SECTION A

SPECIFICATIONS WURLITZER

AMERICANA SERIES 100 - 160 - 200 SELECTION PHONOGRAPHS

CABINET DIMENSIONS

Height - 52 1/4" Depth - 27 3/4" Width - 40"

. . . . DOME LOCK KEY RW 110

CASH BOX LOCK . . . . Ace WCX Ser ies

. . . . DOLLAR BILL CASH BOX LOCK Ace WCX Ser ies

POWER REQUIREMENTS Standby 117 Volts

60 Her tz 200 VA (120 Watts)

Operational 117 Volts 60 He r t z

360 VA (230 Watts)

CABINET ILLUMINATION 1 - 30" 18W and 1 - 33" 25W Fluorescent

CREDIT EQUIPMENT . . . . . . . . . . . . Slug Rejector National Simplex IV

. . . . . . . . . Dollar Bill Accepter National Buck Pas se r . . . . . . . . . . . . . . Credi t Unit Wurl i tzer Electronic Bonus Accumulator

RECORD CHANGER Wurl i tzer Wurlamatic Turntable Speed . . . . . . . . . . . 33.3 and 45 Automatic Intermixed

. . . . . . . . . . . . . . . Records 7" - 33 .3 and 45 RPM Record Libra ry

. . . . 100 Selection Phonograph 50 r eco rd capacity

. . . . 160 Selection Phonograph 80 record capacity

. . . . 200 Selection Phonograph 100 record capacity

WURLITZER Page B

SECTION A

KEYBOARD - 200 Selection Phonographs LP selections can be programmed in the A only o r A thru K sections 1 thru 0 . Minimum LP programming 5 LP records, 10 selections. Maximum LP programming 50 LP records, 100 selections . Automatic Programmer (when phonographs a r e s o equipped). Preset 1 Program selects records El-E3-E5 and F1-F3-F5, a l so E7-E9 and F7-F9

if s o des i red . Preset 2 Program selects records J1-J3-J5 and K1-K3-K5, a l so J7-J9 and K7-K9

if s o des i red . The Automatic Programmer can be optionally s e t for six, eight o r ten selections

in the E-F and J-K sect ions.

NOTE If the Phonograph is equipped with Preset Programs it is not advisable to place LP albums in the E, F, J o r K sections of the record magazine. However, LP Albums may be placed in the A, B, C, D, G and H sect ions.

KEYBOARD - 160 Selection Phonographs LP selections can be programmed in the 1 only o r 1 thru 8 sections A thru V. Minimum LP programming 10 LP records, 20 select ions. Maximum LP programming 80 records, 160 select ions.

KEYBOARD - 100 Selection Phonographs LP selections can be programmed in the A only o r A thru E sections 1 thru 0 . Minimum LP programming 5 LP records, 10 select ions. Maximum LP programming 25 records, 50 selections.

SOUND SYSTEM Solid State Amplifier . .. . . Wurlitzer Model 556 Power Supply . . . . Wurlitzer Model 561 Pickup . . . . Astatic Stylus . . . . Dual Tip Diamond .7 Mil Power Output total . . . . 80 watts music power Output Impedance . . . . Multiple tap low impedance plus constant voltage.

CABINET SPEAKERS 2 - 12" Lower - Range Speakers 2 - 6" Upper - Range Speakers

AMERICANA ACCESSORIES

Remote Volume Control Kit 2198 Microphone Kit 220A Stepper, 100 and 200 Selection, Model 270 Stepper, 160 Selection, Model 271 Bill Validator (Buck Passe r ) Kit 235 Income Computer Model 242 Income Computer Model 243 ( Less Printout) Mounting Bracket Kit 226 ( F o r Model 225 and 236 Income Computers )

Part No. 141186 Part No. 138847 - Part No. 138849 Part No. 138850 Part No. 140930 - Part No. 143764 Part No. 143765 Part No. 138845 -

Page C WURLITZER

SECTION A

Wall Box, 200 Selection ( w i t h Speakers & Golden Bar), Model 5220L P a r t No. 125555 Wall Box, 200 Selection (without Speakers o r Golden Bar) , Model 5220AL P a r t No. 125557 Wall Box, 100 Selection (wi th Speakers & Golden Bar) , Model 52251, Pa r t No. 125547 Wall Box, 100 Selection (without Speakers o r Golden Bar) , Model 5225AL P a r t No. 125549 Wall Box Booster T r a n s f o r m e r , Model 222C P a r t No. 137182 Speaker, Wall, Rectangular Type, Model 5127 P a r t No. 140288 Speaker, Wall, Wedge Type, Model 5128 P a r t No. 140289

- WURLITZER

Page D

SECTION A

COlN AND CREDIT EQUIPMENT

. .. .. hhlh.l.wG CAW

SLUG REJECTOR

ELECTRONlC BONUS ACGU~L1CATOR

Reject Rod Adjustment

Slug Rejector Mounting Plate Adjustment

C o b Switch Adjustments

Electronic Bonus Accurnularor

Slug Rejector Mounting Assembly Illustrated Parts List

Page 2A

Page 2A

Page 3A

Page 4A

Page 5A

WURLITZER Page 1A

SECTION A -

REJECT ROD ADWTMENT - Open phonograph dame assembly and remove the program holder, then close dome assembly. - Depress rcject button firmly. Viewing SLUG REJECTOR through the dome assembly, verify that the BRACKET and CAM ASSEMBLY is ful ly depressed with 1/4" of the reject button remaining.

- Should adjustment of f he REJECT ROD be necessary, loosen REJECT ROD ADJUSTING NUTS and posit ion the REJECT ROD as required fo r proper operation. Tighten REJECT ROD ADJUSTING NUTS.

SLUG REJECTOR

REJECT ROD ADJUSTING NUTS

REJECT ROD

' RETAINING SPRING - /

k MOUNTING SCREWS (Typical) -

- -, BRACKET and

CAM ASSEMBLY -

1 SLUG REJECTOR -

\ MOUNTING PLATE

ANGLE and - GUARD ASSEMBLY

- SLUG REJECTOR MOUNTING PLATE ADJUSTMENT

Be sure that the phonograph is positioned on a level surface pr io r to making any adjustments to - rhe SLUG REJECTOR MOUNTING PLATE. Should it be necessary to compensate for uneven footing, t h e following methods may be used.

- 1. Side ta s i d e Ieveling of the plronograph may be accomplisl~ed by placing blocks o r strips

under the casters on t h e low side of the cabinet. Check SLUG REJECTOR fo r proper coin acceptance. -

2 . FronttabacklevelingoftheSLUGREJECTORmaybeaccomplishedbylooseningthe seven MOUNTING SCREWS and positioning the SLUG REJECTOR MOUNTING PLATE as -

Page 2A WURLITZER

- SECTION A

required. Tighten MOUNTING SCREWS. Check SLUG REJECTOR f o r proper coin acceptance.

NOTE Access to all MOUhTING SCREWS is accomplished by lifting the RETAINING SPRING, moving the top of t h e SLUG REJECTOR to the left then lifting out.

COIN SWITCH ADJUSTMENTS

Rem

A .

ove ANGLE and GUARD ASSEMBLY t o obtain access to coin swi tch. --- ---- - - -

With coin switch paddles res t ing flush against bottom of slug rejector, vex ify spacing bemeen swirch mounting bracket and cover and clip assembly is l j 4 " .

Tension of the long movable blades must be sufficient to hold the coin sw itch paddles against bottom of slug cejectar .

The stiffener blades should be set to / provide -060 to ,070 opening between contacts of shor t and long movable contact b lades .

- D . The shor t bhdes must bear against

stifEeners with suffic rent tens ion to nrevent vibration. This should be I

C

1 1/2 ta 2 grams on the 5, 10 and 25 cent blades and 3 to 5 grams on the

- 50 cent blade.

- The tension of the long movable blades should be adjusted so a thin coin, when stopped on it's coin paddle by holding t h e paddle up, wil l upon releasing t h e paddle, actuate the movable bIade, close the contacts then clear paddle.

- 1 . Install SLUG REJECTOR ia pilonagraph and apply power .

- 2. Test each individual coin track ten consecutive times with coin of varied wear. If a coin faiIs to register, that pa r t i cu la r coin switch should be examined and, if necessary,

rcadjus ted , Check SLUG REJECTOR for proper alignment.

- ELECTRONIC BONUS ACCUMULATOR

- The Electronic Bonus Accumulator, hexeinafter rererred t o as BO/AC, is a solid stare electronic credit accumulator designed t o provide a method of credit accumulation, both standard and bonus, resulting f rom the depos icing of coinage of all denominations . It

- w i l l also accumulate credits resu king from the depositing of dollar bills in Phonographs

WURLITZER Page 3A

--

SECTION A

equipped wit11 Dol l a r Bi l l Accepters . The coins - and/or dollar bills may be deposited in any sequence u n t i l rnaxinlun credits have been accum- ulated t o permit: the selection of thirty-one standard plays . The amount of credits required f o r each standard play are governed by the plug In Program Card.

Program Card, Part No. 138342, is supplied with the BO/AC . Any combination of coinage equalling

a .25, -50, .75 or 1.00, u s i n g this Program Card, w i l l provide t h e following:

a . Singles - Two f o r -25, five for .SO, eight f o r .75 and twelve f o r 1 .00.

b . LP's - One for .25, two f o r .SO, three for .7 5 and l o u r for 1.00, provided the Pl~oaograpb is programmed f o r LP's and t he Conversion Plug, located on the Selector Switch Assembly,

a,-,gr 'd is set: up for LP's . c . Six, eight o r ten preselected singles for .50

provided the Phonogxaplz is equipped to play preselected programs ,

Should a pricing change be desired, addicional Programs are available t l~rough your local Wurli tzer Distributor. Access to t h e Program Card, installed i n the BO/AC, is obtained by removing the PRICE AND BONUS PROGRAMMING CARD Cover located on the Cover 01 t h e BO/AC.

NOTE

The base of the Program Cards are slotted to prevent improper insertion when installing Program Cards in the BO/AC .

A list of additional Coin Denomination Labels may be found on Page 8D of t h i s Service Manual. This list provides the Deposit Instructions, Coin Denomination Label Part Numbers, Pricing, Selections, and Program Card Part Number for each Coin Denomination Label.

Page 4A WURLITZER

1. Cover and Clip Assembly - Cable Clamp (2)

2. Locating Pin and Catch Assembly 3 . Actuator, Reject Button

- 4 . Pivot Pin, Lever Spring, Actuator Retaining Ring (2)

5 . Pivot Bracket and Bracket Assembly .-.. 6 . Pivot Shaft Retaining Ring

7 . Support Bracket, Reject Rod - 8 . Spring, Return, Reject Rod 9 . Reject Rod

Keps Nut, 1/4-20 Nut, 1/4-20 - Lockwasher

10. Coin Entry Chute Spacer (4) Screw, 8-32 x 1/2 HEX SWAGE

11. Mounting Bracket, Lower 12 . Retaining Ring, Slug Rejector

Washer -

SECTION A

1 3 . Mounting Plate and Bracket Assembly 140711 14. Mounting Plate, Slug Rejector 138189 1 5 . Angle and Guard Assembly 138235

Thumbscrew (2) 35745 1 6 . Coin Switch 131186

Plug, 9 131174 Pin Termina l (5) 132000 Lockwasher (2) 73604-5 Screw, 6 x 5 HEX Z (2) 76626-5 Speednut 74750-5

1 7 . Mounting Bracket and Guard Assembly 138233 Washer (2) 54024

18. Shaft 119107-C 19 . Copper Washer 119107-F 20. Long Paddle -119107-A 21. Spacer 119107-D 22. Copper Washer 119107-F 23. Copper Washer 119107-F 24. Short Paddle -119107-B 25. Iron Washer 119107-E 26. Iron Washer 119107-E

WURLITZER

-

SECTION B

- KEYBOARD SELECTOR SWITCH ASSEMBLY

L . - ; b 8 , *; LZK-L- . . r.<YY tr ..,,, ,-. ... . - . I, .. il

i CONTROL BOX (.I

SELECTOR SWITCH AND ELECTRIC SELECTOR

Connector Link Plate Ad jus t rnent

Latch Solenoid Stop Bracket, h t c h SoIenoid and Latch Solenoid SW itch Adjus tment

Letter and Number Latch Lever Adjustment

Letter Series Switch Adjustment

Letter and Nctmbcr Latch Switch Adjustment

Conrral Box Assembly PIlustrated Parts List

Printed Board Assemblies - Control Box

Selector Switch Assembly llluscratcd Parts List

Mounting Bracket, Switch and Cable Assembly Tllus trated Parts List

Page 3 B

Page 48

Page 5R

Page 6B

Page 7B

Page 8B-10B

Page 1 1 B

Page 1 4 B

WURLITZER Page 18

SECTION B

CONNECTOR LINK PLATE ADJUSTMENT

A . Loosen the LETTER and NUMBER LATCH LEVER ADJUSTING SCREWS.

