01-01 signaling fundmental
TRANSCRIPT
-
7/30/2019 01-01 Signaling Fundmental
1/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual Contents
Issue 02 (2007-06-30) Huawei Technologies Proprietary i
Contents
1 Signaling Fundamentals...........................................................................................................1-1
1.1 Overview of Interfaces..................................................................................................................................1-2
1.1.1 A Interface............................................................................................................................................1-2
1.1.2 Abis Interface.......................................................................................................................................1-3
1.1.3 Um Interface ................................................................ .................................................................. ......1-3
1.2 A Interface................................................................ ..................................................................... ................1-3
1.2.1 Overview of the A Interface.................................................................................................................1-3
1.2.2 Layers of the A Interface......................................................................................................................1-4
1.3 Abis Interface .......................................................... ....................................................................... .............1-10
1.3.1 Overview of the Abis Interface ................................................................. .........................................1-10
1.3.2 Layers of the Abis Interface...............................................................................................................1-13
1.4 Um Interface................................................................................................................................................1-19
1.4.1 Overview of the Um Interface............................................................................................................1-19
1.4.2 Physical Layer....................................................................................................................................1-20
1.4.3 Data Link Layer ............................................................ ..................................................................... 1-20
1.4.4 Layer 3 ............................................................ ....................................................................... ............1-22
-
7/30/2019 01-01 Signaling Fundmental
2/28
Figures
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
ii Huawei Technologies Proprietary Issue 02 (2007-06-30)
Figures
Figure 1-1 Signaling model of the GSM .................................................................... ........................................1-2
Figure 1-2 Protocol reference model of the A interface...................................................................................... 1-3
Figure 1-3 Signaling message processing part ........................................................................ ...........................1-5
Figure 1-4 Protocol reference model of the Abis interface...............................................................................1-11Figure 1-5 Structure of the Abis interface ........................................................................... .............................1-12
Figure 1-6 L2 logical links on the Abis interface ................................................................... ..........................1-13
Figure 1-7 Basic structure of the managed objects...........................................................................................1-17
Figure 1-8 Three layers of the Um interface ............................................................ ........................................1-19
Figure 1-9 Interfaces of L1...............................................................................................................................1-20
Figure 1-10 L3 protocol model of the Um interface.........................................................................................1-24
Figure 1-11 Communications between RR sub-layers ............................................................ .........................1-25
Figure 1-12 Communications between MM sub-layers .......................................................... .........................1-25
-
7/30/2019 01-01 Signaling Fundmental
3/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual Tables
Issue 02 (2007-06-30) Huawei Technologies Proprietary iii
Tables
Table 1-1 Major functions of the BSSAP................................................................. ..........................................1-8
Table 1-2 Administrative state ................................................................. ......................................................... 1-17
Table 1-3 Operational state...............................................................................................................................1-18
Table 1-4 Availability status .................................................................. ........................................................... 1-18
-
7/30/2019 01-01 Signaling Fundmental
4/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-1
1 Signaling FundamentalsAbout This Chapter
The following table lists the contents of this chapter.
Section Describes
1.1 Overview of Interfaces The functions of the BSS interfaces.
1.2 A Interface The protocol model on the A interface and each layer of the Ainterface.
1.3 Abis Interface The protocol model on the Abis interface and each layer of
the Abis interface.1.4 Um Interface The protocol model on the Um interface and each layer of the
Um interface.
-
7/30/2019 01-01 Signaling Fundmental
5/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-2 Huawei Technologies Proprietary Issue 02 (2007-06-30)
1.1 Overview of Interfaces
The Base Station Subsystem (BSS) use standard external interfaces: Um interface between aMobile Station (MS) and the BSS and the A interface between the BSS and the Mobile
Switching service Center (MSC).
The interface protocols and interface procedures strictly follow the EuropeanTelecommunications Standards Institute (ETSI) specifications.
The Abis interface between the Base Transceiver Station (BTS) and the Base Station Controller
(BSC) and the interface between the BSS and the Operation and Maintenance Center (OMC)are internal interfaces. These interfaces are related to the specific equipment from differentmanufacturers. There are many regulations drafted by the ETSI for the Abis interface between
the BTS and the BSC, but the regulations are incomplete.
Figure 1-1 shows the signaling model of the Global System for Mobile communications
(GSM).
Figure 1-1Signaling model of the GSM
CM
MM
RR
LAPDm
Sign.
Layer1
L3
L2
L1
BTSM
MS
Um
SCCP
MTP
BTSM
RR BSSMAP
Abis
BTS
BSC
MSC
A
BSC
Sign.
Layer1
Sign.
Layer1
Sign.
Layer1
RR
LAPDLAPDm LAPD
CM
MM
BSSMAP
SCCP
MTP
MS: Mobile Station BTS: Base Transceiver Station
BSC: Base Station Controller MSC: Mobile services Switching Center
CM: Connection Management MM: Mobility Management
RR: Radio Resource Management MTP: Message Transfer Part
SCCP: Signaling Connection Control Part LAPD: Link Access Procedure on the D channel
BTSM: Base Transceiver Station Management LAPDm: Link Access Procedure on the Dm channel
BSSMAP: Base Station Subsystem Management Application Part
1.1.1 A Interface
The A interface is a standard interface between the BSS and the Network Subsystem (NSS),that is, between the BSC and the MSC. The physical links on the A interface belong to standard
2.048 Mbit/s Pulse Code Modulation (PCM) digital links. The A interface is used to transmit
the information about MS management, BTS management, mobility management, connectionmanagement, and to perform service flow control.
-
7/30/2019 01-01 Signaling Fundmental
6/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-3
1.1.2 Abis Interface
The Abis interface defines the standard for the communications between the BSC and the BTSin the BSS. The links on the Abis interface belong to standard 2.048 Mbit/s PCM digital links.
The Abis interface provides all MS-oriented services, controls BTS radio equipment, andmanages the allocation of radio frequencies.
1.1.3 Um Interface
The Um interface lies between an MS and the BTS. It is used for the interworking between the
MS and the fixed part of the GSM system. The links on the Um interface belong to radio links.The Um interface is used to transmit the information about radio resource management,mobility management, and connection management.
