02 catalogue pompes - fps irrigation & industriel
TRANSCRIPT
Irrigation & Industrial Pumps
Mi1002 6.06
Submersible Pumps
Model Number ExplanationExample: 60FA10S4-PE
60 = GPM FA = FPS Series 10 = 10 HP S = Stainless 4 = 4" Submersible PE = Pump End
Features:■ 4 performance ranges - 35, 45, 60 & 90 GPM.
■ Stainless steel discharge head and motor bracket.
■ High fl ow impellers and stages are glass-fi lled Noryl®* for maximum effi ciency.
■ Ceramic shaft sleeve and rubber discharge bearing eliminates sand wear.
■ Intermediate bearing for increased shaft stability.
■ Floating eye and hub seals for improved performance and effi ciency.
■ Stainless steel hex pump shaft, shell and shaft coupling.
■ High capacity upthrust assembly for protection during start-up and operation (45, 60 and 90 GPM models).
■ Powered by Franklin’s corrosion-resistant 4” submersible motors.
■ 2” NPT Discharge.
■ Check valve must be ordered separately.
4400
4” High Capacity35, 45, 60 & 90 GPM Models
PAGE: SP-50DATE: Feb 5, 2007
* Noryl® is a Registered Trademark of G.E.
Submersible Pumps
Mi7900
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
4” High Capacity35-90 GPM Stainless Steel
1 - 10 HP 4" Pump Ends
GPM HP StagesOrdering Info. Dimensions
Wt.Old Model No. New Model No. Order No. Shell PEA
35
1 6 F4P35X6 35FA1S4-PE 93613506 11.10 15.00 9
1.5 8 F4P35X8 35FA15S4-PE 93613508 13.60 17.50 10
2 10 F4P35X10 35FA2S4-PE 93613510 16.10 20.00 11
3 14 F4P35X14 35FA3S4-PE 93613514 21.10 25.00 13
5 22 F4P35X22 35FA5S4-PE 93613522 31.10 35.00 17
45
1.5 6 F4P45X6 45FA15S4-PE 93614506 17.10 21.00 15
2 8 F4P45X8 45FA2S4-PE 93614508 21.60 25.50 16
3 11 F4P45X11 45FA3S4-PE 93614511 28.35 32.25 19
5 18 F4P45X18 45FA5S4-PE 93614518 43.85 47.75 25
7.5 26 F4P45X26 45FA7S4-PE 93614526 61.35 65.25 33
60
2 6 F4P60X6 60FA2S4-PE 93616006 17.10 21.00 15
3 8 F4P60X8 60FA3S4-PE 93616008 21.60 25.50 17
5 13 F4P60X13 60FA5S4-PE 93616013 32.85 36.75 21
7.5 17 F4P60X17 60FA7S4-PE 93616017 41.35 45.25 25
10 24 F4P60X24 60FA10S4-PE 93616024 57.10 61.00 31
90
2 5 F4P90X5 90FA2S4-PE 93919005 18.66 22.56 15
3 7 F4P90X7 90FA3S4-PE 93619007 24.66 28.56 17
5 12 F4P90X12 90FA5S4-PE 93619012 39.66 43.56 21
7.5 19 F4P90X19 90FA7S4-PE 93619019 60.60 64.50 27
1 - 1.5 HP Single-Phase Units
GPM HP Stages Volts2-Wire 3-Wire
Old Model No. New Model No. Order No. Wt. Old Model No. New Model No. Order No. Wt.
351 6 230 T1F4P35X6-S2 35FA1S4-2W230 93613606 33 1F4P35X6-S2 35FA1S4-3W230 93613706 33
1.5 8 230 T15F4P35X8-S2 35FA15S4-2W230 93613608 41 15F4P35X8-S2 35FA15S4-3W230 93613708 39
45 1.5 6 230 T15F4P45X6-S2 45FA15S4-2W230 93614606 46 15F4P45X6-S2 45FA15S4-3W230 93614706 44
Notes: All dimensions are in inches. Discharge is 2” NPT. Maximum diameter across cable guard is 3.90” on all models. Weight in pounds.
All listed above have 2” NPT discharge. Order check valve separately. Pump and motor will be individually cartoned and require assembly.
Notes:
Ordering Information
Submersible Pumps
4400
4” High Capacity35 GPM Performance Curves
PAGE: SP-55DATE: Feb 5, 2007
0
175
125
200
150
100
50
75
25
0
300
250
200
150
100
50
0
700
600
500
400
300
200
100
0 3010 20 40 50
0 62 4 108 12
ME
TE
RS
FE
ET
PS
I
GPM
M3PH
5 HP
3 HP
2 HP
1.5 HP
1 HP
60
55
50
45 EF
FIC
IEN
CY
%
1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage.
Notes:
Submersible Pumps
Mi7901
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
4” High Capacity35 GPM Performance Chart
Capacities in U.S. Gallons per Minute
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 450 500 550 600
1
0 - 48 44 39 34 28 21 1120 42 37 32 26 18 730 36 31 2540 30 24 1550 23 1460 127080
Shut-off PSI 65 57 48 39 31 22 13 5
1.5
0 - 49 46 43 40 36 32 27 22 16 820 45 42 39 35 31 26 20 1430 41 38 34 30 25 20 1340 37 33 29 24 18 1150 33 29 24 18 1060 28 23 17 970 22 16 780 14 3
Shut-off PSI 89 81 72 63 54 46 37 28 20 11 2
2
0 - 50 48 45 43 40 37 34 31 28 24 19 14 720 47 45 42 39 36 33 30 27 22 18 13 330 44 41 39 36 33 30 26 22 17 1240 41 38 35 32 29 25 21 16 1050 38 35 32 29 25 20 16 960 35 31 28 24 20 15 870 31 27 23 19 14 680 27 23 18 13 4
Shut-off PSI 116 107 99 90 81 73 64 55 47 38 29 21 12 3
3
0 - - 50 48 47 46 44 42 39 37 35 33 31 28 26 23 19 15 1020 49 48 47 45 43 41 39 37 35 33 30 28 25 22 18 14 830 48 46 45 43 41 39 37 35 32 30 27 25 21 17 13 740 46 44 42 40 38 36 34 32 29 27 24 20 17 12 550 44 42 40 38 36 34 31 29 26 24 20 16 12 460 42 40 38 36 33 31 29 26 23 19 15 11 270 39 37 35 33 31 28 26 22 19 15 1080 37 35 33 30 28 25 22 18 14 9
Shut-off PSI 165 156 148 139 130 122 113 104 96 87 78 70 61 52 44 35 26 18 9
5
0 - - - - 50 49 48 47 46 45 44 43 42 40 39 38 37 36 34 33 30 25 20 1220 - - 49 48 48 47 46 45 44 42 41 40 39 38 36 35 34 33 32 30 26 20 1330 - 49 48 47 46 45 44 43 42 41 40 39 38 36 35 34 33 31 30 28 23 17 840 49 48 47 46 45 44 43 42 41 40 39 37 36 35 34 32 31 30 28 26 21 1350 48 47 46 45 44 43 42 41 40 38 37 36 35 33 32 31 30 28 26 24 18 960 47 46 45 44 43 42 41 39 38 37 36 34 33 32 31 29 28 26 24 21 1470 46 45 44 43 42 40 39 38 37 35 34 33 32 31 29 27 25 23 21 18 1080 45 44 42 41 40 39 38 36 35 34 33 32 30 29 27 25 23 20 18 15 3
Shut-off PSI 268 259 251 242 233 225 216 207 199 190 181 173 164 155 147 138 129 121 12 103 82 60 38 17
Sh
ut-
off
288
ft
Sh
ut-
off
226
ft
Sh
ut-
off
171
ft
Sh
ut-
off
496
ft
Sh
ut-
off
638
ft
Submersible Pumps
4400
4” High Capacity45 GPM Performance Curves
PAGE: SP-60DATE: Feb 5, 2007
0
175
125
200
150
100
50
75
25
225
250
300
350
350
400
450
300
250
200
150
100
50
0 0
100
200
300
400
500
600
700
800
900
1000
ME
TE
RS
FE
ET
PS
I
0 10 20 30 40 50 60 70 80
0 62 4 108 12 14 16 18
GPM
M3PH
60
40
50
EF
FIC
IEN
CY
%
7.5 HP
5 HP
3 HP
2 HP
1.5 HP
1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage. 3. Performance for former XP models are the same as 45 gpm models.
Notes:
Submersible Pumps
Mi7902
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
4” High Capacity45 GPM Performance Chart
Capacities in U.S. Gallons per Minute
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance20 40 60 80 100 120 140 160 180 200 240 260 280 300 320 340 360 380 400
1.5
0 68 62 57 52 46 39 3110 62 56 51 45 38 29 1920 55 50 44 36 28 17 530 49 42 35 26 16 340 41 34 25 1450 33 23 1260 22 10
Shut-off PSI 74 65 56 48 39 30 22 13 4
2
0 71 65 60 56 52 48 44 40 35 2910 64 59 55 51 48 44 40 34 28 2020 58 54 51 47 43 39 33 27 19 930 54 50 47 43 38 32 26 17 740 50 46 42 37 32 24 16 550 45 41 36 31 23 14 360 41 36 29 22 13 1.5
Shut-off PSI 104 95 87 78 69 61 52 43 35 26 9
3
0 72 68 65 62 59 56 53 50 47 43 36 31 26 2010 68 64 61 58 55 52 49 46 43 39 30 25 19 1220 64 61 58 55 52 49 46 42 38 34 2430 60 57 54 52 48 45 42 38 34 29 1740 57 54 51 48 45 41 37 33 28 22 1650 54 51 47 44 41 37 32 27 21 1560 50 47 44 40 36 31 26 20 1470 46 43 39 35 31 25 19 1380 43 39 35 30 24 18 1290 38 34 29 24 18 11100 33 28 23 16 9
Shut-off PSI 143 134 126 117 108 100 91 82 74 65 48 39 30 22 13 4
5
0 - - 69 66 63 61 59 57 55 53 50 48 46 44 42 40 38 36 3320 68 65 63 60 57 56 54 52 51 49 46 44 42 40 38 35 32 29 2640 62 60 57 56 54 52 50 48 48 47 45 39 37 34 32 28 25 2160 57 55 51 51 50 48 46 44 43 41 36 33 31 27 24 20 1680 53 51 49 47 46 44 42 40 38 35 30 26 23 19100 49 47 45 43 41 39 37 34 32 29 25 18120 45 43 41 39 36 34 31 28 24 20 16140 40 38 35 33 30 27 23 19160 35 32 29 26 22 18170 31 28 25 21 17
Shut-off PSI 236 227 219 210 201 193 184 175 167 158 141 132 123 115 106 97 89 80 71
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950
7.5
0 - - - 57 54 50 47 44 40 36 32 28 24 18 11 320 - - 57 54 50 47 44 40 36 32 28 24 18 11 340 - 58 54 51 48 45 41 37 33 29 24 18 12 560 58 55 52 48 45 41 37 33 29 25 19 12 580 55 52 48 45 41 37 33 29 25 19 12 5100 52 48 45 42 38 34 30 25 20 14 6120 49 45 42 38 34 30 25 21 14 7140 45 42 38 35 30 26 21 15 7160 42 39 35 31 26 21 15 8180 39 35 31 27 22 16 8200 35 31 27 22 16 9220 32 27 22 17 10
Shut-off PSI 331 310 288 266 245 223 201 180 158 136 115 93 71 50 28 6
Sh
ut-
off
350
ft
Sh
ut-
off
250
ft
Sh
ut-
off
190
ft
Sh
ut-
off
575
ft
Sh
ut-
off
815
ft
Submersible Pumps
4400
4” High Capacity60 GPM Performance Curves
PAGE: SP-65DATE: Feb 5, 2007
60
40
50
EF
FIC
IEN
CY
%
0
175
125
200
150
100
50
75
25
225
250
275
300
350
400
450
300
250
200
150
100
50
0 0
100
200
300
400
500
600
700
800
900
1000
0 62 4 108 12 14 16 18 M3PH
0 10 20 30 40 50 60 70 80 GPM
ME
TE
RS
FE
ET
PS
I
10 HP
7.5 HP
5 HP
3 HP
2 HP
1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage. 3. Performance for former YP models are the same as 60 gpm models.
Notes:
Submersible Pumps
Mi7903
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
4” High Capacity60 GPM Performance Chart
Capacities in U.S. Gallons per Minute
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180
2
0 87 84 81 78 75 72 69 66 62 58 54 4910 80 77 74 71 68 65 61 57 52 47 42 3620 74 70 67 64 60 56 51 46 40 34 26 1830 66 63 59 54 49 44 38 31 24 1640 57 53 48 42 36 29 21 1350 46 40 34 27 1960 32 24 16
Shut-off PSI 74 69 65 61 56 52 48 43 39 30 26 22 17 13 9 4
3
0 90 87 85 83 81 79 76 74 72 70 67 65 62 59 56 53 4910 84 82 80 78 76 74 71 69 67 64 61 58 55 51 47 43 3820 79 77 75 73 71 68 66 63 60 57 54 50 46 42 37 32 2630 74 72 70 68 65 59 56 53 49 45 40 35 30 2440 69 67 64 62 58 55 52 48 43 39 34 28 2250 63 61 58 54 50 46 42 37 32 2660 56 63 49 45 41 36 30 24
Shut-off PSI 108 104 100 95 91 87 82 78 74 69 65 61 56 52 48 43 39
HP PSI 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340
5
0 85 85 80 80 75 75 70 70 65 65 60 55 50 45 45 35 3010 85 80 80 75 75 70 70 65 60 60 55 50 45 40 35 30 2520 80 80 75 75 70 70 65 60 60 55 50 45 40 35 30 25 1530 80 75 75 70 65 65 60 60 55 50 45 40 35 30 20 15 540 75 70 70 65 65 60 55 55 50 45 40 35 30 25 10 550 70 70 65 65 60 55 55 50 45 40 35 25 25 10 560 70 65 65 60 55 50 50 45 40 30 25 20 10 570 65 60 60 55 50 45 40 35 30 25 15 1080 60 60 55 50 45 40 35 30 25 15 1090 60 55 50 45 40 35 30 20 15 5100 55 50 45 40 35 30 20 15 5
Shut-off PSI 173 165 156 147 139 130 121 113 104 95 87 78 69 61 52 43 35
HP PSI 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850
7.5
0 - 78 73 68 63 56 49 40 28 15 220 78 73 68 63 56 49 40 28 15 240 75 69 64 58 50 41 30 18 360 70 64 58 50 42 31 18 480 65 59 51 43 32 19 5100 59 52 43 32 20 6120 52 44 33 21 8140 44 34 21 8160 35 22 9
Shut-off PSI 221 199 177 156 134 113 91 69 48 26 4
10
0 - - 75 72 69 65 61 56 51 45 38 30 21 13 420 - 75 72 69 65 61 56 51 46 38 31 22 14 540 75 72 69 65 61 56 51 45 39 31 22 14 560 73 69 66 62 57 52 47 40 32 24 15 680 70 66 62 57 52 47 40 32 24 15 6100 66 62 58 53 48 41 34 25 16 7120 63 58 53 48 41 34 25 16 8140 58 53 48 42 34 26 17 8160 54 49 43 35 27 18 9
Shut-off PSI 312 290 269 247 225 204 182 161 139 117 96 74 52 31 9
Sh
ut-
off
425
ft
Sh
ut-
off
265
ft
Sh
ut-
off
195
ft
Sh
ut-
off
555
ft
Sh
ut-
off
772
ft
Submersible Pumps
4400
4” High Capacity90 GPM Performance Curves
PAGE: SP-70DATE: Feb 5, 2007
60
40
50
EF
FIC
IEN
CY
%
0
125
100
50
75
25
0
175
125
150
100
50
75
25
350
400
450
300
250
200
150
100
50
00 10 20 30 40 50 60 70 80 11010090 120 130
0 62 4 108 12 14 16 18 302826242220
ME
TE
RS
FE
ET
PS
I
M3PH
GPM
7.5 HP
5 HP
3 HP
2 HP
1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage.
Notes:
Submersible Pumps
Mi7904
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
4” High Capacity90 GPM Performance Chart
Capacities in U.S. Gallons per Minute
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance
20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180
2
0 130 120 110 100 90 80 70 60 45 30 1010 105 100 90 80 70 55 40 2020 85 75 65 50 35 1530 60 45 30 1040 25 5
Shut-off PSI 43 39 35 30 26 22 17 13 9 4
3
0 140 130 120 115 105 100 95 90 80 75 65 55 45 30 1510 120 110 105 100 95 85 80 70 65 55 40 25 1020 105 95 90 85 80 70 60 50 35 20 5430 90 80 75 65 55 45 35 1540 75 65 55 40 30 1050 50 40 25 560 20
Shut-off PSI 64 59 55 51 46 42 38 33 29 25 20 16 12 7 3
HP PSI 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340
5
0 145 135 125 120 110 105 95 85 80 70 55 45 30 1010 135 125 115 110 100 95 85 75 65 55 40 25 1020 125 115 110 100 95 85 75 65 55 40 25 530 115 105 100 90 85 75 65 50 40 20 540 105 100 90 80 70 60 50 35 2050 95 90 80 70 60 45 35 1560 90 80 70 60 45 30 1570 80 70 55 45 30 1080 65 55 40 25 590 50 40 25 5100 35 20
Shut-off PSI 115 106 97 89 80 71 63 54 45 37 28 19 11 2
HP PSI 20 50 80 110 140 170 200 230 260 290 320 350 380 410 440 470 500
7.5
0 140 135 125 115 110 100 95 85 75 65 55 45 30 1520 130 120 110 105 95 90 80 70 60 50 35 20 530 120 115 105 100 90 85 75 65 55 40 25 1040 115 110 100 95 85 75 65 55 45 30 1050 110 105 95 85 80 70 60 45 30 1560 105 95 90 80 70 60 50 35 20 580 95 85 75 65 55 40 25 10100 80 70 60 50 35 20120 65 55 40 25 10140 45 35 20160 25 10
Shut-off PSI 175 162 149 136 123 110 97 84 71 58 45 32 19 6
Sh
ut-
off
285
ft
Sh
ut-
off
167
ft
Sh
ut-
off
120
ft
Sh
ut-
off
425
ft
Submersible Pumps
Model Number ExplanationExample: 50FA15S6-PE
50 = GPM FA = FPS Series 15 = 1.5 HP S = Stainless 6 = 6" Submersible PE = Pump End
Features:■ Heavy-duty stainless steel discharge head and motor bracket.
■ Stainless steel shaft, shell, intake screen and cable shield for corrosion resistance and longer life.
■ Stainless steel wear ring and Urethane fl oating eye seal for improved performance and effi ciency.
■ Glass-fi lled Noryl®* impeller stage assemblies provide incredible strength and durability.
■ Ceramic shaft sleeve and rubber discharge bearing minimizes bearing wear and shaft misalignment without affecting pump effi ciency.
■ 3” NPT tapping in heavy-duty stainless steel discharge head.
■ Fastener kit supplied for both 4” and 6” motors enabling 5-10 hp units to be mounted to either a 4" or 6" submersible motor.
■ One year unconditional warranty against failure from sand locking in abrasive well conditions.
4400
6” High Capacity50 - 125 GPM
PAGE: SP-100DATE: Mar 31, 2008
* Noryl® is a Registered Trademark of G.E.
Submersible Pumps
Ordering Information
6" Pump Ends
GPM HP StagesMotor
FitOrdering Info. Dimensions
Wt.Model No. Order No. Pump End Only
50
1.5 3 4" 50FA15S6-PE 94825003 13.51 30
2 4 4" 50FA2S6-PE 94825004 15.13 31
3 5 4" 50FA3S6-PE 94825005 16.76 32
5 8 4" & 6" 50FA5S6-PE 94825008 21.63 36
7.5 11 4" & 6" 50FA7S6-PE 94825011 26.51 40
10 15 4" & 6" 50FA10S6-PE 94825015 32.94 46
75
3 3 4" 75FA3S6-PE 94827503 13.51 30
5 5 4" & 6" 75FA5S6-PE 94827505 16.76 32
7.5 7 4" & 6" 75FA7S6-PE 94827507 20.01 35
10 9 4" & 6" 75FA10S6-PE 94827509 23.26 38
15 13 6" 75FA15S6-PE 94827513 29.76 43
20 17 6" 75FA20S6-PE 94827517 36.19 48
25 23 6" 75FA25S6-PE 94827523 46.00 54
100
5 3 4" & 6" 100FA5S6-PE 94820003 14.62 32
7.5 5 4" & 6" 100FA7S6-PE 94820005 18.51 32
10 6 4" & 6" 100FA10S6-PE 94820006 20.49 34
15 9 6" 100FA51S6-PE 94820009 26.31 38
20 13 6" 100FA20S6-PE 94820013 34.07 43
25 16 6" 100FA25S6-PE 94820016 39.94 47
125
5 2 4" & 6" 125FA5S6-PE 94822502 12.94 29
7.5 3 4" & 6" 125FA7S6-PE 94822503 15.05 30
10 4 4" & 6" 125FA10S6-PE 94822504 17.13 31
15 7 6" 125FA15S6-PE 94822507 23.37 35
20 9 6" 125FA20S6-PE 94822509 27.54 38
25 11 6" 125FA25S6-PE 94822511 31.70 40
30 13 6" 125FA30S6-PE 94822513 35.87 43
40 18 6" 125FA40S6-PE 94822518 46.27 48
Note: All dimensions are in inches. Discharge is 3" NPT. Maximum diameter across cable guard is 5.5" on all models. Weight in pounds.
Mi8001
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
6” High Capacity50-125 GPM
Submersible Pumps
6” High Capacity50 GPM Performance Curve
PAGE: SP-105DATE: Feb 5, 2007
4400
0
100
200
300
400
500
600
700
800
0 10 20 30 40 50 60 70 80 90
10 HP
7.5 HP
5 HP
3 HP
2 HP
1.5 HP
0
175
125
200
150
100
50
75
25
225
250350
300
250
200
150
100
50
0
ME
TE
RS
PS
I
FE
ET
0 62 4 108 12 14 16 18 20 22 M3PH
GPM
10
20
30
40
50
60
70
EF
FIC
IEN
CY
%
Submersible Pumps
6” High Capacity50 GPM Performance Chart
Mi8002
Capacities in U.S. Gallons per Minute
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750 800
1.5
0 73 69 61 52 38 2720 59 48 36 2030 47 34 1440 32 1050
Shut-off PSI 51 42 34 25 16 8
2
0 79 74 68 63 56 48 39 30 1120 66 61 54 45 37 2530 60 53 45 34 2240 52 43 34 2050 42 33 1960 30 12
Shut-off PSI 74 65 56 48 39 30 22 13 4
3
0 - 78 74 70 65 58 55 49 41 1520 72 68 64 58 54 47 38 33 2030 67 63 57 52 45 38 30 1540 61 57 51 45 38 29 1450 56 49 45 37 29 1460 48 41 35 25 12
Shut-off PSI 97 88 79 71 62 53 45 36 27 6
5
0 - - - 78 75 73 70 67 64 55 45 34 1220 - 77 74 72 69 66 63 57 56 45 34 1630 77 74 71 68 65 62 59 56 52 41 2540 74 71 67 65 62 59 55 50 46 36 1650 71 67 64 62 58 54 50 46 42 2760 67 65 60 57 53 50 45 41 36 19
Shut-off PSI 164 156 147 139 130 121 113 104 95 74 52 30 9
7.5
0 - - - - - 78 76 74 72 67 62 57 49 42 29 1620 - - 79 78 75 74 72 70 68 62 57 49 41 30 1730 - 79 77 75 73 71 70 68 65 60 53 47 37 26 1240 79 77 74 73 71 69 67 65 62 57 49 42 29 1850 76 74 72 71 70 67 65 62 60 54 47 37 26 1460 74 72 70 69 67 65 61 60 58 52 45 32 19
Shut-off PSI 239 230 222 213 204 196 187 178 170 148 126 105 83 61 40 18
10
0 - - - - - - - 79 77 74 70 67 63 58 55 49 45 36 28 17 620 - - - - - 79 77 76 74 71 67 63 59 56 50 46 37 29 18 830 - - - - 78 77 75 74 72 70 65 61 57 52 47 40 29 27 1440 - - - 78 76 75 73 72 71 67 64 60 54 49 43 36 29 1850 - - 79 77 75 73 72 71 69 65 62 57 53 47 41 34 26 1460 - 78 76 74 73 72 70 69 68 64 60 54 49 44 38 29 18
Shut-off PSI 332 323 315 306 297 289 280 272 263 241 220 198 176 155 133 111 90 68 46 25 3
Sh
ut-
off
158
ft
Sh
ut-
off
210
ft
Sh
ut-
off
263
ft
Sh
ut-
off
420
ft
Sh
ut-
off
592
ft
Sh
ut-
off
807
ft
Discharge tapping 3” FNPT. 1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage.
Notes:
Submersible Pumps
6” High Capacity75 GPM Performance Curve
PAGE: SP-110DATE: Mar 31, 2008
4400
25 hp
20 hp
15 hp
10 hp
7.5 hp
5 hp
3 hp
800
1000
1200
600
400
200
00 20 40 60 80 100 120
70
60
50
0 62 4 108 12 14 16 18 20 22 24 26 M3PH
GPME
FF
ICIE
NC
Y%
0
175
125
200
150
100
50
75
25
225
250 350
300
250
200
275
300
325
350
375
450
400
450
150
100
50
0
ME
TE
RS
PS
I
FE
ET
Submersible Pumps
6” High Capacity75 GPM Performance Chart
Mi8003
Capacities in U.S. Gallons per Minute
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000
3
0 115 104 96 86 74 5520 93 82 70 5130 80 67 4640 65 4150 37
Shut-off PSI 53 45 36 27 19 10
5
0 - - 105 102 96 89 83 76 6520 105 100 93 88 82 73 65 5230 99 92 87 80 72 64 4940 92 88 79 69 62 4550 85 76 69 62 4460 77 68 58 42
Shut-off PSI 96 87 78 70 61 52 44 35 26
7.5
0 - - - - - 107 103 99 94 84 69 5020 - 109 105 100 97 94 90 85 79 71 5030 108 104 100 97 93 88 83 78 69 63 4040 108 104 99 96 93 88 83 77 73 5150 103 100 96 92 87 82 75 70 63 4060 100 95 91 85 80 75 69 63 55
Shut-off PSI 152 144 135 126 118 109 100 92 93 61 40 18
10
0 - - - - - - 110 106 104 97 88 77 65 4820 - - - - 109 106 103 99 96 88 79 66 4830 - - - 108 106 102 99 96 93 84 74 60 4040 - - 108 105 102 99 96 92 89 80 68 5250 - 108 103 102 99 93 92 89 84 74 62 4260 107 103 100 98 96 91 88 84 80 68 53
Shut-off PSI 202 193 184 176 167 158 150 141 132 111 89 67 46 24
15
0 - - - - - - - - - 110 105 100 95 89 81 74 65 56 3920 - - - - - - - - 110 105 101 94 89 81 76 67 58 4130 - - - - - - - - 110 104 98 92 86 80 72 66 4940 - - - - - - - 110 107 102 96 90 82 75 70 58 4050 110 107 104 99 94 86 80 72 65 49 3060 110 109 107 103 102 96 90 82 76 69 58 46
Shut-off PSI 300 291 282 274 265 256 248 239 230 209 187 165 144 122 101 79 57 36 14
20
0 - - - - - - - - - - - 110 106 103 98 92 88 83 78 69 63 54 4020 - - - - - - - - - - 110 106 102 98 91 89 84 78 72 64 58 4430 - - - - - - - - - 110 109 105 98 94 90 86 80 75 69 61 50 3540 - - - - - - - - - 110 107 102 98 91 88 84 79 72 68 55 4550 - - - - - - - - 110 109 105 100 95 91 87 80 75 70 63 52 3860 - - - - - - - - 110 107 102 98 93 88 84 80 73 66 58 45
Shut-off PSI 389 381 372 363 355 346 337 329 320 298 277 255 233 212 190 168 147 125 103 82 60 39 17
HP PSI 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150
25
0 - - 110 107 102 99 96 94 91 86 83 78 75 71 65 58 51 3820 - 110 107 103 100 96 93 90 86 82 79 75 72 66 60 51 3930 - 109 106 101 99 95 92 89 85 81 77 73 71 64 58 47 3440 110 107 104 100 97 93 91 87 82 79 75 71 67 62 52 4250 109 106 101 99 95 92 89 85 81 77 73 69 65 57 47 3560 108 104 100 97 94 91 88 84 80 75 71 67 62 54 42
Shut-off PSI 394 372 361 329 307 286 264 242 221 199 177 156 134 113 91 69 48 26
Sh
ut-
off
163
ft
Sh
ut-
off
261
ft
Sh
ut-
off
392
ft
Sh
ut-
off
460
ft
Sh
ut-
off
732
ft
Sh
ut-
off
939
ft
Sh
ut-
off
121
0 ft
Discharge tapping 3” FNPT. 1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage.
Notes:
Submersible Pumps
6” High Capacity100 GPM Performance Curve
PAGE: SP-111DATE: Mar 31, 2008
4400
0 2 0 4 0 6 0 8 0 10 0 12 0 14 00
1 00
2 00
3 00
4 00
5 00
6 00
7 00
8 00
9 00
10 00
0
100
2 00
3 00
0 5 9 14 18 2 3 2 7 3 2
0
100
200
3 00
4 00
50
60
ME
TE
RS
PS
I
FE
ET
25 hp
20 hp
15 hp
10 hp
7.5 hp
5 hp
EF
FIC
IEN
CY
%
M3PH
GPM
Submersible Pumps
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance20 40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050
5
0 - - - 130 119 104 85 62 2920 138 127 115 98 78 54 1530 125 113 95 75 49 640 110 92 71 4450 89 68 3860 64 3270 26
Shut-off PSI 74 65 57 48 39 31 22 13 5
7.5
0 - - - - - 138 131 123 115 107 79 3220 - - - 136 129 121 113 104 94 82 3730 - - 135 128 120 111 102 92 80 64 440 - 134 126 118 110 101 90 77 62 4250 133 125 117 109 99 88 75 59 38 1060 124 116 107 98 86 73 56 34 570 115 106 96 84 71 53 30
Shut-off PSI 130 121 113 104 95 87 78 69 61 52 30 9
10
0 - - - - - - 140 134 127 121 102 79 4520 - - - - 138 132 125 118 111 104 81 4830 - - - 137 131 124 117 110 102 94 67 2840 - - 136 130 123 116 109 101 92 83 51 250 - 135 129 122 115 108 100 91 81 70 3160 134 128 121 114 107 99 90 80 68 54 770 127 120 113 105 97 88 78 66 52 35
Shut-off PSI 162 153 144 136 127 118 110 101 92 84 62 40 19
15
0 - - - - - - - - - - 133 123 111 98 82 61 3220 - - - - - - - - 138 134 123 112 100 83 62 3430 - - - - - - - 137 133 129 118 107 93 75 51 1940 - - - - - - 136 132 128 124 113 101 85 64 3750 - - - - 140 136 132 128 124 119 108 94 76 53 2160 - - - 139 135 131 127 123 119 114 102 86 66 39 370 - - 138 135 131 126 122 118 113 109 95 78 55 24
Shut-off PSI 247 238 230 221 212 204 195 186 178 169 147 126 104 82 61 39 17
20
0 - - - - - - - - - - - - 134 127 119 111 103 94 83 69 52 2920 - - - - - - - - - - - 134 127 120 112 104 94 83 70 53 3130 - - - - - - - - - - 138 131 124 116 108 99 90 78 63 44 1940 - - - - - - - - - - 135 128 120 112 104 95 84 71 55 33 450 - - - - - - - - - 139 132 124 117 109 100 90 79 64 45 2160 - - - - - - - - 138 135 128 121 113 105 96 85 72 56 35 770 - - - - - - - 138 135 132 125 117 109 101 91 80 65 47 23
Shut-off PSI 358 349 340 332 323 314 306 297 289 280 258 237 215 193 172 150 128 107 85 63 42 20
25
0 - - - - - - - - - - - - - 135 130 124 118 111 104 96 88 78 67 54 37 1720 - - - - - - - - - - - - 135 130 125 119 112 105 97 88 79 68 55 39 1830 - - - - - - - - - - - 138 133 128 122 116 109 101 93 84 74 62 48 30 740 - - - - - - - - - - - 136 130 125 119 112 105 97 89 79 69 56 40 2050 - - - - - - - - - - 138 133 128 122 116 109 102 94 85 75 63 49 31 960 - - - - - - - - - - 136 131 125 119 113 106 98 90 80 69 57 41 2270 - - - - - - - - - 139 134 128 123 117 110 102 94 85 75 64 50 33 11
Shut-off PSI 385 377 368 359 338 316 294 273 251 229 208 186 164 143 121 99
6” High Capacity100 GPM Performance Chart
Mi8004
Capacities in U.S. Gallons per Minute
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Sh
ut-
off
191
ft
Discharge tapping 3” FNPT. 1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage.
Notes:
Sh
ut-
off
320
ft
Sh
ut-
off
393
ft
Sh
ut-
off
590
ft
Sh
ut-
off
846
ft
Sh
ut-
off
103
0 ft
Submersible Pumps
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance20 40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100
5
0 - - - 140 106 6220 153 131 95 3430 126 88 1240 82506070
Shut-off PSI 48 39 30 22 13 4
7.5
0 - - - - 157 141 122 99 6420 - - 152 136 116 90 4830 - 150 133 112 85 3940 147 130 109 79 2950 127 105 73 1860 101 6770 60
Shut-off PSI 77 69 60 51 43 34 25 17 8
6” High Capacity125 GPM Performance Curve & Chart
PAGE: SP-112DATE: Mar 31, 2008
0 20 40 60 80 100 120 140 16 00
100
200
30 0
40 0
500
600
700
80 0
90 0
1000
1100
1200
0
100
200
300
0 5 9 14 18 23 27 32 36
0
100
200
300
400
500
50
60
70
ME
TE
RS
PS
I
FE
ET
40 hp
30 hp
25 hp
20 hp
15 hp
10 hp
7.5 hp
5 hp
EF
FIC
IEN
CY
%
M3PH
GPM
Sh
ut-
off
130
ft
Sh
ut-
off
198
ft
Capacities in U.S. Gallons per Minute
Discharge tapping 3” FNPT. 1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage.
Notes:
Continued on reverse
Submersible Pumps
HP PSIDepth to Pumping Water Level, or Lift, in Feet
Shaded Areas Indicate Most Effi cient Performance20 40 60 80 100 120 140 160 180 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100
10
0 - - - - - - 155 143 129 114 4520 - - - - 151 139 125 109 88 5430 - - - 150 137 122 106 84 4740 - 159 148 135 120 103 79 3950 157 146 132 118 100 74 3060 144 130 115 97 69 2170 128 113 93 64 10
Shut-off PSI 105 97 88 79 71 62 53 45 36 27 6
15
0 - - - - - - - - - - 151 134 112 81 2820 - - - - - - - - 158 152 135 114 84 3430 - - - - - - - 158 151 145 126 102 6540 - - - - - - 157 150 144 137 116 87 3950 - - - - - 156 149 143 136 128 104 68 360 - - - - 155 148 142 134 126 117 89 4470 - - 160 154 147 141 133 125 116 106 72 10
Shut-off PSI 185 176 168 159 150 142 133 124 116 94 72 51 29 7
20
0 - - - - - - - - - - - 155 143 129 113 92 59 520 - - - - - - - - - - 156 144 130 114 93 62 1030 - - - - - - - - - - 151 138 123 105 81 4140 - - - - - - - - - 157 145 131 115 95 65 1550 - - - - - - - - 157 152 139 124 107 83 4560 - - - - - - - 156 151 146 132 117 97 68 2070 - - - - - 160 155 150 145 140 125 108 85 49
Shut-off PSI 252 243 234 226 217 208 200 191 182 174 152 130 109 87 66 44 22 1
25
0 - - - - - - - - - - - - - 153 143 133 119 99 71 3120 - - - - - - - - - - - - 154 144 134 120 101 74 3530 - - - - - - - - - - - 159 149 140 128 112 90 57 1340 - - - - - - - - - - - 155 145 135 121 103 76 3850 - - - - - - - - - - 160 150 140 129 114 92 60 1660 - - - - - - - - - - 155 146 135 123 105 78 4270 - - - - - - - - - - 151 141 130 115 94 63 20
Shut-off PSI 292 283 275 266 257 249 240 231 210 188 166 145 123 102 80 58 37 15
30
0 - - - - - - - - - - - - - - 152 143 134 125 113 99 79 54 2220 - - - - - - - - - - - - - 153 144 135 126 114 100 81 56 2530 - - - - - - - - - - - - 158 149 140 131 121 108 92 70 43 840 - - - - - - - - - - - - 153 145 136 126 115 101 83 58 2750 - - - - - - - - - - - 158 149 141 132 122 109 93 72 45 1060 - - - - - - - - - - - 154 145 137 127 116 102 84 61 3070 - - - - - - - -- - - 159 150 141 132 122 110 95 74 47 13
Shut-off PSI 326 317 309 300 291 270 248 226 205 183 161 140 118 96 75 53 31
40
0 - - - - - - - - - - - - - - - - - 156 150 144 138 132 125 117 107 96 8020 - - - - - - - - - - - - - - - - 156 150 145 139 132 126 118 108 97 82 6230 - - - - - - - - - - - - - - - 160 154 148 142 136 129 122 114 103 90 73 5240 - - - - - - - - - - - - - - - 157 151 145 139 133 126 118 109 98 83 64 4050 - - - - - - - - - - - - - - - 154 148 142 136 130 123 114 104 91 75 54 2660 - - - - - - - - - - - - - - 157 151 145 140 133 127 119 110 98 84 66 42 1170 - - - - - - - - - - - - - - 155 149 143 137 130 123 115 105 92 76 55 29
Shut-off PSI 409 387 365 344 322 300 279 257 235 214 192 171
6” High Capacity125 GPM Performance Chart
Mi8005
Capacities in U.S. Gallons per Minute
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Sh
ut-
off
263
ft
Discharge tapping 3” FNPT. 1. Performance shown does not include friction loss in the drop pipe. 2. All performance data is based on rated motor nameplate voltage.
Notes:
Sh
ut-
off
467
ft
Sh
ut-
off
601
ft
Sh
ut-
off
734
ft
Sh
ut-
off
873
ft
Sh
ut-
off
119
4 ft
Submersible Turbine Pumps
Model Number ExplanationExample: 175ST10D6B-0464 175 = GPM ST = Sub Turbine 10 = Horsepower D = Ductile Iron 6 = 6” Pump B = Impeller Trim 04 = Number of stages 6 = 6” Motor 4 = 4” Discharge
Features:■ 100% Franklin factory tested.
■ Ductile iron discharge and suction bracket.
■ Ductile iron bowls bolt together for easy service.
■ Stainless upthrust bolt provides exceptional upthrust protection.
■ Bronze discharge bearing is grease packed for maximum bearing protection.
■ Fluted rubber bearings in all bowls.
■ Suction inlet located above bottom bearing prevents abrasives from entering the bearing.
■ Suction bracket design allows easy access to coupling.
■ Bronze bracket bearing is protected with stainless steel sand collar.
■ Stainless steel impellers with stainless steel taper lock secures impeller to shaft.
■ Stainless steel pump shaft for increased durability.
■ Shaft coupling is keyed to pump by set screws and is splined to fi t motor shaft.
■ All models have 6” motor fi t.
■ 4” Discharge tapping FNPT.
6” Submersible Turbine Pump100 to 375 GPM
PAGE: SP-200DATE: Mar 1, 2009
Submersible Turbine Pumps
6” Submersible Turbine PumpOrdering Information
6" Submersible Turbine Pump Ends
GPM HP Stages Trim Size Motor Bracket Size
DischargeSize Order No. Model No. Weight
100
5 3 B 6” 4” NPT 96060100103 100ST5D6B-0364 717.5 5 B 6” 4” NPT 96060100105 100ST7D6B-0564 9110 6 1A, 5B 6” 4” NPT 96060100306 100ST10D6X-0664 10115 10 B 6” 4” NPT 96060100110 100ST15D6B-1064 14120 10 9A, 1B 6” 4” NPT 96060100310 100ST20D6X-1064 14125 14 7A, 7B 6” 4” NPT 96060100314 100ST25D6X-1464 18230 15 13A, 2B 6” 4” NPT 96060100315 100ST30D6X-1564 19240 20 18A, 2B 6” 4” NPT 96060100320 100ST40D6X-2064 242
150
5 2 1A, 1B 6” 4” NPT 96060150302 150ST5D6X-0264 647.5 3 2A, 1B 6” 4” NPT 96060150303 150ST7D6X-0364 7610 5 B 6” 4” NPT 96060150105 150ST10D6B-0564 8815 6 4A, 2B 6” 4” NPT 96060150306 150ST15D6X-0664 10720 7 A 6” 4” NPT 96060150007 150ST20D6A-0764 11925 9 A 6” 4” NPT 96060150009 150ST25D6A-0964 14330 11 10A, 1B 6” 4” NPT 96060150311 150ST30D6X-1164 16740 15 14A, 1B 6” 4” NPT 96060150315 150ST40D6X-1564 21550 18 A 6” 4” NPT 96060150018 150ST50D6A-1864 250
175
5 2 B 6” 4” NPT 96060175102 175ST5D6B-0264 657.5 3 B 6” 4” NPT 96060175103 175ST7D6B-0364 7710 4 1A, 3B 6” 4” NPT 96060175304 175ST10D6X-0464 8915 6 2A, 4B 6” 4” NPT 96060175306 175ST15D6X-0664 11420 7 5A, 2B 6” 4” NPT 96060175307 175ST20D6X-0764 12625 8 A 6” 4” NPT 96060175008 175ST25D6A-0864 13830 10 9A, 1B 6” 4” NPT 96060175310 175ST30D6X-1064 16240 13 A 6” 4” NPT 96060175013 175ST40D6A-1364 19950 16 A 6” 4” NPT 96060175016 175ST50D6A-1664 23560 19 A 6” 4” NPT 96060175019 175ST60D6A-1964 271
200
5 1 A 6” 4” NPT 96060200001 200ST5D6A-0164 537.5 2 B 6” 4” NPT 96060200102 200ST7D6B-0264 6610 3 2B, 1C 6” 4” NPT 96060200303 200ST10D6X-0364 7815 4 1A, 3B 6” 4” NPT 96060200404 200ST15D6X-0464 9020 5 3A, 2B 6” 4” NPT 96060200305 200ST20D6X-0564 10325 6 A 6” 4” NPT 96060200006 200ST25D6A-0664 11530 7 A 6” 4” NPT 96060200007 200ST30D6A-0764 12840 9 A 6” 4” NPT 96060200009 200ST40D6A-0964 15250 12 A 6” 4” NPT 96060200012 200ST50D6A-1264 18960 14 A 6” 4” NPT 96060200014 200ST60D6A-1464 214
225
5 2 1A, 1B 6” 4” NPT 96060225302 225ST5D6X-0264 657.5 3 1A, 2B 6” 4” NPT 96060225303 225ST7D6X-0364 7710 4 2A, 2B 6” 4” NPT 96060225304 225ST10D6X-0464 8915 5 A 6” 4” NPT 96060225005 225ST15D6A-0564 10120 7 6A, 1B 6” 4” NPT 96060225307 225ST20D6X-0764 12825 9 7A, 2B 6” 4” NPT 96060225309 225ST25D6X-0964 14930 11 8A, 3B 6” 4” NPT 96060225311 225ST30D6X-1164 17240 14 13A, 1B 6” 4” NPT 96060225314 225ST40D6X-1464 20450 17 A 6” 4” NPT 96060225017 225ST50D6A-1764 238
Note: Order check valve separately.
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Mi8010
Submersible Turbine Pumps
6” Submersible Turbine PumpOrdering Information
Mi8011400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
6" Submersible Turbine Pump Ends
GPM HP Stages Trim Size Motor Bracket Size
DischargeSize Order No. Model No. Weight
275
5 1 A 6” 4” NPT 96060275001 275ST5D6A-0164 537.5 2 A 6” 4” NPT 96060275002 275ST7D6A-0264 6610 3 2A, 1B 6” 4” NPT 96060275303 275ST10D6X-0364 7715 4 A 6” 4” NPT 96060275004 275ST15D6A-0464 9020 5 A 6” 4” NPT 96060275005 275ST20D6A-0564 10525 7 6A, 1B 6” 4” NPT 96060275307 275ST25D6X-0764 12530 8 A 6” 4” NPT 96060275008 275ST30D6A-0864 13840 11 10A, 1B 6” 4” NPT 96060275311 275ST40D6X-1164 17250 14 12A, 2B 6” 4” NPT 96060275314 275ST50D6X-1464 21460 16 A 6” 4” NPT 96060275016 275ST60D6A-1664 235
325
5 2 C 6” 4” NPT 96060325202 325ST5D6C-0264 657.5 2 1A, 1B 6” 4” NPT 96060325302 325ST7D6X-0264 6510 3 B 6” 4” NPT 96060325103 325ST10D6B-0364 7715 4 3A, 1C 6” 4” NPT 96060325304 325ST15D6X-0464 8920 5 A 6” 4” NPT 96060325005 325ST20D6A-0564 10125 6 A 6” 4” NPT 96060325006 325ST25D6A-0664 11330 7 A 6” 4” NPT 96060325007 325ST30D6A-0764 12540 10 A 6” 4” NPT 96060325010 325ST40D6A-1064 16150 12 A 6” 4” NPT 96060325012 325ST50D6A-1264 18460 15 A 6” 4” NPT 96060325015 325ST60D6A-1564 220
375
5 1 A 6” 4” NPT 96060375001 375ST5D6A-0164 537.5 2 B 6” 4” NPT 96060375102 375ST7D6B-0264 6510 2 A 6” 4” NPT 96060375002 375ST10D6A-0264 6515 4 B 6” 4” NPT 96060375104 375ST15D6B-0464 8920 5 1A, 4B 6” 4” NPT 96060375305 375ST20D6X-0564 10125 6 3A, 3B 6” 4” NPT 96060375306 375ST25D6X-0664 11330 7 5A, 2B 6” 4” NPT 96060375307 375ST30D6X-0764 12540 9 A 6” 4” NPT 96060375009 375ST40D6A-0964 14950 11 A 6” 4” NPT 96060375011 375ST50D6A-1164 17260 13 A 6” 4” NPT 96060375013 375ST60D6A-1364 196
PAGE: SP-201DATE: Mar 1, 2009
Note: Order check valve separately.