NUhdBER LATCH LEVER ADTUSTING SCREW

\ LETTER LATCH LEVER 4- ADJUSTING SCREW - p r ,r 3 1

a L,

i

Ra-

B. Loosen NUMBER and LETTER CONNECTOR LINK PLATE ADJUSTING SCREWS.

NUMBER CONNECTOR LETTER CONNECTOR LINK PLATE ADJUSTING LINK PLATE ADJUSTING SCREWS

NUMBER LINK and LETTER LINK and LEVER ASSEMBLY LEVER ASSEMBLY

C . Fully depress a number button, then D. Fully depress a letter button, then position the NUMBER LINK and LEVER position t h e LETTER LINK and LEVER ASSEMBLY in a vertical pes ition. ASSEMBLY in a vert ical pos ition. Tighten the NUMBER CONNECTOR Tighten the LETTER CONNECTOR LINK PLATE ADJUSTING SCREWS. LINK PLATE ADJUSTING SCREWS.

Page 2B WURLETZER

SECTION B

LATCH SOLENOIlJ STOP BRACKET, LATCH SOLENOID and LATCH SOLENOID SWITCH ADJUSTMENT

A . Verify that the RE LEASE LEVER is in B. Loosen the LATCH SOLENOID STOP its normal rest position. BRACKET ADJUSTING SCREWS.

LATCH SOLENOID STOP LATCH LATCH SOLENOID BRACKET ADJUSTMG S 0 LE NOT' SWITCH ADJUSTING ACTUATOR SCREWS \SWITCH \ SCREWL4

- 7 - - - - LATCI-I SOLENOID M T C W SOLENOID STOP BRACKET -

LETTER LATCH LEVER \./

1/64" t o 1/32" CLEARANCE

*:,- ADJUSTING SCREWS

8

- RIGHT HAND * ' I ! j TRIP LEVER

#

k 1/64" t o 1 /32Ir

LEFT HAND ' / CLEARANCE TRIP LEVER

RELEASE RELEASE LEVER NUMBER LATCH LEVER ADJUSTING SCREW LEVER

C . Loosen LATCI-I SOLENOID SWITCH D . Position LATCH SOLENOID STOP ACTUATOR ADJUSTING SCREW. BRACKET to provide 1/64" t o 1/32"

CLEARANCE between s f x d of the LEFT HAND TRIP LEVER and the stop pad of the LETTER LATCH LEVER.

E. SettheLATCI-TSOLENOTDSWPTCR F. AdjusrtheRELEASELEVERADJUSTLVG button in t h e emerne left position SCREW as necessary to provide 1/64" then positian the right: hand tab of the t o 1/32" C L E A U N C E between t h e SOLENOID SWITCH ACTUATOR firmly square stud of the NUMBER LA TCH against the LATCI-I SOLENOID SWITCI-I LEVER and the RIGHT HAND TRIP button. Tighten SOLENOtD SWITCH LEVER, ACTUATOR ADJUSTING SCREW,

G . Loosen the LATCH SOLENOID ADJUS- H . Manually bottom the LATCH SOLENOID T l N G SCREWS. PLUNG ER and adjust the LATCI-I

SOLENOID t o position t h e LATCH SOLENOID SWITCH button t-o t he extremen right. Tighten LATCH SOLENOID ADJUSTING SCREUrS .

NOTE: Excercise extreme case not to over -travel t h e LATCH SOLENOD SWITCIi when performing Step H to preclude damage to the switciz . WUIILTTZER Page 3 B

SECTION B

LETTER AiiD NUMBER LATCH LEVER ADJUSTMENT

Verify that the LETTER and NUMBER LATCH LEVER ADJUSTING SCREWS are loose, then manually or electrically actuate the LATCH S OLENOZD . A . Manuallyholdalet terbuEtonful ly 8 . Maintain the setting of Step A and

depressed, then adjust the LETTER tighten t he LETTER LATCH LEVER U T C H LEVER so that its s top tab ADJUSTING SCREW. Check each letter rests firmly against t h e square stud buttoo far proper latching and selector of the LEFT HAND TRIP LEVER, switch contact engagement.

LETTER LATCH NUMBER U T C H LEVER

a LETTER LATCH LEVER <I , -

LATCH SOLENOID

LEFT HAND RIGHT HAND NUMBER LATCH TRIP LEVER TRIP LEVER LEVER

C . Manually hold a number button fully D. Maintain the setting of Step C and depressed, then adjust the NUMBER tighten the NUMBER LATCH LEVER LATCH LEVER so that the square s t u d ADJUSTING SCREW. Check each of the NUMBER LATCH LEVER rests number button for proper latching and firmly against the stop tab of the selector switch contact engagement. RIGHT HAND TRIP LEVER.

Page 4B WURZITZER

SECTION B

r l . Tlisconnecl blue plug froin C:ONTROL 13. Manually acluatc a letter button ant1 BOX Rcccpraclu located on Power verify tllat LE1"I'E R SERIES S WT'I'CH

Supply. upens t o provide 1 / 3 2 " 111 ~ I I in1 ~1111

hT0UNTLNG clearance between swi tch contacts.

SC IIE WS

ADJWSTTNG SCREWS

LETTER SERIES SWITCI-1

UTCI.1 S 0 LENOID

LETTER LETTER LA-I'CH LATCH SWITCH LEVEK

LATCI-I SOLENOm PLUNGER

C . Rt.lcase letter h u t ~ o n a n d vcrify L I I ~ L D . Should adjustnlcnr be necessary, loosen I-E'TTER SEIilES SWITCI I closes W it11 .LETTER SERIES SlVITCH ADJL7S'TI;iG 1/,32" rninil-r~urn wipe ( ovr_'rtravel) on SCREWS a n d ~ d j u s t LETTER SERIES closed con t a c ~ s . SWITCH ro sarisly requirerneeits of

Steps I3 and C: .

SUTE: If fuel her acljusrmer-tr is necessary, LETTER SERIES SWITCH bbdcs rliay be refor~nerl to sa~isfy req~iire~nents of Steps 13 a n d C ,

E . Tigliren LETTER SE RIES SirlTC11 F . Manuall!? actuarc a lelrer button mlcl :tD]LJS 1-IXG SCREWS , verify that long hlaclc of LE7'1'ER

SERIES SWITCI! is centerecl o11 Phonolic Collar tlf LETTER Lh'1'C:FI LEYER.

C; . Should r~djusrrne~rL bc ~loucssary, l u o s c ~ ~ 1-1 . -1'igh~en LET-FE R S WI-I'CH hlOUN'l'ING LETTE R SE 1x1~s S ~ I - ~ C T I MOIJNTING SCREWS. SCREWS a n d adjust blades of I,E'I"I'ER SERIES SWITCH ta snrisi)t rcrlui 1-ctnerlr of S lep I:.

I . I?cc.o~~norl ll lue plug, disconnoctcil i n Step A , 011 CON'I'RUL UOX IEi.c.cptacl~ ltrcaletl olr Power Supylly.

NOTE

When a Iener burton is latched, tllc contacts of t h e LETTER SERIES SWITCHES should open 1 J32" a ~ c l shauld close w it11 1/32" overtravel when the button is released.

WURLITZER Page 5B

SECTION B

LETTER AND NUMBER LATCH SWITCH ADJUSTMENT

A . Loosen t h e LETTER and NUMBER B . Manually hold the LATCH SOLENOID M T C H SWITCH ADJUSTING SCREWS. PLUNGER firmly bottomed in the

LATCH SOLENOID.

LETTER LATCH SWITCH ADJUSTING SCREWS \

LETTER LATCH \ '

/

LEFT FUND RIGHT HAND NUMBER LATCH TRIP LEVER TRIP LEVER 1 ' SWITCH

LATCH SOLENOID

LATCH SOLENOLD PLUNGER

NUMBER LATCH SWITCH ADJUSTrNG SCREWS

C . Adjust the LETTER LATCH SWITCH a. Adjust the NUMBER LATCH SWLTaI so that the long blade of the swi tch so that the long blade of the switch rests against the insulated s tud of the rests agalnst the insulated stud of the LEFT HAND TRIP LEVER with zero RIGHT I-LAND TRIP LEVE R w ith zero clearance , Tighten LETTER LATCH cloasance . Tighten t h e NUMBER SWrrCH ADJUSTDlG SCREWS. LATCH SWRCH ADJUSTING SCREWS .

NOTE T't~e contacts of the LETTER and NUMBER LATCI-J SWITCHES are set normally open 1/32". When a letter and /o r number button is latched, the contacts of their respective switches should close with 1/32" overtravel.

Page 68 WURLITZER

SECTION B

7

C O N T R O L BOX ASSEMBLY ILLUSTRATED PARTS LIST

I . Thunibscrew Retainer

2 . Cover , Prinred Board, Control Box 3 . Printed Board, Control Box 4 . Rciay, Red ( R Y - 1 2 )

I-lolddown Spring Receptacle, Relay, Red Termina l , Relay Socket

5 . Receptacle , 12W ( n o t shown) Receptacle, 15W ( (not shown) Contact 1-erminal ( 2 6 ) J u m p e r Plug Assembly, Stepper Pin Termina l ( 9 )

6 . Cover Plate, Vent 7 . Receptacle, 9R

Contact Termina l ( 7 ) 8 . Receptacle, 12R

Contact Termina l ( 8 ) 9 . Receptacle, 36 Min.

Contact Termina l ( 31 ) 1 0 . Receptacle, 15R

Contact Termina l ( 1 2 ) 11. Plug, 120

Pin Termina l ( 1 2 ) 12 . Receptacle, 15W

Contact T e r m i n a l ( 1 3 )

13 . Receptacle, 12W 131175 Contact Termina l ( 7 ) 132001

14 . Receptacle, 24 Min. 657711 Contact Termina l ( 2 4 ) 138558

15 . Relay, White (RY-I .RY-2. RY-3, RY-6, RY-7. RY-10, RY-11, RY-20 , RY-21, RY-22,RY-23, and RY-24) 122133

Holddown Spring, Relay 134840 Receptacle, Relay, White 1363.36 Termina l , Relay Socket 136335

1 6 . Pin, F a l l Support 137083 Retaining Ring 73724-18

17 . F u s e Post 126853 Loc kwas h e r 73607-13 Fuse , 8A, Slo Blo 71591-34

1 8 . C i rcu i t B r e a k e r ( 2 ) 140507

19 . Receptacle, Relay, 6 Pole 138719 20. Relay, 6 Pole 138716

Relay Spring, 6 Pole 139162 21. Remaining Control Box Components,

( R e f e r to Page SB-11~ )

WURLITZER Page 7B

-~ -

SECTION B

136853

140769 (REF.)

VIEW IS B TYPICAL 3 PLACES

~ -

TRANSISTORS ITEM NO. I PART NO. I TYPE

PRINTED BOARD ASSEMBLY - TRIAC CONTROL - PART NO. 140764

RESISTORS

TR2 and 4

Page 8B

PARTS LIST ITEM NO.

RI, 6 and 11

R2,7and12 R3 and 8 R4, 5, 9 and 1 0

C1, 2 and 4 C:3

ITEM S O . D l 0 and I1 Opt .

CONTROL BOX COMPONENTS NOT ILLUSTRATED

WURLITZER

PART NO. 141073 140769 76989-3 76983-4 76983-5 76719-25 133141 73607-3 136853

PART NO.

76980-15 141494 76984-3 76984-4 76984-5 139139 140624

NAME

Printed Board and Eyele t Assemb ly T r i a c and Heats ink Assemb ly W a f e r C r ~ n n e c t u r Wafe r Connec tor Wafer Connec tor Sc r cw , 4-40 x 3 /8 TRUSS Washer Loc kwasher Nut, 4-40

JUMPER ITEM NO. I PART NO. I NAME 11 1 112721 I Wire Fortiled

PART NO.