1.2 A Interface
1.2.1 Overview of the A Interface
The A interface lies between the BSC and the MSC. It is a standard interface in GSMspecifications. It may interconnect with the equipment from different manufactures. SS7 is used
on the A interface.
Physically, the A interface is the trunk circuit and trunk interface between the BSC and the MSC.Figure 1-2 shows the signaling protocol reference model of the A interface.
Figure 1-2Protocol reference model of the A interface
DTAP: Direct Transfer Application Part MTP: Message Transfer Part
SCCP: Signaling Connection Control Part BSSAP: Base Station Subsystem Application Part
BSSMAP: Base Station Subsystem Management Application Part
-
7/30/2019 01-01 Signaling Fundmental
7/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-4 Huawei Technologies Proprietary Issue 02 (2007-06-30)
1.2.2 Layers of the A Interface
Physical Layer
The physical layer of the A interface is a 75-ohm coaxial cable or 120-ohm twisted pair. Thetransmission rate of this layer is 2 Mbit/s. The physical layer of the A interface has thefollowing features:
z The 2 Mbit/s transmission rate complies with G.703.
z The frame structure, synchronization, and timing comply with G.705.
z The fault management complies with G.732.
z CRC4 complies with G.704.
MTP
The Message Transfer Part (MTP) provides reliable signaling message transfer in the signalingnetwork. It takes measures to avoid or reduce the loss of messages, repeated messages, and
out-of-sequence packetsin case of system failures and signaling network failures.
The MTP protocols are defined in ITU-T Q.701Q.710 recommendations.
The MTP comprises three function layers: signaling data link function layer, signaling link
function layer, and signaling network function layer.
z Signaling data link function layer
The signaling data link function layer (layer 1) defines physical, electrical, and functionalfeatures of signal data. It specifies how to connect with data links.
A signaling data link is used to transmit signaling in both directions. It comprises two data
paths with the same data rate (64 kbit/s) but in two opposite directions. Generally, thesignaling data link occupies timeslot 16 of a trunk. The specific timeslot is determinedthrough the negotiation between the BSC and the MSC. The timeslot can be used toestablish a semi-permanent connection.
A signaling data link serves as an information bearer of SS7. One of the important features
of the signaling data link is that the information transmitted on the link is transparent, thatis, the data transferred on the link cannot be changed. Therefore, equipment such as echocanceller, digital attenuator, and A/u rate converter, cannot be connected to this link.
z Signaling link function layer
Signaling link function layer (layer 2) specifies the functions and procedures for sendingsignaling to data links. It, together with layer 1, provides reliable signaling message
transfer between two directly connected signaling points.Due to long-distance transmissions, a certain rate of bit errors may be caused on the data
link between adjacent signaling points. However, no error is allowed in SS7 signalingmessage codes. The function of layer 2 is to guarantee error-free transmissions of message
codes in the case that there are bit errors on layer 1. Layer 2 performs the followingfunctions: signaling unit delimitation, signaling unit alignment, error detection, error
correction, initial alignment, processor fault detection, flow control, and signaling linkerror rate monitoring.
z Signaling network function layer
By controlling the route and performance of the signaling network, signaling network
function layer (layer 3) guarantees reliable transmission of signaling information to theuser part, no matter whether the signaling network is in normal state or not. The signaling
-
7/30/2019 01-01 Signaling Fundmental
8/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-5
network is functionally classified into signaling message processing part and signalingnetwork management part.
z Signaling message processing part
The signaling message processing part sends signaling messages from the user part of a
signaling point to the target signaling links or user parts. The user part in the BSS onlyrefers to the SCCP. The signaling message processing part comprises three smaller parts:message routing (MRT), message discrimination (MDC), and message distribution(MDT), as shown in Figure 1-3.
Figure 1-3Signaling message processing partMTP user part
MDC MRT
MDT
Messages to
the local office
Messages to other
signaling points
Signaling message
processing at MTP layer 3
Signaling message
processing at MTP layer 2
MRT
The MRT selects message routes. In other words, by using the information contained in
the route mark, destination signaling point code (DPC) and signaling link selectioncode (SLS), the MRT selects a signaling link for signaling messages, so that themessages can be transmitted to a destination signaling point.
MDC
The MDC receives the messages from layer 2 to ascertain whether the destination ofthe messages is the local signaling point.If the destination is the local signaling point,
the MDC sends the messages to the MDT. If the destination is not the local signalingpoint, the MDC part sends the messages to the MRT.
MDT
The MDT allocates the messages from the MDC to the user part, the signaling networkmanagement part, and the test & maintenance part.
z Signaling network management part
The signaling network management part reconstructs the signaling network, and keepsand recovers the normal transmission of signaling units when the signaling network fails.
It consists of three smaller parts: signaling traffic management (STM), signaling linkmanagement (SLM), and signaling route management (SRM).
STM
-
7/30/2019 01-01 Signaling Fundmental
9/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-6 Huawei Technologies Proprietary Issue 02 (2007-06-30)
The STM is used to transmit the signaling data from one link or route to another or tomultiple available links or routes when the signaling network fails. It is also used totemporarily reduce signaling traffic in case of congestion at a signaling point.
SLM
The SLM is used to recover, enable, or disconnect the signaling links in the signalingnetwork. It is used to ensure the provisioning of certain pre-determined link groups.The connections between signaling data links and signaling terminals are normally
established through man-machine commands. The operations in the signaling systemcannot automatically change the previous connection relations.
SRM
The SRM is used to ensure the reliable exchange of signaling route availabilityinformation between signaling points so that signaling routes can be blocked orunblocked if necessary. The SRMmainly comprises procedures such as prohibited
transfer, allowed transfer, controlled transfer, and restricted transfer, as well assignaling route group test and signaling route group congestion test.
SCCP
The SCCP, with the help of MTP layer 3, is designed to provide sound network layer functions
and reliable services for information exchange in any form.
The network layer services provided by the SCCP are classified into connectionless service andconnection-oriented service.
The connectionless service indicates that an MS does not establish a signaling connection inadvance, but uses the routing function of the SCCP and of the MTP to directly transmit datainformation in the signaling network. It is applicable to the transmission of a small number of
data.