Submersible Turbine Pumps
Model 100ST6 Performance PAGE: SP-203DATE: Mar 1, 2009
4 GPM10
FT
0 20 40 60 80 100 120 1400
50
100
150
200
250
300
350
400
450
500
550
600
650
0
20
40
60
80
100
120
140
160
180
200
0 5 10 15 20 25 30
60
65
70
5 hp
10 hp
7.5 hp
15 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Model 100ST6 Performance
Dimension Information
P
M
MD
5.88
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
5 3 B 6” 27.32 22.90 5.38 101 71
7.5 5 B 6” 34.32 24.20 5.38 108 91
10 6 1A, 5B 6” 37.82 25.40 5.38 116 101
15 10 B 6” 51.82 28.00 5.38 129 141
Mi8012
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Submersible Turbine Pumps
Model 100ST6 Performance PAGE: SP-205DATE: Mar 1, 2009
4 GPM20
FT
0 20 40 60 80 100 120 140400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
150
200
250
300
350
400
450
500
0 5 10 15 20 25 30
60
65
70
20 hp
30 hp
25 hp
40 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Dimension Information
P
M
MD
5.88
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
20 10 9A, 1B 6” 51.82 30.60 5.38 145 141
25 14 7A, 7B 6” 65.32 33.10 5.38 156 182
30 15 13A, 2B 6” 69.32 35.70 5.38 174 192
40 20 18A, 2B 6” 86.82 40.80 5.38 202 242
Model 100ST6 Performance
Mi8013
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Model 100ST6 Performance PAGE: SP-207DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. Effi ciency correction required for low stage count (1 stage-6%, 2 stage-2%, 3 stage-1%) Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor. Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
Trim A Diameter C AngleA 4.688” 5 °
B 4.200” 0 °
C 3.688” 0 °
Impeller DimensionsA
C
Mi8014
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
4 GPM
1 F
T
0 20 40 60 80 100 120-15
-10
-5
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
-4
-2
0
2
4
6
8
10
12
14
16
18
20
22
24
26
0 5 10 15 20 25 30
0.00
0.75
1.50
2.25
3.00
Trim C
Trim B
Trim A
Trim C
Trim B
66%
69%
Trim A
68%
64%
64%66%
0.0
1.0
2.0
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Turbine Pumps
Model 150ST6 Performance PAGE: SP-209DATE: Mar 1, 2009
5 GPM10
FT
0 25 50 75 100 125 150 175 200 2250
50
100
150
200
250
300
350
400
450
500
550
0
20
40
60
80
100
120
140
160
180
0 5 10 15 20 25 30 35 40 45 50
60
65
70
75
15 hp
5 hp
10 hp
7.5 hp
20 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Model 150ST6 Performance
Dimension Information
P
M
MD
5.88
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
5 2 1A, 1B 6” 26.32 22.90 5.38 101 64
7.5 3 2A, 1B 6” 31.07 24.20 5.38 108 76
10 5 B 6” 40.57 25.40 5.38 116 88
15 6 4A, 2B 6” 45.27 28.00 5.38 129 107
20 7 A 6” 50.02 30.60 5.38 135 119
Mi8015
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Submersible Turbine Pumps
Model 150ST6 Performance PAGE: SP-211DATE: Mar 1, 2009
5 GPM20
FT
0 25 50 75 100 125 150 175 200 225200
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
100
150
200
250
300
350
400
450
0 5 10 15 20 25 30 35 40 45 50
60
65
70
75
50 hp
30 hp
25 hp
40 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Dimension Information
P
M
MD
5.88
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
25 9 A 6” 59.57 33.10 5.38 148 143
30 11 10A, 1B 6” 69.57 35.70 5.38 162 167
40 15 14A, 1B 6” 88.02 40.80 5.38 195 215
50 18 A 6” 102.32 57.80 5.38 310 250
Model 150ST6 Performance
Mi8016
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Model 150ST6 Performance PAGE: SP-213DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. Effi ciency correction required for low stage count (1 stage-6%, 2 stage-3%, 3 stage-1%) Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor. Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
Trim A Diameter C AngleA 4.688” 27 °
B 4.250” 27 °
C 3.750” 27 °
Impeller DimensionsA
C
Mi8017
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
5 GPM
1 F
T
0 25 50 75 100 125 150 175 200-15
-10
-5
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
-4
-2
0
2
4
6
8
10
12
14
16
18
20
22
24
0 5 10 15 20 25 30 35 40 45 50
0.00
1.00
2.00
3.00
4.00
Trim A
Trim B
Trim C
Trim CTrim B
Trim A
70%
68%
68%
70%
71%69%
69%
0.0
1.0
2.0
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Turbine Pumps
Model 175ST6 Performance PAGE: SP-215DATE: Mar 1, 2009
5 GPM10
FT
0 25 50 75 100 125 150 175 200 225 2500
50
100
150
200
250
300
350
400
450
500
550
0
20
40
60
80
100
120
140
160
180
0 5 10 15 20 25 30 35 40 45 50 55
60
65
70
15 hp
5 hp
10 hp
7.5 hp
20 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Model 175ST6 Performance
Dimension Information
P
M
MD
5.88
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
5 2 B 6” 26.32 22.90 5.38 101 65
7.5 3 B 6” 31.07 24.20 5.38 108 77
10 4 1A, 3B 6” 35.82 25.40 5.38 116 89
15 6 2A, 4B 6” 45.32 28.00 5.38 129 114
20 7 5A, 2B 6” 50.02 30.56 5.38 135 126
Mi8018
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Submersible Turbine Pumps
Model 175ST6 Performance PAGE: SP-217DATE: Mar 1, 2009
5 GPM20
FT
0 25 50 75 100 125 150 175 200 225 250200
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
100
150
200
250
300
350
400
450
0 5 10 15 20 25 30 35 40 45 50 55
60
65
70
60 hp
50 hp
30 hp
25 hp
40 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Dimension Information
P
M
MD
5.88
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
25 8 A 6” 54.82 33.10 5.38 148 138
30 10 9A, 1B 6” 64.27 35.70 5.38 162 162
40 13 A 6” 78.52 40.80 5.38 195 199
50 16 A 6” 92.82 57.80 5.38 310 235
60 19 A 6” 107.07 63.80 5.38 340 271
Model 175ST6 Performance
Mi8019
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Model 175ST6 Performance PAGE: SP-219DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. Effi ciency correction required for low stage count (1 stage-6%, 2 stage-2%, 3 stage-1%) Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor. Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
Trim A Diameter C AngleA 4.688” 20 °
B 4.250” 20 °
C 3.750” 20 °
Impeller DimensionsA
C
Mi8060
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
5 GPM
1 F
T
0 25 50 75 100 125 150 175 200 225 250
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
-4
-2
0
2
4
6
8
10
12
14
16
18
20
22
24
0 5 10 15 20 25 30 35 40 45 50 55 60
0.00
1.00
2.00
3.00
4.00
Trim C
Trim B
Trim A
Trim CTrim B
Trim A
68%
68%
67%66%
70%69%
67%66%
69%
0.0
1.0
2.0
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Turbine Pumps
Model 200ST6 Performance PAGE: SP-221DATE: Mar 1, 2009
5 GPM
5 F
T
0 25 50 75 100 125 150 175 200 225 250 275 300 3250
25
50
75
100
125
150
175
200
225
250
275
300
325
350
375
0
10
20
30
40
50
60
70
80
90
100
110
120
0 10 20 30 40 50 60 70
60
65
70
15 hp
5 hp
10 hp
7.5 hp
20 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Model 200ST6 Performance
Dimension Information
P
M
MD
5.88
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
5 1 A 6” 21.57 22.90 5.38 101 53
7.5 2 B 6” 26.32 24.20 5.38 108 66
10 3 2B, 1C 6” 31.02 25.40 5.38 116 78
15 4 1A, 3B 6” 35.82 28.00 5.38 129 90
20 5 3A, 2B 6” 40.57 30.60 5.38 135 103
Mi8061
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Submersible Turbine Pumps
Model 200ST6 Performance PAGE: SP-223DATE: Mar 1, 2009
5 GPM
10 F
T
0 25 50 75 100 125 150 175 200 225 250 275 300 325200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
80
100
120
140
160
180
200
220
240
260
280
300
320
0 10 20 30 40 50 60 70
60
65
70
60 hp
50 hp
30 hp
25 hp
40 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Dimension Information
P
M
MD
5.88
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
25 6 A 6” 45.32 33.10 5.38 148 115
30 7 A 6” 50.07 35.70 5.38 162 128
40 9 A 6” 59.57 40.80 5.38 195 152
50 12 A 6” 73.82 57.80 5.38 310 189
60 14 A 6” 83.32 63.80 5.38 340 214
Model 200ST6 Performance
Mi8062
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Model 200ST6 Performance PAGE: SP-225DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. Effi ciency correction required for low stage count (1 stage-6%, 2 stage-2%) Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor. Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
Trim A Diameter C AngleA 4.625” 30 °
B 4.438” 30 °
C 4.250” 30 °
Impeller DimensionsA
C
Mi8063
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
5 GPM
1 F
T
0 25 50 75 100 125 150 175 200 225 250 275
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
-4
-2
0
2
4
6
8
10
12
14
16
18
20
22
24
0 5 10 15 20 25 30 35 40 45 50 55 60 65
1.00
2.00
3.00
4.00
5.00
Trim CTrim B
Trim A
Trim A
Trim B
Trim C
68%
68%
67%
66%
65%
69%
67%66%
65%
1.0
2.0
3.0
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Turbine Pumps
Model 225ST6 Performance PAGE: SP-227DATE: Mar 1, 2009
5 GPM10
FT
0 25 50 75 100 125 150 175 200 225 250 275 300 3250
50
100
150
200
250
300
350
400
450
500
0
20
40
60
80
100
120
140
160
0 10 20 30 40 50 60 70
60
65
70
75
15 hp
5 hp
10 hp
7.5 hp
20 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Model 225ST6 Performance
Dimension Information
P
M
MD
5.88
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
5 2 1A, 1B 6” 26.30 22.90 5.38 101 65
7.5 3 1A, 2B 6” 31.10 24.20 5.38 108 77
10 4 2A, 2B 6” 35.80 25.40 5.38 116 89
15 5 5A 6” 40.60 28.00 5.38 129 101
20 7 6A, 1B 6” 50.10 30.60 5.38 145 128
Mi8064
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Submersible Turbine Pumps
Model 225ST6 Performance PAGE: SP-229DATE: Mar 1, 2009
5 GPM20
FT
0 25 50 75 100 125 150 175 200 225 250 275 300 325100
200
300
400
500
600
700
800
900
1000
1100
1200
50
100
150
200
250
300
350
0 10 20 30 40 50 60 70
60
65
70
75
50 hp
30 hp
25 hp
40 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Dimension Information
P
M
MD
5.88
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
25 9 7A, 2B 6” 59.56 33.10 5.38 156 149
30 11 8A, 3B 6” 69.10 35.70 5.38 174 172
40 14 13A, 1B 6” 83.30 40.80 5.38 202 204
50 17 17A 6” 97.60 55.30 5.38 300 238
Model 225ST6 Performance
Mi8065
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Model 225ST6 Performance PAGE: SP-231DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. No effi ciency correction needed for low stage count pumps. Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor. Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
Trim A Diameter C AngleA 4.472” 25.5 °
B 3.972” 25.5 °
C 3.472” 25.5 °
Impeller DimensionsA
C
Mi8066
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
5 GPM
1 F
T
0 25 50 75 100 125 150 175 200 225 250 275 300 325
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
-6
-4
-2
0
2
4
6
8
10
12
14
16
18
20
22
24
0 10 20 30 40 50 60 70
0.0
1.0
2.0
3.0
4.0
70%
72%
64%
60%54%
54%
60%
68%74%
72%70%
68%64%
Trim CTrim B
Trim A
Trim A
Trim B
Trim C
0
1
2
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Turbine Pumps
Model 275ST6 Performance PAGE: SP-233DATE: Mar 1, 2009
10 GPM
5 F
T
0 50 100 150 200 250 300 350 4000
25
50
75
100
125
150
175
200
225
250
275
300
325
350
375
0
10
20
30
40
50
60
70
80
90
100
110
120
0 10 20 30 40 50 60 70 80 90
60
65
70
75
15 hp
5 hp
10 hp
7.5 hp
20 hp
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Met
ers
Fee
t
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Model 275ST6 Performance
Dimension Information
P
M
MD
5.88
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
5 1 1A 6” 21.57 22.90 5.38 101 53
7.5 2 2A 6” 26.32 24.20 5.38 108 66
10 3 2A, 1B 6” 31.07 25.40 5.38 116 77
15 4 4A 6” 35.82 28.00 5.38 129 90
20 5 5A 6” 40.57 30.60 5.38 145 105
Mi8067
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Submersible Turbine Pumps
Model 275ST6 Performance PAGE: SP-235DATE: Mar 1, 2009
10 GPM20
FT
0 50 100 150 200 250 300 350 400100
200
300
400
500
600
700
800
900
1000
1100
1200
50
100
150
200
250
300
350
0 10 20 30 40 50 60 70 80 90
60
65
70
75
60 hp
50 hp
30 hp
25 hp
40 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Dimension Information
P
M
MD
5.88
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
25 7 6A, 1B 6” 50.10 33.10 5.38 156 125
30 8 8A 6” 54.80 35.70 5.38 174 138
40 11 10A, 1B 6” 69.10 40.80 5.38 202 172
50 14 12A, 2B 6” 83.30 55.30 5.38 300 214
60 16 16A 6” 92.80 61.30 5.38 330 235
Model 275ST6 Performance
Mi8068
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Model 275ST6 Performance PAGE: SP-237DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. No effi ciency correction needed for low stage count pumps. Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor. Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
Trim A Diameter C AngleA 4.568” 17 °
B 4.193” 17 °
C 3.818” 17 °
Impeller DimensionsA
C
Mi8069
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
10 GPM
1 F
T
0 50 100 150 200 250 300 350
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
-4
-2
0
2
4
6
8
10
12
14
16
18
20
22
24
0 10 20 30 40 50 60 70 80 90
1.0
2.0
3.0
4.0
5.0
72%
68%
65%62%
62%65%
70%
74%
72%70%
68%
Trim CTrim B
Trim A
Trim A
Trim B
Trim C
1
2
3
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Turbine Pumps
Model 325ST6 Performance PAGE: SP-239DATE: Mar 1, 2009
10 GPM
10 F
T
0 50 100 150 200 250 300 350 400 4500
50
100
150
200
250
300
350
400
0
20
40
60
80
100
120
0 20 40 60 80 100
55
60
65
70
20 hp
15 hp
10 hp
7.5 hp
5 hpE
ffici
ency
(%
)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Met
ers
Fee
t
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Model 325ST6 Performance
Dimension Information
P
M
MD
5.88
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
5 2 C 6” 26.32 22.90 5.38 101 65
7.5 2 1A, 1B 6” 26.32 24.20 5.38 108 65
10 3 B 6” 31.07 25.40 5.38 116 77
15 4 3A, 1C 6” 35.82 28.00 5.38 129 89
20 5 A 6” 40.57 30.60 5.38 135 101
Mi8070
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Submersible Turbine Pumps
Model 325ST6 Performance PAGE: SP-241DATE: Mar 1, 2009
10 GPM
20 F
T
0 50 100 150 200 250 300 350 400 450100
200
300
400
500
600
700
800
900
1000
1100
40
80
120
160
200
240
280
320
0 20 40 60 80 100
55
60
65
70
60 hp
50 hp
40 hp
30 hp
25 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Dimension Information
P
M
MD
5.88
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
25 6 A 6” 45.32 33.10 5.38 148 113
30 7 A 6” 50.07 35.70 5.38 162 125
40 10 A 6” 64.32 40.80 5.38 195 161
50 12 A 6” 73.82 57.83 5.38 310 184
60 15 A 6” 88.07 63.83 5.38 340 220
Model 325ST6 Performance
Mi8071
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Model 325ST6 Performance PAGE: SP-243DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. No effi ciency correction needed for low stage count pumps. Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor. Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
Trim A Diameter C AngleA 4.500” 30 °
B 4.250” 30 °
C 4.000” 30 °
Impeller DimensionsA
C
Mi8072
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
10 GPM
1 F
T
0 50 100 150 200 250 300 350 400
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
0
5
10
15
20
0 20 40 60 80 100
0.0
1.0
2.0
3.0
4.0
5.0
57%
70%
63%67%
69%70%
69%
67%
57%
63%
71%
Trim CTrim B
Trim A
Trim A
Trim B
Trim C
0
1
2
3
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Turbine Pumps
Model 375ST6 Performance PAGE: SP-245DATE: Mar 1, 2009
10 GPM
5 F
T
0 50 100 150 200 250 300 350 400 450 5000
25
50
75
100
125
150
175
200
225
250
275
300
325
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90 100 110
60
65
70
75
20 hp
5 hp
10 hp
7.5 hp
15 hp
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Met
ers
Fee
t
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Model 375ST6 Performance
Dimension Information
P
M
MD
5.88
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
5 1 A 6” 21.57 22.90 5.38 101 53
7.5 2 B 6” 26.32 24.20 5.38 108 65
10 2 A 6” 26.32 25.40 5.38 116 65
15 4 B 6” 35.82 28.00 5.38 129 89
20 5 1A, 4B 6” 40.57 30.56 5.38 135 101
Mi8073
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Submersible Turbine Pumps
Model 375ST6 Performance PAGE: SP-247DATE: Mar 1, 2009
10 GPM
10 F
T
0 50 100 150 200 250 300 350 400 450 500100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
40
60
80
100
120
140
160
180
200
220
240
260
280
300
0 10 20 30 40 50 60 70 80 90 100 110
55
60
65
70
75
60 hp
25 hp
40 hp
30 hp
50 hp
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
3450 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68°F -6" motor / 3450 rpm
Submersible Turbine Pumps
Dimension Information
P
M
MD
5.88
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
25 6 3A, 3B 6” 45.27 33.13 5.38 148 113
30 7 5A, 2B 6” 50.02 35.69 5.38 162 125
40 9 A 6” 59.57 40.81 5.38 195 149
50 11 A 6” 69.07 57.83 5.38 310 172
60 13 A 6” 78.57 63.83 5.38 340 196
Model 375ST6 Performance
Mi8074
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
Specifi cationsMinimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT
Maximum Working Pressure Standard: 350 psiDouble Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Model 375ST6 Performance PAGE: SP-249DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. Effi ciency correction required for low stage count (1 stage-7%, 2 stage-4%, 3 stage-1%) Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor. Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
Trim A Diameter C AngleA 4.688” 35 °
B 4.440” 35 °
C 4.313” 35 °
Impeller DimensionsA
C
Mi8075
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
10 GPM
1 F
T
0 50 100 150 200 250 300 350 400 450
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
-4
-2
0
2
4
6
8
10
12
14
16
18
20
22
0 10 20 30 40 50 60 70 80 90 100 110
2.00
3.00
4.00
5.00
Trim C
Trim B
Trim A
Trim C
Trim B
68%
72%
60%
64%
64%
68%
60%
Trim A
1.52.02.53.03.5
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Turbine Pumps
Model Number ExplanationExample: 225ST25D8B-0366 225 = GPM ST = Sub Turbine 25 = Horsepower D = Ductile Iron 8 = 8” Pump B = Impeller Trim 03 = Number of stages 6 = Motor Size 6 = Discharge Size
Features:■ 100% Franklin factory tested.
■ Ductile iron discharge and suction bracket.
■ Ductile iron bowls bolt together for easy service.
■ Epoxy coated bowls for improved effi ciency.
■ Stainless upthrust bolt provides exceptional upthrust protection.
■ Bronze discharge bearing is grease packed for maximum bearing protection.
■ Fluted rubber bearings in all bowls.
■ Suction inlet located above bottom bearing prevents abrasives from entering the bearing.
■ Suction bracket design allows easy access to coupling.
■ Bronze bracket bearing is protected with stainless steel sand collar.
■ Stainless steel impellers with stainless steel taper lock secures impeller to shaft.
■ Stainless steel pump shaft for increased durability.
■ Shaft coupling is keyed to pump by set screws and is splined to fi t motor shaft.
8” Submersible Turbine Pump225 to 1000 GPM
PAGE: SP-250DATE: Mar 1, 2009
Submersible Turbine Pumps
8” Submersible Turbine PumpOrdering Information
8” 60 Hz Submersible Turbine Pump Ends
GPM HP Stages Trim Size Motor Bracket Size
Discharge Size Order No. Model No. Weight
225
7.5 1 A 6” 4” NPT 96080225000 225ST7D8A-0164 1366” NPT 96080225100 225ST7D8A-0166 145
15 2 A 6” 4” NPT 96080225001 225ST15D8A-0264 1716” NPT 96080225101 225ST15D8A-0266 180
20 3 A 6” 4” NPT 96080225002 225ST20D8A-0364 2066” NPT 96080225102 225ST20D8A-0366 215
25 4 B 6” 4” NPT 96080225003 225ST25D8B-0464 2426” NPT 96080225103 225ST25D8B-0466 250
30 5 B 6” 4” NPT 96080225004 225ST30D8B-0564 2776” NPT 96080225104 225ST30D8B-0566 285
40 6 B 6” 4” NPT 96080225005 225ST40D8B-0664 3126” NPT 96080225105 225ST40D8B-0666 321
50 8 B 6” 4” NPT 96080225006 225ST50D8B-0864 3826” NPT 96080225106 225ST50D8B-0866 391
60 10 B 6” 4” NPT 96080225007 225ST60D8B-1064 4536” NPT 96080225107 225ST60D8B-1066 461
75 12 B 8” 4” NPT 96080225203 225ST75D8B-1284 5466” NPT 96080225303 225ST75D8B-1286 554
100 16 B 8” 4” NPT 96080225204 225ST100D8B-1684 6866” NPT 96080225304 225ST100D8B-1686 695
125 18 A 8” 4” NPT 96080225205 225ST125D8A-1884 7576” NPT 96080225305 225ST125D8A-1886 765
275
10 1 A 6” 4” NPT 96080275000 275ST10D8A-0164 1366” NPT 96080275100 275ST10D8A-0166 145
20 2 A 6” 4” NPT 96080275001 275ST20D8A-0264 1716” NPT 96080275101 275ST20D8A-0266 180
30 3 A 6” 4” NPT 96080275002 275ST30D8A-0364 2066” NPT 96080275102 275ST30D8A-0366 215
40 4 A 6” 4” NPT 96080275003 275ST40D8A-0464 2426” NPT 96080275103 275ST40D8A-0466 250
50 5 A 6” 4” NPT 96080275004 275ST50D8A-0564 2776” NPT 96080275104 275ST50D8A-0566 285
60 6 A 6” 4” NPT 96080275005 275ST60D8A-0664 3126” NPT 96080275105 275ST60D8A-0666 321
75 8 B 8” 4” NPT 96080275203 275ST75D8B-0864 4056” NPT 96080275303 275ST75D8B-0866 413
100 10 B 8” 4” NPT 96080275204 275ST100D8B-1084 4756” NPT 96080275304 275ST100D8B-1086 483
125 14 B 8” 4” NPT 96080275205 275ST125D8B-1484 6166” NPT 96080275305 275ST125D8B-1486 625
350
7.5 1 B 6” 4” NPT 96080350000 350ST7D8B-0164 1306” NPT 96080350100 350ST7D8B-0166 138
10 1 A 6” 4” NPT 96080350001 350ST10D8A-0164 1306” NPT 96080350101 350ST10D8A-0166 138
15 2 B 6” 4” NPT 96080350002 350ST15D8B-0264 1626” NPT 96080350102 350ST15D8B-0266 170
20 3 B 6” 4” NPT 96080350004 350ST20D8B-0364 1936” NPT 96080350104 350ST20D8B-0366 202
30 3 A 6” 4” NPT 96080350005 350ST30D8A-0364 1936” NPT 96080350105 350ST30D8A-0366 202
40 6 B 6” 4” NPT 96080350008 350ST40D8B-0664 2896” NPT 96080350108 350ST40D8B-0666 298
50 7 B 6” 4” NPT 96080350010 350ST50D8B-0766 3216” NPT 96080350110 350ST50D8B-0764 330
60 9 B 6” 4” NPT 96080350012 350ST60D8B-0964 3856” NPT 96080350112 350ST60D8B-0966 393
75 11 B 8” 4” NPT 96080350207 350ST75D8B-1184 4716” NPT 96080350307 350ST75D8B-1186 479
100 11 A 8” 4” NPT 96080350208 350ST100D8A-1184 4716” NPT 96080350308 350ST100D8A-1186 479
125 13 A 8” 4” NPT 96080350210 350ST125D8A-1384 5356” NPT 96080350310 350ST125D8A-1386 543
Mi8020
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Submersible Turbine Pumps
Mi8021400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
8” Submersible Turbine PumpOrdering Information
8” 60 Hz Submersible Turbine Pump Ends
GPM HP Stages Trim Size Motor Bracket Size
Discharge Size Order No. Model No. Weight
450
15 1 B 6” 4” NPT 96080450000 450ST15D8B-0164 1306” NPT 96080450100 450ST15D8B-0166 138
20 1 A 6” 4” NPT 96080450001 450ST20D8A-0164 1306” NPT 96080450101 450ST20D8A-0166 138
25 2 B 6” 4” NPT 96080450002 450ST25D8B-0264 1626” NPT 96080450102 450ST25D8B-0266 170
40 3 B 6” 4” NPT 96080450003 450ST40D8B-0364 1936” NPT 96080450103 450ST40D8B-0366 202
50 3 A 6” 4” NPT 96080450004 450ST50D8A-0364 1936” NPT 96080450104 450ST50D8A-0366 202
60 5 B 6” 4” NPT 96080450005 450ST60D8B-0564 2576” NPT 96080450105 450ST60D8B-0566 266
75 6 B 8” 4” NPT 96080450203 450ST75D8B-0684 3116” NPT 96080450303 450ST75D8B-0686 320
100 8 B 8” 4” NPT 96080450204 450ST100D8B-0884 3756” NPT 96080450304 450ST100D8B-0886 384
125 10 B 8” 4” NPT 96080450205 450ST125D8B-1084 4396” NPT 96080450305 450ST125D8B-1086 448
550
10 1 B 6” 4” NPT 96080550000 550ST10D8B-0164 1376” NPT 96080550100 550ST10D8B-0166 146
20 2 B 6” 4” NPT 96080550002 550ST20D8B-0264 1726” NPT 96080550102 550ST20D8B-0266 181
30 3 B 6” 4” NPT 96080550004 550ST30D8B-0364 2086” NPT 96080550104 550ST30D8B-0366 217
40 4 B 6” 4” NPT 96080550006 550ST40D8B-0464 2436” NPT 96080550106 550ST40D8B-0466 252
50 4 A 6” 4” NPT 96080550007 550ST50D8A-0464 2436” NPT 96080550107 550ST50D8A-0466 252
60 6 B 6” 4” NPT 96080550009 550ST60D8B-0664 3146” NPT 96080550109 550ST60D8B-0666 323
75 6 A 8” 4” NPT 96080550205 550ST75D8A-0684 3376” NPT 96080550305 550ST75D8A-0686 345
100 8 A 8” 4” NPT 96080550207 550ST100D8A-0884 4086” NPT 96080550307 550ST100D8A-0886 416
125 10 A 8” 4” NPT 96080550209 550ST125D8A-1084 4796” NPT 96080550309 550ST125D8A-1086 487
700
20 1 A 6” 4” NPT 96080700000 700ST20D8A-0164 1376” NPT 96080700100 700ST20D8A-0166 146
40 2 A 6” 4” NPT 96080700001 700ST40D8A-0264 1726” NPT 96080700101 700ST40D8A-0266 181
50 3 B 6” 4” NPT 96080700002 700ST50D8B-0364 2086” NPT 96080700102 700ST50D8B-0366 217
60 3 A 6” 4” NPT 96080700003 700ST60D8A-0364 2086” NPT 96080700103 700ST60D8A-0366 217
75 4 B 6” 4” NPT 96080700203 700ST75D8B-0484 2666” NPT 96080700303 700ST75D8B-0486 274
100 6 B 8” 4” NPT 96080700205 700ST100D8B-0684 3376” NPT 96080700305 700ST100D8B-0686 345
125 7 B 8” 4” NPT 96080700206 700ST125D8B-0784 3726” NPT 96080700306 700ST125D8B-0786 381
25 1 B 6” 6” NPT 96081000100 1000ST25D8B-0166 94
30 1 A 6” 6” NPT 96081000101 1000ST30D8A-0166 94
40 2 B6” 6” NPT 96081000102 1000ST40D8B-0266 123
8” 6” NPT 96081000300 1000ST40D8B-0286 143
50 2 A6” 6” NPT 96081000103 1000ST50D8A-0266 123
8” 6” NPT 96081000301 1000ST50D8A-0286 143
1000* 60 3 1A 2B6” 6” NPT 96081000104 1000ST60D8X-0366 151
8” 6” NPT 96081000302 1000ST60D8X-0386 172
75 4 B 8” 6” NPT 96081000303 1000ST75D8B-0486 200
100 4 A 8” 6” NPT 96081000304 1000ST100D8A-0486 200
125 6 5A 1B 8” 6” NPT 96081000305 1000ST125D8X-0686 258
150 7 A 8” 6” NPT 96081000306 1000ST150D8A-0786 286
175 8 A 8” 6” NPT 96081000307 1000ST175D8A-0886 315
200 9 A 8” 6” NPT 96081000308 1000ST200D8A-0986 343
PAGE: SP-255DATE: Mar 1, 2009
Note: 40-60 hp 8” motor bracket adapter option available* Minimum Well ID: 10”
Submersible Turbine Pumps
Model 225ST8 Performance PAGE: SP-260DATE: Sept 1, 2007
40 hp
30 hp
25 hp
20 hp
15 hp
7.5 hp
0
100
200
300
400
500
600
700
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
0 25 50 75 100 125 150 175 200 225 250 275 300 325
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%
40%
45%
50%
55%
60%
65%
70%
75%
HP Stages Trim Motor Size
Disch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
7.5 1 A 6” 4” 26 24 5.38 110 1366” 26 24 5.38 110 145
15 2 A 6” 4” 31 28 5.38 131 1716” 31 28 5.38 131 180
20 3 A 6” 4” 37 31 5.38 147 2066” 37 31 5.38 147 215
25 4 B 6”4” 42 33 5.38 158 2426” 42 33 5.38 158 250
30 5 B 6” 4” 48 36 5.38 176 2776” 48 36 5.38 176 285
40 6 B 6” 4” 53 41 5.38 206 3126” 53 41 5.38 206 321
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 225ST8 Performance
Mi8022
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
0 25 50 75 100 125 150 175 200 225 250 275 300 32536%
40%
44%
48%
52%
56%
60%
64%
68%
72%
76%
125 hp
100 hp
75 hp
60 hp
50 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%
HP Stages Trim Motor Size
Disch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
50 8 B 6” 4” 64 55 5.38 304 3826” 64 55 5.38 304 391
60 10 B 6” 4” 75 61 5.38 334 4536” 75 61 5.38 334 461
75 12 B 8” 4” 88 47 7.70 430 5466” 88 47 7.70 430 554
100 16 B 8”4” 110 55 7.70 530 6866” 110 55 7.70 530 695
125 18 A 8” 4” 121 69 7.70 700 7576” 121 69 7.70 700 765
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 225ST8 Performance
Trim D Diameter E Diameter F AngleA 5.705 5.400 20 o
B 5.561 5.250 20 o
C 5.083 4.750 20 o
Impeller Dimensions
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
DE
F
Mi8023
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Note: Effi ciencies are typical, not guaranteed. Effi ciency derate for low stage count pumps- 1 stage-2%, 2 stage-1% Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor. Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
PO
WE
R (
hp)
0
10
20
30
40
50
60
70
80
90
100
110
120
130
0 40 80 120 160 200 240 280 320 3600.0
2.5
5.0
7.5
10.0
12.5
15.0
17.5
20.0
22.5
25.0
27.5
30.0
32.5
Trim A
Trim B
Trim C
Trim A
Trim B
Trim C
68%71%
73%74%
75%74%
73%
72%70%
PAGE: SP-265DATE: Sept 1, 2007
Nominal RPM: 3520
Submersible Turbine Pumps
Model 275ST8 Performance PAGE: SP-270DATE: Sept 1, 2007
0
50
100
150
200
250
300
350
400
450
500
550
600
650
0 50 100 150 200 250 300 350 40015%
20%
25%
30%
35%
40%
45%
50%
55%
60%
65%
70%
75%
80%
50 hp
40 hp
30 hp
20 hp
10 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%
HP Stages Trim Motor Size
Disch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
10 1 A 6” 4” 26 25 5.38 118 1366” 26 25 5.38 118 145
20 2 A 6” 4” 31 31 5.38 147 1716” 31 31 5.38 147 180
30 3 A 6” 4” 37 36 5.38 176 2066” 37 36 5.38 176 215
40 4 A 6”4” 42 41 5.38 206 2426” 42 41 5.38 206 250
50 5 A 6” 4” 48 55 5.38 304 2776” 48 55 5.38 304 285
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 275ST8 Performance
Mi8024400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
0 50 100 150 200 250 300 350 40020%
25%
30%
35%
40%
45%
50%
55%
60%
65%
70%
75%
80%
125 hp
100 hp
75 hp
60 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%HP Stages Trim Motor
SizeDisch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
60 6 A 6” 4” 53 61 5.38 334 3126” 53 61 5.38 334 321
75 8 B 8” 4” 65 47 7.70 430 4056” 65 47 7.70 430 413
100 10 B 8” 4” 76 55 7.70 530 4756” 76 55 7.70 530 483
125 14 B 8”4” 99 69 7.70 700 6166” 99 69 7.70 700 625
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 275ST8 Performance
Trim D Diameter E Diameter F AngleA 5.705 5.400 20 o
B 5.562 5.250 20 o
C 5.084 4.750 20 o
Impeller Dimensions
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
DE
F
Mi8025
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Note: Effi ciencies are typical, not guaranteed. Effi ciency derate for low stage count pumps- 1 stage-2%, 2 stage-1% Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor. Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
0
10
20
30
40
50
60
70
80
90
100
110
120
130
0 50 100 150 200 250 300 350 400 4500.0
2.5
5.0
7.5
10.0
12.5
15.0
17.5
20.0
22.5
25.0
27.5
30.0
32.5
Trim A
Trim B
Trim C
Trim A
Trim B
Trim C
68% 70%72%
74%
75%
74%
72%
70%69%
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
PO
WE
R (
hp)
PAGE: SP-275DATE: Sept 1, 2007
Nominal RPM: 3520
Submersible Turbine Pumps
Model 350ST8 Performance PAGE: SP-280DATE: Sept 1, 2007
0
25
50
75
100
125
150
175
200
225
250
275
300
325
350
375
400
0 50 100 150 200 250 300 350 400 450 5000%
5%
10%
15%
20%
25%
30%
35%
40%
45%
50%
55%
60%
65%
70%
75%
80%
30 hp
20 hp
15 hp
10 hp
7.5 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%
HP Stages Trim Motor Size
Disch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
7.5 1 B 6” 4” 26 24 5.38 110 1306” 26 24 5.38 110 138
10 1 A 6” 4” 26 25 5.38 118 1306” 26 25 5.38 118 138
15 2 B 6” 4” 33 28 5.38 131 1616” 33 28 5.38 131 170
20 3 B 6”4” 39 31 5.38 147 1936” 39 31 5.38 147 202
30 3 A 6” 4” 39 36 5.38 176 1936” 39 36 5.38 176 202
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 350ST8 Performance
Mi8026400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
200
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
0 50 100 150 200 250 300 350 400 450 5005%
10%
15%
20%
25%
30%
35%
40%
45%
50%
55%
60%
65%
70%
75%
80%
125 hp
100 hp
75 hp
60 hp
50 hp
40 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%
HP Stages Trim Motor Size
Disch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
40 6 B 6” 4” 58 41 5.38 206 2896” 58 41 5.38 206 298
50 7 B 6” 4” 65 55 5.38 304 3216” 65 55 5.38 304 329
60 9 B 6” 4” 77 61 5.38 334 3856” 77 61 5.38 334 393
75 11 B 8” 4” 92 47 7.70 430 4716” 92 47 7.70 430 479
100 11 A 8” 4” 92 55 7.70 530 4716” 92 55 7.70 530 479
125 13 A 8” 4” 104 69 7.70 700 5346” 104 69 7.70 700 543
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 350ST8 Performance
Trim D Diameter E Diameter F AngleA 5.701 5.250 20 o
B 5.229 4.750 20 o
C 4.757 4.250 20 o
Impeller Dimensions
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
DE
F
Mi8027
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Note: Effi ciencies are typical, not guaranteed. Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor. Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
0 50 100 150 200 250 300 350 400 450 5000.0
5.0
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
50.0
55.0
60.0
65.0
70.0
Trim A
Trim B
Trim C
68%73%
77%
75%
78%
77%
76%
74%
72%
Trim A
Trim B
Trim C
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
PO
WE
R (
hp)
PAGE: SP-285DATE: Sept 1, 2007
Nominal RPM: 3520
Submersible Turbine Pumps
Model 450ST8 Performance PAGE: SP-290DATE: Sept 1, 2007
0
50
100
150
200
250
300
350
400
450
0 100 200 300 400 500 600
-10%
0%
10%
20%
30%
40%
50%
60%
70%
80%
50 hp
40 hp
25 hp
20 hp
15 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%
HP Stages Trim Motor Size
Disch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
15 1 B 6” 4” 26 28 5.38 131 1306” 26 28 5.38 131 138
20 1 A 6” 4” 26 31 5.38 147 1306” 26 31 5.38 147 138
25 2 B 6” 4” 33 33 5.38 156 1616” 33 33 5.38 156 170
40 3 B 6”4” 39 41 5.38 206 1936” 39 41 5.38 206 202
50 3 A 6” 4” 39 55 5.38 304 1936” 39 55 5.38 304 202
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 450ST8 Performance
Mi8028400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
200
300
400
500
600
700
800
900
1000
1100
0 100 200 300 400 500 600-10%
0%
10%
20%
30%
40%
50%
60%
70%
80%
125 hp
100 hp
75 hp
60 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%HP Stages Trim Motor
SizeDisch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
60 5 B 6” 4” 52 61 5.38 334 2576” 52 61 5.38 334 266
75 6 B 8” 4” 60 47 7.7 430 3116” 60 47 7.7 430 320
100 8 B 8” 4” 72 55 7.7 530 3756” 72 55 7.7 530 384
125 10 B 8” 4” 85 69 7.7 700 4396” 85 69 7.7 700 447
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 450ST8 Performance
Trim D Diameter E Diameter F AngleA 5.720 5.287 20 o
B 5.302 4.842 20 o
C 4.835 4.349 20 o
Impeller Dimensions
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
DE
F
Mi8029
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Note: Effi ciencies are typical, not guaranteed. Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor. Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
0 100 200 300 400 500 6000.0
5.0
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
50.0
55.0
60.0
65.0
70.0
Trim A
Trim B
Trim C
Trim A
Trim B
Trim C
70% 72% 75% 76%
77%
76%75%
72%
70%
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
PO
WE
R (
hp)
PAGE: SP-295DATE: Sept 1, 2007
Nominal RPM: 3520
Submersible Turbine Pumps
Model 550ST8 Performance PAGE: SP-300DATE: Sept 1, 2007
0
50
100
150
200
250
300
350
400
450
500
0 100 200 300 400 500 600 700 800-20%
-10%
0%
10%
20%
30%
40%
50%
60%
70%
80%
50 hp
40 hp
30 hp
20 hp
10 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%
HP Stages Trim Motor Size
Disch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
10 1 B 6” 4” 27 25 5.38 118 1376” 27 25 5.38 118 146
20 2 B 6” 4” 34 31 5.38 147 1726” 34 31 5.38 147 181
30 3 B 6” 4” 41 36 5.38 176 2086” 41 36 5.38 176 217
40 4 B 6”4” 48 41 5.38 206 2436” 48 41 5.38 206 252
50 4 A 6” 4” 48 55 5.38 304 2436” 48 55 5.38 304 252
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 550ST8 Performance
Mi8030400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
200
300
400
500
600
700
800
900
1000
1100
1200
1300
0 100 200 300 400 500 600 700 800-30%
-20%
-10%
0%
10%
20%
30%
40%
50%
60%
70%
80%
125 hp
100 hp
75 hp
60 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%HP Stages Trim Motor
SizeDisch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
60 6 B 6” 4” 63 61 5.38 334 3146” 63 61 5.38 334 323
75 6 A 8” 4” 64 47 7.70 430 3376” 64 47 7.70 430 345
100 8 B 8” 4” 78 55 7.70 530 4086” 78 55 7.70 530 416
125 10 B 8” 4” 92 69 7.70 700 4796” 92 69 7.70 700 487
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 550ST8 Performance
Trim D Diameter E Diameter F AngleA 5.674 5.000 17 o
B 5.371 4.661 17 o
C 5.227 4.500 17 o
Impeller Dimensions
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
DE
F
Mi8031
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Note: Effi ciencies are typical, not guaranteed. Effi ciency derate for low stage count pumps- 1 stage-3%, 2 stage-2%, 3 stage-3% Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor. Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
0
10
20
30
40
50
60
70
80
90
100
110
120
0 100 200 300 400 500 600 700 8000.0
5.0
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
50.0
55.0
60.0
Trim A
Trim B
Trim C
68%
Trim A
Trim B
Trim C
71%73%
75%
75%
76% 73%
71%
68%
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
PO
WE
R (
hp)
PAGE: SP-305DATE: Sept 1, 2007
Nominal RPM: 3520
Submersible Turbine Pumps
Model 700ST8 Performance PAGE: SP-310DATE: Sept 1, 2007
0
50
100
150
200
250
300
350
400
450
500
550
600
650
700
750
0 100 200 300 400 500 600 700 800 9005%
10%
15%
20%
25%
30%
35%
40%
45%
50%
55%
60%
65%
70%
75%
80%
125 hp
100 hp
75 hp
60 hp
50 hp
40 hp
20 hp
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
EF
FIC
IEN
CY
%
HP Stages Trim Motor Size
Disch. Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
20 1 A 6” 4” 27 31 5.38 147 1376” 27 31 5.38 147 146
40 2 A 6” 4” 34 41 5.38 206 1726” 34 41 5.38 206 181
50 3 B 6” 4” 41 55 5.38 176 2086” 41 55 5.38 176 217
60 3 A 6” 4” 41 61 5.38 334 2086” 41 61 5.38 334 217
75 4 B 8” 4” 50 47 7.70 430 2666” 50 47 7.70 430 274
100 6 B 8” 4” 64 55 7.70 530 3376” 64 55 7.70 530 345
125 7 B 8” 4” 71 69 7.70 700 3726” 71 69 7.70 700 381
Dimension Information
P
M
MD
7.6
Specifi cationsMinimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Nominal RPM: 3520Based on Fresh Water @ 68 oF.Maximum Working Pressure: Standard (600 psi) Double Bolted (950 psi)
Submersible Turbine Pumps
Model 700ST8 Performance
Trim D Diameter E Diameter F AngleA 5.672 4.980 17 o
B 5.451 4.742 17 o
C 5.225 4.500 17 o
Impeller Dimensions
Part Name Common Material Name Material Spec NumberDischarge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Materials of Construction
DE
F
Mi8032
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Note: Effi ciencies are typical, not guaranteed. Effi ciency derate for low stage count pumps- 1 stage-3%, 2 stage-2%, 3 stage-1% Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor. Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
0
10
20
30
40
50
60
70
80
90
100
110
120
0 100 200 300 400 500 600 700 800 900 10000.0
5.0
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
50.0
55.0
60.0
Trim A
Trim B
Trim C 69%
Trim A
Trim B
Trim C
72% 74%
75%
75%
76%
74%73%
71%
TO
TA
L D
YN
AM
IC H
EA
D -
FE
ET
FLOWRATE - U.S. GALLONS PER MINUTE
PO
WE
R (
hp)
Nominal RPM: 3520
Submersible Turbine Pumps
Model 1000ST8 Performance PAGE: SP-315DATE: Mar 1, 2009
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 13000
25
50
75
100
125
150
175
200
225
250
275
300
325
350
375
400
425
0
20
40
60
80
100
120
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280
55
60
65
70
75
75 hp
60 hp
50 hp
40 hp
30 hp
25 hp
3525 rpm3450 rpm
20 GPM5
FT
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68 °F -6" motor / 3450 rpm, 25-60 hp -8" motor / 3525 rpm, 75-200 hp
Submersible Turbine Pumps
Model 1000ST8 Performance
Dimension Information
P
M
MD
8.00
Specifi cationsMinimum Well I.D. 10”
Bowl Diameter (without cable guard) 7.75”
Minimum Submergence Above Inlet 50 Feet
Discharge 6” NPT
Maximum Working Pressure Standard: 350 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
25 1 B 6” 28.63 33 5.38 156 94
30 1 A 6” 28.63 36 5.38 174 94
40 2 B 6” 36.00 41 5.38 206 1232 B 8” 37.38 36 7.70 320 143
50 2 A 6” 36.00 55 5.38 300 1232 A 8” 37.38 39 7.70 345 143
60 3 1A 2B 6” 43.38 61 5.38 330 1513 1A 2B 8” 44.76 42 7.70 375 172
75 4 B 8” 52.13 47 7.70 430 200
Mi8033
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Materials of ConstructionPart Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Submersible Turbine Pumps
Model 1000ST8 Performance PAGE: SP-320DATE: Mar 1, 2009
Met
ers
Fee
t
Effi
cien
cy (
%)
US GPM
M3PH
20 GPM
20 F
T
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300100
200
300
400
500
600
700
800
900
1000
1100
50
100
150
200
250
300
350
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280
55
60
65
70
75
200 hp
175 hp
150 hp
125 hp
100 hp
3525 rpm
Recommended operating range
------- Alternate pump selection available
Note: Performance based on: -Fresh water, 68 °F -8" motor / 3525 rpm, 75-200 hp
Submersible Turbine Pumps
Model 1000ST8 Performance
Mi8034
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Dimension Information
P
M
MD
8.00
Specifi cationsMinimum Well I.D. 10”
Bowl Diameter (without cable guard) 7.75”
Minimum Submergence Above Inlet 50 Feet
Discharge 6” NPT
Maximum Working Pressure Standard: 350 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
HP Stages Trim Motor Size
P M* MD* Motor Wt Pump WtInches Inches Inches Lbs. Lbs.
100 4 A 8” 52.13 55 7.70 530 200
125 6 5A 1B 8” 66.89 69 7.70 700 258
150 7 A 8” 74.26 78 7.70 840 286
175 8 A 8” 81.64 86 7.70 925 315
200 9 A 8” 89.02 95 7.70 1040 343
Materials of ConstructionPart Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
Submersible Turbine Pumps
Model 1000ST8 Performance PAGE: SP-325DATE: Mar 1, 2009
Note: Effi ciencies are typical, not guaranteed. Effi ciency derate for low stage count pumps: 1 stage-4%, 2 stage-2% Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Nominal RPM: 3525
Mi8055
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
Single Stage Performance
Trim D Diameter E Diameter F AngleA 5.716 5.039 11 o
B 5.716 4.377 21 o
Impeller DimensionsDE
F
20 GPM
2 F
T
600 700 800 900 1000 1100 1200
0
10
20
30
40
50
60
70
80
90
- 5
0
5
10
15
20
25
1 5 0 17 5 2 0 0 2 2 5 2 5 0 27 5
16.0
20.0
24.0
28.0
12
14
16
18
20
Trim A
Trim B
Trim A
Trim B
66% 68% 70%
74%72%
72%
70%68%
66%
Met
ers
Fee
t
US GPM
M3PH
Pow
er (
hp)
Pow
er (
kW)
Submersible Pumps
Model Number ExplanationExample: 150SR10F6A-0443 150 = Gallons per Minute SR = Series 10 = Horsepower F = Stainless 6 = 6” Pump A = Impeller Trim 04 = Number of Stages 4 = 4” Motor 3 = 3” Discharge
Features:■ Stainless steel impellers and diffusers to resist corrosion.
■ Heavy duty stainless steel shell assures permanent alignment of all components to increase longevity and enables higher pressures than strap designs.
■ Tefl on® fl oating wear ring, ceramic bearing journal and Nitrile rubber fl uted bearing ensure durability against wear for long-lasting performance and reliability.
■ Suited to operate in horizontal position.
■ Built-in check valve to protect the pump against water hammer.
■ Energy effi cient hydraulic design for cost effective operation.
■ Space-saving compact design.
■ Easy to install and dismantle for service in the fi eld if necessary.
Stainless Steel Submersible Pumps100 to 475 GPM
PAGE: SP-120DATE: July 1, 2008
Designed for industrial and agricultural applications, the SR Series submersible pump utilizes high grade stainless steel materials for the most demanding applications.
