14-2 data forms

8/20/2019 14-2 data forms

1/12

APPENDIX A MQPS 14-2

CHOPPED STRAND GLASS MATDATA FORM CMA/1R

©Lloyds Register Group Limited 2013

!"#$

Mat reference number or grade:

Manufacturer:Address:

Standards complied with:

Keying agent type:Binder type:Applications:

Part 1-FIBRE AND MAT PROPERTIES

PROPERTYNominal

ValueTolerance Test Method

Filament alkali content (as Na2O) (%)

Average filament diameter (µµµµm)

Strand length (mm)

Strand count

Binder content (as % ignition loss)

Mass per unit area (g/mm2)

Variation in mass per unit area (%)

Moisture content (%)

Density of the glass (g/cm3)

Dimensions of standard rolls: Weight of standard rolls:Packaging details:Storage life:Recommended storage temperature:

Word 97 Version

http://cma-1r.doc/http://cma-1r.doc/

8/20/2019 14-2 data forms

2/12



© Lloyd’s Register Group Limited 2013

!"#$Part 2- TEST LAMINATE PROPERTIES

Tests to be conducted on a laminate containing a nominal 1800 g/m2 ofreinforcement with a 30-35% glass content using an approved resin. The laminate

is to be cured initially for not less than 24 hours at room temperature (18°- 21°C)and postcured for 16 hours at 40°C . Laminates subjected to more intensivepostcuring schedules will not be considered.

One copy of the Test House report and load extension curves must accompanythis data summary form.

LAMINATE PREPARATION

Polyester resin employed:

Manufacturer:

Mat nominal weight:

Number of plies:

Laminate thickness (mm):

Actual weight of resin used (kg):

Actual weight of mat used (kg):

8/20/2019 14-2 data forms

3/12




!"#$Part 3 QUALITY CONTROL SCHEDULE

List below the tests carried out for routine Quality Control purposes and the frequency ofthese tests.

Test Frequency

Signature ………………………………….(on behalf of manufacturer)

Position

Date

8/20/2019 14-2 data forms

4/12

APPENDIX B MQPS 14-2

FIBRE ROVINGS DATA FORM GRA/1R


!"#$Product reference number or grade:



Keying agent type:Approvals sought For spray-up and local reinforcement

For local reinforcement

Part 1-ROVING PROPERTIES (where applicable)

PROPERTYNominal




Strand count

Roving yield (tex)

Size content (%)


Density of the fibre material (g/cm3)

Standard windings:

Weight of standard package:Packaging details:Storage lifeRecommended storage temperature:

Word 97 version

http://gra-1r.doc/http://gra-1r.doc/http://gra-1r.doc/

8/20/2019 14-2 data forms

5/12




!"#$Part 2- TEST LAMINATE PROPERTIES(Applicable only to spray-up roving approvals)

Tests to be conducted on a laminate containing a nominal 1800 g/m2 of

reinforcement and 30-35% glass content produced by a glass/resin depositorusing an approved resin. The laminate is to be cured initially for not less than 24hours at room temperature (18°- 21°C) and postcured for 16 hours at 40°C .Laminates subjected to more intensive postcuring schedules will not beconsidered.



Resin employed:

Manufacturer:

Resin fibre depositor employed:(Manufacturer and Model No.)

Number of roving packages inSimultaneous use during spray-up:

Sprayed fibre length (mm):

Reinforcement weight(deposited):


8/20/2019 14-2 data forms

6/12






Test Frequency


Position

Date

8/20/2019 14-2 data forms

7/12

APPENDIX C MQPS 14-2

WOVEN ROVINGS DATA FORM WRA/1R


!"#$Product reference number or grade:



Keying agent type:

Part 1-FIBRE AND WOVEN ROVING PROPERTIES (where applicable)

PROPERTYNominal




Roving ends per 100 mm Warp:

Weft:

Linear density of rovings (tex) Warp:

Weft:

Residual size content (%)

Mass per unit area (g/m2)



Weave type:Standard roll width and length:Standard roll weight:Packaging details:Storage life:Recommended storage temperature:

Word 97 version

http://wra-1r.doc/http://wra-1r.doc/http://wra-1r.doc/

8/20/2019 14-2 data forms

8/12




!"#$Part 2- TEST LAMINATE PROPERTIES

Tests to be conducted on a laminate containing a nominal 50% glass content and2800 g/m2 of reinforcement produced by the hand lay-up process, using an

approved resin. The laminate is to be cured initially for not less than 24 hours atroom temperature (18°- 21°C) and postcured for 16 hours at 40°C . Laminatessubjected to more intensive postcuring schedules will not be considered.

All reinforcements are to be parallel plied during laminate construction.



Resin employed:

Manufacturer:

Weight of resin used:

Weight of reinforcement used


Number of plies:

Note If the reinforcement has a specific ‘moulded’ surface (e.g. the surface of thelaminate to be on the outside of the hull), flexural tests must be conducted with thissurface in tension.

8/20/2019 14-2 data forms

9/12






Test Frequency


Position

Date

8/20/2019 14-2 data forms

10/12

APPENDIX D MQPS 14-2COMPOSITE FIBRE REINFORCEMENTSDATA FORM CGR/2


!"#$Product reference number or grade:Manufacturer:Address:

Part 1-FIBRE AND COMPOSITE COMPONENT PROPERTIES

Method of bonding rovingand mat components:Where stitching is used to secure the mat please provide full detailsYarn type:Stitch:Direction:Count :

Keying agent on roving:Keying agent on mat:Mat binder type:

MAT ROVINGPROPERTY Mean

ValueTolerance

MeanValue

ToleranceTest Methods



Roving ends per 100 mm Warp: Weft:

Linear density of rovings (tex) Warp:

Weft:

Residual size content of rovings(%)

Mass per unit area (g/m2)

Moisture content as supplied (%):


Roving weave type:Standard roll width and length:Standard roll weight:Packaging details:Storage life

Recommended storage temperature:

Word 97 version

http://cgr2.doc/http://cgr2.doc/http://cgr2.doc/

8/20/2019 14-2 data forms

11/12



!"#$Part 2- TEST LAMINATE PROPERTIES(Applicable only to spray-up roving approvals)

Tests to be conducted on a laminate containing a nominal 2800 g/m2 ofreinforcement ,but consisting of not less than two plies, produced by the hand

lay-up process, using an approved resin. The laminate is to be cured initially fornot less than 24 hours at room temperature (18°- 21°C) and postcured for 16 hoursat 40°C . Laminates subjected to more intensive postcuring schedules will not beconsidered.

All reinforcements are to be parallel plied mat face downward during laminateconstruction.



Resin employed:

Manufacturer:

Weight of resin used:

Weight of reinforcement used:


Number of plies

Recommended range of fibre contentIn use for hand lay-up: % to %

8/20/2019 14-2 data forms

12/12





Test Frequency

Signature ………………………………….

(on behalf of manufacturer)

Position

Date

14-2 data forms

Documents