01-2 dynamic configuration (bsc).pdf

7/28/2019 01-2 Dynamic Configuration (BSC).pdf

1/87

M900/M1800 Base Station Controller Data Configuration Manual - Dynamic Configuration Contents

Issue 08 (2006-08-20) Huawei Technologies Proprietary i

Contents

2 BSC Data Configuration...........................................................................................................2-1

2.1 Modifying the BIE Visibility.........................................................................................................................2-3

2.1.1 Task Description .................................................................... .............................................................. 2-3

2.1.2 Procedure ............................................................ ................................................................. ................2-3

2.1.3 Verification...........................................................................................................................................2-5

2.1.4 Data Table .......................................................... .................................................................. ................2-5

2.2 Modifying the GLAP Visibility.....................................................................................................................2-6


2.2.2 Procedure ............................................................ ................................................................. ................2-6

2.2.3 Verification...........................................................................................................................................2-8

2.2.4 Data Table .......................................................... .................................................................. ................2-8

2.3 Modifying the Phase Flag of the BSC Interface............................................................................................2-9


2.3.2 Procedure ............................................................ ................................................................. ................2-9

2.3.3 Verification.........................................................................................................................................2-10

2.3.4 Data Table .......................................................... .................................................................... ............2-10

2.4 Modifying the Local Advanced Property ................................................................ .................................... 2-11

2.4.1 Task Description .................................................................... ............................................................ 2-11 2.4.2 Procedure ............................................................ ................................................................. .............. 2-11

2.4.3 Verification.........................................................................................................................................2-12

2.4.4 Data Table .......................................................... .................................................................... ............2-12

2.5 Modifying the Voice Optimization Parameter............................................................. ................................2-12

2.5.1 Task Description .................................................................... ............................................................ 2-12

2.5.2 Procedure ............................................................ ................................................................... ............2-12

2.5.3 Verification.........................................................................................................................................2-14

2.5.4 Data Table .......................................................... .................................................................... ............2-14


2/87

ContentsM900/M1800 Base Station Controller

Data Configuration Manual - Dynamic Configuration

ii Huawei Technologies Proprietary Issue 08 (2006-08-20)

2.6 Modifying the CRC4 Check of the BSC Transparent Transmission BIE................................ ....................2-14


2.6.2 Procedure ............................................................ ................................................................... ............2-14

2.6.3 Verification.........................................................................................................................................2-15

2.6.4 Data Table .......................................................... .................................................................... ............2-15

2.7 Configuring Monitor Timeslots...................................................................................................................2-16


2.7.2 Procedure ............................................................ ................................................................... ............2-16

2.7.3 Verification.........................................................................................................................................2-22

2.7.4 Data Table .......................................................... .................................................................... ............2-22

2.8 Modifying the Abis Bypass Switch.............................................................................................................2-23


2.8.2 Procedure ............................................................ ................................................................... ............2-23

2.8.3 Verification.........................................................................................................................................2-26

2.8.4 Data Table .......................................................... .................................................................... ............2-26

2.9 Dynamic Configuration Without Command .......................................................... ..................................... 2-27

2.9.1 Configuring Trunk Circuits................................................................................................................2-28

2.9.2 Configuring the BTS Software Index .................................................................. ..............................2-32

2.9.3 Configuring Flow Control Parameters ....................................................................... ........................2-35

2.9.4 Configuring Common Parameters......................................................................................................2-37

2.9.5 Configuring Semi-Permanent Connection ...................................................................... ...................2-41

2.9.6 Configuring Alarm Parameters ................................................................ .......................................... 2-43

2.9.7 Configuring the GMEM.....................................................................................................................2-45

2.9.8 Configuring Board Software Loading................................................................................................2-48

2.9.9 Configuring Timer Data.....................................................................................................................2-50

2.9.10 Modifying the Module Description Table ....................................................................... .................2-52 2.10 Importing Network Parameters .................................................................. ............................................... 2-54

2.10.1 Task Description ............................................................. ................................................................. 2-54

2.10.2 Procedure ............................................................... ........................................................................ ..2-54

2.10.3 Verification.......................................................................................................................................2-55

2.11 Exporting Network Parameters .................................................................. ............................................... 2-56

2.11.1 Task Description...............................................................................................................................2-56

2.11.2 Procedure ............................................................... .......................................................................... 2-56


3/87

M900/M1800 Base Station Controller Data Configuration Manual - Dynamic Configuration Contents

Issue 08 (2006-08-20) Huawei Technologies Proprietary iii

2.11.3 Verification.......................................................................................................................................2-57

2.12 Modifying Reserved Parameters ................................................................. .............................................. 2-58


2.12.2 Procedure ............................................................... ........................................................................ ..2-58

2.12.3 Verification.......................................................................................................................................2-61

2.12.4 Data Table ............................................................. ......................................................................... ..2-61

2.13 Configuring the SS7 Property ........................................................................ ........................................... 2-61


2.13.2 Procedure ............................................................... ........................................................................ ..2-62

2.13.3 Verification.......................................................................................................................................2-64

2.13.4 Data Table ............................................................. ......................................................................... ..2-64

2.14 Modifying the PB Interface Property ..................................................................... ................................... 2-64


2.14.2 Procedure ............................................................... ........................................................................ ..2-65

2.14.3 Verification.......................................................................................................................................2-65

2.14.4 Data Table ............................................................. ......................................................................... ..2-65

2.15 Modifying the BIE Trunk Mode................................................................................................................2-66


2.15.2 Procedure ............................................................... ........................................................................ ..2-66

2.15.3 Verification.......................................................................................................................................2-70

2.15.4 Data Table ............................................................. ......................................................................... ..2-70

2.16 Moving a Site ............................................................ ................................................................... .............2-72


2.16.2 Procedure ............................................................... ........................................................................ ..2-72

2.16.3 Verification.......................................................................................................................................2-76

