wtp 204 finishing works 1

MINISTRY OF EDUCATION, MALAYSIA

December Edition2013

MINISTRY OF EDUCATION, MALAYSIAVOCATIONAL COLLEGE STANDARD CURRICULUMCOURSE INFORMATIONCOURSE NAME:FINIHSING WORKS I

CODE NAME:WTP 204

LEVEL:1 SEMESTER 2

CREDIT UNIT:2.0

CONTACT HOUR:FACE TO FACE:4.0 HOURS/WEEK

NON FACE TO FACE:

COURSE TYPE:VOCATIONAL

PREREQUISITE:-

CORE REQUISITE:-

COURSE OUTCOMES:

At the end of the course, students should be able to:-

1. select proper materials for wall finishing2. prepare vertical backing surface3. prepare adhesives for tiling and mosaic fixing 4. perform tiles laying on walls.5. perform rendering for backing surface6. perform tiles and mosaic laying on floor.7. identify, select and prepare materials for painting work8. prepare background surfaces suitable for painting works9. perform water-based and oil-based painting worksCOURSE DESCRIPTIONThis course is designed as an introduction for students who wish to develop their competency relating to methods in servicing and maintaining work place tools and equipments based on identification of materials for walls and floor finishing by using blue print, work specification, catalogue and brochures. The students will also be able to prepare good vertical backing surface to receive finishing and prepare good adhesives for tiling and mosaic fixing using blue print, work specification, tools, scaffolding, brochures and tools.

This course will also focus on setting out and laying tiles on walls, on floor in a proper setting out using work specification, appropriate tools, equipment and materials. Beside, students also will be able to identify, select and prepare materials and background surfaces by performing water base or oil base painting according to proper method using blue print, work specification, appropriate tools, equipment and materials. Workplace safety and cleanliness guidance are also included in this module that contributes to the state of knowledge about finishing work. CONTENT AND LEARNING STANDARDS

PROGRAMME:CONSTRUCTION TECHNOLOGY

COURSE NAME:FINISHING WORKS I

CODE NAME:WTP 204

CONTENT STANDARDLEARNING STANDARDPERFORMANCE CRITERIA

1. Select proper materials for wall finishing

1.2 Identify the location.1.1.1 Confirm suitable site condition according to the work specification.

1.3 Identify proper materials 1.2.1 List out the materials for wall finishing according to work specification.

1.4 Prepare adequate materials 1.3.1 Describe the functions of the selected materials in accordance with manufacturer's instruction and specification.1.3.2 Confirm proper types of materials for

Wall finishing using blue print according to

Job specification.

1.5 Examine the quality of selected materials.1.4.1 Specify the quality of materials using proper method in accordance to standard quality requirements and the product manual.

1.6 Store all selected materials 1.5.1Place materials in a safe and proper condition as required according to specification.

CONTENT AND LEARNING STANDARDS



CODE NAME:WTP 204


2. Prepare vertical backing surface

2.1 Study the work instructions 2.1.1 Interpret work instructions including plans

and operational details as specified in the

job specification.

3. 2.2 Identify type of tools.2.2.1 Select tools and equipment for preparing vertical backing surface selected according

to work specification.

4. 2.3 Identify types materials 2.3.1 Select materials for vertical backing surface according to work specification.

5. 2.3.2 List down types of materials in accordance to standard quality

requirements and the product manual.

6. 2.4 Identify and erect required scaffoldings 2.4.1 Select required scaffolding according to

work instructions and operational details.2.4.2 Assemble required scaffolding parts to comply with work instruction and operation details

7. 2.5 Carry out preparation work for vertical backing surfaces2.5.1 Construct vertical backing surface according to job specification2.5.2 Perform work for preparing vertical backing surfaces according to instruction and work procedures as stated in specification.




CODE NAME:WTP 204


8. Prepare adhesives

for tiling and mosaic fixing

3.1 Identify suitable types of adhesives

3.1.1 Select types of adhesives to be used in

accordance to manufacturer's directions and the product manual.

4 3.2Identify the proportion of materials for adhesive 3.2.1 Apply proper proportion of adhesives

materials in accordance with standard work

practices and the manufacturers

recommendation and specification.

5 3.3Compose adhesives materials

3.3.1 Mix adhesives for tiling and mosaic fixing in accordance to work specifications and adhesives brochures.




CODE NAME:WTP 204


6 Perform tiles laying on walls.4.1 Identify tools and equipment 6.1.1 Select tools and equipment according to work specification.

7 4.2 Identify proper and safe location 4.2.1 Select suitable and safe site location according to the work placement.