The connection-oriented service indicates that an MS establishes a signaling connection inadvance and directly transmits data on the signaling connection, instead of using the routeselection function of the SCCP. The connection-oriented service is applicable to the
transmission of a large number of data, and effectively shortens the transmission delay of batch
data.
The SCCP can also perform routing and network management functions.
The SCCP performs addressing based on address information such as the DPC, subsystem
number (SSN), and global title (GT). The DPC and SSN are used to identify different SCCP
users, such as the ISUP users, MAP users, TCAP users, and BSSAP users in the same node, soas to compensate the insufficiency of MTP users and to enlarge the addressing scope. The BSSdoes not use the GT addressing mode, which is not introduced here.
The SCCP performs the following network management functions:
z Managing signaling point states and subsystem states
z Performing active/standby subsystem switchover
z Broadcasting status information
z Testing subsystem states
The SCCP management (SCMG) is used to maintain the network functions by reselecting a
route or adjusting the traffic volume in case of network failures or congestion.
The SCCP protocols are defined in ITU-T Q.711Q.716 recommendations.
-
7/30/2019 01-01 Signaling Fundmental
10/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-7
BSSAP
1. Overview of BSSAP
The BSSAP protocol, which serves as the A interface specification, describes two types of
messages: BSSMAP messages and DTAP message.For DTAP messages, the A interface is merely equivalent to a transport channel. On the BSSside, DTAP messages are directly transmitted to radio channels. On the NSS side, DTAPmessages are transmitted to the specific functional processing unit.
The BSSAP protocol is defined in GSM Rec. 08.08 and 04.08.
2. Typical message contents
z DTAP messages
The DTAP messages can be classified into Mobile Management (MM) messages and Call
Control (CC) messages based on the functional units used to process DTAP messages onthe NSS side.
The MM messages consist of authentication-related messages, ConfigurationManagement (CM) service request, identification request, IMSI detach, location update,MM state, TMSI reallocation, and so on.
The CC messages consist of the messages related to alerting, call proceeding, connection,setup, modification, release, disconnection, notification, state query, DTMF startup, and
so on.
z BSSMAP messages
The BSSMAP messages can be classified into connectionless messages andconnection-oriented messages.
The connectionless messages include Block/Unblock, Circuit Group Block/Unblock,Handover, Resource, Reset, and Paging.
The Block/Unblock messages consist of Block, Block ACK, Unblock, and UnblockACK.
The Circuit Group Block/Unblock messages include Circuit Group Block, CircuitGroup Block ACK, Circuit Group Unblock, and Circuit Group Unblock.
Handover messages include Handover Candidate Enquire and Handover CandidateEnquire Response.
The resources messages include Resource Request and Resource Indication.
The Reset messages include Reset and Reset ACK.
The connection-oriented messages include Assignment, Handover, Clear, and Ciphermessages.
The Assignment messages include Assignment Request, Assignment Complete, andAssignment Error.
The Handover messages include Handover Request, Handover Request ACK,Handover Command, Handover Complete, and Handover Failure.
The Clear messages include Clear Request and Clear Complete.
The Cipher messages include Cipher Mode Command and Cipher Mode Complete.
3. BSSAP protocol functionality
The BSSAP protocol can function in connection-oriented mode and connectionless mode.
When an MS needs to exchange service-related messages with the NSS over radio channelswhen there is no MS-related SCCP connection between the BSS and the NSS, a new connection
shall be established. A new connection shall also be set up for external handovers.
-
7/30/2019 01-01 Signaling Fundmental
11/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-8 Huawei Technologies Proprietary Issue 02 (2007-06-30)
There are two types of connection setup:
z When an MS sends an Access Request message on the RACH, the BSS assigns a
dedicated channel (SDCCH or TCH) to the MS. After a layer 2 connection is set up on theassigned SDCCH or FACCH, the BSS starts a connection setup.
z When the MSC decides to carry out an external handover (the target BSS might be theoriginal BSS), it must reserve a new DCCH or TCH from the target BSS. In this scenario,the MSC starts a connection setup.
By using the connection-oriented and connectionless messages, the BSSAP protocolimplements the functional procedures as shown in Table 1-1.
Table 1-1Major functions of the BSSAPNumber Function Description
1 Assignment Assignment is to ensure that dedicated radio resources areproperly allocated or re-allocated to an MS. The BSS
automatically processes the initial random access andimmediate assignment of an MS to a DCCH, without thecontrol of the MSC.
2 Block/unblock circuit
During an assignment procedure, the MSC needs to select
available terrestrial circuits. If the BSS regards that someterrestrial circuit can no longer be used, it must notify the
MSC by initiating a Block/Unblock procedure.
3 Resourceindication
Resource indication serves to notify the MSC of thefollowing:
zNumber of radio resources that can be used as TCHs in theBSS
zNumber of all usable radio resources that can provideservices or have been assigned
It is not easy to obtain the previous information directly from
the MSC-controlled services. The information must be takeninto consideration when the MSC decides an externalhandover.
4 Reset Reset is to initialize the BSS or the MSC. For instance, if the
BSS goes faulty or loses all the reference messages aboutprocessing, it sends a Reset message to the MSC. On receipt
of the Reset message, the MSC releases the affected calls,deletes the affected reference messages, and sets all the
circuits related to the BSS to idle.If the MSC or BSS is only partially faulty, the affected partscan be cleared through the Clear procedure.
-
7/30/2019 01-01 Signaling Fundmental
12/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-9
Number Function Description
5 Handover
request
The BSS may send a Handover Request to the MSC,
requesting the MSC to hand over an MS, to which dedicatedresources have been allocated. The handover reasons as are asfollows:
z The BSS detects a radio cause for a handover.
z The MSC starts a Handover Candidate Enquirer procedureand the MS is waiting for a handover.
z Due to congestion, the serving cell needs to be changedduring the call setup such as directed retry.
The BSS shall resend the Handover Request message at acertain interval till one of the following situations occurs:The BSS receives a Handover Command message from the
MSC.
z
The BSS receives a Reset message.z All the communications with MSs are disrupted and the
processing is stopped.
z The processing is complete, for example, the call is cleared.