2.16.4 Data Table ............................................................. ......................................................................... ..2-76


4/87

M900/M1800 Base Station Controller Data Configuration Manual - Dynamic Configuration Figures

Issue 08 (2006-08-20) Huawei Technologies Proprietary v

Figures

Figure 2-1 Selecting a module and board...........................................................................................................2-3

Figure 2-2 Command list for dynamic configuration ..................................................................... ....................2-4

Figure 2-3 Dynamic configuration command.....................................................................................................2-5

Figure 2-4 Selecting a GLAP ..................................................................... ........................................................ 2-7

Figure 2-5 Command list for dynamic configuration ..................................................................... ....................2-8

Figure 2-6 Configuring the property of each BSC interface ...................................................................... ........2-9

Figure 2-7 Command list for dynamic configuration ...................................................................... .................2-10

Figure 2-8 Modifying the local advanced property ......................................................................... ................. 2-11

Figure 2-9 Modifying the voice optimization parameter..................................................................................2-13

Figure 2-10 Command list for dynamic configuration ....................................................................... ..............2-13

Figure 2-11 Selecting the transparent transmission BIE...................................................................................2-15

Figure 2-12 Selecting a BIE board ........................................................... ........................................................ 2-17

Figure 2-13 Selecting a BIE port......................................................................................................................2-18

Figure 2-14 Configuring the monitor timeslot .................................................................... .............................2-18

Figure 2-15 Information prompt.......................................................................................................................2-19


Figure 2-17 Selecting a BIE port and site.........................................................................................................2-20

Figure 2-18 Configuring the site monitor timeslot...........................................................................................2-21

Figure 2-19 Setting the end channel number....................................................................................................2-22



5/87


6/87

M900/M1800 Base Station Controller Data Configuration Manual - Dynamic Configuration Figures

Issue 08 (2006-08-20) Huawei Technologies Proprietary vii

Figure 2-47 Timer data.....................................................................................................................................2-51

Figure 2-48 Dynamic configuration without command .................................................................. .................2-53

Figure 2-49 Module description table .............................................................. ................................................ 2-53

Figure 2-50 Selecting the text file ...................................................................... .............................................. 2-55


Figure 2-52 Exporting network parameters......................................................................................................2-56

Figure 2-53 Saving the text file........................................................................................................................2-57


Figure 2-55 Selecting TRXs.............................................................................................................................2-59

Figure 2-56 Selecting a module........................................................................................................................2-59

Figure 2-57 Modifying the reserved parameters ................................................................. .............................2-60

Figure 2-58 Reserved Parameters Configuration dialog box............................................................................ 2-60

Figure 2-59 Confirmation prompt ................................................................ .................................................... 2-62

Figure 2-60 Configuring the SS7 property.......................................................................................................2-62

Figure 2-61 Configuring the E3M board property ................................................................. ..........................2-63

Figure 2-62 Modifying PB Interface Property..................................................................................................2-65

Figure 2-63 Selecting a BIE ............................................................ ................................................................. 2-67

Figure 2-64 Modifying the BIE trunk mode.....................................................................................................2-67


Figure 2-66 Adjusting the BIE property...........................................................................................................2-68

Figure 2-67 Manual site list..............................................................................................................................2-69


Figure 2-69 Selecting a site .................................................................... .......................................................... 2-73

Figure 2-70 Moving the site .............................................................. ............................................................... 2-74


Figure 2-72 Moved sites and cell list................................................................................................................2-75


7/87

FiguresM900/M1800 Base Station Controller


viii Huawei Technologies Proprietary Issue 08 (2006-08-20)

Figure 2-73 Adjusting site TRX information....................................................................................................2-75

Figure 2-74 Adjusting the BIE port ................................................................. ................................................. 2-76


8/87

M900/M1800 Base Station Controller Data Configuration Manual - Dynamic Configuration Tables

Issue 08 (2006-08-20) Huawei Technologies Proprietary ix

Tables

Table 2-1 Data table modified during the modification of the BIE visibility ..................................................... 2-5

Table 2-2 Data table modified during the modification of the GLAP visibility ................................................. 2-8

Table 2-3 Data table modified during the modification of the phase flag of the BSC interface ....................... 2-10

Table 2-4 Data table modified during the modification of the local advanced property...................................2-12

Table 2-5 Data table modified during the modification of the voice optimization parameter .......................... 2-14

Table 2-6 Data tables modified during the modification of the CRC4 check of a transparent transmission BIE.2-16

Table 2-7 Data tables modified during the modification of monitor timeslots ................................................. 2-22

Table 2-8 Data tables modified during the modification of the Abis bypass switch......................................... 2-26

Table 2-9 Data tables modified during the modification of trunk circuits ........................................................ 2-32

Table 2-10 Data table modified during the modification of the BTS software index....................................... 2-35

Table 2-11 Data table modified during the modification of the flow control parameters ................................. 2-37

Table 2-12 Meaning of the software parameters...............................................................................................2-39

Table 2-13 Data tables modified during the modification of common parameters...........................................2-40

Table 2-14 Data table modified during the modification of semi-permanent connection................................. 2-43

Table 2-15 Data tables modified during the modification of alarm parameters................................................2-45

Table 2-16 Data table modified during the modification of the IP address of the GMEM............................... 2-48

Table 2-17 Data table modified during the modification of the loading information of board software ..........2-50

Table 2-18 Data table modified during the modification of timer data.............................................................2-52

Table 2-19 Data table modified during the modification of the module description ........................................ 2-54


9/87

TablesM900/M1800 Base Station Controller


x Huawei Technologies Proprietary Issue 08 (2006-08-20)

Table 2-20 Data tables modified during the modification of the reserved parameters ..................................... 2-61

Table 2-21 Data tables modified during the modification of the SS7 property ................................................ 2-64

Table 2-22 Data table modified during the modification of the property of the PB interface ..........................2-66

Table 2-23 Data tables modified during the modification of the BIE trunk mode............................................2-70

Table 2-24 Modified data tables during site movement....................................................................................2-77


10/87

M900/M1800 Base Station Controller Data Configuration Manual - Dynamic Configuration 2 BSC Data Configuration

Issue 08 (2006-08-20) Huawei Technologies Proprietary 2-1

2 BSC Data ConfigurationAbout This Chapter

The following table lists the contents of this chapter.