■ 6” to 300 gpm
■ 8” to 475 gpm
Submersible Pumps
6” & 8” Stainless Steel Submersible PumpsOrdering Information
Mi8035
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
6" PUMP ENDS
GPM HP Stages Motor Size Model No. Order No. Dimensions
(inches)Weight
(lbs)
100
5 3 4” 100SR5F6A-0343 96160100001 12.5 207.5 5 4” 100SR7F6A-0543 96160100002 15.5 2410 6 4” 100SR10F6A-0643 96160100003 17.0 2710 7 4” 100SR10F6A-0743 96160100004 18.4 2815 9 6” 100SR15F6A-0963 96160100005 21.4 3115 11 6” 100SR15F6A-1163 96160100006 24.4 3520 13 6” 100SR20F6A-1363 96160100007 27.3 3920 15 6” 100SR20F6A-1563 96160100008 30.3 4225 18 6” 100SR25F6A-1863 96160100009 35.2 4730 22 6” 100SR30F6A-2263 96160100010 40.6 5540 26 6” 100SR40F6A-2663 96160100011 46.5 6240 28 6” 100SR40F6A-2863 96160100012 49.4 66
150
7.5 3 4” 150SR7F6A-0343 96160150001 14.4 2310 4 4” 150SR10F6A-0443 96160150002 16.2 2515 5 6” 150SR15F6A-0563 96160150003 18.0 2815 7 6” 150SR15F6A-0763 96160150004 21.7 3220 9 6” 150SR20F6A-0963 96160150005 25.3 3625 11 6” 150SR25F6A-1163 96160150006 29.0 4130 14 6” 150SR30F6A-1463 96160150007 34.5 4740 15 6” 150SR40F6A-1563 96160150008 36.8 4940 19 6” 150SR40F6A-1963 96160150009 43.7 5750 23 6” 150SR50F6A-2363 96160150010 51.0 66
240
7.5 2 4” 240SR7F6A-0243 96160240001 14.4 2410 3 4” 240SR10F6A-0343 96160240002 18.1 3015 4 6” 240SR15F6A-0463 96160240003 21.7 3520 5 6” 240SR20F6A-0563 96160240004 25.3 4020 6 6” 240SR20F6A-0663 96160240005 29.0 4525 7 6” 240SR25F6A-0763 96160240006 32.6 5030 9 6” 240SR30F6A-0963 96160240007 39.9 6040 10 6” 240SR40F6A-1063 96160240008 43.6 6540 12 6” 240SR40F6A-1263 96160240009 50.9 7550 15 6” 240SR50F6A-1563 96160240010 61.9 90
300
7.5 2 4” 300SR7F6A-0243 96160300001 14.4 2510 3 4” 300SR10F6A-0343 96160300002 18.0 3015 4 6” 300SR15F6A-0463 96160300003 21.7 3520 5 6” 300SR20F6A-0563 96160300004 25.3 4020 6 6” 300SR20F6A-0663 96160300005 29.0 4525 7 6” 300SR25F6A-0763 96160300006 32.6 5130 8 6” 300SR30F6A-0864 96160300007 36.3 5530 9 6” 300SR30F6A-0964 96160300008 39.9 6040 10 6” 300SR40F6A-1064 96160300009 43.6 6640 12 6” 300SR40F6A-1264 96160300010 50.9 7550 14 6” 300SR50F6A-1464 96160300011 58.2 8650 15 6” 300SR50F6A-1564 96160300012 61.9 90
8" PUMP ENDS
GPM HP Stages Motor Size Model No. Order No. Dimensions
(inches)Weight
(lbs)
400
15 2 6” 400SR15F8A-0264 96180400001 25.3 6925 3 6” 400SR25F8A-0364 96180400002 30.3 8130 4 6” 400SR30F8A-0464 96180400003 35.2 9240 5 6” 400SR40F8A-0564 96180400004 40.2 10350 7 6” 400SR50F8A-0764 96180400006 50.1 12460 8 6” 400SR60F8A-0864 96180400007 55.0 13575 10 8” 400SR75F8A-1084 96180400009 65.1 157
100 13 8” 400SR100F8A-1384 96180400012 80.0 192
475
30 3 6” 475SR30F8A-0366 96180475002 30.3 8140 4 6” 475SR40F8A-0466 96180475003 35.2 9250 6 6” 475SR50F8A-0666 96180475005 45.1 11260 7 6” 475SR60F8A-0766 96180475006 50.1 12475 8 8” 475SR75F8A-0886 96180475007 55.2 138
100 10 8” 475SR100F8A-1086 96180475009 65.1 159125 13 8” 475SR125F8A-1386 96180475012 80.0 192
Submersible Pumps
6” Stainless Steel Submersible Pumps100 GPM Performance Curve
PAGE: SP-125DATE: July 1, 2008
ME
TE
RS
FE
ET
M3PH
GPM
EF
FIC
IEN
CY
%
0
200
150
100
50
0 3520 25 3015105
7.5 hp
10 hp
10 hp
15 hp
15 hp
0 20 40 60 80 100 120 1400
200
400
600
80070
60
50
40
5 hp
Submersible Pumps
6” Stainless Steel Submersible Pumps100 GPM Specifi cations
Mi8036
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
D
P
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
5 3 3” 4” 5.55” 12.5” 207.5 5 3” 4” 5.55” 15.5” 2410 6 3” 4” 5.55” 17.0” 2710 7 3” 4” 5.55” 18.4” 2815 9 3” 6” 5.67” 21.4” 3115 11 3” 6” 5.67” 24.4” 35
Dimension Information
*Note: D = Discharge, P = Pump Length
Parts DescriptionMaterial
Type AISIOuter case with motor adapter Stainless Steel 304Discharge head with built-in check valve Stainless Steel 304Sealing O-ring Nitrile Rubber (NBR) N/AUpper bowl Stainless Steel 304Upper bearing bushing Nitrile Rubber (NBR) N/A
Upper journal sleeve Stainless Steel w/ ceramic coating 329
Pump shaft Stainless Steel 431Motor coupling Stainless Steel 431/329Diffuser Stainless Steel 304Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/ASecondary journal sleeve Stainless Steel 304Impeller Stainless Steel 304Cable guard Stainless Steel 316Suction strainer Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 316Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
Submersible Pumps
6” Stainless Steel Submersible Pumps100 GPM Performance Curve
PAGE: SP-130DATE: July 1, 2008
0
400
450
350
300
250
200
150
100
50
0 3520 25 3015105
20 hp
20 hp
25 hp
30 hp
40 hp
40 hp
0 20 40 60 80 100 120 1400
200
400
600
800
1000
1200
1400
1600
ME
TE
RS
FE
ET
M3PH
GPM
70
60
50
40 EF
FIC
IEN
CY
%
Submersible Pumps
6” Stainless Steel Submersible Pumps100 GPM Specifi cations
Mi8037
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
D
P
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
20 13 3” 6” 5.67” 27.3” 3920 15 3” 6” 5.67” 30.3” 4225 18 3” 6” 5.67” 35.2” 4730 22 3” 6” 5.67” 40.6” 5540 26 3” 6” 5.67” 46.5” 6240 28 3” 6” 5.67” 49.4” 66
Dimension Information
*Note: D = Discharge, P = Pump Length
Parts DescriptionMaterial
Type AISIOuter case with motor adapter Stainless Steel 304Discharge head with built-in check valve Stainless Steel 304Sealing O-ring Nitrile Rubber (NBR) N/AUpper bowl Stainless Steel 304Upper bearing bushing Nitrile Rubber (NBR) N/A
Upper journal sleeve Stainless Steel w/ ceramic coating 329
Pump shaft Stainless Steel 431Motor coupling Stainless Steel 431/329Diffuser Stainless Steel 304Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/ASecondary journal sleeve Stainless Steel 304Impeller Stainless Steel 304Cable guard Stainless Steel 316Suction strainer Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 316Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
Submersible Pumps
6” Stainless Steel Submersible Pumps150 GPM Performance Curve
PAGE: SP-135DATE: July 1, 2008
M3PH
0
200
150
100
50
0 40 50302010
0
200
400
600
800
0 40 80 120 160 200
80
70
60
50
EF
FIC
IEN
CY
%
ME
TE
RS
FE
ET
GPM
20 hp
15 hp
15 hp
10 hp
7.5 hp
Submersible Pumps
6” Stainless Steel Submersible Pumps150 GPM Specifi cations
Mi8038
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
D
P
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
7.5 3 3” 4” 5.55” 14.4” 2310 4 3” 4” 5.55” 16.2” 2515 5 3” 6” 5.67” 18.0” 2815 7 3” 6” 5.67” 21.7” 3220 9 3” 6” 5.67” 25.3” 36
Dimension Information
*Note: D = Discharge, P = Pump Length
Parts DescriptionMaterial
Type AISIOuter case with motor adapter Stainless Steel 304Discharge head with built-in check valve Stainless Steel 304Sealing O-ring Nitrile Rubber (NBR) N/AUpper bowl Stainless Steel 304Upper bearing bushing Nitrile Rubber (NBR) N/A
Upper journal sleeve Stainless Steel w/ ceramic coating 329
Pump shaft Stainless Steel 431Motor coupling Stainless Steel 431/329Diffuser Stainless Steel 304Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/ASecondary journal sleeve Stainless Steel 304Impeller Stainless Steel 304Cable guard Stainless Steel 316Suction strainer Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 316Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
Submersible Pumps
6” Stainless Steel Submersible Pumps150 GPM Performance Curve
PAGE: SP-140DATE: July 1, 2008
M3PH
0
400
350
300
250
200
150
100
50
0 40 50302010
50 hp
40 hp
40 hp
30 hp
25 hp
0
200
400
600
800
1000
1200
1400
0 40 80 120 160 200
80
70
60
50
40
EF
FIC
IEN
CY
%
ME
TE
RS
FE
ET
GPM
Submersible Pumps
6” Stainless Steel Submersible Pumps150 GPM Specifi cations
Mi8039
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
D
P
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
25 11 3” 6” 5.67” 29.0” 4130 14 3” 6” 5.67” 34.5” 4740 15 3” 6” 5.67” 36.8” 4940 19 3” 6” 5.67” 43.7” 5750 23 3” 6” 5.67” 51.0” 66
Dimension Information
*Note: D = Discharge, P = Pump Length
Parts DescriptionMaterial
Type AISIOuter case with motor adapter Stainless Steel 304Discharge head with built-in check valve Stainless Steel 304Sealing O-ring Nitrile Rubber (NBR) N/AUpper bowl Stainless Steel 304Upper bearing bushing Nitrile Rubber (NBR) N/A
Upper journal sleeve Stainless Steel w/ ceramic coating 329
Pump shaft Stainless Steel 431Motor coupling Stainless Steel 431/329Diffuser Stainless Steel 304Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/ASecondary journal sleeve Stainless Steel 304Impeller Stainless Steel 304Cable guard Stainless Steel 316Suction strainer Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 316Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
Submersible Pumps
6” Stainless Steel Submersible Pumps240 GPM Performance Curve
PAGE: SP-145DATE: July 1, 2008
0
150
100
50
0 706040 50302010
0
200
400
600
0 40 80 120 160 200 240 280
20 hp
20 hp
15 hp
10 hp
7.5 hp
80
70
60
50
40
EF
FIC
IEN
CY
%
M3PH
ME
TE
RS
FE
ET
GPM
Submersible Pumps
6” Stainless Steel Submersible Pumps240 GPM Specifi cations
Mi8047
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
D
P
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
7.5 2 3” 4” 5.55” 14.4” 2410 3 3” 4” 5.55” 18.1” 3015 4 3” 6” 5.67” 21.7” 3520 5 3” 6” 5.67” 25.3” 4020 6 3” 6” 5.67” 29.0” 45
Dimension Information
*Note: D = Discharge, P = Pump Length
Parts DescriptionMaterial
Type AISIOuter case with motor adapter Stainless Steel 304Discharge head with built-in check valve Stainless Steel 304Sealing O-ring Nitrile Rubber (NBR) N/AUpper bowl Stainless Steel 304Upper bearing bushing Nitrile Rubber (NBR) N/A
Upper journal sleeve Stainless Steel w/ ceramic coating 329
Pump shaft Stainless Steel 431Motor coupling Stainless Steel 431/329Diffuser Stainless Steel 304Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/ASecondary journal sleeve Stainless Steel 304Impeller Stainless Steel 304Cable guard Stainless Steel 316Suction strainer Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 316Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
Submersible Pumps
6” Stainless Steel Submersible Pumps240 GPM Performance Curve
PAGE: SP-150DATE: July 1, 2008
0
350
300
250
200
150
100
50
0 706040 50302010
0
200
400
600
800
1000
0 40 80 120 160 200 240 280
50 hp
40 hp
40 hp
30 hp
25 hp
80
70
60
50
40
EF
FIC
IEN
CY
%
M3PH
ME
TE
RS
FE
ET
GPM
Submersible Pumps
6” Stainless Steel Submersible Pumps240 GPM Specifi cations
Mi8048
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
D
P
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
25 7 3” 6” 5.67” 32.6” 5030 9 3” 6” 5.67” 39.9” 6040 10 3” 6” 5.67” 43.6” 6540 12 3” 6” 5.67” 50.9” 7550 15 3” 6” 5.67” 61.9” 90
Dimension Information
*Note: D = Discharge, P = Pump Length
Parts DescriptionMaterial
Type AISIOuter case with motor adapter Stainless Steel 304Discharge head with built-in check valve Stainless Steel 304Sealing O-ring Nitrile Rubber (NBR) N/AUpper bowl Stainless Steel 304Upper bearing bushing Nitrile Rubber (NBR) N/A
Upper journal sleeve Stainless Steel w/ ceramic coating 329
Pump shaft Stainless Steel 431Motor coupling Stainless Steel 431/329Diffuser Stainless Steel 304Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/ASecondary journal sleeve Stainless Steel 304Impeller Stainless Steel 304Cable guard Stainless Steel 316Suction strainer Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 316Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
Submersible Pumps
6” Stainless Steel Submersible Pumps300 GPM Performance Curve
PAGE: SP-155DATE: July 1, 2008
0 40 80 120 160 200 240 280 320
0 10 20 30 40 80706050
0
200
400
600
100
300
500
0
150
100
50
25 hp
20 hp
20 hp
15 hp
10 hp
7.5 hp
80
70
60
50
40
EF
FIC
IEN
CY
%
FE
ET
ME
TE
RS
M3PH
GPM
Submersible Pumps
6” Stainless Steel Submersible Pumps300 GPM Specifi cations
Mi8042
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
D
P
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
7.5 2 3” 4” 5.55” 14.4” 2510 3 3” 4” 5.55” 18.0” 3015 4 3” 6” 5.67” 21.7” 3520 5 3” 6” 5.67” 25.3” 4020 6 3” 6” 5.67” 29.0” 4525 7 3” 6” 5.67” 32.6” 51
Dimension Information
*Note: D = Discharge, P = Pump Length
Parts DescriptionMaterial
Type AISIOuter case with motor adapter Stainless Steel 304Discharge head with built-in check valve Stainless Steel 304Sealing O-ring Nitrile Rubber (NBR) N/AUpper bowl Stainless Steel 304Upper bearing bushing Nitrile Rubber (NBR) N/A
Upper journal sleeve Stainless Steel w/ ceramic coating 329
Pump shaft Stainless Steel 431Motor coupling Stainless Steel 431/329Diffuser Stainless Steel 304Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/ASecondary journal sleeve Stainless Steel 304Impeller Stainless Steel 304Cable guard Stainless Steel 316Suction strainer Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 316Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
Submersible Pumps
6” Stainless Steel Submersible Pumps300 GPM Performance Curve
PAGE: SP-160DATE: July 1, 2008
0 40 80 120 160 200 240 280 320
0 10 20 30 40 80706050
0
200
400
600
800
1000
1100
100
300
500
700
900
0
300
250
200
150
100
50
50 hp
50 hp
40 hp
40 hp
30 hp
30 hp
80
70
60
50
40
EF
FIC
IEN
CY
%
M3PH
FE
ET
ME
TE
RS
GPM
Submersible Pumps
6” Stainless Steel Submersible Pumps300 GPM Specifi cations
Mi8043
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
D
P
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
30 8 4” 6” 5.67” 36.3” 5530 9 4” 6” 5.67” 39.9” 6040 10 4” 6” 5.67” 43.6” 6640 12 4” 6” 5.67” 50.9” 7550 14 4” 6” 5.67” 58.2” 8650 15 4” 6” 5.67” 61.9” 90
Dimension Information
*Note: D = Discharge, P = Pump Length
Parts DescriptionMaterial
Type AISIOuter case with motor adapter Stainless Steel 304Discharge head with built-in check valve Stainless Steel 304Sealing O-ring Nitrile Rubber (NBR) N/AUpper bowl Stainless Steel 304Upper bearing bushing Nitrile Rubber (NBR) N/A
Upper journal sleeve Stainless Steel w/ ceramic coating 329
Pump shaft Stainless Steel 431Motor coupling Stainless Steel 431/329Diffuser Stainless Steel 304Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/ASecondary journal sleeve Stainless Steel 304Impeller Stainless Steel 304Cable guard Stainless Steel 316Suction strainer Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 316Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
Submersible Pumps
8” Stainless Steel Submersible Pumps400 GPM Performance Curve
PAGE: SP-165DATE: July 1, 2008
0 100 200 300 400 5000
200
400
600
0
150
100
50
20 40 60 80 100 120
40 hp
30 hp
25 hp
15 hp
0
100
80
60
40
EF
FIC
IEN
CY
%
M3PH
FE
ET
GPM
ME
TE
RS
Submersible Pumps
8” Stainless Steel Submersible Pumps400 GPM Specifi cations
Mi8044
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
L
D
P
Parts DescriptionMaterial
Type AISIOuter case Stainless Steel 316Motor adapter and fl ange Stainless Steel 316Suction strainer Stainless Steel 316Discharge head Stainless Steel 316Check valve assembly Stainless Steel 316Sealing O-ring Nitrile Rubber (NBR) N/AStop ring Stainless Steel 316Spring Stainless Steel 316Pump shaft Stainless Steel 329Upper journal sleeve Silicon Carbide (SiC) N/AMotor coupling Stainless Steel 316/329Diffuser Stainless Steel 316Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/AFlange clamping neck ring Stainless Steel 316Impeller Stainless Steel 316Collet Stainless Steel 316Collet nut Stainless Steel 316Cable guard Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 329Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
15 2 4” 6” 7.34” 25.3” 7025 3 4” 6” 7.34” 30.3” 8130 4 4” 6” 7.34” 35.2” 9240 5 4” 6” 7.34” 40.2” 103
Dimension Information
*Note: D = Discharge, P = Pump Length
Submersible Pumps
8” Stainless Steel Submersible Pumps400 GPM Performance Curve
PAGE: SP-170DATE: July 1, 2008
0 100 200 300 400 5000
200
400
600
800
1000
1200
1400
0
400
350
300
250
200
150
100
50
20 40 60 80 100 120
100 hp
75 hp
60 hp
50 hp
0
100
80
60
40
EF
FIC
IEN
CY
%
M3PH
FE
ET
GPM
ME
TE
RS
Submersible Pumps
8” Stainless Steel Submersible Pumps400 GPM Specifi cations
Mi8045
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
L
D
P
Parts DescriptionMaterial
Type AISIOuter case Stainless Steel 316Motor adapter and fl ange Stainless Steel 316Suction strainer Stainless Steel 316Discharge head Stainless Steel 316Check valve assembly Stainless Steel 316Sealing O-ring Nitrile Rubber (NBR) N/AStop ring Stainless Steel 316Spring Stainless Steel 316Pump shaft Stainless Steel 329Upper journal sleeve Silicon Carbide (SiC) N/AMotor coupling Stainless Steel 316/329Diffuser Stainless Steel 316Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/AFlange clamping neck ring Stainless Steel 316Impeller Stainless Steel 316Collet Stainless Steel 316Collet nut Stainless Steel 316Cable guard Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 329Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
50 7 4” 6” 7.34” 50.1” 12460 8 4” 8” 7.34” 55.0” 13575 10 4” 8” 7.34” 65.1” 157
100 13 4” 8” 7.34” 80.0” 192
Dimension Information
*Note: D = Discharge, P = Pump Length
Submersible Pumps
8” Stainless Steel Submersible Pumps475 GPM Performance Curve
PAGE: SP-175DATE: July 1, 2008
0 100 200 300 400 500 7006000
200
400
600
800
1000
1200
1400
0
400
350
300
250
200
150
100
50
0 20 40 60 80 100 120 140 160
100
80
60
40
125 hp
100 hp
75 hp
60 hp
50 hp
40 hp
30 hp
EF
FIC
IEN
CY
%
M3PH
FE
ET
GPM
ME
TE
RS
Submersible Pumps
8” Stainless Steel Submersible Pumps475 GPM Specifi cations
Mi8046
400 East Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
L
D
P
Parts DescriptionMaterial
Type AISIOuter case Stainless Steel 316Motor adapter and fl ange Stainless Steel 316Suction strainer Stainless Steel 316Discharge head Stainless Steel 316Check valve assembly Stainless Steel 316Sealing O-ring Nitrile Rubber (NBR) N/AStop ring Stainless Steel 316Spring Stainless Steel 316Pump shaft Stainless Steel 329Upper journal sleeve Silicon Carbide (SiC) N/AMotor coupling Stainless Steel 316/329Diffuser Stainless Steel 316Floating neck ring Tefl on (PTFE) N/ASecondary bearing bushing Nitrile Rubber (NBR) N/AFlange clamping neck ring Stainless Steel 316Impeller Stainless Steel 316Collet Stainless Steel 316Collet nut Stainless Steel 316Cable guard Stainless Steel 316Insert locking outer case Stainless Steel 316Up-thrust washer Stainless Steel 329Up-thrust disc Tefl on (PTFE) N/AScrews and washers Stainless Steel 316
HP Stages D* Motor Size Diameter w/Cable Guard P*
Pump WeightLbs.
30 3 6” 6” 7.34” 30.3” 8140 4 6” 6” 7.34” 35.2” 9250 6 6” 6” 7.34” 45.1” 11260 7 6” 6” 7.34” 50.1” 12475 8 6” 8” 7.68” 55.2” 138
100 10 6” 8” 7.68” 65.1” 159125 13 6” 8” 7.68” 80.0” 192
Dimension Information
*Note: D = Discharge, P = Pump Length
Centrifugal Pumps
PAGE: CP-100DATE: June 5, 2006
HB4 SeriesHorizontal Booster Pumps
Applications:■ Boosting water pressure from either city mains or private
water systems.
■ Pressure washing buildings and fl oors.
■ Poultry houses.
■ Spray Cooling Equipment.
■ Lawn and Crop Irrigation.
■ Evaporating cooling system/misters.
■ Water Circulation.
■ General Purpose pumping.
■ Reverse Osmosis- Stainless Steel HB4
■ Filtration- Stainless Steel HB4
Cast Iron Models Features:■ Custom O-Ring seal for reliable high pressure sealing.
■ Thermoplastic impellers and diffusers for increased effi ciency.
■ Open drip-proof motors.
■ Standard 5/8” type 21 shaft seal.
■ Durable, precision machined stainless steel shell.
■ Field selectable motors- 115V or 230V.
■ Convenient, sturdy carrying handle.
■ Proven ceramic discharge bearing design for high resistance to abrasive materials and corrosion.
■ Cast iron motor bracket and stainless steel discharge with 1” NPT.
■ Two piece brass coupling for easy fi eld serviceability.
Stainless Steel Models Features:All of the Cast Iron features except:
■ Stainless Steel motor bracket and discharge with 1”NPT.
■ Two piece stainless steel coupling for easy fi eld serviceability.
■ Viton mechanical shaft seal for added chemical resistance.
CAST IRON MODELS
GPM HPSingle Phase
Model No. Order No. Wt.5 1 1FHB4P5C15-S 91270515 48
81/2 5FHB4P8C9-S 91270809 373/4 7FHB4P8C11-S 91270811 42
123/4 7FHB4P12C7-S 91271207 401 1FHB4P12C9-S 91271209 44
16 1 1FHB4P16C7-S 91271607 43
22 1-1/2 15FHB4P22C7-S 91272207 50
STAINLESS STEEL MODELS
GPM HPSingle Phase
Model No. Order No. Wt.5 1 1FHB4P5S15-S 91274822 48
81/2 5FHB4P8S9-S 91274830 373/4 7FHB4P8S11-S 91274848 42
123/4 7FHB4P12S7-S 91274855 401 1FHB4P12S9-S 91274863 44
16 1 1FHB4P16S7-S 91274871 43
22 1-1/2 15FHB4P22S7-S 91274889 50
NOTE: Single phase 1/2 - 2HP motors rated 115/230 volts.
Ordering Information
Centrifugal Pumps
HB4 Series PerformanceHorizontal Booster Pumps
Mi8300
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-105DATE: June 5, 2006
H4 SeriesHorizontal Booster Pumps
This multi-purpose pump is ideal for boosting water pressure around the home, industry or farm and is constructed with fi eld-proven premium hydraulics. Available in a variety of sizes for many applications1/3 - 3HP and 5, 10, 18, and 25GPM performance ranges.
Features:■ Heavy-duty cast iron discharge housing and suction bracket
for long life.
■ Thermoplastic impellers and diffusers are molded for increased effi ciency and include fl oating eye seal, ceramic shaft sleeve and rubber discharge bearing.
■ Stainless Steel shell and shaft for increased durability.
■ Shaft coupling for easy serviceability.
■ Tie rod construction for easy disassembly.
■ Cast iron support foot for extra stability.
■ Open drip-proof motors.
■ 1/3 and 1/2HP models have 6-foot grounded cord and carrying handle.
■ Maximum water temperature is 120oF.
■ Maximum operating pressure is 400 PSI.
■ Handles up 150 PSI incoming pressure and handles up to 10 ft. of suction lift.
Model A B3FH4P5-7 14-3/16 10.19
5FH4P5-10 16-9/16 10.44
7FH4P5-14 19-3/4 11.19
1FH4P5-18 22-13/16 11.44
3FH4P10-4 12-1/4 10.19
5FH4P10-6 14-1/16 10.44
7FH4P10-9 16-11/16 11.19
1FH4P10-12 19-3/8 11.44
15FH4P10-16 22-13/16 11.94
5FH4P18-5 13-15/16 10.44
7FH4P18-7 16-1/6 11.19
1FH4P18-9 18-3/16 11.44
15FH4P18-12 21-5/6 11.94
2FH4P18-15 24-1/2 11.66
7FH4P25-5 14-13/16 11.19
1FH4P25-6 16-1/16 11.44
15FH4P25-9 19-3/4 11.94
2FH4P25-11 22-3/16 11.66
3FH4P25-16 28-1/4 12.66
Dimensions (In inches)
NOTE: Dimensions will vary according to motor manufacturer.
5-11/16”
3-1/2”
2-1/2”
4-1/4”
1” FNPTDISCHARGE
7/8”
7/16” SLOTS (2)
1-1/4” FNPTSUCTION
A
3-3/16”
7/16” HOLES (2)
1-1/4”
B
7-1/2”
Centrifugal Pumps
H4 SeriesHorizontal Booster Pumps
Mi8301
H4 HORIZONTAL BOOSTER PUMPS with OPEN DRIP PROOF MOTORS
GPM HPSINGLE PHASE THREE PHASE - 208-230/460 VOLT
Model No. Order No. Wt. Model No. Order No. Wt.
51/3 3FH4P57-S 91241507 35 3FH4P57-T 91243507 351/2 5FH4P510-S 91241510 37 5FH4P510-T 91243510 373/4 7FH4P514-S 91241514 42 7FH4P514-T 91243514 411 1FH4P518-S 91241518 46 1FH4P518-T 91243518 44
10
1/3 3FH4P104-S 91242104 25 3FH4P104-T 91243104 311/2 5FH4P106-S 91242106 36 5FH4P106-T 91243106 363/4 7FH4P109-S 91242109 39 7FH4P109-T 91243109 381 1FH4P1012-S 91242112 45 1FH4P1012-T 91243112 43
1-1/2 15FH4P1016-S 91242116 51 15FH4P1016-T 91243116 51
18
1/2 5FH4P185-S 91242805 36 5FH4P185-T 91243805 363/4 7FH4P187-S 91242807 39 7FH4P187-T 91243807 381 1FH4P189-S 91242809 43 1FH4P189-T 91243809 42
1-1/2 15FH4P1812-S 91242812 51 15FH4P1812-T 91243812 492 2FH4P1815-S 91242815 55 2FH4P1815-T 91243815 55
25
3/4 7FH4P255-S 91243505 38 7FH4P255-T 91244505 371 1FH4P256-S 91243506 42 1FH4P256-T 91244506 40
1-1/2 15FH4P259-S 91243509 49 15FH4P259-T 91244509 472 2FH4P2511-S 91243511 54 2FH4P2511-T 91244511 543 3FH4P2516-S 91243516 65 3FH4P2516-T 91244516 64
H4 BOOSTER PUMP ENDS H4 BOOSTER PUMPS - 575 VOLT
GPM HPPUMP ENDS THREE PHASE - 575VOLT
Model No. Order No. Wt. Model No. Order No. Wt.
5
1/3 3FH4P57 91240507 22 3FH4P57-T5 91244507 351/2 5FH4P510 91240510 23 5FH4P510-T5 91244510 373/4 7FH4P514 91240514 25 7FH4P514-T5 91244514 411 1FH4P518 91240518 26 1FH4P518-T5 91244518 44
10
1/3 3FH4P104 91241004 17 3FH4P104-T5 91244104 311/2 5FH4P106 91241006 22 5FH4P106-T5 91244106 363/4 7FH4P109 91241009 21 7FH4P109-T5 91244109 381 1FH4P1012 91241012 24 1FH4P1012-T5 91244112 43
1-1/2 15FH4P1016 91241016 26 15FH4P1016-T5 91244116 51
18
1/2 5FH4P185 91241805 22 5FH4P185-T5 91244805 363/4 7FH4P187 91241807 22 7FH4P187-T5 91244807 381 1FH4P189 91241809 23 1FH4P189-T5 91244809 42
1-1/2 15FH4P1812 91241812 25 15FH4P1812-T5 91244812 492 2FH4P1815 91241815 27 2FH4P1815-T5 91244815 55
25
3/4 7FH4P255 91242505 22 7FH4P255-T5 91245505 371 1FH4P256 91242506 22 1FH4P256-T5 91245506 40
1-1/2 15FH4P259 91242509 24 15FH4P259-T5 91245509 472 2FH4P2511 91242511 25 2FH4P2511-T5 91245511 543 3FH4P2516 91242516 28 3FH4P2516-T5 91245516 64
Ordering Information
NOTE: Single Phase 1/3 - 2HP motors rated 115/230V. Single Phase 3HP motor rated 230V. Three Phase motors rated 208-230/460V.
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-110DATE: June 5, 2006
5 GPM PerformanceH4 Horizontal Booster Pumps
NPSHR
1HP
3/4HP
1/2HP
1/3HP
BEST EFFICIENCY RANGE
10
20
30
NP
SH
R -
FE
ET
10
20
30
40
EF
FIC
IEN
CY
%
0 2 4 6 8
CAPACITY - GALLONS PER MINUTE
600
550
500
450
400
350
300
250
200
150
100
50
50
100
150
200
250
TO
TAL
HE
AD
- F
EE
T
PS
I
HPDischarge Pressure at Pump with no Lift (Capacities in GPM) Max Pres.
(PSI)40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 2301/3 8.1 7.3 6.5 5.6 4.5 3.1 98
1/2 7.9 7.3 6.8 6.2 5.6 4.8 4.0 2.9 140
3/4 7.8 7.4 7.0 6.6 6.1 5.7 5.2 4.6 4.1 3.4 2.5 192
1 7.8 7.5 7.2 6.8 6.5 6.2 5.8 5.4 5.1 4.7 4.2 3.7 3.1 2.3 244
Centrifugal Pumps
10 GPM PerformanceH4 Horizontal Booster Pumps
Mi8302
HPDischarge Pressure at Pump with no Lift (Capacities in GPM) Max Pres.
(PSI)20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 2101/3 14.4 12.6 10.5 7.5 56
1/2 15.3 14.2 13.1 11.8 10.3 8.3 4.6 84
3/4 15.8 15.1 14.4 13.6 12.7 11.8 10.8 9.7 8.4 6.9 4.3 125
1 16.2 15.7 15.2 14.6 14.1 13.5 12.9 12.2 11.5 10.8 9.9 8.9 7.8 6.3 4.2 166
1-1/2 16.7 16.2 15.8 15.3 14.9 14.4 14.0 13.5 13.1 12.6 12.1 11.6 11.0 10.4 9.8 9.1 8.4 7.6 6.6 5.3 220
1-1/2HP
1HP
3/4HP
1/2HP
1/3HP
BEST EFFICIENCY RANGE
NPSHR
CAPACITY - GALLONS PER MINUTE
30
20
10N
PS
HR
- F
EE
T
50
40
30
20
EF
FIC
IEN
CY
%
0 2 4 6 8 10 12 14 16
50
100
150
200
250
50
100
150
200
250
300
350
400
450
500
550
TO
TAL
HE
AD
- F
EE
T
PS
I
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-115DATE: June 5, 2006
18 GPM PerformanceH4 Horizontal Booster Pumps
HPDischarge Pressure at Pump with no Lift (Capacities in GPM) Max Pres.
(PSI)20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 1701/2 24.3 21.7 18.1 13.7 60
3/4 25.2 24.0 22.4 20.3 17.6 14.4 10.0 88
1 25.7 24.7 23.8 22.2 20.5 18.4 16.2 13.8 10.2 4.0 111
1-1/2 26.0 25.4 24.8 24.0 23.3 22.3 21.1 19.8 18.2 16.4 14.4 12.0 8.2 148
2 26.5 26.0 25.4 24.7 24.0 23.4 22.5 21.6 20.5 19.4 18.1 16.7 15.3 13.6 11.6 8.4 179
0 4 8 12 16 20 24
30
20
10
0
NP
SH
R -
FE
ET
50
40
30
20
EF
FIC
IEN
CY
%
CAPACITY - GALLONS PER MINUTE
BEST EFFICIENCY RANGE
NPSHR
2HP
1-1/2HP
1HP
3/4HP
1/2HP
50
100
150
200
PS
I
TO
TAL
HE
AD
- F
EE
T
50
100
150
200
250
300
350
400
450
Centrifugal Pumps
25 GPM PerformanceH4 Horizontal Booster Pumps
Mi8303
HPDischarge Pressure at Pump with no Lift (Capacities in GPM) Max Pres.
(PSI)20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 1903/4 33.0 30.0 26.4 20.8 61
1 34.0 31.8 28.8 25.4 21.2 14.8 76
1-1/2 35.4 34.0 32.8 31.0 29.0 26.6 24.0 20.8 17.0 112
2 35.8 34.7 33.8 32.6 31.2 29.4 27.4 25.2 22.8 20.8 16.8 12.0 138
3 36.2 35.5 34.6 33.8 33.0 32.2 31.2 30.2 29.2 27.8 26.6 25.0 23.2 21.6 19.6 17.2 14.0 9.6 198
BEST EFFICIENCY RANGE
NPSHR
3HP
2HP
1-1/2HP
1HP
3/4HP
60
50
40
30
20
EF
FIC
IEN
CY
%
30
20
10
0
NP
SH
R -
FE
ET
0 8 16 24 32
CAPACITY - GALLONS PER MINUTE
50
100
150
200
250
50
100
150
200
250
300
350
400
450
500
550
600
TO
TAL
HE
AD
- F
EE
T
PS
I
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-120DATE: June 5, 2006
V6 SeriesHigh Pressure Vertical Booster Pumps
Dimensions (In inches)2” TAPPINGSUCTION
B
C
A
2” TAPPINGDISCHARGE
9-3/167-11/16
19/32
The V6 Booster Pump is ideal for industrial/commercial applications where water pressure boosting is required. Designed with Premium hydraulics for reliability and excellent performance. The V650 is available in 1-1/2HP through 7-1/2HP models. The V675 is available in 3HP through 7-1/2HP models.
Features:■ Heavy-duty cast iron discharge housing and motor bracket
for long life.
■ Stainless steel shell, shaft coupling and pump shaft for increased durability.
■ Top access to mechanical seal for easy replacement of seal without disturbing the plumbing or disassembling the pump.
■ Standard thrust motors which are available through normal distribution channels.
■ High fl ow impellers and stages are glass-fi lled Noryl for added durability and strength.
■ Unique design allowing rotation of either suction or discharge in 90 degree increments for optimum installation fl exibility.
■ Tie-rod construction for easy disassembly and service to impeller stack.
■ Maximum water temperature is 120oF.
■ Maximum operating pressure is 150 PSI.
■ 2” FNPT Suction x 2” FNPT Discharge
HP AB C
1 Phase 3 Phase 1 Phase 3 Phase1-1/2 16-1/2” 10-1/2” 9-15/16” 27” 26-7/16”
2 18-1/8” 10-1/2” 9-15/16” 28-11/16” 28-1/16”
3 19-3/4” 11-3/16” 10-5/8” 30-15/16” 30-3/16”
5 25-3/8” 15-9/16” 14-3/4” 41-1/16” 40-1/8”
7-1/2 30-3/8” 15-7/8” 15-7/8” 46-1/4” 46-1/4”
HP AB C
1 Phase 3 Phase 1 Phase 3 Phase3 14-7/8” 12-7/8” 12-1/8” 27-3/4” 27”
5 20-1/2” 15-3/4” 14-1/2” 36-1/4” 35”
7-1/2 23-7/8” 15-7/8” 22-3/8” 39-3/4” 46-1/4”
50 GPM
75 GPM
NOTE: Shaft turns counter clockwise if viewed from above motor
Centrifugal Pumps
Mi8304
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
V6 SeriesHigh Pressure Vertical Booster Pumps
V6 VERTICAL BOOSTER PUMPS with OPEN DRIP PROOF MOTORS
GPM HPSINGLE PHASE THREE PHASE - 208-230/460 VOLT
Model No. Order No. Wt. Model No. Order No. Wt.
50
1-1/2 15FVB6P50-2-S 91303915 100 15FVB6P50-2-T 91304913 103
2 2FVB6P50-3-S 91303923 105 2FVB6P50-3-T 91303964 108
3 3FVB6P50-4-S 91303931 109 3FVB6P50-4-T 91303972 112
5 5FVB6P50-7-S 91304301 208 5FVB6P50-7-T 91304327 188
7-1/2 Not Available in Single Phase 7FVB6P50-10-T 91304293 225
75
3 3FVB6P75-2-S 91304244 106 3FVB6P75-2-T 91304251 108
5 5FVB6P75-4-S 91304350 208 5FVB6P75-4-T 91304368 182
7-1/2 Not Available in Single Phase 7FVB6P75-6-T 91304269 222
1-1/2 - 7-1/2 HP V6 SERIES BOOSTER PUMP ENDS V6 BOOSTER PUMPS - 575 VOLT
GPM HPPUMP ENDS ONLY THREE PHASE - 575 VOLT
Model No. Order No. Wt. Model No. Order No. Wt.
50
1-1/2 15FVB6P50-2 91304053 65 15FVB6P50-2-T5 91309019 103
2 2FVB6P50-3 91304061 72 2FVB6P50-3-T5 91309020 108
3 3FVB6P50-4 91304079 74 3FVB6P50-4-T5 91309021 112
5 5FVB6P50-7 91304335 89 5FVB6P50-7-T5 91309034 188
7-1/2 75FVB6P50-10 91304343 95 7FVB6P50-10-T5 91309035 225
75
3 3FVB6P75-2 91304277 70 3FVB6P75-2-T5 91309036 108
5 5FVB6P75-4 91304376 75 5FVB6P75-4-T5 91309037 182
7-1/2 75FVB6P75-6 91304285 84 7FVB6P75-6-T5 91309038 222
Ordering Information
NOTE: Single Phase 1/3 - 2HP motors rated 115/230V. Single Phase 3-5HP motor rated 230V. Three Phase motors rated 208-230/460V.
Centrifugal Pumps
PAGE: CP-125DATE: June 5, 2006
50 GPM PerformanceV6 High Pressure Vertical Booster Pumps
PS
I
TO
TA
L H
EA
D -
FE
ET
NP
SH
RE
FF
ICIE
NC
Y %
0
25
50
75
100
125
150
175
200
225
250
0
25
50
75
100
125
150
175
200
225
250
275
300
325
350
375
400
425
450
475
500
525
550
575
0 10 20 30 40 50 60 70 800
10
20
30
40
50
607-1/2HP
5HP
3HP
2HP
1-1/2HP
CAPACITY - GALLONS PER MINUTE
HPDischarge Pressure at Pump with no Lift (Capacities in GPM) Max Pres.
(PSI)10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 2301-1/2 82 70 56 34 46
2 80 72 62 50 35 69
3 78 72 65 57 47 35 18 95
5 79 75 71 67 63 60 54 48 42 35 25 10 165
7-1/2 79 77 74 71 68 65 62 59 55 51 47 43 38 31 25 17 238
1. Total discharge pressure of 1-1/2 thru 7-1/2HP. V6 series units should not exceed 150 PSI. 2. Total discharge pressure of 75VBH650 units should not exceed 400 PSI.
Notes:
Centrifugal Pumps
75 GPM PerformanceV6 High Pressure Vertical Booster Pumps
Mi8305
PS
I
TO
TA
L H
EA
D -
FE
ET
CAPACITY - GALLONS PER MINUTE
NP
SH
RE
FF
ICIE
NC
Y %60
50
40
0
10
20
0 10 20 30 40 50 60 70 80 90 100 110
0
25
50
75
100
125
150
0
25
50
75
100
125
150
175
200
225
250
275
300
325
350 7-1/2HP
5HP
3HP
HPDischarge Pressure at Pump with no Lift (Capacities in GPM) Max Pres.
(PSI)20 30 35 40 50 60 70 80 90 100 110 120 130 1403 100 82 70 50 48
5 108 104 94 86 76 58 20 93
7-1/2 106 100 94 88 82 76 66 56 20 143
1. Total discharge pressure of V6 Series units should not exceed 150PSI.
Note:
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
The self-priming sprinkler pump is ideal as a lawn sprinkler pump, or for general recirculation.
Features:■ Self-priming with large 1” priming port
■ Non-corrosive thermoplastic case with engineered-fl ow, high-effi ciency, low-noise design
■ High performance, thermoplastic hydraulics, including fl oating eye seal and stainless steel impeller wear ring
■ 1-1/2” FNPT threaded suction and discharge
■ Built in drain plug to facilitate servicing/winterizing
■ Square-fl ange motor design
■ Easy motor toggle switch changes from 230V to 115V without rewiring (Not available on 2HP)
■ Available in 3/4, 1, 1-1/2, and 2HP
■ Handles water temperatures up to 120oF and working pressure up to 75 PSI
PAGE: CP-200DATE: June 5, 2006
TY SeriesSelf Priming Sprinkler Pumps - Thermoplastic
Dimensions (In inches)
Note: Dimensions will vary according to motor manufacturer.
Ordering InformationSELF-PRIMING LAWN SPRINKLER PUMPS
Model HP VoltagePUMP UNIT
Order No. Wt.
7FPTY 3/4 115/230 93372007 37
10FPTY 1 115/230 93372010 38
15FPTY 1-1/2 115/230 93372015 40
20FPTY 2 230 93372020 43
HP Frame A3/4 48 18-1/4”
1 48 18-1/2”
1-1/2 48 18-3/8”
2 56 19-7/8”10.162.50
3.20
3.00
9.75 11
.83
8.874.37
2.70A
Centrifugal Pumps
TY Series PerformanceSelf Priming Sprinkler Pumps - Thermoplastic
Mi8344
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
GPMCAPACITY
ME
TE
RS
PS
I
FE
ET
0
5
10
15
20
25
30
35
0
10
20
30
40
50
0
10
20
30
40
50
60
70
80
90
100
110
120
0 10 20 30 40 50 60 70 80 90
TO
TA
L D
YN
AM
IC H
EA
D
2HP
1½HP
1HP
¾HP
HPTotal
SuctionLift in feet
Discharge PSIShut off
Pressure (PSI)20 25 30 35 40
Capacity in GPM
3/4
5 43 39 35 28 16 4210 41 37 32 23 - 4015 39 35 29 18 - 3820 38 33 25 - - 35
1
5 50 45 40 33 21 4310 49 44 37 29 7 4115 46 41 35 24 - 3920 44 39 31 12 - 36
1-1/2
5 65 60 54 44 30 4410 64 57 50 38 21 4215 61 54 46 31 7 4020 58 50 41 23 - 37
2
5 79 76 72 65 52 4610 78 74 69 59 45 4415 76 72 67 54 38 4220 74 70 63 47 20 39
Centrifugal Pumps
Features:■ Heavy duty cast iron case with engineered high effi ciency,
quiet run design
■ High performance, thermoplastic hydraulics, including fl oating eye seal and stainless steel impeller wear ring
■ 1-1/2” FNPT threaded suction and discharge ports
■ Self-priming with large 1” priming port
■ Built in drain plug to facilitate servicing/winterizing
■ Handles water temperatures up to 120oF and working pressure up to 75 PSI
■ All models have 2 compartment motors
■ Easy motor toggle switch changes from 230V to 115V without rewiring (Not available on 2HP)
PAGE: CP-205DATE: June 5, 2006
TYCI SeriesSelf Priming Sprinkler Pumps - Cast Iron
Dimensions (In inches)
Note: Dimensions will vary according to motor manufacturer.
Ordering InformationSELF-PRIMING LAWN SPRINKLER PUMPS
Model HP VoltagePUMP UNIT
Order No. Wt.
7FPTYCI 3/4 115/230 93373007 51
10FPTYCI 1 115/230 93373010 66
15FPTYCI 1-1/2 115/230 93373015 82
20FPTYCI 2 230 93373020 99
HP Frame A3/4 48 18-1/4”
1 48 18-1/2”
1-1/2 48 18-3/8”
2 56 19-7/8”
A2.70
8.87
10.742.50
3.20
3.00
9.75
11.8
3
Centrifugal Pumps
TYCI Series PerformanceSelf Priming Sprinkler Pumps - Cast Iron
Mi8345
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
GPMCAPACITY
ME
TE
RS
PS
I
FE
ET
0
5
10
15
20
25
30
35
0
10
20
30
40
50
0
10
20
30
40
50
60
70
80
90
100
110
120
0 10 20 30 40 50 60 70 80 90
TO
TA
L D
YN
AM
IC H
EA
D
2HP
1½HP
1HP
¾HP
HPTotal
SuctionLift in feet
Discharge PSIShut off
Pressure (PSI)20 25 30 35 40
Capacity in GPM
3/4
5 43 39 35 28 16 4210 41 37 32 23 - 4015 39 35 29 18 - 3820 38 33 25 - - 35
1
5 50 45 40 33 21 4310 49 44 37 29 7 4115 46 41 35 24 - 3920 44 39 31 12 - 36
1-1/2
5 65 60 54 44 30 4410 64 57 50 38 21 4215 61 54 46 31 7 4020 58 50 41 23 - 37
2
5 79 76 72 65 52 4610 78 74 69 59 45 4415 76 72 67 54 38 4220 74 70 63 47 20 39
Centrifugal Pumps
The HJ Series Lawn Sprinkler Pumps are designed to handle a large capacity of water at high pressure. They are ideal for continuous use on lawn sprinkler systems, for garden irrigation, for boosting city main pressures and for recirculating water.
Features:■ Stub Shaft motor with bronze coupling and bronze impeller
offers easy serviceability and premium construction features
■ Cast iron pump case, large capacity case ensures excellent self-priming performance
■ Thermoplastic diffuser for improved pressures
■ Mechanical shaft seal ensures leakproof fi t and continuous water lubrication
■ Two-compartment motor for easy service. All motors are single phase 115/230V
PAGE: CP-210DATE: June 5, 2006
HJ SeriesSelf Priming Sprinkler Pumps
Dimensions (In inches)
Note: Dimensions will vary according to motor manufacturer.
Ordering InformationSELF-PRIMING LAWN SPRINKLER PUMPS
HPSuction x Discharge
VoltagePump Unit
Order No. Wt.
1 1-1/2” x 1-1/2” 115/230 93371876 56
1-1/2 2” X 1-1/2” 115/230 93371884 61
2 2” X 1-1/2” 230 93371892 65
HP A1 17-5/8”
1-1/2 18-5/8”
2 19-5/8”
11-1/2
7-7/8
A
8-3/8
Centrifugal Pumps
HJ Series PerformanceSelf Priming Sprinkler Pumps
Mi8347
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
MET
ERS
PSI
FEET
GPM
NPS
HR
0
5
10
15
20
25
30
35
0
10
20
30
40
50
0
10
20
30
40
50
60
70
80
90
100
110
120
100 20 30 40 50 60 700
5
10
1-1/2HP2HP
1HP
BEST EFFICIENCY RANGE
HPTotal Suction lift in
Ft.
Discharge PSI Shut OffPressure
(PSI)20 25 30 35 40
Capacities in GPM
1
5 44 43 40 33 22 4110 41 39 36 30 - 4115 38 37 34 25 - 3920 34 33 30 - - 36
1-1/2
5 45 44 44 43 41 5210 44 44 43 42 40 4815 40 40 39 38 36 4620 37 36 36 34 32 44
2
5 61 60 59 56 50 4910 59 58 56 53 45 4815 57 57 55 51 40 4520 50 48 47 44 35 42
High Flow Full Service Factor
Centrifugal Pumps
The solution to your higher performance, irrigation and utility transfer requirements. This pump offers higher performance and faster priming in a self-priming centrifugal design.
Features:■ Available in high head or medium head performance.
■ Easy-service, back pull-out design.
■ Rugged construction with bronze impeller, heavy-duty motor, and mechanical seal.
■ Suction fl ange check valves included with each unit.
PAGE: CP-215DATE: June 5, 2006
SPC SeriesSelf Priming Centrifugal Pumps
9-1/2
E 4-3/4
1/4 NPT
3-3/43-3/49
F
1/2
7-7/16
Suction
4-1/2
13-1/4
7/8
5-1/4
12-3/4
Discharge
BC
D D
9-3/4
A
3-15/16
Model A B C D E F3SPC 6 20-3/4 15 2-1/4 8-1/8 6-1/2
5SPC 7 21-3/4 15-1/2 2-3/4 9 7
Note: Overall length (B) is shown for single phase motors.
Dimensions (In inches)
Note: Dimensions will vary according to motor manufacturer.
HIGH HEAD
Model No. Ordering No. HP Suction Size Discharge Size Volts Phase Weight3SPCH-S2 9312-7595 3 2 1-1/2 208/230 1 144
3SPCH-T 9312-7603 3 2 1-1/2 208/230/460 3 144
5SPCH-S2 9312-7637 5 2-1/2 2 208/230 1 165
5SPCH-T 9312-7652 5 3 2-1/2 208/230/460 3 133
MEDIUM HEAD3SPCM-S2 9312-7611 3 2-1/2 2 208/230 1 144
3SPCM-T 9312-7629 3 2-1/2 2 208/230/460 3 144
5SPCM-S2 9312-7660 5 3 2-1/2 208/230 1 165
5SPCM-T 9312-7678 5 3 2-1/2 208/230/460 3 133
Ordering Information
Centrifugal Pumps
SPC Series PerformanceSelf Priming Centrifugal Pumps
Mi8306
3SPCH
5SPCH
3SPCM5SPCM
40 80 120 160 200 240
CAPACITY - GALLONS PER MINUTE
0
10
20
30
40
50
60
70
PS
I
0
20
40
60
80
100
120
140
160
TO
TAL
HE
AD
- F
EE
T
HIGH HEAD Capacities GPM
Model No. HPDischarge Pressure Feet Suction Lift in FeetPSI Head 5 10 15 20 25
3SPCH 3
20 46 123 120 109 90 7030 69 108 105 98 91 6840 92 87 82 76 70 6250 115 60 52 44 33 18
5SPCH 5
20 46 182 160 151 140 9030 69 160 159 150 136 9840 92 146 141 135 130 9650 115 118 115 104 94 9460 138 80 71 54 28 -
MEDIUM HEAD Capacities GPM
Model No. HPDischarge Pressure Feet Suction Lift in FeetPSI Head 5 10 15 20 25
3SPCM 320 46 156 150 140 135 10030 69 124 116 108 99 9140 92 84 76 40 30 -
5SPCM 5
20 46 218 212 206 199 17230 69 190 182 176 170 16040 92 160 148 140 136 12850 115 118 116 90 72 36
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-300DATE: June 5, 2006
DDD/DDS SeriesEnd Suction Centrifugal Pumps
Features:■ Available in Cast Iron(DDD Series) or Stainless Steel
(DDS Series) models.
DDD Series Features:■ Cast iron seal plate for dependable high temperature
operation.
■ Glass fi lled thermoplastic impeller for increased effi ciency and dependable high temperature operation.
■ Back pull-out design provides access to internal parts without disturbing the plumbing.
■ Mechanical shaft seal insures a leakproof fi t and continuous water lubrication.
■ Maximum temperature limit of 140oF and maximum working pressure of 150 PSI.
■ Square fl ange open drip-proof motor for easy service and reliability.
■ Available in single and three phase models.
■ Enclosed impeller design for increased effi ciencies.
■ Chemical resistant thermoplastic impeller.
DDS Series Features:All of the DDD Series features above except:
■ Viton Mechanical shaft seal for added chemical resitance.