6 Handover
resourceallocation
Handover resources allocation enables the MSC to request for
resources from the target BSS based on the handover request.The target BSS will reserve resources and wait for an MS toaccess the reserved resources (channel).
7 Handoverprocedure
Handover procedure is a procedure in which the MSC
instructs an MS to access the radio resources of a target cell.
When the handover is carried out, the original dedicated radioresources and terrestrial resources are maintained all the time
until the MSC sends a Clear Command message or theresources are reset.
8 Radio
resource
release andterritorialresourcerelease
When a processing is complete, the MSC sends a Clear
Command message to the BSS to release radio resources.
Upon receipt of the message, the BSS starts the Clearprocedure on the radio interface, sets the configured terrestrial
circuit to idle, and responds with a Clear Complete message tothe MSC.
Upon receipt of the Clear Complete message, the MSC
releases the terrestrial resources.If the BSS needs to release resources, it sends a Clear Request
message to the MSC, requesting the MSC to initiate a releaseprocedure to release the specific terrestrial and radioresources.
9 Paging The paging to an MS is transmitted through the BSSMAP
over the SCCP connectionless service. When the BSSreceives a Paging Response message on the Um interface, itestablishes an SCCP connection to the MSC. The paging
response message, which is carried in the Complete L3Information, is transmitted to the MSC through this SCCPconnection.
-
7/30/2019 01-01 Signaling Fundmental
13/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-10 Huawei Technologies Proprietary Issue 02 (2007-06-30)
Number Function Description
10 Flow control A flow control can prevent a network entity from receiving
too much traffic. The flow control on the A interface isimplemented through the control the traffic at the traffic
source. Five levels of flow control are available. Flow controlcan be carried based on subscriber classes.
11 Classmarkupdate
Classmark Update serves to notify a receiving entity of theclassmark messages from an MS. Generally, the BSS notifies
the MSC upon receipt of the classmark messages from an MS.It is also likely that when a handover is complete, the MSC
sends the new BSS the classmark messages of a specific MSthrough the A interface.
12 Cipher modecontrol
The Cipher Mode Control procedure allows the MSC to sendthe Cipher Mode Control message to the BSS and to start the
subscriber equipment and signaling cipher equipment using acorrect ciphering key (Kc).
13 Queueindication
The Queue Indication procedure serves to notify the MSC thatthe BSS wants to delay the allocation of necessary radio
resources. The procedure is valid only when the queuingfunction is used for traffic channel assignment and trafficchannel handover in the BSS.
14 Loadindication
Load Indication serves to notify all neighbor BSS entities of
the traffic state of a cell so that the handover services in anMSC can be controlled in a centralized manner. In a certainvalid period, the neighbor BSS will take the traffic states of
neighbor cells into account during a handover.
1.3 Abis Interface
1.3.1 Overview of the Abis Interface
The Abis interfaces lies between the BTS and the BSC. It complies with the specifications
defined by GSM Rec. 08.5X series. The Abis interface is merely an internal interface of the
BSS. The interworking between the BSC and BTS equipment from different manufactures isnot available temporarily.
The terrestrial traffic channels on the Abis interface map with the radio traffic channels on theUm interface in one-to-one manner.
Protocol Reference Model of the Abis Interface
Figure 1-4 shows the protocol reference model of the Abis interface.
-
7/30/2019 01-01 Signaling Fundmental
14/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-11
Figure 1-4Protocol reference model of the Abis interface
LAPDm
Sign.
Layer 1
LAPD
Layer 1 Layer 1
SCCP
MTP
BTSM
RR BSSAP
Abis interface
BTS BSC
RR BTSM
LAPD
BTSM: BTS Management BSSAP: Base Station Subsystem Application Part
RR: Radio Resource management SCCP: Signaling Connection Control Part
LAPD: Link Access Procedure on the D channel MTP: Message Transfer Part
LAPDm: Link Access Procedure on the Dm channel
z Layer 1 of the Abis interface is a physical link. It receives and transmits data based on thebottom-layer driver of the hardware.
z The layer 2 protocol of the Abis interface runs based on the LAPD. The LAPD addresses aTransceiver (TRX) or Base Control Function (BCF) through the Terminal EquipmentIdentifier (TEI). It uses different logical links for message transmissions:
Radio signaling links (RSL) used to transmit service management messages
Operation and maintenance links (OML) used to transmit network management
messages
Layer 2 management links (L2ML) used to transmit L2 management messages
z RR messages are mapped onto the BSSAP in the BSC. Most RR messages are treated astransparent messages in the BTS, but some of them have to be interpreted and executed by
the BTS. For example, ciphering, random access, paging, and assignment messages areprocessed by the BTS Management (BTSM) entities in the BSC and in the BTS.
z Neither the BSC or the BTS interprets Connection Management (CM) messages andMobility Management (MM) messages. These messages are transmitted on the A interface
by the Direct Transfer Application Part (DTAP). On the Abis interface, DTAP messagesare transmitted as transparent messages.
Structure of the Abis Interface
The Abis interface supports three types of internal BTS configuration:
z A single TRX
z Multiple TRXs connected with the BSC through one physical link
z Multiple TRXs connected with the BSC through different physical links
-
7/30/2019 01-01 Signaling Fundmental
15/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-12 Huawei Technologies Proprietary Issue 02 (2007-06-30)
Figure 1-5Structure of the Abis interface
Abis
BTS3
BTS2
BTS1
A
Abis
MSCBSC
TRX
BCF
TRX
BCF
Abis
BSS
TRX
TRX
TRX
TRX
TRX
TRX
BCF
z Transceiver (TRX) is a functional entity defined in the Public Land Mobile Network
(PLMN). It supports eight physical channels belonging to the one TDMA frame.z BCF is the functional entity that performs common control functions including BTS
initialization, software loading, channel configuration, and operation and maintenance.