Title Description

2.1 Modifying the BIEVisibility

Describes how to modify the BIE visibility.

2.2 Modifying the GLAPVisibility

Describes how to modify the GLAP visibility.

2.3 Modifying the Phase Flagof the BSC Interface

Describes how to modify the phase flag of the BSCinterface.

2.4 Modifying the LocalAdvanced Property

Describes how to modify the local advanced property.

2.5 Modifying the VoiceOptimization Parameter

Describes how to modify the voice optimize parameter.

2.6 Modifying the CRC4Check of the BSC TransparentTransmission BIE

Describes how to modify the BSC transparenttransmission BIE CRC4 check.

2.7 Configuring Monitor Timeslots

Describes how to configure monitor timeslots.

2.8 Modifying the AbisBypass Switch

Describes how to modify the Abis bypass switch.

2.9 Dynamic ConfigurationWithout Command

Describes the dynamic configuration without command.

2.10 Importing Network

Parameters

Describes how to import network parameters.


11/87

2 BSC Data ConfigurationM900/M1800 Base Station Controller


2-2 Huawei Technologies Proprietary Issue 08 (2006-08-20)

Title Description

2.11 Exporting Network Parameters

Describes how to export network parameters.

2.12 Modifying ReservedParameters

Describes how to modify reserved parameters.

2.13 Configuring the SS7Property

Describes how to configure the SS7 property.

2.14 Modifying the PBInterface Property

Describes how to modify the PB interface property.

2.15 Modifying the BIE Trunk Mode

Describes how to modify the BIE trunk mode.

2.16 Moving a Site Describes how to move a site.


12/87



2.1 Modifying the BIE Visibility

2.1.1 Task Description

Purpose To modify the visibility of a BIE

Prerequisite The BIE is configured on the BSC Data Auto Configuration System.

Note

z The boards not configured with hardware are invisible and cannot bedeleted. You can only add sites to the visible BIE.

z You can modify the visibility of more than one BIE in a module in oneoperation. In a multi-module BSC, the transparent transmission BIEcannot be set to invisible.

2.1.2 Procedure

This part uses an example to show how to modify the visibility of BIEs. Assume that youhave to set the BIEs numbered 4 and 5 in BM1 to visible, and the ones numbered 7, 8 and 9 toinvisible.

The procedure is as follows:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify BIE Visibility .

The Modify BIE Visibility dialog box as shown in Figure 2-1 is displayed.

Figure 2-1 Selecting a module and board


13/87




In the Modify BIE Visibility dialog box, except for the transparent transmission BIE, no other BIEconnects to any site. Do not set a transparent transmission BIE to invisible.

You can press Ctrl or Shift to select more than one BIE.

Step 2 Select Module 1 from the Select Module drop-down list.

Step 3 Select No.4 BIE Board, Invisible , No.5 BIE Board, Invisible , No.7 BIE Board, Visible , No.8 BIE Board, Visible , and No.9 BIE Board, Visible from the Select BIE box.

Step 4 Click Next .

The Modify BIE Visibility dialog box is refreshed, as shown in Figure 2-2 .

Figure 2-2 Command list for dynamic configuration

Step 5 Click Browse Command Table .

The Dynamic Configuration Command Word's Parameter Table dialog box as shown inFigure 2-3 is displayed.


14/87


15/87




The modified data tables in the BSC Data Management System list all the data tables related to thedynamic configuration. These data tables are refreshed and set to the GMPU during the dynamicconfiguration.

Hereafter, modified data tables have the same meaning as that explained here.

2.2 Modifying the GLAP Visibility


Purpose To display or hide the GLAP

Prerequisite The GLAP is configured on the BSC Data Auto Configuration System.

Note

z The LAPD links can be assigned to only a visible GLAP.

z You can change the visibility of more than one GLAP in a module inone operation.

2.2.2 Procedure

This part uses an example to show how to modify the visibility of the GLAP. Assume that you

have to set the GLAP numbered 6 in BM1 to invisible and the one numbered 7 to visible.


Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify GLAP Visibility .

The Modify GLAP Visibility dialog box as shown in Figure 2-4 is displayed.


16/87



You can press Ctrl or Shift to select more than one GLAP.

Figure 2-4 Selecting a GLAP

The GLAPs in the Modify GLAP Visibility dialog box as shown in Figure 2-4 are out of service. Nosignaling link is assigned to these GLAPs.


Step 3 Select No.6 GLAP Board, Visible and No.7 GLAP Board, Invisible from the Select GLAP box.

Step 4 Click Next .

The Modify GLAP Visibility dialog box is refreshed, as shown in Figure 2-5 .


17/87





Step 5 Click Start Dynamic Configuration to activate the data.

----End

2.2.3 Verification

Check the status of the GLAP on the BSC Maintenance System.

2.2.4 Data Table

Table 2-2 lists the modified data table in the BSC Data Management System.

Table 2-2 Data table modified during the modification of the GLAP visibility

No. Table Name

1 Slot Description Table


18/87



2.3 Modifying the Phase Flag of the BSC Interface


Purpose z To modify the GSM protocol standards used by the BSC interfacesz To modify the locating service (Cell ID+TA) status and the inter system

HO status

Prerequisite None

Note None

2.3.2 ProcedureThis part uses an example to show how to modify the phase flag of the BSC interface.Assume that you have to change the version of the Abis interface into GSM_Phase_2.


Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify BSC Interface PhaseFlag .

