xhd6801+_converter_ed_d_175-000517-00
TRANSCRIPT
Installation and Operation Manual
XHD6801+Broadcast Quality Up/Cross/Downconverter
Edition D175-000517-00
Edition DSeptember 2011
XHD6801+Broadcast-Quality Up/Cross/Downconverter
Installation and Operation Manual
Copyright InformationCopyright 2010-2011 Harris Corporation, 1025 West NASA Boulevard, Melbourne, Florida 32919-0001 U.S.A.
All rights reserved. This product and related documentation are protected by copyright and are distributed under licenses restricting their use, copying, distribution, and decompilation. No part of this product or related documentation may be reproduced in any form by any means without prior written authorization of Harris Corporation and its licensors, if any.
This publication could include technical inaccuracies or typographical errors. Changes are periodically added to the information herein; these changes will be incorporated into new editions of the publication. Harris Corporation may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time.
All trademarks are property of their respective owners.
Warranty InformationThe Limited Warranty Policy provides a complete description of your warranty coverage, limitations, and exclusions, as well as procedures for obtaining warranty service. To view the complete warranty, visit our website.
This publication is provided “as is” without warranty of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability, fitness for a particular purpose, or non-infringement.
Contents
PrefaceManual Information .............................................................................. vii
Unpacking/Shipping Information .......................................................... ix
Restriction on Hazardous Substances (RoHS) Compliance ....................x
Waste from Electrical and Electronic Equipment (WEEE) Compliance xi
Safety .................................................................................................... xii
Chapter 1: IntroductionOverview ..................................................................................................1
Product Description ..................................................................................2
Main Features ...................................................................................2
Software Key Options .......................................................................4
Applications ......................................................................................5
Module Description ..................................................................................6
Front Module ....................................................................................6
Back Module .....................................................................................8
Signal Flow .....................................................................................10
Chapter 2: InstallationOverview ................................................................................................11
Maximum 6800+ Frame Power Ratings ................................................12
Unpacking the Module ...........................................................................13
Preparing the Product for Installation .............................................13
Checking the Packing List ..............................................................13
Setting Jumpers ......................................................................................14
Installing XHD6801+ Modules .............................................................17
XHD6801+ License Keys ......................................................................17
XHD6801+ Installation and Operation Manual iii
Contents
Upgrading Module Firmware ................................................................ 18
Upgrading the Firmware ................................................................ 18
Correcting a Failed Upgrading Procedure ..................................... 21
Chapter 3: Configuration and OperationOverview ............................................................................................... 25
Operating Notes ..................................................................................... 26
Video Processing Modes ....................................................................... 27
Mode 1: Scaled Outputs with Re-clocked Inputs ........................... 27
Mode 2: Frame Sync and Scalar Outputs ....................................... 28
Mode 3: Discrete Frame Sync and Scalar Outputs ........................ 30
Q-SEE Compliant Thumbnails .............................................................. 30
Changing Parameter Settings ................................................................ 32
Changing Parameters Using CCS Software ................................... 32
Changing Parameter Settings Using Card-Edge Controls ............. 33
Enabling On-Screen Display .......................................................... 35
Recalling Default Parameter Settings ............................................ 35
Reading Software and Hardware Versions .................................... 35
Entering License Keys .......................................................................... 36
Aspect Ratio Processing ........................................................................ 37
Enhanced Aspect Ratio Conversion Control ................................. 37
Enhanced AFD/WSS/VI Insertion ................................................. 37
Selecting a Standard Aspect Ratio ................................................. 38
Selecting a Custom Aspect Ratio ................................................... 39
Selecting Aspect Ratio Control Following AFD, VI, WSS ........... 39
Setting a Custom Aspect Ratio ...................................................... 40
Active Format Description .................................................................... 40
AFD/ARC Alignment .................................................................... 40
AFD, VI, and WSS Detection ........................................................ 42
AFD, VI and WSS Code Insertion ................................................. 43
AFD, VI, WSS Based Aspect Ratio Control ................................. 44
AFD, VI, WSS Custom Mapping Configuration ........................... 44
Advanced Controls ......................................................................... 44
AFD Descriptions .......................................................................... 45
Closed Captioning and DVB Teletext Captioning ................................ 52
Setting Closed Captioning and Teletext ......................................... 52
Audio Configuration ............................................................................. 53
Audio Controls ............................................................................... 53
iv XHD6801+ Installation and Operation Manual
Contents
Audio Routing .................................................................................53
Audio Proc Amp .............................................................................54
Audio Status Parameters .................................................................55
GPI .........................................................................................................56
GPI Input .........................................................................................56
GPI Output ......................................................................................56
Video Keying .........................................................................................56
Chapter 4: Parameters, LEDs, and AlarmsOverview ................................................................................................57
Control Parameters .................................................................................58
On Screen Display Monitoring .......................................................58
LEDs and Alarms ...................................................................................59
LEDs ...............................................................................................59
Alarms .............................................................................................61
Chapter 5: SpecificationsOverview ................................................................................................63
Inputs ......................................................................................................64
SD/HD-SDI Video ..........................................................................64
Genlock ...........................................................................................65
Outputs ...................................................................................................66
SDI Video Outputs ..........................................................................66
Miscellaneous .........................................................................................67
Audio Delay (Data Out) ..................................................................67
Performance ....................................................................................67
Propagation Delays .........................................................................67
Appendix A: Communication and Control Troubleshooting Tips
Overview ................................................................................................69
Software Communication Problems ......................................................70
Hardware Communication Problems .....................................................73
IndexKeywords ...............................................................................................75
XHD6801+ Installation and Operation Manual v
Contents
vi XHD6801+ Installation and Operation Manual
Preface
Manual Information
PurposeThis manual details the features, installation, operation, maintenance, and specifications for the XHD6801+ broadcast-quality up/cross/down- converter.
AudienceThis manual is written for engineers, technicians, and operators responsible for installation, setup, maintenance, and/or operation of the XHD6801+ broadcast-quality up/cross/downconverter.
Revision HistoryTable P-1. Revision History of Manual
Edition Date Comments
A June 2008 Initial release
B August 2009 Addition of propagation delay specs, miscellaneous corrections
C March 2010 Addition of ARC and GPI improvements
D September 2011 Addition of a third video processing mode
XHD6801+ Installation and Operation Manual vii
Preface
Writing ConventionsTo enhance your understanding, the authors of this manual have adhered to the following text conventions:
Obtaining DocumentsProduct support documents can be viewed or downloaded from our Web site. Alternatively, contact your Customer Service representative to request a document.
Table P-2. Writing Conventions
Term or Convention
Description
Bold Indicates dialog boxes, property sheets, fields, buttons, check boxes, list boxes, combo boxes, menus, submenus, windows, lists, and selection names
Italics Indicates E-mail addresses, the names of books or publications, and the first instances of new terms and specialized words that need emphasis
CAPS Indicates a specific key on the keyboard, such as ENTER, TAB, CTRL, ALT, or DELETE
Code Indicates variables or command-line entries, such as a DOS entry or something you type into a field
> Indicates the direction of navigation through a hierarchy of menus and windows
hyperlink Indicates a jump to another location within the electronic document or elsewhere
Internet address Indicates a jump to a website or URL
NoteIndicates important information that helps to avoid and troubleshoot problems
viii XHD6801+ Installation and Operation Manual
Preface
Unpacking/Shipping Information
Unpacking a ProductThis product was carefully inspected, tested, and calibrated before shipment to ensure years of stable and trouble-free service.
1. Check equipment for any visible damage that may have occurred during transit.
2. Confirm that you have received all items listed on the packing list.
3. Contact your dealer if any item on the packing list is missing.
4. Contact the carrier if any item is damaged.
5. Remove all packaging material from the product and its associated components before you install the unit.
Keep at least one set of original packaging, in the event that you need to return a product for servicing.
Product ServicingExcept for firmware upgrades, XHD6801+ modules are not designed for field servicing. All hardware upgrades, modifications, or repairs require you to return the modules to the Customer Service center.
Returning a ProductIn the unlikely event that your product fails to operate properly, please contact Customer Service to obtain a Return Authorization (RA) number, then send the unit back for servicing.
Keep at least one set of original packaging in the event that a product needs to be returned for service. If the original package is not available, you can supply your own packaging as long as it meets the following criteria:
• The packaging must be able to withstand the product’s weight.
• The product must be held rigid within the packaging.
• There must be at least 2 in. (5 cm) of space between the product and the container.
• The corners of the product must be protected.
Ship products back to us for servicing prepaid and, if possible, in the original packaging material. If the product is still within the warranty period, we will return the product prepaid after servicing.
XHD6801+ Installation and Operation Manual ix
Preface
Restriction on Hazardous Substances (RoHS) Compliance
Directive 2002/95/EC—commonly known as the European Union (EU) Restriction on Hazardous Substances (RoHS)—sets limits on the use of certain substances found in electrical and electronic equipment. The intent of this legislation is to reduce the amount of hazardous chemicals that may leach out of landfill sites or otherwise contaminate the environment during end-of-life recycling. The Directive, which took effect on July 1, 2006, refers to the following hazardous substances:
• Lead (Pb)
• Mercury (Hg)
• Cadmium (Cd)
• Hexavalent Chromium (Cr-V1)
• Polybrominated Biphenyls (PBB)
• Polybrominated Diphenyl Ethers (PBDE)
According to this EU Directive, all products sold in the European Union will be fully RoHS-compliant and “lead-free.” (See our website for more information.) Spare parts supplied for the repair and upgrade of equipment sold before July 1, 2006 are exempt from the legislation. Equipment that complies with the EU directive is marked with a RoHS-compliant emblem, as shown in Figure P-1.
Figure P-1. RoHS Compliance Emblem
x XHD6801+ Installation and Operation Manual
Preface
Waste from Electrical and Electronic Equipment (WEEE) Compliance
The European Union (EU) Directive 2002/96/EC on Waste from Electrical and Electronic Equipment (WEEE) deals with the collection, treatment, recovery, and recycling of electrical and electronic waste products. The objective of the WEEE Directive is to assign the responsibility for the disposal of associated hazardous waste to either the producers or users of these products. As of August 13, 2005, producers or users are required to recycle electrical and electronic equipment at end of its useful life, and may not dispose of the equipment in landfills or by using other unapproved methods. (Some EU member states may have different deadlines.)
In accordance with this EU Directive, companies selling electric or electronic devices in the EU are affixing labels that indicate such products must be properly recycled. (See our website for more information.) Contact your local sales representative for information on returning these products for recycling. Equipment that complies with the EU directive is marked with a WEEE-compliant emblem, as shown in Figure P-2.
Figure P-2. WEEE Compliance Emblem
XHD6801+ Installation and Operation Manual xi
Preface
SafetyCarefully review all safety precautions to avoid injury and prevent damage to this product or any products connected to it. If this product is rack-mountable, it should be mounted in an appropriate rack using the rack-mounting positions and rear support guides provided. It is recommended that each frame be connected to a separate electrical circuit for protection against circuit overloading. If this product relies on forced air cooling, it is recommended that all obstructions to the air flow be removed prior to mounting the frame in the rack.