8 4.3 Plan work procedure relating to the work sequence.

4.3.1 Interpret blue print by referring items sequentially according to the suitability of placement procedure.4.3.2 Organize works systematically according to job specification

9 4.4 Prepare materials 4.4.2 List types and identification of materials according to standard requirement.4.4.3 Describe the usage of materials according to manual specification .4.4.4 Select required materials in accordance with the manufacturer's specifications and the product manual.

10 4.5 Prepare required scaffolding for high working area

4.5.1Erect required scaffolding in accordance with operational details and work specification.

11 4.6 Prepare adhesives 4.6.1Mix adhesives required using correct procedures as stated in the manufacturers specification and the product manual.

12 4.7 Prepare tiles laying on walls4.7.1 Set out the tiles laying work in accordance with the blue print and work specification.

13 4.7.2 Carry out tiles laying on walls in accordance with job specification




CODE NAME:WTP 204


14 Perform rendering for backing surface5.1 Prepare backing surface for rendering work 5.1.1Ensure backing surface is ready or rendering in accordance with the work specification.

15 5.2 Prepare proper materials for rendering.5.2.1 List types and identification of materials according standard requirement.5.2.2 Describe the usage of materials according to manual specification .5.2.3 Select required materials in accordance with the manufacturer's specifications and the product manual.

6 5.3 Identify proper tools needed.5.3.1 List types and identification of tools according standard requirement.5.3.2 Describe the usage of tools according to manual specification .5.3.3 Select the right tools and equipment in accordance with the manufacturer's instruction and work specification.

7 5.4 Prepare mixing of materials for rendering work 5.4.1 Mix the materials required for rendering using the manufacturer's instruction and the product manual.5.4.2 Apply materials required for rendering work using the manufacturer's instruction and the work specification.

8 5.5 Prepare rendering work to specific thickness and finish 5.5.1Carry out the rendering work to specific thickness and finishing for backing surface according to the required work specification.




CODE NAME:WTP 204


9 PERFORM tileS LayING on floor.

6.1 Identify the location of work area 6.1.1 Select suitable work site location according to the suitability of the work site

10 6.2 Plan work procedure relating to the work sequence.

6.2.1 Interpret the blue print according to items and work sequence as specified in the work specification.6.2.2 Organize works systematically according to job specification

11 6.3Identify proper tools and equipment.6.3.1 List types and identification of tools according standard requirement.6.3.2 Describe the usage of tools according to manual specification .6.3.3 Select the right tools and equipment in accordance with the manufacturer's instruction and work specification.

12 6.4Identify proper materials needed.6.4.1 List types and identification of materials according standard requirement.6.4.2 Describe the usage of materials according to manual specification .6.4.3 Select required materials in accordance with the manufacturer's specifications and the product manual.

13 6.5Prepare work surface appropriately.6.5.1 Clean up the floor surface using proper procedures according to the work specification.

14 6.6Examine the condition of the tiles pieces.6.6.1Check the tile pieces regularly to conform the quality requirements and work specification.

15 6.7Prepare tiles laying on the floor.6.7.1 Set-out the tiles laying on the floor using proper procedures according to the blue print and specification.6.7.2 Carry out tiles laying on floor in accordance with job specification




CODE NAME:WTP 204


7. perform mosaic Laying on floor.7.1 Identify the location of work area7.1.1 Select suitable site location in accordance to the suitability of the work site.

8 8.1 Identify proper tools and equipment8.1.1 List types and identification of tools according standard requirement.8.1.2 Describe the usage of tools according to manual specification .8.1.3 Select the right tools and equipment in accordance with the manufacturer's instruction and work specification.

9 9.1 Identify proper materials needed.7.3.1 List types and identification of materials according standard requirement.7.3.2 Describe the usage of materials according to manual specification .7.3.3 Select required materials in accordance with the manufacturer's specifications and the product manual.

10 10.1 Conduct setting out and design mosaic laying on the floor

7.4.1 Set-out mosaic laying on floor according to job specification

7.4.2 Design mosaic laying on the floor using proper procedures according to the blue print and work specification.

11 11.1 Prepare required adhesive adequately7.5.1 Mix adequate required adhesive by proper procedures in accordance with manufacturer's instruction and the "Product Manual.

12 12.1 Lay the mosaic on floor.7.6.1 Fix the mosaic on floor using proper procedures to comply the blue print and work specification.

13 13.1 Carry out finishing work on the mosaic surfaces 13.1.1 Apply finish technique for mosaic using proper procedures to comply with the blue print and work specification.