There are two types of channels on the Abis interface. They are described as follows:
z Traffic channels, which have transmission rates of 8 kbit/s, 16 kbit/s, and 64kbit/s, andcarry speech or data from radio channels.
z Signaling channels, which have transmission rates of 16 kbit/s, 32 kbit/s, and 64kbit/s, andcarry signaling between the BSC and an MS, and between the BSC and the BTS
A TEI is assigned to obtain the unique address of a TRX. Each BCF has a unique TEI. Three
different logical links are defined with a TEI, as shown in Figure 1-6.
z RSL: used to support traffic management procedures, one for each TRX
z OML: used to support network management procedures, one for each BCF
z L2ML: used to transmit L2 management messages
-
7/30/2019 01-01 Signaling Fundmental
16/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-13
Figure 1-6L2 logical links on the Abis interface
TEI 1L2ML SAPI=63
RSL SAPI=0
OML SAPI=62
Layer 2
TEI
Management
TRX
TRX
TRX
BCF
L2ML SAPI=63
RSL SAPI=0
OML SAPI=62
L2ML SAPI=63
RSL SAPI=0
OML SAPI=62
BCF
BCF
BCF
BCF
L2ML SAPI=63
OML SAPI=62
BSC BTS
TEI 2
TEI 3
TEI 4
1.3.2 Layers of the Abis Interface
Physical Layer
The physical layer of the Abis interface uses PCM links with the rate of 2048 kbit/s. It provides32 channels with the rate of 64 kbit/s. The electrical parameter of the physical layer conforms to
the ITU-T G.703 recommendations.
The BSS is the connection point of radio channels and terrestrial channels. Each type ofchannels has its own transfer patterns and coding rates. The coding rate of the radio channels inthe BSS is 16 kbit/s while the rate of the channels on the Abis interface is 64 kbit/s. Therefore,
transcoding and rate adaptation functions are needed. Different multiplexing ratio modes, forexample, 10:1, 12:1, and 15:1, are used on the Abis interface to save transmission cost more
efficiently.
Data Link Layerz Overview
SAP is a data link connection endpoint is identified by a data link connection endpointidentifier as seen from layer 3 and by a data link connection identifier (DLCI) as seen fromthe data link layer.
The data link layer of the Abis interface uses the LAPD protocol. It uses the data
transmission services on the physical layer and provides connection-oriented orconnectionless services for layer 3. The data link layer provides services at the ServiceAccept Point (SAP), which is identified by a Service Access Point Identifier (SAPI).Seen
from layer 3, a data link connection endpoint is identified by a data link connection
-
7/30/2019 01-01 Signaling Fundmental
17/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-14 Huawei Technologies Proprietary Issue 02 (2007-06-30)
endpoint identifier. Seen from the data link layer, a data link connection endpoint isidentified by a data link connection identifier (DLCI). For the information exchangebetween two or more layer 3 entities, a connection must be established between the layer 3entities on the data link layer using a data link layer protocol.
The co-operation between data link layer entities is controlled by a peer-to-peer protocolspecific to the layer. The message units on the data link layer are transmitted between layer2 entities through the physical layer. Inter-layer service requests are processed throughservice primitives.
z Functions
The LAPD is used to transfer reliable end-to-end information between layer 3 entities byusing the D channel. Specifically, the LAPD supports:
Multiple terminal devices between MSs and physical interfaces
Multiple layer 3 entities
The LAPD performs the following functions:
Establishing one or several data links on the D channel
Delimiting, locating, and transmitting transparently frames so that a string of bitstransmitted on the D channel in the form of frames can be identified
Controlling and keeping the sequence of frames
Checking for transmission errors, format errors, and operation errors on data linkconnections
Correcting detected transmission errors, format errors, and operation errors
Notifying the management layer entities of unrecoverable errors
Performing flow control
The data link layer provides the means for information transfer between multiple combinations
of data link connection points. The information may be transferred through point-to-point datalink connections or broadcast data link connections.
Traffic Management Part of Layer 3
The traffic management part of the layer 3 on the Abis interface is described in GSM Rec. 08.58.
The procedures defined in these specifications have two major functions:
z Performing the interworking on the Um interface between an MS and the BSS or NSS
z Performing part of the radio resource management functions under the control of the BSC
Traffic management messages are classified into transparent and non-transparent messages.
z The transparent messages refer to the messages directly forwarded without interpretation
or being processed by the BTS.
z The non-transparent messages refer to the messages that are transmitted between the BSCand the BTS and that must be processed and structured by the BTS.
Traffic management messages can also be classified into four groups in terms of functions. The
four groups are as follows:
z Radio link layer management messages used to manage the data link layer on radiochannels
z Dedicated channel management messages used to manage dedicated channels such as theSDCCH and TCH
-
7/30/2019 01-01 Signaling Fundmental
18/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-15
z Common control channel management messages used to manage common controlchannels
z TRX management messages used to manage TRXs
The transparency and group of traffic management messages are determined by the message
discriminator at the header of the messages.
z Radio link management procedures
Radio link management procedures consist of the following:
Link establishment indication procedure: used by the BTS to indicate to the BSC that
an MS-originated multi-frame-mode link setup is successful. On receipt of theindication from the BTS, the BSC establishes an SCCP link to the MSC.
Link establishment request procedure: used by the BSC to request the establishment ofa multi-frame link on a radio channel
Link release indication procedure: used by the BTS to indicate to the BSC that anMS-initiated radio link release is complete
Link release request procedure: used by the BSC to request the release of a radio link
Transmission of a transparent RIL3 message on the Um interface in acknowledgedmode: used by the BSC to request the transmission of a transparent L3 message to anMS on the Um interface in acknowledged mode
Reception of a transparent RIL3 message on the Um interface in acknowledged mode:
used by the BTS to indicate to the BSC that a transparent L3 message is received on theUm interface in acknowledged mode
Transmission of a transparent RIL3 message on the Um interface in unacknowledgedmode: used by the BSC to request the transmission of a transparent L3 message to anMS on the Um interface in unacknowledged mode
Reception of a transparent RIL3 message on the Um interface in unacknowledged
mode: used by the BTS to indicate to the BSC that a transparent L3 message is receivedon the Um interface in unacknowledged mode
Link error indication procedure: used by the BTS to indicate to the BSC in case of anyerrors in the radio link layer.
z Dedicated channel management procedures
The dedicated channel management procedures consist of the following:
Channel activation procedure: used by the BSC to request the BTS to activate adedicated channel for an MS. The BSC later will assign the activated channel to the MSthrough an Immediate Assignment, Assignment Command, Additional Assignment, ora Handover Command message.