74544.32 72312-32 77293-255 77311-255

76195-14s 76203-17s

PART NO. 76700-23 76700-33

NAME

Space r ( 4 ) Insu la tor Ha rnes s Connec tor Ha rnes s Connec tor Ha rnes s Connec tor T e r m i n a l ( f o r 76984 Connec tors ) NPN-Silicon-Planar

VALUE

680 OHM 2W 1 0 % 100 OHM IW 10%

1 K 1/4W 5 % 5 . 6 K 1/4W 5%

CAPACITORS

.1 MFD 400V' .22 M F D 75V

DIODES TYPE

Rect i f ie r 1N4004 Rect i f ic r 10D4

- ~

SECTION B

DIODES - ITEM NO. I PART NO. I TYPE - Dl thru D4 1 76700-23 1 Rectifier IN4004

PRINTED BOARD ASSEMBLY - TIMING PART NO. 140756

76700-33 71588-21 71588-22 128449

TR1,2 and 5 137480 140624 140623 132650

,

,

Rectifier 1 0 D 4 Rectifier DO-I . Rectifier Zenner Diode IN4758

NPN-Silicon-Annular NPN-Silicon-Planar PNP-Silicon-Planar UNIJ-Silicon-Unij~lnction

R9 77281-255 330 OHM 1/4W 5% - R l O a n d l l 77269-255 100 OHM 1/4W 5% - R12 77345-255 150 K 1/4W 5%

R13 72332-32 680 OHM 1W 10% R14 77341-255 100 K 1/4W 5 %

CAPACITORS

- C1 77510-2 100 MFD 16V , C2 77513-6 470 MFD 50V

C3 77507-3 22 MFD 16V e C4 77509-3 47 MFD 16V

RESISTORS

Harness Connector Terminal ( f o r 76984 Connectors )

PARTS LIST

WURLITZER

PART NO. 140758 76983-3 76983 -5 76983-6

VALUE

1 . 5 OHM 8W 5% 1 . 2 K 1/4W 5%

1 K 1/4W 5% 1 0 K 1/4w 5%

5 . 6 K 1/4W 5%

ITEM NO.

R1 R2 , R3 and 8 . R4

R5,6and7

NAME Printed Circuit Board Wafer Connector Wafer Connector Wafer Connector

PART NO.

76972 77295-255 77293-255 77317-255 77311-255

SECTION B

PRINTED BOARD ASSEMBLY - VOLTAGE REGULATOR - PART NO. 143062 .& - RESISTORS

C37 77513-6 470 MFD 50V

DIODES

- ~

R33 R34

R35 S E L .

R36

I TRANSISTORS 1 VALUE ITEM NO. PART NO.

C31 77391-433 .22 MFD DISC - C32 77513-6 470 MFD 50V -C33 76948-2 1 0 MFD 15V

C34 77391 -433 .22 MFD DISC C35 77391 -433 .22 MFD DISC C36 77948-2 1 0 MFD 25V

77241-253 77294-253 77313-253 77315-253 77317-253 77319-253 77294-253

ITEM NO.

TR31

TR32 and

TR33

6.8 OHM 1/4W 5 i 1.1 K 1/4W 5% 6 .8 K 1/4W 5 % 8.2 K 1/4W 5 %

1 0 K 1/4W 5% 12 K 1 / 4 w 5 %

1.1 K 1/4W 5%

CAPACITORS

PART NO.

VR1 OPT.

NAME

PRINTED CIRCUIT BOARD, VOLTAGE REG.

SCREW, MACHINE, TRUSS HEAD WASHER LOCKWASHER, INTERNAL NUT, 4-40, BRASS SCREW, SEMS, RD. HD. ( 2 ) KEPS LOCKWASHER AND NUT ( 2 ) WAFER CONNECTOR SPACER ( 4 )

VOLTAGEREGULATOR

PART NO.

143201

140623

Page 10B

TYPE

TRANSISTOR ANS HEAT SINK ASSEMBLY

PNP-SILICON-PLANAR

PARTS LIST

142130 143076

WURLITZER

+12V +12V

SECTION B

PRINTED BOARD ASSEMBLY - PART NO. 141107

PRINTED BOARD ASSEMBLY - PART NO. 141108 -

-

PARTS LIST DIODES PART NO.

1407 47 76980-12 138872

ITEM NO.

D7 Opt. D:3O tllru34 Opt.

NAME

Printed Board and Eyelet Assembly

Spacer ( 3 ) (no t illustrated ) Insulator ( not i l lus t ra ted)

- -

PART NO.

76700.23 76700.33 71588-21 51588.22

*-

WURLITZER

TYPE

Rectif ier IN4001 Rectif ier 10 D4 Rectificr-Silicon DO-1 Rectifier-Silicon

DIODES ITEM NO. PART NO. ( TYPE

D7 tliru 8 / 76700-2.3 1 R c ~ t ~ f ~ e r IN4004

PRINTED BOARD ASSEMBLY - PART NO. 141109 -

Page 11B

PARTS LIST PART NO. ( NAME

140839 I Prknted Board and Evelet Assemblv Opt . 1)30t!iru :34 Opt .

- ' -

76700-:1:3 71588-21 71588-22

DIODES ITEM NO.

D7 tliru 2:1 Opt. 1130thru34 Oilt .

Rectifier 10 D4 Rectifier-Silicon DO-1 Rcctifier-Silicon

PART XO.

76700-23 76700-:<:I 71588-21 71588-22

-

TYPE

Rectif ier I N-1004 140842 Printed Board and Eyelet Assembly

Rectifier 10 D4 Rectifier-Silicon DO-I 10887.2 Rectificr-Silicon

J

76980.12 138872

- - ~

Spacer ( 3 ) (no t illustrated ) Insulator ( not i l lus t ra ted)

SECTION B

WURLITZER

- -

- SHIELD AND CABLE ASSEMBLY - S E L E C T O R SWITCH ASSEMBLY

+ I . Shield and Insulator Assembly ( 2 ) Lamp ( 20 )

2. Selector Button and Clip Assembly, A Selector Button and Clip Assembly, B

r- Selec to r Button and Clip Assembly, C

Selector Button and Clip Assembly, D Selector Button and Clip Assembly, E - Selector Button and Clip Assembly, F Se lec to r Button and Clip Assembly, G Selector Button and Clip Assembly, H Se lec to r Button and Clip Assembly, J - Selector Button and Clip Assembly, K Se lec to r Button and Clip Assembly, L Selector Button and Clip Assembly, M Selector Button and Clip Assembly, N

7 Selec to r Button and Clip Assembly, P

Selector Button and Clip Assembly, Q Selector Button and Clip Assembly, R Selector Button and Clip Assembly, S - Selector Button and Clip Assembly, T Selec to r Button and Clip Assembly, U Selector Button and Clip Assembly, V - Cap Only Inser t Clip Only

3. Button and Clip Assembly Reset - Cap Only

Inser t Clip Only

4. Stop Bracket - Switch, Reset

5. Selector Button and Clip Assembly, 1 Se lec to r Button and Clip Assembly, 2 - Selec to r Button and Clip Assembly, 3 Selector Button and Clip Assembly, 4 Selector Button and Clip Assembly, 5 Selector Button and Clip Assembly, 6 - Selector Button and Clip Assembly, 7 Se lec to r Button and Clip Assembly, 8 Se lec to r Button and Clip Assembly, 9 Selector Button and Clip Assembly, 0 - Cap Only Inser t C l ~ p Only

- Complete Set Se lec to r Button and Cllp Asscrnbly 6. Shield and Insulator Assemblv

Lamp ( 1 0 ) - Diode ( 1 0 ) - 7. Plug, 15W

Pin Termina l ( 3 ) 8 . Plug, 15B

Pin Termina l ( 15) 9. Mounting Plate

Light Shield, R.H. Light Shield, L.H. - 10. Light Diffuser

11. Selector Switch, Numbers

SECTION B

WURLITZER

- ILLUSTRATED

200

,140576 136858 143002 143003 143004 143005 143006 143007 143008 143009 143010 143011 143012 143013 143014 143015 143016 143017 143018 143019 143020 143021 142649 142650 131909 143032 143456 143455 131909 139831 139837 143022 143023 143024 143025 143026 143027 143028 143029 143030

Page 138

PARTS

160

143002 143003 143004 143005 143006 143007 143008 143009 143010 143011 143012 143013 143014 143015 143016 143017 143018 143019 143020 143021 142649 142650 131909 143032 143456 143455 131909 139891 139837 143022 143023 143024 143025 14:3026 143027 143028 143029

LIST

100

143002 143003 143004 143005 143006 143007 143008 143009 143010 143011

142649 142650 131909 143032 143456 143455 131909 139831 139837 149022 143023 149024 143025 143026 143027 143028 143029 143030

-

SECTION B

- SHIELD AND CABLE ASSEMBLY - SELECTOR SWITCH ASSEMBLY - ILLUSTRATED PARTS LIST (Cont'd .)

12. Electr ic Counter 1 3 . Receptacle, 9W

Contact T e r m i n a l ( 9 ) 1 4 . Gusset , R .H. 15. Crank and Link Assembly - Retaining Ring - Retaining Ring

--. 1 6 . Latch Solenoid Plunger, -Solenoid Pin, Solenoid Plunger

wasF . . Internal I-la11 Pin

1 7 . Mounting Bracket, Latch Solenoid Washer ( 2 )

- 18. Switch Assembly Retainer Plate Mounting Bracket

19. Switch and Bracket Assembly 20. Switch Actuator 21. Latch Lcver , Numbers

Washer 22. T r i p Lever , R.H., Xumbers

Stop Nut, 10-32 Was tier ( 2 ) Washer Spring, T r i p Lever , R.H.

23. T r i p Lever , L.H., Le t te r s Spacer - Spring, T r i p Lever , L.H. - 24. Switch Assembly Retainer Plate Mounting Bracket

ALL MODELS

143398 25. Switch and Bracket Assembly, Ser ies 131173 Le t te r s 132001 .-Switch Assembly 140544 -Mounting Bracket 111720 Retainer

73724-15 26. Cover and Clip Assembly 73724-18 27. Release Lever

112104 Washer 112104-1 Spring, Solenoid Return

65947 -28. Latcli Lever , Le t te r s 487 Washer

74402-1 -29. Receptacle, 15W 117747 Contact Termina l ( 12 ) 54024 30. Stop Bracket 60518 Washer ( 2 ) 63014 Rubber Grommel

121005 -31. Res i s to r , 85 Ohm, 5W 140170 -32. Diode ( 3 ) 140070 33. Gusset , L.H.

64913 34. Plug, Molex, 24 73608-45 Pin Termina l ( 21 )

117694 35. Plug, Molex, 36 74988-14 Pin Termina l ( 2 9 )

67610 36. Se lec to r Switch, Le t te r s 3800-3860 56733 Se lec to r Switch, Le t te r s 3810 57129 37. Snap Bushing ( 2 )

117691 1 3 8 . Connector Link Plate ( 2 ) 57790 Spacer , Link, Se lec to r Switch ( 4 )

120067 - Spacer , Shoulder Bushing, Link ( 2 ) 60518 Washer ( 4 ) 63014 -39. Connector Link ( 2 ) 3800-3860

121005 Connector Link ( 2 ) 3810 - Shoulder Bushing, Link ( 4 ) W a s h e r ( 2 )

40. Shaft, Link and Lever Assembly 41. Shaft, Link and Lever Assembly

- WURLITZER

SECTION C

RECORD CHANGER ADJUSTMENTS

, 1111

. * . ' ll~~ll#\'~l~\~[ii~ ' " ' I -.. - J --. . ' . I - .

I - , -.' t ' '. .

Page I C

SECTION C

INDEX T O ADJUSTMENTS

Selection Accumulator Adjustment

Shaft and Magnet Arm Assembly Adjustment

Override Assembly Adjustment

Magazine Lock Switch Adjustment

Magazine Drive Motor Adjustment

Side 1 Cancel Solenoid Adjustment

Digital Record Now Playing Indicator Adjustment

Side 1 and 2 Readout Switch Adjustment

Safety Switch Adjustment

• Bail and Bushing Assembly Clearance Adjustment

Main Cam Motor Brake Adjustment

Transfer Switch Adjustment

Cancel Switch Adjustment

Record Takeout A r m Alignment

Playmeter Reset Magnet Adjustment

Side 1 Shift Adjustment

Turn Arm Holdout Cam Adjustment

Record Takeout Arm Turn Adjustment

Record Takeout Arm Stop Adjustment

Turntable Drive Wheel Adjustment

Turntable Speed Change Adjustment

Tone Arm Lift Adjustment

Stylus Brush Adjustment

Tone Arm Release Adjustment

Tone Arm Feed-In and Tr ip Switch Adjustment

Play Switch Adjustment

Stylus Pressure Adjustment

Turntable Pilot Reset Adjustment

Safety Circuit Adjustment

Page 4C

Page 4C - Page 5C

Page 8C -

Page 8C -

Page 9C

Page 10C -

Page 10C

Page 13C - Page 14C

Page 14C - Page 15C

Page 16C .-..