If this product has a provision for external earth grounding, it is recommended that the frame be grounded to earth via the protective earth ground on the rear panel.
IMPORTANT! Only qualified personnel should perform service procedures.
Safety Terms and Symbols in this Manual
WARNINGStatements identifying conditions or practices that may result in personal injury or loss of life. High voltage is present.
CAUTIONStatements identifying conditions or practices that can result in damage to the equipment or other property.
xii XHD6801+ Installation and Operation Manual
Chapter 1
Introduction
OverviewXHD6801+ modules offer broadcast-quality HD/SD-SDI upconversion, crossconversion, and downconversion with aspect ratio conversion (ARC), and closed-captioning support. There are three basic varieties available:
• XHD6801+UCT up/crossconverter
• XHD6801+DT downconverter
• XHD6801+UCDT up/cross/down converter
XHD6801+UC and XHD6801+D and can be upgraded in the field to full up/cross/down converter functionality.
This chapter includes the following topics:
• “Product Description” on page 2
• “Module Description” on page 6
Note
XHD6801+ modules must be installed in frames with fans. FR6802+DM and 6800/7000 series frames also do not support these products.
XHD6801+ Installation and Operation Manual 1
Chapter 1: Introduction
Product DescriptionXHD6801+ modules provide conversion between SD-SDI and HD-SDI video. They include aspect ratio conversion (ARC) capabilities, and can accept both embedded audio and ANC data.
The SDI input has error monitoring capabilities in the SD mode (EDH) and in HD mode (CRC), and supports external or midplane genlock sources.
You can control XHD6801+ modules using card-edge controls and CCS-enabled hardware and software control products.
Additionally, you can use SNMP control systems and HTTP (Internet) browsers if you purchase the required licenses. Contact your Customer Service representative for more details.
Main FeaturesXHD6801+ features include the following:
• Upconversion of SD-SDI video to broadcast-quality HD-SDI video (XHD6801+UCT and XHD6801+UCDT)
• Crossconversion of HD-SDI video (XHD6801+UCT and XHD6801+UCDT)
• Downconversion of HD-SDI video to SD-SDI video (XHD6801+DT and XHD6801+UCDT)
• Inputs
• Auto-sensing HD/SD-SDI input with embedded audio data, error monitoring, VANC data such as WSS/VI/AFD and optional closed captioning and teletext
• Analog composite genlock input with support for tri- and bi-level sync
2 XHD6801+ Installation and Operation Manual
Chapter 1: Introduction
• Outputs
• Four equalized and reclocked HD/SD-SDI outputs of the SDI input that can be configured to be frame synchronized
• Two HD/SD-SDI outputs carrying the converted program signal with:
• Embedded audio
• Video Ancillary Data Space (VANC) data, including Wide Screen Signalling (WSS), Video Index (VI), and Active Format Description (AFD)
• Closed captioning and teletext capabilities
• Two configurable HD/SD-SDI outputs carrying either the converted program signal or the key or monitor signal (with OSD for displaying control parameter settings)
• User-selectable input/output standards and formats
• Video Processing
• 10-bit up-, down-, cross-, and aspect ratio conversion with motion adaptive de-interlacing
• Color-space conversion between SD-SDI (601) and HD-SDI (709)
• User-configurable aspect ratio conversion (H/V size and position) for picture resizing, with eight selectable internally-generated color ARC backgrounds
• Variable aspect ratio conversion with five user presets and fixed preset aspect ratios that include 16:9 anamorphic, 16:9 middle cut, 14:9, 4:3, and pixel true
• Aspect ratio adjustment according to embedded WSS/VI/AFD information
• User-selectable video frame delay of up to 12 frames
• Clean cut transition during aspect ratio change
XHD6801+ Installation and Operation Manual 3
Chapter 1: Introduction
• ANC Processing
• Enhanced WSS, VI, and AFD decoding, processing, and encoding capabilities
• Automatic correction of AFD codes if incoming AFD information is incorrect
• Fully-configurable AFD/VI/WW embedding on AFD loss
• 24-bit audio processing
• Embedded audio processing (demultiplexing from SDI, delay/sync, sample rate conversion, and remultiplexing into SDI)
• Support for 4 groups (16 channels) of embedded audio
• Support for compressed and linear PCM audio data in the same audio group
• Mono level swapping of audio channels
• Handling of any embedded compressed audio with fixed delay
• Audio delay that matches video propagation plus additional user delay of up to 1.2 seconds
• Store and recall of ARC presets through SNMP and CCS-enabled hardware and software controls
• Loss of video (LOV) modes, including pass, freeze, and black
• Built-in HD/SD-SDI test generator containing white, black, frequency sweep, cross-hatch pattern, color bars signal, and Safe Area Graticles (SAG) key
• Support for Q-SEE compliant thumbnails when installed in a FR6802+QXF frame
• Soft edge rectangle key output of non-picture area
Software Key OptionsThe following software option keys are available:
• XHD68+D-UG-UCD software key converts a XHD6801+DT to a full XHD6801+UCDT up/cross/down converter.
• XHD68+UC-UG-UCD software key converts a XHD6801+UCT to a full XHD6801+UCDT up/cross/down converter.
4 XHD6801+ Installation and Operation Manual
Chapter 1: Introduction
ApplicationsThe XHD6801+ modules are suitable for the following applications:
• Final conversion to a high- or standard-definition output, regardless of input format
• Bridging between high-definition and standard-definition installations in a mixed signal facility
• Bridging between 720p and 1080p high-definition installations
• Transitioning small market broadcasters requiring high-quality conversion
• Ingestion of high-definition or standard-definition signal into a facility running either video standard
XHD6801+ Installation and Operation Manual 5
Chapter 1: Introduction
Module Description
Front ModuleFigure 1-1 shows the position of the LEDs and module controls on the front of the XHD6801+ modules.
Figure 1-1. XHD6801+ Module
Table 1-1 on page 7 briefly describes generic 6800+ LEDs, switches, and jumpers.
Status LED
Mode select rotary switch
Navigation toggle switch
Monitoring LEDs
Remote/local control jumper
Extractor handle
Control LEDs
6 XHD6801+ Installation and Operation Manual
Chapter 1: Introduction
Table 1-1. Generic 6800+Module Features
Feature Description
Status LED Various color and lighting combinations of these LEDs indicate the module’s state and activities. See “LEDs and Alarms” on page 59 for more information.
Mode select rotary switch
This switch selects between various control and feedback parameters.
Navigation toggle switch
This switch navigates up and down through the available control parameters:
• Down: Moves down through the parameters
• Up: Moves up through the parameters
Control LEDs Various lighting combinations of these Control LEDs (sometimes referred to as “Bank Select LEDs”) indicate the currently selected bank. See “Bank Select LEDs” on page 34 for more information.
Monitoring LEDs
Each 6800+ module uses LEDs to indicate varying states and functions. See page 59 for details.
Local/remote control jumper
• Local: Locks out external control panels and allows card-edge control only; limits the functionality of remote software applications to monitoring
• Remote: Allows remote or local (card-edge) configuration, operation, and monitoring of the XHD6801+
See page 14 for more information on jumpers.
XHD6801+ Installation and Operation Manual 7
Chapter 1: Introduction
Back Module
Figure 1-2. XHD6801+ Back Module
Figure 1-3. GPI In/Out Pinouts
GPI I/O
SDI IN 1
SDI PROGRAM OUT
SDI MONITOR OUT
SDI RECLOCKED OUTAUD DELAY/6 Hz
REF IN
8
GPI 1
1
GND
GPI 2 GPI 3
GPI 4 GND GPO 1 GPO 2
8 XHD6801+ Installation and Operation Manual
Chapter 1: Introduction
Table 1-2 describes each back module connector.
Table 1-2. Back Module Connector Descriptions
Back Module Label Description
SDI In Inputs HD/SD-SDI video for up, down, or cross-conversion or reclocking; HD/SD-SDI signals can also be input for reclocking.
SDI DA Out (4) Outputs SD or HD reclocked video output signals; video from these outputs by-passes the module’s scalar processor; configurable for either reclocked or frame sync outputs
SDI Program Out (2) Outputs HD/SD-SDI converted video
Audio Delay / 6 HZ Outputs the output audio delay signal
SDI Program/Monitor Out (2)
Outputs a program signal for monitoring purposes; an on-screen display of XHD6801+ control parameters can be enabled on these outputs
Reference In Inputs a bi-level (NTSC/PAL-B) or tri-level sync (1080i/1080p) external video reference source that can be internally terminated using a jumper (see page 65 for the video standards supported)
GPI In/Out Provides four GPI inputs and two GPI outputs for automation (these are open collector style inputs with approximately 10 K pull-ups to +5V that can use “contact closure-to-ground” switches)
XHD6801+ Installation and Operation Manual 9
Chapter 1: Introduction
Signal Flow
Figure 1-4. XHD6801+ Signal Flow Diagram
Reference in
Frame reference
Genlock
Equalizer
Closed captioning
demux
AFD/WSS/VI
detection
Videosync/delay
Buffer
Audio proc
Audio sync/delay
Audiode-mux
On screen display
Thumbnail streaming
Horizontal & vertical resizer
Audio/AFD/VI/WSS/CC embedder
Motion adapt de-interlacer
Video test generator
HD/SD-SDI w/audio in
HD/SD-SDI reclocked out 1
HD/SD-SDI reclocked out 2
HD/SD-SDI reclocked out 3
HD/SD-SDI reclocked out 4
Thumbnails
HD/SD-SDI prog. out 1
HD/SD-SDI prog. out 2
HD/SD-SDI monitor/program out 2
HD/SD-SDI monitor/program out 1
Video proc
CPU Monitoring and
Control
10 XHD6801+ Installation and Operation Manual
Chapter 2
Installation
OverviewThis chapter describes the XHD6801+ installation process, including the following topics:
• “Maximum 6800+ Frame Power Ratings” on page 12
• “Unpacking the Module” on page 13
• “Setting Jumpers” on page 14
• “Installing XHD6801+ Modules” on page 17
• “XHD6801+ License Keys” on page 17
• “Upgrading Module Firmware” on page 18
Caution
Before installing this product, read the 6800+ Series Safety Instructions and Standards Manual shipped with every frame installation and operation manual. This information is also available on our website. The safety manual contains important information about the safe installation and operation of 6800+ series products.
See your frame installation and operation manual for information about installing and operating an FR6802+ frame and its components.
XHD6801+ Installation and Operation Manual 11
Chapter 2: Installation
Maximum 6800+ Frame Power RatingsThe power consumption for one XHD6801+ module is 17.5 W. Table 2-1 shows the maximum allowable power ratings for 6800+ series frames. Note the given maximums before installing any 6800+ modules in your frame.
Due to high levels of heat dissipation, XHD6801+ modules should not be installed in frames without fans. The modules cannot be installed in FR6802+DM and 6800/7000 series frames.
Note
To maintain proper temperatures, ensure that the front panel is closed at all times, and that the fan module is fully operational.
* Each front module requires three slots.
** Although XHD6801+ modules require more than 15.75 Watts over three slots, the actual consumption is considered acceptable if no more than 5 modules are installed.