Channel mode modification procedure: used by the BSC to request the BTS to changethe mode of an activated channel
Handover detection procedure: used to detect the access of an MS being handed overon the Abis interface between the target BTS and the target BSC
Ciphering mode command procedure: used to start the ciphering procedure defined inGSM Rec. 04.08
Measurement report procedure: consists of the mandatory basic measurement reportprocedure and optional measurement report preprocessing procedure. The BTS reportsall the parameters related to handover decisions to the BSC through this procedure.
SACCH deactivation procedure: used by the BSC to deactivate the SACCH related to aTRX according to the Channel Release procedure defined in GSM Red. 04.08
-
7/30/2019 01-01 Signaling Fundmental
19/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-16 Huawei Technologies Proprietary Issue 02 (2007-06-30)
Radio channel release procedure: used by the BSC to release a radio channel that is nolonger needed
MS power control procedure: used by the BSS to control the transmit power of an MS
for which a channel is already activated. The power control decision must be
performed in the BSC. It can also be performed in the BTS. BTS transmit power control procedure: used by the BSS to control the transmit power
of a TRX with an activated channel. The BTS transmit power control decision must beperformed in the BSC. It can also be performed in the BTS.
Connection failure procedure: used by the BTS to indicate to the BSC that an activateddedicated channel is disconnected
Physical context request procedure: used by the BSC to obtain the information aboutthe "physical context" of a radio channel prior to a channel change. This is an opticalprocedure.
SACCH information modification procedure: used by the BSC to command the BTS tochange the information (system information) filled in on a specific SACCH
z Common channel management proceduresThe common channel management procedures consist of the following:
MS-initiated channel request procedure: triggered when a TRX detects a randomaccess from an MS (Channel Request message from the MS)
Paging procedure: used to page an MS on a specific paging sub-channel. Thisprocedure is used in an MS-terminated call procedure. It is initiated by the BSC after
receiving a Paging Command message from the MSC. The BSC determines the paginggroup to be used according to the IMSI of the called MS. The BSC sends the paginggroup number together with the identity of the MS to the BTS.
Immediate assignment procedure: used by the BSC to assign a dedicated channel for anMS immediately when the MS accesses the BTS
Delete indication procedure: used by the BTS to indicate to the BSC that an Immediate
Assign Command has been deleted due to AGCH overload
CCCH load indication procedure: used by the BTS to indicate to the BSC the load on aspecified CCCH if the load exceeds the preset threshold on the OMC. The indicationperiod is also set on the OMC.
Broadcast information modification procedure: used by the BSC to indicate to the BTSthe new system information to be broadcast on the BCCH
Short message cell broadcast procedure: used by the BSC to request short messageservice cell broadcast messages from the BTS
z TRX management procedures
The TRX management procedures consist of the following: SACCH filling information modify procedure: used by the BSC to indicate to the BTS
the new system information to be used as filling information on all downlink SACCHs
Radio resources indication procedure: used by the BTS to indicate to the BSC theinterference levels on the idle channels of a TRX
Flow control procedure: used by the Frame Unit Controller (FUC) in a TRX to informthe BSC of the TRX overload due to CCCH overload, AGCH overload, or TRXprocessor overload
Error reporting procedure: used by the BTS to inform the BSC of the detecteddownlink message errors, which cannot be reported through any other procedure
-
7/30/2019 01-01 Signaling Fundmental
20/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-17
OM Part of Layer 3z OM information model
Managed objects
There are four types of management objects: site, cell, carrier (TRX), and channel.Figure 1-7shows the basic structure of the managed objects.
Figure 1-7Basic structure of the managed objectsSite
Cell 0 Cell 1 Cell n
BTS TRX
Channel 7Channel 0 Channel 1
TRX 0 TRX 1 TRX m
Addressing of managed object
Network management messages are addressed through the classes and instances ofmanaged object. For each object instance in the BTS there is a complete L2 connection
description. The first established connection is assigned a semi-permanent orpermanent default TEI. The subsequent connections are assigned the TEIs provided by
the TEI setup procedure. Object instances can also use layer 3 addresses. The mixeduse of layer 2 addressing and layer 3 addressing enables one BTS site to have one ormultiple physical links.
States of managed objects
A managed object has three types of states: administrative state, operational state, andavailability status. SeeTable 1-2, Table 1-3, and Table 1-4for details.For a managedobject, the usage state further describes the operational state, and only the BSCcontrols the administrative state.
Table 1-2Administrative stateState Description
Locked The BSC has disconnected all the calls passing this managed object, and nonew services can be connected to this object.
Shut down No new services can be connected to this managed object, but ongoing callswill be maintained.
Unlocked New services can be connected to this managed object.
-
7/30/2019 01-01 Signaling Fundmental
21/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-18 Huawei Technologies Proprietary Issue 02 (2007-06-30)
Table 1-3Operational stateState Description
Disabled Resources are totally inoperable, and can no longer provide services for MSs.
Enabled Resources are partially or fully operable.
Table 1-4Availability statusState Description
ln test The resource is undergoing a test procedure. The operational state is
disabled.
Failed The resource has an internal fault that prevents it from operating The
operational state is disabled.
Power off The resource requires power to be applied and is not powered on. Theoperational state is disabled.
Off line The resource requires a routine operation to be performed to place it onlineand make it available for use. The operation may be manual or automatic,
or both. The operational state is disabled.
Dependency The resource cannot operate because some other resources on which it
depends is unavailable. The operational state is disabled.
Degraded The service available from the resource is degraded in some respect, such
as in speed or operating capacity.The operational state is enabled.
Not Installed The resource represented by the managed object is not present, or isincomplete. The operational state is disabled.
z Basic procedures
All procedures are based on formatted OM messages. Most formatted OM messagesinitiated by the BSC or BTS require the peer layer 3 to respond with a response or an
acknowledgment in the form of formatted OM messages. This pair of formatted OMmessages or a single formatted OM message that does not require a response is called abasic procedure.