■ 304SS Case and seal plate.2
1-5/16
13/32
9/16
15/32 4-7/16
6-1/2
1-13/16
1-7/8 2-3/4D
E
F
G
A
H
C
B
25-1/2
NRTL/C CSA108UL778
H.P. Suct.(NPT)
Disch.(NPT) A B C D E F G H
1/2 1-1/4” 1” 14-11/16” 2-3/8” 5-5/16” 4-7/16” 3-1/2” 4-5/8” 8-3/4” 5-1/2”3/4 1-1/4” 1” 14-11/16” 2-3/8” 5-5/16” 4-7/16” 3-1/2” 4-5/8” 8-3/4” 5-1/2”1 1-1/4” 1” 14-11/16” 2-3/8” 5-5/16” 4-7/16” 3-1/2” 4-5/8” 8-3/4” 5-1/2”
1-1/2 1-1/4” 1” 15-3/16” 2-3/8” 5-5/16” 4-7/16” 3-1/2” 4-5/8” 8-3/4” 5-1/2”2 1-1/2” 1-1/4” 16-11/16” 2-13/16” 6-1/8” 5” 3-9/16” 5” 9-1/8” 6-5/16”
2-1/2 2” 1-1/2” 16-11/16” 2-13/16” 6-1/8” 5” 3-9/16” 5” 9-1/8” 6-5/16”
Dimensions
Centrifugal Pumps
DDD/DDS SeriesEnd Suction Centrifugal Pumps
Mi8307
DDD SERIES CENTRIFUGAL PUMP UNITS
SeriesSuction xDischarge
HPSingle Phase Three Phase - 208-230/460 Volt
Model No. Order No. Wt. Model No. Order No. Wt.
DDD
1-1/4” x 1”
1/2 5FPDDD1-S 93176928 27 5FPDDD1-T 93177991 27
3/4 7FPDDD1-S 93176936 31 7FPDDD1-T 93178007 31
1 1FPDDD1-S 93176944 33 1FPDDD1-T 93178015 33
1-1/2 15FPDDD1-S 93176951 38 15FPDDD1-T 93178023 38
1-1/2” x 1-1/4” 2 2FPDDD1-1/4-S 93176969 48 2FPDDD1-1/4-T 93178031 48
2” x 1-1/2” 2-1/2 25FPDDD1-1/2S 93176977 46 25FPDDD1-1/2-T - -
DDD Series - Cast Iron Ordering Information
DDS SERIES CENTRIFUGAL PUMP UNITS
SeriesSuction xDischarge
HPSingle Phase Three Phase - 208-230/460 Volt
Model No. Order No. Wt. Model No. Order No. Wt.
DDS 1-1/4” x 1”
1/2 5FPDDS1-S 93178056 25 5FPDDS1-T 93178098 25
3/4 7FPDDS1-S 93178064 29 7FPDDS1-T 93178106 29
1 1FPDDS1-S 93178072 31 1FPDDS1-T 93178114 31
1-1/2 15FPDDS1-S 93178080 36 15FPDDS1-T 93178122 36
DDS Series - Stainless Steel Ordering Information
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
DDD/DDS SERIES CENTRIFUGAL PUMP END KITS for 3500 R.P.M. - O.D.P. MOTORS
SeriesSuction x Discharge
HP Range
PhaseMotor Frame
SizeMax. Imp.Diameter
PUMP END KITModel No. Order No. Wt.
DDD DDS
1-1/4" x 1" 1/2 - 1-1/2 1 or 3 56Z 5.315”DDD1-K1 93177413R348
12DDS1-K1 93177413R378
1-1/2" x 1-1/4" 2 1 or 3 56Z 5.65” DDD1-1/4-K1 93177413R358 152" x 1-1/2" 2-1/2 1 or 3 56Z 5.95” DDD1-1/2-K1 93177413R368 14
DDD/DDS Series - Pump End Kits Ordering Information
Centrifugal Pumps
PAGE: CP-305DATE: June 5, 2006
DDD/DDS Series PerformanceEnd Suction Centrifugal Pumps
Mi8308
GPM
60
50
40
30
20
10
0
140
120
100
80
60
40
20
0
PS
I
FEE
T
NP
SH
R –
FE
ET15
10
5
0
0 10 20 30 40 50 60 70 80 90 100
2.5 BHP2BHP1.5 BHP1BHP.75 BHP.5 BHP
1/2-1-1/2HP
2-2-1/2HP
BEST EFFICIENCY RANGE
5.95” DIA
5.65” DIA
5.31” DIA
5.25” DIA
5.00” DIA
4.61” DIA
HPSuction
x Discharge
Capacities GPM Shut OffHead 30 35 40 45 50 60 70 80 90 100 110
Total Head - Feet1/2 1-1/4” x 1” 30 27 25 22 19 14 - - - - - 743/4 1-1/4” x 1” - 41 38 36 34 29 23 16 - - - 931 1-1/4” x 1” - - - 42 40 36 31 25 18 - - 105
1-1/2 1-1/4” x 1” - - - - 52 47 44 39 34 25 - 1182 1-1/2” x 1-1/4” - - - - - - 64 56 47 36 23 121
2-1/2 2” x 1-1/2” - - - - - - 68 61 53 45 35 131
NOTE: All performance data based on rated nameplate voltage.
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
DC1-1/2 DC4
DB2
DB3
DB1-1/2DB1
DDD
300
250
200
150
100
50
50 100 150 200 250 300 350 400 450 500 550 600 650
FE
ET
OF
HE
AD
CAPACITY - U.S. GALLONS PER MINUTE
DA1BDA1A
Features:■ Heavy-duty cast iron body for increased durability.
■ DA1A through DB2 have a bronze impeller.
■ DB3 and DC4 have cast iron impeller.
■ 1/3 - 2HP models have 56C frame motors with shaft coupling design for easy removal of pump motor.
■ 5 - 50HP models have JM frame motors with shaft sleeve/O-Ring design for added protection against shaft damage.
■ 3HP models can use either JM frame or 56 frame motors.
■ Single or three phase motors available on selected models.
■ Sealed motor bearings on all motors to carry radial and thrust loads of pump end.
■ All units are equipped with open drip-proof motors.
■ Max operating pressures 150 PSI.
■ Maximum operating temperature of 212oF on all models.
PAGE: CP-400DATE: June 5, 2006
Performance Curve
Note: Consult individual curves for complete pump performance.
DD
D SeriesEnd Suction Centrifugal Pumps
NRTL/CCSA108UL778
Centrifugal Pumps
D SeriesEnd Suction Centrifugal Pumps
DISCHARGE(NPT)
E
C
B B G
C
D
F
SUCTION(NPT)
SUCTION (NPT)
C
2 SLOTS FOR3/8 DIA. BOLTS6 5
1116
1 38
B G
C
D
F
C
DISCHARGE (NPT)
5 16
SUCTION (NPT)
2 HOLES FOR3/8 DIA. BOLTS
1 532
2 316
41 45
Pump Model Mtr.HP
Suct.NPT
Disch.NPT
Dimensions In Inches
Single Phase Three Phase A B C D E F G3DA1A-S 3DA1A-T 1/3
1-1/4 1
13-7/16
3-3/4 3-1/2 1-3/4 3-3/8 4-1/8 3-7/165DA1A-S 5DA1A-T 1/2 14-7/16
7DA1A-S 7DA1A-T 3/4 14-7/16
1DA1A-S 1DA1A-T 1 14-13/16
5DA1B-S 5DA1B-T 1/2
1-1/4 1
14-7/16
3-3/4 3-1/2 1-3/4 3-3/8 4-1/8 3-7/16
7DA1B-S 7DA1B-T 3/4 14-7/16
1DA1B-S 1DA1B-T 1 14-13/16
15DA1B-S 15DA1B-T 1-1/2 14-13/16
2DA1B-S 2DA1B-T 2 15-9/16
7DB1-S 7DB1-T 3/4
1-1/2 1
14-7/16
5 4 2-1/4 3-5/8 4-1/2 4-3/16
1DB1-S 1DB1-T 1 14-13/16
15DB1-S 15DB1-T 1-1/2 14-13/16
2DB1-S 2DB1-T 2 15-9/16
3DB1-S 3DB1-T 3 16-1/16
1DB1-1/2-S 1DB1-1/2-T 1
2 1-1/2
14-7/8
5 4-1/2 2-7/16 3-7/8 4-1/2 4-1/215DB1-1/2-S 15DB1-1/2-T 1-1/2 14-7/8
2DB1-1/2-S 2DB1-1/2-T 2 15-5/8
3DB1-1/2-S 3DB1-1/2-T 3 16-1/8
15DB2-S 15DB2-T 1-1/2
3 2
16-5/16
5 4-3/4 3-5/8 4-3/16 6 52DB2-S 2DB2-T 2 17-1/16
3DB2-S 3DB2-T 3 17-9/16
Notes: 1) Dimensions shown are based on 56C O.D.P. 3500 RPM motor. 2) In some cases dimensions “G” may be greater than “B”.
Mi8309
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-405DATE: June 5, 2006
D SeriesEnd Suction Centrifugal Pumps
C
DISCHARGE
B
A
D
E
SUCTION
DB1-DC4
JM Frame Motors - Extended shaft with keyway
Notes: 1) Total pump length will vary with motor manufacturer.
Pump Model
Suction(NPT)
Disch. (NPT)
A (HP) B (HP) C D E (HP)
3 5 7-1/2 10 15 20 3 5 7-1/2 10 15 20 3 5 7-1/2 10 15 20DB1 1-1/2 1 – 8-1/2 – – – – – 4-1/2 – – – – 3-5/8 2-1/16 – 18-1/8 – – – –
DB1-1/2 2 1-1/2 – 9 9-3/4 – – – – 4-1/2 5-1/4 – – – 3-7/8 2-7/16 – 18-3/16 19-1/2 – – –
DC1-1/2 2 1-1/2 10-1/8 10-1/8 10-7/8 10-7/8 10-7/8 – 4-1/2 4-1/2 5-1/4 5-1/4 5-1/4 – 5-3/16 2-1/2 17-1/8 18-1/8 19-7/16 19-7/16 21 –
DB2 3 2 – 9-1/4 10 10 11-3/8 12-3/8 – 4-1/2 5-1/4 5-1/4 5-1/4 6-1/4 4-3/16 3-5/8 – 19-5/8 21 21 22-1/2 22-1/2
DB3 4 3 – 11-9/16 11-9/16 12-5/16 12-5/16 13-5/16 – 4-1/2 4-1/2 5-1/4 5-1/4 5-1/4 4-1/16 3-1/2 – 19-3/16 20-3/16 21-3/4 24 28
Notes: 1) Dimensions shown are for units using 60 cycle open-dripproof JM frame motors, 3500 RPM.2) Total pump length will vary with motor manufacturer.
Pump ModelSuction (NPT)
Disch. (NPT)
A B C DJM Frame Motor Horsepower
20 25 30 40 50
DC4-FNPT 4 4 16-1/2 7-5/8 6-29/64 4-23/32 28-21/32 28-21/32 29-17/32 30 30
DC4-fl anged 5 4 16-1/2 7-5/8 6-29/64 3-13/16 28-21/32 28-21/32 29-17/32 30 30
Mi8350
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-410DATE: June 5, 2006
DD
Model DA1A Performance1” Discharge x 1-1/4” Suction (3500 RPM)
CAPACITY - GALLONS PER MINUTE
0 5 10 15 20 25 30 35 40
0
1020
20
40
60
30
80
40
50
120
100 5 -1/16 DIA.
4 -11/16 DIA.
4 -1/8 DIA.
3 -13/16 DIA.
PS
I
TO
TAL
HE
AD
- F
EE
T
45%50%
55%56%
55%
50%
57%
58%
NPSHR
1 BHP
.75 BHP
.5 BHP
.33 BHP
10
20
30
40
NP
SH
R -
FE
ET
DA1A 1-1/4” Suction x 1” Discharge
Capacities GPMShut-off
Head (Ft.)Total Head in Feet
Model HP Imp. Dia. 30 35 40 45 50 60 70 80 903DA1A 1/3 3-13/16 38 35 30 24 18 55
5DA1A 1/2 4-1/8 40 36 32 17 65
7DA1A 3/4 4-11/16 44 38 32 18 84
1DA1A 1 5-1/16 43 37 26 100
Note: All performance data based on rated nameplate voltage.
Centrifugal Pumps
Mi8310
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Model DA1B Performance1” Discharge x 1-1/4” Suction (3500 RPM)
DA1B 1-1/4” Suction x 1” Discharge
Capacities GPMShut-off
Head (Ft.)Total Head in Feet
Model HP Imp. Dia. 30 35 40 45 50 60 70 80 90 100 1105DA1B 1/2 3-3/4” 50 46 40 34 23 53
7DA1B 3/4 4” 62 57 51 35 68
1DA1B 1 4-1/4” 62 51 35 78
15DA1B 1-1/2 4-11/16” 70 63 53 33 95
2DA1B 2 5-1/16” 69 64 56 38 116
Note: All performance data based on rated nameplate voltage.
CAPACITY - GALLONS PER MINUTE
0 10 20 30 40 50 60 70 80
0
1020
20
40
60
30
80
40
50120
100
PS
I
TO
TAL
HE
AD
- F
EE
T
NPSHR10
20
30
40
NP
SH
R -
FE
ET
5-1/16 DIA.
4-11/16 DIA.
4-1/4 DIA.
4 DIA.
3-3/4 DIA.
40% 45% 50% 55%60%
62%
60%
55%65%
66%
2 BHP
1.5 BHP
1 BHP
.75 BHP.5 BHP
Centrifugal Pumps
PAGE: CP-415DATE: June 5, 2006
DD
Model DB1 Performance1” Discharge x 1-1/2” Suction (3500 RPM)
DB1 1-1/2” Suction x 1” Discharge
Capacities GPMShut-off
Head (Ft.)Total Head in Feet
Model HP Imp. Dia. 25 30 35 40 45 50 60 70 80 90 100 110 120 130 140 150 1607DB1 3/4 4-1/4” 61 58 54 49 46 41 29 72
1DB1 1 4-3/4” 67 63 59 56 46 36 20 84
15DB1 1-1/2 5-3/16” 72 65 58 50 39 28 109
2DB1 2 5-1/2” 74 68 61 53 45 33 122
3DB1 3 6-1/8” 78 73 67 61 54 46 37 151
5DB1 5 6-7/16” 80 74 68 62 53 42 174
Note: All performance data based on rated nameplate voltage.
6-7/16 DIA.
6-1/8 DIA.
5-1/2 DIA.
5-3/16 DIA.4-3/4 DIA.
4-1/4 DIA.
50% 52%
58%
56%
54%52%
50% 5 BHP
3 BHP
2 BHP1.5 BHP
1 BHP
.75 BHP
NPSHR
0 10 20 30 40 50 60 70 80 GPM
NPS
HR
- FE
ET
10
20
30
CAPACITIES - GALLONS PER MINUTE
0
10
20
30
40
50
60
70
80
90
100
110
120
50
0
100
150
200
250
PSI
TOTA
L H
EAD
- FE
ET
Centrifugal Pumps
Mi8311
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Model DB1-1/2 Performance1-1/2” Discharge x 2” Suction (3500 RPM)
DB1-1/2 2” Suction x 1-1/2” Discharge
Capacities GPMShut-off
Head (Ft.)
Total Head in Feet
Model HP Imp. Dia. 25 30 35 40 45 50 60 70 80 90 100 110 120 130 140 150 1601DB1-1/2 1 3-15/16” 125 105 95 86 75 63 60
15DB1-1/2 1-1/2 4-5/16” 123 118 112 106 96 78 50 75
2DB1-1/2 2 4-5/8” 130 126 120 115 100 82 52 87
3DB1-1/2 3 5-1/8” 144 132 118 103 88 62 110
5DB1-1/2 5 5-3/4” 163 153 141 126 107 78 140
75DB1-1/2 7-1/2 6-7/16” 170 165 135 130 170
Note: All performance data based on rated nameplate voltage.
6-7/16” DIA.
5-3/4” DIA.
5-1/8” DIA.
4-5/8” DIA.
4-5/16” DIA.
3-15/16” DIA.
55% 60%
64%
67%
68%
64%60%
7.5 BHP5 BHP
3 BHP2 BHP1.5 BHP
1 BHP
NPSHR NP
SH
R -
FE
ET
40
30
20
10
180160140120100806040200
PS
I
TO
TAL
HE
AD
- F
EE
T
200
150
100
50
0
90
70
50
30
10
CAPACITY - GALLONS PER MINUTE
Centrifugal Pumps
PAGE: CP-420DATE: June 5, 2006
DD
150
125
100
75
50
25
350
300
250
200
150
100
50
0 20 40 60 80 100 120 140 160 180
40
30
20
10
NP
SH
R –
FE
ET
CAPACITY - GALLONS PER MINUTE
TO
TAL
HE
AD
- F
EE
T
8-3/8" DIA.
7-5/16" DIA.
6-5/8" DIA.
5-13/16" DIA.
5-1/16" DIA.
NPSHR
50%
60%
60%
64%
20 BHP
15 BHP
10 BHP
7.5 BHP
5 BHP
3 BHP50%
PS
I
Model DC1-1/2 Performance1-1/2” Discharge x 2” Suction (3500 RPM)
DC1-1/2 2” Suction x 1-1/2” Discharge
Capacities GPM Shut-offHead (Ft.)
Total Head in Feet
Model HP Imp. Dia. 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 220 240 260 2803DC1-1/2 3 5-1/16” 130 120 108 92 70 100
5DC1-1/2 5 5-13/16” 155 144 132 118 100 84 56 135
75DC1-1/2 7-1/2 6-5/8” 180 170 160 150 130 110 80 180
10DC1-1/2 10 7-5/16” 176 167 156 143 126 106 220
15DC1-1/2 15 8-3/8” 184 167 140 100 300
Note: All performance data based on rated nameplate voltage.
Centrifugal Pumps
Mi8312
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
7-15/16” DIA.
7-1/4” DIA.
6-7/16” DIA.
5-13/16” DIA.
5-1/8” DIA.
4-1/2” DIA.
4” DIA.
3-13/16” DIA.
60%
65%
65%
70%
70%
72%
60%
20 BHP
15 BHP
10 BHP7.5 BHP
5 BHP
3 BHP
2 BHP
NPSHR
0 50 100 150 200 250 300 350 400
CAPACITY - GALLONS PER MINUTE
30
20
10 NPS
HR
- FE
ET0 0
2050
40100
60
80
150
200
100
120
250
PSI
TOTA
L H
EAD
- FE
ETModel DB2 Performance2” Discharge x 3” Suction (3500 RPM)
DB2 3” Suction x 2” Discharge
Capacities GPMShut-off
Head (Ft.)
Total Head in Feet
Model HP Imp. Dia. 20 25 30 35 40 45 50 60 70 80 90 100 110 120 150 200 25015DB2 1-1/2 3-13/16” 175 160 145 125 100 65 50
2DB2 2 4” 185 170 160 145 125 100 58
3DB2 3 4-1/2” 175 165 140 90 75
5DB2 5 5-1/8” 235 210 190 160 100
75DB2 7-1/2 5-13/16” 260 240 225 200 160 135
10DB2 10 6-7/16” 310 290 275 260 185 170
15DB2 15 7-1/4” 350 305 205 230
20DB2 20 7-15/16” 365 275 130 260
Note: All performance data based on rated nameplate voltage.
Centrifugal Pumps
PAGE: CP-421DATE: June 5, 2006
Model DB3 Performance3” Discharge x 4” Suction (3500 RPM)
DB3 4” Suction x 3” Discharge
Capacities GPMShut-off
Head (Ft.)
Total Head in Feet
Model HP Imp. Dia. 25 30 35 40 45 50 60 70 80 90 100 110 120 130 140 1505DB3 5 4-1/2” 335 305 280 250 220 200 60
75DB3 7-1/2 4-15/16” 440 425 405 385 365 320 260 81
10DB3 10 5-5/16” 505 490 470 440 400 360 250 101
15DB3 15 5-3/4” 600 580 550 510 460 430 380 300 128
20DB3 20 6” 630 610 590 550 530 510 450 380 146
Note: All performance data based on rated nameplate voltage.
CAPACITIES - GALLONS PER MINUTE
0 100 200 300 400 500 600 700 800
10
20
30
40
NP
SH
R -
FE
ET
00
10 25
50
30
75
100
50
125
70
150
TO
TAL
HE
AD
- F
EE
T
PS
I
6” DIA.
5-3/4” DIA.
5-3/16” DIA.
4-15/16” DIA.
4-1/2” DIA.
50% 55% 60% 64%68%
70%
72%
74%
70%
68%
64%
60%
55%
50%
20 BHP
15 BHP
10 BHP7.5 BHP
5 BHPNPSHR
Mi8313
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
Features:■ Epoxy-coated cast iron impeller for maximum effi ciency.
■ Mechanical shaft seal for water temperatures up to 212oF.
■ 4" NPT suction/discharge on 20-30 HP units.
■ Flanged 5" suction / 4" discharge on 40-50 HP units.
■ 20-50 HP pump end kits are available with either NPT suction/discharge or fl anged suction/discharge connections.
■ Maximum operating pressure of 150 PSI.
■ External balance line.
PAGE: CP-425DATE: June 5, 2006
DD
DC4 SeriesEnd Suction Centrifugal Pumps
Centrifugal Pumps
Model DC4 Performance(3500 RPM)
50 HP
40 HP
30 HP
25 HP
20 HP
50DC4
40DC4
30DC4
25DC4
20DC4
50DC4
40DC4
30DC4
25DC4
20DC4
50
40
30
20
10
20
10
0
NP
SH
RB
RA
KE
HP
0 50 100 150 200 250 300 350 400 450 500 550 600 650
CAPACITY - GALLONS PER MINUTE
75
100
125
150
175
200
225
250
275
300
325
30
40
50
60
70
80
90
100
110
120
130
140
PS
I
TO
TAL
HE
AD
- F
EE
T
IMP. DIA. 9-1/32
IMP. DIA. 8-7/16
IMP. DIA. 7-7/8
IMP. DIA. 7-15/32
IMP. DIA. 7-1/32
60
65
70
75
EF
FIC
IEN
CY
DC4Capacities GPM
Shut-offHead (Ft.)
Total Head in Feet
Model HP Imp. Dia. 90 100 120 140 150 160 170 180 190 200 210 220 240 260 280 29020DC4 20 7-1/32” 650 620 545 430 350 200 165
25DC4 25 7-15/32” 650 595 550 500 450 350 190
30DC4 30 7-7/8” 650 620 590 545 500 430 320 215
40DC4 40 8-7/16” 640 605 560 515 375 260
50DC4 50 9-1/32” 660 600 515 400 280 300
Note: All performance data based on rated nameplate voltage.
Mi8314
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
D SERIES CENTRIFUGAL PUMP UNITS with OPEN DRIP PROOF MOTORS
SeriesSuction x Discharge
HPSINGLE PHASE THREE PHASE - 208-230/460 VOLT
Model No. Order No. Wt. Model No. Order No. Wt.
DA1A 1-1/4" x 1"
1/3 3FPDA1A-S 93160012 32 3FPDA1A-T 93160053 31
1/2 5FPDA1A-S 93160020 35 5FPDA1A-T 93160061 343/4 7FPDA1A-S 93160038 36 7FPDA1A-T 93160079 371 1FPDA1A-S 93160046 37 1FPDA1A-T 93160087 38
DA1B 1-1/4" x 1"
1/2 5FPDA1B-S 93160137 36 5FPDA1B-T 93160186 31
3/4 7FPDA1B-S 93160145 38 7FPDA1B-T 93160194 33
1 1FPDA1B-S 93160152 40 1FPDA1B-T 93160202 35
1-1/2 15FPDA1B-S 93160160 46 15FPDA1B-T 93160210 45
2 2FPDA1B-S 93160178 49 2FPDA1B-T 93160228 48
DB1 1-1/2" x 1"
3/4 7FPDB1-S 93160285 42 7FPDB1-T 93160343 48
1 1FPDB1-S 93160293 45 1FPDB1-T 93160350 50
1-1/2 15FPDB1-S 93160301 55 15FPDB1-T 93160368 52
2 2FPDB1-S 93160319 53 2FPDB1-T 93160376 54
3 3FPDB1-S 93160327 74 3FPDB1-T 93160384 64
5 5FPDB1-S 93160335 122 5FPDB1-T 93160392 82
DB1-1/2 2" x 1-1/2"
1 1FPDB1-1/2-S 93160467 50 1FPDB1-1/2-T 93160525 47
1-1/2 15FPDB1-1/2-S 93160475 54 15FPDB1-1/2-T 93160533 52
2 2FPDB1-1/2-S 93160483 58 2FPDB1-1/2-T 93160541 55
3 3FPDB1-1/2-S 93160491 74 3FPDB1-1/2-T 93160558 63
5 5FPDB1-1/2-S 93160509 122 5FPDB1-1/2-T 93160566 102
7-1/2 75FPDB1-1/2-S 93160517 184 75FPDB1-1/2-T 93160574 110
DC1-1/2 2" x 1-1/2"
3 3FPDC1-1/2-S 93160830 122 3FPDC1-1/2-T 93120863 117
5 5FPDC1-1/2-S 93160848 142 5FPDC1-1/2-T 93160871 98
7-1/2 75FPDC1-1/2-S 93160855 162 75FPDC1-1/2-T 93160889 132
10 10FPDC1-1/2-S 93161168 190 10FPDC1-1/2-T 93160897 171
15 Not Available in Single Phase 15FPDC1-1/2-T 93160905 175
DB2 3" x 2"
1-1/2 15FPDB2-S 93160657 57 15FPDB2-T 93160707 57
2 2FPDB2-S 93160665 60 2FPDB2-T 93160715 60
3 3FPDB2-S 93160673 80 3FPDB2-T 93160723 72
5 5FPDB2-S 93160681 119 5FPDB2-T 93160731 110
7-1/2 75FPDB2-S 93160699 150 75FPDB2-T 93160749 116
10 10FPDB2-S 93161150 171 10FPDB2-T 93160756 146
15 Not Available in Single Phase 15FPDB2-T 93161051 210
20 Not Available in Single Phase 20FPDB2-T 93161069 243
DB3 4" x 3"
5 5FPDB3-S 93167330 132 5FPDB3-T 93167363 95
7-1/2 75FPDB3-S 93167348 160 75FPDB3-T 93167371 120
10 10FPDB3-S 93167355 174 10FPDB3-T 93167389 180
15 Not Available in Single Phase 15FPDB3-T 93167397 183
20 Not Available in Single Phase 20FPDB3-T 93167405 232
DC44" x 4"
20
Not Available in Single Phase
20FPDC4-T 93167710 312
25 25FPDC4-T 93167728 325
30 30FPDC4-T 93167736 389
5" x 4" Flanged40
Not Available in Single Phase40FPDC4-T 93167744 433
50 50FPDC4-T 93167785 593
Notes: Maximum O.D. impeller supplied with P.E. Kits. Impeller must be trimmed to match motor H.P.
*40-50 HP DC4 equipped with 125 lb. fl anged connections.Single phase 1/3 - 2 HP motors rated 115/230V.Single phase 3 - 10 HP motors rated 230V.Three phase motors rated 208-230/460 Volts.
PAGE: CP-430DATE: June 5, 2006
D SeriesOrdering Information
Mi8315
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
Maximize your fl exibility and response time for standard or special applications using end suction centrifugal pumps... industrial use, transfer circulation or booster service.
Features:■ Each kit has a maximum O.D. impeller that can be trimmed
to satisfy any of several horsepower requirements, thus eliminating the need to stock a complete unit for each horsepower. Note: Impellers should be balanced after trimming.
■ A case, bracket, and hardware kit come with each kit to build a complete pump (motor not included).
■ DC4 20 - 50HP pump end kits are available with either NPT suction/discharge or fl anged suction/discharge. All other models are NPT only.
■ Heavy-duty cast iron body for increased durability.
■ DA1A, DA1B, DB1-1/2, DC1-1/2, and DB2 Series are fi tted with bronze impeller.
■ DB3 is fi tted with cast iron impeller.
■ DC4 is fi tted with epoxy coated cast iron impeller.
■ DDD models include thermoplastic impellers.
■ 1/3 - 2HP models have 56C frame motors with shaft coupling design for easy removal. (Except DDD models which have 56Z frame motors.)
■ 5 - 50HP models have JM frame motors with shaft sleeve/ o-ring design for added protection against shaft damage.
■ 3HP models can use either JM or 56 frame motors.
■ Mechanical shaft seal handles water temperatures up to 212oF. Note: For higher temperature applications, consult your mechanical seal supplier.
■ Max. operating working pressure is 150 PSI.
■ All models are 3500 RPM. Models DB1, DB1-1/2, and DB2 are also available in 1750 RPM.
PAGE: CP-435DATE: June 5, 2006
DD
D SeriesPump End Kits
Mi8316
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909www.franklinpumps.com
Centrifugal Pumps
D SERIES CENTRIFUGAL PUMP END KITS for 3500 R.P.M. - O.D.P. MOTORS
SeriesSuction x Discharge
HP Range
PhaseMotor Frame
SizeMax. Imp.Diameter
PUMP END KITModel No. Order No. Wt.
DA1A 1-1/4” x 1” 1/3 - 1 1 or 3 56C 5-1/16” FPDA1A-K1 93167413R011 15
DA1B 1-1/4” x 1” 1/2 - 2 1 or 3 56C 5-1/16” FPDA1B-K1 93167413R021 15
DB1 1-1/2" x 1"3/4 - 3 1 or 3 56C 6-1/8” FPDB1-K1 93167413R032 25
5 3 182JM6-7/16” FPDB1-K2 93167413R053 35
5 1 184JM
DB1-1/2 2" x 1-1/2"
1 - 3 1 or 3 56C 5-1/8” FPDB1-1/2-K1 93167413R072 305 3 182JM
6-7/16” FPDB1-1/2-K2 93167413R083 405 1 184JM7-1/2 3 184JM7-1/2 1 213JM 6-7/16” FPDB1-1/2-K3 93167413R093 45
DC1-1/2 2" x 1-1/2"
3 3 145JM
5-3/16” FPDC1-1/2-K2 93167413R133 453 1 182JM5 3 182JM5 1 184JM
7-1/2 3 184JM 6-5/8” FPDC1-1/2-K2A 93167413R143 457-1/2 1 213JM 6-5/8” FPDC1-1/2-K3A 93167413R163 55
10 3 213JM8-3/8” FPDC1-1/2-K3 93167413R173 5510 1 215JM
15 3 215JM
DB2 3" x 2"
1-1/2 - 3 1 or 3 56C 4-1/2” FPDB2-K1 93167413R102 405 3 182JM
5-3/16” FPDB2-K2 93167413R113 505 1 184JM7-1/2 3 184JM7-1/2 1 213JM
6-7/16” FPDB2-K3 93167413R123 6010 3 213JM10 1 215JM15 3 215JM 7-1/4” FPDB2-K3A 93167413R193 6520 3 254JM 7-15/16” FPDB2-K4 93167413R204 70
DB3 4" x 3"
5 3 182JM4-15/16” FPDB3-K2 93167413R215 605 1 184JM
7-1/2 3 184JM7-1/2 1 213JM
5-3/4” FPDB3-K3 93167413R225 7010 3 213JM10 1 215JM15 3 215JM20 3 254JM 6” FPDB3-K4 93167413R236 75
DC4
4" x 4"
20 3 254JM7-15/32” FPDC4-K4 93167413R277 145
25 3 256JM30 3 284JM
9-1/32” FPDC4-K5 93167413R288 15540 3 286JM50 3 324JM
5" x 4" Flanged
20 3 254JM7-15/32” FPDC4-K4F 93167413R297 160
25 3 256JM30 3 284JM
9-1/32” FPDC4-K5F 93167413R308 17040 3 286JM50 3 324JM
Notes: Maximum O.D. impeller supplied with P.E. Kits. Impeller must be trimmed to match motor H.P. Refer to performance curves for specifi c impeller trim diameters. Consult catalog for specifi c trims sizes and performance. Impellers should be rebalanced after trimming.
PAGE: CP-440DATE: June 5, 2006
D SeriesPump End Kits - Ordering Information
DD
Centrifugal Pumps
D SeriesPump End Kits - Ordering Information
D SERIES CENTRIFUGAL PUMP END KITS for 1750 R.P.M. - O.D.P. MOTORS
SeriesSuction x Discharge
HP Range
PhaseMotor Frame
SizeMax. Imp.Diameter
PUMP END KITModel No. Order No. Wt.
DB1 1-1/2" x 1" 1/3 - 1/2 1 or 3 56C 6-7/16” FPDB1-K1 93167413R242 25
DB1-1/2 2" x 1-1/2" 1/3 - 1 1 or 3 56C 6-7/16” FPDB1-1/2-K1 93167413R252 30
DB2 3" x 2"1/2 - 3/4 1 or 3 56C 6-7/16” FPDB2-K1 93167413R262 40
1 - 1-1/2 1 or 3 56C 6-7/16” FPDB2-K2 93167413R272 40
Notes: Maximum O.D. impeller supplied with P.E. Kits. Impeller must be trimmed to match motor H.P. Consult catalog for specifi c trims sizes and performance. Impellers should be rebalanced after trimming.
Kit No. Frame Size FitK1 56
K2 145-182-184JM
K3 213-215JM
K4 254-256JM
K5 284-286-324-326JM
Mi8317
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
20
15
40
30
10
20
510
10
20
NP
SH
R -
FE
ET
4035302520151050
CAPACITY - GALLONS PER MINUTE
PS
I
TO
TA
L H
EA
D -
FE
ET
6-7/16” DIA.
6-1/8” DIA.
NPSHR
50%
52%
54%
56%
52%
50%
.5 BHP
.3 BHP
PAGE: CP-445DATE: June 5, 2006
DD
Model DB1 Performance1” Discharge x 1-1/2” Suction (1750 RPM)
DB11-1/2” Suction x 1” Discharge
Capacities GPMShut-off
Head (Ft.)
Total Head in Feet
HP Imp. Dia. 10 15 20 25 30 35 40 45 501/3 6-1/8” 39 33 26 16 38
1/2 6-7/16” 40 35 30 21 44
Note: 1750 RPM Models are available as D Series Pump End Kits only.
Centrifugal Pumps
0 20 40 60 80 100 120 140 160
CAPACITY - GALLONS PER MINUTE
6-7/16” DIA.
5-3/4” DIA.
5-1/8” DIA.
4-5/8” DIA.
60%
65%
67%
65%
60%
55%
NPSHR
1 BHP
.75 BHP
.5 BHP
.3 BHP
68%
20
40
15
30
10
20
510
TO
TA
L H
EA
D -
FE
ET
PS
I
10
20
30
NP
SH
R -
FE
ET
Model DB1-1/2 Performance1-1/2” Discharge x 2” Suction (1750 RPM)
DB1-1/2 2” Suction x 1-1/2” Discharge
Capacities GPMShut-off
Head (Ft.)
Total Head in Feet
HP Imp. Dia. 10 15 20 25 30 35 40 45 501/3 4-5/8” 64 50 24 21
1/2 5-1/8” 66 52 30 27
3/4 5-3/4” 84 70 54 35
1 6-7/16” 98 86 70 46 43
Note: 1750 RPM Models are available as D Series Pump End Kits only.
Mi8318
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
6-7/16” DIA.
5-13/16” DIA.
5-1/8” DIA.
4-7/8” DIA.
60%65%
70%
72%
70%
NPSHR
65%
60%
1.5 BHP
1 BHP
.75 BHP
.5 BHP
10
20
30
40
NP
SH
R -
FE
ET
140120100806040200
CAPACITY - GALLONS PER MINUTE
20
40
15
30
10
20
510
PS
I
TO
TAL
HE
AD
- F
EE
T
PAGE: CP-450DATE: June 5, 2006
Model DB2 Performance2” Discharge x 3” Suction (1750 RPM)
DB2 3” Suction x 2” Discharge
Capacities GPMShut-off
Head (Ft.)
Total Head in Feet
HP Imp. Dia. 10 15 20 25 30 35 40 45 501/2 4-7/8” 114 90 56 22
3/4 5-1/8” 112 88 25
1 5-13/16” 127 104 70 33
1-1/2 6-7/16” 156 144 128 108 69 42
Note: 1750 RPM Models are available as D Series Pump End Kits only. Performance supplied for D Series Pump End Kit sizing. Complete 1750 RPM units not available.
Mi8319
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
Model Number ExplanationExample: 7HC31575-CCPHAA
7 = 7.5 Horsepower (CC only) HC = Horizontal Centrifugal 3 = Suction Size 15 = Discharge Size 75 = Nominal Impeller Dia. CC = Close Coupled P = Shaft Sealing: P=Packing M=Mechanical Seal
HAA = Impeller Diameter (Alpha) A=0 F=5 L=10 B=1 G=6 M=11 C=2 H=7 N=12 D=3 J=8 P=13 E=4 K=9 Q=14
Features:■ 1-1/2” - 10” discharge sizes
■ Capacities to 7000 GPM, 480’ TDH
■ Horsepower: Up to 200 HP
■ Standard ductile iron construction with bronze wear ring and sleeve
■ Replaceable wear rings
■ Superior NPSH characteristics
■ 150# rated fl at faced fl anges
■ Heavy wall construction
■ Grade 5 capscrews
■ HC75 & HC10 Series- Enclosed impellers, internally hydraulically balanced
■ Double volute on HC10x10-14, for balanced radial forces, HC14 Series- External balance line standard
■ Standard with graphite packing or single mechanical seal
HC SeriesStandard Centrifugal Pumps- Close Coupled
PAGE: CP-700DATE: June 5, 2006
Mi8320
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
7.5” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Volute Design Motor Eff. HP-RPM Phase Shaft Sealing Order Number Weight
(Lbs.)
HC-3x15-75 3” x 1.5”
Flanged Std. Eff. 3-3600 1 Packing 50031575110 195Flanged Std. Eff. 5-3600 1 Packing 50031575130 205Flanged Std. Eff. 7.5-3600 1 Packing 50031575140 215Flanged Std. Eff. 10-3600 1 Packing 50031575150 248
HC-3x15-75 3” x 1.5”
Flanged Std. Eff. 3-3600 3 Packing 10031575110 195Flanged Std. Eff. 5-3600 3 Packing 10031575130 205Flanged Std. Eff. 7.5-3600 3 Packing 10031575140 215Flanged Std. Eff. 10-3600 3 Packing 10031575150 248
HC-3x15-75 3” x 1.5”
Flanged Std. Eff. 3-3600 1 Mech Seal 51031575111 195Flanged Std. Eff. 5-3600 1 Mech Seal 51031575131 205Flanged Std. Eff. 7.5-3600 1 Mech Seal 51031575141 215Flanged Std. Eff. 10-3600 1 Mech Seal 51031575151 248
HC-3x15-75 3” x 1.5”
Flanged Std. Eff. 3-3600 3 Mech Seal 11031575111 195Flanged Std. Eff. 5-3600 3 Mech Seal 11031575131 205Flanged Std. Eff. 7.5-3600 3 Mech Seal 11031575141 215Flanged Std. Eff. 10-3600 3 Mech Seal 11031575151 248
HC-3x2-75 3” x 2”
Flanged Std. Eff. 3-3600 1 Packing 50030275100 190Flanged Std. Eff. 5-3600 1 Packing 50030275110 200Flanged Std. Eff. 7.5-3600 1 Packing 50030275130 210Flanged Std. Eff. 10-3600 1 Packing 50030275140 243
HC-3x2-75 3” x 2”
Flanged Std. Eff. 3-3600 3 Packing 10030275100 190Flanged Std. Eff. 5-3600 3 Packing 10030275110 200Flanged Std. Eff. 7.5-3600 3 Packing 10030275130 210Flanged Std. Eff. 10-3600 3 Packing 10030275140 243Flanged Std. Eff. 15-3600 3 Packing 10030275150 257
HC-3x2-75 3” x 2”
Flanged Std. Eff. 3-3600 1 Mech Seal 51030275101 190Flanged Std. Eff. 5-3600 1 Mech Seal 51030275111 200Flanged Std. Eff. 7.5-3600 1 Mech Seal 51030275131 210Flanged Std. Eff. 10-3600 1 Mech Seal 51030275141 243
HC-3x2-75 3” x 2”
Flanged Std. Eff. 3-3600 3 Mech Seal 11030275101 190Flanged Std. Eff. 5-3600 3 Mech Seal 11030275111 200Flanged Std. Eff. 7.5-3600 3 Mech Seal 11030275131 210Flanged Std. Eff. 10-3600 3 Mech Seal 11030275141 243Flanged Std. Eff. 15-3600 3 Mech Seal 11030275151 257
HC-4x25-75 4” x 2.5”Flanged Std. Eff. 7.5-3600 1 Packing 50042575100 225Flanged Std. Eff. 10-3600 1 Packing 50042575110 258
HC-4x25-75 4” x 2.5”
Flanged Std. Eff. 7.5-3600 3 Packing 10042575100 225Flanged Std. Eff. 10-3600 3 Packing 10042575110 258Flanged Std. Eff. 15-3600 3 Packing 10042575130 272Flanged Std. Eff. 20-3600 3 Packing 10042575140 292Flanged Std. Eff. 25-3600 3 Packing 10042575150 302
HC-4x25-75 4” x 2.5”Flanged Std. Eff. 7.5-3600 1 Mech Seal 51042575101 225Flanged Std. Eff. 10-3600 1 Mech Seal 51042575111 258
HC-4x25-75 4” x 2.5”
Flanged Std. Eff. 7.5-3600 3 Mech Seal 11042575101 225Flanged Std. Eff. 10-3600 3 Mech Seal 11042575111 258Flanged Std. Eff. 15-3600 3 Mech Seal 11042575131 272Flanged Std. Eff. 20-3600 3 Mech Seal 11042575141 292Flanged Std. Eff. 25-3600 3 Mech Seal 11042575151 302
Ordering Information
PAGE: CP-705DATE: June 5, 2006
NOTES: Viton Seals available. Consult price sheets for list price adders. There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
HC-4x3-75 4” x 3”Flanged Std. Eff. 7.5-3600 1 Packing 50040375100 235Flanged Std. Eff. 10-3600 1 Packing 50040375110 268
HC-4x3-75 4” x 3”
Flanged Std. Eff. 7.5-3600 3 Packing 10040375100 235Flanged Std. Eff. 10-3600 3 Packing 10040375110 268Flanged Std. Eff. 15-3600 3 Packing 10040375120 282Flanged Std. Eff. 20-3600 3 Packing 10040375130 302Flanged Std. Eff. 25-3600 3 Packing 10040375140 312Flanged Std. Eff. 30-3600 3 Packing 10040375150 464
HC-4x3-75 4” x 3”Flanged Std. Eff. 7.5-3600 1 Mech Seal 51040375101 235Flanged Std. Eff. 10-3600 1 Mech Seal 51040375111 268
HC-4x3-75 4” x 3”
Flanged Std. Eff. 7.5-3600 3 Mech Seal 11040375101 235Flanged Std. Eff. 10-3600 3 Mech Seal 11040375111 268Flanged Std. Eff. 15-3600 3 Mech Seal 11040375121 282Flanged Std. Eff. 20-3600 3 Mech Seal 11040375131 302Flanged Std. Eff. 25-3600 3 Mech Seal 11040375141 312Flanged Std. Eff. 30-3600 3 Mech Seal 11040375151 464
HC-4x4-75 4” x 4”
Flanged Std. Eff. 15-3600 3 Packing 10040475100 282Flanged Std. Eff. 20-3600 3 Packing 10040475110 302Flanged Std. Eff. 25-3600 3 Packing 10040475120 312Flanged Std. Eff. 30-3600 3 Packing 10040475130 464Flanged Std. Eff. 40-3600 3 Packing 10040475140 502Flanged Std. Eff. 50-3600 3 Packing 10040475150 546
HC-4x4-75 4” x 4”
Flanged Std. Eff. 15-3600 3 Mech Seal 11040475101 282Flanged Std. Eff. 20-3600 3 Mech Seal 11040475111 302Flanged Std. Eff. 25-3600 3 Mech Seal 11040475121 312Flanged Std. Eff. 30-3600 3 Mech Seal 11040475131 464Flanged Std. Eff. 40-3600 3 Mech Seal 11040475141 502Flanged Std. Eff. 50-3600 3 Mech Seal 11040475151 546
HC-5x4-75 5” x 4”
Flanged Std. Eff. 25-3600 3 Packing 10050475100 449Flanged Std. Eff. 30-3600 3 Packing 10050475105 484Flanged Std. Eff. 40-3600 3 Packing 10050475110 522Flanged Std. Eff. 50-3600 3 Packing 10050475120 566Flanged Std. Eff. 60-3600 3 Packing 10050475130 569
HC-5x4-75 5” x 4”
Flanged Std. Eff. 25-3600 3 Mech Seal 11050475101 449Flanged Std. Eff. 30-3600 3 Mech Seal 11050475106 484Flanged Std. Eff. 40-3600 3 Mech Seal 11050475111 522Flanged Std. Eff. 50-3600 3 Mech Seal 11050475121 566Flanged Std. Eff. 60-3600 3 Mech Seal 11050475131 569
Mi8321
HC SeriesStandard Centrifugal Pumps- Close Coupled
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Ordering Information Cont.7.5” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor
Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Volute Design Motor Eff. HP-RPM Phase Shaft Sealing Order Number Weight
(Lbs.)
NOTES: Viton Seals available. Consult price sheets for list price adders. There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
HC-3x2-10 3” x 2”
Flanged Std. Eff. 10-3600 3 Packing 10030210100 315Flanged Std. Eff. 15-3600 3 Packing 10030210110 327Flanged Std. Eff. 20-3600 3 Packing 10030210115 322Flanged Std. Eff. 25-3600 3 Packing 10030210120 337Flanged Std. Eff. 30-3600 3 Packing 10030210130 484Flanged Std. Eff. 10-3600 1 Packing 50030210100 315
HC-3x2-10 3” x 2”
Flanged Std. Eff. 10-3600 3 Mech Seal 11030210101 315Flanged Std. Eff. 15-3600 3 Mech Seal 11030210111 327Flanged Std. Eff. 20-3600 3 Mech Seal 11030210116 322Flanged Std. Eff. 25-3600 3 Mech Seal 11030210121 337Flanged Std. Eff. 30-3600 3 Mech Seal 11030210131 484Flanged Std. Eff. 10-1800 1 Mech Seal 51030210101 315
HC-4x25-10 4” x 2.5”
Flanged Std. Eff. 15-3600 3 Packing 10042510100 354Flanged Std. Eff. 20-3600 3 Packing 10042510105 327Flanged Std. Eff. 25-3600 3 Packing 10042510110 347Flanged Std. Eff. 30-3600 3 Packing 10042510115 494Flanged Std. Eff. 40-3600 3 Packing 10042510120 532Flanged Std. Eff. 50-3600 3 Packing 10042510125 576Flanged Std. Eff. 60-3600 3 Packing 10042510130 579Flanged Std. Eff. 2-1800 3 Packing 20042510100 230Flanged Std. Eff. 3-1800 3 Packing 20042510110 249Flanged Std. Eff. 5-1800 3 Packing 20042510120 265Flanged Std. Eff. 7.5-1800 3 Packing 20042510130 278
HC-4x25-10 4” x 2.5”Flanged Std. Eff. 5-1800 1 Packing 50042510120 265Flanged Std. Eff. 7.5-1800 1 Packing 50042510130 278
HC-4x25-10 4” x 2.5”
Flanged Std. Eff. 15-3600 3 Mech Seal 11042510101 354Flanged Std. Eff. 20-3600 3 Mech Seal 11042510106 327Flanged Std. Eff. 25-3600 3 Mech Seal 11042510111 347Flanged Std. Eff. 30-3600 3 Mech Seal 11042510116 494Flanged Std. Eff. 40-3600 3 Mech Seal 11042510121 532Flanged Std. Eff. 50-3600 3 Mech Seal 11042510126 576Flanged Std. Eff. 60-3600 3 Mech Seal 11042510131 579Flanged Std. Eff. 2-1800 3 Mech Seal 21042510101 230Flanged Std. Eff. 3-1800 3 Mech Seal 21042510111 249Flanged Std. Eff. 5-1800 3 Mech Seal 21042510121 265Flanged Std. Eff. 7.5-1800 3 Mech Seal 21042510131 278
HC-4x25-10 4” x 2.5”Flanged Std. Eff. 5-1800 1 Mech Seal 51042510121 265Flanged Std. Eff. 7.5-1800 1 Mech Seal 51042510131 278
HC-4x3-10 4” x 3”
Flanged Std. Eff. 30-3600 3 Packing 10040310100 489Flanged Std. Eff. 40-3600 3 Packing 10040310110 527Flanged Std. Eff. 50-3600 3 Packing 10040310120 571Flanged Std. Eff. 60-3600 3 Packing 10040310125 574Flanged e-pact eff. 75-3600 3 Packing 10040310130 662Flanged e-pact eff. 100-3600 3 Packing 10040310140 708
HC-4x3-10 4” x 3”
Flanged Std. Eff. 30-3600 3 Mech Seal 11040310101 489Flanged Std. Eff. 40-3600 3 Mech Seal 11040310111 527Flanged Std. Eff. 50-3600 3 Mech Seal 11040310121 571Flanged Std. Eff. 60-3600 3 Mech Seal 11040310126 574Flanged e-pact eff. 75-3600 3 Mech Seal 11040310131 662Flanged e-pact eff. 100-3600 3 Mech Seal 11040310141 708
HC SeriesStandard Centrifugal Pumps- Close Coupled
Ordering Information Cont.