The Modify BSC Interface Phase Flag dialog box as shown in Figure 2-6 is displayed.

Figure 2-6 Configuring the property of each BSC interface

Step 2 Select GSM_Phase_2 from the Abis Interface Version drop-down list.


19/87




Step 3 Click Next .

The Modify BSC Interface Phase Flag dialog box is refreshed, as shown in Figure 2-7 .



----End

2.3.3 Verification

After changing the BSC interface phase flag, check that:

z The related data in the Local Office Information Table are correctly modified.

To view the Local Office Information Table, choose Task > Data Management >Local-office > Local Office Information Table .

z The related host data are set to each module of the BSC.

To view the host data, choose Task > Data Management > Operations > View HostData .

2.3.4 Data Table


Table 2-3 Data table modified during the modification of the phase flag of the BSC interface

No. Table Name

1 Local Office Information Table


20/87



2.4 Modifying the Local Advanced Property2.4.1 Task Description

Purpose To modify the local advanced properties

Prerequisite None

Note None

2.4.2 Procedure

To change the advanced properties, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify Local AdvancedProperty .

The Modify Local Advanced Property dialog box as shown in Figure 2-8 is displayed.

Figure 2-8 Modifying the local advanced property

Step 2 Set the values in the OWA Check Time text box and the GPRS Suspend Timer Value(s)

text box.


21/87




Step 3 Click Next .


----End

2.4.3 Verification

After changing the advanced property, check that:

z The related data in the Local Office Information Table are correctly modified.


2.4.4 Data TableTable 2-4 lists the modified data table in the BSC Data Management System.

Table 2-4 Data table modified during the modification of the local advanced property

No. Table Name


2.5 Modifying the Voice Optimization Parameter


Purpose To modify the voice encoding and decoding of the BSC

Prerequisite None

Note None

2.5.2 Procedure

To change the voice encoding and decoding of the BSC, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify Voice OptimizeParameter .


22/87



The Modify Voice Optimization Parameter dialog box as shown in Figure 2-9 is displayed.

Figure 2-9 Modifying the voice optimization parameter

Step 2 Select Normal Encode/Decode from the Voice Encode/Decode Optimization drop-downlist.

Step 3 Click Next .

The Modify Voice Optimization Parameter dialog box is refreshed, as shown in Figure 2-10 .



----End


23/87




2.5.3 Verification

After changing the voice optimization parameter, check that:

z The related data in the Local Office Information Table are correctly modified.z The related host data are set to each module of the BSC.

2.5.4 Data Table


Table 2-5 Data table modified during the modification of the voice optimization parameter

No. Table Name


2.6 Modifying the CRC4 Check of the BSC TransparentTransmission BIE

2.6.1 Task DescriptionPurpose To modify the CRC4 check of a transparent transmission BIE

Prerequisite None

Note You can change the CRC4 check values of all the transparent transmissionBIE in one operation.

2.6.2 ProcedureThis part uses an example to show how to change the CRC4 check of a transparenttransmission BIE. Assume that you have to change the value of transparent transmission BIECRC4 of BM1 into 110011, and that of BM2 into 001100.


Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify BSC TransparentTransmission BIE CRC4 Check .


24/87



The Modify BSC Transparent Transmission BIE CRC4 Check dialog box as shown inFigure 2-11 is displayed.

Figure 2-11 Selecting the transparent transmission BIE

Step 2 Select the transparent transmission BIE of Module[1] . Then select Port 0 , Port 1 , Port 4 , andPort 5 from the CRC4 Check list box. The BIE CRC4 value becomes 110011.

Step 3 Select the transparent transmission BIE of Module[2] . Then select Port 2 and Port 3 from theCRC4 Check list box. The BIE CRC4 value becomes 001100.

Step 4 Click Next .


----End

2.6.3 Verification

After modifying the CRC4 check of a transparent transmission BIE, check that:

z The related data in the data tables are correctly modified.

z The related data are correctly configured to each module of the host.

2.6.4 Data Table

Table 2-6 lists the modified data tables in the BSC Data Management System.


25/87




Table 2-6 Data tables modified during the modification of the CRC4 check of a transparenttransmission BIE

No. Table Name

1 BSC BIE Description Table2 BSC BIE Active/Stby. Group Table

2.7 Configuring Monitor Timeslots


Purpose To configure monitor timeslots

Prerequisite None

Note

You can configure monitor timeslots in two modes: auto calculate modeand manual mode.

If the site is in manual adjustment mode, use the manual mode. Otherwiseuse the auto calculate mode.

2.7.2 Procedure

Procedure for Manual Configuration

To configure the monitor timeslot in manual mode, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Configure Monitor Timeslot .

The Configure Monitor Timeslot dialog box as shown in Figure 2-12 is displayed.


26/87



Figure 2-12 Selecting a BIE board

Step 2 Select a BIE board.

If no site connects to the BIE, the Next button in the Configure Monitor Timeslot dialog box isunavailable.

Step 3 Click Next .

The Configure Monitor Timeslot dialog box is refreshed.

Step 4 Select a BIE port.

The Confirm dialog box as shown in Figure 2-13 is displayed.


27/87


28/87



If you click No in the Confirm dialog box, the Information dialog box as shown inFigure 2-15 is displayed.

Figure 2-15 Information prompt

Step 6 Select the site. Then configure Site Trunk Mode Description , Semi-permanent Connection and BIE Port Property one by one.

If the relay mode of the selected BIE is Full Rate Ring Topology, Half Rate Ring Topology, or 6 E1 Port Half Rate Topology, you have to configureBSC BIE Semi-perm. Con. at the same time.

If the selected site is configured with idle timeslots in initial mode, the Idle Timeslot button is available.If necessary, you can adjust the idle timeslot of the site.

You have to enter all the information and ensure its correctness

Step 7 Click Next in the Configure Monitor Timeslot dialog box as shown inFigure 2-14 .