Page 17C

Page 18C - Page 18C

Page 20C - Page 21C

Page 21C - Page 22C

Page 23C &

Page 24C

Page 25C - Page 26C

Page 26C .-. Page 27C

Page 28C - Page 29C

Page 29C .-

- WURLITZER

SECTION C

The following procedure wi l l provide access to the lower side d the RECORD CHANGER:

A . Unlock and raise the UPPER DOOR ASSEMBLY t o its full height.

Disconnect the SERVICE DOOR SPEAKER and U M P PLUGS.

Unhook the two SERVICE DOOR FALL SUPPORT CI-IAINS at the cabinet end . Lift the SERVICE J300R out af the c alsinet .

L,.: - ++

4 ' -

E. Remove the two WING NUTS to free the RECORD CFIANGER.

F. Pul l the RECORD CHANGER forward, then lift the fsont of the RECORD CHANGER. The spring loaded PALL SUPPORTS wi l l drop into position to support the RECORD CHANGER.

- G . To return the RECORD CHANGER t o its normal operating position, lift the front a£ the RECORD CHANGER then depress t h e FALL SUPPORT EXTEN- SIONS a n d lower the RECORD CI-IANGER. Push the RECORD *

; *: CHANGER back t o its normal oper- @ - ating position and reinstall the two

WING NUTS removed in Step E.

WURLITZER Page 3C

SECTION C

SE LECTION ACCUMULATOR ADJUSTMENTS

DIRECTION OF RUTATION SELECTION ACCUMULATOR

W G N E T LAMINATION MOUNTING SCREWS

SHAFT and MAGNET ARM ASSEMBLY

CONTACT PLATE and BLADE ASSEMBLY

CONTACT PLATE and BLADE ASSEMBLY MOUNTING SCREWS

SELECTOR LATCI-I PLN A-1

SHAFT AND MAGNET ARM ASSEMBLY ADJUSTMENTS

A . Rotate SHAFT and hL4GNET ARM 8. If vertical alignment caonat be obtained, ASSEMBLY in a clockwise direction loosen MAGNET LAMINATION and vertically align the leading edge MOUNTING SCREW and align MAGNET of the MAGNET LNdINATIONS with W I N A T I O N S t o meet requirement the leading edge of SE LECTOR of Step A . Tighten MAGNET L A W - LATCI-I PIN. ATION MOUNTING SCREW.

NOTE: SELECTOR SELECTOR LATCH PIN

LATCH PINS and SPACER have been removed to clariEy adjustment MAGNET

procedures only. LAMINATIONS

MAGNET LAMINATION MOUNTING SCREW

Page 4C WURLITZER

SECTION C

C . Verify that: OUTER CONTACT BLADE D. I£ requirement of Step C cannot be obtained, is adjacent to leading edge of the loosen CONTACT PLATE and BLADE OUTER CONTACT PATCH with zero ASSEMBLY MOUNTmG SCREWS and c learanc e . adjust CONTACT PLATE and I3LADE

\ ASSEMBLY until the requirement of Step C is met. Tighten CONTACT PLATE and BLADE ASSEMBLY MOUNTING SCRETVS .

CONTACT PLATE and - BLADE ASSEMBLY

COWACT BOARD and CABLE ASSEMBLY 1

- OUTERCONTACT I PATCHES

I

a 1 ' I

OUTERCONTACTBLADE

OVERRIDE ASSEMBLY ADJUSTMENTS

Ver i fy that Record Changer is in "Home" position, then position Line Switch to OFF . Remove Cover Plate from Override Assembly; position Line Switch to ON.

A . Verify that both escapements of RATCHET I3. Should adjustment be necessary, loosen WHEEL and HUB ASSEMBLY are OVERRIDE SWITCH ADJUSTTNG SCREWS cancelled off and OVERRIDE SWITCH and adjust OVERRIDE SWITCI-I as is open with .015 MINIMUM CLEAR- required to satisfy requirement of Step A . ANCE between switch contacts as shown. (Contact pressure t o be 15 Grams

\ measured at contacts . Blades may be reformed if necessasy . After adjustment is conipIeted, tighten OVERRIDE SWITCIi ADJUSTING SCREWS.

ADJUSTMENT SPACERS

RATCHET WHEEL and HUB ASSEMBLY

.015 MINDdUM CLEARANCE

OVE RRLD E SWITCH

OVERRIDE SWITCH ADJUSTING SCREWS

WURLITZER Page 5C

SECTION C

C . Ver i fy tha ta l lSELECTIONACCUM- I3. Position Service Switch t o OFF and U U T O R LATCH PINS are cancelled 01f . verify that SCAN-LOAD-RUN Switch

is in RUN position.

SOLENOD PLUNGER

ESCAPEMENTS

RATCHET WHEEL and HUB ASSEMBLY

E, Manual~ac tua teSOLENOLDPLUNGER P. Slowly rotate RECORD hSAGAZINE t o release the hvo ESCAPEMENTS of unti l Override Can1 on the Record RATCHET WHEEL and HUB ASSEMBLY Magazine Drive Arm passes Override as shown. Hub of t he Overr ide Assembly.

RATCHET WHEEL and HUB ASSEMBLY

ESCAFEMENTS

G . V e r e that one ESCAPEMENT on the H. Continue to slowly rotate RECORD RATCHET WHEEL and I iUB ASSEMBLY W G A Z I N E until Overr ide Cam an the cancels off as s h o w n . Record Magazine Drive Arm appxoac h e s

Override Hub on the Overr ide Assembly for the second rime (approachirlg "Home" position).

Page 6C WURLlTZER

- SECTION C

- I. Firmly grasp t h e RECORD MAGAZINE J . Vertfy that second ESCAPEMENT of and continue t o slowly rotate the RATCHET WHEEL and HUB ASSEMBLY RECORD MAGAZINE until Override is cancelled off as shown. - Cam on the Record Magazine Drive Arm passes the Override Hub on the Overridc Assembly. DO NOT release grasp on RECORD hlVIGAZZNE.

ADJUSTMENT SPACERS

RATCHET WHEEL and I-TUB ASSEMBLY

.015" MINIMUM CLEAKANCE

OVERRIDE SWTTCI-I

OVERRIDE SWITCH ADJUSTING SCREWS

K. V e r d y t h a t LOCKlNGPINofMAGAZINE L. Shourd adjustment be necessary, loosen LOCKING ARM engages p r o p e r escape- Override Assembly ADJUSTMENT ment of RECORD MAGAZLNE PLATE SPACERS and adjust Overr ide Assembly 1/4 OF ESCAPEMENT SLOPE LENGTFI to satisfy the requirement of Step K. from top of escapement as shewn. Tighten ADJUSTMENT SPACERS.

- 3 . \ L RECORD IVIAGAZINE . p 114 OF ESCAPEMEh!

2+ SLOPE LENGTI-I

,7--.- ---.:- -. -I b

-_ . /

' LOCKING PIN RECORD MAGAZLNE PLATE

I

I i

.A LOCKING ARM

M . Manually actuate SOLENOID PLUNGER N. Verify that RECORD MAGAZINE makes to: reIease both ESCAPEMENTS of the two complete r c v o l u ~ i o n s a n d s t o p s in

RATCXET WHEEL a n d I-IUB ASSEMBLY "Home" pos ition (RECORD TAKEOUT then position Service Switch to ON. ARM one escapement clockwise from

A-L record slot) .

WURLITZ ER Page 7C

SECTION C

MAGAZINE LOCK SWITCH ADJUSTMENT

A n VexifythatLOCKINGPINofMAGAZINE R , W i t h M G A Z W L O C K S W I T C H LOCKING ARM is ful ly engaged with actuated, clearance between MAGAZINE RECORD MAGAZINE PLATE as shown. LOCK SWITCH ACTUATOR and SWITCI-I

BODY should be 1/64",

RECORD MAGAZINE PLATE

MAGAZTNE LOCK SWITCH ACTUATOR

MAGAZINE LOCK SWITCH ADJUSTING SCREWS

a SWITCH BODY

LOCKING PIN

MAGAZINE LOCKING ARM

C . Should adjustment be necessary, loosen hMGAZINE LOCK SWITCH MOUNTING SCREWS and adjust MAGAZINE LOCK SWITCH as required ro satisfy requirement of Step B. Tighten MAGAZINE LOCK SWITCI-I MOUNTING SCREWS.

MAGAZLNE DRIVE MOTOR ADJUSTMENT

A. Position Service Switch to OFF. Select B. Manually rotate RECORD MAGAZINE any convenient: selection from SE LE C - two conzplete revolutions and check TOR SWLTCN, then manually cancel mesl~ing of MAGAZINE DRrVE GEAR LATCH PLN selected. and RECORD MAGAZINE GEAR.

RECORD MAGAZLNE

MAGAZThTE DRIVE MOTOR MOUNTING

GEAR SCREWS.

MAGAZINE DRIVE GEAR -

- r.42 7-.

C . Should adjustment be necessary, loosen M A G A Z W DRTVI3 MOTOR MOUNTING SCREWS and adjust motor as required t o satisfy requirements of Step 13. Tighten MAGAZINE DRIVE MOTOR MOUNTING SCREWS.

Page 8C WURLITZER

SECTION C

SIDE 1 CANCEL SOLENOID ADJUSTMENT

Prior to making the following adjustments, ver* that the RECORD hk4GAZmE is in "I-lame" position then position t h e Service Switch to OFF.

A . Manual lypos i t ion theRECORDMAGA- 8 . V ~ ~ ~ ~ ~ L ~ ~ ~ L O C K I N G P I N O ~ M A G A Z I N E AlNE so t h a t Selection A-L is centered LOCKING ARM is fully engaged with

directly beneath the RECORD TAKE OUT RECORD MAGAZINE PLATE escape - ARM. ment as shown.

LOCKThTG PIN RECORD MhGAZINE PLATE

MAGAZINE LOCICING ARM

SIDE 1 CANCEL S Q LE NOID PLUNGER

I: Fhl4 ' - -

I - , .- c*' ',

rv,' ' < I

., ._I-. '

READOUT ARM -,TAT h~ p :I' , *

LATCH BIN A-X

. .

READOUT ARM ADJUSTING SCREW

C . ManuslLl~r relcas e LATCH PIN A-1 . 13. Should adjustment be necessary, care- Verify that S D E 1 CANCEL SOLENOID fully t u r n READOUT ARM rlDJUSTlNG PLUNGER is centered + 01: - 1/64" over SCREW in o r out to satisly rhc require- LATCH PIN A -1 . ment of Step C . Return RECORD

MAGAZhVE to "Ho1ne"position.

WURLITZ ER Page 9C

- SECTION C

D'IGITAL RECORD NOW PLAYING INDICATOR ADJUSTMEh'T -

A . Verify that Record Changer is in "Home" 3. Verify t h a t Digital Indicator displays - pos ition. Select: L-1 . When selected selection L-1 and that OUTER BLADE record is in "Play" position, position of CONTACT PLATE and BLADE Service Switch OFF. ASSEMBLY is centered on L-1 PATCH -

of CONTACT BOARD and WIRE ASSEMBLY.

OUTER BLADE

CONTACT PIATE and BLADE ASSEMBLY

CONTACT PLATE and BLADE ASSEMBLY ADJUSTING SCJIEW

L-1 PATCH

CONTACT BOARD m d WIRE ASSEMBLY

C. Sheuldadjustmentbenecessary, adjust D. Positinn Service Switch to ON, cancel CONTACT PLATE a n d BLADE ASSEMBLY selected record and allow Record ADJUSTDlG SCREW as required to Changer t o r e t u r n t o "Home" position. satisfy the requirement of Step C,

STDE 1 and 2 READOUTSWITCH ADJUSTMENTS

A . VerifythatRecordChanger is in 'Nome" B . E s t ~ l i s h c r e d i t f o r r e c o r d s e l e c t i o n position and all LATCH PINS are then position Service Switch t o OFF. cancelled off.