Caution
Heat sinks on the XHD6801+ require extra clearance. To prevent damage to components, ensure that you do not insert the front module in slots 6, 14, 19, or 20.
Table 2-1. Maximum Power Ratings for 6800+ Frames
6800+ Frame TypeMax. Frame Power Dissipation
Max. Number of XHD6801+ Modules
Max Power Dissipation for Three Slots*
FR6802+QXF(frame with AC or DC power supply)
120 W 6 18 W
FR6802+XF(frame with AC power supply)
120 W 6 18 W
FR6802+XF48(frame with DC power supply)
105 W 5 15.75 W**
FR6822+/ FR6822+QXFE 120 W 6 18 W
12 XHD6801+ Installation and Operation Manual
Chapter 2: Installation
Unpacking the Module
Preparing the Product for InstallationBefore you install the XHD6801+, perform the following:
• Check the equipment for any visible damage that may have occurred during transit.
• Confirm receipt of all items on the packing list. See “Checking the Packing List” below for more information.
NoteContact your Customer Service representative if parts are missing or damaged.
• Remove the anti-static shipping pouch, if present, and all other packaging material.
• Retain the original packaging materials for possible re-use.
See “Unpacking/Shipping Information” on page ix for information about returning a product for servicing.
Checking the Packing List
Table 2-2. Available Product Packages
Ordered Product Content Description
• XHD6801+UC up/crossconverter
• XHD6801+D downconverter
• XHD6801+UCD up/cross/downconverter
• One front module
• One back module
• One XHD6801+ Broadcast-Quality Up/Cross/Downconverter Installation and Operation Manual
XHD6801+ Installation and Operation Manual 13
Chapter 2: Installation
Setting JumpersThe XHD6801+ module has the following jumper settings:
• “Local/Remote Jumper” on page 14
• “External Reference Termination Jumper” on page 15
• “Input/Output Audio Delay/6 Hz Jumper” on page 16
Figure 2-1 shows the location of the jumpers.
Figure 2-1. XHD6800+ Jumpers
Local/Remote Jumper
Follow this procedure to set the LOC/REM jumper for either local or remote control:
1. Locate the LOC/REM control jumper on the module (beside the mode select rotary switch). Figure 2-1 on page 14 shows the standard location of the LOC/REM jumper.
Local/Remote jumper
Jumper J3 Input/Output Audio Delay/6 Hz
Jumper J1External reference termination
14 XHD6801+ Installation and Operation Manual
Chapter 2: Installation
2. Place a jumper on pins 1 and 2 to set the module for Remote control, or pins 2 and 3 to set the module for Local control. See Figure 2-2.
Figure 2-2. Remote/Local Control Settings
Note
You must configure modules for local or remote operation prior to power-up. To change the configuration, first remove power from the module, reset the jumper, and then reapply power. The white triangle near the jumper pins on the module indicates pin 1.
See Table 1-1 on page 7 for more information on local/remote control jumper functionality.
External Reference Termination Jumper
Follow this procedure to set the external Reference Input Termination jumper:
1. Locate jumper J1 on the module.
(Figure 2-1 on page 14 shows the location of the jumper.)
2. Place a jumper on pins 1 and 2 to set the module for 75 Termination, or pins 2 and 3 for No Termination (see Figure 2-3).
Figure 2-3. Genlock Termination Settings
1 2 3 1 2 3
Remote control Local control
No Termination75 Termination
1 2 3 1 2 3
XHD6801+ Installation and Operation Manual 15
Chapter 2: Installation
Input/Output Audio Delay/6 Hz Jumper
Follow this procedure to set the Input/Output Audio Delay/6 Hz jumper:
1. Locate jumper J3 on the module.
(Figure 2-1 on page 14 shows the location of the jumper.)
2. Place a jumper on pins 1 and 2 to set the module for 6 Hz input, or pins 2 and 3 to set input/output audio delay output (see Figure 2-3).
Figure 2-4. Genlock Termination Settings
1 2 3 1 2 3
6 Hz I/O audio delay output
16 XHD6801+ Installation and Operation Manual
Chapter 2: Installation
Installing XHD6801+ ModulesXHD6801+ products have triple-width back modules. These products cannot be installed in frames without fans, or in FR6802+DM and 6800/7000 series frames.
See the FR6802+ Frames Installation and Operation Manual for information about installing and operating an FR6802+ frame and its components.
XHD6801+ License KeysTable 2-3 lists the available XHD6801+ feature upgrade license keys.
To enter a license key, you must use a NUCLEUS control panel, or a CCS software application, such as CCS + Pilot Lite, Pilot, or Navigator. See page 36 for information about entering license keys.
Table 2-3. Available License Keys
License Key Order Number Feature Upgrade
XHD6801+D-UCD Downconverter upgraded to full up/cross/downconversion capability
XHD6801+UC-UCD Up/crossconverter upgraded to full up/cross/downconversion capability
XHD6801+ Installation and Operation Manual 17
Chapter 2: Installation
Upgrading Module FirmwareFirmware upgrading is a routine procedure that you must perform to install newer versions of software on 6800+ modules. CCS Pilot, Co-Pilot, or Navigator software version 3.1.1 or later is required for this procedure. The frame must contain or be connected to another frame that contains an ICE6800+ or a 6800+ETH module. During the upgrade procedure, the affected modules are automatically rebooted.
In the unlikely event that the upgrade fails (because of such situations as network interruptions, power failures, etc.), the module may not respond to controls and will appear to be non-functional. In that event, follow the procedures described in “Correcting a Failed Upgrading Procedure” on page 21.
Upgrading the FirmwareYou can upgrade your 6800+ module’s firmware using the Software Upgrade tool. This tool is included with CCS Pilot, Co-Pilot, or Navigator software version 3.1.1 or later.
Caution
The File Transfer tab is not meant to be used for firmware upgrades. Use the Software Upgrade tool to upgrade module firmware.
To upgrade your module’s firmware, follow these steps:
1. Download the most recent appropriate upgrade package from our website or from your CD-ROM.
2. If the affected module has not been discovered, perform the Discovery operation.
NoteYou can find information about discovering modules in your CCS software application manual or online help. (If you cannot discover the device, see “Manually Adding a Device to the Discovery or Network Folder” on page 22.)
18 XHD6801+ Installation and Operation Manual
Chapter 2: Installation
3. From the Tools menu, select Software Upgrade.
The Software Upgrade window opens or is brought to the foreground.
Figure 2-5. Software Upgrade Tool’s New Transfer Tab
4. On the New Transfer tab, click Add.
The Device Selection dialog box opens.
5. Select one or more devices, and then click OK to close the Add Device dialog box.
NoteYou can only add one device from each IP address. All items in a frame have the same IP address.
The selected devices appear in the table under Device Name. These devices will receive the same upgrade package.
6. Before proceeding with the firmware upgrade, you can—
• Highlight the module’s position in the Navigation window by clicking Find Device.
Package Info includes a list of the components contained in the ZIP file.
Version Info lists the firmware version currently installed on the module.
XHD6801+ Installation and Operation Manual 19
Chapter 2: Installation
• View the firmware version currently installed on the module by clicking Version Info.
7. Press Browse... to select the firmware upgrade package (ZIP file).
A standard Windows File Selection dialog opens.
8. Choose the upgrade ZIP file on a local or network drive.
The selected file’s path name is displayed in the edit box to the left of the Browse… button.
NoteThe extraction process of the ZIP file is handled as part of the upgrade process. You do not need to extract the files yourself. You can view the contents of the ZIP file by clicking Package Info.
9. Press Submit Transfer...
A dialog box opens, requesting confirmation that you want to proceed with the request. If you have multiple devices selected, multiple transfer tasks are submitted—one per device.
The transfer now progresses. You may minimize the Software Upgrade window, continue with other tasks, or switch to the Progress tab to view the status of the transfers.
NoteClosing the Software Upgrade window does not effect any of the transfer processes that may be running in the background. If you try to log off or exit the CCS software while a transfer is underway, a notification window will alert you that processes are still active and will ask if you want to terminate these processes.
10. To monitor the progress of the firmware upgrade procedure, click the Progress tab. When the firmware upgrade is complete, Completed is displayed in the Transfer Status column.
Figure 2-6. Firmware Upgrade Complete
20 XHD6801+ Installation and Operation Manual
Chapter 2: Installation
Correcting a Failed Upgrading ProcedureFirmware upgrades may fail in the event of network interruptions, power failures, or if the wrong upgrade package was transferred to the module. These problems can be corrected by upgrading the firmware while the module is in Boot Loader mode. The upgrade won't work unless you put the module in Boot Loader mode.
Note
If you have not already downloaded the most recent appropriate upgrade package from our website or from your CD-ROM, do so now.
Putting the Module in Boot Loader Mode
Follow these steps to put your the module in Boot Loader mode:
1. Remove the affected module from the 6800+ frame.
Figure 2-7. Buttons on a Typical Card Edge
2. Set the hex switch to F.
3. While pressing the Navigation toggle switch down, reinsert the module into the frame.
If your device is listed in the Discovery or Network folder, you can continue the firmware upgrade as described in “Upgrading the Firmware” begining with step 3 page 18. If not, you must manually add the device to the Discovery or Network folder. To do this, see the next section.
Hex switch (mode select rotary switch)
Navigation toggle switch
XHD6801+ Installation and Operation Manual 21
Chapter 2: Installation
Manually Adding a Device to the Discovery or Network Folder
If your device is not listed in the Discovery or Network folder, you must manually add it to these folders. After you add the device, you can use the Software Upgrade dialog box to continue with the module firmware upgrade.
To manually add a device to the Discovery or Network folder, follow these steps:
1. Enter Build mode, and then drag or copy and paste the module’s device icon from the Catalog folder into the Network or Discovery folder.
2. Right-click the device icon, and then select Properties.
3. On the Device tab of the Navigation Properties box, enter the IP address of the frame that holds the module. (See Figure 2-8.)
Figure 2-8. Navigation Properties Box
Caution
Do not make changes in the last field (located above and to the right of the Set Default button). If you do, you will need to begin the process of adding devices to the Discovery or Network folder again.
Do not make changes in this field
Enter frame IP address here
Frame number=0 Slot number=17Must be set to 1
22 XHD6801+ Installation and Operation Manual
Chapter 2: Installation
4. In the third field, enter
1.0.[slotnumber]
(where, for example, 1.0.5 would refer to the module in slot 5 of the frame number 0).
5. Close the window.
6. You can now continue your firmware upgrade as described in “Upgrading the Firmware” begining with step 3 on page 18.
XHD6801+ Installation and Operation Manual 23
Chapter 2: Installation
24 XHD6801+ Installation and Operation Manual
Chapter 3
Configuration and Operation
OverviewThis chapter describes how to operate the XHD6801+ using card-edge controls or CCS software and hardware controls.