----End

Procedure for Auto Calculate Mode

To configure the monitor timeslot in auto calculate mode, perform the following steps:


29/87


30/87



Step 4 Select a BIE port and site.

Step 5 Click Site Monitor Timeslot .

The Configure Site Monitor Timeslot dialog box as shown in Figure 2-18 is displayed.

Figure 2-18 Configuring the site monitor timeslot

Step 6 Configure the site monitor timeslot.

z To delete a monitor timeslot, select it and then click Delete .

z To add a monitor timeslot, click Add , and then change the default value.

z To modify Site BIE Port No. Connects Monitor Device or Abis Timeslot No.Connects Monitor Device , click the form and select the value.

z To modify End Channel No. , double-click the form to display the Set End Channel No. dialog box as shown in Figure 2-19 . Select End Equipment Type , BIE Port No. andBIE Timeslot No. , and then click OK . The system will calculate End Channel No.automatically.

You can select User Input to enter the value of End Channel No. if you want, and then

click OK to return to the Configure Site Monitor Timeslot dialog box.


31/87




Figure 2-19 Setting the end channel number

Step 7 In the Configure Site Monitor Timeslot dialog box, click OK to return to the ConfigureMonitor Timeslot dialog box as shown in Figure 2-17 .

Step 8 Click Next .


----End

2.7.3 Verification

After configuring the monitor timeslots, check that:



2.7.4 Data Table


Table 2-7 Data tables modified during the modification of monitor timeslots

No. Table Name

1 Semi-permanent Connection Table

2 Site BIE Trunk Mode Description Table

3 Site BIE Configuration Table

4 Signaling Channel Link Table


32/87



No. Table Name

5 BSC BIE Description Table

6 BSC BIE Active/Stby. Group Table

7 BSC BIE Semi-permanent Connection Table

8 Trunk Circuit Table

2.8 Modifying the Abis Bypass Switch

2.8.1 Task DescriptionPurpose To modify the Abis bypass switch of a BIE port

Prerequisite None

Note None

2.8.2 Procedure

To modify the Abis bypass switch of a BIE port, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify Abis Bypass Switch .

The Modify Abis Bypass Switch dialog box as shown in Figure 2-20 is displayed.


33/87




Figure 2-20 Selecting a BIE board

Step 2 Select a BIE board.

If no site connects to the BIE, the Next button in the Modify Abis Bypass Switch dialog box as shownin Figure 2-20 is unavailable.

Step 3 Click Next .

The Modify Abis Bypass Switch dialog box is refreshed, as shown in Figure 2-21 .

Figure 2-21 Selecting a port and Abis Bypass Switch

Step 4 Select the BIE port and Abis Bypass Switch .


34/87



If the selected BIE port does not connect to any site, the Abis Bypass Switch checkbox and the Next button are unavailable.

Step 5

Click Next .

The Modify Abis Bypass Switch dialog box is refreshed, as shown in Figure 2-22 .

If the selected BIE port is in auto mode, the Confirm dialog box as shown in Step 8 is displayed.

Figure 2-22 Modifying the TRX property

Step 6 Click TRX Property . Enter the values of all the TRX properties.

If the sites are in cascade mode, you have to configure Site Trunk Mode Description and BIE Port Property at the same time.

Step 7 Click Next .

The Confirm dialog box as shown in Step 8 is displayed.


35/87





Step 8 Click Yes .


----End

2.8.3 Verification

After modifying the Abis bypass switch, check that:



2.8.4 Data Table


Table 2-8 Data tables modified during the modification of the Abis bypass switch

No. Table Name

1 Radio Channel Configuration Table

2 BSC BIE Description Table

3 Site BIE Trunk Mode Description Table


36/87



No. Table Name

4 Site BIE Configuration Table

5 Signaling Channel Link Table

6 Site Description Table

7 BSC BIE Semi-permanent Connection Table


9 BSC BIE Active/Stby. Group Table

2.9 Dynamic Configuration Without CommandThis section shows how to maintain the data tables conveniently.

The section has the following parts:

z Configuring Trunk Circuits

z Configuring the BTS Software Index

z Configuring Flow Control Parameters

z Configuring Common Parameters z Configuring Semi-Permanent Connection

z Configuring Alarm Parameters

z Configuring the GMEM

z Configuring Board Software Loading

z Configuring Timer Data

z Modifying the Module Description


37/87




2.9.1 Configuring Trunk Circuits

Task Description

Purpose To modify the visibility of the FTC and the properties of trunk circuits onthe FTC

Prerequisite The FTC has been configured in the initial data configuration on the BSCData Auto Configuration System.

NoteThe boards such as the FTC, BIE and GLAP in the BSC use fullconfiguration. The FTC that is out of service cannot be deleted in theinitial data configuration.

Procedure

This part uses an example to show how to modify the property of the trunk circuit on the FTC.Assume that you have to modify the CIC value of No.72 FTC in BM1 as 31, 65535, 32, 33 61. The integers from 32 to 61 have an increment of 1.


Step 1 On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > Trunk Circuit .

The Dynamic Configuration without Command dialog box as shown in Figure 2-24 is displayed.

Figure 2-24 Configuring FTC trunk circuit parameters

Step 2 Click Trunk Circuit .


38/87



The Select FTC dialog box as shown in Figure 2-25 is displayed.

Figure 2-25 Selecting a FTC

Step 3 Select Module 1 from the Select Module drop-down list. Select 72 FTC from the All FTC inCurrent Module list box.

Step 4

Click Property or double-click 72 FTC .

The Set FTC Property dialog box as shown in Figure 2-26 is displayed.


