71),SDTA (9 to 71, 93 to 155)IPV4ON, OFF1 to 655351 to 655350 to 20471 to 12,2550 to 1000valid IPV4,split by ";"Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.At present, the ATM address coding plan adopts uniformly the embedded NSAP address format. This field can be configured with its default value.This is the service IP address of the Node B.This is the beartype of Path Group ConfigurationUser plane bandwidth of IUB interfaceThis is the OMCB IP of the Node BThis is invariably a 32-bit mask.The subsystem number is defined as (Rack No - 1) 4 + Shelf No. Each shelf is associated with one unique number. Unit No: the unit number of the IMAB board where the home IMA group of the link is located, that is, the unit number of the IMAB, SDTA or APBE, or the slot number. We can directly adopt the unit number of the IMA in the IMA group.Unit No.: the number of the slot where the DTB/SDTB/SDTA is located, Subunit No.: the number of the E1 line in the DTB board. The DTB board can accommodate 32 physical E1 lines, each corresponding uniquely to one subunit number. The subunit number ranges from 9 to 40. Subunit 9 corresponds to the first physical E1 line, and the numbering rule follows the ascending order. The SDTB board can accommodate 63 E1 lines, and the subunit number ranges from 9 to 71. The SDTA can accommodate 126 E1 lines, and the subunit number ranges from 9 to 71 and 93 to 155.Use ";" to seperate more values, for example:"5.9;5.10"This is the RNC signaling plane IP address.ON: Open Protection in IUB multipath productionOFF: Open ATM+IP Dual-Stack protectionThis is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the father Path Group Id of the TrPath which its beartype is ethernet.If more than one PLMNRSVRATIO, separate each value by ";".Next-hop address of RNC that can bear OMCB in the IP channel. Usually, it is the IP address of the interface in the switch or router.DescriptionCan't be emptyParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedRemark

NodeB(IP)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULELOCADDR1REMADDR1PATHGROUPBEARTYPETXBITRATERXBITRATELOCPORTREMPORTPATHGROUPIDMAXRTOMINRTOINITRTOHEARTBEATDELAYACKRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleLocal IP of SCTPACRemote IP of SCTPACTransport Path Bear TypeForword bandwidth(kbps)Backward bandwidth(kbps)Local-end port No.Peer-end port No.Father Path Group IdMax. value of RTOMinmum Value of RTOInitialization value of RTOHeartbeat intervalsDelay ack timeResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 18IPV4IPV42:ETHERNET, without VLANTAG5:ETHERNET, with VLANTAG64 to 400000064 to 40000001 to 655351 to 655350 to 204710 to 300010 to 100010 to 300010 to 60000 to 201 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.This is the RNC signaling plane IP address.This is the service IP address of the Node B.This is the beartype of Path Group ConfigurationConfigure the actual physical bandwidth.Configure the actual physical bandwidth.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the father Path Group Id of the TrPath which its beartype is ethernet.This is the value of Max. value of RTOThis is the value of Minmum Value of RTOThis is the value of Initialization value of RTOThis is the value of Heartbeat intervalsThis is the value of Delay ack timeIf more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedRemark

NodeB(IP MultiPath)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULELOCADDR1REMADDR1PATHGROUPBEARTYPETRPATHBANDWIDTHLOCPORTREMPORTPATHGROUPIDLOCADDR1_2REMADDR1_2PATHGROUPBEARTYPE_2TRPATHBANDWIDTH_2LOCPORT_2REMPORT_2PATHGROUPID_2IUBPATHPROSWITCHRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleLocal IP of SCTPACRemote IP of SCTPACTransport Path Bear TypeDefault rate of IP Path(kbps)Local-end port No.Peer-end port No.Father Path Group IdLocal IP of SCTPACRemote IP of SCTPACTransport Path Bear TypeDefault rate of IP Path(kbps)Local-end port No.Peer-end port No.Father Path Group IdIub Path Pro SwitchResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 18IPV4IPV42:ETHERNET, without VLANTAG5:ETHERNET, with VLANTAG64 to 10000001 to 655351 to 655350 to 2047IPV4IPV42:ETHERNET, without VLANTAG5:ETHERNET, with VLANTAG64 to 10000001 to 655351 to 655350 to 2047ON, OFF1 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.This is the RNC signaling plane IP address.This is the service IP address of the Node B.This is the beartype of First Path Group ConfigurationUser plane bandwidth of IUB interfaceThis is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the father Path Group Id of the First TrPath which its beartype is ethernet.This is the RNC signaling plane IP address.This is the service IP address of the Node B.This is the beartype of Second Path Group ConfigurationUser plane bandwidth of IUB interfaceThis is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the father Path Group Id of the Second TrPath which its beartype is ethernet.ON: Open Protection in IUB multipath productionOFF:Close Protection in IUB multipath productionIf more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyRemark

NodeB(IPOE)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULELOCADDR1REMADDR1TRPATHBANDWIDTHEIPIADDRDTADDRLOCPORTREMPORTRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleLocal IP of SCTPACRemote IP of SCTPACDefault rate of IP Path(kbps)EIPI Subsystem.UnitDT Unit.DT SunitLocal-end port No.Peer-end port No.Resource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 18IPV4IPV464 to 1000000Subsystem No.: 1 to 12,Unit No.: 1 to 17Unit No.: 1 to 17,Subunit No.:DTB (9 to 40),SDTB (9 to 71),SDTB_2 (9 to 71, 93 to 155)1 to 655351 to 655351 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.This is the RNC signaling plane IP address.This is the IP address of the Node B.User plane bandwidth of IUB interfaceSubsystem No.: the number of the shelf where the EIPI board is located, Unit No.: the number of the slot where this board is located.Unit No.: the number of the slot where the DTB/SDTB/SDTI/DTI is located, Subunit No.: the number of the E1 line in the DTB board. The DTB board can accommodate 32 physical E1 lines, each corresponding uniquely to one subunit number. The subunit number ranges from 9 to 40. Subunit 9 corresponds to the first physical E1 line, and the numbering rule follows the ascending order. The SDTB board can accommodate 63 E1 lines, and the subunit number ranges from 9 to 71.Use ";" to seperate more values, for example:"5.9;5.10"This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.If more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedParameters can be modifiedRemark

&L&"Times New Roman,"ZTE&","&R&L&10&R&10 &N , &P

NodeB(IP+IPOE)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULELOCADDR1REMADDR1PATHGROUPBEARTYPETRPATHBANDWIDTHLOCPORTREMPORTPATHGROUPIDIPOE1LOCADDR1IPOE1REMADDR1IPOE1PATHGROUPBEARTYPEIPOE1TRPATHBANDWIDTHEIPIADDRDTADDRIPOE1LOCPORTIPOE1REMPORTIPOE1PATHGROUPIDIUBPATHPROSWITCHRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleLocal IP of SCTPACRemote IP of SCTPACTransport Path Bear TypeDefault rate of IP Path(kbps)Local-end port No.Peer-end port No.Father Path Group IdLocal IP of SCTPACRemote IP of SCTPACTransport Path Bear TypeDefault rate of IP Path(kbps)EIPI Subsystem.UnitDT Unit.DT SunitLocal-end port No.Peer-end port No.Father Path Group IdIub Path Pro SwitchResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 18IPV4IPV42:ETHERNET, without VLANTAG5:ETHERNET, with VLANTAG64 to 10000001 to 655351 to 655350 to 2047IPV4IPV44:IPOE1ORT1(MLPPP), with IP head compression7:IPOE1ORT1(MLPPP), without IP head compression64 to 1000000Subsystem No.: 1 to 12,Unit No.: 1 to 17Unit No.: 1 to 17,Subunit No.:DTB (9 to 40),SDTB (9 to 71),SDTB_2 (9 to 71, 93 to 155)1 to 655351 to 655350 to 2047ON, OFF1 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.This is the RNC signaling plane IP address.This is the service IP address of the Node B.This is the beartype of Path Group ConfigurationUser plane bandwidth of IUB interfaceThis is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the father Path Group Id of the First TrPath which its beartype is ethernet.This is the RNC signaling plane IP address.This is the IP address of the Node B.This is the beartype of Path Group ConfigurationUser plane bandwidth of IUB interfaceSubsystem No.: the number of the shelf where the EIPI board is located, Unit No.: the number of the slot where this board is located.Unit No.: the number of the slot where the DTB/SDTB/SDTI/DTI is located, Subunit No.: the number of the E1 line in the DTB board. The DTB board can accommodate 32 physical E1 lines, each corresponding uniquely to one subunit number. The subunit number ranges from 9 to 40. Subunit 9 corresponds to the first physical E1 line, and the numbering rule follows the ascending order. The SDTB board can accommodate 63 E1 lines, and the subunit number ranges from 9 to 71.Use ";" to seperate more values, for example:"5.9;5.10"This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the father Path Group Id of the First TrPath which its beartype is ethernet.ON: Open Protection in IUB multipath productionOFF:Close Protection in IUB multipath productionIf more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyRemark

&L&"Times New Roman,"ZTE&","&R&L&10&R&10 &N , &P

NodeB(ATM_STM)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULEATMADDRDWDENIPADDRDWIPMASKADDRRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleATM AddressOMCB IP AddressOMCB IP Address MaskResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 1820 shorts at most,split by "."valid IPV4valid mask,such as 255.255.255.2551 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.20 bytesIPV4STRINGIf more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyRemark

NodeB(ATM_STMIP)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULEATMADDRREMADDR1PATHGROUPBEARTYPETRPATHBANDWIDTHDWDENIPADDRDWIPMASKADDRLOCADDR1IUBPATHPROSWITCHLOCPORTREMPORTPATHGROUPIDRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleATM AddressNode B Service IPTransport Path Bear TypeDefault rate of IP Path(kbps)OMCB IP AddressOMCB IP Address MaskLocal IP of SCTPACIub Path Pro SwitchLocal-end port No.Peer-end port No.Father Path Group IdResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 1820 shorts at most,split by "."IPV42:ETHERNET, without VLANTAG5:ETHERNET, with VLANTAG64 to 1000000IPV4IPV4IPV4ON, OFF1 to 655351 to 655350 to 20471 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.20 bytesThis is the service IP address of the Node B.This is the beartype of Path Group ConfigurationUser plane bandwidth of IUB interfaceNode B O&M IPNode B O&M IP net maskThis is the RNC signaling plane IP address.ON: Open Protection in IUB multipath productionOFF:Close Protection in IUB multipath productionThis is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the port number of the associated local end, and must be the same as the Peer-End Port No. configured for the associated peer end.This is the father Path Group Id of the TrPath which its beartype is ethernet.If more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyParameters can be modifiedParameters can be modifiedRemark

NodeB(ATM_STM MultiPath)MODINDUSERLABELANIMCCMNCNEIDNDBALCMODULEATMADDRDWDENIPADDRDWIPMASKADDRIUBPATHPROSWITCHRUBSUBSYSTEMPLMNRSVRATIOAbbreviated NameModify IndicationUser LabelAAL2 Adjacent Office No.MCCMNCNode B IDNode B Home ModuleATM AddressOMCB IP AddressOMCB IP Address MaskIub Path Pro SwitchResource Allocation SubsystemRatio of occupied private bandwidth of Path Group by operator(%)Parameter NameA,D,M,S,PSTRING101 to 999o to 999o to 9990 to 655353 to 1820 shorts at most,split by "."valid IPV4valid mask,such as 255.255.255.255ON, OFF1 to 12,2550 to 1000Parameter ValueA: Add, D: Delete, M: Modify, S: Swap, P: PassThis is the Node B Name, which consists of 40 characters.In order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.If more than one MCC, separate each value by ";".If more than one MNC, separate each value by ";".Depend on the real situation.Each Node B must be homed to one RCP for processing. In principle, it is required that the geographically adjacent Node Bs should be processed by the same RCP module whenever possible.20 bytesIPV4STRINGON: Open Protection in IUB multipath productionOFF:Close Protection in IUB multipath production.If more than one PLMNRSVRATIO, separate each value by ";".DescriptionCan't be emptyRemark