The following topics are discussed in this chapter:
• “Operating Notes” on page 26
• “Video Processing Modes” on page 27
• “Q-SEE Compliant Thumbnails” on page 30
• “Changing Parameter Settings” on page 32
• “Entering License Keys” on page 36
• “Aspect Ratio Processing” on page 37
• “Active Format Description” on page 40
• “Closed Captioning and DVB Teletext Captioning” on page 52
• “Audio Configuration” on page 53
• “GPI” on page 56
• “Video Keying” on page 56
XHD6801+ Installation and Operation Manual 25
Chapter 3: Configuration and Operation
Operating NotesWhen setting the control parameters on the XHD6801+, observe the following:
• When you change a parameter, the effect is immediate. However, the module requires up to 20 seconds to save the latest change. After 20 seconds, the new settings are saved and will be restored if the module loses power and must be restarted.
• For proper operation, the output HD standard frame rate should match or double the reference standard frame rate.
• The manufacturer recommends that you terminate any unused coaxial output connectors with a 75connector.
26 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Video Processing ModesThe XHD6801+ operates in three fundamental video processing modes. These modes are available in all three XHD6801+ versions (XHD6801+UC, XHD6801+D and XHD6801+UCD).
Note
Some user controls such as input and output video standard, phasing, and LOV may operate differently between the processing modes. Also, there are some requirements on the video format on each of the outputs, and these requirements vary between the processing modes.
Mode 1: Scaled Outputs with Re-clocked Inputs
Figure 3-1. Scaled Outputs with Re-clocked Inputs
This mode is active when you select Reclock in Video > Output > DA Output Select.
Four re-clocked outputs of the input video with four scaled outputs are available in this mode. This makes it possible to configure the XHD6801+ as a combined four-output DA and a four-output up/cross/downconverter. The following special features and limitations apply to this video processing mode:
• The input video standard control (Video > Input > SDI Input Standard Set) applies to the video frame synchronizer only and has no effect on the re-clocked outputs. If the input video format does
Video frame sync
Scalar andaudio /ancillary
processor
Reclocked outputs
Program and monitor
outputs
SDI input
XHD6801+ Installation and Operation Manual 27
Chapter 3: Configuration and Operation
not match the input standard control setting or if the input video is lost, both frame synchronizer and the scalar processor will operate in LOV mode.
• The output video standard of the scalar is selectable through the scalar output video standard control (Video > Output > Output Video Standard Select). However, the video format of the re-clocked outputs is not controllable and is always the same as the input video format.
• The horizontal and vertical phasing controls will apply to both video frame synchronizer and scalar processing as a single block. The phasing controls (Video > Processing > Synchronizer) have no effect on the re-clocked outputs.
• If the input video format does not match the input standard control setting or if the input video is lost, the program and monitor outputs will either be frozen, undetermined (pass mode), or black—according to the LOV mode setting (Video > Output > Primary LOV Mode). However, the LOV mode does not apply to re-clocked outputs. The re-clocked outputs will be undetermined if the input video format is not supported, or if the input video is lost.
Mode 2: Frame Sync and Scalar Outputs
Figure 3-2. Frame Sync and Scalar Outputs
This mode is active when you select FS Mode 1 in Video > Output > DA Output Select.
Video frame sync
Scalar andaudio / ancillary
processor
SDI input
Frame sync
outputs
Program and monitor outputs
28 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
In this mode, there are four frame synchronized outputs of the input video and four scaled outputs available. The scalar processor is located after the video frame synchronizer on the same path. However, putting both the frame synchronizer and the scalar on the same path prevents you from changing the phase relationship between the frame synchronized outputs and the scalar outputs. The following special features and limitations apply to this video processing mode:
• The input video standard control applies to both the video frame synchronizer and the scalar processor (Video > Input > SDI Input Standard Set). If the input video format does not match the input standard control setting, or if the input video is lost, both the frame synchronizer and the scalar processor will operate in the LOV mode.
• The output format of the scalar is selectable through the scalar output video standard control (Video > Output > Output Video Standard Select). However, the output video format of the frame synchronized outputs is controlled by the input video standard control.
• The horizontal and vertical phasing will apply to both video frame synchronizer and scalar processing as a single block (Video > Processing > Synchronizer). In other words, you cannot adjust the phase relationship between the frame synchronizer outputs and the scalar outputs. The scalar outputs will always lag the frame synchronizer outputs by a fixed number of video frames (the amount of propagation delay through the scalar processor).
• If the input video format does not match the input standard control setting or if the input video is lost, the program and monitor outputs will either be frozen, undetermined (pass mode), black, or test pattern—according to the LOV mode setting (Video > Output > Primary LOV Mode). The frame synchronizer outputs will also either be frozen, undetermined (pass mode), or black.
XHD6801+ Installation and Operation Manual 29
Chapter 3: Configuration and Operation
Mode 3: Discrete Frame Sync and Scalar Outputs
Figure 3-3. Discrete Frame Sync and Scalar Outputs
This mode is active when you select FS Mode 2 in Video > Output > DA Output Select.
In this mode, there are four frame synchronized outputs of the input video and four scaled outputs available. The scalar processor is not located after the video frame synchronizer on the same path.
Q-SEE Compliant ThumbnailsThe OP+TDMR+8 and OP+TDMT+8 modules support Q-SEE compliant thumbnails. To use Q-SEE compliant features, you must install the modules in an FR6822+QXFE frame or an FR6802+QXF frame that also contains a 6800+ETH module. When you open a Control window in CCS Pilot or Navigator for the 6800+ETH module, all Q-SEE compliant modules provide thumbnails on a Video Streaming tab. In addition, the OP+TDMR+8 and OP+TDMT+8 module Control windows have a Streaming tab where a thumbnail is displayed and updated at up to three frames per second.
Q-SEE-compliant thumbnails are available for all inputs, but only one can be viewed at a time.
The following standards are supported:
59.94 Hz Operation
• 525• 720p/59• 1080i/59
Scalar andaudio / ancillary
processor
SDI input
Frame sync
outputs
Program and monitor outputs
Video Frame Sync
30 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
• 1080p/29.97• 1080p/23.98
50 Hz Operation
• 625• 1080i/50• 1080p/25• 720p/50
For more information on Q-SEE compliant thumbnails, see your FR6802+QXF or FR6822+QXFE Frames Installation and Operation Manual.
XHD6801+ Installation and Operation Manual 31
Chapter 3: Configuration and Operation
Changing Parameter SettingsThere are two ways to change the parameters that control your module’s operation: CCS software applications and card-edge controls.
Using CCS software applications, such as + Pilot Lite, Pilot, or Navigator, you can view, set, and confirm your module’s parameter settings from your computer’s monitor. Using the card-edge controls, you can set parameters using the module’s rotary hex and navigation switches.
You can use the information in this chapter to configure and operate your XHD6801+ using a CCS software application or the module’s card-edge controls. For more information about setting parameters using CCS software application or by using the module’s card-edge control, see “Changing Parameters Using CCS Software” on page 32 and “Changing Parameter Settings Using Card-Edge Controls” on page 33 respectively.
A complete list of XHD6801+ control parameters can be found in Chapter 4: “Parameters, LEDs, and Alarms” on page 57.
Changing Parameters Using CCS SoftwareBefore using CCS software applications or hardware controls to change your module’s parameter settings, you must refresh (+ Pilot Lite) or discover (Pilot and Navigator) the module. Refresh and Discovery are the processes by which your CCS software finds, and then connects to your module.
Refreshing Your Module Using + Pilot Lite
When using + Pilot Lite to change your XHD6801+ control parameters, you must “refresh” the control connection between your 6800+ frame and PC. To refresh the connection, from the + Pilot Lite menu bar, select File > Refresh. For information about controlling a device using + Pilot Lite, see your + Pilot Lite User Manual.
32 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Discovering an XHD6801+ Module
To discover your module, your Pilot or Navigator software must be in Build mode. Follow these steps:
1. If the Discovery window is not open, click Tools > Discovery in the main menu.
A Discovery window opens, most likely in the bottom left corner of the screen.
2. Click Options, and then click Add.
3. Enter the IP address of the frame that contains your module, the frame that contains your ICE6800+ module, or the frame that contains a 6800+ETH module that provides access to your module.
4. Click OK to close the Add IP address window, and then OK again to close the Discovery Options window.
5. Click Start.
This triggers Pilot or Navigator to run a discovery.
6. When your discovery is complete, Discovery Completed is displayed in the Discovery window.
7. To continue, click Save, to save the contents of your discovery to the Discovery folder of the Navigation pane.
You can now switch to Control mode by selecting Operational Mode > Control. Double-click XHD6801+ in the Navigation pane. The Control window opens and displays the module’s controls.
Changing Parameter Settings Using Card-Edge ControlsUsing the module’s rotary and navigation switches, you can change XHD6801+ parameter settings at the card-edge. You can view and confirm your changes using the On-screen display feature (see “Enabling On-Screen Display” on page 35).
Follow these steps to change the parameter settings at the card edge:
1. Rotate the mode select rotary switch (hex switch) to 0.
XHD6801+ Installation and Operation Manual 33
Chapter 3: Configuration and Operation
2. Once the hex switch is set to 0, toggle the navigation switch up or down to select a bank.
View the control LEDs next to the navigation toggle switch. A lit LED indicates which bank is currently selected.
3. Rotate the hex switch to the parameter number (1 to 9) or letter (A to F) of the option you want to set.
4. Toggle the navigation switch to select and set the value of the chosen parameter.
Table 3-1. Bank Select LEDs
Bank Number
Bank 0 LED(first top LED)
Bank 1 LED(second top LED)
Bank 2 LED(third top LED)
Bank 3 LED (fourth top LED)
0 Off Off Off Off
1 On Off Off Off
2 Off On Off Off
3 On On Off Off
4 Off Off On Off
5 On Off On Off
6 Off On On Off
7 On On On Off
8 Off Off Off On
9 On Off Off On
10 Off On Off On
11 On On Off On
12 Off Off On On
13 On Off On On
14 Off On On On
15 On On On On
34 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
5. Rotate the hex switch to another parameter number/letter in the current bank, and then repeat step 4.
or
Rotate the hex switch to 0 again to select a different bank, and then repeat steps 3 and 4.
Note
Harris recommends that you use the software controls to aid in viewing, setting, and confirming parameter values.
Enabling On-Screen DisplayYou can use the On-screen Display (OSD) monitoring feature to view the current parameter selections on your output display. When the On-Screen Display parameter is turned on, the current parameter selections are displayed on the module’s SDI Program/Monitor Out 1 and SDI Program/Monitor Out 2 outputs. This features makes configuring the XHD6801+ using the card-edge controls much easier.
To enable OSD monitoring, select Video > Output > Config > On-Screen Display. To change the transparency of the OSD, select Video > Output > Config > OSD Transparency.
OSD can be turned On/Off at the card edge, using Bank 0, Switch 2 (0,2).
Recalling Default Parameter SettingsYou can use the module’s Factory Recall parameter to return all of the module’s parameters to factory default settings. To return this module to its default settings, select Other > Factory Default > Yes.
Reading Software and Hardware VersionsYou can see the current software and hardware versions of the XHD6801+ by checking the Hardware Version and Firmware Version read-only parameters near the end of the parameter list (see “Control Parameters” on page 58). These parameters appear in the on-screen display and in CCS software applications.
XHD6801+ Installation and Operation Manual 35
Chapter 3: Configuration and Operation
Entering License KeysOptional license keys are available to add new capabilities to your existing module. (Contact your product sales representative for details.)