PAGE: CP-710DATE: June 5, 2006
10” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Volute Design Motor Eff. HP-RPM Phase Shaft Sealing Order Number Weight
(Lbs.)
NOTES: Viton Seals available. Consult price sheets for list price adders. There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
Mi8346
HC SeriesStandard Centrifugal Pumps- Close Coupled
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Ordering Information Cont.
HC-6x4-10 6” x 4”
Flanged Std. Eff. 30-3600 3 Packing 10060410100 552Flanged Std. Eff. 40-3600 3 Packing 10060410105 592Flanged Std. Eff. 50-3600 3 Packing 10060410110 636Flanged Std. Eff. 60-3600 3 Packing 10060410115 639Flanged e-pact eff. 75-3600 3 Packing 10060410120 727Flanged e-pact eff. 100-3600 3 Packing 10060410130 773Flanged e-pact eff. 125-3600 3 Packing 10060410140 848
HC-6x4-10 6” x 4”
Flanged Std. Eff. 30-3600 3 Mech Seal 11060410101 552Flanged Std. Eff. 40-3600 3 Mech Seal 11060410106 592Flanged Std. Eff. 50-3600 3 Mech Seal 11060410111 636Flanged Std. Eff. 60-3600 3 Mech Seal 11060410116 639Flanged e-pact eff. 75-3600 3 Mech Seal 11060410121 727Flanged e-pact eff. 100-3600 3 Mech Seal 11060410131 773Flanged e-pact eff. 125-3600 3 Mech Seal 10060410141 848
HC-8x6-95 8” x 6”
Flanged Std. Eff. 15-1800 3 Packing 20080695100 544Flanged Std. Eff. 20-1800 3 Packing 20080695110 577Flanged Std. Eff. 25-1800 3 Packing 20080695120 625Flanged e-pact eff. 5-1200 3 Packing 30080695100 455Flanged e-pact eff. 7.5-1200 3 Packing 30080695110 468
HC-8x6-95 8” x 6”
Flanged Std. Eff. 15-1800 3 Mech Seal 21080695101 544Flanged Std. Eff. 20-1800 3 Mech Seal 21080695111 577Flanged Std. Eff. 25-1800 3 Mech Seal 21080695121 625Flanged e-pact eff. 5-1200 3 Mech Seal 31080695101 455Flanged e-pact eff. 7.5-1200 3 Mech Seal 31080695111 468
HC-8x6-10 8” x 6”
Flanged Std. Eff. 20-1800 3 Packing 20080610100 582Flanged Std. Eff. 30-1800 3 Packing 20080610110 672Flanged Std. Eff. 40-1800 3 Packing 20080610120 777Flanged e-pact eff. 5-1200 3 Packing 30080610100 500Flanged e-pact eff. 7.5-1200 3 Packing 30080610110 535Flanged e-pact eff. 10-1200 3 Packing 30080610120 600
HC-8x6-10 8” x 6”
Flanged Std. Eff. 20-1800 3 Mech Seal 21080610101 582Flanged Std. Eff. 30-1800 3 Mech Seal 21080610111 672Flanged Std. Eff. 40-1800 3 Mech Seal 21080610121 777Flanged e-pact eff. 5-1200 3 Mech Seal 31080610101 500Flanged e-pact eff. 7.5-1200 3 Mech Seal 31080610111 535Flanged e-pact eff. 10-1200 3 Mech Seal 31080610121 600
10” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Volute Design Motor Eff. HP-RPM Phase Shaft Sealing Order Number Weight
(Lbs.)
NOTES: Viton Seals available. Consult price sheets for list price adders. There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
Ordering Information Cont.
PAGE: CP-715DATE: June 5, 2006
HC-5x3-14 5” x 3”
Flanged Std. Eff. 20-1800 3 Packing 20050314100 572Flanged Std. Eff. 25-1800 3 Packing 20050314110 600Flanged Std. Eff. 30-1800 3 Packing 20050314120 642Flanged Std. Eff. 40-1800 3 Packing 20050314130 747
HC-5x3-14 5” x 3”
Flanged Std. Eff. 20-1800 3 Mech Seal 21050314101 572Flanged Std. Eff. 25-1800 3 Mech Seal 21050314111 600Flanged Std. Eff. 30-1800 3 Mech Seal 21050314121 642Flanged Std. Eff. 40-1800 3 Mech Seal 21050314131 747
HC-6x4-13 6” x 4”
Flanged Std. Eff. 30-1800 3 Packing 20060413100 647Flanged Std. Eff. 40-1800 3 Packing 20060413110 752Flanged Std. Eff. 50-1800 3 Packing 20060413120 807Flanged Std. Eff. 60-1800 3 Packing 20060413130 838
HC-6x4-13 6” x 4”
Flanged Std. Eff. 30-1800 3 Mech Seal 21060413101 647Flanged Std. Eff. 40-1800 3 Mech Seal 21060413111 752Flanged Std. Eff. 50-1800 3 Mech Seal 21060413121 807Flanged Std. Eff. 60-1800 3 Mech Seal 21060413131 838
HC-6x6-14 6” x 6”
Flanged e-pact eff. 40-1800 3 Packing 20060414100 842Flanged e-pact eff. 50-1800 3 Packing 20060414110 897Flanged e-pact eff. 60-1800 3 Packing 20060414120 928Flanged e-pact eff. 75-1800 3 Packing 20060414130 1005Flanged e-pact eff. 100-1800 3 Packing 20060414140 1247
HC-6x6-14 6” x 6”
Flanged e-pact eff. 40-1800 3 Mech Seal 21060414101 842Flanged e-pact eff. 50-1800 3 Mech Seal 21060414111 897Flanged e-pact eff. 60-1800 3 Mech Seal 21060414121 928Flanged e-pact eff. 75-1800 3 Mech Seal 20060414131 1005Flanged e-pact eff. 100-1800 3 Mech Seal 21060414141 1247
HC-8x6-14 8” x 6”
Flanged e-pact eff. 75-1800 3 Packing 20080614100 1110Flanged e-pact eff. 100-1800 3 Packing 20080614110 1352Flanged e-pact eff. 125-1800 3 Packing 20080614120 1492Flanged e-pact eff. 150-1800 3 Packing 20080614130 2038Flanged e-pact eff. 20-1200 3 Packing 30080614100 915Flanged e-pact eff. 25-1200 3 Packing 30080614110 955Flanged e-pact eff. 30-1200 3 Packing 30080614120 985Flanged e-pact eff. 40-1200 3 Packing 30060814130 1125
HC-8x6-14 8” x 6”
Flanged e-pact eff. 75-1800 3 Mech Seal 21080614101 1110Flanged e-pact eff. 100-1800 3 Mech Seal 21080614111 1352Flanged e-pact eff. 125-1800 3 Mech Seal 21080614121 1492Flanged e-pact eff. 150-1800 3 Mech Seal 21080614131 2038Flanged e-pact eff. 20-1200 3 Mech Seal 31080614101 915Flanged e-pact eff. 25-1200 3 Mech Seal 31080614111 955Flanged e-pact eff. 30-1200 3 Mech Seal 31080614121 985Flanged e-pact eff. 40-1200 3 Mech Seal 31080614131 1125
14” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Volute Design Motor Eff. HP-RPM Phase Shaft Sealing Order Number Weight
(Lbs.)
NOTES: Viton Seals available. Consult price sheets for list price adders. There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
Ordering Information Cont.
Mi8322
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
HC-10x10-14 10” x 10”
Flanged e-pact eff. 100-1800 3 Packing 20101014100 1597Flanged e-pact eff. 125-1800 3 Packing 20101014110 1737Flanged e-pact eff. 150-1800 3 Packing 20101014120 2298Flanged e-pact eff. 200-1800 3 Packing 20101014130 2365Flanged e-pact eff. 25-1200 3 Packing 30101014100 1330Flanged e-pact eff. 40-1200 3 Packing 30101014110 1370Flanged e-pact eff. 50-1200 3 Packing 30101014120 1410Flanged e-pact eff. 60-1200 3 Packing 30101014130 1630
HC-10x10-14 10” x 10”
Flanged e-pact eff. 100-1800 3 Mech Seal 21101014101 1597Flanged e-pact eff. 125-1800 3 Mech Seal 21101014111 1737Flanged e-pact eff. 150-1800 3 Mech Seal 21101014121 2298Flanged e-pact eff. 200-1800 3 Mech Seal 21101014131 2365Flanged e-pact eff. 25-1200 3 Mech Seal 31101014101 1330Flanged e-pact eff. 40-1200 3 Mech Seal 31101014111 1370Flanged e-pact eff. 50-1200 3 Mech Seal 31101014121 1410Flanged e-pact eff. 60-1200 3 Mech Seal 31101014131 1630
14” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Volute Design Motor Eff. HP-RPM Phase Shaft Sealing Order Number Weight
(Lbs.)
NOTES: Viton Seals available. Consult price sheets for list price adders. There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
PAGE: CP-720DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps- Close Coupled
7.5” (15 HP)
7.0” (10 HP)
6.5” (7.5 HP)
5.5” (5 HP)
5.0” (3 HP)
40 5060 6 FT
65
678 FT
65
60
15 HP
10 HP
7.5 HP
5 HP3 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 25 50 75 100 125 150 175 200 225 250 275
0 5 10 15 20 25 30 35 40 45 50 55 60 65
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0
10
20
30
40
50
60
70
80
90
0
50
100
150
200
250
300
SIZE: 3” x 2”IMPELLER DIA: VariousSPEED: 3550 RPM
Model HC-3x2-75
7.5” (10 HP)
7.0” (7.5 HP)
6.5” (5 HP)
5.5” (3 HP)
30 40
6 FT NPSHR
50 55 588 FT
9 FT
10 FT58
55
50
10 HP
7.5 HP
5 HP
3 HP2 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 10 20 30 40 50 60 70 80 90 100 110 120 130
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0
10
20
30
40
50
60
70
80
90
40
80
120
160
200
240
280
SIZE: 3” x 1.5”IMPELLER DIA: VariousSPEED: 3525 RPM
Model HC-3x15-75
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
Mi8323
Model HC-4x3-75
7.5” (25 HP)
7.0” (20 HP)
6.5” (15 HP)
5.5” (10 HP)
5.0” (7.5 HP)
5 HP
7.5 HP10 HP
15 HP20 HP
25 HP
30 HP
40 50 6070
75
75
77
70
60
50
5 FT NPSHR7 FT
9 FT
12 FT
15 FT
0 50 100 150 200 250 300 350 400 450 500 550FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130
TO
TAL
HE
AD
- M
ET
ER
S
0
10
20
30
40
50
60
70
80
90
TO
TAL
HE
AD
- F
EE
T
40
80
120
160
200
240
280
SIZE: 4” x 2.5”IMPELLER DIA: VariousSPEED: 3575 RPM
Model HC-4x25-75
7.5” (30 HP)
7.0” (25 HP)
6.5” (20 HP)
6.0” (15 HP)
5.5” (10 HP)
5.0” (7.5 HP)
8 FT NPSHR
40 50 60
7570 9 FT
10 FT
78 12 FT
7515 FT
70
30 HP25 HP
20 HP
15 HP
10 HP7.5 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 50 100 150 200 250 300 350 400 450 500 550 600 650
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0
10
20
30
40
50
60
70
80
90
0
40
80
120
160
200
240
280
SIZE: 4” x 3”IMPELLER DIA: VariousSPEED: 3570 RPM
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-725DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps- Close Coupled
Model HC-5x4-75
7.5” (50 HP)
7.0” (40 HP)
6.5” (30 HP)
6.0” (25 HP)
5.5” (20 HP)
5.0” (15 HP)
40 50 6070
75
70
60
50 HP
18 FT
40 HP
30 HP
25 HP
20 HP15 HP
15 FT
10 HP
13 FT
12 FT11 FT
10 FT
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 100 200 300 400 500 600 700 800 900 1000 1100
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260
TOTA
L H
EA
D -
ME
TE
RS
TOTA
L H
EA
D -
FE
ET
0
10
20
30
40
50
60
70
80
90
0
40
80
120
160
200
240
280
SIZE: 4” x 4”IMPELLER DIA: VariousSPEED: 3550 RPM
Model HC-4x4-75
7.5” (60 HP)
7.0” (50 HP)
6.5” (40 HP)
6.0” (25 HP)
6.25” (30 HP)
DO NOT OPERATE CONTINUOUSLYBELOW 350 GPM
15 FT NPSHR
40 50 6070
8082
16 FT
80
17 FT
19 FT
22 FT
70
60
60 HP50
50 HP40 HP
30 HP
25 HP
20 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0
10
20
30
40
50
60
70
80
90
0
40
80
120
160
200
240
280
SIZE: 5” x 4”IMPELLER DIA: VariousSPEED: 3575 RPM
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
Mi8324
9.0” (25 HP)
8.5” (20 HP)
8.0” (15 HP)
7.0” (10 HP)
10.25” ( 30 HP)
9 FT NPSH REQ’D
45
3040
50 9 FT
54
9 FT
9 FT54
40 HP
30 HP
25 HP
20 HP45
11 FT
10 HP7.5 HP
15 HP
9 FT
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 25 50 75 100 125 150 175 200 225 250 275
0 5 10 15 20 25 30 35 40 45 50 55 60 65
TOTA
L H
EA
D -
ME
TER
S
30
40
50
60
70
80
90
100
110
120
130
140
150
TOTA
L H
EA
D -
FEE
T
100
150
200
250
300
350
400
450
500
SIZE: 3” x 2”IMPELLER DIA: VariousSPEED: 3570 RPM
Model HC-3x2-10
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-730DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps- Close Coupled
Model HC-4x25-10
SIZE: 4” x 2.5”IMPELLER DIA: VariousSPEED: 1780 RPM
10.25” (7.5 HP)
9.0” (5 HP)
8.0” (3 HP)
7.0” (2 HP)
4050
2 FT NPSHR
6065
70
65
1.5 FT
2 FT2.5 FT
7.5 HP
60
5 HP
3 HP2 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 25 50 75 100 125 150 175 200 225 250 275
0 5 10 15 20 25 30 35 40 45 50 55 60 65
TOTA
L H
EA
D -
ME
TER
S
TOTA
L H
EA
D -
FEE
T
0
5
10
15
20
25
30
35
40
45
0
20
40
60
80
100
120
140
Model HC-4x25-10
10.25” (60 HP)
9.0” (40 HP)
8.38” (30 HP)
9.5” (50 HP)
8.0” (25 HP)
7.38” (20 HP)
7.0” (15 HP)
40 50
8 FT NPSHR
6065
6 FT
70
8 FT10 FT
65
60 HP
50 HP
40 HP
30 HP
25 HP20 HP
60
15 HP
FLOWRATE U.S. GALLONS PER MINUTE
500 100 150 200 250 300 350 400 450 500 550
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130
80
160
240
320
400
480
560
TO
TAL
HE
AD
- M
ET
ER
S
0
20
40
60
80
100
120
140
160
180
SIZE: 4” x 2.5”IMPELLER DIA: VariousSPEED: 3575 RPM
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
Mi8325
Model HC-6x4-10
10.25” ( 100 HP)
8” (40 HP)
8.75” (50 HP)
9.25” (60 HP)
9.75” (75 HP)
7” (30 HP)
45 5565
6 FT NPSHR
7 FT
70
9 FT
72 11 FT14 FT
15 FT70
65
100 HP
75 HP
55 60 HP50 HP
40 HP30 HP
20 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 80 160 240 320 400 480 560 640 720 800 880
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128 136 144 152 160 168 176 184 192 200 208
TOTA
L H
EA
D -
ME
TE
RS
TOTA
L H
EA
D -
FE
ET
0
20
40
60
80
100
120
140
160
180
80
160
240
320
400
480
560
SIZE: 4” x 3”IMPELLER DIA: VariousSPEED: 3570 RPM
Model HC-4x3-10
10.25” (125 HP)
9.0” (75 HP)
9.75” (100 HP)
8.0” (50 HP)
7.5” (40 HP)
8.38” (60 HP)
7.0” (30 HP)
40 50 6070
8 FT NPSHR
12 FT
84
15 FT
18 FT
80125 HP
75
70
60
50
30 HP15 FT
40 HP50 HP 60 HP
75 HP
100 HP
18 FT
7510 FT
80
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 100 200 300 400 500 600 700 800 900 1000 1100
0 20 40 60 80 100 120 140 160 180 200 220 240 260
0
20
40
60
80
100
120
140
160
180
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
80
160
240
320
400
480
560
SIZE: 6” x 4”IMPELLER DIA: VariousSPEED: 3550 RPM
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-735DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps- Close Coupled
Model HC-8x6-95
SIZE: 8” x 6”IMPELLER DIA: VariousSPEED: 1150 RPM
9.5 @ 13˚ (7.5 HP)
9.0 @ 15˚ (5 HP)
40 506.5 FT
6070
87
86
7 FT9.5 FT80
13 FT
80
70
60
503 HP
5 HP
7.5 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 100 200 300 400 500 600 700 800 900 1000 1100
0 20 40 60 80 100 120 140 160 180 200 220 240 260
TOTA
L H
EA
D -
ME
TER
S
TOTA
L H
EA
D -
FEE
T
0
1
2
3
4
5
6
7
8
9
10
11
0
5
10
15
20
25
30
35
Model HC-8x6-95
7 FT NPSH REQ’D
8 FT60 %
70 % 80%
85%
88%
8 FT
84%
10 FT
15 FT20 FT
25 FT
80%
28 FT
70%
25 HP
20 HP
15 HP10 HP
40% 50%
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
0 40 80 120 160 200 240 280 320 360 400 440 480 520
TOTA
L H
EA
D -
ME
TER
S
TOTA
L H
EA
D -
FEE
T
0
5
10
15
20
25
30
35
40
45
20
40
60
80
100
120
140
SIZE: 8” x 6”IMPELLER DIA: VariousSPEED: 1780 RPM
9.5” (25 HP)
9” (20 HP)
8.5” (15 HP)
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
Mi8326
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Model HC-8x6-10
SIZE: 8” x 6”IMPELLER DIA: VariousSPEED: 1150 RPM
10.25” (10 HP)
9.25” (7.5 HP)
8.50” (5 HP)
40 50 60 70
5 FT NPSH REQ’D
5 FT
8481
7 FT
80
8011 FT
13 FT
7010 HP
7.5 HP
5 HP3 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 100 200 300 400 500 600 700 800 900 1000 1100 1200
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280
TOTA
L H
EA
D -
ME
TE
RS
TOTA
L H
EA
D -
FE
ET
- E
FF
ICIE
NC
Y (
%)
0
5
10
15
20
0
10
20
30
40
50
60
70
Model HC-8x6-10
9.00” (20 HP)
9.25” (30 HP)
10.25” (40 HP)40% 50%
60% 70%
11 FT. NPSH REQ’D
11 FT15 FT
80%25 FT
30 FT
70%
40 HP
30 HP25 HP
20 HP
15 HP10 HP
81%84%
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
0 40 80 120 160 200 240 280 320 360 400 440 480 520
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T -
EF
FIC
IEN
CY
(%)
0
5
10
15
20
25
30
35
40
45
20
40
60
80
100
120
140
SIZE: 8” x 6”IMPELLER DIA: VariousSPEED: 1760 RPM
Centrifugal Pumps
PAGE: CP-740DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps- Close Coupled
Model HC-5x3-14
SIZE: 6” x 4”IMPELLER DIA: VariousSPEED: 1780 RPM
13.0” (60 HP)
12.0” (50 HP)
11.0” (40 HP)
10.0” (30 HP)
50 60 70
4 FT NPSH REQ’D
7680
5 FT
82
83
8 FT10 FT
8015 FT
23 FT
76
60 HP
50 HP
40 HP
30 HP
25 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
00
40
80
120
160
200
240
280
0
20
40
60
80
Model HC-6x4-13
14.0” (40 HP)
13.0” (30 HP)
12.0” (25 HP)
11.0” (20 HP)
50% 60% 65%70%
6 FT
7 FT
73%
70%9 FT
65% 10.5 FT
60%
50%
50 HP
40 HP
30 HP
25 HP20 HP
15 HP
5 FT5 FT
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 80 160 240 320 400 480 560 640 720 800 880
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0
10
20
30
40
50
60
70
80
90
0
40
80
120
160
200
240
280
SIZE: 5” x 3”IMPELLER DIA: VariousSPEED: 1780 RPM
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
Mi8327
10” (40 HP)
11” (50 HP)
12” (60 HP)
13” (75 HP)
14” (100 HP)
30 HP
40 HP50 HP
60 HP
75 HP
100 HP
6 FT
60
8 FT
70 75
10 FT
80
12 FT
8215 FT
17 FT
80
7570
50
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
250 500 750 1000 1250 1500 1750 2000 2250 2500 2750
0 50 100 150 200 250 300 350 400 450 500 550 600 650
0
20
40
60
80
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0
40
80
120
160
200
240
280
SIZE: 6” x 6”IMPELLER DIA: VariousSPEED: 1760 RPM
Model HC-6x6-14
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-745DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps- Close Coupled
Model HC-8x6-14
SIZE: 8” x 6”IMPELLER DIA: VariousSPEED: 1170 RPM
14” (40 HP)
13” (30 HP)
12” (25 HP)
11” (20 HP)
40 50 60 70
4 FT NPSH REQ’D
75 80
5.5 FT
85 87
85
6 FT7.5 FT
11 FT
80 50 HP
20 HP
25 HP30 HP
40 HP
15 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400
0 40 80 120 160 200 240 280 320 360 400 440 480 520 560
TOTA
L H
EA
D -
ME
TER
S
TOTA
L H
EA
D -
FEE
T
0
10
20
30
40
0
20
40
60
80
100
120
140
Model HC-8x6-14
14.0” (150 HP)
13.0” (125 HP)
12.0” (100 HP)
11.0” (75 HP)
60 HP
75 HP
100 HP
150 HP
60 70 75 80
85
85 87
80
9 FT NPSH REQ’D12 FT 14 FT
17 FT
25 FT
500 500045004000350030002500200015001000 5500FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0
25
50
75
100
0
50
100
150
200
250
300
350
SIZE: 8” x 6”IMPELLER DIA. VariousSPEED: 1780 RPM
125 HP
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Close Coupled
Mi8328
SIZE: 10” x 10”IMPELLER DIA: VariousSPEED: 1180 RPM
14” (60 HP)
13” (50 HP)
12” (40 HP)
11” (25 HP)
7 FT NPSH REQ’D
70 7580
9 FT
8511 FT
87
85
14 FT
8075
60 HP50 HP
40 HP30 HP
20 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 4400
0 100 200 300 400 500 600 700 800 900 1000
TOTA
L H
EA
D -
ME
TER
S
TOTA
L H
EA
D -
FEE
T
0
10
20
30
40
0
20
40
60
80
100
120
140
Model HC-10x10-14
SIZE: 10” x 10”IMPELLER DIA: VariousSPEED: 1780 RPM
14” (200 HP)
13” (150 HP)
12” (125 HP)
11” (100 HP)
12 FT NPSH REQ’D
70 7580
17 FT
85
20 FT
87
85
25 FT
8075
200 HP150 HP
125 HP100 HP
75 HP
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 60000
0 125 250 375 500 625 750 875 1000 1125 1250 1375
TOTA
L H
EA
D -
ME
TER
S
TOTA
L H
EA
D -F
EE
T
0
20
40
60
80
0
40
80
120
160
200
240
280
EFF
ICIE
NC
Y
10
20
30
40
50
60
70
80
Model HC-10x10-14
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
Model Number ExplanationExample: HC31575-BFP
HC = Horizontal Centrifugal 3 = Suction Size 15 = Discharge Size 75 = Nominal Impeller Dia. BF = Bearing Frame P = Shaft Sealing: P=Packing M=Mechanical Seal
Features:■ 1-1/2” - 10” discharge sizes
■ Capacities to 7000 GPM, 480’ TDH
■ Horsepower: Up to 200 HP
■ Standard ductile iron construction with bronze wear ring and sleeve
■ Replaceable wear rings
■ Superior NPSH characteristics
■ 150# rated fl at faced fl anges
■ Heavy wall construction
■ Grade 5 capscrews
■ HC75 & HC10 Series- Enclosed impellers, internally hydraulically balanced
■ Double volute on HC10x10-14, for balanced radial forces, HC14 Series- External balance line standard
■ Standard with graphite packing or single mechanical seal
HC SeriesStandard Centrifugal Pumps- Bearing Frame
PAGE: CP-755DATE: June 5, 2006
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps- Bearing Frame
Ordering Information7.5” Nominal Impeller Diameter - (BF) Bearing Frame w/Electric Motor
Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft SleevePump Model Suction/Disch Size Rotation Shaft Sealing Order Number Weight (Lbs.)
HC-3X15-75-BF-P 3” x 1.5” CW Packing 14031575100 245
HC-3X15-75-BF-M 3” x 1.5” CW Mech Seal 15031575101 245
HC-3X2-75-BF-P 3” x 2” CW Packing 14030275100 245
HC-3X2-75-BF-M 3” x 2” CW Mech Seal 15030275101 245
HC-4X25-75-BF-P 4” x 2.5” CW Packing 14042575100 255
HC-4X25-75-BF-M 4” x 2.5” CW Mech Seal 15042575101 255
HC-4X3-75-BF-P 4” x 3” CW Packing 14040375100 265
HC-4X3-75-BF-M 4” x 3” CW Mech Seal 15040375101 265
HC-4X4-75-BF-P 4” x 4” CW Packing 14040475100 265
HC-4X4-75-BF-M 4” x 4” CW Mech Seal 15040475101 265
HC-5X4-75-BF-P 5” x 4” CW Packing 14050475100 285
HC-5X4-75-BF-M 5” x 4” CW Mech Seal 15050475101 285
10” Nominal Impeller Diameter - (BF) Bearing Frame w/Electric Motor Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Rotation Shaft Sealing Order Number Weight (Lbs.)HC-3X2-10-BF-P 3” x 2” CW Packing 14030210100 395
HC-3X2-10-BF-M 3” x 2” CW Mech Seal 15030210101 395
HC-4X25-10-BF-P 4” x 2.5” CW Packing 14042510100 405
HC-4X25-10-BF-M 4” x 2.5” CW Mech Seal 15042510101 405
HC-4X3-10-BF-P 4” x 3” CW Packing 14040310100 405
HC-4X3-10-BF-M 4” x 3” CW Mech Seal 15040310101 405
HC-6X4-10-BF-P 6” x 4” CW Packing 14060410100 465
HC-6X4-10-BF-M 6” x 4” CW Mech Seal 15060410101 465
HC-8X6-95-BF-P 8” x 6” CW Packing 14080695100 595
HC-8X6-95-BF-M 8” x 6” CW Mech Seal 15080695101 595
HC-8X6-10-BF-P 8” x 6” CW Packing 14080610100 600
HC-8X6-10-BF-M 8” x 6” CW Mech Seal 15080610101 600
14” Nominal Impeller Diameter - (BF) Bearing Frame w/Electric Motor Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Rotation Shaft Sealing Order Number Weight (Lbs.)HC-5X3-14-BF-P 5” x 3” CW Packing 14050314100 590
HC-5X3-14-BF-M 5” x 3” CW Mech Seal 15050314101 590
HC-6X4-13-BF-P 6” x 4” CW Packing 14060413100 595
HC-6X4-13-BF-M 6” x 4” CW Mech Seal 15060413101 595
HC-6X6-14-BF-P 6” x 6” CW Packing 14060614100 700
HC-6X6-14-BF-M 6”x 6” CW Mech Seal 15060614101 700
HC-8X6-14-BF-P 8” x 6” CW Packing 14080614100 805
HC-8X6-14-BF-M 8” x 6” CW Mech Seal 15080614101 805
HC-10X10-14-BF-P 10” x 10” CW Packing 14101014500 1070
HC-10X10-14-BF-M 10” x 10” CW Mech Seal 15101014501 1070
Mi8329
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
NOTES: Viton Seals available. Consult price sheets for list price adders. There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
00
30
60
90
120
150
180
210
240
270
300
20 40 60 80 100 120 140 160 180 200 220 240 260 280
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
3550 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
2300 RPM
SIZE: 3” x 2”IMPELLER DIA: 7.50”SPEED: 3550 RPM
NP
SH
R -
FE
ET
0 105 15 25 35 45 5520 30 40 50
5056
6164
66
66
64
61
56
503 HP
5 HP
7.5 HP
10 HP
7.5
15
NPSHR - 3550 RPM
0
10
20
30
40
50
60
70
80
90
PAGE: CP-760DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-Bearing Frame
00
30
60
90
120
150
180
210
240
270
300
10 20 30 40 50 60 70 80 90 100 110 120 130 140
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
3530 RPM
3400 RPM
3200 RPM
2800 RPM
3000 RPM
2500 RPM
2300 RPM
SIZE: 3” x 1.5”IMPELLER DIA: 7.50”SPEED: 3530 RPM
NP
SH
R -
FE
ET
0
7.5
15
0
10
20
30
40
50
60
70
80
90
38 44 50 5558
59
5859
55
50
44
2 HP
3 HP
5 HP
7.5 HP
NPSHR - 3530 RPM
5 10 15 20 25 30
Model HC-3x15-75
Model HC-3x2-75
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps-Bearing Frame
Mi8330
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
00
30
60
90
120
150
180
210
240
270
300
50 100 150 200 250 300 350 400 450 500 550 600 650
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 4” x 2.5”IMPELLER DIA: 7.50”SPEED: 3580 RPM
NP
SH
R -
FE
ET
0
15
30
0
10
20
30
40
50
60
70
80
90
NPSHR - 3580 RPM
10
3580 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2600 RPM
2400 RPM
20 30 40 50 60 70 80 90 100 110 120 130 140
57 6470
7477
77
74
70
64
57
25 HP20 HP
15 HP
10 HP
7.5 HP
Model HC-4x25-75
00
30
60
90
120
150
180
210
240
270
300
50 100 150 200 250 300 350 400 450 500 550 600 650 700 750
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 4” x 3”IMPELLER DIA: 7.50”SPEED: 3570 RPM
NP
SH
R -
FE
ET
0
15
30
0
10
20
30
40
50
60
70
80
90
NPSHR - 3570 RPM
10
3570 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
2400 RPM
5965
7174
7677
7776
74
71
65
30 HP25 HP
20 HP
15 HP
10 HP7.5 HP
20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Model HC-4x3-75
Centrifugal Pumps
PAGE: CP-765DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-Bearing Frame
00
30
60
90
120
150
180
210
240
270
300
200 400 600 800 1000 1200 1400
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
3580 RPM
3400 RPM
3200 RPM
3000 RPM
2900 RPM
SIZE: 5” x 4”IMPELLER DIA: 7.50”SPEED: 3580 RPM
NP
SH
R -
FE
ET
0 50 100 150 200 250 350300
20
40
NPSHR - 3580 RPM
0
10
20
30
40
50
60
70
80
90
56 6471
7680
81
8180
76
71
64
56
60 HP50 HP40 HP
30 HP25 HP
00
30
60
90
120
150
180
210
240
270
300
100 200 300 400 500 600 700 800 900 1000
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 4” x 4”IMPELLER DIA: 7.50”SPEED: 3550 RPM
0
0
10
20
30
40
50
60
70
80
90
3550 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2600 RPM
2300 RPM50.0 HP
20 40 90 100 140 160 180 200 220
NP
SH
R -
FE
ET
30
15
40.0 HP
30.0 HP25.0 HP
20.0 HP15.0 HP
12060
55 61 6771
7475
7574
71
67
61
55
NPSHR - 3550 RPM
Model HC-4x4-75
Model HC-5x4-75
Mi8331
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-766DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-Bearing Frame
Model HC-3x2-10
00
80
160
240
320
400
480
560
640
720
800
20 40 60 80 100 120 140 160 180 200 220 240 260
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
3743
4852
5455
5554
52
48
7.5 HP
10 HP 15 HP
20 HP
25 HP30 HP
3570 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
2400 RPM
SIZE: 3” x 2”IMPELLER DIA: 10.25”SPEED: Various
NP
SH
R -
FE
ET
5
10NPSHR - 3570 RPM
0
40
80
120
160
200
240
0 105 15 25 35 45 5520 30 40 50
Model HC-4x25-10
0 20 40 90 100 14012060
00
80
160
240
320
400
480
560
640
720
800
50 100 150 200 250 300 350 400 450 500 550 600
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S 3580 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
2300 RPM
SIZE: 4” x 2.5”IMPELLER DIA: 10”SPEED: 3580 RPM
NP
SH
R -
FE
ET
15
0
30
0
40
80
120
160
200
240
NPSHR - 3580 RPM
4956
6266
6970
6966
62
60 HP50 HP
40 HP
30 HP25 HP20 HP
15 HP
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps-Bearing Frame
Mi8354
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
00
80
160
240
320
400
480
560
640
720
800
100 200 300 400 500 600 700 800 900
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 4” x 3”IMPELLER DIA: 10”SPEED: 3570 RPM
NP
SH
R -
FE
ET
10
20
0
40
80
120
160
200
240
0 20 40 90 100 140 160 180 20012060
NPSHR - 3570 RPM
55 6166
7072
72
70
66
61
55
75 HP
60 HP
50 HP40 HP
30 HP
25 HP20 HP
3570 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
Model HC-4x3-10
00
80
160
240
320
400
480
560
640
720
800
100 200 300 400 500 600 700 800 900 1000 1100
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S 3550 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
2400 RPM
SIZE: 6” x 4”IMPELLER DIA: 10”SPEED: 3550 RPM
NP
SH
R -
FE
ET
15
30
0
40
80
120
160
200
240
0 20 40 90 100 140 160 180 200 220 24012060
NPSHR - 3550 RPM
75 HP
60 HP50 HP
40 HP
30 HP25 HP
52 6169
7578
79
7978
75
69
20 HP
Model HC-6x4-10
Centrifugal Pumps
00
15
30
45
60
75
90
105
120
135
150
400 800 1,200 1,600 2000
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 8” x 6”IMPELLER DIA: 10.25”SPEED: 1780 RPM
NP
SH
R -
FE
ET
0
20
40
0
5
10
15
20
25
30
NPSHR - 1780 RPM
50
1780 RPM
1700 RPM
1600 RPM
1500 RPM
1400 RPM
56
25 HP
100 150 200 250 300 350 400 450
20 HP
15 HP
65 73
78
7340 HP
82
30 HP
84
65
56
78
PAGE: CP-770DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-Bearing Frame
00
10
20
30
40
50
60
70
80
90
100
200 400 600 800 1000 1200 1400 1600 1800 2000
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 8” x 6”IMPELLER DIA: 9.5”SPEED: 1780 RPM
NP
SH
R -
FE
ET
20
40
0
5
10
15
20 1780 RPM
1700 RPM
1600 RPM
1500 RPM
5867
75
81
8586
81
75
67
25 HP
20 HP
15 HP
10 HP
NPSHR - 1780 RPM
50 100 150 200 250 300 350 400
Model HC-8x6-95
Model HC-8x6-10
Mi8332
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
2200 RPM
2000 RPM
1800 RPM
1600 RPM
1400 RPM
1200 RPM
50 6070
7680
80
76
125 HP
100 HP
75 HP
60 HP
50 HP
40 HP
30 HP25 HP
20 HP15 HP10 HP
NPSHR - 1800 RPM
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
NP
SH
R
10
20
0 150 300 450 600 750 900 1050 1200 1350 1500 1650
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380
0
50
100
150
200
250
300
350
0
20
40
60
80
100
SIZE: 6” x 4”IMPELLER DIA: 13.0”SPEED: Various
PAGE: CP-771DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-Bearing Frame
2200 RPM
2000 RPM
1800 RPM
1600 RPM
40 5060 65
70
73
70
65
60
50
75 HP
60 HP50 HP
40 HP
30 HP
25 HP
NPSHR - 1800 RPM
2
4
6
8
10
NP
SH
R -
FE
ET
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0 100 200 300 400 500 600 700 800 900 1000 1100
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
00
50
100
10
20
30
40
50
60
150
200
70
80
90
100
250
300
350110
SIZE: 5” x 3”IMPELLER DIA: 14”SPEED: Various
Model HC-5x3-14
Model HC-6x4-13
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps-Bearing Frame
Mi8352
FLOWRATE U.S. GALLONS PER MINUTES
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
5
10
15
20
NP
SH
R -
FE
ET
SIZE: 6” x 6”IMPELLER DIA: 14”SPEED: Various
2000 RPM
1800 RPM
1600 RPM
1400 RPM
5060
70
30 HP
40 HP
50 HP 60 HP
75 HP
80
83
80
150 HP
125 HP
100 HP
NPSHR - 1760 RPM
0
0 50 100
250 500
150
750 1000
200 250
1250 1500
300 350 400 450
1750 2000
500 550 600 650
2250 2500 27500 0
20
40
60
40
80
120
160
200
80
240
280
Model HC-6x6-14
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
2100 RPM
2000 RPM
1900 RPM
1800 RPM
1700 RPM
1600 RPM
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0 0
25
50
50
100
150
200
75
100
250
300
350
40 50 60 70
8 FT NPSH REQ’D
7580
10 FT 12 FT
17 FT
25 FT85
87
85
80
250 HP
200 HP
150 HP100 HP
SIZE: 8” x 6”IMPELLER DIA: 14”SPEED: Various
Model HC-8x6-14
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-772DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-Bearing Frame
2200 RPM
2000 RPM
1800 RPM
1600 RPM
10
20
30
NP
SH
R -
FE
ET
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0
0
500
125 250
1000
375 500
1500 2000 2500
625 750
3000 3500
875 1000
4000 4500 5000
1125
5500 6000 6500
1250 1375 1500
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
20
40
60
40
80
120
160
80
100
200
240
280
320
SIZE: 10” x 10”IMPELLER DIA: 14”SPEED: Various
5060
70
80
85
80
70
300 HP
250 HP
200 HP
150 HP125 HP
NPSHR - 1800 RPM
Model HC-10x10-14
Mi8353
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
Model Number ExplanationExample: HC4310-SA3P
HC = Horizontal Centrifugal 4 = Suction Size 3 = Discharge Size 10 = Nominal Impeller Dia. SA = SAE Engine Drive 3 = SAE Housing Size P = Shaft Sealing: P=Packing
Features:■ 2” - 10” discharge sizes
■ Capacities to 7000 GPM, 300’ TDH
■ Horsepower: Up to 200 HP
■ Standard ductile iron construction with bronze wear ring and sleeve
■ Replaceable wear rings
■ Superior NPSH characteristics
■ 150# rated fl at faced fl anges
■ Heavy wall construction
■ Grade 5 capscrews
■ HC10 Series- Enclosed impellers, internally hydraulically balanced
■ Double volute on HC10x10-14, for balanced radial forces, HC14 Series- External balance line standard
■ Standard with graphite packing only
■ Flywheel coupling and taper bushings sold separately.
HC SeriesStandard Centrifugal Pumps- SAE Engine Drive
PAGE: CP-775DATE: June 5, 2006
Centrifugal Pumps
HC-3x2-10 3” x 2”Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16030210103 395Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16030210104 395Packing Flanged 1-7/8” x 1/2” 5 8” 2517 16030210105 395
HC-4x25-10 4” x 2.5”Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16042510103 405Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16042510104 405Packing Flanged 1-7/8” x 1/2” 5 8” 2517 16042510105 405
HC-4x3-10 4” x 3”Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16040310103 405Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16040310104 405Packing Flanged 1-7/8” x 1/2” 5 8” 2517 16040310105 405
HC-6x4-10 6” x 4”Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16060410103 465Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16060410104 465Packing Flanged 1-7/8” x 1/2” 5 8” 2517 16060410105 465
HC-8x6-95 8” x 6”Packing Flanged 1-7/8” x 1/2” 1 14” 3535 16080695101 595Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16080695103 595Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16080695104 595
HC-8x6-10 8” x 6”Packing Flanged 1-7/8” x 1/2” 1 14” 3535 16080610101 600Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16080610103 600Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16080610104 600
HC-5x3-14 5” x 3”Packing Flanged 2-1/2” x 5/8” 1 14” 3535 16050314101 590Packing Flanged 2-1/2” x 5/8” 3 11.5” 2517 16050314103 590Packing Flanged 2-1/2” x 5/8” 4 10” 2517 16050314104 590
HC-6x4-13 6” x 4”Packing Flanged 2-1/2” x 5/8” 1 14” 3535 16060413101 595Packing Flanged 2-1/2” x 5/8” 3 11.5” 2517 16060413103 595Packing Flanged 2-1/2” x 5/8” 4 10” 2517 16060413104 595
HC-6x6-14 6” x 6”Packing Flanged 2-1/2” x 5/8” 1 14” 3535 16060614101 700Packing Flanged 2-1/2” x 5/8” 3 11.5” 2517 16060614103 700Packing Flanged 2-1/2” x 5/8” 4 10” 2517 16060614104 700
HC-8x6-14 8” x 6”Packing Flanged 2-1/2” x 5/8” 1 14” 3535 16080614101 805Packing Flanged 2-1/2” x 5/8” 3 11.5” 2517 16080614103 805Packing Flanged 2-1/2” x 5/8” 4 10” 2517 16080614104 805
HC-10x10-14 10” x 10”Packing Flanged 2-1/2” x 5/8” 1 14” 3535 16101014101 1070Packing Flanged 2-1/2” x 5/8” 3 11.5” 2517 16101014103 1070Packing Flanged 2-1/2” x 5/8” 4 10” 2517 16101014104 1070
Mi8333
HC SeriesStandard Centrifugal Pumps- SAE Engine Drive
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Ordering Information10” Nominal Impeller Diameter - (SA) SAE Mount
Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size
Shaft Sealing
Volute Design
Keyed Shaft Dia x Keyway SAE Size Clutch
SizeTaper
BushingOrdering Number
Weight (Lbs.)
14” Nominal Impeller Diameter - (SA) SAE Mount Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size
Shaft Sealing
Volute Design
Keyed Shaft Dia x Keyway SAE Size Clutch
SizeTaper
BushingOrdering Number
Weight (Lbs.)
NOTES: Viton Seals available. Consult price sheets for list price adders. There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders. Flywheel couplings and taper lock bushings are sold separately.
Centrifugal Pumps
PAGE: CP-780DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-SAE Engine Drive
00
80
160
240
320
400
480
560
640
720
800
20 40 60 80 100 120 140 160 180 200 220 240 260
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
3743
4852
5455
5554
52
48
7.5 HP
10 HP 15 HP
20 HP
25 HP30 HP
3570 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
2400 RPM
SIZE: 3” x 2”IMPELLER DIA: 10.25”SPEED: Various
NP
SH
R -
FE
ET
5
10NPSHR - 3570 RPM
0
40
80
120
160
200
240
0 105 15 25 35 45 5520 30 40 50
Model HC-3x2-10
0 20 40 90 100 14012060
00
80
160
240
320
400
480
560
640
720
800
50 100 150 200 250 300 350 400 450 500 550 600
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S 3580 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
2300 RPM
SIZE: 4” x 2.5”IMPELLER DIA: 10”SPEED: 3580 RPM
NP
SH
R -
FE
ET
15
0
30
0
40
80
120
160
200
240
NPSHR - 3580 RPM
4956
6266
6970
6966
62
60 HP50 HP
40 HP
30 HP25 HP20 HP
15 HP
Model HC-4x25-10
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps-SAE Engine Drive
Mi8334
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Model HC-4x3-10
00
80
160
240
320
400
480
560
640
720
800
100 200 300 400 500 600 700 800 900
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 4” x 3”IMPELLER DIA: 10”SPEED: 3570 RPM
NP
SH
R -
FE
ET
10
20
0
40
80
120
160
200
240
0 20 40 90 100 140 160 180 20012060
NPSHR - 3570 RPM
55 6166
7072
72
70
66
61
55
75 HP
60 HP
50 HP40 HP
30 HP
25 HP20 HP
3570 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
00
80
160
240
320
400
480
560
640
720
800
100 200 300 400 500 600 700 800 900 1000 1100
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S 3550 RPM
3400 RPM
3200 RPM
3000 RPM
2800 RPM
2500 RPM
2400 RPM
SIZE: 6” x 4”IMPELLER DIA: 10”SPEED: 3550 RPM
NP
SH
R -
FE
ET
15
30
0
40
80
120
160
200
240
0 20 40 90 100 140 160 180 200 220 24012060
NPSHR - 3550 RPM
75 HP
60 HP50 HP
40 HP
30 HP25 HP
52 6169
7578
79
7978
75
69
20 HP
Model HC-6x4-10
Centrifugal Pumps
PAGE: CP-785DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-SAE Engine Drive
Model HC-8x6-95
00
10
20
30
40
50
60
70
80
90
100
200 400 600 800 1000 1200 1400 1600 1800 2000
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 8” x 6”IMPELLER DIA: 9.5”SPEED: 1780 RPM
NP
SH
R -
FE
ET
20
40
0
5
10
15
20 1780 RPM
1700 RPM
1600 RPM
1500 RPM
5867
75
81
8586
81
75
67
25 HP
20 HP
15 HP
10 HP
NPSHR - 1780 RPM
50 100 150 200 250 300 350 400
Model HC-8x6-10
00
15
30
45
60
75
90
105
120
135
150
400 800 1,200 1,600 2000
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 8” x 6”IMPELLER DIA: 10.25SPEED: 1780 RPM
NP
SH
R -
FE
ET
0
20
40
0
5
10
15
20
25
30
NPSHR - 1780 RPM
50
1780 RPM
1700 RPM
1600 RPM
1500 RPM
1400 RPM
56
25 HP
100 150 200 250 300 350 400 450
20 HP
15 HP
65 73
78
7340 HP
82
30 HP
84
65
56
78
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps-SAE Engine Drive
Mi8335
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
2200 RPM
2000 RPM
1800 RPM
1600 RPM
40 5060 65
70
73
70
65
60
50
75 HP
60 HP50 HP
40 HP
30 HP
25 HP
NPSHR - 1800 RPM
2
4
6
8
10
NP
SH
R -
FE
ET
FLOWRATE U.S. GALLONS PER MINUTE
0 100 200 300 400 500 600 700 800 900 1000 1100
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
00
50
100
10
20
30
40
50
60
150
200
70
80
90
100
250
300
350110
SIZE: 5” x 3”IMPELLER DIA: 14”SPEED: Various
Model HC-5x3-14
2200 RPM
2000 RPM
1800 RPM
1600 RPM
1400 RPM
1200 RPM
50 6070
7680
80
76
125 HP
100 HP
75 HP
60 HP
50 HP
40 HP
30 HP25 HP
20 HP15 HP10 HP
NPSHR - 1800 RPM
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
NP
SH
R
10
20
0 150 300 450 600 750 900 1050 1200 1350 1500 1650
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380
0
50
100
150
200
250
300
350
0
20
40
60
80
100
SIZE: 6” x 4”IMPELLER DIA: 13.0”SPEED: Various
Model HC-6x4-13
Centrifugal Pumps
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
2100 RPM
2000 RPM
1900 RPM
1800 RPM
1700 RPM
1600 RPM
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
0 0
25
50
50
100
150
200
75
100
250
300
350
40 50 60 70
8 FT NPSH REQ’D
7580
10 FT 12 FT
17 FT
25 FT85
87
85
80
250 HP
200 HP
150 HP100 HP
SIZE: 8” x 6”IMPELLER DIA: 14”SPEED: Various
PAGE: CP-790DATE: June 5, 2006
HC SeriesStandard Centrifugal Pumps-SAE Engine Drive
FLOWRATE U.S. GALLONS PER MINUTES
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
5
10
15
20
NP
SH
R -
FE
ET
SIZE: 6” x 6”IMPELLER DIA: 14”SPEED: Various
2000 RPM
1800 RPM
1600 RPM
1400 RPM
5060
70
30 HP
40 HP
50 HP 60 HP
75 HP
80
83
80
150 HP
125 HP
100 HP
NPSHR - 1760 RPM
0
0 50 100
250 500
150
750 1000
200 250
1250 1500
300 350 400 450
1750 2000
500 550 600 650
2250 2500 27500 0
20
40
60
40
80
120
160
200
80
240
280
Model HC-6x6-14
Model HC-8x6-14
Centrifugal Pumps
HC SeriesStandard Centrifugal Pumps-SAE Engine Drive
Mi8336
2200 RPM
2000 RPM
1800 RPM
1600 RPM
10
20
30
NP
SH
R -
FE
ET
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
0
0
500
125 250
1000
375 500
1500 2000 2500
625 750
3000 3500
875 1000
4000 4500 5000
1125
5500 6000 6500
1250 1375 1500
TO
TAL
HE
AD
- M
ET
ER
S
TO
TAL
HE
AD
- F
EE
T
20
40
60
40
80
120
160
80
100
200
240
280
320
SIZE: 10” x 10”IMPELLER DIA: 14”SPEED: Various
5060
70
80
85
80
70
300 HP
250 HP
200 HP
150 HP125 HP
NPSHR - 1800 RPM
Model HC-10x10-14
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
Features:■ Very high torsional fl exibility with a linear torsional defl ection characteristic
■ High torsional vibration and shock load absorbing capability
■ Backlash-free torque transmission
■ Ease of assembly thanks to the plug-in type design with ample axial fl oat
■ Compensation of major misalignments
■ Torque limitation protecting the drive against overload
Flywheel CouplingsStandard Centrifugal Pumps- SAE Engine Drive
PAGE: CP-795DATE: June 5, 2006
Coupling is a highly fl exible fl ywheel design with an axial plug-in facility. It provides a torsionally soft connection between an internal combustion engine and the pump.