39/87




Figure 2-26 Configuring the FTC property

Step 5 In the Circuit Property tab page, deselect Auto-Calculate Circuit Property . Then changethe CIC values to 31, 65535, 32, 33 62. In the Advanced tab page, change the value of Start CIC to 31.

z If you select Auto-Calculate Circuit Property , the system calculates the FTC circuit propertyautomatically. You need to enter the value of Start CIC in the Advanced tab page. For details, seethe M900/M1800 BSC Data Configuration Manual Initial Configuration .

z If you do not want to assign the CIC to a timeslot, set the CIC value of the timeslot to 65535.

z The value of Start CIC should be the minimum value among the 32 CIC values.

You can change the visibility of the FTC board in the Basic Information tab page as shownin Figure 2-27 .


40/87



Figure 2-27 Changing the FTC visibility

If the FTC is invisible, you cannot change the parameters of circuit visibility in the Advanced tab pageand the Circuit Property tab page.

Step 6 Click OK to return to the Select FTC dialog box as shown in Figure 2-25 .

Step 7 Click OK to return to the Dynamic Configuration without Command dialog box as shownin Figure 2-24 .

Step 8 Click Next .


----End

Verification

Check that the related data in the data tables and in the host are correctly modified.

Data Table



41/87




Table 2-9 Data tables modified during the modification of trunk circuits

No. Table Name


2 CIC Module Table

2.9.2 Configuring the BTS Software Index

Task Description

Purpose To configure the BTS software index for the software loading of the BTS

Prerequisite None

Note None

Procedure

Using an example, this part describes how to configure the BTS software index. Assume thatyou have to add the BTS 3002C IOMU software index.


Step 1 On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > BTS Software Index .

The Dynamic Configuration without Command dialog box as shown inFigure 2-28 is displayed.


42/87



Figure 2-28 Configuring the BTS software index parameters

Step 2 Click BTS Software Index .

The BTS Software Configuration dialog box as shown in Figure 2-29 is displayed.

Figure 2-29 BTS Software Configuration dialog box

Step 3 Click Add .

The Add Configuration Item dialog box as shown in Figure 2-30 is displayed.


43/87




Figure 2-30 Adding configuration items

Step 4 Select IOMU_MAIN in the Software Serial No. drop-down list. Enter the related valuessuch as software name and version No. in the corresponding fields.

Step 5 Click OK to return to the BTS Software Configuration dialog box.

Step 6 Click OK to return to the Dynamic Configuration without Command dialog box.

The Software Version Index No. is generated by the system. The Software Name should be thecomplete saving path of the software file.

Step 7 Click Next .


----End

Verification

The software loading on the Site Maintenance System is successful.

Data Table



44/87



Table 2-10 Data table modified during the modification of the BTS software index

No. Table Name

1 Site Software Configuration Table

2.9.3 Configuring Flow Control Parameters

Task Description

Purpose To configure the parameters of the flow control

Prerequisite None

Note None

Procedure

This part uses an example to show how to configure the parameters of flow control. Assumethat you have to change Abis Flow Control Counter T1 .


Step 1 On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > Flow Control .


Figure 2-31 Configuring flow control parameters


45/87




Step 2 Click Flow Control , and then enter the password.

Step 3 Click OK .

The Set Flow Control Table dialog box as shown in Figure 2-32 is displayed.

Figure 2-32 Configuring the flow control parameter table

Step 4 Change the value of Abis Flow Control Counter T1.

Step 5 Click OK to return to the Dynamic Configuration without Command dialog box as shownin Figure 2-31 .

Step 6 Click Next .


----End

Verification

Check that the related data in the data tables are correctly modified.

Data Table



46/87



Table 2-11 Data table modified during the modification of the flow control parameters

No. Table Name

1 Flow Control Parameter Table

2.9.4 Configuring Common Parameters

Task Description

Purpose To configure the common parameters

Prerequisite None

Note None

Procedure

This part uses an example to show how to change common parameters. Assume that you haveto change the value of Encryption Algorithm of Destination BSC into A5/7 .


Step 1 On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > Common Parameter .


Figure 2-33 Configuring common parameters


47/87




Step 2 Click Common Parameter .

The Common parameter Tables dialog box as shown in Figure 2-34 is displayed.

Figure 2-34 Common parameter tables

Step 3 In the Software Parameter Table tab page as shown in Figure 2-35 , select A5/7 from theEncryption Algorithm of Destination BSC drop-down list.


48/87



Figure 2-35 Selecting the encryption algorithm of the destination BSC

Table 2-12 lists the meaning of the parameters.

Table 2-12 Meaning of the software parameters

Parameter Name DefaultValue

Description

Encryption Algorithm of Destination BSC

Any The options are A5/1, A5/2, A5/3, A5/4, A5/5,A5/6, A5/7, and Any.

Type of Alarm Box New alarm box

The options are old alarm box and new alarm box.

BIE PCM Alarm Delay(s)

5 Unit: second

Value range: 015

Include Speech VersionIE in SDCCH Handover Message

Selected If it is selected, the SDCCH handover messagecarries the speech version IE.

Always Include Cell IDIE in AssignmentComplete Message

Not selected If it is selected, the assignment completemessage must carry the cell ID IE. If it is notselected, the assignment complete messagecarries the cell ID IE only when the servicecell changes during channel assignment.


49/87




Parameter Name DefaultValue

Description

Exclude CIC Pool IE inAssignment CompleteMessage

Not selected If it is selected, the assignment completemessage will not carry the CIC pool IE. If it isnot selected, the assignment complete messagewill keep the current CIC Pool IE processingmechanism.

Exclude CIC Pool IE inHandover CompleteMessage

Not selected If it is selected, the handover completemessage will not carry the CIC pool IE. If it isnot selected, the handover complete messagewill keep the current CIC pool IE processingmechanism.

Support Group CircuitOperation on A-Interface

Selected If it is selected, the group circuit operation onA-interface is available. If it is not selected,

the group circuit operation on A-interface isunavailable.


Step 5 Click Next .


----End

Verification


For the Software Parameter Table , ensure that the related data are set to each BSC module.For other data tables, check that the DBF is correctly refreshed.