CODE NAME:WTP 204


8. Identify, select and prepare materials for painting work

8.1 Plan work procedure 8.1.1 Interpret the blue print according to items and work sequence as specified in the work specification.

8.1.2 List down the work sequence according to the blue print and the work specification.8.1.3 Organize works systematically according to job specification

14 8.2 Establish suitable types of painting work (exterior or interior) 8.2.1 Recognize the types of painting work needed in accordance with the work specification , manufacturer's directions and the product manual.

15 8.3 Determine types of background for painting work .8.3.1 Recognize the types of background for painting work according to the work specification.

16 8.4 Establish proper materials for painting work.8.4.1 List types and identification of materials according standard requirement.8.4.2 Describe the usage of materials according to manual specification .8.4.3 Carry out preparing the right materials in accordance with the manufacturer's instruction and work specification.

17 8.5 Establish proper tools and equipment.8.5.1 List types and identification of tools and equipment according to standard requirement.8.5.2 Describe the usage of tools according to manual specification .8.5.3 Carry out preparing the right tools and equipment in accordance with the manufacturer's instruction and work specification.

18 8.6 Establish suitable types of paints

8.6.1 Carry out preparing paint for painting work using proper procedures and in accordance to the manufacturer's directions and product manual.




CODE NAME:WTP 204


19 Prepare background surfaces suitable for painting workS 9.1 Identify the location of work and surfaces 9.1.1 Select suitable location and surfaces according to the suitability of work placement.

20 9.2 Identify tools, equipment and materials needed9.2.1 List types and identification of tools equipment and materials according standard requirement.9.2.2 Describe the usage of tools equipment and materials according to manual specification .9.2.3 Select the right tools equipment and materials in accordance with the manufacturer's instruction and work specification.

21 9.3 Erect scaffoldings for high working area

9.3.1 Specify the right scaffolding according to job specification9.3.2 Select the required components for scaffolding according to manual specification 9.3.3 Assemble all components for scaffolding erection according to standard requirement and work specification.

22 9.4 Identify remedial work on imperfection of the background surface 9.4.1 Perform remedial work on imperfection of the work surface using proper procedures as in the work specification




CODE NAME:WTP 204


23 Perform water-baseD painting workS 10.1 Identify location with good ventilation.10.1.1 Select location with good ventilation by considering the suitability of the work placement.

24 10.2 Identify tools and equipment. .10.2.1 List types and identification of tools according standard requirement.10.2.2 Describe the usage of tools according to manual specification .10.2.3 Select the right tools and equipment in accordance with the manufacturer's instruction and work specification.

25 10.3 Prepare materials.10.3.1 List types and identification of material according standard requirement.10.3.2 Select the right material in accordance with the manufacturer's instruction and work specification

26 10.4 Erect scaffoldings for high working area

10.4.1 Specify the right scaffolding according to job specification.10.4.2 Select the required components for scaffolding according to specification 10.4.3 Assemble all components for scaffolding erection according to standard requirement and work specification

27 10.5 Conduct water-based painting10.5.1 Define water-based painting works according to specification

10.5.1 Carry out water-based painting work using proper method in accordance with the blue print and work specification.

28 10.6Maintain work area and equipment.10.6.1 Clean up the work area and equipment in accordance with the job specification.10.6.2 Store all equipment in a safe place and condition according to the standard operating procedures.




CODE NAME:WTP 204


11 Perform oil-baseD painting workS

11.1 Identify the suitable location with good ventilation.11.1.1 Select location with good ventilation by considering the suitability of the work placement.

12 11.2 Identify proper tools and equipment.11.2.1 List types and identification of tools according standard requirement.11.2.2 Describe the usage of tools according to manual specification 11.2.3 Select the right tools and equipment in accordance with the manufacturer's instruction and work specification.

13 11.3 Prepare proper materials.11.3.1 List types and identification of materials according standard requirement.11.3.2 Select the right materials in accordance with the manufacturer's instruction and work specification.

14 11.4 Erect required scaffoldings for high working area

11.4.1 Specify the right scaffolding according to job specification.11.4.2 Select the required components for scaffolding according to specification 11.4.3 Assemble all components for scaffolding erection according to standard requirement and work specification

15 11.5 Perform oil-based painting as required 11.5.1 Define oil-based painting works according to specification.11.5.2 Carry out oil -based painting work using proper method in accordance with the blue print and work specification.

16 11.6Maintain work area and equipment.11.6.1 Clean up the work area and equipment in accordance with the job specification.

11.6.2 Store all equipment in a safe place and condition according to the standard operating procedures.

Last Edited10-13 Nov 2013

Course Page22/22Document Page22

wtp 204 finishing works 1

Documents