The highly fl exible torque transmission characteristic is achieved by a disc-shaped rubber element that is subjected to a torsional load and enables both, the absorption of high torsional vibrations and the compensation of major misalignments.
The inside diameter of the rubber disc element is vulcanized directly to a taper hub. The toothed profi le on the circumference of the element provides in service a virtually backlash-free, positive plug-in connection to the coupling fl ange.
Clutch Size Order Number FE Model Number SAE Bracket SizeCoupling Taper Bushing
required (sold separately)8” 106128101 8” Flywheel Coupling R (SAE 5) 5 251710” 106129101 10” Flywheel Coupling R (SAE 4) 4 2517
11.5” 106130101 11.5” Flywheel Coupling R (SAE 3) 3 251714” 106131101 14” Flywheel Coupling R (SAE 1) 1 3535
Ordering Information
NOTE: Photo includes taper-lock bushing. Bushing is sold separately.
Bore SizeOrder
NumberFE Model Number
Taper-Lock Size
Application
1-7/8” x 1/2” key 106132101 Coupling Bushing 1-7/8” x1/2” 2517 SAE3, SAE4, SAE52-1/2” x 5/8” key 106133101 Coupling Bushing 2-1/2” x5/8” 2517 SAE3, SAE4, SAE51-7/8” x 1/2” key 106134101 Coupling Bushing 1-7/8” x1/2” 3535 SAE12-1/2” x 5/8” key 106135101 Coupling Bushing 2-1/2” x5/8” 3535 SAE1
Ordering Information
Taper-Lock Bushings (sold separately)
2517 Size
3535 Size
Mi8341
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
Flywheel CouplingsStandard Centrifugal Pumps- SAE Engine Drive
PAGE: CP-796DATE: June 5, 2006
Flange
Taper hub with rubber element
Taper bushing
Flywheel coupling type AC-T...F2 is designed to accept a taper bushing for shaft mounting. The rubber disc element is vulcanized directly to the taper hub. After completion of the assembly, a shrink-fi t-like connection, free from backlash in the bore, is established between the coupling hub with rubber disc element and the shaft.
Thanks to the use of commercially available taper bushings with a number of different bore dimensions(sold separately), the need for fi nishing the bores and keyways of the coupling hub is omitted for coupling type AC-T. The torque, which can be transmitted, depends on the particular taper bushing. The advantage is the ease of assembly and disassembly with no need for special tools.
Type AC-T with taper bushing
Mounting instructions for fl ywheel couplingsType AC-T...F2 with taper bushing1. The outer taper of the taper bushing and the bore with the inner taper of the
element hub shall show bright metal and must be free of grease prior to mounting. Preservatives must be removed completely.
2. Insert the taper bushing into the element hub and line up all connecting bores. Make sure that half threaded bores coincide with half plain bores (Fig. 1).
3. Screw in lightly greased or oiled assembly screws. Do not tighten the screws yet (Fig. 2).
4. Slide the element hub with inserted taper bushing onto the cleaned shaft with keyway and put it into the mounting postion Lx (Fig. 3).
5. Tighten the screws uniformly up to the tightening torque MA2 specifi ed in table 2 using a torque wrench.
6. The screws can be retightened again by tapping against the taper bushing with a hammer using an intermediate plate. Repeat, if necessary.
Lx
No. 2517 No. 3535
Fig. 1
Fig. 3
Fig. 2
Centrifugal Pumps
Flywheel CouplingsStandard Centrifugal Pumps- SAE Engine Drive
Mi8351
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Tightening torques for mounting the taper bushing
Coupling Size AC-T2,6 AC-T3 AC-T5
Taper Bushing No. 2517 3535
* UNC Screw Size 1/2 x 13 1/2 x 13
Tightening Torque MA2
Nm 49 115
lb-in 434 1020
Width across fl ats SW 1/4 1/4
Table 1
* No. 2517 Set Screw No. 3535 Cap Screw
How to remove the element hub with taper bushing1. Loosen and remove all screws. Depending on the taper bushing size, screw either 1 or 2
greased screws into the half pulling-off thread(s) of the taper bushing (Fig. 4).
2. Tighten the screws uniformly until the taper bushing is loose in the element hub.
3. As soon as the taper bushing is loose, the element hub can be pulled off the shaft together with the taper bushing.
SW
MA1
Fig. 4
Fig. 5
Tightening torques for fl ywheel couplingsAll bolts and screws must be tightened to the specifi ed torques in order to ensure a reliable torque transmission. Prior to putting the machinery into operation, all bolts and screws of the coupling must be checked for proper fi t.
Detailed mounting instructions are available for the specifi c coupling types.
SAE fl ywheel fl ange 8 10 11-1/2 14
Imperial size bolts 3/8-16 1/2-13
Tightening Torque MA1
Nm 42 102
lb in 372 903
Table 2
MA1
Tightening torques for the bolted fl ange connection to the engine fl ywheel.
Fig. 6
Centrifugal Pumps
PAGE: CP-1100DATE: June 5, 2006
A SeriesNon-Corrosive Centrifugal Pumps
Mi8337
BEST EFFICIENCY RANGE
S45A
S4A
S35A
S3AS2A
200
1
2 4 6 8 10
2
40 60 80
3 4 5
12 14 16 18
100
6 7 8
120
20 22 24 26 28 30 32 34 36 38 40 42
140 160
9 10 11
180 200
12 13
44 46
GPM
LPS
M3PH
105
5
20
10
10
30
40
50
60
70
15
20
25
30
15
20
ME
TE
RS
PS
I
FE
ET
"A" SERIES THERMOPLASTIC CENTRIFUGAL PUMPS
SeriesSuction x Discharge
Model HP VoltagePump Unit
Order No. Wt.
A 2" x 2" MNPT
S2A 2 115/230 94216151 27
S3A 3 230 94216191 29
S35A 3-1/2 230 94216201 31S4A 4 230 94216301 35S45A 4-1/2 230 94216401 39
Fittings kit contains (2) 2" slip x threaded connection union halves 31150109 2
Note: Set of union halves must be purchased separately.
Flooded suction centrifugal pump suitable for use with saltwater, chemical transfer, and other pumping applications that deal with corrosive substances.
Features:■ High tech, non-corrosive plastic construction. All metal
components that have contact with liquid are stainless steel.
■ Motor shaft is completely insulated from any contact with pumping liquid.
■ 2” union connections ensure easy service and optimum water fl ow. Unions must be ordered separately.
■ Discharge port easily rotates to 90 degree increments without removing motor.
■ Lightweight design.
Ordering Information
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-1105DATE: June 5, 2006
S SeriesNon-Corrosive Centrifugal Pumps
Mi8338
This fl ooded suction centrifugal pump is suitable for use with saltwater, chemical transfer (please consult factory for specifi c chemical compatibility), and other pumping applications that deal with corrosive substances.
Features:■ High tech, non-corrosive plastic construction. All metal
components that have contact with liquid are stainless steel.
■ Motor shaft is completely insulated from any contact with pumping liquid.
■ Mechanical seal has ceramic and carbon faces. All other parts are buna-n-rubber and stainless steel.
■ Patented air cooled heat sink allows pump to run dry or in loss-of-prime conditions without damage to the shaft seal. Unconditional two year warranty against seal failure.
■ Floating eye seal on the impeller maximizes pump effi ciency for best fl ow and pressure.
■ Will accept either a standard 1-1/2” union or a male 1-1/2” pipe thread. Unions must be ordered separately.
■ UL and CSA agency listing do not apply to any application other than water applications.
Ordering Information"S" SERIES THERMOPLASTIC CENTRIFUGAL PUMPS
Series Suction x Discharge Model HP VoltagePump Unit
Order No. Wt.
S 1-1/2” x 1-1/2” MNPT
S7KM 3/4 115 94028263 22S1KM 1 115 94028271 24S15KM 1-1/2 115 94028289 26
S2M 2 115/230 94028297 35Fittings kit contains (2) 1-1/2” slip x threaded connection union halves 31175608 1
Note: Set of union halves must be purchased separately.
S2KM
S15KMS1KM
S7KM
0 10 20 30 40 50 60 70 80 90
CAPACITY - GALLONS PER MINUTE
7030
60
5020
40
30
1020
10
PS
I
TO
TAL
HE
AD
- F
EE
T
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-1110DATE: June 5, 2006
JCM SeriesSelf-Draining Non-Corrosive Centrifugal Pumps
Features:■ 100% self-draining case satisfi es both UL and IAPMO
standards.
■ Air-cooled heat sink allows pump to run dry without damage to the shaft seal.
■ Floating eye seal between the closed impeller and the pump case maximizes pump effi ciency for best fl ow and pressure.
■ Accepts a 1-1/2” standard union. Union adapter kits must be ordered separately.
■ UL and CSA Agency listings do not apply to any application other than water applications.
Dimensions (In Inches)
4”
6-1/4”
3”
A
8-7/8”
5-3/4”
1-3/
4”
7-1/
2”
S2JCMS15JCM
S1JCMS7JCM
0 10
.5
1 2 3 4
1 1.5
5
20 30
2
6 7 8 9 10
2.5 3
11 12 13
3.5
40 50 60
4
70
4.5 5
14 15 16 17 18 19
80 90GPM
LPS
M3PH
105
5
10
20
1015
30
40
20
1550
25
60
ME
TE
RS
PS
I
FE
ET
HP A3/4 16-5/8”1 16-5/8”
1-1/2 17-1/16”2 17-1/16”
Centrifugal Pumps
JCM SeriesSelf-Draining Non-Corrosive Centrifugal Pumps
Mi8339
Ordering InformationJCM Series with Straight Union Fit - Single Speed
Model No. Order No. HP Voltage Full Load Amps Svc. Factor WeightS7JCM 94215696 3/4 115 9.8 1 22
S1JCM 94215704 1 115 9.8 1 24
S15JCM 94216587 1-1/2 115 12.4 1 26
S2JCM 94215522 2 115/230 16.8 1 35
JCM Series with Straight Union Fit - Single Speed with Built-In Air Switch & 3’ Cord with Standard 3 Prong PlugModel No. Order No. HP Voltage Full Load Amps Svc. Factor Weight
S7JCM-A3 94216405 3/4 115 10.5 1 22
S1JCM-A3 94216421 1 115 10.5 1 24
S15JCM-A3 94216603 1-1/2 115 12.4 1 26
S2JCM-A3 94216447 2 115/230 16.0 1 35
Straight Union - Must be ordered separatelyModel No. Order No.
(2) S15UNS Halves 31175608
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
REPLACEMENT MOTORS FOR JET & SMALL CENTRIFUGAL PUMPS
Pump Series Frame HPSINGLE PHASE THREE PHASE
Voltage Order No. Wt. Voltage Order No. Wt.
RM2RP2
HJM1 H4D
56C Keyed Shaft
1/2 115/230 90102294R 18 208-230/460 90102419R 193/4 115/230 90102302R 25 208-230/460 90102427R 271 115/230 90102310R 29 208-230/460 90102435R 29
1-1/2 115/230 90102328R 30 208-230/460 90102443R 302 115/230 90102336R 33 208-230/460 90102450R 333 230 90112897R 40 208-230/460 90110628R 68
H4D
56C Keyed Shaft
1/2
Not Available in Single Phase
575 90109372R 193/4 575 90109380R 271 575 90109398R 29
1-1/2 575 90109406R 302 575 90109414R 333 575 90179961R 68
VB6
56C Keyed Shaft
1-1/2 115/230 90118910R 31 208-230/460 90118977R 302 115/230 90118928R 34 208-230/460 90118985R 353 230 90119181R 41 208-230/460 90119207R 69
TCK. Shaft
5 230 90119199R 35 208-230/460 90119215R 587-1/2 230 Not Available 208-230/460 90119017R 74
CPRM3 HJM2
56J Threaded Shaft
1/3 115/230 90177817R 17
Not Available in Three Phase
1/2 115/230 90100637R 183/4 115/230 90100561R 251 115/230 90100579R 29
1-1/2 115/230 90100587R 302 115/230 90119116R 34
SHJM2 56J Threaded Shaft
1 115/230 90100629R 25
Not Available in Three Phase1-1/2 115/230 90100603R 30
2 115/230 90100611R 332-1/2 115/230 90100645R 34
DDD 56Z Square Flange
1/2 115/230 90106246R 18 208-230/460 90106758R 93/4 115/230 90106253R 25 208-230/460 90106766R 101 115/230 90106261R 29 208-230/460 90106774R 12
1-1/2 115/230 90106279R 30 208-230/460 90106782R 142 115/230 90106287R 33 208-230/460 90106790R 17
2-1/2 115/230 90106295R 35 Not Available in Three Phase
RP3 SDEEP
56Z Square Flange
1/2 115/230 90101106R 18Not Available in Three Phase3/4 115/230 90103227R 25
1 115/230 90103235R 29
Cyclone Typhoon
56Z Square Flange
1/2 115/230 90101315R 18
Not Available in Three Phase3/4 115/230 90101327R 251 115/230 90101331R 29
1-1/2 115/230 90101345R 302 115/230 90101352R 33
PAGE: CP-1200DATE: June 5, 2006
Replacement MotorsJM Frame Centrifugal
1. 56C round fl ange motors have 5/8” diameter shaft with 3/16” x 3/16” keyway. 2. 56J round fl ange motors have 5/8” diameter shaft with 7/16-20 UNF-2A thread. 3. 56Z square fl ange motors have a 5/8” diameter shaft with a 1/2-20 UNC-2A thread.
Notes:
Centrifugal Pumps
Replacement MotorsJM Frame Centrifugal
Mi8340
1. Single phase motors are A.O. Smith. 2. Three phase motors are Emerson.
Notes:
JM FRAME REPLACEMENT MOTORS - 3500 R.P.M. - O.D.P.
Pump Series
SINGLE PHASE
HP Frame Size Voltage Order No. Wt.
DB1 DB1-1/2DC1-1/2
DB2DB3DC4
5 184JM 230 90111725R 287-1/2 184JM 230 90119173R 1197-1/2 213JM 230 90111881R 119
10 215JM 230 90113481R 139THREE PHASE
HP Frame Size Voltage Order No. Wt.5 182JM 208-230/460 90118399R 70
7-1/2 184JM 208-230/460 90118407R 7510 213JM 208-230/460 90118415R 11015 215JM 208-230/460 90118423R 14020 254JM 208-230/460 90118431R 15525 256JM 208-230/460 90118837R 19530 284JM 208-230/460 90118845R 23040 286JM 208-230/460 90118852R 32050 324JM 230/460 90118860R 400
THREE PHASE - 575 VOLTHP Frame Size Voltage Order No. Wt.5 182JM 575 90179250R 70
7-1/2 184JM 575 90179276R 7510 213JM 575 90178096R 11015 215JM 575 90178112R 14020 254JM 575 90177981R 15525 256JM 575 C.F. 19530 284JM 575 C.F. 23040 286JM 575 C.F. 32050 324JM 575 C.F. 400
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Centrifugal Pumps
PAGE: CP-1205DATE: Feb 5, 2007
Replacement MotorsHC-Series - ODP
ODP Close Coupled 2-pole Baldor Motors 3-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
106023002 3 208-230/460 Custom 42 9-8.4/4.2 1.15 37F810S093H2 213JP 8.5 10-3001-801
106023003 5 208-230/460 Custom 59 15-14/7 1.15 37F810Y445H2 213JP 8.5 10-3001-801
106023004 7.5 208-230/460 Custom 75 25.7-20.4/10.2 1.15 37F810T320H2 213JP 8.5 10-3001-801
106023005 10 208-230/460 JPM3312T 109 31-28.8/14.4 1.15 Standard 213JP 8.5 10-3001-801
106023006 15 230/460 JPM3314T 128 43.7-41.1/20.7 1.15 Standard 215JP 8.5 10-3001-801
106023007 20 230/460 JPM2514T 167 55.2/27.6 1.15 Standard 254JP 8.5 10-3001-801
106023008 25 230/460 JPM2516T 242 69/34.5 1.15 Standard 256JP 8.5 10-3001-801
106023009 30 230/460 JPM2534T 261 80.5/40.3 1.15 Standard 284JP 12.5 10-3003-801
106023010 40 230/460 JPM2538T 320 103.5/51.8 1.15 Standard 286JP 12.5 10-3003-801
106023011 50 230/460 JPM2542T 386 135.7/67.9 1.15 Standard 324JP 12.5 10-3003-801
106023012 60 230/460 Custom 389 157.4/78.7 1.15 40H026W936G1 326JP 12.5 10-3003-801
106023013 75 230/460 Custom 472 193.6/96.8 1.15 42J060W409G1 364TCZ 12.5 10-3003-801
106023014 100 230/460 Custom 561 262/131 1.15 42J060W642H2 365TCZ 12.5 10-3003-801
106023015 125 460 Custom 782 161.5 1.15 44F024W121H2 404TCZ 12.5 10-3003-801
ODP Close Coupled 4-pole Baldor Motors 3-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
106024001 2 208-230/460 Custom 45 7-6.8/3.4 1.15 37F810W939H2 213JP 8.5 10-3001-801
106024002 3 208-230/460 Custom 64 9.4-8.5/4.25 1.15 37F810X851H2 213JP 8.5 10-3001-801
106024003 5 208-230/460 Custom 74 18.0-15.8/7.9 1.15 37F810X087G1 213JP 8.5 10-3001-801
106024004 7.5 208-230/460 JPM3311T 110 26.45-25.3/12.7 1.15 Standard 213JP 8.5 10-3001-801
106024005 10 208-230/460 JPM3313T 132 32.4-29.9-15 1.15 Standard 215JP 8.5 10-3001-801
106024006 15 230/460 JPM2513T 171 47.2-43.7/21.9 1.15 Standard 254JP 8.5 10-3001-801
106024007 20 230/460 JPM2515T 227 61/30.5 1.15 Standard 256JP 8.5 10-3001-801
106024008 25 230/460 JPM2531T 252 74.8/37.4 1.15 Standard 284JP 12.5 10-3003-801
106024009 30 230/460 JPM2535T 249 82.8/41.4 1.15 Standard 286JP 12.5 10-3003-801
106024010 40 230/460 JPM2539T 372 117.3/58.7 1.15 Standard 324JP 12.5 10-3003-801
106024018 40 230/460 Custom *LS 372 108.2/54.1 1.15 40L045W275G1 324TCZ 12.5 10-3004-801
106024011 50 230/460 JPM2543T 378 140.3/70.2 1.15 Standard 326JP 12.5 10-3003-801
106024019 50 230/460 Custom *LS 378 138.4/69.2 1.15 40L045W917G1 326TCZ 12.5 10-3004-801
106024012 60 230/460 Custom 478 164.8/82.4 1.15 42H078W390G1 364TCZ 12.5 10-3003-801
106024020 60 460 Custom *LS 478 82.4 1.15 42J026W616G1 364TCZ 12.5 10-3004-801
106024013 75 460 Custom 540 101 1.15 42J026W724G1 365TCZ 12.5 10-3004-801
106024014 100 230/460 Custom 822 272/136 1.15 44E089W116H2 404TCZ 12.5 10-3004-801
106024015 125 460 Custom 1012 167 1.15 44E089W110H2 405TCZ 12.5 10-3004-801
106024016 150 460 Custom 1327 199 1.15 18E110X781G1 444TCZ 16 10-3009-801
106024017 200 460 Custom 1421 262 1.15 18E110X335H2 445TCZ 16 10-3009-801
* LS-Special Shaft, used on HC 6x6-14 Series only.
Centrifugal Pumps
Replacement MotorsHC-Series - ODP
Mi8342
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
ODP Close Coupled 6-pole Baldor Motors 3-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
106025003 5 208-230/460 Custom 120 17.9-17.8/8.9 1.15 37G539Y833H3 213JP 8.5 10-3001-801
106025004 7.5 208-230/460 Custom 162 25.5-24.2/8.9 1.15 37F383T374H2 254JP 8.5 10-3001-801
106025005 10 230/460 Custom 228 33.4/16.7 1.15 39K061X458G1 256JP 8.5 10-3001-801
106025007 20 230/460 Custom 377 65/32.5 1.15 39P023W952G3 286JP 12.5 10-3004-801
106025008 25 208-230/460 Custom 374 79.8-74.2/37.1 1.15 40H026X115G1 324JP 12.5 10-3004-801
106025009 30 208-230/460 Custom 367 95.7-88.6/44.3 1.15 40H026X116G1 326JP 12.5 10-3004-801
106025010 40 230/460 Custom 567 112/56 1.15 42H078W641H2 364JP 12.5 10-3004-801
106025011 50 230/460 Custom 610 142.8/71.4 1.15 42H078W366H2 365JP 12.5 10-3004-801
106025012 60 230/460 Custom 830 169/84.5 1.15 44E130W109H2 404JP 12.5 10-3004-801
ODP Close Coupled 2-pole Baldor Motors 1-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
106026002 3 230 Custom 89 18 1.15 37S037S134G1 213JP 8.5 10-3001-801
106026003 5 230 Custom 117 25 1.15 37S037X085G1 213JP 8.5 10-3001-801
106026004 7.5 230 JPL1509T 118 42.6 1.15 Standard 213JP 8.5 10-3001-801
106026005 10 230 JPL1510T 145 52.9 1.15 Standard 215JP 8.5 10-3001-801
ODP Close Coupled 4-pole Baldor Motors 1-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
106026103 5 230 JPL1508T 124 31.1 1.15 Standard 213JP 8.5 10-3001-801
106026104 7.5 230 JPL1510T 140 35.7 1.15 Standard 215JP 8.5 10-3001-801
Centrifugal Pumps
PAGE: CP-1206DATE: Feb 5, 2007
Replacement MotorsHC-Series - TEFC
TEFC Close Coupled 2-pole Baldor Motors 3-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
107023002 3 208-230/460 Custom 94 9-8.4/4.2 1.15 37L079S093G1 213JP 8.5 10-3001-801
107023003 5 208-230/460 Custom 106 15.5-14.6/7.3 1.15 37L079Y445G1 213JP 8.5 10-3001-801
107023004 7.5 208-230/460 JPM3709T 110 23.5-21/10.5 1.15 Standard 213JP 8.5 10-3001-801
107023005 10 208-230/460 JPM3711T 133 29.8-27.2/13.6 1.15 Standard 215JP 8.5 10-3001-801
107023006 15 230/460 JPM2394T 223 42.3-39/19.5 1.15 Standard 254JP 8.5 10-3001-801
107023007 20 230/460 JPM4106T 182 57-52.4/26.2 1.15 Standard 256JP 8.5 10-3001-801
107023008 25 230/460 JPM4107T 373 65.4/32.7 1.15 Standard 284JP 12.5 10-3001-801
107023009 30 230/460 JPM4108T 303 78.4/39.2 1.15 Standard 286JP 12.5 10-3003-801
107023010 40 230/460 JPM4109T 535 105.6/52.8 1.15 Standard 324JP 12.5 10-3003-801
107023011 50 230/460 JPM4114T 550 128.2/64.1 1.15 Standard 326JP 12.5 10-3003-801
107023012 60 230/460 Custom 587 151.4/75.7 1.15 12E975X612H2 364TCZ 12.5 10-3003-801
107023013 75 230/460 Custom 847 188.8/94.4 1.15 14E541X465G1 365TCZ 12.5 10-3003-801
107023014 100 230/460 Custom 847 248.4/124.2 1.15 14E724X840H2 405TCZ 12.5 10-3003-801
107023015 125 460 Custom 1350 158 1.15 18E789Y166H2 444TCZ 12.5 10-3003-801
TEFC Close Coupled 4-pole Baldor Motors 3-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
107024001 2 208-230/460 Custom 90 10.9-9.9/4.9 1.15 37L079S093G1 213JP 8.5 10-3001-801
107024002 3 208-230/460 Custom 99 9.8/4.9 1.15 37J247Y002G1 213JP 8.5 10-3001-801
107024003 5 208-230/460 Custom 108 18-15.8/7.9 1.15 37L079X088G1 213JP 8.5 10-3001-801
107024004 7.5 208-230/460 JPM3710T 127 25.9-23.9/12 1.15 Standard 213JP 8.5 10-3001-801
107024005 10 208-230/460 JPM3714T 145 31.6-24.4/14.7 1.15 Standard 215JP 8.5 10-3001-801
107024006 15 230/460 JPM2333T 236 47.2-43.5/21.7 1.15 Standard 254JP 8.5 10-3001-801
107024007 20 230/460 JPM2334T 283 57.5/28.8 1.15 Standard 256JP 8.5 10-3001-801
107024008 25 230/460 JPM4103T 380 69/34.5 1.15 Standard 284JP 12.5 10-3003-801
107024009 30 230/460 JPM4104T 403 82.8/41.4 1.15 Standard 286JP 12.5 10-3003-801
107024010 40 230/460 JPM4110T 564 108.1/53.6 1.15 Standard 324JP 12.5 10-3003-801
107024018 40 230/460 Custom *LS 554 108.2/54.1 1.15 12E976X276H2 324TCZ 12.5 10-3004-801
107024011 50 230/460 JPM4115T 563 138/69 1.15 Standard 326JP 12.5 10-3003-801
107024019 50 230/460 Custom *LS 575 136/68 1.15 12E976X270H2 326TCZ 12.5 10-3004-801
107024012 60 230/460 Custom 578 161.6/80.9 1.15 14E541X279G1 364TCZ 12.5 10-3003-801
107024020 60 460 Custom *LS 700 78 1.15 12E978X667H2 364TCZ 12.5 10-3004-801
107024013 75 460 Custom 808 98 1.15 14E481X101G1 365TCZ 12.5 10-3004-801
107024014 100 230/460 Custom 889 130 1.15 14E542X644G1 404TCZ 12.5 10-3004-801
107024015 125 460 Custom 1327 162 1.15 18E790X455H2 444TCZ 12.5 10-3004-801
107024016 150 460 Custom 1529 194 1.15 18E788X590H2 445TCZ 16 10-3009-801
107024017 200 460 Custom 1859 259 1.15 18E788X669H2 445TCZ 16 10-3009-801
* LS-Special Shaft, used on HC 6x6-14 Series only.
Centrifugal Pumps
Replacement MotorsHC-Series - TEFC
Mi8378
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
TEFC Close Coupled 6-pole Baldor Motors 3-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
107025003 5 208-230/460 Custom 131 17.9-17.8/8.9 1.15 37L079Y833H2 215JP 8.5 10-3001-801
107025004 7.5 208-230/460 Custom 178 25.4/12.7 1.15 07H301W353 254JP 8.5 10-3001-801
107025005 10 230/460 Custom 290 32.6/16.3 1.15 09P028X829G4 256JP 8.5 10-3001-801
107025007 20 230/460 Custom 372 61.2/30.6 1.15 10M021X911G1 286JP 12.5 10-3004-801
107025008 25 208-230/460 Custom 429 76.8/38.4 1.15 12H062W298 324JP 12.5 10-3004-801
107025009 30 208-230/460 Custom 571 84/42 1.15 12H62W103 326JP 12.5 10-3004-801
107025010 40 230/460 Custom 785 111.6/55.8 1.15 14E227X378H2 364TCZ 12.5 10-3004-801
107025011 50 230/460 Custom 769 139.2/69.6 1.15 14E227W769H2 365TCZ 12.5 10-3004-801
107025012 60 230/460 Custom 1114 160.4/80.2 1.15 16E213W750H2 404TCZ 12.5 10-3004-801
TEFC Close Coupled 2-pole Baldor Motors 1-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
107026002 3 230 Custom 97 34.4/17.2 1.15 37M059X090G1 213JP 8.5 10-3001-801
107026003 5 230 Custom 127 25 1.15 37M059X085G1 213JP 8.5 10-3001-801
107026004 7.5 230 Custom 126 35.9 1.15 37M059W579G1 213JP 8.5 10-3001-801
107026005 10 230 Custom 147 46 1.15 37G461W578G3 215JP 8.5 10-3001-801
TEFC Close Coupled 4-pole Baldor Motors 1-Phase (Standard Effi ciency)
FE Part Number HP Voltage Description Wt. Service Factor Amps
Service Factor Baldor Spec # Frame
Size AK Dim Shaft DWG
107026103 5 230 Custom 110 24 1.15 37G461T877G1 213JP 8.5 10-3001-801
107026104 7.5 230 Custom 115 33.5 1.15 37G461T876G1 215JP 8.5 10-3001-801
Centrifugal Pumps
PAGE: CP-1210DATE: June 5, 2006
Replacement MotorsHC-Series
Shaft 10-3003-801
Shaft 10-3001-801
+.0
00-.
005
ø8.
500
.25
4-1/2 UNC TAP ON 7.25 BOLT CIRCLE STRADDLE CENTERLINE
63
1.75
0ø
1.74
8
2.375
5.875
63 63
8.125
2.50KEYWAY
R.030R.030
1/2 UNC-2B TAP1.5 DEEP
1.37
50ø
1.37
45
.03 x 45o
.03 x 45o
A.001.005
A
1.24
95ø
1.24
90
.250
.245
+.000-.0151.112
+.0
00-.
005
ø12
.500
.25
4-5/8 UNC TAP ON 11.0 BOLT CIRCLE STRADDLE CENTERLINE
63
1.75
0ø
1.74
8
2.375
5.875
63 63
8.125
2.50KEYWAY
R.030R.030
1/2 UNC-2B TAP1.5 DEEP
1.37
50ø
1.37
45
.03 x 45o
.03 x 45o
A.001.005
A
1.24
95ø
1.24
90
.250
.245
+.000-.0151.112
Centrifugal Pumps
Replacement MotorsHC-Series
Mi8343
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
.25
+.0
00-.
005
63
ø12
.500
+.0
032
-.00
00ø
2.50
25
ø2.
302
NOTE: Blend 45o TO R .09.030 x 45o
45 o
5.44
8.70R
.09
633.06
KEYWAY
63A
3/4-10 UNC-2B x 1.63FULL THREAD DEPTH
2.24
96Ø
2.24
91
+.0
02-.
000
ø.5
00
+.000-.015ø1.972
A.001.005
.25
+.0
00-.
005
63
ø16
.000
+.0
032
-.00
00ø
2.50
25
ø2.
302
NOTE: Blend 45o TO R .09.030 x 45o
45 o
5.44
8.70
R.09
633.06
KEYWAY
63A
3/4-10 UNC-2B x 1.63FULL THREAD DEPTH
2.24
96Ø
2.24
91
+.0
02-.
000
ø.5
00
+.000-.015ø1.972
A.001.005
Shaft 10-3009-801
Shaft 10-3004-801
Centrifugal Pumps
PAGE: CP-1300DATE: Feb 5, 2007
Close Coupled Dimensional Drawings7.5” Diameter Series
RO
TATI
ON
WA
RN
ING
CP
DA
CY
BFB
A
XD
D1
AB
EE
A
HØ
Z D
DD3 DD2
Mod
elHP
RPM
Suct
ion
Disc
h.Fr
ame
AB
CD
EF
HCP
XY
ZDD
1DD
2DD
3AB
BADA
HC
3X
15-7
5
33
60
03
1.5
213*
9.5
812
.81
5.25
4.25
5.5
0.41
23.5
62.
894.
38
4.9
44.
816.
88
6.75
4.5
9.19
53
60
03
1.5
213*
9.5
812
.81
5.25
4.25
5.5
0.41
23.5
62.
894.
38
4.9
44.
816.
88
6.75
4.5
9.19
7.5
36
00
31.
521
3*9.
58
12.8
15.
254.
255.
50.
4123
.56
2.89
4.3
84.
94
4.81
6.8
86.
754.
59.
1910
36
00
31.
521
3JP
9.5
812
.81
5.25
4.25
5.5
0.41
23.5
62.
894.
38
4.9
44.
816.
88
7.46
4.5
10.0
3
HC
3X
2-75
33
60
03
221
3*9.
58
12.8
15.
254.
255.
50.
4123
.56.
252.
754.
55.
06
4.81
7.5
6.75
4.5
9.19
53
60
03
221
3*9.
58
12.8
15.
254.
255.
50.
4123
.56.
252.
754.
55.
06
4.81
7.5
6.75
4.5
9.19
7.5
36
00
32
213*
9.5
812
.81
5.25
4.25
5.5
0.41
23.5
6.25
2.75
4.5
5.0
64.
817.
56.
754.
59.
1910
36
00
32
213
JP9.
58
12.8
15.
254.
255.
50.
4123
.56.
252.
754.
55.
06
4.81
7.5
7.46
4.5
10.0
315
36
00
32
213
JP9.
58
15.5
65.
254.
257
0.41
26.2
56.
252.
754.
55.
06
4.81
7.5
7.46
4.5
10.0
3
HC
4X
25-7
5
7.5
36
00
42.
521
3*9.
58
12.8
15.
254.
255.
50.
4123
.78
6.5
34.
755.
63
5.19
8.25
6.75
4.5
9.19
103
60
04
2.5
213
JP9.
58
12.8
15.
254.
255.
50.
4123
.78
6.5
34.
755.
63
5.19
8.25
7.46
4.5
10.0
315
36
00
42.
521
5JP
9.5
815
.56
5.25
4.25
70.
4126
.53
6.5
34.
755.
63
5.19
8.25
7.46
4.5
10.0
320
36
00
42.
525
4JP
11.2
59.
517
.93
6.25
58.
250.
53
28.9
6.5
34.
755.
63
5.19
8.25
8.93
512
253
60
04
2.5
256
JP11
.25
11.2
517
.93
6.25
510
0.5
328
.96.
53
4.75
5.6
35.
198.
258.
935
12
HC
4X
3-7
5
7.5
36
00
43
213*
9.5
812
.81
6.25
4.25
5.5
0.41
23.8
17
35
5.81
5.31
8.75
6.75
4.5
9.19
103
60
04
321
3JP
9.5
812
.81
6.25
4.25
5.5
0.41
23.8
17
35
5.81
5.31
8.75
7.46
4.5
10.0
315
36
00
43
215
JP9.
58
15.5
66.
254.
257
0.41
26.5
67
35
5.81
5.31
8.75
7.46
4.5
10.0
320
36
00
43
254
JP11
.25
9.5
17.9
36.
255
8.25
0.5
328
.93
73
55.
815.
318.
758.
935
1225
36
00
43
256
JP11
.25
11.2
517
.93
6.25
510
0.5
328
.93
73
55.
815.
318.
758.
935
123
03
60
04
328
4JP
11.2
510
.75
19.8
16.
255
9.5
0.5
33
0.81
73
55.
815.
318.
7512
.21
513
.96
HC
4X
4-7
5
153
60
04
421
5JP
9.5
815
.56
5.25
4.25
70.
4126
.72
83
5.5
6.0
95.
53
107.
464.
510
.03
203
60
04
425
4JP
11.2
59.
517
.93
6.25
58.
250.
53
29.0
98
35.
56.
09
5.5
310
8.93
512
253
60
04
425
6JP
11.2
511
.25
17.9
36.
255
100.
53
29.0
98
35.
56.
09
5.5
310
8.93
512
30
36
00
44
284
JP12
.25
10.7
519
.81
75.
59.
50.
53
30.
978
35.
56.
09
5.5
310
12.2
15
13.9
64
03
60
04
428
6JP
12.2
512
.25
19.8
17
5.5
110.
53
30.
978
35.
56.
09
5.5
310
12.2
15
13.9
650
36
00
44
324
JP14
.25
13.7
521
.19
86.
2510
.50.
66
32.3
58
35.
56.
09
5.5
310
12.2
15.
514
.59
HC
5X
4-7
5
253
60
05
425
6JP
11.2
511
.25
17.9
36.
255
100.
53
29.5
28
35.
56.
55.
9110
8.93
512
30
36
00
54
284
JP12
.25
10.7
519
.81
75.
59.
50.
53
31.4
83.
255.
56.
55.
9110
12.2
15
13.9
64
03
60
05
428
6JP
12.2
512
.25
19.8
17
5.5
110.
53
31.4
83.
255.
56.
55.
9110
12.2
15
13.9
650
36
00
54
324
JP15
.25
13.7
521
.19
86.
2510
.50.
66
32.7
88
3.25
5.5
6.5
5.91
1012
.21
5.5
14.5
96
03
60
05
432
6*14
.25
13.7
521
.19
86.
2512
0.6
632
.78
83.
255.
56.
55.
9110
13.2
25.
515
.59
Mi8370 No
te:
Dim
ensi
ons
are
for
estim
atin
g pu
rpos
es o
nly.
Cer
tifi e
d di
men
sion
dra
win
gs a
re a
vaila
ble
on r
eque
st.
Centrifugal Pumps
PAGE: CP-1305DATE: Feb 5, 2007
Close Coupled Dimensional Drawings10” Diameter Series
RO
TATI
ON
WA
RN
ING
Z
AB
HØ
EE
A
DD
1X
D
DD3 DD2
DA
CP
CY
F B
BA
Mod
elHP
RPM
Suct
ion
Disc
h.Fr
ame
AB
CD
EF
HCP
XY
ZDD
1DD
2DD
3AB
BADA
HC
3x2
-10
1018
00
32
215
JP9.
58
13.9
45.
254.
257
0.41
24.8
27.
53
5.75
6.3
46.
258.
757.
464.
510
.03
103
60
03
221
3JP
9.5
812
.81
5.25
4.25
70.
4123
.69
7.5
35.
756.
34
6.25
8.75
7.46
4.5
10.0
315
36
00
32
215
JP9.
58
15.5
65.
254.
257
0.41
26.4
47.
53
5.75
6.3
46.
258.
757.
464.
510
.03
203
60
03
225
4JP
11.2
59.
517
.93
6.25
58.
25.0
53
28.8
17.
53
5.75
6.3
46.
258.
758.
935
1225
36
00
32
256
JP11
.25
11.2
517
.93
6.25
510
0.5
328
.81
7.5
35.
756.
34
6.25
8.75
8.93
512
30
36
00
32
284
JP12
.25
12.2
519
.81
75.
59.
50.
53
30.
69
7.5
35.
756.
34
6.25
8.75
12.2
15
13.9
6
HC
4x2
5-1
0
218
00
42.
521
3*9.
58
12.8
19.
254.
255.
50.
4123
.81
83.
037
6.78
6.47
9.5
6.75
4.5
9.19
318
00
42.
521
3*9.
58
12.8
15.
254.
255.
50.
4123
.81
83.
037
6.78
6.47
9.5
6.75
4.5
9.19
518
00
42.
521
3*9.
58
12.8
15.
254.
255.
50.
4123
.81
83.
037
6.78
6.47
9.5
6.75
4.5
9.19
7.5
180
04
2.5
213
JP9.
58
13.9
45.
254.
255.
50.
4124
.94
83.
037
6.78
6.47
9.5
6.75
4.5
9.19
153
60
04
2.5
215
JP9.
58
15.5
65.
254.
257
0.41
26.5
68
3.03
76.
786.
479.
57.
464.
510
.03
203
60
04
2.5
254
JP11
.25
9.5
17.9
36.
255
8.25
0.5
328
.93
83.
037
6.78
6.47
9.5
8.93
512
253
60
04
2.5
256
JP11
.25
11.2
517
.93
6.25
510
0.5
328
.93
83.
037
6.78
6.47
9.5
8.93
512
30
36
00
42.
528
4JP
12.2
510
.75
19.8
17
5.5
9.5
0.5
33
0.81
83.
037
6.78
6.47
9.5
12.2
15
13.9
640
360
04
2.5
286
JP12
.25
12.2
519
.81
75.
511
0.53
30.8
18
3.03
76.
786.
479.
512
.21
513
.96
503
60
04
2.5
324
JP14
.25
13.7
521
.19
86.
2510
.50.
66
32.1
98
3.03
76.
786.
479.
512
.21
5.5
14.5
960
360
04
2.5
326*
14.2
513
.75
21.1
98
6.25
120.
6632
.19
83.
037
6.78
6.47
9.5
13.2
25.
515
.59
HC
4x3
-10
30
36
00
43
284
JP12
.25
10.7
519
.81
75.
59.
50.
53
30.
93
8.5
3.0
96.
257.
036.
63
1012
.21
513
.96
40
36
00
43
286
JP12
.25
12.2
519
.81
75.
511
0.5
33
0.93
8.5
3.0
96.
257.
03
6.6
310
12.2
15
13.9
650
36
00
43
324
JP14
.25
13.7
521
.19
86.
2510
.50.
66
32.3
18.
53.
09
6.25
7.03
6.6
310
12.2
15.
514
.59
60
36
00
43
326*
14.2
513
.75
21.1
98
6.25
120.
66
32.3
18.
53.
09
6.25
7.03
6.6
310
13.2
25.
515
.59
753
60
04
33
64*
15.7
514
22.3
19
711
.25
0.6
63
3.4
38.
53.
09
6.25
7.03
6.6
310
13.2
26.
1216
.59
100
36
00
43
36
5*15
.75
1423
.31
97
12.2
50.
66
33.
43
8.5
3.0
96.
257.
036.
63
1013
.22
6.12
16.5
9
HC
6x4
-10
30
36
00
64
284
JP12
.25
10.7
519
.81
75.
59.
50.
53
32.2
29.
54.
256.
57.
38
6.8
411
125
13.9
640
36
00
64
286
JP12
.25
12.2
519
.81
75.
511
0.5
332
.22
9.5
4.25
6.5
7.3
86.
84
1112
.21
513
.96
503
60
06
432
4JP
14.2
513
.75
21.1
98
6.25
10.5
0.6
63
3.6
9.5
4.25
6.5
7.3
86.
84
1112
.21
5.5
14.5
96
03
60
06
432
6*14
.25
13.7
521
.19
86.
2512
0.6
63
3.6
9.5
4.25
6.5
7.3
86.
84
1113
.22
5.5
15.5
975
36
00
64
36
4*15
.75
1422
.31
97
11.2
50.
66
34.
729.
54.
256.
57.
38
6.8
411
13.2
26.
1216
.59
100
36
00
64
36
5*15
.75
1423
.31
97
12.2
50.
66
35.7
29.
54.
256.
57.
38
6.8
411
13.2
26.
1216
.59
125
36
00
64
404*
18.5
16.6
227
.84
108
12.2
50.
8140
.25
9.5
4.25
6.5
7.3
86.
84
1116
.39
6.8
818
.41
HC
8x6
-10
512
00
86
213
JP9.
58
13.9
45.
254.
257
0.41
30.
8210
2.75
8.25
118.
85
13.7
57.
464.
2510
.03
7.5
120
08
625
4JP
11.2
59.
515
.81
6.25
58.
250.
53
32.6
910
2.75
8.25
118.
85
13.7
57.
934.
7511
.03
1012
00
86
256
JP11
.25
11.2
519
.43
6.25
510
0.5
33
6.31
102.
758.
2511
8.8
513
.75
9.49
4.75
1220
180
08
625
6JP
11.2
511
.25
18.3
26.
255
100.
53
35.2
102.
758.
2511
8.8
513
.75
8.93
512
30
180
08
628
6JP
12.2
512
.25
21.3
17
5.5
110.
53
38.
1910
2.75
8.25
118.
85
13.7
512
.21
513
.96
4018
00
86
324
JP14
.25
13.7
521
.19
86.
2510
.50.
53
38.
0710
2.75
8.25
118.
85
13.7
512
.21
5.5
14.5
95
120
08
621
3JP
9.5
813
.94
5.25
4.25
70.
413
0.82
102.
758.
2511
8.8
513
.75
7.46
4.25
10.0
37.
512
00
86
254
JP11
.25
9.5
15.8
16.
255
8.25
0.5
332
.69
102.
758.
2511
8.8
513
.75
7.93
4.75
11.0
3H
C 8
x6-9
515
180
08
625
4JP
11.2
59.
515
.81
6.25
58.
250.
53
32.6
910
2.75
8.25
118.
85
13.7
58.
935
1220
180
08
625
6JP
11.2
511
.25
18.3
26.
255
100.
53
35.2
102.
758.
2511
8.8
513
.75
8.93
512
2518
00
86
284
JP12
.25
10.7
519
.81
75.
59.
50.
53
36.
6910
2.75
8.25
118.
85
13.7
512
.21
513
.96
Mi8371 No
te:
Dim
ensi
ons
are
for
estim
atin
g pu
rpos
es o
nly.
Cer
tifi e
d di
men
sion
dra
win
gs a
re a
vaila
ble
on r
eque
st.
Centrifugal Pumps
PAGE: CP-1310DATE: Feb 5, 2007
Close Coupled Dimensional Drawings14” Diameter Series
RO
TATI
ON
WA
RN
ING
F
DA
B
BA
CP
CY
AB
XD
D1
EE
A
HØ
Z D
DD3 DD2
Mod
elHP
RPM
Suct
ion
Disc
h.Fr
ame
AB
CD
EF
HCP
XY
ZDD
1DD
2DD
3AB
BADA
HC
5x3
-14
2018
00
53
256
JP11
.25
11.2
518
.32
6.25
510
0.5
33
0.51
9.5
4.75
8.5
109.
512
.25
8.93
512
2518
00
53
284
JP12
.25
10.7
519
.81
75.
59.
50.
5332
9.5
4.75
8.5
109.
512
.25
12.2
15
13.9
63
018
00
53
286
JP12
.25
12.2
521
.31
75.
511
0.5
33
3.5
9.5
4.75
8.5
109.
512
.25
12.2
15
13.9
640
180
05
332
4JP
14.2
513
.75
21.1
98
6.25
10.5
0.6
63
3.3
89.
54.
758.
510
9.5
12.2
512
.21
5.5
14.5
9
HC
6x4
-13
30
180
06
428
6JP
12.2
512
.25
21.3
17
5.5
110.
53
34.
99
116
89.
38
8.8
812
.512
.21
513
.96
4018
00
64
324
JP14
.25
13.7
521
.19
86.
2510
.50.
66
34.
8711
68
9.3
88.
88
12.5
12.2
15.
514
.59
5018
00
64
326
JP14
.25
13.7
522
.19
86.
2512
0.6
635
.87
116
89.
38
8.8
812
.512
.21
5.5
15.5
96
018
00
64
36
4*15
.75
1422
.31
97
11.2
50.
66
35.9
911
68
9.3
88.
88
12.5
13.2
6.12
16.5
9
HC
6x6
-14
4018
00
66
324
JP14
.25
13.7
521
.19
86.
2510
.50.
66
34.
94
10.5
5.19
9.5
1211
1512
5.5
14.5
950
180
06
632
6JP
14.2
513
.75
22.1
98
6.25
120.
66
35.9
410
.55.
199.
512
1115
12.2
15.
514
.59
60
180
06
63
64*
15.7
514
22.3
19
711
.25
0.6
63
6.0
610
.55.
199.
512
1115
13.2
6.12
16.5
975
180
06
63
65*
15.7
514
24.3
19
712
.25
0.6
63
8.0
610
.55.
199.
512
1115
13.2
26.
1216
.59
100
180
06
640
4*18
.516
.62
25.8
510
812
.25
0.81
39.6
10.5
5.19
9.5
1211
1516
.39
6.8
818
.41
HC
8x6
-14
2012
00
86
296*
12.2
512
21.3
17
5.5
110.
53
35.7
89.
566.
38
4.81
13.3
712
7.22
12.2
15
103.
96
2512
00
86
324*
14.2
525
21.1
98
6.25
10.5
0.6
635
.66
9.56
6.3
84.
8113
.37
127.
2212
.21
5.5
14.5
93
012
00
86
326*
14.2
513
.75
22.1
98
6.25
120.
66
36.
66
9.56
6.3
84.
8113
.37
127.
2212
.21
5.5
14.5
940
120
08
63
64*
15.7
514
22.3
19
711
.25
0.6
63
6.78
9.56
6.3
84.
8113
.37
127.
2213
.26.
1216
.59
7518
00
86
36
5*15
.75
1424
.31
97
12.2
50.
66
38.
789.
566.
38
4.81
13.3
712
7.22
13.2
26.
1216
.59
100
180
08
640
4*18
.516
.62
25.8
510
812
.25
0.81
40.3
29.
566.
38
4.81
13.3
712
7.22
16.3
96.
88
18.4
112
518
00
86
44
4*22
1727
.111
914
.50.
8141
.57
9.56
6.3
84.
8113
.37
127.
2219
.88
7.75
21.8
815
018
00
86
44
5*22
1931
.38
119
16.5
0.81
45.
85
9.56
6.3
84.
8113
.37
127.
2219
.88
7.75
21.8
8
HC
10x
10-1
4
2512
00
1010
324*
14.2
513
.75
21.1
98
6.25
10.5
0.6
63
6.07
126.
2512
16.2
513
.520
12.2
15.
514
.59
4012
00
1010
36
4*15
.75
1422
.31
97
11.2
50.
66
37.1
912
6.25
1216
.25
13.5
2013
.26.
1216
.59
5012
00
1010
36
5*15
.75
1424
.31
97
12.2
50.
66
39.1
912
6.25
1216
.25
13.5
2013
.22
6.12
16.5
96
012
00
1010
404*
18.5
16.6
225
.85
108
12.2
50.
8140
.73
126.
2512
16.2
513
.520
16.3
96.
88
18.4
110
018
00
1010
404*
18.5
16.6
225
.85
108
12.2
50.
8140
.73
126.
2512
16.2
513
.520
16.3
96.
88
18.4
112
518
00
1010
405T
CZ
2217
27.1
119
14.5
0.81
41.9
812
6.25
1216
.25
13.5
2019
.88
7.75
21.8
815
018
00
1010
44
4TC
Z22
1931
.38
119
16.5
0.81
46.2
612
6.25
1216
.25
13.5
2019
.88
7.75
21.8
820
018
00
1010
44
5TC
Z21
.519
.531
.38
119
16.5
0.81
46.2
612
6.25
1216
.25
13.5
2019
.06
7.5
22.1
8
Mi8372 No
te:
Dim
ensi
ons
are
for
estim
atin
g pu
rpos
es o
nly.