Data TableTable 2-13 lists the modified data tables in the BSC Data Management System.

Table 2-13 Data tables modified during the modification of common parameters

No. Table Name

1 Cell Call Control Table

2 Module Parameter Table

3 Common Maximum Tuple Table


50/87



No. Table Name

4 Module Maximum Tuple Table

5 Software Parameter Table

2.9.5 Configuring Semi-Permanent Connection

Task Description

Purpose To configure the parameters of semi-permanent connection

Prerequisite None

Note None

Procedure

To configure the parameters of semi-permanent connection, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > Semi-permanent Connection .


Figure 2-36 Configuring semi-permanent connection

Step 2

Click Semi-Permanent Connection .


51/87




The Semi-permanent Connection Table dialog box as shown in Figure 2-37 is displayed.

Figure 2-37 Semi-permanent connection table

Step 3 Add, modify, or delete a record by clicking Add , Modify , or Delete respectively.


Step 5 Click Next .


----End

VerificationCheck that the related data in the data tables and in the host are correctly modified.

Data Table



52/87



Table 2-14 Data table modified during the modification of semi-permanent connection

No. Table Name

1 Semi-permanent Connection Table

2.9.6 Configuring Alarm Parameters

Task Description

Purpose To configure alarm parameters

Prerequisite None

Note None

Procedure

This part uses an example to show how to configure alarm parameters. Assume that you haveto configure the BSC alarm parameters.

Step 1 On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > Alarm > BSC Alarm Information Configuration .


Figure 2-38 BSC alarm information configuration

Step 2 Click BSC Alarm Information Configuration .


53/87




The Supervisor dialog box as shown in Figure 2-39 is displayed.

Figure 2-39 Password verification

Step 3 Enter the password.

The Alarm Parameter Table dialog box as shown in Figure 2-40 is displayed.

Figure 2-40 Alarm parameter table

Step 4 Modify the values of the BSC alarm parameters.

You cannot modify the values of other alarm parameters.


Step 6 Click Next .


54/87




----End

Verification

The related data in the data tables and in the host are correctly modified.

Data Table


Table 2-15 Data tables modified during the modification of alarm parameters

No. Table Name

1 Alarm Parameter Configuration Table

2 Alarm Environment Variable Table

3 BTS Alarm Information Configuration Table

4 BTS Alarm Environment Variable Table

5 Alarm Information Parameter Table

6 BM Alarm Screening Table

7 AM Alarm Screening Table

8 AM Alarm Environment Variable Table

2.9.7 Configuring the GMEM

Task Description

Purpose To configure the IP address of the GMEM

Prerequisite The GMEM information is configured in the initial data configuration atthe BSC Data Auto Configuration System.

NoteYou can modify the attributes of all the GMEMs installed in the BM inone operation.


55/87


56/87



Figure 2-42 Selecting a GMEM


Step 4 Select 5 GMEM from the All GMEM in Current Module box. Then click Property or double-click 5 GMEM .

The Set GMEM Property dialog box as shown in Figure 2-43 is displayed.

Figure 2-43 Configuring the GMEM property

Step 5 Click Add to add a GMEM IP address configuration item.


57/87




Step 6 Click OK to return to the Select GMEM dialog box.


Step 8 Click Next in the Dynamic Configuration without Command dialog box.


----End

Verification


Data Table


Table 2-16 Data table modified during the modification of the IP address of the GMEM

No. Table Name

1 GMEM Configuration Table

2.9.8 Configuring Board Software Loading

Task Description

Purpose To configure the loading information of board software

Prerequisite None

Note None

Procedure

To configure the loading information of board software, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > Board Software Loading .


58/87




Figure 2-44 Configuring loading information

Step 2 Click Board Software Loading .

The Board Software Loading Table dialog box as shown in Figure 2-45 is displayed.

Figure 2-45 Board software loading table

Step 3 Add, modify, or delete a record by clicking Add , Modify , or Delete respectively.



59/87




Step 5 Click Next .


----End

Verification


Data Table


Table 2-17 Data table modified during the modification of the loading information of boardsoftware

No. Table Name

1 Board Software Loading Table

2.9.9 Configuring Timer Data

Task Description

Purpose To configure timer data

Prerequisite None

Note None

Procedure

To configure timer data, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > Timer Data .



60/87



Figure 2-46 Configuring timer data

Step 2 Click Timer Data .

The Local Data Default Config dialog box as shown in Figure 2-47 is displayed.

Figure 2-47 Timer data

Step 3 Modify the timer data.


Step 5 Click Next .



61/87




----End

Verification


Data Table


Table 2-18 Data table modified during the modification of timer data

No. Table Name

1 Timer Table

2.9.10 Modifying the Module Description Table

Task Description

Purpose To change the ID of the PCU that a module connects to

Prerequisite None

Note None

Procedure

To change the PCU ID, perform the following steps:

Step 1

On the BSC Data Auto Configuration System, choose BSC > Dynamic Configurationwithout Command > Module Description .



62/87



Figure 2-48 Dynamic configuration without command

Step 2 Click Module Description Table .

The Common Parameter Tables dialog box as shown in Figure 2-49 is displayed.

Figure 2-49 Module description table

Step 3 Change the PCU ID of the module.


63/87





Step 5 Click Next .


----End

Verification


Data Table


Table 2-19 Data table modified during the modification of the module description

No. Table Name

1 Module Description Table

2.10 Importing Network Parameters


Purpose To import network parameters from template files

Prerequisite None

Note

The template files can be edited only in Microsoft Excel. The files have to

be exported to Microsoft Excel before being edited. For details, refer tosection 2.11 "Exporting Network Parameters ."

2.10.2 Procedure

To import network parameters, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Import Network Parameters .

The Open dialog box as shown in Figure 2-50 is displayed.