C , Select: A-1 and A-2 (B-1 On Model D. Vcsify that MAGAZINE LOCK 3860). Manually cancel selected SOLENOID is activated. LATCt-I PINS.

E . T u r n SIDE 1 PRETRAVEL ADJUST- F . Turn SIDE 2 PRETRAVE i ADJUST- MENT SCREW in unti l MAGAZINE MENT SCREW in until MAGAZINE LOCK SOLENOLD deactivates. Back LOCK SOLE NOID deactivates . Back out'SLDE1PRETRAVELADJLTST- out SIDE 2 PRETRAVEL ADJUST- MENT SCREW u n t i l MAGAZINE M E W SCREW unt i l MAGAZINE LOCK LOCK SOLENOID activates plus one SOLENOID activates plus one addit ional full turn. additional fu l l turn.

Page 10C WURLITZER

SECTION C

SIDE 2 P R E T M V E L - ADJUSTMENT SCREW

- SIDE 1 PRETRAVEL AUJUSTFUIENT SCREW w: .-:: /I

I

-

- G . S e l e c t D - l a n d Q - 2 ( 2 - 2 a n d M - Z o n W. Manually rotate RECORD MAGAZLNE

~ d d e 1 3 860). Pos ition Line Switch t o position READOUT SWITCH

- t o OFF. ACTUATORS close to, but not touching, selected LATCH PINS.

SIDE 2 READOUT SWITCH ACTUATOR

SIDE 1 READOUT SWITCH ACTUATOR

LATCH PINS

I. Bottom edge of ACTUATORS should be J . Ends of ACTUATORS should overlap 7

1/16" TO 3/32" below top of selected edge selected LATCH PINS 1/32" LATCH PINS. to I J l f" .

- NOTE : Should adjustment be necessary to satisfy requirements of Steps 1 and 5, ACTUATORS may be reformed.

- K . Manually rotate RECORD MAGAZINE L. Position Line Switch to ON and Select A-1.

t o "Home" position and manually cancel - selected LATCH PINS .

M. Observe LOCKING PIN and slowly N . Release RECORD MAGAZINE and ver@ - rotate RECORD MAGAZINE u n t i l that RECORD W G A Z I N E is in position

SIDE 1 READOUT SWITCH actuates, t o play selection A- l . seleas ing LOCKING PTN which sl~oulcl strike escapement: of RECORD h U G A - ZTNE PLATE at 1/4 of ESCAPEMENT SLOPE LENGTH h o r n top of escape-

- ment as shown.

WURLITZER Page 1IC

SECTION C

MAGAZINE - PLATE

1/4 OF ESCAPEMENT SLOPE LENGTH

--\\ - \ LOCKING PIN

"!: . , - \ - k . . . . I

, - LOCKING ARM

I

0. Should adjustment be necessary, a d j u s t P , Repeat Steps K through 0 t o verify SIDE 1 READOUT SWITCH ADJUSTING proper operation of SIDE 1 READOUT SCREW as required to satisfy require- SWITCH. ments of Steps M and N . Turn ADJUST- ING SCREW in t o retard switch actuation a and n u t to advance switch actuation.

SIDE 2 READOUT SWITCH ADJUSTING SCREW

SLDE 2 READOUT SWITCH ACTUATOR

SIDE 1 READOUT SIDE 1 READOUT SWITCH ADJUSTING SWITCH ACTUATOR SCREW -

$' - - ,- - - - % 44- -rzzr7=?!!!FnLL -

Q . Manually rotate RECORD MAGAZINE R . Pos ition Line Switch to OFF then ON to "Home" position and manually and select: A-2 (B-1 on Model 3860). cancel selected LATCH PTN .

S . Obs e r v ~ LOCKING PIN and slowly T. Release RECORD MAGAZZNE and rotate RECORD MAGAZINE until verify that RECORD MAGAZINE is in SIDE 2 READOUT SWITCH actuates, position to phy selection A-2 releasing LOCKING PIN which should (0-1 on MadeL 3860). strike escapement of RECORD MAGA- ZINE PLATE at 114 OF ESCAPEMENT SLOPE LENGTH from top of escapement.

Page 12C WURLITZER

U . Shoulcl acljustrneilt IJC t~eccssary, acljust: SIDE 2 RErlnOUT SI!lITCI-I _\DJUSTISG SC:RE\ZT as rec~ui rcd tr , siltisry rccl~i i r e - ments oi S t e l ~ s S :~ncl T. T u r n ADJLTST- TNG S C ' R E ~ ~ J in to rotard swi t ch nctu - ation r ~ n t l nut' to arlvanc L. switcla ac~ut l t io l l

I41 . Check posi t ion 01 SIDE 1 and SIDE 2 R EADOI ,'T S W ITCI I AC'T"Ui1'rOltS . AC'TUATORS m u s t not cntuo to rest

ovc f 3 LATCI-I PIS \:.

r i . Wit11 Recrlrrl L'liat~ger in "I lonle'" 13 . pus itinn, ~nanually bottr SAFETY S WITC'T-I ACTUATOR ag;l i nsc sw itch hotly , Tlierc! shrjulrl 1x2 1 /:l'l" CI LEAR- r\NCE behvecn SA t; ETY SWITCH ACTU:'ITOI'C ancl C: LAMI' \'IS .

ItECORD CLAMP PIN

SAFETY S W ITCIT 1 ADJUSTMENT PLATE

SAFET1' SWTTCII-I ACTUATOR

S . Sl~uu ld a d j u s t c ~ l c ~ ~ t bc noc essar-y, t~lrn a ~ ~ p n q ~ ~ - i a t o PRETRAT'EL AIIJLTSTZ\IENT SCRE\Y s lnwly c o ~ l n ~ u r c loc kivisp u111:il

rhe recluiremen'c oT Stcp \V . is satisfied.

Sli ould acljuscment IILI tieuossary, Innsen SAl:ETIp S\!/ITi:I-I AWESTIKG SC'lZI'\YS anxl adjust S A F E m SIVITCI-1 as rccluirerl t r l satisfy ~:equ ircmcnt of Stup A .

a TighCcn SIZF ETY SWITCH .'lTlJUSTIN(.: SC'IiEWS.

SAFETY SWTTCI-I ADJUSTMENT PIATli

SAFETY SWITCT-I

J, , { :,.; Q\ I

I I ,,/:. ,.: I .'. f : , ',.;:" -- .!; :---\: :, -.~:

r > ~ . ., , ,-- ?., i! . , : . - . -----

..xL:. ... -

SECTION C

BAIL AND BUSHING ASSEhrLDlY CLEARANCE ADJUSTMENT

A , With RECORD TAKEOUT ARM in "Horne" l3. Should adjustment be necessary, loosea position, there should be .OIO1"END ALLEN SCREWS on either s i d e of BAIL PLAY between BAIL and BUSHING a ~ ~ d RUSI-IING ASSEMBLY and adjust ASSEMBLY and GEAR PLATE and loosened s ide to satisfy requirement PIN ASSEMBLIES . of Step A . Tighten ALLEN SCREWS.

-010'' END PLAY

BAIL and BUSHING ASSEMBLY

I < I

I GEAR PLATE and -b I- PIN ASSEMBLY - ' ' ALLEN SCREWS

:?3/ -i

.--. -

GEAR PLATE and I-.' -- ----[A

. r- F

PIN ASSEMBLY '--_ d

I rn i ~ l

MAIN CAM MOTOR BRAKE ADJUSTMENT

Prior t o making the following adjus tment , verify that: Record Changer is in "I-lome" position, then position Service Switch to OFF.

I

I A . Manually actuatc MAIN CAM MOTOR B , Should adjustment: be necessary, loosen BMKE SOLENOID FLUNG E R . Tllere SOLENOZ13 MOUNTING SCREWS, then

should be 1/32" t o 3/64" CLEARANCE while manually actuating U I N CAM between LEVER and PAD ASSEMBW MOTOR BRAKE SOLENOYD PLUNGER, and BRAKE WHEEL. a d j u s t MAIN CAM MOTOR BRAKE

SOLENOID as required t o satisfy requ irernent of Step A . Tighten SOLENOID MOUNTING SCREWS.

BRAKE W E E L

1/32" t o 3/64" CLEARANCE

LEVER and PAD ASSEMBLY

MAIN CAM MOTOR BRAKE SOLENOID

MIN CAM MOTOR BRAKE SOLENOID PLUNGER

SOLENOID MOUNTING SCREWS

Page I4C WURLITZER

SECTTON C

Ver i Iy t11t~C a record is in "Play" pos i r i o ~ i . Cancel record ancl i r n i ~ ~ e d i a t e l y upon rclcr~~:cl entering IIECORD MAGAZIME, position Service S w i ~ u h to OFF.

A. l'osition Serv i cc Switch to ON and cycle rv -7- CAM and GEAR ASSEMBLY ~ l ~ l t i l -? t RECORD CLAMP CAM FOLLOWER reaches the peak of RECORD CLAMP RECURD CLAMP CAM LOBE as shown, Ellen posir inn CAM ITOLLOWER Service Switch to OFF.

RECORD CLAMP 1 : lGbn1r~, 1 CAM L.OBE

I I

/ ( I

.j - 6 - e 6 -. -'*--- - ' !. - -

B . Mantlally position TRANSFER SWITCT-I C . S l ~ o ~ ~ l c l adjustment be necessary, loosen ACTUATOR as s h o w n . Tilere should TRANS F E 11 S WITCI-I MOUNTING bc 1/16'' CLEARANCE between t i p of SCREWS ancl adjust: TRANSFER SWITCH TRANSFER SWITCH ACTUATOR and 3s required to satisfy requirement of MAIN GEAR T F U C K LOBE. Stcp U. Tighten TRANSFER SWITCH

MOUNTING SCREWS.

TRANSFER SIVITCH MOUNTING SCREWS

TRAKSFER SWITCI? ACTUATOR

1/16" CLEARANCE

- MAIN GEAR TRACK LOBE

WLTRLITZER Page 15C

- SECTION C

- D . Pas ition Service Switch t o ON and cycle E . Manually bottom T M N S F E R SWITCH

CAM ancl GEAR ASSEMBLY untiL ACTUATOR against s w i t d ~ body. Thel-c TRANSFER SWITCH ACTUATOR is should be 1/32" CLEARANCE between

TRANSFER SWITCI-I ACTUATOR a n d -

r id ing on MAIN GEAR TRACK as shown, t h e n position Service Switch tb OFF. MAIN GEAR TRACK.

TRANSFER SWITCH MOUNTING SCREWS TRANSFER SWITCH

ACTUATOR

- 1/32" CLEARANCE

MAIN GEAR TRACK

F. ShouldadjustmentIsenecessary, loosen C . Position Service Switch to ON and cycle TRANSFER SWITCH MOUNTING SCREWS, CAM and GEAR ASSEMI3LY . Verify making sure that horizontal pus irioni n g is that each time TRANSFER SWITCFI maintained, then adjus t TRANSFER ACTUATOR falls into recess of MAIN SWITCH as requisecl t o satisfy requircrnent GEAR TRACK, switclr actuates . of Step E. Tighten TRANSPERSiVITCH MOUNTING SCREWS.

C A K E L SWITCI-I ADJUSTMENT

Prior tn making the fallawing acTjustrnent, position SERVICE SWITCFI t o OFF and verify that SCAN-LOAD-RUN SWITCI-I is in RUN position. Makc a record selection.

A . Utilizing Service Switch, cycle CAM B, Should adjustment be necessary, loosen and GEAR ASSEMBLY u n t i l CANCEL CANCEL SWITCH MOUNTING SCRElVS SWTTCT-I ACTUATOR is on peak of and adjust CANCEL SWITCH as required cam lobe as shown. Verify that to satisfy the r e q u i r e m e ~ ~ t of Step A . CANCEL SWITCH has actunted with Tighten CANCEL SWITCH MOUNTING 1/32 " t o 3/64" overtravel. SCREWS.

CAM LODE

CANCEL SWlTCl-1 ACTUATOR

CANCEL SWITCH

CANCEL SWITCH ADJUSTLNG SCREWS

Page 16C

SECTION C

RECORD TAKEOUT ARM ALIGNMENT

A . Select a record that is known to be flat, K. Shorrlcl adjustment be necessary, loosen Utilizing Service Switch, stop RECORD LOCK NUT and adjust RECORD TAKE- TAKEOUT ARM w h e n STOP PINS d OUT ARM ADJUSTMENT SCREW as

GEAR and PLATE ASSEMBLIES are required to satisfy requirement of approximately 1/16" to 3/16" from Step A . Tighten LOCK NUT. RECORD TURN STOP ASSEMDLIES. Verify that record is centered between "V1'pportion of RECORD SEPAKATORS as shown.