Cer
tifi e
d di
men
sion
dra
win
gs a
re a
vaila
ble
on r
eque
st.
Centrifugal Pumps
PAGE: CP-1315DATE: Feb 5, 2007
Bearing Frame Dimensional DrawingsAll Series (7.5”, 10” & 14” Diameter)
Mod
elFi
gure
Suct
ion
Disc
h.A
BD
EF
GH
LN
QU
XY
ZCP
DD1
DD2
DD3
KEY
HC
3X
15-7
51
31.
513
.25
7.37
57.
00
5.75
5.37
5.7
5.6
875
17.9
65.
628.
00
1.87
56
2.89
4.3
825
.96
4.9
44.
816.
88
.50
HC
3X
2-75
13
213
.25
7.37
57.
00
5.75
5.37
5.7
5.6
875
17.9
65.
628.
00
1.87
56.
252.
754.
525
.96
5.0
64.
817.
5.5
0
HC
4X
25-7
51
42.
513
.25
7.37
57.
00
5.75
5.37
5.7
5.6
875
18.2
45.
628.
00
1.87
56.
53
4.75
26.2
35.
63
5.19
8.25
.50
HC
4X
3-7
51
43
13.2
57.
375
7.0
05.
755.
375
.75
.687
518
.24
5.62
8.0
01.
875
73
526
.23
5.81
5.31
8.75
.50
HC
4X
4-7
51
44
13.2
57.
375
7.0
05.
755.
375
.75
.687
518
.24
5.62
8.0
01.
875
83
5.5
26.2
36.
09
5.5
310
.50
HC
5X
4-7
51
54
13.2
57.
375
7.0
05.
755.
375
.75
.687
518
.49
5.62
8.0
01.
875
83.
255.
526
.48
6.5
5.91
10.5
0
HC
3X
2-10
13
213
.25
7.37
57.
00
5.75
5.37
5.7
5.6
875
18.2
45.
628.
00
1.87
57.
53
5.75
26.2
46.
34
6.25
8.75
.50
HC
4X
25-1
01
42.
513
.25
7.37
57.
00
5.75
5.37
5.7
5.6
875
18.2
75.
628.
00
1.87
58
3.03
726
.26
6.78
6.47
9.5
.50
HC
4X
3-1
01
43
13.2
57.
375
7.0
05.
755.
375
.75
.687
518
.33
5.62
8.0
01.
875
8.5
3.0
96.
2526
.32
7.03
6.6
310
.50
HC
6X
4-1
01
64
13.2
57.
375
7.0
05.
755.
375
.75
.687
519
.49
5.62
8.0
01.
875
9.5
4.25
6.5
27.4
87.
38
6.8
411
.50
HC
8X
6-1
02
86
13.2
57.
375
7.0
05.
755.
375
.75
.687
517
.99
5.62
8.0
01.
875
102.
758.
2532
.14
118.
85
13.7
5.5
0
HC
8X
6-9
52
86
13.2
57.
375
7.0
05.
755.
375
.75
.687
517
.99
5.62
8.0
01.
875
102.
758.
2532
.14
118.
85
13.7
5.5
0
HC
6X
4-1
32
64
13.2
510
.687
57.
00
5.75
8.6
875
.75
.687
521
.24
5.62
8.0
02.
511
68
35.4
99.
38
8.8
812
.5.6
25
HC
5X
3-1
42
53
13.2
510
.687
57.
00
5.75
8.6
875
.75
.687
519
.99
5.62
8.0
02.
59.
54.
758.
53
4.14
109.
512
.25
.625
HC
6X
6-1
42
66
13.2
510
.687
57.
00
5.75
8.6
875
.75
.687
520
.43
5.62
8.0
02.
510
.55.
199.
53
4.58
1211
15.6
25
HC
8X
6-1
42
86
13.2
510
.687
57.
00
5.75
8.6
875
.75
.687
521
.62
5.62
8.0
02.
59.
566.
38
4.81
35.7
713
.37
127.
22.6
25
HC
10X
10-1
42
1010
13.2
510
.687
57.
00
5.75
8.6
875
.75
.687
521
.49
5.62
8.0
02.
512
6.25
1235
.64
16.2
513
.520
.625
KE
Y U
N
Q
F B
L
YE
E
A
XD
D1
DD3 DD2
Z
D
G
HØ
4 H
OLE
S
CP
FIG
UR
E 1
RO
TATI
ON
EE
A
C
G
D
DD2DD3
X
Z
DD
1Y
F B
L
CP
Q
HØ
4 H
OLE
S
N
U
KE
Y
FIG
UR
E 2
Mi8373 No
te:
Dim
ensi
ons
are
for
estim
atin
g pu
rpos
es o
nly.
Cer
tifi e
d di
men
sion
dra
win
gs a
re a
vaila
ble
on r
eque
st.
Centrifugal Pumps
PAGE: CP-1320DATE: Feb 5, 2007
SAE Dimensional DrawingsAll Models (10” & 14” Diameter)
Mod
elFi
gure
Suct
ion
Disc
h.X
YM
PZ
SAE
#B.
C.#
Hole
sSi
zeA
BH
FD
CPE
GKE
YH
C 3
x2-1
01
32
7.5
311
.23
5.75
316
.875
120.
397
17.7
516
.123
0.6
875
10.8
37.
00
23.7
61.
875
11.5
.50
HC
3x2
-10
13
27.
53
11.2
35.
754
1512
0.39
715
.88
14.2
48
0.6
875
11.3
87.
00
24.3
11.
875
11.5
.50
HC
3x2
-10
13
27.
53
11.2
35.
755
13.1
28
0.39
714
12.3
730.
687
510
.83
7.0
023
.76
1.87
511
.5.5
0H
C 4
x25
-10
14
2.5
83.
0311
.26
73
16.8
7512
0.39
717
.75
16.1
230.
687
510
.83
7.0
023
.79
1.87
511
.5.5
0H
C 4
x25
-10
14
2.5
83.
0311
.26
74
1512
0.39
715
.88
14.2
48
0.6
875
11.3
87.
00
24.3
41.
875
11.5
.50
HC
4x2
5-1
01
42.
58
3.03
11.2
67
513
.12
80.
397
1412
.373
0.6
875
10.8
37.
00
23.7
91.
875
11.5
.50
HC
4x3
-10
14
38.
53.
09
11.3
26.
253
16.8
7512
0.39
717
.75
16.1
230.
687
510
.83
7.0
023
.85
1.87
511
.5.5
0H
C 4
x3-1
01
43
8.5
3.0
911
.32
6.25
415
120.
397
15.8
814
.24
80.
687
511
.38
7.0
024
.41.
875
11.5
.50
HC
4x3
-10
14
38.
53.
09
11.3
26.
255
13.1
28
0.39
714
12.3
730.
687
510
.83
7.0
023
.85
1.87
511
.5.5
0H
C 6
x4-1
01
64
9.5
4.25
12.4
86.
53
16.8
7512
0.39
717
.75
16.1
230.
687
510
.83
7.0
025
.01
1.87
511
.5.5
0H
C 6
x4-1
01
64
9.5
4.25
12.4
86.
54
1512
0.39
715
.88
14.2
48
0.6
875
11.3
87.
00
25.5
61.
875
11.5
.50
HC
6x4
-10
16
49.
54.
2512
.48
6.5
513
.12
80.
397
1412
.373
0.6
875
10.8
37.
00
25.0
11.
875
11.5
.50
HC
8x6
-10
28
610
2.75
10.9
88.
251
20.8
7512
0.46
921
.75
20.1
250.
687
510
.83
7.0
029
.05
1.87
511
.5.5
0H
C 8
x6-1
02
86
102.
7510
.98
8.25
316
.875
120.
397
17.7
516
.123
0.6
875
10.8
37.
00
29.0
51.
875
11.5
.50
HC
8x6
-10
28
610
2.75
10.9
88.
254
1512
0.39
715
.88
14.2
48
0.6
875
11.3
87.
00
29.6
1.87
511
.5.5
0H
C 8
x6-9
52
86
102.
7510
.98
8.25
120
.875
120.
469
21.7
521
.125
0.6
875
10.8
37.
00
29.0
51.
875
11.5
.50
HC
8x6
-95
28
610
2.75
10.9
88.
253
16.8
7512
0.39
717
.75
16.1
230.
687
510
.83
7.0
029
.05
1.87
511
.5.5
0H
C 8
x6-9
52
86
102.
7510
.98
8.25
415
120.
397
15.8
814
.24
80.
687
511
.38
7.0
029
.61.
875
11.5
.50
HC
6x4
-13
26
411
614
.23
81
20.8
7512
0.46
921
.75
20.1
250.
687
510
.83
7.0
032
.85
2.5
11.5
.625
HC
6x4
-13
26
411
614
.23
83
16.8
7512
0.39
717
.75
16.1
230.
687
510
.83
7.0
032
.85
2.5
11.5
.625
HC
6x4
-13
26
411
614
.23
84
1512
0.39
715
.88
14.2
48
0.6
875
11.3
87.
00
33.
42.
511
.5.6
25H
C 5
x3-1
42
53
9.5
4.75
12.9
88.
51
20.8
7512
0.46
921
.75
20.1
250.
687
510
.83
7.0
031
.62.
511
.5.6
25H
C 5
x3-1
42
53
9.5
4.75
12.9
88.
53
16.8
7512
0.39
717
.75
16.1
230.
687
510
.83
7.0
031
.62.
511
.5.6
25H
C 5
x3-1
42
53
9.5
4.75
12.9
88.
.54
1512
0.39
715
.88
14.2
48
0.6
875
11.3
87.
00
32.1
52.
511
.5.6
25H
C 6
x6-1
42
66
10.5
5.19
13.4
29.
51
20.8
7512
0.46
921
.75
20.1
250.
687
510
.83
7.0
031
.16
2.5
11.5
.625
HC
6x6
-14
26
610
.55.
1913
.42
9.5
316
.875
120.
397
17.7
516
.123
0.6
875
10.8
37.
00
31.1
62.
511
.5.6
25H
C 6
x6-1
42
66
10.5
5.19
13.4
29.
54
1512
0.39
715
.88
14.2
48
0.6
875
11.3
87.
00
31.7
12.
511
.5.6
25H
C 8
x6-1
42
86
9.56
6.3
814
.61
4.81
120
.875
120.
469
21.7
520
.125
0.6
875
10.8
37.
00
32.3
62.
511
.5.6
25H
C 8
x6-1
42
86
9.56
6.3
814
.61
4.81
316
.875
120.
397
17.7
516
.123
0.6
875
10.8
37.
00
32.3
62.
511
.5.6
25H
C 8
x6-1
42
86
9.56
6.3
814
.61
4.81
415
120.
397
15.8
814
.24
80.
687
511
.38
7.0
032
.91
2.5
11.5
.625
HC
10x
10-1
42
1010
126.
2514
.48
121
20.8
7512
0.46
921
.75
20.1
250.
687
510
.83
7.0
032
.23
2.5
11.5
.625
HC
10x
10-1
42
1010
126.
2514
.48
123
16.8
7512
0.39
717
.75
16.1
230.
687
510
.83
7.0
032
.23
2.5
11.5
.625
HC
10x
10-1
42
1010
126.
2514
.48
124
1512
0.39
715
.88
14.2
48
0.6
875
11.3
87.
00
32.7
82.
511
.5.6
25
AØ
C
MP
Y
F
HØ
4 H
OLE
S
CP
(SU
CT
ION
)
BØ
EØKE
Y
(DIS
CH
AR
GE
)
X
G
DZ
FIG
UR
E 1
RO
TATI
ON
AØ
MP
FIG
UR
E 2
(DIS
CH
AR
GE
)
(SU
CT
ION
)
HØ
4 H
OLE
S
Y
F
J
CP
C
KE
Y
BØ
E
Z D
K
G
X
Mi8374 No
te:
Dim
ensi
ons
are
for
estim
atin
g pu
rpos
es o
nly.
Cer
tifi e
d di
men
sion
dra
win
gs a
re a
vaila
ble
on r
eque
st.
Centrifugal Pumps
Model Number ExplanationExample: 15XS4313-CCMLBD
15 = 15 Horsepower (CC only) XS = Centrifugal Series 4 = Suction Size 3 = Discharge Size 13 = Nominal Impeller Dia. CC = Close Coupled M = Shaft Sealing: P=Packing M=Mechanical Seal
LBD = Impeller Diameter (Alpha) A=0 F=5 L=10 B=1 G=6 M=11 C=2 H=7 N=12 D=3 J=8 P=13 E=4 K=9 Q=14
Features:■ Easy access packing area*
■ 2 piece stainless packing gland*
■ Fits industry standard JP motors
■ Hydraulically balanced impellers
■ Volute fl ow splitter in high capacity models
■ Stainless impeller standard on most models
■ Ease of service features include jack-out holes and lifting bosses
■ Easy retro-fi t industry standard suction, discharge and mounting bracket
* Applicable to packing seal models only.
XS SeriesStandard Centrifugal Pumps - Close Coupled
PAGE: CP-800DATE: Sep 1, 2008
XS-3x25-13 3” x 2.5”
10 1750 215JP 9-3/8 ODP Packing 10XS32513-CCPKDJ 70032513100 39010 1750 215JP 9-7/8 ODP Packing 10XS32513-CCPKJJ 70032513102 39015 1750 254JP 11-3/8 ODP Packing 15XS32513-CCPMDJ 70032513110 48315 1750 254JP 11-7/8 ODP Packing 15XS32513-CCPMJJ 70032513112 48320 1750 256JP 12-3/4 ODP Packing 20XS32513-CCPNHF 70032513120 53320 1750 256JP 13-1/16 ODP Packing 20XS32513-CCPPAG 70032513122 53310 1750 215JP 9-3/8 ODP Mech Seal 10XS32513-CCMKDJ 71032513101 39010 1750 215JP 9-7/8 ODP Mech Seal 10XS32513-CCMKJJ 71032513103 39015 1750 254JP 11-3/8 ODP Mech Seal 15XS32513-CCMMDJ 71032513111 48315 1750 254JP 11-7/8 ODP Mech Seal 15XS32513-CCMMJJ 71032513113 48320 1750 256JP 12-3/4 ODP Mech Seal 20XS32513-CCMNHF 71032513121 53320 1750 256JP 13-1/16 ODP Mech Seal 20XS32513-CCMPAG 71032513123 533
Ordering Information13” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor
Pump Model Suction/Disch. Size HP RPM Motor
FrameImpeller
TrimMotor
EnclosureShaft
SealingModel
DescriptionOrder
Number Weight
NOTES: There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Close Coupled
13” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor
Pump Model Suction/Disch. Size HP RPM Motor
FrameImpeller
TrimMotor
EnclosureShaft
SealingModel
DescriptionOrder
Number Weight
XS-4x3-13 4” x 3”
7.5 1750 213JP 8 ODP Packing 7XS4313-CCPJAA 70040313102 40210 1750 215JP 9-1/8 ODP Packing 10XS4313-CCPKBD 70040313100 41515 1750 254JP 10-3/4 ODP Packing 15XS4313-CCPLHF 70040313110 50820 1750 256JP 11-3/4 ODP Packing 20XS4313-CCPMHF 70040313120 55825 1750 284JP 12-5/16 ODP Packing 25XS4313-CCPNBD 70040313130 58530 1750 286JP 12-3/4 ODP Packing 30XS4313-CCPNHF 70040313140 59740 1750 324JP 13-1/6 ODP Packing 40XS4313-CCPPAG 70040313150 7307.5 1750 213JP 8 ODP Mech Seal 7XS4313-CCMJAA 71040313103 40210 1750 215JP 9-1/8 ODP Mech Seal 10XS4313-CCMKBD 71040313101 41515 1750 254JP 10-3/4 ODP Mech Seal 15XS4313-CCMLHF 71040313111 50820 1750 256JP 11-3/4 ODP Mech Seal 20XS4313-CCMMHF 71040313121 55825 1750 284JP 12-5/16 ODP Mech Seal 25XS4313-CCMNDB 71040313131 58530 1750 286JP 12-3/4 ODP Mech Seal 30XS4313-CCMNHF 71040313141 59740 1750 324JP 13-1/6 ODP Mech Seal 40XS4313-CCMPAG 71040313151 730
XS-6x4-13 6” x 4”
20 1750 256JP 9-3/8 ODP Packing 20XS6413-CCPKDJ 70060413100 57325 1750 284JP 10-1/4 ODP Packing 25XS6413-CCPLCF 70060413110 60030 1750 286JP 10-7/8 ODP Packing 30XS6413-CCPLJJ 70060413120 61230 1750 286JP 11-3/8 ODP Packing 30XS6413-CCPMDJ 70060413122 61240 1750 324JP 12-1/4 ODP Packing 40XS6413-CCPNCF 70060413130 74550 1750 326JP 12-7/8 ODP Packing 50XS6413-CCPNJJ 70060413140 87820 1750 256JP 9-3/8 ODP Mech Seal 20XS6413-CCMKDJ 71060413101 57325 1750 284JP 10-1/4 ODP Mech Seal 25XS6413-CCMLCF 71060413111 60030 1750 286JP 10-7/8 ODP Mech Seal 30XS6413-CCMLJJ 71060413121 61230 1750 286JP 11-3/8 ODP Mech Seal 30XS6413-CCMMDJ 71060413123 61240 1750 324JP 12-1/4 ODP Mech Seal 40XS6413-CCMNCF 71060413131 74550 1750 326JP 12-7/8 ODP Mech Seal 50XS6413-CCMNJJ 71060413141 878
XS-8x6-13 8” x 6”
25 1750 284JP 9-1/2 ODP Packing 25XS8613-CCPKFA 70080613150 68530 1750 286JP 10 ODP Packing 30XS8613-CCPLAA 70080613100 69740 1750 324JP 10-7/8 ODP Packing 40XS8613-CCPLJJ 70080613110 83040 1750 324JP 11-1/8 ODP Packing 40XS8613-CCPMBD 70080613112 83050 1750 326JP 11-5/8 ODP Packing 50XS8613-CCPMGD 70080613120 96360 1750 364TCZ 11-7/8 ODP Packing 60XS8613-CCPMJJ 70080613130 110960 1750 364TCZ 12-5/16 ODP Packing 60XS8613-CCPNBD 70080613132 110975 1750 365TCZ 12-1/2 ODP Packing 75XS8613-CCPNFA 70080613140 118375 1750 365TCZ 13 ODP Packing 75XS8613-CCMPAA 70080613142 118325 1750 284JP 9-1/2 ODP Mech Seal 25XS8613-CCMKFA 71080613151 68530 1750 286JP 10 ODP Mech Seal 30XS8613-CCMLAA 71080613101 69740 1750 324JP 10-7/8 ODP Mech Seal 40XS8613-CCMLJJ 71080613111 83040 1750 324JP 11-1/8 ODP Mech Seal 40XS8613-CCMMBD 71080613113 83050 1750 326JP 11-5/8 ODP Mech Seal 50XS8613-CCMMGD 71080613121 96360 1750 364TCZ 11-7/8 ODP Mech Seal 60XS8613-CCMMJJ 71080613131 110960 1750 364TCZ 12-5/16 ODP Mech Seal 60XS8613-CCMNDB 71080613133 110975 1750 365TCZ 12-1/2 ODP Mech Seal 75XS8613-CCMNFA 71080613141 118375 1750 365TCZ 13 ODP Mech Seal 75XS8613-CCMPAA 71080613143 1183
XS-10x8-13 10” x 8”
60 1750 364TCZ 9-13/16 ODP Packing 60XS10813-CCPKJB 70100813100 129475 1750 365TCZ 10-7/8 ODP Packing 75XS10813-CCPLJJ 70100813110 136875 1750 365TCZ 11-1/4 ODP Packing 75XS10813-CCPLCF 70100813112 1368100 1750 404TCZ 11-15/16 ODP Packing 100XS10813-CCPMKE 70100813120 1565100 1750 404TCZ 12-3/8 ODP Packing 100XS10813-CCPNDJ 70100813122 1565125 1750 444TCZ 12-3/4 ODP Packing 125XS10813-CCPNHF 70100813130 1888150 1750 445TCZ 13 ODP Packing 150XS10813-CCPPAA 70100813140 198160 1750 364TCZ 9-13/16 ODP Mech Seal 60XS10813-CCMKJB 71100813101 129475 1750 365TCZ 10-7/8 ODP Mech Seal 75XS10813-CCMLJJ 71100813111 136875 1750 365TCZ 11-1/4 ODP Mech Seal 75XS10813-CCMLCF 71100813113 1368100 1750 404TCZ 11-15/16 ODP Mech Seal 100XS10813-CCMMKE 71100813121 1565100 1750 404TCZ 12-3/8 ODP Mech Seal 100XS10813-CCMNDJ 71100813123 1565125 1750 444TCZ 12-3/4 ODP Mech Seal 125XS10813-CCMNHF 71100813131 1888150 1750 445TCZ 13 ODP Mech Seal 150XS10813-CCMPAA 71100813141 1981
Ordering Information
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8355
NOTES: There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Close Coupled
PAGE: CP-805DATE: Sep 1, 2008
NP
SH
r -
FE
ET
0
10
20
30
55050045040035020
300
40
250
60
80
200
100
120
150
140
100
160
180
500
200
65.9
13.062 in
12.75 in
11.875 in
11.375 in
9.875 in
9.375 in
7.5 hp
10 hp
15 hp
20 hp
40
40
50
50
50
50
55
55
55
60
60
63
63
65
65
TO
TAL
HE
AD
- F
EE
T
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE U.S. GALLONS PER MINUTE
FLOWRATE CUBIC METERS PER HOUR
55
5
10
15
20
25
30
35
40
45
50
55
60
120110100908070605040302010
SIZE: 3” x 2.5”IMPELLER DIA: VariousSPEED: 1750 RPM
Model XS-3x25-13
Centrifugal Pumps
Standard Centrifugal Pumps - Close CoupledXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8356
NP
SH
r -
FE
ET
0
5
10
15
20
10009008007006000
20
500
40
60
400
80
100
300
120
140
200
160
180
1000
200
78.5
13.062 in
12.75 in
12.312 in
11.75 in
10.75 in
9.125 in
8 in
5 hp
7.5 hp10 hp
15 hp
20 hp
25 hp
30 hp
40 hp
50
50
60
60
60
60
70
70
75
75
78
78
TO
TA
L H
EA
D -
FE
ET
FLOWRATE U.S. GALLONS PER MINUTE
0
10
20
30
40
50
60
TO
TA
L H
EA
D -
ME
TE
RS
230220210200190180170160150140130120110100908070605040302010
FLOWRATE CUBIC METERS PER HOUR
SIZE: 4” x 3”IMPELLER DIA: VariousSPEED: 1750 RPM
Model XS-4x3-13
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Close Coupled
PAGE: CP-810DATE: Sep 1, 2008
0
10
20
30
15001400130012001100100090020
800
40
700
60
600
80
500
100
400
120
300
140
200
160
1000
180
83.5
12.875 in
12.25 in
11.375 in
10.875 in
10.25 in
9.375 in
10 hp
15 hp
20 hp25 hp
40 hp 50 hp
68
68
72
72
76
76
76
76
80
80
80
82
82
82
8284
84
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
5
10
15
20
25
30
35
40
45
50
55
TO
TAL
HE
AD
- M
ET
ER
S
34032030028026024022020018016014012010080604020
FLOWRATE CUBIC METERS PER HOUR
SIZE: 6” x 4”IMPELLER DIA: VariousSPEED: 1750 RPM
80
30 hp
Model XS-6x4-13
Centrifugal Pumps
Standard Centrifugal Pumps - Close CoupledXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8357
0
5
10
15
2200200018001600140050
1200
75
1000
100
800
125
600
150
400
175
200
85.9
13 in
12.5 in
12.312 in
11.875 in
11.625 in
11.125 in
10.875 in
10 in
9.5 in
25 hp
30 hp
40 hp
50 hp
60 hp
75 hp
60
60
70
70
74
74
78
78
82
82
84
84
85
85
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
15
20
25
30
35
40
45
50
55
TO
TAL
HE
AD
- M
ET
ER
S
525500475450425400375350325300275250225200175150125100755025
FLOWRATE CUBIC METERS PER HOUR
SIZE: 8” x 6”IMPELLER DIA: VariousSPEED: 1780 RPM
Model XS-8x6-13
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Close Coupled
PAGE: CP-815DATE: Sep 1, 2008
0
10
20
30
5000450040003500300020
2500
40
60
2000
80
100
1500
120
1000
140
160
500
180
86.3
13 in
12.75 in
12.375 in
11.9375 in
11.25 in
10.875 in
9.8125 in
50 hp
60 hp
75 hp
100 hp
125 hp
150 hp
60
60
72
72
80
80
85
85
8686
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
10
15
20
25
30
35
40
45
50
55
115011001050100095090085080075070065060055050045040035030025020015010050
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 10” x 8”IMPELLER DIA: VariousSPEED: 1780 RPM
Model XS-10x8-13
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8358
Centrifugal Pumps
Model Number ExplanationExample: XS439-BFNP-CW
XS = Centrifugal Series 4 = Suction Size 3 = Discharge Size 9 = Nominal Impeller Dia. BF = Bearing Frame N = Connection: N=NPT V=Victaulic F=Flange
P = Shaft Sealing: P=Packing M=Mechanical Seal
CW = Rotation: CW=Clockwise CCW=Counter-Clockwise
XS-9 Series Features:■ Heavy duty bearing frame
■ Rugged 2-3/8” Stressproof ® shaft
■ 1-1/4” double keyed impeller shaft
■ Compact space saving design
■ Easy access packing area*
■ Easy retro-fi t with industry standard suction, discharge and mounting bracket
■ Diverse application options:
■ NPT & Victaulic volutes ■ CW & CCW rotations available
XS-13 Series Features:■ Rugged easy mount bearing frame
■ Heavy-duty 2-1/2” Stressproof ® shaft
■ 1-1/4” & 1-5/8” double keyed impellers
■ Easy access packing area with 2 piece stainless packing gland*
■ Ease of service features include jack-out holes and lifting bosses
■ Hydraulically balanced impellers
■ Volute fl ow splitter in high capacity models
■ Stainless impeller standard on most models
* Applicable to packing seal models only.
XS SeriesStandard Centrifugal Pumps - Bearing Frame
PAGE: CP-820DATE: Sep 1, 2008
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Bearing Frame
9” Nominal Impeller Diameter - (BF) Bearing Frame
Pump Model Suction/Disch. Size Rotation Volute
Design Shaft Seal Fit Impeller Material
Model Description Order Number Weight
XS-4x3-9 4” x 3”
CW NPT Packing Standard Cast Iron XS439-BFNP-CW 64040309100 135CCW NPT Packing Standard Cast Iron XS439-BFNP-CCW 64040309200 135CW Victaulic Packing Standard Cast Iron XS439-BFVP-CW 64040309101 135
CCW Victaulic Packing Standard Cast Iron XS439-BFVP-CCW 64040309201 135CW NPT Mech Seal Standard Cast Iron XS439-BFNM-CW 65040309100 135
CCW NPT Mech Seal Standard Cast Iron XS439-BFNM-CCW 65040309200 135CW Victaulic Mech Seal Standard Cast Iron XS439-BFVM-CW 65040309101 135
CCW Victaulic Mech Seal Standard Cast Iron XS439-BFVM-CCW 65040309201 135
XS-8x6-9 8” x 6”CW Flange Packing Standard Cast Iron XS869-BFP 64080609102 235CW Flange Mech Seal Standard Cast Iron XS869-BFM 65080609102 235
Ordering Information
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8359
13” Nominal Impeller Diameter - (BF) Bearing Frame
Pump Model Suction/Disch. Size Rotation Volute
Design Shaft Seal Fit Impeller Material
Model Description Order Number Weight
XS-3x25-13 3” x 2.5”CW Flange Packing Standard Bronze XS32513-BFP-CW 64030213102 261CW Flange Mech Seal Standard Bronze XS32513-BFM-CW 65030213102 261
XS-4x3-13 4” x 3”CW Flange Packing Standard Bronze XS4313-BFP-CW 64040313102 277CW Flange Mech Seal Standard Bronze XS4313-BFM-CW 65040313102 277
XS-6x4-13 6” x 4”CW Flange Packing Standard SS XS6413-BFP-CW 64060413102 294CW Flange Mech Seal Standard SS XS6413-BFM-CW 65060413102 294
XS-8x6-13 8” x 6”CW Flange Packing Standard SS XS8613-BFP-CW 64080613102 390CW Flange Mech Seal Standard SS XS8613-BFM-CW 65080613102 390
XS-10x8-13 10” x 8”CW Flange Packing Standard SS XS10813-BFP-CW 64100813102 575CW Flange Mech Seal Standard SS XS10813-BFM-CW 65100813102 575
NOTES: There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Bearing Frame
PAGE: CP-825DATE: Sep 1, 2008
40
50
60
70
80
90
1100100090080070040
600
60
80
500
100
120
400
140
160
300
180
200
200
220
240
1000
260
3000 rpm
2500 rpm
1750 rpm
7.5 hp
10 hp 15 hp20 hp
25 hp 30 hp40 hp
50 hp
60 hp
EF
FIC
IEN
CY
%
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
10
20
30
40
50
60
70
80
24022020018016014012010080604020
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE CUBIC METERS PER HOUR
SIZE: 4” x 3”IMPELLER DIA: 9”SPEED: Various
Model XS-4x3-9
Centrifugal Pumps
Standard Centrifugal Pumps - Bearing FrameXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8360
60
70
80
90
200018001600140050
1200
55
1000
60
65
800
70
600
75
80
400
85
200
902000 rpm
1900 rpm
1800 rpm
30 hp
40 hp
50 hp
EF
FIC
IEN
CY
%
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
16
17
18
19
20
21
22
23
24
25
26
27
475450425400375350325300275250225200175150125100755025
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE CUBIC METERS PER HOUR
SIZE: 8” x 6”IMPELLER DIA: 9”SPEED: Various
Model XS-8x6-9
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Bearing Frame
PAGE: CP-830DATE: Sep 1, 2008
0
10
20
30
40
6005505004504003500
50
300
100
250
150
200
200
250
150
300
100
350
50
400
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
15 hp20 hp
25 hp
30 hp
50 hp
50
5050
50
60
60
60
60
63
63
63
63
65
6540 hp
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
140130120110100908070605040302010
FLOWRATE CUBIC METERS PER HOUR
0
10
20
30
40
50
60
70
80
90
100
110
120
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 3” x 2.5”IMPELLER DIA: 13”SPEED: Various
Model XS-3x25-13
Centrifugal Pumps
Standard Centrifugal Pumps - Bearing FrameXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8361
0
10
20
30
40
13001200110010009008000
700
50
600
100
150
500
200
400
250
300
300
350
200
400
100
450
2600 rpm
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
15 hp
20 hp
25 hp 30 hp40 hp
50 hp 60 hp75 hp
100 hp
125 hp
50
50
60
60
60
60
70
70
70
70
75
75
75
75
78
78
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
10
20
30
40
50
60
70
80
90
100
110
120
130
28026024022020018016014012010080604020
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE CUBIC METERS PER HOUR
SIZE: 4” x 3”IMPELLER DIA: 13”SPEED: Various
Model XS-4x3-13
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Bearing Frame
PAGE: CP-835DATE: Sep 1, 2008
0
10
20
30
40
220020001800160014000
1200
50
1000
100
800
150
200
600
250
400
300
2000
350
82.9
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
25 hp30 hp
40 hp50 hp
60 hp75 hp
100 hp
125 hp
150 hp
60
60
60
60
72
72
78
78
78
82
82
82
82
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
0
10
20
30
40
50
60
70
80
90
100
110
TO
TAL
HE
AD
- M
ET
ER
S
500475450425400375350325300275250225200175150125100755025
FLOWRATE CUBIC METERS PER HOUR
SIZE: 6” x 4”IMPELLER DIA: 13”SPEED: Various
78
Model XS-6x4-13
Centrifugal Pumps
Standard Centrifugal Pumps - Bearing FrameXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8362
0
10
20
30
320028002400200050
1600
100
150
1200
200
250
800
300
350
4000
4002600 rpm
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
40 hp
50 hp60 hp
75 hp
100 hp
125 hp
150 hp
175 hp
200 hp
60 70
75
75
82
82
82
82
84
84
84
84
85
85
60 70
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
NP
SH
r -
FE
ET
20
30
40
50
60
70
80
90
100
110
120
130
75070065060055050045040035030025020015010050
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 8” x 6”IMPELLER DIA: 13”SPEED: Various
Model XS-8x6-13
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Bearing Frame
PAGE: CP-840DATE: Sep 1, 2008
0
10
20
30
40
4400400036003200280050
2400
75
100
2000
125
150
1600
175
1200
200
225
800
250
275
400
300
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
75 hp
100 hp
125 hp
150 hp
175 hp
200 hp
60
60
70
70
80
80
80
85
85
85
85
86
86
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
10
20
30
40
50
60
70
80
90
TO
TAL
HE
AD
- M
ET
ER
S
1050100095090085080075070065060055050045040035030025020015010050
FLOWRATE CUBIC METERS PER HOUR
SIZE: 10” x 8”IMPELLER DIA: 13”SPEED: Various
Model XS-10x8-13
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8363
Centrifugal Pumps
Model Number ExplanationExample: XS439-SA45NP
XS = Centrifugal Series 4 = Suction Size 3 = Discharge Size 9 = Nominal Impeller Dia. SA = SAE Engine Drive 45 = SAE Housing Size 45=4/5 23=2/3 N = Connection N=NPT V=Victaulic F=Flange P = Shaft Sealing: P=Packing M=Mechanical Seal
XS SeriesStandard Centrifugal Pumps - SAE Engine Drives
PAGE: CP-845DATE: Sep 1, 2008
XS-9 Series Features:■ Heavy duty bearing frame
■ Double drilled convertible SAE Bellhousings
■ Rugged 2-3/8” Stressproof ® shaft
■ 1-1/4” double keyed impeller
■ 1-1/2” 10 tooth splined input shaft for blind installations
■ Compact space saving design
■ Easy access packing area*
■ Easy retro-fi t with industry standard suction, discharge and mounting bracket
■ Diverse application options:
■ NPT & Victaulic volutes ■ CW & CCW rotations available
XS-13 Series Features:■ Rugged easy mount bearing frame
■ Heavy-duty 2-1/2” Stressproof ® shaft
■ 1-1/4” & 1-5/8” double keyed impellers
■ Easy access packing area with 2 piece stainless packing gland*
■ Ease of service features include jack-out holes and lifting bosses
■ Hydraulically balanced impellers
■ Volute fl ow splitter in high capacity models
■ Stainless impeller standard on most models
* Applicable to packing seal models only.
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - SAE Engine Drive
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8364
9” Nominal Impeller Diameter - (SA) SAE Engine Drive
Pump Model Suction/Disch. Size Rotation Volute
Design Shaft Seal Fit Impeller Material
Model Description Order Number Weight
XS-4x3-9 4” x 3”
CW NPT Packing 4/5 Cast Iron XS439-SA45NP 66040309145 150CW Victaulic Packing 4/5 Cast Iron XS439-SA45VP 66040309245 150CW NPT Packing 2/3 Cast Iron XS439-SA23NP 66040309123 150CW Victaulic Packing 2/3 Cast Iron XS439-SA23VP 66040309223 150CW NPT Mech Seal 4/5 Cast Iron XS439-SA45NM 67040309145 150CW Victaulic Mech Seal 4/5 Cast Iron XS439-SA45VM 67040309245 150CW NPT Mech Seal 2/3 Cast Iron XS439-SA23NM 67040309123 150CW Victaulic Mech Seal 2/3 Cast Iron XS439-SA23VM 67040309223 150
XS-8x6-9 8” x 6”
CW Flange Packing 4/5 Cast Iron XS869-SA45P 66080609345 250CW Flange Packing 2/3 Cast Iron XS869-SA23P 66080609323 250CW Flange Mech Seal 4/5 Cast Iron XS869-SA45M 67080609345 250CW Flange Mech Seal 2/3 Cast Iron XS869-SA23M 67080609323 250
Ordering Information
13” Nominal Impeller Diameter - (SA) SAE Engine Drive
Pump Model Suction/Disch. Size Rotation Volute
Design Shaft Seal Fit Impeller Material
Model Description Order Number Weight
XS-3x25-13 3” x 2.5”
CW Flange Packing 4/5 Bronze XS32513-SA45P 66032513345 345CW Flange Packing 2/3 Bronze XS32513-SA23P 66032513323 355CW Flange Mech Seal 4/5 Bronze XS32513-SA45M 67032513345 345CW Flange Mech Seal 2/3 Bronze XS32513-SA23M 67032513323 355
XS-4x3-13 4” x 3”
CW Flange Packing 4/5 Bronze XS4313-SA45P 66040313345 360CW Flange Packing 2/3 Bronze XS4313-SA23P 66040313323 370CW Flange Mech Seal 4/5 Bronze XS4313-SA45M 67040313345 360CW Flange Mech Seal 2/3 Bronze XS4313-SA23M 67040313323 370
XS-6x4-13 6” x 4”
CW Flange Packing 4/5 SS XS6413-SA45P 66060413345 370CW Flange Packing 2/3 SS XS6413-SA23P 66060413323 380CW Flange Mech Seal 4/5 SS XS6413-SA45M 67060413345 370CW Flange Mech Seal 2/3 SS XS6413-SA23M 67060413323 380
XS-8x6-13 8” x 6”
CW Flange Packing 4/5 SS XS8613-SA45P 66080613345 450CW Flange Packing 2/3 SS XS8613-SA23P 66080613323 460CW Flange Mech Seal 4/5 SS XS8613-SA45M 67080613345 450CW Flange Mech Seal 2/3 SS XS8613-SA23M 67080613323 460
XS-10x8-13 10” x 8”
CW Flange Packing 4/5 SS XS10813-SA45P 66100813345 635CW Flange Packing 2/3 SS XS10813-SA23P 66100813323 645CW Flange Mech Seal 4/5 SS XS10813-SA45M 67100813345 635CW Flange Mech Seal 2/3 SS XS10813-SA23M 67100813323 645
NOTES: There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - SAE Engine Drive
PAGE: CP-850DATE: Sep 1, 2008
40
50
60
70
80
90
1100100090080070040
600
60
80
500
100
120
400
140
160
300
180
200
200
220
240
1000
260
3000 rpm
2500 rpm
1750 rpm
7.5 hp
10 hp 15 hp20 hp
25 hp 30 hp40 hp
50 hp
60 hp
EF
FIC
IEN
CY
%
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
10
20
30
40
50
60
70
80
24022020018016014012010080604020
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE CUBIC METERS PER HOUR
SIZE: 4” x 3”IMPELLER DIA: 9”SPEED: Various
Model XS-4x3-9
Centrifugal Pumps
Standard Centrifugal Pumps - SAE Engine DriveXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8365
60
70
80
90
200018001600140050
1200
55
1000
60
65
800
70
600
75
80
400
85
200
902000 rpm
1900 rpm
1800 rpm
30 hp
40 hp
50 hp
EF
FIC
IEN
CY
%
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
16
17
18
19
20
21
22
23
24
25
26
27
475450425400375350325300275250225200175150125100755025
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE CUBIC METERS PER HOUR
SIZE: 8” x 6”IMPELLER DIA: 9”SPEED: Various
Model XS-8x6-9
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - SAE Engine Drive
PAGE: CP-855DATE: Sep 1, 2008
0
10
20
30
40
6005505004504003500
50
300
100
250
150
200
200
250
150
300
100
350
50
400
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
15 hp20 hp
25 hp
30 hp
50 hp
50
5050
50
60
60
60
60
63
63
63
63
65
6540 hp
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
140130120110100908070605040302010
FLOWRATE CUBIC METERS PER HOUR
0
10
20
30
40
50
60
70
80
90
100
110
120
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 3” x 2.5”IMPELLER DIA: 13”SPEED: Various
Model XS-3x25-13
Centrifugal Pumps
Standard Centrifugal Pumps - SAE Engine DriveXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8366
0
10
20
30
40
13001200110010009008000
700
50
600
100
150
500
200
400
250
300
300
350
200
400
100
450
2600 rpm
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
15 hp
20 hp
25 hp 30 hp40 hp
50 hp 60 hp75 hp
100 hp
125 hp
50
50
60
60
60
60
70
70
70
70
75
75
75
75
78
78
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
10
20
30
40
50
60
70
80
90
100
110
120
130
28026024022020018016014012010080604020
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE CUBIC METERS PER HOUR
SIZE: 4” x 3”IMPELLER DIA: 13”SPEED: Various
Model XS-4x3-13
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - SAE Engine Drive
PAGE: CP-860DATE: Sep 1, 2008
0
10
20
30
40
220020001800160014000
1200
50
1000
100
800
150
200
600
250
400
300
2000
350
82.9
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
25 hp30 hp
40 hp50 hp
60 hp75 hp
100 hp
125 hp
150 hp
60
60
60
60
72
72
78
78
78
82
82
82
82
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
0
10
20
30
40
50
60
70
80
90
100
110
TO
TAL
HE
AD
- M
ET
ER
S
500475450425400375350325300275250225200175150125100755025
FLOWRATE CUBIC METERS PER HOUR
SIZE: 6” x 4”IMPELLER DIA: 13”SPEED: Various
78
Model XS-6x4-13
Centrifugal Pumps
Standard Centrifugal Pumps - SAE Engine DriveXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8367
0
10
20
30
320028002400200050
1600
100
150
1200
200
250
800
300
350
4000
4002600 rpm
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
40 hp
50 hp60 hp
75 hp
100 hp
125 hp
150 hp
175 hp
200 hp
60 70
75
75
82
82
82
82
84
84
84
84
85
85
60 70
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
NP
SH
r -
FE
ET
20
30
40
50
60
70
80
90
100
110
120
130
75070065060055050045040035030025020015010050
FLOWRATE CUBIC METERS PER HOUR
TO
TAL
HE
AD
- M
ET
ER
S
SIZE: 8” x 6”IMPELLER DIA: 13”SPEED: Various
Model XS-8x6-13
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - SAE Engine Drive
PAGE: CP-865DATE: Sep 1, 2008
0
10
20
30
40
4400400036003200280050
2400
75
100
2000
125
150
1600
175
1200
200
225
800
250
275
400
300
2400 rpm
2200 rpm
2000 rpm
1800 rpm
1600 rpm
75 hp
100 hp
125 hp
150 hp
175 hp
200 hp
60
60
70
70
80
80
80
85
85
85
85
86
86
NP
SH
r -
FE
ET
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
10
20
30
40
50
60
70
80
90
TO
TAL
HE
AD
- M
ET
ER
S
1050100095090085080075070065060055050045040035030025020015010050
FLOWRATE CUBIC METERS PER HOUR
SIZE: 10” x 8”IMPELLER DIA: 13”SPEED: Various
Model XS-10x8-13
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8368
Centrifugal Pumps
Model Number ExplanationExample: XS869-HBFP-CW
XS = Centrifugal Series 8 = Suction Size 6 = Discharge Size 9 = Nominal Impeller Dia. HB = Hydraulic F = Connection N=NPT V=Victaulic F=Flange P = Shaft Sealing: P=Packing M=Mechanical Seal CW = Rotation: CW=Clockwise
Features:■ Heavy duty bearing frame
■ Rugged 2-3/8” Stressproof ® shaft
■ 1-1/4” double keyed impeller
■ Compact space saving design
■ Easy access packing area*
■ Easy retro-fi t with industry standard suction, discharge and mounting bracket
■ Diverse application options:
■ NPT & Victaulic volutes ■ CW & CCW rotations available
■ Available in both “B”(7/8” shaft) and “C”(1-1/4” shaft) fi ts
* Applicable to packing seal models only.
XS SeriesStandard Centrifugal Pumps - Hydraulic Motor Drive
PAGE: CP-870DATE: Sep 1, 2008
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Hydraulic Motor Drive
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8369
9” Nominal Impeller Diameter - (HB) Hydraulic
Pump Model Suction/Disch. Size Rotation Volute
Design Shaft Seal Fit Impeller Material
Model Description Order Number Weight
XS-4x3-9 4” x 3”
CW NPT Packing B Cast Iron XS439-HBNP-CW 68040309100 145CCW NPT Packing B Cast Iron XS439-HBNP-CCW 68040309200 145CW Victaulic Packing B Cast Iron XS439-HBVP-CW 68040309101 145
CCW Victaulic Packing B Cast Iron XS439-HBVP-CCW 68040309201 145CW NPT Mech Seal B Cast Iron XS439-HBNM-CW 69040309100 145
CCW NPT Mech Seal B Cast Iron XS439-HBNM-CCW 69040309200 145CW Victaulic Mech Seal B Cast Iron XS439-HBVM-CW 69040309101 145
CCW Victaulic Mech Seal B Cast Iron XS439-HBVM-CCW 69040309201 145CW NPT Packing C Cast Iron XS439-HCNP-CW 68040309300 145
CCW NPT Packing C Cast Iron XS439-HCNP-CCW 68040309400 145CW Victaulic Packing C Cast Iron XS439-HCVP-CW 68040309301 145
CCW Victaulic Packing C Cast Iron XS439-HCVP-CCW 68040309401 145CW NPT Mech Seal C Cast Iron XS439-HCNM-CW 69040309300 145
CCW NPT Mech Seal C Cast Iron XS439-HCNM-CCW 69040309400 145CW Victaulic Mech Seal C Cast Iron XS439-HCVM-CW 69040309301 145
CCW Victaulic Mech Seal C Cast Iron XS439-HCVM-CCW 69040309401 145
XS-8x6-9 8” x 6”
CW Flange Packing B Cast Iron XS869-SA45P 68080609102 245CW Flange Mech Seal B Cast Iron XS869-SA23P 69080609102 245CW Flange Packing C Cast Iron XS869-SA45M 68080609302 245CW Flange Mech Seal C Cast Iron XS869-SA23M 69080609302 245
Ordering Information
NOTES: There will be an impeller trimming charge applied for any non-standard impeller trim. Consult price sheets for list price adders.
Centrifugal Pumps
XS SeriesStandard Centrifugal Pumps - Hydraulic Motor Drive
PAGE: CP-875DATE: Sep 1, 2008
40
50
60
70
80
90
1100100090080070040
600
60
80
500
100
120
400
140
160
300
180
200
200
220
240
1000
260
3000 rpm
2500 rpm
1750 rpm
7.5 hp
10 hp 15 hp20 hp
25 hp 30 hp40 hp
50 hp
60 hp
EF
FIC
IEN
CY
%
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
10
20
30
40
50
60
70
80
24022020018016014012010080604020
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE CUBIC METERS PER HOUR
SIZE: 4” x 3”IMPELLER DIA: 9”SPEED: Various
Model XS-4x3-9
Centrifugal Pumps
Standard Centrifugal Pumps - Hydraulic Motor DriveXS Series
400 E. Spring St., Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.comMi8370
60
70
80
90
200018001600140050
1200
55
1000
60
65
800
70
600
75
80
400
85
200
902000 rpm
1900 rpm
1800 rpm
30 hp
40 hp
50 hp
EF
FIC
IEN
CY
%
TO
TAL
HE
AD
- F
EE
T
FLOWRATE U.S. GALLONS PER MINUTE
16
17
18
19
20
21
22
23
24
25
26
27
475450425400375350325300275250225200175150125100755025
TO
TAL
HE
AD
- M
ET
ER
S
FLOWRATE CUBIC METERS PER HOUR
SIZE: 8” x 6”IMPELLER DIA: 9”SPEED: Various
Model XS-8x6-9
Repair Parts
Service Parts KitsOrdering Information by Pump Model & Size
PAGE: RP-100DATE: June 5, 2006
DDD Repair Kits
Includes impeller, square ring, mechanical seal, wear-ring, and fastenersDescription Part Number Repair Models
Impeller Kit
05388608K 5DD105388707K 7DD105388806K 1DD105388905K 15DD105389002K 2DD105389101K 25DD1
Fastener Kit 14443402K Repairs all DDD models
Seal, O-ring Kit 24017345 Includes Mechanical Seal & O-ring
DA1A & DAIB Repair Kits
Includes impeller, mechanical seal, & o-ringDescription Part Number Repair Models
Impeller Kit
05394606K 3DA1A05394705K 5DA1A05394903K 7DA1A05394804K DA1A05394101K 7DA1B & 1DA1B05394200K 15DA1B05394309K 2DA1B
Fastener 14443303K DA1A, DA1B, RM2,RP2, RP3,HJM1, & HJM2
Seal, O-Ring Kit 24017352 Includes Mechanical Seal & O-Ring
DB1 & DB1-1/2 Repair KitsIncludes impeller, mechanical seal, impeller jam nut, and o-ring
Description Part Number Repair Models
Impeller Kit
05371109K 7DB105163209K 1DB105163803K 15DB105164306K 2DB105165303K 3DB1
Fastener Kit 14443501K DB1-1/2, DB2, DC1-1/2
Seal Sleeve Kit 24017279 Includes all o-rings & imp.
Fasteners See Parts Page for details.
Seal, O-Ring Kit 24017352 Includes Mech. Seal & O-ring
Repair Parts
Service Parts KitsOrdering Information by Pump Model & Size
Mi8510
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
DB2 Repair Kits
Includes Impeller, Mechanical Seal, Impeller Jam-Nut and O-Ring
Description Part Number Repair Models
Impeller Kit05152103K 15DB2
05152004K 2DB2
05169503K 3DB2
Fastener Kit 14443501K DB2, DB1-1/2, DC1-1/2
Seal Sleeve Kit 24017279 Includes O-rings & impeller fasteners (See parts pages.)