64/87



Figure 2-50 Selecting the text file

Step 2 Select the text file, and then click Open .

The Dynamic Configuration dialog box as shown in Figure 2-51 is displayed.



----End

2.10.3 Verification



65/87




2.11 Exporting Network Parameters


Purpose To export network parameters

Prerequisite None

NoteThe exported network parameters are saved as a text file. You can edit thisfile in Microsoft Excel and then import it. For details, refer to section 2.10"Importing Network Parameters ."

2.11.2 Procedure

To export network parameters, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Export Network Parameters .

The Export Network Parameters dialog box as shown in Figure 2-52 is displayed.

Figure 2-52 Exporting network parameters

Step 2 Select the type of the export network parameters from the Select Export Network Parameter Type drop-down list, and then select cells or external cells.

Step 3 Click Export Parameter .

The Save As dialog box as shown in Figure 2-53 is displayed.


66/87



Figure 2-53 Saving the text file

Step 4 Enter the file name, and then click Save .

The Information prompt as shown in Figure 2-54 is displayed.

Figure 2-54 Information prompt

Step 5 Click OK to return to the Export Network Parameters dialog box.

Step 6 Click Exit .

If the selected cell or external cell contains redundant information, such as redundant frequencies, therelated prompt will be displayed. The redundant information will not be exported to the text file.

----End

2.11.3 Verification

Check that all the exported text files are correct.


67/87




This operation does not change any data table.

2.12 Modifying Reserved Parameters


Purpose To modify the reserved parameters

Prerequisite None

Note

The reserved parameters are used for the functions or software patches to be developed in the future. Each of the BM, site, cell, and TRX has its

own reserved parameters. You can only change these parameters. If a sitedoes not exist, you cannot add reserved parameters for it.

2.12.2 Procedure

This part uses an example to show how to modify the reserved parameters. Assume that youhave to modify the reserved parameters of TRXs.


Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify Reserved Parameters > TRX .

The Modify TRX Reserved Parameter dialog box as shown in Figure 2-55 is displayed.


68/87



Figure 2-55 Selecting TRXs

If you choose BSC > Modify Reserved Parameters > Module , the Modify TRX ReservedParameter dialog box as shown in Figure 2-56 is displayed.

Figure 2-56 Selecting a module

Step 2 Select TRXs, and then click Next .

The Modify TRX Reserved Parameter dialog box as shown in Figure 2-57 is displayed.


69/87




Figure 2-57 Modifying the reserved parameters

Step 3 Select the TRX and click Modify Reserved Parameters .

The Reserved Parameters Configuration dialog box as shown in Figure 2-58 is displayed.

Figure 2-58 Reserved Parameters Configuration dialog box

To modify the parameter, click the parameter and enter the value.


70/87



To modify a batch of parameters in one column in one operation, modify one parameter of them, and then right-click the parameter to choose Batch Modify > Current col fromcurrent row or Current col. from begin .

Step 4

Click OK to return to the Modify TRX Reserved Parameter dialog box as shown in Figure2-57 .

Step 5 Click Next .


----End

2.12.3 Verification


2.12.4 Data Table


Table 2-20 Data tables modified during the modification of the reserved parameters

No. Table Name1 BM Reserved Parameter Table

2 Site Reserved Parameter Table

3 Cell Reserved Parameter Table

4 TRX Reserved Parameter Table

2.13 Configuring the SS7 Property


Purpose To configure the SS7 property without resetting the BSC

Prerequisite None

Note None


71/87


72/87



You can modify the values of BSC Signaling Point Code and MSC Signaling Point Code in theConfigure SS7 Property dialog box as shown in Figure 2-60 .

Step 3

Select an E3M, and then click Configure SS7 Property .

The Set E3M Board Property dialog box as shown in Figure 2-61 is displayed.

Figure 2-61 Configuring the E3M board property

In the Set E3M Board Property dialog box, you can modify the properties of the existingSS7 links. These properties include MSM TS , BIE TS , FTC No ., TransparentTransmission BIE Port No. for SS7 Signaling , and Signaling Link . You can also add or delete SS7 signaling links.

Step 4 Click OK to return to the Configure SS7 Property dialog box.

Step 5 Click Next .



73/87




----End

2.13.3 Verification

Check that the modified SS7 signaling links are normal.

2.13.4 Data Table


Table 2-21 Data tables modified during the modification of the SS7 property

No. Table Name

1 E3M E1 Configuration Table

2 BM_E3M_E1 Configuration Table


4 SCCP SSN Table

5 SCCP DSP Table

6 MTP DSP Table

7 MTP Linkset Table

8 MTP Link Table

9 CIC Module Table

10 Office Direction Table


2.14 Modifying the PB Interface Property


Purpose To configure the transmission modes on the PB interface without resettingthe BSC

Prerequisite None

Note None


74/87



2.14.2 Procedure

To modify the PB interface property, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify PB Interface Property .

The Modify PB Interface Property dialog box as shown in Figure 2-62 is displayed.

Figure 2-62 Modifying PB Interface Property

Step 2 Change the value of Transmission Mode .

Step 3 Click Next .


----End

2.14.3 Verification

Check that the modified PB links are normal.

2.14.4 Data Table



75/87




Table 2-22 Data table modified during the modification of the property of the PB interface

No. Table Name

1 LAPD Signaling Connection Table

2.15 Modifying the BIE Trunk Mode


Purpose To modify the BIE trunk modes without changing the sites under the BIE

Prerequisite None

Note None

2.15.2 Procedure

To modify the BIE trunk mode, perform the following steps:

Step 1 On the BSC Data Auto Configuration System, choose BSC > Modify BIE Trunk Mode .

The Modify BIE Trunk Mode dialog box as shown in Figure 2-63 is displayed.


76/87



Figure 2-63 Selecting a BIE

Step 2 Select the BIE board.

The Modify BIE T

01-2 dynamic configuration (bsc).pdf

Documents