Before you purchase a license key, you must obtain your module’s serial number. Select Other > Serial Number. The module’s current capabilities are shown when you select Other > Options.
Table 3-2 lists the available XHD6801+ upgrade licence keys.
You can use a CCS software application, such as CCS +Pilot Lite, Pilot, and Navigator, as well as NUCLEUS control panels to enter license keys. Additionally, you can enter the license keys with a web browser if your module is in a frame with (or connected to a frame with) a 6800+ETH+HTTP module. License keys cannot be entered at the module’s card edge, but you can view the License Key parameter if the On Screen Display parameter is enabled.
Using CCS, you can enter your license key by selecting Other > License Key.
To confirm that your license key has been accepted and activated, select Other > Options.
Note
Before you can enter and activate your upgrade license key, you must either Refresh or Discover your XHD6801+ module as described in “Refreshing Your Module Using + Pilot Lite” on page 32 and “Discovering an XHD6801+ Module” on page 33.
Table 3-2. Available Upgrade License Keys
Module Type Before Upgrade License Key Upgrade Module Type
After Upgrade
XHD6801+UCT Up/cross/downconversion(XHD68+-UC-UG-UCD)
XHD6801+UCDT
XHD6801+DT Up/cross/downconversion(XHD68+-D-UG-UCD)
XHD6801+UCDT
36 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Aspect Ratio Processing The XHD6801+ offers a highly configurable and comprehensive feature set for processing aspect ratio codes and determining ARC settings. ARC control and AFD/WSS/VI code insertion control can track, but can also operate independently from each other. In addition, user-defined mapping makes it possible to have complete control over what ARC and code is inserted for any given input of AFD, WSS, or VI code. The aspect ratio features described here require a 6800+ETH resource module firmware of at least version 4.2.
Enhanced Aspect Ratio Conversion ControlGPI triggers can modify the aspect ratio conversion control for each mode of operation separately. In other words, you can change the ARC for upconversion without affecting the ARC for down- or crossconversion. For example, if the XHD6801+ is in upconversion mode, the GPI can only change the upconversion ARC setting. This capability makes it possible to control the ARC control for any mode, regardless of which mode is currently active.
A user-selectable ARC setting is provided in the event that AFD, WSS, or VI code disappears. For example, if upconversion is set to follow AFD, but the AFD data isn't available, the user can choose which ARC to implement in its place.
Enhanced AFD/WSS/VI InsertionGPI triggers can affect the insertion mode and insert specific codes for AFD, WSS, and VI. Each control is separate and independent from the other.
Enhanced Monitoring
GPI outputs on the XHD6801+ can perform the following:
• Monitor for specific input AFD, WSS, and VI codes
• Separately monitor the ARC setting for each conversion mode
• Report the current AFD, WSS, or VI insertion mode in use for a particular type of conversion
XHD6801+ Installation and Operation Manual 37
Chapter 3: Configuration and Operation
Enhanced User ARC Settings
Each user setting includes default AFD, WSS and VI code associated with it. A Live View mode makes it possible to see custom ARC adjustments in real time.
Custom Code Map
With the custom code map, you have the ability to precisely specify the ARC setting and code insertion for each input AFD, WSS, and VI code, including reserved codes. You can override only the code insertion, the ARC setting, or both. In addition, you can override specific AFD, WSS, or VI codes and leave the remainder as default.
The map can be used to create custom AFD In to AFD Out mappings, as well as custom translation from any incoming AFD, WSS, and VI to insert any AFD, WSS, and VI code.
GPI triggers make it possible to switch between standard mapping and custom mapping for each conversion mode separately.
Selecting a Standard Aspect RatioTo select a standard aspect ratio for the output image, set ARC Control (found at Video > Processing > ARC > ARC Control) to one of the following selections:
• Anamorphic
• 4:3 Pillar Box
• 14:9 Pillar Box
• 16:9 Cut
• 4:3->21:9 Ltr
• 16:9 Letter Box
• 14:9 Letter Box
• 4:3 Cut
• 16:9->21:9 Ltr
• PixelTrue
Pixel True performs no scaling to the input video. Instead, each input pixel is mapped directly to one output pixel. You can use this preset to transport an SD picture embedded inside an HD stream.
38 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Selecting a Custom Aspect RatioTo select a pre-defined custom aspect ratio for the output image, use one of the options found at Other > GPI Input > ARC Control:
• Custom Up ARC1 to Custom Up ARC5
• Custom Down ARC1 to Custom Down ARC5
• Custom Cross ARC1 to Custom Cross ARC5
• Custom SD ARC1 to Custom SD ARC5
Only five options are exposed at one time, based on the mode selected.
Selecting Aspect Ratio Control Following AFD, VI, WSSAn XHD6801+ module can automatically change the aspect ratio, based on the incoming AFD, WSS, or VI control codes. Set the ARC Control parameter to one of the following selections (some options are not available, depending upon the selected conversion mode):
• AFD
• AFD - ALTR
• AFD - Custom Map
• VI
• VI - ALTR
• VI - Custom Map
• WSS
• WSS - ALTR
• WSS - Custom Map
The AFD, WSS, and VI selections follow standard ARC recommendations. For instance, selecting AFD causes the module to set the ARC setting according to the incoming AFD code, -ALTR selections use the alternate ARC method, and Custom Map follows the user defined ARC settings for each individual code. See “Active Format Description” on page 40 for more details about custom mapping.
XHD6801+ Installation and Operation Manual 39
Chapter 3: Configuration and Operation
Setting a Custom Aspect RatioYou can scale and pan the output image to any size and location by using the various parameters of the custom aspect ratio settings. These parameters include: Horizontal Offset, Vertical Offset, Horizontal Scale, Vertical Scale, Crop Left, Crop Right, Crop Top, and Crop Bottom. These parameters can be individually modified, or batch-modified by recalling a standard aspect ratio or a pre-defined custom aspect ratio.
Setting Live Edit View to On will actually make the custom aspect ratio settings take effect immediately on the output. This is useful when trying to visually align the various parameters.
Custom aspect ratios are configured by choosing a custom aspect ratio name from Save ARCs selections.
All of the related controls can be found at Video > Processing > ARC > Custom ARC.
Active Format DescriptionActive Format Description (AFD) transmits data in the VANC portion of the SDI signal, enabling both 4:3 and 16:9 television monitors to optimally present video with preset ARC and safe area information. Without AFD, converted video may appear distorted or “cut off” when it appears on different monitors. The XHD6801+ can encode or decode AFD; it can also encode or decode earlier Video Index (VI) and Wide Screen Signalling (WSS) formats.
The AFD feature of the XHD6801+ complies with SMPTE 2016 and includes nine possible 4:3 configurations and eight possible configurations in 16:9. Figure 3-7 on page 46 describes the 4:3 AFD configurations; Figure 3-8 on page 47 describes the 16:9 AFD configurations.Figure 3-4 shows two comparisons of a signal that is encoded with AFD and without AFD.
AFD/ARC AlignmentWhen you use AFD to select which aspect ratio to apply, the XHD6801+ensures that the AFD codes and associated image will remain in sync. For example, during a hotswitch, the new ARC will only be applied to the new image. There are a few cases which could cause AFD/ARC misalignment:
40 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
• The ARC applied is reducing the image vertically such that the new image is less than 60% of the original image.
• The output standard is set to either 1080p/23.98 or 1080p/29.97.
Figure 3-4. AFD/Non-AFD Comparisons
SD-SDI 4:3 HD-SDI 16:9
Full frame Pillarbox
DownUp
Postage stamp
Full frame
SD-SDI 4:3
16:9 Letterbox
SD-SDI 4:3
Up
Postage stamp
Full frame
HD 16:9
Using active format description (best result)
Without active format description (undesirable result)
Using active format description, the original image
information is maintained throughout the entire
conversion, creating the best possible viewing area .
XHD6801+ Installation and Operation Manual 41
Chapter 3: Configuration and Operation
Figure 3-5 shows different applications of AFD insertion and decoding.
Figure 3-5. AFD Block Diagram
The AFD feature of the XHD6801+ includes nine possible SD-SDI configurations and eight possible configurations in HD-SDI. Figure 3-9 on page 48 describes the SD-SDI AFD configurations; Figure 3-10 on page 49 describes the HD-SDI AFD configurations.
AFD, VI, and WSS DetectionAFD, VI, and WSS data that is embedded in the incoming video can be detected by the XHD6801+, and read from the following input parameters that are found in the Processing > ARC > Status path:
• AFD Present
• VI Scan Present (Use the VI Detect Line Field 1 and VI Detect Line Field 2 parameters to determine where in the video signal to look for VI information)
• VI AFD Present
• WSS Present (Use the WSS Detect Line parameter to determine where in the video signal to look for WSS information)
XHD6801+
Insertion of AFD
Detection and signaling of ARC
-SDI /SD HD (AFD in VANC)
HD-SDI (AFD in VANC)
SD-SDI (WSS/VI)
SD/HD-SDI (AFD in VANC)
HD-SDI (AFD in VANC)
SD-SDI (WSS/VI)
SD/HD-SDI (AFD in VANC)- SDI /SD HD (No AFD)
XHD6801+
XHD6801+
XHD6801+
42 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
AFD, VI and WSS Code InsertionAFD, VI and WSS data can be passed from input to output, or it can be generated manually or automatically by the XHD6801+ module. This function is controlled by the AFD Insert, VI Insert, and WSS Insert parameters located in the Video > Processing > ARC > AFD-VI-WSS Insertion path. Table 3-3 lists the function of each of the available options (some options are not available in all conversion modes).
You can also remove WSS from the input video stream. To do this, follow: Video > Input > De-embedder > Input WSS Remove
Table 3-3. AFD, VI and WSS Code Insertion
Option Details
Pass The incoming AFD, VI or WSS code is inserted unmodified. (This option is only supported in SD-ARC and crossconversion modes. In up- or downconversion modes, the Pass option is equivalent to a loss of code, even when an input code is present. When a loss of code occurs, the module will insert your selection from the AFD Pass on Loss, VI Pass on Loss, or WSS Pass on Loss parameters.)
Remove No code is generated by the module. The original input code is removed, except for the following:
• WSS in line 23
• All codes in proc bypass mode.
Auto The module generates code automatically and inserts it. The code can be generated in one of the following scenarios:
• A standard or custom aspect ratio is selected, and the corresponding AFD, VI, or WSS code is inserted.
• The ARC Control parameter is set to AFD, AFD-ALTR, VI, VI-ALTR, WSS, or WSS-ALTR, and the generated output code is based on input code according to the alternate implementations of the standard.
• The ARC Control parameter is set to AFD-Custom Map, VI-Custom Map or WSS - Custom Map, and the output code is generated from the custom map settings.
• Custom AFD Map
• Custom VI Map
• Custom WSS Map
The output code is generated according to the custom map table.