RECORD SEPARATORS

RECORD TAKEOUT ARIA4

RECORD TAKEOUT ARM ADJUSTMENT SCREW

SIDE L RECORD TURN ARM

STOP PINS

STDE 2 RECORD TURN ARM

LOCK NUT

Versfy that selected record is ceutercd D . Should adjustment be necessary, loosen between RECORD GUIDE TIPS as sllow11. RECORD GUIDE MOUNTING SCREWS

and adjust- RECORD GUIDE as necessary t o satisfy requirement of Step C . Tighten

RECORD GUIDE TIPS RECORD GUIDE MOUNTLhTG SCREWS.

RECORD GUIDE MOUNTING SCREWS

RECORD GUIDE

W R L I T Z E R Page 17C

SECTION C

PLAYMETER RESET MAGNET ADJUSTMENT 1 J16" CLEARANCE

7- I - - A . Depress PLAYMETER RESET MAGNET

and verify tha t there is 1/16'' CLEAR- ANCE between PLAYMETER RESET 4- - PLAYMETER MAGNET and PLAYMETER RESET I , RESET MAGNET LEVER, t* >-L. / Q-* -,. , .?*

1. '6 .

R . Should adjustment be necessary, loosen ' MAGNET ARM MOUNTING SCREWS bJ / and adjust PLAYMETER RESET

MOUhTmG SCREWS.

t MAGNET as required to satisfy require- 3 > %>

ln cut of Step A . Tighten MAGNET ARM 1.9 '\

- PLAYMETER RESET LEVER

' MAGNET A m 8 : ,I-:. \ i

t w MAGNET ARM MOUNTING

C

SIDE 1 SHIFT ADJUSTMENTS

SCREWS

A . Position Service Switch to OFF then B. F l a n g e o f S I D E l R E C O R D T U R N A R M select: A-1 . Position Service Switcll sliould be centered between inner side t o ON then to OFF to stop Record of head of STOP PIN and side 01 RAIL Changer when STOP FINS of GEAR and CASTING as shm n . PLATE ASSEMBLIES are 1/4" from RECORD TURN ARMS as shown.

STOP PIN

1/4" CLEARANCE

SIDE 1 RECORD TURN ARM

GEAR and PJXTE ASSEMBLLES

STOP PIN

SIDE 2 RECORD T U R N ARM

C . Should adjustment be nEessary, loosen D. Position Service Switch to ON, cancel SOLENOID ADTUSTING SCREWS and selected record, then posit ion Service adjust energized SIDE 1 SHIFT SOL- Switch to OFF. E N O D as necessary to satisfy require- ment of Step R. Tighten SOLENQZD ADJUSTING SCREWS.

Page 1 SC WURLITZE R

SECTION C

. .

< >

SIbE L SHIFT SOLENOD

C.)

SIDE 1 SOLENOID SOLENOID SWITCHES ADJUSTING SCREWS

,. F

- ,< .

E. VerifythatSDElSOLENOIDSWTTCHES F. Shouldadjustmell l :benecessaq, loosen are actuated wi th 1/32" overtravel. SWITCH MOUNTTNG SCREWS and

adjust as necessary to satisfy xequire- ments of Step D . Tighten SWITCH MOUNTING SCREWS.

G . Select A-2 (B-1 on Model 3660). Position I-!. There should be 5/64" to 7/64" Service Switch t e ON then to OFF t o C LEAMNCE between head of STOP stop Record Changer when STOP PINS PIN and SIDE 1 RECORD TURN ARM of GEAR and PLATE ASSEMBLIES are as shown. 1/4" from RECORD TURN ARMS as shown.

STOP PIN GEAR and PLATE ASSEMBLIES

SIDE 1 SOLENOID ADJUSTING SCREW

SIDE 1 RECORD TURN ARM

5/64" TO 7/64" 1 CLEARANCE

I . Should adjustment be necessary, adjust J , Pos i t i onSe rv i ceSwi t ch toONthe~ l SIDE 1 SOLENODJ STOP ADJUSTING cancel selected record. SCREW as necessary to satisfy requixe- ment of Step H,

WURLTTZER Page L9C

SECTION C

TURN ARM HOLDOUT CAM ADJUSTMENT

A . W i ih Record Changer in %ornew pos ition, I3 . Should adjustment be necessary, loosen flat surface of LOCKOUT CAM should be SET SCREWS and ad jus t LOCKOUT vertical to RECORD CHANGER MOUNTING CAM as required to satisfy requirement PLATE as shown. af Step A . Tighten SET SCP FWS .

LOCKOUT CAM \

RECORD CHANGER - MOUNTING PLATE

e

I

SET SCREWS 1

C . Loosen SET SCREW located on top of D . Should adjustment be necessary, loosen LOCKOUT CAM. Select A-3 (C-1 on remaining SET SCREW and adjust Model 3860). Position Service Switch LOCKOUT CAM as required t o satisfy t o OFF as RECORD TAKEOUT ARM requirement of Step C . Tighten SET starts to t u r n . LOCKOUT CAM shouId SCREW. When Record Changer re turns make contact with SIDE 1 TURN ARM t o "Home'>osition, repeat Steps A and B. as shown.

I

%'-&FfiIi

LOCKOUT -

CAM - - i /I

SIDE I RECORD I TURN ARM

< RECORD TAKE OUT - - I ARM

Page 20C WURLITZER

SECTION C

RECORD TAKEOUT ARM STOP ADJUSTMENT

Make the following adjustment with the Record Changer in "Home" pos it ion,

A . Position a straight edge on TURN- B. Adjust RECORD TAKEOUT ARM TABLE as shown. There should be STOP ADJUSTMENT SCREW as required 1/8'"0 5 J32" CLEARANCE between t o satisfy requirement of Step A . straight edge and head of RECORD TAKEOUT ARM STOP ADJUSTMENT SCREW.

1/8" TO 5/32" -- CLEARANCE

TURNTABLE

RECORDTAKEOUT ARM STOP ADJUSTMENT SCREW

RECORD TAKEOUT ARM TURN A D J U S T m W

A . Select A-2 (B-1 on Model 3860). Position 3. Surface of TURNTABLE t o be 1/32 " Service Switch to OFF when selected TO 1/16'%elow V of RECORD TAKE - record is in "Playt' position. Remove OUT ARM ROLLERS. record from TURNTABLE.

RECORD TAKEOUT ARM ROLLERS

TURNTABLE L J32" TO 1/16'' BELOW V OF RECORD TAKEOUT ARM ROLLERS

WURLITZER Page 21C

SECTION C

C . Should adjustment be necessary, adjust D. PlacerecordbackonTURNTABLE. SIDE 2 RECORD TURN ARM ADJUST- Pos iticrn Service Switch to ON and MENT SCREW as required t o satisfy cancel selected record . requirement of Step B.

\ SIDE 1 RECORD SIDE 2 RECORD TURNARM TURNARM ADJUSTING ADJUSTING SCREW SCREW

. .

Select A-3 (C -1 on Model 3860). Position Service Switch t o OFF when selected record is in "Play" position. Remove selected record from TURNTABLE and xepeat Steps 3, C and D using SIDE 1 RECORD TURN ARM ADJUSTMENT SCREW.

rn TURNTABLE DRIVE WHEEL ADJUSTMEm

Far the following adjustment Record Changer must be in "Home" position.

A . Ver~fythatclearancebetweenTURN- B. ShouIdadjus tmentbenecessary , foosen TABLE DRIVE WHEEL and the 45 RPM the TURNTABLE ADJUSTMENT PLATE portinn of the TURNTABLE MOTOR MOUNTING SCREWS and adjust t h e SLEEVE is 1/64" to 1/32" as shown. TURNTABLE ADJUSTMENT PLATE as

required to satisfy the requirement p-==- TURNTABLE of Step A . Tighten TURNTABLE

ADJUSTMENT ADJUSTMENT PLATE MOUNTING

1 : PLATE SCREWS. I '

1/64" TO 1/32" CLEARANCE

TURNTABLE MOTOR SLEEVE

TURNTABLE ADJUSTMENT PLATE MOUNTING SCREWS

TURNTABLE DRIVE WHEEL

Page 22C WURLITZER

SECTION C

TURNTABLE SPEED CHANGE ADJUSTMENTS

A . S e l e c t a 3 3 1 / 3 R . P . M . r e c o r d . As B. Should adjustment be necessary, loosen record is positioned on TURNTABLE, TURNTABLE SI%ED CI-LANGE SWITCH TURNTABLfi SPEED CHANGE SWITCH MOUNTING SCREWS and adjust TURN- should actuate with 1 J32" t o 1/16" TABLE SPEED CHANGE SWITCH as ovestxavel of ACTUATOR. xequired t o satisfy reqclu irerncnt of

Step A . Tighten TURNTABLE SPEED CT-IANGE SWITCH MOUNTING SCREWS.

TURNTABLE SPEED CHANGE SWITCFI

TURNTABLE SPEED CHANGE SWITCH MOUNTING SCREWS

C . Manually actuate TURNTABLE SPEED D. TURNTABLE DRIVE WEEEL should CHANGE SOLENOID PLUNGER. Yi£t 1/4" .

\ TURNTABLE TURNTABLE SPEED CHANGE SOLENOID

TURNTABLE SPEED CHANGE SOLENOID PLUNGER

TURNTABLE D W E WHEEL

WURLITZ E R Page 23C

SECTION C

E , Should adjustment be necessary, cancel F . Verify tllar TURNTABLE PILOT is still record ahd manually co lhpse TURN- in 33 1/3 R. P.M. position. Reinstall TABLE PILOT t o 33 1J3"R.P.M. position. TURNTABLE, TURNTABLE RlNG and Remove TURNTABLE MOUNTING TURNTABLE MOUNTING SCREWS. SCREWS, TURNTABLE RING ancl Tighten TURNTABLE MOUhTING TURNTABLE. Loosen TURNTABLE SCREWS and verdy proper operation SPEED CHANGE SOLENOID MOUNTING of TURNTABLE PI LOT. SCREWS and ad just TURNTABLE SPEED CHANGE SOLENOID as required to satisfy

TURNTABLE PILOT

requirement of Step D. Tighten TURN- TABLE SPEED CHANGE SOLENOID [P * MOUNTING SCREWS. I I-

f! ' d - n t j !! .,*

TURNTABLE SPEED CHANGE :-. I .h

SOLENOID MOUNTING SCREWS 3. IF-

TONJZ ARM LIFT ADJUSTMENT

A. Position Service Switch to O F F . B. Position Service Switch to ON. When Select A-1 . TONE ARM is directly over RECORD

TAKE OUT ARM, pos it ion Servic e to OFF.

I" CLEARANCE \ TONE

/ ARM

RECORDTAKEOUT - ARM

Page 24C WURLITZEX

SECTTON C

C . ~eresh~uldhel"CLEARANCEbe~een D. Sliouldadjustmentbenecessary,adjust TONE ARM and RECORD TAKEOUT TONE ARM LIFT ADJUSTING SCREW ARM as shown. as required to satisfy requirement

of Step C .

I - TONE ARM TUBE

TONE ARM LIFT ADJUSTING SCREW' -

E. Position Service Switch t o ON and cancel selected record .

STYLUS BRUSH AQUSTMEhT

A . Position Service Switch to OFF. B . Position Service Switch t a ON, When Select: A-2 . TONE ARM is directly over STYLUS

BRUSH, posit ion Service Switch to OFF.

w STYLUS 6

\ - S,3LYESRBRUSH <p, - . .- II!

1 J 6 4 ' T O 1/32" c

PENETRATION p ,' 7

S P L U S BRUSH 4

!T HOLDER

STYLUS BRUSH :mi:3-:.- : >WU7 -5;-

MOUNTING SCREW

- I-.. -. - - _ - - L

C . STYLUS should contacr STYLUS D . Should adjusrment be necessary, loosen BRUSH with 1/64" t o 1/32" STYLUS BRUSH HOLDER MOUNTING PENETRATION. SCREW and adjust STYLUS BRUSH

I-TOLDER as required t o satisfy requirement of Step C . Tighten STYLUS BRUSH I-IOLDER MOUNTING SCREW.