All formatted OM messages are sent on layer 2 in the form of I frames. A group ofmessages, also called structured procedures, are based on the combination of some basicprocedures.
For a specific object instance, if a certain basic procedure is not complete, the system willnot start subsequent basic procedures. When there is no response to a formatted OM
message from the peer layer 3 upon L3 timer expiry, the basic procedure is regarded asnot completed. When there is no response (ACK or NACK) in the previous basicprocedure upon L3 timer expiry, then no subsequent basic procedure is sent to this objectinstance. The default value for L3 timer expiry is 10 seconds.
If part of an original message is not understood or supported, the entire message isdiscarded. An ACK message from an object instance indicates an affirm response. It isused to notify the message sender that the command has been executed or will be executed.
A NACK message from an object instance indicates a disaffirm response. It is used to
-
7/30/2019 01-01 Signaling Fundmental
22/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-19
notify the message sender of the unsuccessfully execution of the command and of thefailure cause.
The basic procedures are classified as follows:
Software loading management procedure
Abis interface management procedure
Transmission management procedure
Um interface management procedure
Test management procedure
State management and event reporting procedure
Equipment state management procedure
Other procedures
1.4 Um Interface1.4.1 Overview of the Um Interface
In a GSM network, an MS is connected through radio channels to a fixed part in the network sothat the MS can use communication services. For the purpose of interconnection between anMS and the BSS, it is necessary to standardize the transmission of the signals on the radio
channel. The specifications concerning the signal transmission on radio channels are calledradio interface, or Um interface.
The Um interface is specified by the following features:
z Channel structure and access capability
z MS-BSS protocols
z Operation and maintenance characteristics
z Performance characteristics
z Service characteristics
The Um interface is classified into three layers, as shown in Figure 1-8.
Figure 1-8Three layers of the Um interface
Layer 2 (L2)
Layer 1 (L1)
Layer 3 (L3)
The physical layer (L1) is the bottom layer. It defines the radio access capabilities of the GSM.It provides basic radio channels for information transfer on higher layers.The data link layer(L2) uses the LAPDm protocol. It defines various data transmission structures for controlling
data transmission.
-
7/30/2019 01-01 Signaling Fundmental
23/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-20 Huawei Technologies Proprietary Issue 02 (2007-06-30)
Layer 3 (shorted as L3 hereinafter in this document) is the highest layer. It processes variousmessages and procedures and controls services. L3 consists of three sub-layers: Radio Resourcemanagement (RR), Mobility Management (MM), and Connection Management (CM).
1.4.2 Physical LayerThe physical layer (L1) is the bottom layer of the Um interface. It provides physical links fortransmitting bit streams. It also provides for higher layers with various logical channels,
including traffic channels and signaling channels. Each logical channel has its own logicalaccess point.
Figure 1-9 shows the interfaces between L1 and L2, L1 and the radio resource management
sublayer (RR) of L3, L1 and other functional unit.
Figure 1-9Interfaces of L1Radio resource
management (L3)
L2
MPH
primitivePH
primitive
L1
TCH
Other functional units
L1 provides the following services:
z
Access capabilityL1 provides a series of limited logical channels for transmission service. Logical channelsare multiplexed on physical channels. Each TRX has eight physical channels. Through
data configuration, logical channels are mapped to physical channels.
z Error code detection
L1 provides error protection transmission, including error detection and correction.
z Ciphering
The BSS encrypts transmitted bit sequences based on a selected ciphering algorithm.
1.4.3 Data Link Layer
The purpose of the data link layer (L2) is to establish reliable dedicated data links between anMS and the BTS. The GSM system uses the LAPDm protocol on the L2 of the Um interface.This protocol evolves from the LAPD protocol.
L2 receives the services from L1 and provides services to L3 at service access points (SAPs).An SAP is identified by an SAPI. Each SAP is associated with one or multiple Data Link
Connection End Points (DLCEPs). Currently, two SAPI values, 0 (main signaling) and 3 (shortmessages), are defined in the LAPDm protocol.
The LAPDm used on the L2 of the Um interface is described here.
z Function
-
7/30/2019 01-01 Signaling Fundmental
24/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-21
The LAPDm transfers information between L3 entities through the Dm channel on the Uminterface. LAPDm supports multiple L3 entities and L1 entities, and signaling on BCCH,PCH, AGCH, and DCCH.
The Dm channel is a generic term for all the signaling channels on the Um interface in the GSM system.For instance, the Dm channel can be PCH or BCCH.
The LAPDm performs the following functions:
Providing one or more data link connections (DLCs) on the Dm channel. Each DLC isidentified by a data link connection identifier (DLCI).
Allowing frame type identification
Allowing L3 message units to be transparently transmitted between L3 entities
Performing sequence control to maintain the order of the frames transmitted a DLC
Detecting for format errors and operation errors on data links
Performing flow control
Establishing a contention resolution on a data link after an access request is detected on
the RACH
z Operation types
L2 transmits L3 information in unacknowledged and acknowledged modes. The twomodes can applied to one Dm channel.
Unacknowledged mode
In unacknowledged mode, L2 transmits L3 information in Unnumbered Information
(UI) frames. It does not acknowledge the transmitted UI frames or perform flowcontrol or error correction. The unacknowledged mode is applicable to different typesof control channels except the RACH.
Acknowledged mode
In acknowledged mode, L2 transmits L3 information in numbered Information (I)frames. It acknowledges the transmitted I frames. It performs error correction byresending unacknowledged frames. When L2 fails to correct errors, it informs the
specific L3 entity of the correction failure. Flow control procedures are also defined.The acknowledged mode is applicable to the DCCH.
z Information transmission mode
Information is transmitted in different modes on different channels.
Information transfer on the BCCH: The BCCH directional and used by the BTS tobroadcast system information to MSs. Only the acknowledged mode can be used on theBCCH.
Information transfer on the PCH+AGCH: These channels are only used by the BTS to
transfer information to MSs. Only the unacknowledged mode is applicable to thePCH+AGCH.