PVCANIPVCIDSUBSYSTEMUNITCSUNITPVCSERVICECVPICVCIL2HSERVCATYL2HTRFTYPEL2HTRFPARA1L2HTRFPARA2L2HTRFPARA3L2HTRFPARA4L2HTRFPARA5PATHGROUPIDTRPATHIDPATHIDSERVICETYPEOWNERUSETYPECCPIDDTADDRAbbreviated NameOffice IDPVC IDSUBSYSTEMUNITSTM-1 Port NumberPVC service TypeCVPICVCIService TypeTraffic TypePeak cell rate for CLP=0+1(PCR0+1)(KBPS)Traffic Description Parameter 2Traffic Description Parameter 3Traffic Description Parameter 4Traffic Description Parameter 5PathGroup IDAAL2 Traffic Path IDAAL2 path intra-office S.N.AAL2 Path Service TypeAAL2 Path OwnerPort TypeNode B Port IDDT Unit.DT SunitParameter Name101 to 9991 to 10000The subsystem number is defined as (Rack No - 1) 4 + Shelf No. Each shelf is associated with one unique number.Unit No: the slot number of the APBE board.10 to 13AAL5 Signal, OMCB, AAL2 Data0 to 5110 to 65534CBR, RTVBR, NRTVBR, ABR, UBRatmClpTransparentNoScr,atmClpNoTaggingScrCdvt,atmNoClpNoScrNone.None.None.None.None.0 to 204732 to 1271 to 4160RT,NRT1,NRT2,NRT3,MIXLocal Office,Adjacent OfficeNCP,CCP,ALCAP0 to 65535Unit No.: 1 to 17,Subunit No.:DTB (9 to 40),SDTB (9 to 71),SDTA (9 to 71, 93 to 155)Parameter ValueIn order to avoid conflict with other NEs, the actual values of the Node B ANI range from 101 to 999.Unique in RNCAPBE SubsystemAPBE Unit10 is the first physical port.Depend on the real situation.For the external CVPI/CVCI, this is unique in the office and must be identical to the value of the connected office. It is recommended to use a value smaller than or equal to 4.For the external CVPI/CVCI, this is unique in the office and must be identical to the value of the connected office. It is recommended to use a value smaller than or equal to 256.IU interface: CBR is recommended.IUR interface: CBR is recommended for signaling, while a combination of CBR and UBR is recommended for service.Depend on the real situation.Depend on the real situation.Depend on the real situation. Usually, its SCR.Depend on the real situation. Usually, its MBS.Depend on the real situation. Usually, its CDVT.Depend on the real situation. Usually, its CDVT.This ID is globally unique.As the path ID of the AAL2 channel, this is globally unique and starts with 32 for the ATM office.As an interconnection parameter, this number must have the same configuration as the peer office.RT: for bearing real-time service,NRT1: for bearing R99 non-real-time service,NRT2: for bearing HS non-real-time service,MIX: for bearing all types of service.RT is recommended for the IUCS interface.RT and MTX are recommended for the IUR interface.If Local Office is configured, the AAL2 PATH ID will be allocated in the ascending order.If Adjacent Office is configured, the AAL2 PATH ID will be allocated in the descending order.For two interconnected RNCs, one end should be configured as the Local Office, while the other as the Adjacent Office.The Type of the PortThis is only available for CCP type.Unit No.: the number of the slot where the DTB/SDTB/SDTA is located, Subunit No.: the number of the E1 line in the DTB board. The DTB board can accommodate 32 physical E1 lines, each corresponding uniquely to one subunit number. The subunit number ranges from 9 to 40. Subunit 9 corresponds to the first physical E1 line, and the numbering rule follows the ascending order. The SDTB board can accommodate 63 E1 lines, and the subunit number ranges from 9 to 71. The SDTA can accommodate 126 E1 lines, and the subunit number ranges from 9 to 71 and 93 to 155.DescriptionRemark105105011313OMCB850CBRatmClpTransparentNoScr12810000105105111313AAL5 