Seal, O-ring Kit24017378 Includes all O-Rings and mechanical seals for 20DB2
24017352 Includes mechanical seals and O-Rings for 3/4 - 3 HP
DC1-1/2 Repair KitsFastener Kit 14443501K DC1-1/2, DB2, DB1-1/2
Seal Sleeve Kit 24017279 Includes O-Rings and impeller fasteners (See parts pages)
DB3 Repair KitsFastener Kit 14443600K Repairs all DB3 models
Seal Sleeve Kit 24017279 Includes O-Rings & impeller fasteners for 5HP thru 15HP
Seal Sleeve Kit 24017295 Includes O-Rings & impeller fasteners for 20HP
Seal O-Ring Kit 24017360 Includes mechanical seal & O-Rings for 5HP thru 15HP
Seal O-ring 24017378 Mechanical seal & O-Ring for 20HP
DC4 Repair KitsFastener Kit 14443709K Repairs all DC4
Seal Sleeve Kit 24017295 O-Rings & imp. fasteners for 20HP-50HP
Seal O-Ring Kit 24017378 Mech. seal, square & o-rings for 20HP thru 50HP
JM-8M-10M Repair KitsFastener Kit 14443808K Repairs all JM, 8M, 10M
Seal Gasket Kit 24017386 Mechanical Seal and gaskets
Chk Valve Assy Kit 16030900R Housing, gasket, fl apper, & fasteners
HJM1 – HJM2 Repair KitsIncludes Impeller, Diffuser, Mechanical Seal, Wear-Ring, O-Ring, and Fasteners
Impeller Kit
05077615RKIT HJM1 & 2 Plastic 1HP Unit
24017303 1HJM1Brz. 1HP full rate 1.5HP uprate
24017311 1.5HJM1Brz. 1.5HP full rate 2HP uprate
24017329 2HJM1Brz. 2HP full rate 2.5HP uprate
05273800RKIT 1HJM1 & 2 plastic 1 HP full rate 1.5HP uprate
05272703RKIT 1.5HJM1 & 2 plastic 1.5HP full rate 2HP uprate
05326707RKIT 2HJM1 & 2 Brz. 2HP full rate 2.5HP uprate
Fastener Kit 14443303K Repairs all HJM1 – HJM2
Repair Parts
Service Parts KitsOrdering Information by Pump Model & Size
PAGE: RP-105DATE: June 5, 2006
CY-CCY & SWJ Repair KitsIncludes impeller, diffuser, wear ring, mechanical seal, o-ring & disc
Description Part Number Repair Models
Impeller Kit05380037RKIT S5CY – S5CCY05392204RKIT 5CY – S7CY – 5CCY – S7CCY – 5SWJ05392303RKIT 7CY – S1CY – 7CCY – S1CCY – 7SWJ
Fastener Kit 14443204K Cyclone, Deep, SRP3, CWJ, SWJ
RP2 Repair KitsIncludes impeller, diffuser, wear ring, mechanical seal, & square ring
Impeller Kit 24012106 5RP224012205 7RP2
Fastener 14443303K RP2, RM2, PRM3, DA1A, DA1B, HJM1, HJM2, CWJ Pro
Seal, Square Ring Kit 24012304 Includes mech. seal & all o-rings and square rings
Impeller Kit
24014508 5RM2, 5CWJ Pro24014607 7RM2, 7CWJ Pro24014904 1RM2, 1CWJ Pro24017246 1PRM3
RM2, CWJ Pro & 7PRM3 Repair KitsImpeller Kit, The following kits are for units built prior to 7/96 and will include a 9/16” threaded motor coupling
Impeller Kit24012403 5RM2, 5CWJ Pro24012502 7RM2, 7CWJ Pro24012601 1RM2, 1CWJ Pro
Fastener Kit 14443303K RM2, PRM3, RP2, DA1A, DA1B, HJM1, HJM2, CWJ Pro
Seal, Square Ring Kit 24012700 Includes mech. seal & all o-ring and square rings
V6 Booster Repair KitsDescription Part Number Repair Models
Fastener Kit 14444004K Repairs all V6 Boosters
H4 Booster Repair KitsDescription Part Number Repair Models
H4 Component Kit 24017519 Small Parts for all models
Fastener Kit 14443907K Repairs all H4 Boosters
Typhoon, TY, TYCI Hydraulic Repair KitsIncludes impeller, diffuser, wear ring, mechanical seal, square ring, and o-ring.
Description Part Number Repair Models
Impeller Kit
05034103RKIT 7TY, S10TY, 7TYCI05034202RKIT 10TY, S15TY, 10TYCI05034400RKIT 15TY, S20TY, 15TYCI05034001RKIT 20TY, S25TY, 20TYCI
Mi8511
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Repair Parts
4” Submersible PartsParts for all Models (35-90 GPM)
PAGE: RP-106DATE: Feb 5, 2007
Mi8512
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklin-electric.com
1
2
3
4
5
7
12
8
9
14
15
13
12
6
10
11
16
19
17
18
Fig. No. Part No. Description
1 03-0905-03-R 2" Stainless Steel Discharge Housing w/ rubber bearing04-5340-04-R Cast Iron Disch. Housing w/ rubber bearing (prior to 8/01) DISCONTINUED
2 08-2888-05-R Rubber Bearing
3 02-1707-02-R Stainless Steel Hi-Cap Bracket02-1134-05-R Cast Iron Mtr. Bracket (prior to 8/01) DISCONTINUED Stainless Steel replaces
4 14-4347-08-R Stainless Hex Nut 5/16-24 w/ Nylock5 14-0756-00-R Stainless Steel Washer 11/32 D x 5/8 x 1/166 14-1249-03-R Brs. Washer .065 x .050 x .0037 08-2903-06-R Hub Sleeve Hex 7/16 x 468 L Ceramic (6 ea. required)8 14-4223-07-R Thrust Washer 1-5/16 x .71 x 1/8 (not required on 35 gpm model)9 08-2893-08-R Thrust Journal (not required on 35 gpm model)
10
04-5783-08-R 35 gpm Stage Assembly (1 x no of stages required)04-5341-03-R 45 gpm Stage Assembly (1 x no. of stages required)04-5343-01-R 60 gpm Stage Assembly (1 x no. of stages required)04-5300-02-R 90 gpm Stage Assembly (1 x no. of stages required)
11 08-2506-23-R Hex Sleeve 7/16 x 1 L (1 x no. of stages required) (45 & 60 gpm models only)
12 08-2960-06-R Hex Sleeve .460" (2 ea. for 35 gpm & 1ea. for all other models)08-2506-23-R Hex Sleeve 7/16 x 1 L (2 required only for models built prior to 8/01)
1322-5925-05-R Screen 302 Stainless Steel 1.50 x 12 for 35 thru 90 gpm22-0579-05-R Screen (units built prior to 8/01)
14 14-3914-03-R Fastener Kit (4 ea. per kit) with #22569404 lead protector15 14-4412-08-R Fastener Kit 8/32 x 1/4 MS Hex Wash. 410 Stainless Steel (2 ea. per kit)16 08-2961-05-R Bearing Support Stage w/ bearing 35 gpm thru 90 gpm models17 Not Available Pump Shell - not sold as a replacement part18 Shaft Assembly Consult Factory for size and availability19 Cable shield Consult Factory for size and availability
Repair Parts
6” Submersible PartsParts for all Models (60-75 GPM)
PAGE: RP-110DATE: June 5, 2006
Mi8500
7
6
5
4
3
2
1
8
9
Figure No. Part No. Description1 02-1708-01-R S.S. Bracket (All HP's)
2 Shell Consult Factory for Size and Availability
304-5648-03 50 GPM Stage assembly for 1.5 & 2HP04-5647-04 50 GPM Stage assembly for 3, 5, 7.5, & 10HP04-5649-02 75 GPM Stage assembly for 3 & 5HP04-5650-08 75 GPM Stage assembly for 7.5, 10, 15 & 20HP
4 04-5820-03-R S.S. Discharge (3" NPT)
5 22-5957-08-R S.S. Screen with Machine Screws (2 each)
6 14-4421-07 4" & 6" Motor Fastener Kit
7 Cable Shield Consult Factory for Size and Availability
8 04-5848-01-R Bearing and Spacers Repair Kit
9 Shaft Consult Factory for Size and Availability
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Repair Parts
Model DDD & DDSParts for Centrifugal Pumps
PAGE: RP-115DATE: June 5, 2006
Mi8501
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
14
8
#7Base Kit
9
2#5 Impeller Kit
3
4 5
12 13
#6 Case Kit
11
Figure No. Part No. C.I. Part No. S.S. Description
2 11-1498-04-R Seal Plate Cast Iron #11293 for DDD, RCFC11-0063-01-R Seal Plate Stainless Steel for DDS
3 47-0258-53-02PK 47-0258-53-02PK Square-Ring Kit 6 x 1/8 x 1/8 (2 per kit)
4 10-0002-06 Mechanical Seal 5/8 for DDD, RCFC Models10-1436-18 Mechanical Seal 5/8 Viton for DDS Models
All Impeller Kits include; Impeller, Sq.-Ring, Mech. Seal, Wear-Ring and fasteners Fig No’s 3,4,5,12,13
5
05-3886-08-K 05-3886-16-K 1/2 HP Impeller Kit 4.605 dia. #1137505-3887-07-K 05-3887-15-K 3/4 HP Impeller Kit 5.0 dia. #1137605-3888-06-K 05-3888-14-K 1 HP Impeller Kit 5.25 dia. #1137705-3889-05-K 05-3889-13-K 1.5 HP Impeller Kit 5.315 dia. #1137805-3890-02-K 2 HP Impeller Kit 5.65 dia. #1133805-3891-01-K 2.5 HP Impeller Kit 5.95 dia. #11379
603-0850-08-R 03-0850-17-R Case Assembly Kit #11337 w/ plugs #11 for 1/2HP thru 1/5HP03-0851-07-R Case Assembly Kit #11338 w/ plugs #11 for 2HP03-0852-06-R Case Assembly Kit #11338 w/ plugs #11 for 1/2HP thru 1/5HP
7 12-1057-06-R 12-1057-06-R Base Assembly Kit w/ motor pad #8 for 48 frame motor12-1060-03-K 12-1060-06-K Base Assembly Kit w/ motor pad #8 for 56 frame motor
9 & 13 14-4434-02-K 14-4434-02-K *Fastener Kit
11 31-0059-11-06PK 31-0059-11-06PK Plug Kit 1/4” Galv. (6 per kit)
12 08-0845-19-06PK 08-0845-19-06PK Wear-Ring Kit (6 per kit)
13 14-4353-09 14-4353-09 Capscrew 1/4-20 x 1-3/16 LG LH Hx. / Wash. for 2HP 3Ph.14-4354-08 14-4354-08 Capscrew 1/4-20 x 7/8 LG LH Hx. / Wash. for 1/2 thru 1/5HP 3 Ph.
14 Motor Motor See Motor Selection Page
*Fastener Kit #14443402-K includes the following:4 each 3/8 - 16 x 1-1/8 PL Hex Capscrews #91 each 1/4 - 20 x 7/8 Hex Wash-Capscrews for 1/2 HP thru 1/5 HP 3PH. #131 each 1/4 - 20 x 1-3/6 Hex Wash-Capscrews for 2HP 3PH. #13
Repair Parts
2 3 7
5
6
6
4
8
#3 Impeller Kit
Figure No. Part. No. Description1 02-0905-04-R DA1A Bracket #3220 4-1/2”M x 5-3/16 w/fateners #6
2 03-0763-04-R DA1A/B, Case assembly #3405 1-1/4 x 1 w/plugs**Note- When replacing impeller for units built prior to 7/96,
you must also replace the 7/16 thrd. Cplg. with the 9/16 threaded couling #07361009-R001.All Impeller Kits include; impeller, mech. seal & O-ring Fig. No’s 3,5 & 7.
3
**05-3946-06-K Impeller Kit #2794 @ 3-3/16 w/ 9/16T for 3DA1A**05-3947-05-K Impeller Kit #2794 @ 4-1/8D w/ 9/16T for 5DA1A**05-3949-03-K Impeller Kit #2794 @ 4-11/16D w/ 9/16T for 7DA1A**05-3948-04-K Impeller Kit #2794 @ 5-11/16D w/ 9/16T for 1DA1A**05-3941-01-K Impeller Kit #4607 @ 4-1/4D w/ 9/16T for 7DA1B & 1DA1B**05-3942-00-K Impeller Kit #4607 @ 4-11/16D w/ 9/16T for 1.5DA1B**05-3943-09-K Impeller Kit #4607 @ 5-1/16D w/ 9/16T for 2DA1B
4**07-2152-05-R001 Coupling w/set screws (for units built prior to 7/96) 7/16 thread**07-3610-09-R001 Coupling w/set screws (for units built after 7/96) 9/16 thread
5 10-1203-01 Mechanical Seal 3/4 (also included with impeller kits)
6* 14-4433-03-K *Fastener Kit
7 47-0161-00-02PK O-Ring Kit 5-1/2 x 5-11/16 x 3/32 BN (2 ea. per kit)
8 Motor See Motor Selection Page
Kit 24-0173-52 Seal O-Ring Kit includes: Mech. Seal & O-Ring fi g. #’s: 5,7
*Fastener Kit #14443303-K includes the following:8 each 3/8-16 x 3/4 PL Hex Capscrews
Model DA1A & DA1BParts for Centrifugal Pumps
PAGE: RP-120DATE: June 5, 2006
Repair Parts
Model DB1 & DB1-1/2Parts for Centrifugal Pumps
Mi8502
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
14 13 12 9 11
Seal Sleeve Kit
2
14 1312 38
5
17
6 1
4
16
7
15
109 11
Figure No. Part No. Description
1 02-1264-07-R Bracket Assembly #3299 4-1/2” x 6-1/2” 3/4HP thru 3HP w/base#1502-1590-02-R Bracket Assembly #9319 4-1/2” x 6-1/2”, 5HP & 7.5HP
2 03-0764-02-R Case Assembly #3393 w/pugs for DB103-0767-00-R Case Assembly #3393 w/plugs for DB1-1/2
All Impeller Kits include: Impeller, Mech. Seal, Jam-Nut, O-Ring Fig. No’s 3,5,8,17
3
05-3711-09-R Impeller Kit #11239 @ 4-1/4D w/9/16T for 3/4HP DB105-1632-09-R Impeller Kit #11239 @ 4-3/4D w/9/16T for 1HP DB105-1638-03-R Impeller Kit #11239 @ 5-3/16D w/9/16T for 1.5HP DB105-1643-06-R Impeller Kit #11239 @ 5-1/2D w/9/16T for 2HP DB103-1653-03-R Impeller Kit #11239 @ 6-1/8D w/9/16T for 3HP DB105-1790-23-R Impeller Kit #3392 @ 6-7/16D w/7/8B for 5HP DB105-3709-03-R Impeller Kit #3398 @ 3-15/16D w/9/16T for 1HP DB1-1/205-3710-00-R Impeller Kit #3398 @ 4-5/16D w/9/16T for 1.5HP DB1-1/205-1665-09-R Impeller Kit #3398 @ 4-11/16D w/9/16T for 2HP DB1-1/205-1673-09-R Impeller Kit #3398 @ 5-1/8D w/9/16T for 3HP DB1-1/205-1816-23-R Impeller Kit #3398 @ 5-3/4D w/7/8B for 5HP DB1-1/205-1823-24-R Impeller Kit #3398 @ 6-7/16D w/7/8B for 7.5HP DB1-1/2
4 07-3610-09-R001 Shaft Coupling 9/16” thrd. w/setscrews for 3/4HP thru 3HP
5 10-1203-01 Mechanical Seal 3/4 for 3/4HP thru 3HP (also is included w/imp. kit)10-0369-03 Mechanical Seal 1-1/4” for 5HP thru 7.5HP
6,7,12-14,17 14-4435-01-K *Fastener Kit
8 47-0165-06-02PK O-Ring 6-1/2 x 6-11/16 x 3/32 B-N (2 ea. per kit) (also is included w/imp. kit)
9 47-0022-09-02PK O-Ring Kit for 5HP & 7.5HP (2ea. per kit)
10 08-2872-03-R Seal Sleeve 1-1/4” x 1” SS for 5HP & 7.5HP
11 13-0384-01-02PK O-Ring Kit for 1” Sleeve for 5HP & 7.5HP (2ea. per kit)
Sleeve Kit 24-0172-79 Seal Sleeve Kit for 5HP & 7.5HP; includes #’s 8,9,12,13,14
15 12-1036-02-R Base w/fasteners for 3/4HP thru 3HP
16 Motor See Motor Selection Page
17 14-4420-08-06PK Jam Nut Kit 9/16-18 NF SS eff. 1/30/02 for DB1-1/2 2HP & 3HP 3ph (6ea. per kit)
Kit 24-0173-52 Seal/O-Ring Kit for 3/4HP thru 3HP; includes #5 the 3/4” mech. seal & #8
*Fastener Kit #14443501K includes the following:8 each 3/8 - 16 x 3/4 PL. Hex Capscrews4 each 3/8 - 16 x 1-1/2 PL Hex Capscrews #7 for 5 & 7.5HP 3ph4 each 1/2 - 13 x 1-1/4 PL Hex Capscrew #7 for 7.5 1phAlso included in Kit are #12,13,14,& 17.
Repair Parts
Model DB2 & DC2Parts for Centrifugal Pumps
PAGE: RP-125DATE: June 5, 2006
14 13 12 9 11
Seal Sleeve Kit8
2
14 1312 38
5
17
6 1
4
16
7
15
109 11
Figure No. Part No. Description
1
02-1264-07-R Bracket #3299 4-1/2 x 6-1/2 1.5-3HP w/#1502-1590-02-R Bracket #9319 4-1/2 x 6-1/2 5-7.5HP02-1564-04-R Bracket #9141 8-1/2 x 6-1/2 10HP02-1263-08-R Bracket #9142 8-1/2 x 9 20HP02-1565-03-R Bracket #9142 8-1/2 x 9C 15HP
2 03-0766-01-R Case #3294 for 1.5HP thru 10HP03-0762-05-R Case #11235 for 15HP thru 20HP
All Impeller Kits include: Impeller, Mech. Seal, Jam-Nut, & O-Ring. for 1.5-3HP Fig. No’s 3,5,8,17
3
05-1521-03-R Impeller Kit #3293 @ 3-13/16”D for 1/5HP05-1520-04-R Impeller Kit #3293 @ 4”D for 2HP05-1695-03-R Impeller Kit #3293 @ 4-1/2”D for 3HP05-1738-28-R Impeller Kit #3293 @ 5-1/8”D for 5HP05-1749-25-R Impeller Kit #3293 @ 5-13/16”D for 7.5HP05-1759-22-R Impeller Kit #3293 @ 6-7/16”D for 10HP05-3719-19-R Impeller Kit #3185 @ 7-1/4”D for 15HP05-3703-17-R Impeller Kit #3185 @ 7-15/16”D for 20HP
4 07-3610-09-R001 Shaft Coupling 9/16” thrd. for 1.5HP thru 3HP
510-1203-01 Mechanical Seal 3/4” for 1.5HP thru 3HP10-0369-03 Mechanical Seal 1-1/4” for 5HP thru 15HP10-0370-00 Mechanical Seal 1-3/4” for 20HP
6,7,12-14,17 14-4435-01-K *Fastener Kit
8 47-0165-06-02PK O-Ring Kit for 5HP thru 10HP (2 per kit)47-0175-04-02PK O-Ring Kit for 15HP & 20HP (2 per kit)
9 47-0022-09-02PK O-Ring Kit for 5HP thru 10HP (2 per kit)47-0126-04-02PK O-Ring Kit for 15HP & 20HP (2 per kit)
10 08-2872-03-R Seal Sleeve 1-1/4” x 1” for 5HP thru 10HP08-2909-00-R Seal Sleeve 1-3/4” x 1-3/8” for 15HP thru 20HP
11 13-0384-01-02PK O-Ring Kit 5HP thru 10HP (2 per kit)13-0385-00-02PK O-Ring Kit for 15HP thru 20HP (2 per kit)
Sleeve Kit 24-0172-79 Seal Sleeve Kit for 5HP thru 10HP includes fi g no’s 8,9,11,12,13, & 14
15 12-1036-02-R Base w/fasteners for 3/4HP thru 3HP
16 Motor See Motor Selection Page
17 14-4420-08-06PK Jam Nut Kit 9/16-18 NF SS eff. 2/02 (6 per kit) used on DB2 thru 3HP
Kit 24-0173-52 Seal/O-Ring Kit 3/4-3HP includes #5,8
Kit 24-0173-60 Seal/O-Ring Kit 5-15HP includes #5,8,9,11
Kit 24-0173-78 Seal/O-Ring Kit 20HP includes #5,8,9,11
*Fastener Kit #14443501K includes the following:8 each 3/8 - 16 x 3/4 PL Hex Capscrews #64 each 3/8 - 16 x 1-1/2 PL Hex Capscrews #7 5-7.5HP4 each 1/2 - 13 x 1-1/4 PL Hex Capscrews #7 7.5HP 1phand 10HP - also included in kit are #12,13,14, & 17
Repair Parts
Model DC1-1/2Parts for Centrifugal Pumps
Mi8503
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
213 11
34
13 12 11 8 7
6
9 1
14
785
9-10
Seal Sleeve Kit
12
4
Figure No. Part No. Description
102-1593-09-R Bracket #9340 4-1/2” x 9” for 3HP, 5HP, 7.5HP02-1565-03-R Bracket #9142 8-1/2” x 9” for 10HP & 15HP
2 03-0765-02-R Case Assembly #3272 for DC1-1/2
3
05-3721-07-R Impeller #11233 @ 5-1/16” dia. 3HP DC1-1/205-3723-05-R Impeller #11233 @ 5-13/16” dia. 5HP DC1-1/205-3725-03-R Impeller #11233 @ 6-5/8” dia. 7.5HP DC1-1/205-3714-06-R Impeller #11233 @ 7-5/16” dia. 10HP DC1-1/205-3702-00-R Impeller #11233 @ 8-3/8” dia. 15HP DC1-1/2
4 47-0175-04-02PK O-Ring Kit 9 x 9-3/16 x 3/32 B-N (2 per kit)
5 08-2872-03-R Seal Sleeve 1-1/4” x 1” SS for 3HP thru 15HP
6 10-0369-03 Mechanical Seal 1-1/4” for 3HP thru 15HP
7 13-0384-01-02PK O-Ring Kit 1” shft. B-N for 3HP thru 15HP (2 per kit)
8 47-0022-09-02PK O-Ring Kit 1” x 1-1/8 x 1/16 B-N for 3HP thru 15HP (2 per kit)
9 thru 13 14-4435-01-K *Fastener Kit
Sleeve Kit 24-0172-79 Seal Sleeve Kit for 3HP thru 15HP includes #’s 4,7,8,11,12, & 13
14 Motor See Motor Selection Page
Kit 24-0173-60 Mechanical Seal - O-Ring Kit for 3 to 15HP includes #’s 5,6,7, & 8
*Fastener Kit #14443501K includes the following:12 each 3/8 - 16 x 3/4 PL Hex Capscrews #94 each 1/2 - 13 x 1-1/4 PL Hex Capscrews #101 each 3/16 x 1-1/8 Square Key #111 each 1-1/8 x 13/32 x 1/8 Impeller washer #121 each 3/8 - 16 x 3/4 HT/TR Capscrew #13
Repair Parts
Model DB3Parts for Centrifugal Pumps
PAGE: RP-130DATE: June 5, 2006
7 11 10 6 13
Seal Sleeve Kit
2
15 7 1110
314
5
81
16
94 6 13
12
Figure No. Part No. Description
102-1590-02-R Mtr. Bracket #9319 4-1/2”M x 6-1/2”C for 5HP & 7.5HP02-1564-04-R Mtr. Bracket #9141 8-1/2”M x 6-1/2”C for 10HP & 15HP02-1390-04-R Mtr. Bracket 8-1/2”M x 6-1/2”C for 20HP
2 03-0840-01-R Case #11342 4 x 3 C.I. for DB3
3
05-3837-08-R Impeller #11340 4-1/2” dia. for 5HP DB305-3838-07-R Impeller #11340 4-15/16” dia. for 7.5HP DB305-3839-06-R Impeller #11340 5-15/16” dia. for 10HP DB305-3840-03-R Impeller #11340 5-3/4” dia. for 15HP DB305-3841-02-R Impeller #11341 6” dia. for 20HP DB3
4 08-2872-03-R Seal Sleave 1-1/4” x 1” SS for 5HP thru 15HP08-2909-00-R Seal Sleeve 1-3/4” x 1-3/8” SS for 20HP
5 10-0369-03 Mechanical Seal 1-1/4” for 5HP thru 15HP10-0370-00 Mechanical Seal 1-3/4” for 20HP
6 13-0384-01-02PK Sleeve O-Ring Kit 1” shft. B-N for 5HP thru 15HP (2 per kit)13-0385-00-02PK Sleeve O-Ring Kit 1-3/8” shft. B-N for 20HP
7,8,9,10,11 14-4436-00-K *Fastener Kit
Sleeve Kit 24-0172-79 Seal Sleeve Kit for 5HP thru 15HP (includes fi g. #’s 6,7,10,11,13)
Sleeve Kit 24-0172-95 Seal Sleeve Kit for 20HP (includes fi g. #’s 6,7,10,11,13)
12 22-0204-08-R Defl ector for 5HP thru 15HP22-0205-07-R Defl ector for 20HP
13 47-0022-09-02PK Sleeve O-Ring Kit 1 x 1-1/8 x 1/8 BN for 5HP thru 15HP (2 per kit)47-0126-04-02PK Sleeve O-Ring Kit 1-3/8 x 1-9/16 x 3/32 BN for 20HP (2 per kit)
14 47-0165-06-02PK O-Ring Kit 6-1/2 x 6-11/16 x 3/32 BN (2 per kit)
15 08-2908-01-R DB3 Wear Ring replacement
16 Motor See Motor Selection Page
Kit 24-0173-60 Mechanical Seal & O-Ring Kit 5HP to 15HP including #’s 5,6,13, & 14
Kit 24-0173-78 Mechanical Seal & O-RIng Kit for 20HP including #’s 5,6,13, & 14
*Fastener Kit #14443600K includes the following:1 each 3/8 - 16 x 3/4 HT/TR 410SS Hex Capscrews #7 for 5-15HP, 1 each 1/2 - 13 x 1-1/4 HT/TR 410 SS Hex Capscrews #7 for 20HP 4 each 3/8 - 16 x 1 PL Hex Capscrews #8, 4 each 3/8 - 16 x 1-1/8 PL Hex Capscrews #9 for 5-7.5HP4 each 1/2 - 13 x 1 PL Hex Capscrews #9 for 10-15HP, 4 each 1/2-13 x 2 PL Hex Capscrews #9 for 20HP1 each 3/16 x 1-1/8 303SS Square Key #10 for 5-15HP, 1 each 1/4 x 1-3/8 303SS Square Key #10 for 20HP1 each 1-1/8 x 13/32 x 1/8 Washer #11 for 5-15HP, 1 each Impeller Washer #11 for 20HP
Repair Parts
Model DC4Parts for Centrifugal Pumps
Mi8504
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
16
#15 Tube Kit
15
16
5
54
214 1310
3
2
14 13 10 8 7
11
6 117
18
789
6
4
Seal Sleeve Kit
Figure No. Part No. Description
102-0715-04-R Mtr. Bracket #11406 9-1/2” dia. for 20-25HP02-0716-03-R Mtr. Bracket #11407 13-1/2” dia. for 30-40-50HP
203-0867-09-R Case #11409 w/ plugs 4 x 4 NPT for 20-25-30HP03-0868-08-R Case #11421 w/ plugs 4 x 5 Flange for 40-50HP
3
05-3916-02-R Impeller #11422 @ 7-1/32” dia. for 20HP05-3917-01-R Impeller #11422 @ 7-15/32” dia. for 25HP05-3918-00-R Impeller #11422 @ 7-7/8” dia. for 30HP05-3919-09-R Impeller #11408 @ 8-7/16” dia. for 40HP05-3920-06-R Impeller #11408 @ 9-1/32” dia. for 50HP
4 08-2940-01-R Wear Ring 4.75 x 4.28 x 11/16
5 31-0059-11-06PK Plug Kit (6 per kit)
6 14-4437-09-K * Fastener Kit
7 13-0385-00-02PK O-Ring for spacer sleeve 1-3/8 shaft (2 per kit)
8 47-0126-04-02PK O-Ring Kit (2 per kit)
9 08-2897-04-R Seal Sleeve
Sleeve Kit 24-0172-95 Seal Sleeve Kit for 20HP thru 50HP including #’s 7,8,10,14, & 14
15 31-1691-05-K Poly Tube Kit 3/8 x 20”L w/connector #16
17 22-0205-07-R Defl ector 1-21/32” x 5-1/4” dia.
18 Motor See Motor Selection page
Kit 24-0173-78 Mech. Seal & Square & O-RIng Kit, 20 thru 50HP including #’s 7,8,11, & 12
*Fastener Kit #14443709K includes the following:12 each 1/2 - 13 x 1 PL Hex Capscrews #6, 12 each 20-25HP & 8 each for 30,40,50HP4 each 5/8 - 11 x 1-1/4 PL Hex Capscrews #6 for 30,40,50HP Motor side1 each 1/4 x 1-3/8 SS Square Key #101 each Washer #131 each 1/2 - 13 x 1-1/4 HT/TR 410SS Hex Capscrew #14
Repair Parts
Model HJM1 & HJM2Parts for Self-Priming Centrifugal Pumps
PAGE: RP-135DATE: June 5, 2006
12
8
9
10
4 5 6 7
4a
32
11
1
11
Figure No. Part No. Description1 31-0061-17-R Plug 1/2” NPT (incl. with case #2)
203-0387-00-K Case Kit #54360 w/ plugs & Wear-Ring 1-1/2”T for 1HP full rate & 1.5HP up-rate
Case Kit #54360 w/ plugs & Wear-Ring 2”T for 2HP full rate & 2.5HP up-rateCase Kit #54360 w/ plugs & Wear-Ring 2”T for 1.5HP full rate & 2HP up-rate
Impeller Kits include the following; Impeller, Diffuser, Mech-Seal, Wear-Ring & O-Ring Fig. #’s 3,4,4a,5,6,8,9
4
24-0173-03 Impeller Repair Kit for 1HJM1 -Brz Imp. #2794 @ 5”D - 9/16T24-0173-11 Impeller Repair Kit for 15HJM1 -Brz Imp. #2794 @ 5-17/32”D - 9/16T24-0173-29 Impeller Repair Kit for 2HJM1 -Brz Imp. #2794 @ 5”D - 9/16T
05-0776-15-RKIT Impeller Repair Kit SHJM1 - 3/4HP full rate & 1HP unity Plastic #2794 @4.75” - 7/16T05-2738-00-RKIT Impeller Repair Kit 1HJM1&2 - 1HP full rate & 1.5HP unity Plastic #2794 @5”D - 7/16T05-2727-03-RKIT Impeller Repair Kit HJM1 - 1.5HP full rate & 2HP unity Plastic #2794 @5.38”D - 7/16T05-3267-07-RKIT Impeller Repair Kit HJM1 - 2HP full rate & 2.5HP unity Brz. #4607 @5-13/16” - 7/16T
4A 08-0845-19-06PK Wear-Ring (6 ea. per kit)
5 10-1203-01 Mechanical Seal 3/4” for HJM110-1202-02 Mechanical Seal 5/8” for HJM2
6 47-0262-57-02PK Sq. Ring Kit 7x3/32 x .212 NTRL (2 ea. per kit)
7
02-1255-08-R Bracket for 1HP unity w/ fasteners 4-13/16 F #489502-1256-07-R Bracket for 1HP full rate & 1.5HP unity w/fasteners 5-1/16 F #489502-1272-07-R Bracket for 1.5HP full rate & 2 & 2.5HP unity w/fasteners 5-7/16 F #489502-1364-06-R Bracket for 1HP unity HJM2 4-13/16 F #111302-1362-08-R Bracket for 1HP full rate & 1.5HP unity HJM2 5-1/16 F #111302-1363-07-R Bracket for 1.5HP & 2HJM2 full rate & 2 & 2.5HP unity w/fasteners 5-7/16 F #1113
8, 9 14-4433-03-K *Fastener Kit
10 07-3610-09-R001 Coupling w/ Setscrews 9/16 thrd. for HJM1 Mtr. Shaft
11 31-0059-11-06PK Plug Kit 1/4” (6 ea. per kit)
12 Motor See Motor Selection Page
*Fastener Kit #14443303K includes the following:5 each 3/8 - 16 x 1-3/4 PL Hex Capscrews #8 4 each 3/8 - 16 x 3/4 PL Hex Capscrews #9 for HJM1 4 each 3/8 - 16 x 1 PL Hex Capscrews #9 for HJM2
Repair Parts
Models Typhoon, TY & TYCIParts for Self-Priming Centrifugal Pumps
Mi8505
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
23 4
1
7
64
Figure No. Part No. Description
1 31-1609-06-02PK Drain Plug Kit 1/4” with O-Ring for plastic unit (2 per kit)31-0059-11-06PK Drain Plug Kit 1/4” for cast iron unit (6 per kit)
2**03-0811-09-R Replacement case assy. KIT for plastic units built prior to 4/20/0503-0908-00-R Plastic Case w/plugs (for units built after 4/20/05)03-0045-06-R Cast Iron Case w/ plugs
Impeller Hydraulic Repair Kits include; Mech. Seal, Impeller, Eye Seal, Diffuser, Square-Ring, O-Ring
3
05-0341-03-RKIT Hydraulic Imp./Diff. Repair kit for 7TY & S10TY #03412 @ 5.13D x .105P05-0342-02-RKIT Hydraulic Imp./Diff. Repair kit for 10TY & S15TY #03423 @ 5.13D x .145P05-0344-00-RKIT Hydraulic Imp./Diff. Repair kit for 15TY & S20TY #03444 @ 5.13D x .165P05-0340-01-RKIT Hydraulic Imp./Diff. Repair kit for 20TY & S25TY #03401 @ 5.13D x .235P
4 11-0012-03-R Seal Plate Assy. Cast Iron w/ studs, washers & nuts**11-0060-04-R Plastic Seal Plate (discontinued on plastic units built after 4/20/05)
5 14-4447-07-K Fastener Kit for Plastic Case14-11295-06-K Fastener Kit for Cast Iron Case
6
9010-1327-R Motor 3/4HP - 115/230/1/60 56Z full service & 1HP unity service9010-1331-R Motor 1HP - 115/230/1/60 56Z full service & 1.5HP unity service9010-1345-R Motor 1.5HP - 115/230/1/60 56Z full service & 2.5HP unity service9010-1352-R Motor 2HP - 115/230/1/60 56Z full service & 1HP unity service
7 12-1144-01-R Base Assembly Kit w/fasteners and protector for 3/4, 1, 1.5HP full service 48Fr. Mtr.12-1145-00-R Base Assembly Kit w/fasteners and protector for 2HP full service 56Fr. Mtr.
*Note; The following plastic parts used on units prior to 4/20/05 have been discontinued and the new Case Kit #03081109R000 replaces them; 11006004R, 11006004R, 42372300R, 03081109R.
Repair Parts
Model H4Parts for Booster Pumps
PAGE: RP-140DATE: June 5, 2006
15 12 11
1317
1819
35
2420
16
14 23 2221
1634
10 98
37
36
7
6 31
5
1
33
4
123
#4 Shaft Cplg. Kit
Figure No. Part No. Description1 Motor See Motor Selection page
3 23-2649-06-R Piston Cup 5/8 x 3/8 x 3/32 (also included with #4 kit & #38 24-0175-19 kit)
4 07-9035-03-RKIT Shaft Coupling Kit w/ #5 setscrews, #12 spacers, #3 cup
*5,6 14-4439-07-K *Fastener Kit
7 03-0770-05-R Bracket w/ fasteners #6 C.I. #11242
8 10-1203-01 Mechanical Seal 3/4” (also incl. #38 component kit)
*9,10,11,12 See #38 H4 Booster Component Kit
13 Shaft Consult the factory for size and availability
14
04-5330-06-R 5 GPM Stage Assembly 3/8” Shft.04-5329-09-R 10 GPM Stage Assembly 3/8” Shft.04-5621-04-R 18 GPM Stage Assembly 3/8” Shft.04-5505-05-R 25 GPM Stage Assembly 3/8” Shft.
15 Shell Consult the factory for size and availability
16 47-0235-02-06PK O-Ring Kit (6ea. per kit) - (also incl. in kit #38)
17,18,19 See #38 H4 Booster Component Kit
20 04-5461-07-R Discharge Housing w/ rubber bearings and plugs
21 Studs Consult the factory for size and availability (3 ea. req’d)
22,23 See #38 H4 Booster Component Kit
24 31-0059-11-06PK Plug Kit 1/4’ Galv. (6 ea. per kit)
31 12-1033-05-R Motor Handle for 1/3HP & 1/2HP only
33 23-4857-09-R Motor Cord
34 30-0274-03-R Screen
35 16-1065-02-R Air Valve 1/8” NPT (also included in #38 kit)
36 08-2323-02-R Intermediate support w/ brg. (H425-27M only)
37 08-2888-03-R Hub Sleeve 2 ea. required (H425-27M only)
38 24-0175-19 H4 Booster Component Kit includes; 8,9,10,11,12,16,17,18,19,22,23,35
*Fastener Kit includes the following:2 each 5/16 - 18 x 3/8 Socket set screws #54 each 3/8 - 16 x 7/8 PL Hex Capscrews #6 1 each #9,10,11,18,19 & 3 each #22,23
Mi8506
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Repair Parts
Model Vertical (50-75GPM)Parts for Booster Pumps
PAGE: RP-145DATE: June 5, 2006
17
31
15
11
24
25
22
34
33
7
15
31
17
18
13
35
20
11
24
25
5
8
32
16
9 & 102,3 &4
32
16
9 & 102,3 &4
22
1
26
20
19
35
13
14
17
21
12
19
36 (Module)
Repair Parts
Model Vertical (50-75GPM)Parts for Booster Pumps
Mi8507
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Figure No. Part No. Description1 Motor See Motor Selection Page
2 77-0759-01-R Motor Coupling 56C / 140TC w/ 5/16 setscrews
3 77-0760-08-R Motor Coupling 180TC 1-1/2”B w/ 3/8 setscrews
4 77-0761-07-R Motor Coupling 210TC w/3/8-16 x 1/2 setscrews
5 04-5594-07-R Motor Bracket #11405
6,7 14-4440-04K *Fastener Kit
8 08-2938-05-R Sleeve 5/8” x 7/8” x 1-5/8”
9,10,11 14-4440-04K *Fastener Kit
12,13,14 Tie Rods, Shaft, Shell, - Consult factory for size and availability
15 08-2912-05-R Ceramic Sleeve (5 each required) 1 x 5/8 Hex.
16,17 14-4440-04K *Fastener Kit
18 08-2771-05-R Rubber Bearing
19 47-0247-08-02PK O-Ring Kit (2 per kit) 4-5/8 x 4-7/8 x 1/8 BN
20 08-2772-04-R Spacer V650 - V675
21 14-4440-04K *Fastener Kit
22 10-0369-03 Mechanical Seal 150PSI 1-1/4”10-0470-01 Mechanical Seal 400PSI 1-1/4”
23 04-5595-06-R VB6 Base 2” NPT #11404
24 14-4440-04K *Fastener Kit
25 47-0113-09-02PK O-Ring Kit 9/16 x 3/4 x 3/32 (2 per kit)
26 11-1514-04-R Motor adpt. Flg. 180TC thru 210TC frame w/ fasteners #11414
27 14-4440-04K Hex Cap. Kit 1/2-13x1 4 ea. req’d (24 per kit)
28 31-0059-11-06PK Plug Kit 1/4” (6 per kit)
29 31-0061-17-R Plug 1/2”
31 14-4277-02-R Washer 1 x 7/16 x .105
32 14-4440-04K *Fastener Kit
33 11-1515-03-R Seal Plate
34 47-0138-59-02PK Square-Ring Kit 2-1/8 x 3/32 x 3/32 BN (2 per kit)
3504-5646-05-R Stage Assembly V65004-5649-02-R Stage Assembly V67522-5764-09 V6 End-play Tool
36
9132-4517 VB650 1.5HP 2 Stages9132-4525 VB650 2HP 3 Stages9132-4533 VB650 3HP 4 Stages9132-4541 VB650 5HP 7 Stages9132-4566 VB650 7.5HP 10 Stages9132-4582 VB675 3HP 2 Stages9132-4590 VB675 5HP 4 Stages9132-4616 VB675 7.5HP 6 Stages
*Fastener Kit #14444004K includes the following;4 each 3/8 - 16 x 1 PL Hex Capscrews #6 4 each 1/4 - 20 x 1/2 SS Hex Capscrews #7 3 each 3/8 - 16 x 1/2 Set Screws #93 each 5/16 - 18 x 1/2 Set Screws #10 1 each 5/8 Washer SS #116 each 3/8 - 16 PL Hex Nut #174 each 3/8 Lockwashers #211 each Washer 13/16 x 21/64 x 1/4 SS #164 each 1/2-13 x 1 PL Hex Capscrews #271 each Retainer Ring #241 each 5/16-24 x 1 Capscrew #32
Repair Parts
All ModelsParts for Gas Powered Pumps
PAGE: RP-150DATE: June 5, 2006
Mi8508
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
Fig. No. Part No. Description1 03-0902-06-R Case Assembly w/valve (LSA)
2 9198-7768-R Check Valve Assembly (LSA)
3 10-1529-08-R Shaft Seal and O-Ring (LSA)
4 05-0369-00-R Impeller 3HP (not available)05-0370-07-R Impeller 5HP (not available)
5 12-1150-02-R Handle w/fasteners (not available)
6 08-2959-09-R Shaft Sleeve, Slinger, and Seal (LSA)
7 02-1706-03-R Motor Bracket (not available)
8 03-0903-05-R Strainer (LSA)
9 12-1151-01-R Base w/fasteners (not available)
10 9010-9307-R Engine, 3HP (not available)9010-9505-R Engine, 5HP (not available)
2
1
3
5
9
10
6
8
7
Note: These Models discontinued year 2004 Limited stock available on some items (LSA)
Repair Parts
Model A & RSPAParts for End Suction “SPA” Pumps
PAGE: RP-155DATE: June 5, 2006
8
7
12
3
4
56
Figure No. Part No. Description1 02-1684-09-R Bracket for Spa Pump
2 10-0002-06 Mechanical Shaft Seal 5/8
3
05-1500-15-R Impeller 3.875 dia. x .390P #11433 for S2A, R20SPA05-2000-20-R Impeller 3.875 dia. x .565P #11434 for S35A, R35SPA05-2000-25-R Impeller 3.875 dia. x .582P #11434 for S3A05-3000-30-R Impeller 3.875 dia. x .692P #11435 for S4A05-0365-04-K Impeller Kit 4.20 dia. x .81P for S45A, R45SPA (incl. #2,3,4)
4 47-0258-53-R Square-Ring 6-1/8 x 1/8 nitrl.
5 03-0872-03-R Case Assembly with plugs03-0889-03-R Case Assembly Kit with plugs for model S45A, R45SPA
6 31-1609-06-02PK 1/4’ Plug Ki w/ O-Ring (2 per kit)
7 14-4379-02-R Screws 10-12 x 1 phil/pan hd. SS
8
9010-1288-R S2A Motor 2HP 115/230 - 1/60 48Fr. 1.0SF9010-6816-R S3A Motor 3HP 230/1/60 48Fr. 1.0SF9010-6592-R S35A Motor 3.5HP 230/1/60 48Fr. 1.0SF9010-3367-R S4A Motor 4HP 230/1/60 48Fr. 1.0SF9010-6600-R S45A Motor 34.5HP 230/1/60 48Fr. 1.0SF
Repair Parts
Model J, K, JCM, SKM, RJTJ, THTM & RSPAParts for Jetted Tub & SPA Pumps
Mi8509
400 East Spring Street, Bluffton, IN 46714Tel: 260.824.2900 Fax: 260.824.2909 www.franklinpumps.com
8 7a
7
36
5
4
2
1
Figure No. Part No. Description
19010-1197 Motor 3/4HP 115/1/60 48Fr. 1.0SF
9010-6543-R Motor 1HP 115/1/60 48Fr. 1.0SF9010-1288-R Motor 1.5HP 115/1/60 48Fr. 1.0SF
202-1308-05-RKIT J Bracket Kit (incl. #7 3-10 butt & #8 1/4-14 x 1-1/8 fasteners)
02-1309-04-R JCM & SKM Bracket (eff. 2/1/94) 1/4-14 Thrd, 2-1/2 butt.02-1613-05-R JCM & SKM Bracket (eff. prior 2/1/94) 1/4-20 Thrd, 2-1/2 butt. w/fasteners
3 47-0357-46-R O-Ring 5-1/2 x 5-7/8 x 3/16
4 10-0002-06 5/8 Mechanical Seal
5
05-3862-06-R Impeller S7J, S7K #11343 3.45D05-3863-05-R Impeller S1J, S1K #11343 3.73D05-3864-04-R Impeller S15J, S15K #11343 4.10D05-3865-03-R Impeller S2J, S2K #11304 4.22D
6 10-1462-07-R Eye Seal
7 03-0651-09-R J Flange 3-10 butt03-0854-04-R JCM Flange 2-1/21-8 butt
7A 11-1517-01-R SKM Flange 2-1/2” butt with 1/4’ plug 31160906R
814-1266-35-R** Fastener 1/4-20x3/4 4 required, Eff. for units prior to 2/1/94 “J” Model14-4339-08-R J, JC, SK, RJT - Fastener 1/4-14 x 1-1/8 Hex. Wash.
31-1756-08 S15UNS Halves (2)** Discontinued, no longer available.
Warranty
PAGE: WR-100DATE: June 5, 2006
Lost or Damaged GoodsInformation
Mi8600
IMPORTANTEvery carrier used by Franklin Pump Systems, Inc. is required to verify and sign for the condition of and the number of pieces that are released to them for delivery. Our control and responsibility for any shipment ceases when the carrier signs the Bill of Lading. When you sign the Bill of Lading, you legally assume responsibility of the shipment being delivered. Please, thoroughly inspect each shipment immediately upon arrival.
If cartons, packages, or crates are received in short or damaged condition, it is important that you notify the driver and insist on a notation of the loss or damage across the face of the freight bill. Failure to do this could negate any opportunity you have to fi le a claim. Claims for short or damaged material must be fi led in writing with the carrier immediately after delivery.
If concealed loss or damage is discovered, notify the carrier at once and request an inspection. It is also important that you do not discard the shipping carton or container. A concealed damage report should be made within ten (10) days of delivery of the shipment. The carrier’s agent will make an inspection and usually will grant a concealed damage notation. If you give the carrier a clear receipt for the goods that have been damaged in transit, you do so at your own risk and expense.
We are willing to assist you to collect claims for loss or damage, but we are not responsible for collection of claims or replacement of material (shortage or damage) if not noted on the Bill of Lading at the time of delivery.
Due to frequent damage of heavy UPS shipments, Franklin Pump Systems, Inc. does not ship orders over 75 lbs. by UPS unless customer agrees to take full responsibility.
For information or assistance contact:
Customer Service Departmentp: 501.455.1234 www.franklin-electric.com
Warranty
PAGE: WR-105DATE: June 5, 2006
Mi8601
U.S. LIMITED WARRANTY*
Franklin Pump Systems, Inc.
Franklin Pump Systems, Inc. warrants its new products to be free of defects in material and workmanship for a period of 1 year from date of installation or 2 years from date of manufacture, whichever comes fi rst, WHEN installed in a domestic water systems application and pumping potable water only. Warranty does not cover applications pumping saltwater or other corrosive liquids. Consult and adhere to local codes for all applications.
Franklin Pump System’s warranty obligation with regard to equipment not of its own manufacture is limited to the warranty actually extended to Franklin Pump System by its suppliers.
This warranty extends only to the original retail purchaser and only during the time in which the original retail purchaser occupies the site where the product was originally installed.
Requests for service under this warranty shall be made by contacting the installing Franklin Pump System dealer (point of purchase) as soon as possible after the discovery of any alleged defect. Franklin Pump System will subsequently take corrective action as promptly as reasonably possible.
Franklin Pump System at its discretion may replace or repair any product that fails under this warranty after inspection by an authorized company representative or after Franklin Pump System has received the product at our factory. Replacement or repair cannot be made until after the product is inspected. All charges or expenses for freight to and from the factory, removal and reinstallation of the product, or installation of a replacement product are the responsibility of the purchaser.
THIS WARRANTY SUPERSEDES ANY WARRANTY NOT DATED OR BEARING AN EARLIER DATE. ANY IMPLIED WARRANTIES WHICH THE PURCHASER MAY HAVE, INCLUDING MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE APPLICABLE WARRANTY PERIOD. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL FRANKLIN PUMP SYSTEM BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This warranty does not apply to any product which has been subjected to negligence, alteration, accident, abuse, misuse, improper installation, vandalism, civil disturbances, or acts of God. The only warranties authorized by Franklin Pump System are those set forth herein. Franklin Pump System does not authorize other persons to extend any warranties with respect to its products, nor will Franklin Pump System assume liability for any unauthorized warranties made in connection with the sale of its products.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
* Contact Franklin Pump Systems, Inc. Export Division for International Warranty.
12401 Interstate 30 • P.O. Box 8903
Little Rock, AR 72219