(code list) The actual code selected is inserted
XHD6801+ Installation and Operation Manual 43
Chapter 3: Configuration and Operation
AFD, VI, WSS Based Aspect Ratio ControlWhen you set the ARC Control parameter to follow the aspect ratio codes (AFD, AFD-ALTR, AFD-Custom Map, VI, VI-ALTR, VI-Custom Map, WSS, WSS-ALTR, and WSS-Custom Map), the aspect ratio control is based on input AFD, VI, or WSS code. AFD-Custom Map, VI-Custom Map, and WSS-Custom Map make it possible for you to perform automatic aspect ratio conversions based on the custom defined mapping table. The other options set the ARC to an existing standard. When the input code is missing, the ARC behavior is defined by Loss of AFD ARC, Loss of VI ARC or Loss of WSS ARC. Only one of these options can be enabled at any one time.
Though they are not widely used, some AFD, VI or WSS codes recommend cropping part of the image. When this type of cropping is enabled, the module will take longer to change ARC modes. To create faster ARC transitions, you can disable the cropping using the AFD Crop Enable parameter (Video > Processing > ARC > ARC Control).
When the ARC is based on AFD, VI, or WSS, and the output standard is SD-SDI, you must set the output aspect ratio (either 4:3 or 16:9) to ensure that the correct mapping table is used. (Follow Video > Processing > ARC > ARC Control > SD Out Aspect Ratio.)
AFD, VI, WSS Custom Mapping ConfigurationUsing the controls in Video > Processing > ARC > AFD-VI-WSS Custom Map, you can define a special mapping table other than the one specified by a standard. Given any input AFD, VI or WSS code, you can define the aspect ratio behavior and output AFD, VI and WSS code independently.
Advanced ControlsThe de-embedding line controls for VI and WSS are at Video > Input > De-embedder. The embedding line number controls for AFD, VI, and WSS are at Video > Output > Embedder.
If you are using VI according to the SMPTE Proposed RP-186+ standard as of January 11, 2007, you must ensure you have enabled the standard by following this path: Video > Output > Embedder > SD Out VI with AFD (default setting is Yes).
At this time, Bar Data and Pan-Scan for VI and AFD are not supported.
44 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
AFD DescriptionsIn the following pages, Figures 3-7 to 3-12 show the different AFD code descriptions. Comparable WSS and VI templates are included in the SD-SDI descriptions.
Figure 3-6. Explanation of AFD Diagrams
Bounding box representsthe coded frame.
The smallest rectangle enclosingthe white regions indicates the areaof essential picture information.
Black regions indicate areasof the picture that do notcontain useful information andshould be cropped by thereceiver where appropriate.
Gray regions indicate areas of the picturethat may be cropped by the receiverwithout significant loss to the viewer.
XHD6801+ Installation and Operation Manual 45
Chapter 3: Configuration and Operation
Figure 3-7. Available AFD Select Options when OutAspectRatio is Set to 4:3
AFD 4:3 code and description
Illustration in a4:3 coded frame Description
Image with a 16:9 aspect ratio and with analternative 4:3 center as a vertically centered
letterbox in a 4:3 coded frame
alternative 14:9 center as a vertically centeredImage with a 16:9 aspect ratio and with an
letterbox in a 4:3 coded frame
Image with a 4:3 aspect ratio and with analternative 14:9 center in a 4:3 coded frame
Image with 14:9 aspect ratio as a verticallycentered letterbox in a 4:3 coded frame
Image with a 16:9 aspect ratio as a verticallycentered letterbox in a 4:3 coded frame
Image is full frame, with an aspect ratio that isthe same as the 4:3 coded frame
Image with aspect ratio greater than 16:9 asa vertically centered letterbox in a 4:3 coded
frame
Image with a 14:9 aspect ratio as letterbox atthe top of a 4:3 coded frame
Image with a 16:9 aspect ratio as letterbox atthe top of a 4:3 coded frame
WSS name
100 16:9 Top
010 14:9 Top
101GT 16:9
0004:3 Full
01116:9 CNTR
00114:9 CNTR
1104:3 A 14:9
Not applicable
Not applicable
AFD and VI Select parameter options
(4:3) 001016:9 Top
(4:3) 001114:9 Top
(4:3) 0100GT 16:9
(4:3) 101016:9 L
(4:3) 101114:9 L
(4:3) 10004:3 Full
(4:3) 11014:3 A 14:9
(4:3) 111116:9 LA 4:3
(4:3) 111016:9 LA 14:9
46 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Figure 3-8. Available AFD Select Options when OutAspectRatio is Set to 16:9
AFD 16:9 code and description
Illustration in a16:9 coded frame
(16:9) 0100 GT 16:9
AFD and VI Select parameter options
(16:9) 111116:9 A 4:3
(16:9) 101114:9 P
(16:9) 11014:3 P A 14:9
(16:9) 1110 16:9 A 14:9
(16:9) 100016:9 Full
(16:9) 101016:9 Prtctd
(16:9) 1001 4:3 P
Description
Image with a 16:9 aspect ratio and withan alternative 4:3 center in a 16:9 coded
frame
Image with a 16:9 aspect ratio and withan alternative 14:9 center in a 16:9
coded frame
Image with a 4:3 aspect ratio and with analternative 14:9 center as a horizontallycentered pillarbox image in a 16:9 coded
frame
Image with a 14:9 aspect ratio as ahorizontally centered pillarbox image
in a 16:9 coded frame
Image is full frame, with a 16:9 aspectratio and with all image areas protected
Image with a 4:3 aspect ratio as ahorizontally centered pillarbox image
in a 16:9 coded frame
Image is full frame, with an aspect ratiothat is the same as the 16:9 coded
frame
Image with aspect ratio greater than 16:9as a vertically centered letterbox in a
16:9 coded frame
Not applicable
WSS name
111Anamorphic
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
XHD6801+ Installation and Operation Manual 47
Chapter 3: Configuration and Operation
Figure 3-9. Available AFD Select, VI Select, and WSS Select Options When Converting from 4:3 to 16:9
4:3 to 16:9 conversion
Illustration in a4:3 coded frame Conversion Conversion (Alternative)WSS name AFD and VI Select
parameter options
(4:3) 001016:9 Top
(4:3) 001114:9 Top
(4:3) 0100GT 16:9
(4:3) 101016:9 L
(4:3) 101114:9 L
(4:3) 10004:3 Full
(4:3) 11014:3 A 14:9
(4:3) 111116:9 LA 4:3
(4:3) 111016:9 LA 14:9
100 16:9 Top
010 14:9 Top
101GT 16:9
0004:3 Full
01116:9 CNTR
00114:9 CNTR
1104:3 A 14:9
Not applicable
Not applicable
48 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Figure 3-10. Available AFD Select, VI Select, and WSS Select Options When Converting from 4:3 to 4:3
4:3 to 4:3 conversion
Conversion(Alternative)
ConversionIllustration in a4:3 coded frameWSS name AFD and VI Select
parameter options
(4:3) 001016:9 Top
(4:3) 001114:9 Top
(4:3) 0100GT 16:9
(4:3) 101016:9 L
(4:3) 101114:9 L
(4:3) 10004:3 Full
(4:3) 11014:3 A 14:9
(4:3) 111116:9 LA 4:3
(4:3) 111016:9 LA 14:9
100 16:9 Top
010 14:9 Top
101GT 16:9
0004:3 Full
01116:9 CNTR
00114:9 CNTR
1104:3 A 14:9
Not applicable
Not applicable
XHD6801+ Installation and Operation Manual 49
Chapter 3: Configuration and Operation
Figure 3-11. Available AFD Select, VI Select, and WSS Select Options When Converting from 16:9 to 4:3
16:9 to 4:3 conversion
Illustration in a16:9 coded frame
Conversion (Alternative)Conversion
(16:9) 0100 GT 16:9
AFD and VI Select parameter options
(16:9) 111116:9 A 4:3
(16:9) 101114:9 P
(16:9) 11014:3 P A 14:9
(16:9) 1110 16:9 A 14:9
(16:9) 100016:9 Full
(16:9) 101016:9 Prtctd
(16:9) 1001 4:3 P
Not applicable
WSS name
111Anamorphic
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
50 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Figure 3-12. Available AFD Select, VI Select, and WSS Select Options from 16:9 to 16:9
16:9 to 16:9 conversionConversion (Alternative)Conversion
Illustration in a16:9 coded frame
(16:9) 0100 GT 16:9
AFD and VI Select parameter options
(16:9) 111116:9 A 4:3
(16:9) 101114:9 P
(16:9) 11014:3 P A 14:9
(16:9) 1110 16:9 A 14:9
(16:9) 100016:9 Full
(16:9) 101016:9 Prtctd
(16:9) 1001 4:3 P
Not applicable
WSS name
111Anamorphic
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
XHD6801+ Installation and Operation Manual 51
Chapter 3: Configuration and Operation
Closed Captioning and DVB Teletext CaptioningAlthough North America has dedicated standards for closed captioning of video (EIA-608 and 708), many countries in Europe and elsewhere have not yet adopted formal standards. For these countries, closed captioning is part of the DVB Teletext System as described in ITU-R BT-653-3. These specifications define all Teletext Systems (Systems A, B, C, D) used in the world and are also known as the World System Teletext (WST). A Teletext system is made of several pages of various data information and CC data is described in one these pages. System B is used in Australia, the UK, and Germany, among other countries.
Australian closed captions are inserted on line 21/334 in analog PAL broadcast signals, as per the ITU-R BT-653-3. When analog PAL is produced or converted to SDTV (625 digital), a digitized version of the closed captioning appears on line 21/334 (in the same way line 21 on NTSC signals is digitized and appears on the line 21 of SD-SDI signals). The ITU-R BT-653-3 document proposed by Free TV Australia indicates how to carry this CC data into the VANC area of SD-and HD-SDI signals by use of the SMPTE 334M VANC embedding protocol. For digital broadcasting, Australia intends to use the ETSI EN 300 472 standard that specifies the conveyance of ITU-R System B Teletext in DVB bit streams.
Setting Closed Captioning and TeletextTo make changes to the default CC and Teletext settings, use the Closed Captioning/Teletext Embed and Closed Captioning/Teletext Embed Line parameters from the path Video > Output > Embedder path.
To verify the presence of the embedded CC, use the Input Closed Captioning/Teletext Present parameter (Video > Input > De-embedder path).
If you have purchased and enabled the XHD6801+ closed captioning feature, you can use the closed captioning parameters to enable and select the video line in which you want to embed closed captioning data. Contact your product sales representative for information about obtaining a closed captioning license key. If you have already purchased a license key, but have not yet enabled the feature, see “Entering License Keys” on page 36.
52 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Audio ConfigurationXHD6801+ modules process embedded audio. The input embedded audio from SDI 1 is demultiplexed (de-embedded) and synchronized to the video, delayed to match the video processing delay, processed, and then remultiplexed (re-embedded) into HD- and SD-SDI video output. Up to four groups of audio can be embedded into the video stream.
Audio ControlsXHD6801+ modules can route audio from one of several sources to the outgoing SDI signal (up to 8 channel pairs can be embedded).
The modules are capable of demultiplexing up to four groups of embedded audio from the primary video SDI stream, and embedding up to four groups into the output SDI stream. XHD6801+ modules can select up to eight channel pairs of embedded audio.
The Demux Group Present and Demux Channel Pairs Present parameters (Audio > Input > Status > Demux Group Present and Demux Channel Pairs Present) indicate which groups and channel pairs have audio present in the video inputs.