WURLZTZER Page 25C

SECTION C

TONE ARM RELEASE ADJUSTMENTS

A . Make a record selection. Position B. There should be ZERO CLEARANCE Service Switch tn OFF t o stop (no play) between ADJUSTMENT Record Changer when TONE ARM LEVER and BUSHING ASSEMBLY, has started down on record, but prior LEVER and BUSHING ASSEMBLY, to TONE ARM touching rec ard . and PITOT ARM and PIN ASSEMBLY.

TONE ARM - LEVER and BUSHING ASSEMBLY

TONE ARM RELEASE ADJUSTING SCREW

ADJUSTMENT LEVER and BUSHING ASSEMBLY

ZEROCLEARANCE

PIVOT ARM and PIN ASSEMBLY

C . There should be ZERO CLEARANCE D. Should adjustment be necessary, adjust between ADJUSTMENT LEVER and TONE ARM RE LEASE ADJUSTING BUSHING ASSEMBLY and TONE ARM SCREW as required to satisfy require- RELEASE ADJUSTLNG SCREW. rnents af Steps B and C .

TONE ARM FEED-TN and TRIP SWITCH ADJUSTMENTS

A , Make a record selection. Position B . Should adjustment be necessary, loosen Service Switch to OFF to stop Record TONE ARM LOCKING SCREW and ad jus t Changes when TONE ARM has started TONE ARM FEED -IN ADJUSTING down an record, but prior t e TONE SCREW as required to satisfy the ARM touching record . TONE ARM requirement af Step A . Tighten TONE STYLUS should be 3 11/32'"ram tip ARM LOCKING SCREW. of NRNTAB LE PILOT,

2 3/321 DIMENSION

TONE ARM

3 11/32'' DIMENSION

TONE ARM STYLUS

Page 26C WURLITZER

SECTION C

C . Position Service Switch to ON to play D. Should adjustment be necessary, adjus t record. TRIPSWITCH should actuate TRIP SWITCI-J ADJUSTING SCREW as when TONE ARM STYLUS is 2 3/32" required to satisfy requirement of from t i p of TURNTABLE PILOT. Step C ,

3,, TRIP SWITCH - , T R P SWITCH ADJUSTING PLATE

I'. I- 9 \ - .

. \ , , 0 "

. - - L

0 ADJUSTING PLATE ADJUSTING SCREW

!

ADJUSTING SCREW

-- TONE ARM FEED-IN ADJUSTING SCREW

- TONE ARM LOCKING SCREW

E. With Record Changer in ttIiomet' 1;. Should adjustment be necessary, loosen position, manually actuate TRIP ADJUSTING PLATE ADJUSTING SWZTCFI ACTUATOR. Slowly release SCREW and adjust: TRIP SWITCH 9 ACTUATOR. When TRIP SWITCH ADJUSTING PLATE as required t o resets, ACTUATOR should be 3/32 " satisfy the requirements of Step E . to l / B 1 ' from TRIP SWITCH ADJUST- ING PLATE.

PLAY SWITCI-I ADJUSTMENT

A. SelectA-l . PositionServiceSwitch l3 . Verify that PLAY SWITCH actuates t o OFF when selection is in "Pby" with avertravel. The SWITCH pas ition. ACTUATOR must not bottom on

SWITCH BODY.

w , 7 - F / jr/. ""\,: I 's: PLAY S W T C H

1/32" of A-

4' - MOUNTING SCREWS

CAM LOBE - \ k-

CAM LOBE 0' P"1

PLAY SWITCH ACTUATOR

C SET SCREWS

C . Should adjustment: be necessary, Ioosen D. Loosen SET SCREWS and position PLAY SWITCH MOUNTING SCREWS CAM LOBE as shown. Tighten and adjust PLAY SWITCH as required S E T SCREWS. to satisfy the requirement of Step R . Tighten PLAY SWTTCI-I MOUNTING E . Pos ition Service Switch t o ON and SCREWS. cancel selected r e c o r d .

WURLITZER Page 27C

SECTION C

STYLUS PRESSURE ADJUSTMENT

A . Wtth a record on t h e turntable and 13. Stylus should break contact with record TONE ARM in playing position, apply ar 5 to 7 Grams of upward pressure as STYLUS GAUGE 3 / 8 " h m mend of indicated on STYLUS GAUGE. Should TONE ARM as shown. adj~rsurnent be required, proceed to

Step C .

STYLUS GAUGE

C . To ad jus t STYLUS pressure, loosen STOP NUTS and adjust STY LUS PRESSUXE ADJUSTMENT W E IGI-ITS as required to satisfy the requirement

STYLUS PRESSURE ADJUSTMENT

of Step 0 . Tighten STOP hWTS . STOP NUT WEIGHTS

S T O P N U T -

Page 28C WURLITZ ER

SECTION C

TURNTABLE PILOT RESET ADJUSTMENT

A . Make a selection. Using Service Switch, B. There should be 1 J 3 2 " to 3/64" CLEAR- stop Record Changer when TURNTABLE ANCE between PILOT LATCH LEVERS PILOT has been lifted t o maximum height and TURNTABLE RING as shown.

TURNTABLE RING / 1/32" to 3/64"

CLEARANCE

A' TUWMLE PILOT LEVERS

TURNTABLE

C . Shouldadjustrnentbenecessary,adjust D. Position~er&ce~wiichfo'ON, then TURNTABLE PILOT LIFT ADJUSTING select a 33 1/3 R.P.M. record. With SCREW as required t o satisfy require- selected record in "Pkjr" position, ment of Step B. verify that there'is VISUAL CLEAR-

ance between TURNTABLE RESET LEVER and I-IUB ASSEMBLY and

TURNTABLE RESET LEVER PILOT TUBE WASHER. and HU5 ASSEMBLY

\ I I '.

-11 1 PILOT TUBE WASHER - I '.

7 I

1

VISUAL CLEARANCE

TURNTABLE PILOT LIFT ADJUSTING SCREW

SECTION C

INDEX T O PARTS DRAWINGS

Record Magazine Assembly

Selection Accumulator

Record Changer L.H.

Cam and Gear Assembly

Record Changer R .H.

Turntable and Mounting Plate Assembly

Tone Arm Assembly

Record Takeout Arm

Turntable Assembly

Page 30C

- Page 31

Page 32 -33 -

Page 34-35

Page 36-37 - Page 38-39

Page 40-41 -

Page 42

Page 43 -

Page 44

- WURLITZER

SECTION C

I . Label, Record Playing - 2 . Label, Record Playing (Numbers 2 through 8)

3 . Label, Record Playing - (Le t t e r s C through K) 4 . Label, Record Playing

(Number 1 ) Label, Record PI aying

7

(Le t t e r s A and B) Label, Record Playing

(Le t t e r s F and G ) - 5 . Label, Record Magazine Loading

6 . Label, Record Magazine

- Loading

RECORD MAGAZINE ASSEMBLY

3800 136770 7 . Record Separa to r Assembly 135982

8 . Casting, Record Holder 136521 3860 136771 9 . Plate and G e a r Assembly 135958

1 0 . F i l l e r , Record Magazine 3800-3860 136513 3810 136773 F i l l e r , Record Magazine 3860 136514

Support Assembly, 3860 136772 Magazine F i l l e r 3860 138824

Mounting Bracket 3810 136774 Assembly 3860 136516

Fil ler ,Record Magazine(2) 3810 136515 3810 136775 Support Assembly,

Magazine F i l l e r (2 ) 3810 138823 3800-3810 134714 Mounting Bracket

Assembly (2) 3810 136516 3860 134873 11. Record Separa tor and Counter Assembly 135979

WURLITZER Page 31C

SECTION C

SELECTION ACCUMULATOR ILLUSTRATED PARTS LIST

1 . Latch Pin, Inside 128321 , 2 . Latch Pin, Outside 128320 -

Spring, Latch Pin, Selection Accumulator 128322

3 . Ring and Spacer Assembly 3800 133532 Ring and Spacer Assembly 3860 134245 Ring and Spacer Assembly 3810 134082 Spacer (8) 128324

4 . Plate, Pin Stop 133348 5 . Shaft and Magnet Arm Assembly,

Selection Accumulator 133499 6 . Bobbin and Wire Assembly (2) 133375 7 . Shield and Support Assembly 138786 8 . Contact Plate and Blade Assembly (2) 138299 9 . Thrust Washer (2) 122630

10. Ball Race 122631 11. Spacer, Selection Accumulator (8) 133886 12. Contact Board and Cable Assembly 3800 138286

Contact Board and Cable Assembly 3860 138287-

Contact Board and Cable Assembly 3810 138288

Plug, 12 131176 Pin Terminal (9) 132000 Receptacle, 15 131888-

Contact Terminal (15) 132001 Receptacle, 9 131173

Contact Terminal (9) 132001 Receptacle, 12 131175

Contact Terminal ( lo ) 132001 13 . Casting and Bearing Assembly,

Selection Accumulator 133531 Clutch Bearing 128638

14 . Screw, 1/4-20 x 3/4, Cap (3) 73571 -64 Lockwasher (3) 73605-9 --

15. Spring Washer 128739 16 . Gear and Hub Assembly,

Selection Accumulator, Shaft 128305 +.

Set Screw, 8/32 x 3/16 73528-29 T 17. Motor Mounting Plate, - Selection Accumulator 128291 18. Motor and Gear Assembly 135136

Gear and Hub Assembly 128293- - Roll Pin 73782-34 19. Support Leg, Selection Accumulator 133420

(For Service Only) - 20. Mounting Bracket, Receptacles 138296 21. Capacitor, .18 mfd . 75V (2) 76201-17 .̂

22. Diode, Zenner (2) 128449 .- - WURLITZER Page 33C

SECTION C

WURLITZER

SECTION C

RECORD CHANGER ILLUSTRATED PARTS LIST, L .H.

1. Record Support 136491 Contact Te rmina l (15) 132001 2 . Cam, Override 135922 Receptacle, 15W 131888- 3 . Drive Arm and Contact Blade Assembly 137318 Contact Te rmina l (10) 132001

(Part of Drive A r m and Support Receptacle, 6 138838 A r m Assembly, 137333) Contact Terminal ( 3 ) 132001 Roll Pin 73782-52 Plug, 6 131172

4 . Housing and Clutch Assembly 128643 Pin Terminal (5) 132000 Roller Clutch 128641* 34 . Cancel Solenoid Assembly 133476 - Housing and Bushing Assembly 128384 Internal Ha i r Pin (2) 77402-1 Bushing 128383- Cup Washer (2) 64766

5 . Guide, Ratchet 128367 Spring (2) 64780 - Spacer (2) 135185 Plunger (2) 133374

6 . Switch and Bracket Assembly 135959 35. Spring, Readout Switch (2) 133426, Switch Assembly 138837 36. Switch and Actuator Lever Assembly, Retainer Plate 63014 Side 2 135803 Mounting Bracket 135924 3 7 . Pre t ravr l Bracket and Stop Nut Assembly 135499

7 . Ratchet Wheel and Hub Assembly 128363 (2) 8 . Spacer Stud (2) 135938- 3 8 . Bracket Assembly, Readout(2) 133475 9 . Cover, Override 136458 3 9 . Switch and Actuator Lever Assembly,

10. Solenoid 133482 Side 1 135802 Gripring 76922-12 40. Support A r m and Stop Nut Assembly 137315

11. Spring, Lever and Link 136154 (Par t of Drive A r m and Support 1 2 . Latch and Pin Assembly 135969 A r m Assembly, 137333) 1 3 . Spring, Armature 136236 Roll Pin 73782-51 1 4 . Spring, Ratchet Wheel 128647 - Retaining Ring 73724-39 15 . Mounting Plate and Stud Assembly 135964 Spring (2) 137330 -

Spacer, Override 135937 41. Spring 133418 16 . Lever Assembly, Override 135967 42. Arm, Readout 133535

Retaining Ring 73724-15 43. Shaft, Drive A r m 135929 17 . Spring 133543 (Par t of Drive A r m and Support 18. Counter, Lever and Hub Assembly 138027 A r m Assembly, 137333)

Bracket and Pin Assembly 138024 44. Bracket, Contact Plate 136039 19 . Window Plate and Rivet Assembly 134592 Resis tor 175 ohm, 5W (2) 74824-2 20. Plate and Silk Screen Assembly 141118 45. Contact Plate and Blade Assembly, Dlx. 136438 21. Mi r ro r , Record Playing 141111 Contact Plate and Blade Assembly,Std. 136472 22. Lamp, No. 1847 138275- 46. Mounting Bracket and Pin Assembly 142883 23. Light Socket and Wire Assembly 110454 47. Locking A r m and Link Assembly 136431