Information transfer on the DCCH: Either the acknowledged or the unacknowledgedmode can be used. L3 can choose the specific mode at a certain time.
z Release of data links
The data links in multi-frame mode are released as follows:
Normal release: by exchange of commands/responses
Local end release, that is, without exchange of commands/responses, initiated andcontrolled by L3
-
7/30/2019 01-01 Signaling Fundmental
25/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-22 Huawei Technologies Proprietary Issue 02 (2007-06-30)
1.4.4 Layer 3
Overview of Layer 3
The layer 3 (L3) of the Um interface provides the functions to establish, maintain, and terminatecircuit-switched connections across a GSM PLMN and other networks to which the GSMPLMN is connected.
The L3 entity consists of many functional program blocks. These program blocks transmit
message units carrying various kinds of information between all L3 entities and between L3and its neighboring layers.
L3 consists of the following three sub-layers:
z Connection Management (CM)
z Mobility Management (MM)
z Radio Resource management (RR)
The CM sub-layer (the highest sub-layer) consists of three functional entities:
z Call Control (CC)
z Short Message Service (SMS)
z Supplementary Service (SS)
In total, the L3 on the Um interface has five functional entities, which performs the followingfunctions accordingly:
z Establishes, operates, and releases dedicated channels (RR)
z Performs location updating, authentication, and TMSI reallocation (MM)
z Establishes, maintains, and terminates circuit-switched calls (CC)z Supports supplementary services (SS)
z Supports short messages service (SMS)
The signaling L3 protocols between the MSs and the network (BSS) perform the functions of
L3. Here the functions of different entities in the BSS are not taken into consideration. Thefunctions of L3 and its supporting lower layers, therefore, provide the Mobile Network
Signaling (MNS) service to the upper layers.
The service interfaces between L3 and higher layers and the interactions between the neighbor
neighboring sub-layers in L3 can be described in primitives and parameters. The three
sub-layers of L3 perform the information exchange between peer entities.
Functions of Layer 3
The L3 functions through its five functional entities. The five functional entities perform the
following functions:
z Radio Resource management (RR)
Establishing, maintaining, and releasing physical channels and logical channels
Performing inter-cell connection upon the request from the CM sub-layer
z Mobility Management (MM)
Performing MS-specific functions and notifying the network when an MS is activated
and deactivated, or the when location area of an MS changes
-
7/30/2019 01-01 Signaling Fundmental
26/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Issue 02 (2007-06-30) Huawei Technologies Proprietary 1-23
Responsible for the security of activated radio channels
z CC: performing all necessary functions to establish or release CS connections
z SS: performing all necessary functions to support GSM supplementary services
z SMS: performing all necessary functions to support point-to-point GSM short message
services
In addition to the previous functions, L3 performs functions related to the transmission ofmessages, for example, multiplexing and splitting. These functions are defined in the protocols
related to RR and MM.
The L3 routes messages according to the protocol discriminator (PD) and transaction identifier(TI), which are part of the message header.
The routing function of the MM enables the MM to route the messages of the CM entities andthe messages of the MM entity to the RR service access point (RR-SAP), and to multiplex the
messages in case of concurrent transactions.
The routing function of the RR distributes the to-be-sent messages according to their PD andthe actual channel configuration.
The routing function of the RR distributes the messages from different service access points of
L2 based on the PD. If a message belongs to the RR sub-layer, this message will be transmittedto the RR entity based on the TI.The other messages are sent to the MM sub-layer through theRR-SAP. If a message belongs to the MM sub-layer, the message will be transmitted to the MMentity based on the TI. The other messages are sent to the CM sub-layer through the MM-SAPs,
and then sent to the CM entities.
Figure 1-10 shows the L3 protocol model of the Um interface.
-
7/30/2019 01-01 Signaling Fundmental
27/28
1 Signaling Fundamentals
M900/M1800 Base Station Subsystem
Signaling Analysis Manual
1-24 Huawei Technologies Proprietary Issue 02 (2007-06-30)
Figure 1-10L3 protocol model of the Um interface
C
C
MNCC-SAP
S
S
MNSS-SAP
SM
S
MNSMS-SAP
MNS
MMREG-SAP
MMCC-SAP
MMSS-SAP
MMSMS-SAP
MM CC SS SMSMM
RR-SAP
..RR
RR
PD
RR
SAPI 0 SAPI 3
RACCH
SDCCH
SACCH
FACCH
BCCH
SDCCH
SACCH
AGCH+PCH
L3s
ignaling
The RR sub-layer at the bottom receives the services from L2 through various service accesspoints (that is, various types of channels) of L2, and provides services to the MM sub-layerthrough RR-SAP.
The MM sub-layer provides services to different entities through different SAPs:
z To the CC through MMCC-SAP
z To the SS through MMSS-SAP
z To the SMS through MMSMS-SAP
z To the high layer through MMREG-SAP
The three independent entities (CC, SS, and SMS) of the CM sub-layer provide services tohigher layers through MNCC-SAP, MNSS-SAP, and MNSMS-SAP respectively.
Service Characteristics of L3z Services provided by L3 on the MS side
Registration services, that is, IMSI attach and detach
-
7/30/2019 01-01 Signaling Fundmental
28/28
M900/M1800 Base Station Subsystem
Signaling Analysis Manual 1 Signaling Fundamentals
Call control services, including normal establishment of MS-originating calls,emergency establishment of MS-originating calls, call hold, call termination, andsupport for call-related supplementary services
Support for call independent supplementary services
Support for short messages service
z Services provided by L3 on the network side
Call control services, including call establishment, call hold, call termination, andsupport for call-related supplementary services
Support for call independent supplementary services
Support for short messages service
z Inter-layer services between an MS and the network
For the services provided by the RR, refer to Figure 1-11. These services are provided
to the MM through RR-SAP. They are used to set up control channel connections andtraffic channel connection, indicate ciphering mode, release control channel
connections, and transmit control data. For the services provided by the MM, refer to Figure 1-12. These services are used to
manage the three entities (CC, SS, and SMS) of the CM sub-layer.
Figure 1-11Communications between RR sub-layers
RR-SAP
MS side Network side
MM
RR
RR-primitive
Protocols between
RR sub-layers
Figure 1-12Communications between MM sub-layers
CC SMSSS
MS side
MM
CC SMSSS
Network side
MM
Protocols between
MM sub-layers