See page 55 for more information about audio status parameters.
Audio Routing
Input
To manually configure the audio inputs, you will need to select options in the Audio > Input > Routing section. Set your options in the SRC1 to SRC8 Input Select parameters.
The default settings for the inputs follow this pattern:
• SRC1 Input Select = SDI 1 Group 1 Channel 1/2
• SRC2 Input Select = SDI 1 Group 1 Channel 3/4
• SRC3 Input Select = SDI 1 Group 2 Channel 1/2
• SRC4 Input Select = SDI 1 Group 2 Channel 3/4, etc.
XHD6801+ Installation and Operation Manual 53
Chapter 3: Configuration and Operation
Output
To manually configure the output of the audio, select Enable in Mux Group 1 Enable to Mux Group 4 Enable. (This is found at Audio > Output > Embedder > Mux Group 1 Enable to Mux Group 4 Enable.)
Then set your options in the Routing section (Audio > Output > Routing > Mux Group x Channel x).
The default audio routing settings follow this pattern:
• Mux Group 1 Channel 1 = SRC 1A• Mux Group 1 Channel 2 = SRC 1B• Mux Group 2 Channel 1 = SRC 2A• Mux Group 2 Channel 2 = SRC 2B, etc.
In addition to selecting audio sources from the video groups, four custom tone generators are available, as well as Mute and SMPTE RP155 and EBU R68 tones. To set the four custom tones, follow the path to Audio > Other > Tones > Tone Generators 1 to 4 Level.
Audio Proc AmpGain, bypass, and delay controls are available for the left and right side of each of the processed audio channels. You can individually adjust the gain and delay of the left and right sides of each channel using the control parameters in the Gain and Delay sections (Audio > Processing > Gain or Delay).
The audio can contain non-PCM audio data. In this case, the sample rate converter must be bypassed to ensure audio integrity. You must individually indicate which sample rate converter or gain to bypass using the SRCx Gain/Bypass parameters (Audio > Input > Bypass > SRCx Gain/Bypass). Select Manual in the SRC/Gain Bypass Mode to enable these individual controls.
If you set SRC/Gain Bypass Mode to Auto, the audio will be monitored, and if non-PCM audio data is detected, the sample rate converter for that side of the channel will be bypassed.
In addition to the mute controls that control audio pairs individually, a Master Mute control mutes all of the audio channel pairs (Audio > Processing > Gain > Master Mute). Also, if the audio source for either side of a given audio channel does not have any incoming audio, the signal will be automatically muted.
54 XHD6801+ Installation and Operation Manual
Chapter 3: Configuration and Operation
Audio Status ParametersThe read-only Demux Group Present parameter (in the Audio > Input > Status path) indicates which groups are present in the video input (see Figure 3-13). The “=” indicates no audio is detected for a particular group, while the letter P indicates the presence of audio. For example, “= P= =” means the XHD6801+ detects audio in Group 2, but no audio is detected in the other three groups.
Figure 3-13. Demux Group Present and Demux Group Error
The Demux Group Error parameter (also in the Audio > Input > Status path) displays errors in the same way. In a string of “=” signs, the letter E indicates an error for that audio group.
Demux Channel Pair Present displays the eight channel pairs, with the letter P indicating audio presence (see Figure 3-14).
Figure 3-14. Demux Channel Pair Present/Type
Demux Channel Pair Type displays the eight channel pairs, with the letter A indicating PCM audio, and the letter D indicating non-PCM (data).
= = = =
G ro u p 1 G ro u p 2 G ro u p 3 G ro u p 4
========
Channel Pair 1, Group 1 Channel Pair 2, Group 1 Channel Pair 1, Group 2 Channel Pair 2, Group 2
Channel Pair 2, Group 4Channel Pair 1, Group 4Channel Pair 2, Group 3Channel Pair 1, Group 3
XHD6801+ Installation and Operation Manual 55
Chapter 3: Configuration and Operation
GPI
The XHD6801+ module provides four GPI inputs and two GPI outputs for automation. These are open collector style inputs with approximately 10 K pull-ups to +5V. This means that you can use contact closure-to-ground switches to control these GPI inputs.
GPI InputThe GPI input actions are controlled by parameters in Video > Other > GPI Input.
GPI inputs make it possible to control the ARC being used for a particular conversion mode, as well as the AFD, WSS or VI code to be inserted. The read-only GPI Input Status parameter provides current information. All GPI events occur in the order they are triggered and will override older events.
GPI OutputThe GPI output actions are controlled in the Video > Other > GPI Output path.
GPI outputs can reflect the state of the current ARC being used, or can be triggered on a specific input AFD, WSS or VI code.
The current GPI output active status can be read from the GPO Output Status parameter.
Video KeyingThe video keying feature is activated by following the Video > Output > Config > Video Keying path. When enabled, the key image appears on the SDI Program/Monitor Out feed. The On Screen Display feature (Video > Output > Config > On Screen Display) also appears on the SDI Program/Monitor Out feed when it is enabled.
56 XHD6801+ Installation and Operation Manual
Chapter 4
Parameters, LEDs, and Alarms
OverviewThis chapter describes the parameters, LEDs and alarms used on the XHD6801+.
The following topics are covered:
• “Control Parameters” on page 58
• “LEDs and Alarms” on page 59
XHD6801+ Installation and Operation Manual 57
Chapter 4: Parameters, LEDs, and Alarms
Control ParametersFor a complete list of the XHD6801+ parameters, see the separate XHD6801+ Parameter List and the XHD6801+ On Screen parameter List that accompany this manual.
The parameters are listed in the order that they appear in CCS Pilot and Navigator. If you are using + Pilot Lite, some parameters in the list may not appear in the order as they appear in the software. Also, because of space limitations, some rarely-used parameters will not appear in the OSD list.
On Screen Display MonitoringIf you are using card-edge controls to configure your XHD6801+ module, you can use the OSD Monitoring feature to view the current parameter selections. When the On-Screen Display parameter is turned on, the current parameter selections are displayed on module’s monitoring outputs. For information on enabling OSD Monitoring, see “Enabling On-Screen Display” on page 35.
To view the list of card-edge parameters, see the XHD6801+ On-Screen Display Parameters document, available on the 6800+ CD-ROM.
.
58 XHD6801+ Installation and Operation Manual
Chapter 4: Parameters, LEDs, and Alarms
LEDs and Alarms
LEDsThe module LEDs are located on the card edge of the front module (see Figure 4-1). Table 4-1 on page 60 describes the meanings of the LEDs and their colors.
Figure 4-1. Location of XHD6801+ LEDs
Monitoring LEDs
XHD6801+ Installation and Operation Manual 59
Chapter 4: Parameters, LEDs, and Alarms
Table 4-1. Status and Monitoring LEDs
LED Description Color Indication
Status There is no power to the module; the module is not operational.
None (off)
The module is receiving power and is operating properly.
Green
The module detects an alarm condition or the module’s initialization has failed.
Solid Red
The module has detected a significant hardware/firmware fault; contact your Customer Service representative.
Flashing Red
The module is undergoing configuration. Amber
50-59 Indicates the frame rate for the input video standard
• Green: 59
• Off: 50
525 Indicates the input standard is 525 Green: 525 input standard is detected
625 Indicates the input standard is 625 Green: 625 input standard is detected
720p Indicates the input standard is 720p Green: 720p input standard is detected
1080i Indicates the input standard is 1080i Green: 1080i input standard is detected
1080p Indicates the input standard is 1080p Green: 1080p input standard is detected
Audio1 Reports the presence of audio group 1 in the input video stream
Green: Group 1 audio is present
Audio2 Reports the presence of audio group 2 in the input video stream
Green: Group 2 audio is present
Audio3 Reports the presence of audio group 3 in the input video stream
Green: Group 3 audio is present
Audio4 Reports the presence of audio group 4 in the input video stream
Green: Group 4 audio is present
CC Indicates the presence of closed captioning Green: Closed captioning data is present
Reference Indicates the presence of a valid reference signal Green: Valid signal is present
60 XHD6801+ Installation and Operation Manual
Chapter 4: Parameters, LEDs, and Alarms
AlarmsThe XHD6801+ modules do not have any card-edge alarms. Instead, the module Status LED on the corner of the module lights up red if an error is detected. See Figure 1-1 on page 6 for the location of this LED.
Table 4-2 describes the specific alarms for XHD6801+ modules. You can only identify specific alarms using a software control application.
Table 4-2. XHD6801+ Alarms
Alarm Name Alarm Meaning Alarm Level
SDI 1 Std Mismatch There is a mismatch between reference video and video standard Major
SDI 1 Loss of Video The module detects a loss of video at the SDI 1 input Major
Processing Bypass Active The Scalar Bypass switch (Video > Output > Scalar Bypass) is turned on.
Minor
Reference Not Locked Loss of locked reference Major
Teletext Parity Error The teletext input has a parity error Minor
Teletext Frame Error The teletext input has a frame error. Minor
Master Mute On The master audio mute is enabled. Minor
PCM Vbit Mute On The PCM outputs are automatically muted when the V-bit is set. Minor
Loss of AFD The incoming AFD signal is disrupted. Major
XHD6801+ Installation and Operation Manual 61
Chapter 4: Parameters, LEDs, and Alarms
62 XHD6801+ Installation and Operation Manual
Chapter 5
Specifications
OverviewThe following specification tables appear in this chapter:
• “SD/HD-SDI Video” on page 64
• “Genlock” on page 65
• “SDI Video Outputs” on page 66
• “Audio Delay (Data Out)” on page 67
• “Performance” on page 67
Specifications and designs are subject to change without notice.