Signal851CBRatmClpTransparentNoScr12810000ALCAP105105211313AAL5 Signal852CBRatmClpTransparentNoScr12810000NCP105105311313AAL5 Signal853CBRatmClpTransparentNoScr12810000CCP1105105411313AAL2 Data854RTVBRatmClpNoTagginngScrCdvt144644821200010000201321RTLocal Office105105511313AAL2 Data855RTVBRatmClpNoTagginngScrCdvt144644821200010000201332RTLocal Office105105611313AAL2 Data856RTVBRatmClpNoTagginngScrCdvt144644821200010000202343RTLocal Office105105711313AAL2 Data857RTVBRatmClpNoTagginngScrCdvt144644821200010000202354RTAdjacent Office105105811313AAL2 Data858UBRatmNoClpNoScr14464201365NRT1Adjacent Office105105911313AAL2 Data859UBRatmNoClpNoScr14464202376NRT2Adjacent Office106106011313OMCB860CBRatmClpTransparentNoScr12810000106106111313AAL5 Signal861CBRatmClpTransparentNoScr12810000ALCAP106106211313AAL5 Signal862CBRatmClpTransparentNoScr12810000NCP106106311313AAL5 Signal863CBRatmClpTransparentNoScr12810000CCP1106106411313AAL5 Signal864CBRatmClpTransparentNoScr12810000CCP2106106511313AAL5 Signal865CBRatmClpTransparentNoScr12810000CCP3106106611313AAL2 Data866RTVBRatmClpNoTagginngScrCdvt144644821200010000203321RTLocal Office106106711313AAL2 Data867RTVBRatmClpNoTagginngScrCdvt144644821200010000203332RTLocal Office106106811313AAL2 Data868RTVBRatmClpNoTagginngScrCdvt144644821200010000204343RTLocal Office106106911313AAL2 Data869RTVBRatmClpNoTagginngScrCdvt144644821200010000204354RTAdjacent Office106107011313AAL2 Data870UBRatmNoClpNoScr14464203365NRT1Adjacent Office106107111313AAL2 Data871UBRatmNoClpNoScr14464204376NRT2Adjacent Office110110011313OMCB872CBRatmClpTransparentNoScr12810000110110111313AAL5 Signal873CBRatmClpTransparentNoScr12810000ALCAP110110211313AAL5 Signal874CBRatmClpTransparentNoScr12810000NCP110110311313AAL5 Signal875CBRatmClpTransparentNoScr12810000CCP1110110411313AAL2 Data876RTVBRatmClpNoTagginngScrCdvt144644821200010000205321RTLocal Office110110511313AAL2 Data877RTVBRatmClpNoTagginngScrCdvt144644821200010000205332RTLocal Office110110611313AAL2 Data878RTVBRatmClpNoTagginngScrCdvt144644821200010000206343RTLocal Office110110711313AAL2 Data879RTVBRatmClpNoTagginngScrCdvt144644821200010000206354RTAdjacent Office110110811313AAL2 Data880UBRatmNoClpNoScr14464205365NRT1Adjacent Office110110911313AAL2 Data881UBRatmNoClpNoScr14464206376NRT2Adjacent Office10711101318OMCB850CBRatmClpTransparentNoScr128100003.15;3.16;3.1710711111318AAL5 Signal851CBRatmClpTransparentNoScr12810000ALCAP3.15;3.16;3.1710711121318AAL5 Signal852CBRatmClpTransparentNoScr12810000NCP3.15;3.16;3.1710711131318AAL5 Signal853CBRatmClpTransparentNoScr12810000CCP13.15;3.16;3.1710711141318AAL2 Data854RTVBRatmClpNoTagginngScrCdvt144644821200010000201321RTLocal Office3.15;3.16;3.1710711151318AAL2 Data855RTVBRatmClpNoTagginngScrCdvt144644821200010000201332RTLocal Office3.15;3.16;3.1710711161319AAL2 Data856RTVBRatmClpNoTagginngScrCdvt144644821200010000202343RTLocal Office3.18;3.19;3.2010711171319AAL2 Data857RTVBRatmClpNoTagginngScrCdvt144644821200010000202354RTAdjacent Office3.18;3.19;3.2010711181318AAL2 Data858UBRatmNoClpNoScr14464201365NRT1Adjacent Office3.15;3.16;3.1710711191319AAL2 Data859UBRatmNoClpNoScr14464202376NRT2Adjacent Office3.18;3.19;3.20

IpPG InfoPATHGROUPIDTXBITRATERXBITRATEFATHERIDPath Group IDForword bandwidth(kbps)Backward bandwidth(kbps)Father Path Group ID0 to 204764 to 400000064 to 40000000 to 2047,65535This ID is globally unique.Configure the actual physical bandwidth.Configure the actual physical bandwidth.This ID is globally unique.