Receptacle (6) 138838 Spacer 129818 Contact Terminal 132001 Stop Nut 4-40 74988-7

24. Light Bracket, Record Playing 136466 48. Spring 128748 25. Spacer, Record Playing Plate 137026 49. Switch 128344- 26. Magnet and F r a m e Assembly 135771 Tapping Plate 128283

Resistor, 135 ohm, 5 Watt 74840-2 50. Solenoid and Plug Assembly 142879 27. Mounting Bracket, Window Plate 136462 Mounting Plate, Solenoid 142884 28. Mounting Plate and Spacer Assembly 134003 5 1 . Channel and Spring Assembly 29. Motor and Gear Assembly 133487 Left Hand 140393

Receptacle, 2 129381 Spring 140805 Pin Termina l (2) I32000 Retaining R l i l (not shown) 140668

30. Spacer, Selection Accumulator 133402 52 . Retainer, Chass is Spring (2), 31. Mounting Bracket and Roller Assembly(4) 135707 Part of Item 51. 136506 32. Positioning Plate, Magazine Lock 135212 53. Spring (2), Part of I tem 51. 61059 33. Contact Board and Wire Assembly, Std. 138878 54 . Retainer, Chass is Spring (2),

Plug, 6 131172 Part of Item 51 . 1 3 4 7 3 5 4 Pin Termina l (5) 132000 55. Mounting Plate 136076 Contact Board and Wire Assembly,

Deluxe 138879 Receptacle, 15B 131890-

WURLITZER Page 35C

SECTION C

Page 36C

- WURLITZER

SECTION C

- CAM AND GEAR ASSEMBLY ILLUSTRATED PARTS LIST

- 1. Plate and Pivot Pin Assembly 137897 23. Lever Bearing and Pin Assembly 2. Actuating A r m and Hub Assembly 137928 Tone A r m Feed -In 137918 3 . Actuating Arm and Hub Assembly 137933 24. Retaining Ring 73724-25 - 4. Spring, Record Takeout Segment Gear 133096 25. Mounting Bracket and Spacer Assembly 137956 5 . Segment Gear, Record Trans fe r 137936 26. Motor and Gear Assembly 136782, 6 . Roller Bracket Assembly 137937 Gear, Motor 135259-

- 7 . Mounting Bracket, Transfer Switch 137954 Roll Pin 73782-32 8 . Switch, Transfer 138772 Plug, 2 129377

Tapping Plate 128283 Contact Terminal (2) 132001 9 . Shaft and Gear Assembly, 27. Motor Brake Assembly 136783 - Record Trans fe r 137905 Mounting Plate and Pin Assembly 133484

10. Retaining Ring (2) 73728-37, Lever and Pad Assembly 133429 11. Cam Assembly 137943 Spring, Motor Brake 133428- - - Spacer 141382 Locknut, 4 -40 74988-7 12. Lever, Bearing and Pin Assembly, Washer 53519

Record Clamp 137907 Roll Pin 73782-2 -- 13. Spring, Clamp Lever 137911 Solenoid 133483- - 14. Bsshing, Side Plate (4) 137904- Washer (2) 32629 15. Tapping Plate (used with Item 16) (2) 128283 28. Support, Shaft, Record Trans fe r 137926 16. Play Switch 137952- 29. Shaft, Record Trans fe r 137927 - Cancel Switch (not shown) 137952- 30. Retaining Ring 73724-25 17. Cam and Hub Assembly 137948- 31. Lever Bearing and Pin Assembly,

Set Screw, 8-32 x 3/16 CUP (2) 73511-29 - Record Release 137921 18. Plate and Pivot Pin Assembly 137893 32. Retaining Ring 73724-18 - 19. Retaining Ring (2) 73724-25 33. Link, Record Release 138017 20. Spacer (4) 137960 21. Lever Bearing and Pin Assembly,

- Tone A r m Lift 137917 22. Mounting Plate. Pin and Spacer Assembly 137913

WURLITZER Page 37C

SECTION C

WURLITZER

SECTION C

RECORD CHANGER ILLUSTRATED PARTS LIST, R.H . 1. Switch, Service 121301 31 . Spring, Turntable Return 2 . Locating Plate, Record A r m Assembly 136366 (6 1/2 oz . a t 1 1/2") 133543 3 . Pivot Bracket and Stop Nut Assembly 128611 3 2 . Bracket and Stop Nut Assembly,

Set Screw, 6-32 x 1/2 Oval 73515-24 Turntable Stop 133973 4 . Stop and Bearing Assembly, L.H. 128609 3 3 . Link, Tone Arm Lift 133395

Spring Washer 73632-4 Retaining Ring (2) 73724-18 * Washer 54024 34. Spring 59612 - Retaining Ring 73724.18 - 35. Lift Lever Assembly, Tone A r m Lift 133137

5 . Mounting Bracket, Safety Switch 137225 36. Spring 115821 - 6 . Adjustment Plate, Safety Switch 137231 3 7 . Plate and Pin Assembly 137974 7 . Switch 138614 Cable Assembly 137976 8 . Pivot Bracket 137988 Retaining Ring (2) 73724-18--

Bushing 137967 38. Thumbscrew 192113- 9 . Stop and Bearing Assembly, R.H. 128610- 39. Brush Holder 1352

Spring Washer 73632-4 Brush 135180 3"" Washer 54024 40. Record A r m Rest and Nut Assembly 1328PP2-~: Retaining Ring 73724-18 -41. Clamp Bracket and Handle Assembly 198165

10 . Pivot Bracket and Stop Nut Assembly 128611 42. Shaft and Lever Assembly Set Screw, 6-32 x 1/2 Oval 73515-24 Turntable Reset 138300

1 1 . Shaft and Lever Assembly 137984 Spring 59894 - 1 2 . Retaining Ring 73724-18 43. Lever and Hub Assembly 1 3 . Lever and Shaft Assembly, Turntable Reset 128229

Record Clamp 137977 Spring 5 9 6 1 2 ~ . 1 4 . Spring, Record Release (7 1 /2 oz. at 1") 138033 44. Mounting Bracket and Bushing Assembly 137192 5 Pivot Bracket 137988 ~ o u n t i n g Bracket and

Bushing 137967 Bushing Assembly (not shown) 128226 1 6 . Link, Turntable Shift 137990 - 45. Link Assembly, Playmeter 138018 17. Spring, Turntable Release Link, Playmeter 138019

( 4 5/16 oz . a t 2 5/16") 65096- Link, Offset, Playmeter 138020 18. Bulb *305 135165 Screw, Red (2) 136509

Light Socket 122358 Washer (2) 12120 19. Link, Turntable Shift 137989 - Retaining Ring (2) 73724-18 -

Retaining Ring 73724.18- Counter Lever, Hub and 20. Adjusting Plate, T r i p Switch 136175 Pin Assembly (not s h w n ) 138027 21. Mounting Plate and Stop Nut Assembly 136412 Bracket and Pin Assembly, 22. T r i p Switch and Plug Assembly 133974 Playmeter (not shown) 138024

Switch, T r i p 121229, 46. Link and Pin Assembly 128614 Plug, 3 137254 Retaining Ring (2) 73724-15- Pin Termina l (2) 132000 47. Link and Pin Assembly 136027

23. Spring 134759 Retaining Ring 73724-18- 24. Bracket and Stop Nut Assembly. 48. Spring 59606

Tone Arm 132991- 49. Solenoid and Plug Assembly 142879 25. Support, Record Changer(4) Link, Solenoid 136714.-

( F o r Service Only) 134906 Shoulder Screw 129819 26. Retainer, Chass is Spring (2), Spacer 129818

Part of Item 29 134735 - Stop Nut, 4-40 74988-7 27. Spring (2), Part of Item 29 61059 Bracket, Solenoid 136713 28. Retainer, Chass is Spring (2) 50. Switch (2) 128344 -

Part of Item 29 136506 Tapping Plate 128283 29. Channel and Spring Assembly, R.H. 140392 51. Mounting Bracket 136030

Spring 140805 52. Adjustment Plate and Pivot Assembly 135989 Wing Nut 76623-4 53. Ball Race 59679

3 0 . Receptacle, 6 131171 54. Mounting Plate and Pin Assembly 140334 Contact Terminal (3) 132001

WURLITZER Page 39C

SECTION C

WURLITZER

SECTION C

- TURNTABLE AND MOUNTING PLATE ASSEMBLY ILLUSTRATED PARTS LIST

- 1. "0" Ring 2 . Retaining Ring 3 . Drive Wheel Assembly 4 . Shim Washer 5 . Retaining Ring 6 . Cup Washer 7 . Spring, Shift, Turntable Drive 8 . Spring, Drive Wheel A r m

(6 1 /2 oz . a t 1 1/8") 9 . Arm, Hub and Link Assembly

10. Shaft, Pivot, Bell Crank - 11. Spring, Turntable Return (6 1/2 o z . x 1 1/8")

1 2 . Retaining Ring (2) - 1 3 . Bell Crank and Hub Assembly, L.H .

1 4 . Spring, Solenoid Assis t (8-10 oz . at 2 5/16")

1 5 . Retaining Ring (2) - 1 6 . Shaft, Solenoid, Bell Crank 17. Plunger, Solenoid 18. Solenoid and Plug Assembly - Solenoid

Plug - 3 Pin Termina l (2)

- 19. Retaining Ring 20. Washer 21. Washer, Fel t

128579 - 2 2 . Receptacle - 3 73724-25 Contact Te rmina l (2)

128032 23. Micro Switch 135057 Tapping Plate

73724-25 Plug - 3 124530 Pin Termina l (2) 128534- 24. Mounting Plate, Speed Change

25. Motor and Sleeve Assembly 133543 Plug - 2 128537 Pin Termina l (2) 124519- 26. Oil Tube

Washer 133543 Cable Clamp

73724-18- 27. Mounting Bracket, Turntable Plate 128046 28. Rubber Mount (4)

Nut (8) 124487 - Lockwasher (8)

73724-15.- 29. Motor Mounting and 124518.~. Pivot Bracket Assembly

121095A 30. Mounting Bracket, Turntable Plate 129423,. 31. Bell Crank and Hub Assembly, R.H. 121095 32. Mounting Plate and Roller Assembly 130253 Spacer, Cover (2) 132000 Lockwasher (2)

73727-50 Washer (4) 124521 33. Cover, Turntable 124520

- WURLITZER Page 41C

SECTION C

TONE ARM ASSEMBLY ILLUSTRATED PARTS L E T

1. Tone Arm and Pivot Rod Assembly

Tone Arm Balance Bracket and

Weld Screw Assembly Pivot Stud Pivot Screw Sleeve Bushing (2) Weight (2) Nut, 10-32 (2)

2 . Wire and Plug Assembly Wire and Clip Assembly Plug (6) Pin Terminal (3) Speed Nut (4) Speed Nut

3 . Mounting Bracket and Stop Nut Assembly

Pivot Screw, Tone Arm 4 . Adjusting Bracket and

Stop Nut Assembly Set Screw,

8/32 x 3/16 Cup (2) 5 . Spring

( l l b . 12 oz. a t 15/16") 6 . Washer (2) 7 . Ball Race, Tone Arm Shaft

8 . Support Casting and 132850 Bushing Assembly 128069 132846 9 . Mounting Bracket, Tone Arm 132928

10. Spring 133544 (3 1/2 oz . a t 1 1/8") 59710 135836 11. Adjustment Lever and 135835 Hub Assembly 133127 135262 12 . Washer (2) 59864 135260 13 . Spring 139695 ( 1 lb. 12 oz . a t 15/16") 59615-

73603 -8 14 . Lever and Bushing Assembly 133074.- 140339 15 . Retaining Ring 73727 -50 138664 16. Retaining Ring (3) 73724-25 131172 17 . Pivot Arm and 132000 Pin Assembly 136410

73655-6 Set Screw, 73655-5 8/32 x 3/16 Cup (2) 73511-29 "-'-

18. Cup Washer 128030 140375 r 19. Spring 128008 135928 20. Cup Washer 124530

21. Gripring (2) 76922-12 140379 22. Link, Tone Arm Feed-In 139929

23. Retaining Ring (2) 73724-18 73511-29e 24. Tube, Tone Arm 140346

25. Shaft, Tone Arm 135795 59615 - 26. Cartridge 138662

128072 Needle, Double Tip Diamond 139008 128491 - Needle, Sapphire 139009

Page 42C WURLITZER