XHD6801+ Installation and Operation Manual 63
Chapter 5: Specifications
Inputs
SD/HD-SDI Video
Table 5-1. SD/HD-SDI Video Input Specifications
Item HD-SDI Specification SD-SDI Specification
Number of inputs 1
Standards SMPTE 292M (1.485, 1,485/1.001 Gbps)
SMPTE 259M-C 270 Mbps, 525/625 component video
Frame rate • 1080i: 50, 59.94 Hz
• 720p: 50, 59.94 Hz
• 1080p: 23.98, 29.97, 25 Hz
• 486i: 59.94 Hz
• 576i: 50 Hz
Connector BNC per IEC 169-8 BNC per IEC 169-8
Impedance 75 75
Return loss >15 dB (typical) from 5 MHz to 1485 MHz
>15 dB (typical) from 5 MHz to 270 MHz
Equalization Adaptive cable equalization for up to 328 ft (100 m) (typical) of Belden 1694A coaxial cable at 1.485 Gbps
Adaptive cable equalization for up to 700 ft (230 m) (typical) of Belden 8281 co-axial cable
64 XHD6801+ Installation and Operation Manual
Chapter 5: Specifications
GenlockTable 5-2. Genlock Input Specifications
Item Specification
Connector BNC per IEC 169-8
Impedance 75
Return loss > 40 dB 25 Hz to 30 MHz (SMPTE 318M-1999)
Common mode range • 5.5 V pk-to-pk
Input level • NTSC/PAL-B (1 V pk-to-pk, -4.5 dB to 6.0 dB)• ± 300 mV, -4.5 dB to 6.0 dB for Tri-Level Sync
•1080i: 59.94/50•1080p: 29.97/25
Locking range ± 6 ppm (sync lock only, no burst lock)
Signal type • NTSC/PAL-B analog composite• ± 300 mV Tri-Level Sync
Standard SMPTE 170M (NTSC), ITU-R BT.470-6 (PAL-B), SMPTE 274M (1080i, 1080p)
XHD6801+ Installation and Operation Manual 65
Chapter 5: Specifications
Outputs
SDI Video Outputs
Table 5-3. SD/HD-SDI Reclocked Output Specifications
Item HD-SDI Specification SD-SDI Specification
Number of outputs 8
Standards SMPTE 292M (1.485, 1.485/1.001 Gbps)
SMPTE 259M-C (270 Mbps, 525/625 component video)
Connector BNC per IEC 169-8 BNC per IEC 169-8
Impedance 75 75
Return loss >15 dB (typical) from 5 MHz to 1485 MHz
>15 dB (typical) from 5 MHz to 270 MHz
DC offset 0.0 V ± 0.5 V 0.0 V ± 0.5 V
Signal level 800 mV ± 10% 800 mV ± 10%
Rise and fall time <270 ps (20% to 80%) 400 to 1500 ps (20% to 80%)
Overshoot <10% of amplitude (all outputs terminated)
<10% of amplitude (all outputs terminated)
Jitter • Timing <1 UI pk-to-pk
• Alignment <0.2 UI pk-to-pk
<0.2 UI pk-to-pk
66 XHD6801+ Installation and Operation Manual
Chapter 5: Specifications
Miscellaneous
Audio Delay (Data Out)
Performance
Propagation Delays
Table 5-4. Audio Delay Specifications
Item Specification
Number of outputs 1
Connector BNC per IEC 169-8
Impedance 75
Return loss >20 dB (typical) to 6 MHz
Table 5-5. Performance Specifications
Item Specification
Power consumption 17.5 W
Operating temperature 41° to 113°F (5° to 45°C)
Table 5-6. Minimum Propagation Delays (59Hz)
Input Output (ms)
525 720p59 1080i59 1080p29 1080p23
525 33.4 33.4 33.4 50.1 33.4
720p59 16.7 16.7 16.7 16.7 16.7
1080i59 33.4 33.4 33.4 33.4 33.4
1080p29 33.4 33.4 33.4 33.4 33.4
1080p23 41.7 41.7 41.7 41.7 41.7
XHD6801+ Installation and Operation Manual 67
Chapter 5: Specifications
Table 5-7. Minimum Propagation Delays (50Hz)
Input Output (ms)
625 720p50 1080i50 1080p25
625 40 40 40 60
720p50 20 20 20 20
1080i50 40 40 40 40
1080p25 40 40 40 40
68 XHD6801+ Installation and Operation Manual
Appendix A
Communication and ControlTroubleshooting Tips
OverviewFind the following troubleshooting information in this appendix:
• “Software Communication Problems” on page 70
• “Hardware Communication Problems” on page 73
XHD6801+ Installation and Operation Manual 69
Appendix A: Communication and Control Troubleshooting Tips
Software Communication Problems
The frame is powered up, but the module does not communicate with + Pilot Lite or CCS Pilot/Navigator.
Solutions• Ensure you have specified the proper module slot.
See your Frame Installation and Operation Manual for more information about slot identification.
• Verify whether you need an ICE6800+ or 6800+ETH module installed in the frame (not required for FR6822+).
• FR6802+ frames only use ICE6800+ modules to communicate with CCS software and hardware.
• FR6802+QXF frames use ICE6800+ or 6800+ETH modules to communicate with CCS software and hardware.
• Remove any legacy 6800 series product that is in the frame.
+ Pilot Lite and CCS software cannot communicate with legacy 6800 series products, even though these modules may operate with card-edge controls in an FR6802+ frame. Legacy 6800 products do not have the “+” symbol on their extractor handles.
• Check for bent pins on the back module by following this procedure:
a. Unplug the front module.
b. Unscrew and remove the back module.
c. Inspect the 20- or 30-pin spring connector at the bottom of the back module (Figure A-1 on page 71), and verify that the connector does not have any slightly bent or pressed pins.
d. Carefully reposition any bent pins; if this is not possible, contact Customer Support.
70 XHD6801+ Installation and Operation Manual
Appendix A: Communication and Control Troubleshooting Tips
Figure A-1. Typical Back Module Spring Connector
The frame is powered up, but + Pilot Lite does not communicate with the module.
Solutions• Ensure you have installed the correct cables between the PC and the
frame:
• A null modem serial cable must be used between a PC and an FR6802+ frame (not a straight-through cable). At minimum, this requires that pins 2 and 3 are crossed, but pin 5 (ground) is straight-through to pin 5.
• A USB cable must be used between a PC and an FR6802+QXF frame.
• Verify whether you need an ICE6800+ or 6800+ETH module installed in the frame.
• + Pilot Lite control is disabled if an ICE6800+ or 6800+ETH control module is installed in the frame.
• Set the Frame ID DIP switch settings correctly (the Frame ID DIP switch is located at the rear of the frame.)
• If only one frame is connected, set the DIP switch to 00.
• If multiple frames are used in a daisy-chain, set the DIP switch numbers consecutively to the following:
XHD6801+ Installation and Operation Manual 71
Appendix A: Communication and Control Troubleshooting Tips
• 00 (frame 1)• 01 (frame 2)• 10 (frame 3• 11 (frame 4)
See your FR6802+ Frame Installation and Operation Manual for more information about frame ID switch settings.
• Check that the correct COM port is configured in + Pilot Lite and that another application is not using that COM port.
+ Pilot Lite and CCS software see the frame, but do not find all of the modules
Solutions• Remove any legacy 6800 series products.
• Plug your modules in before starting the discovery.
• Start your discovery after the frame and all modules have fully powered up.
• Refresh + Pilot Lite (File > Refresh), and ensure that the installed modules are fully powered up first before discovery.
+ Pilot Lite and CCS Pilot/Navigator do not respond after they have been launched.
SolutionClose either + Pilot Lite or CCS Pilot/Navigator. Both programs cannot be running at the same time on the same PC.
+ Pilot Lite and CCS software show a module in the control window, but cannot control it.
Solution1. Set the module’s Local/Remote jumper to Remote.
2. Ensure the module name in the Control window matches the module type in the frame.
3. Gently push the module into its slot in the frame to ensure it is seated properly and powered up.
4. Verify that the Control window indicates the device is ready.
72 XHD6801+ Installation and Operation Manual
Appendix A: Communication and Control Troubleshooting Tips
Hardware Communication Problems
After a power failure, the frames and PC do not communicate.
Solution1. Wait four minutes for the frames to recover from the power failure.
2. Close the + Pilot Lite or CCS software, and then restart the PC.
3. Restart the software application.
The module does not seem to work.
Solutions• Ensure the correct frame is powered up.
• Verify that all appropriate rear connections are secure.
• Gently push the module into its slot in the frame to ensure it is seated properly.
• Ensure the back module does not have bent pins by following this procedure:
a. Unplug the front module.
b. Unscrew and remove the back module.
c. Inspect the spring connector at the bottom of the back module (Figure A-1), and verify the connector does not have any slightly bent or pressed pins.
d. Carefully reposition any bent pins; if this is not possible, contact Customer Support.
XHD6801+ Installation and Operation Manual 73
Appendix A: Communication and Control Troubleshooting Tips
74 XHD6801+ Installation and Operation Manual
Index
Keywords
AActive Format Description (AFD) 40–51AFD/ARC alignment 40Alarms list 61Applications for the module 5Aspect Ratio Conversion (ARC) 37–51Audio
configuration 53–55controls 53embedding and demuxing 53–55gain, bypass, and delay 54muting 54proc amp 54routing 53status parameters 55
Australian TV closed captioning 52
BBack module 8–9Bank Select LEDs 34Bypass control 43, 54
CCC Embed parameter 52CCS applications 32–33
refreshing and discovering modules 32troubleshooting 70–73
Closed captioning 52
Copyright information iiCorrecting failed upgrades 21–23
DDefault parameter settings 35Demux error parameters 55Demux parameters 53, 55Detection of AFD, VI, and WWS 42Discovering a module 33DVB Teletext captioning 52
EErrors in demux 55External reference termination jumper 15
FFirmware upgrading 18–23Frame power ratings 12Frame sync and scaled outputs 28–29Free TV Australia closed captioning 52Front module 6
GGain, bypass, and delay for audio 54Genlock specifications 65GPI
inputs and outputs 56pinouts 8
XHD6801+ Installation and Operation Manual 75
Index
HHD-SDI video input and output specifications 66
IInput/output audio delay jumper 16Installing and removing modules 17
JJumper settings 14–16
KKeying feature 56
LLEDs 6–7, 59–60License keys 17, 36Local/Remote jumper 14–15Loss of video (LOV) mode 27–29
MMain features 2Manual information vii–viiiModule
back 8–9front 6installation and removal 17status LEDs 60
Mux group parameters 54
NNavigating the parameter list 58Navigation Properties box 22
OOn-Screen display (OSD) 35, 58Operating notes 26
PPacking list 13Parameter
changes at card-edge 33–58settings 32–35
ParametersCC Embed 52demux error 55Demux Group and Channel Pairs 53Mux Group 54On-Screen Display 35SRC Input Select 53
Pilot Lite troubleshooting 70–73Pinouts, GPI 8Power ratings, frames 12Precautions, safety xiiProc amp, audio 54Processing modes 27–29Product servicing ix
QQ-SEE compliant thumbnails 30
RRecalling default parameter settings 35Reference termination jumper 15Refreshing a module with Pilot Lite 32Removing and installing modules 17Returning a product ixRevision history of the manual viiRoHS compliance x
SSafety precautions xiiSample rate converter 53–54Scaled outputs with re-clocked inputs 27–28SD/HD-SDI
reclocked video output specifications 66video input specifications 64
76 XHD6801+ Installation and Operation Manual
Index
Setting jumpers 14–16Shipping and unpacking a product ixSignal flow diagram 10Software
license keys 17, 36upgrading 18–23version number 35
Specifications 63–67SRC Input Select parameters 53Standards
RoHS compliance xSMPTE 52WEEE compliance xi
Streaming 30Support documents viii
TTeletext system 52Thumbnails 30Tone generators 54Troubleshooting 69–73
UUnpacking and shipping a product ixUnpacking the module 13Upgrading module software 18–23
VVideo Index (VI) 40–51Video keying 56Video processing modes 27–29Video streaming 30
WWarranty information iiWEEE compliance xiWide Screen Signalling (WSS) 40–51World System Teletext 52Writing conventions viii
XHD6801+ Installation and Operation Manual 77
Index
78 XHD6801+ Installation and Operation Manual
Broadcast Communications Division 4393 Digital Way | Mason, OH USA 45040 | Tel: 1 (513) 459 3400
www.broadcast.harris.com
©2011 Harris Corporation
Harris is a registered trademark of Harris Corporation. Trademarks and tradenames are the property of their respective companies.
Customer Service Support
+1 888 534 [email protected]