wt4603 unit3 week4

WT4603 Wood Processing Safety & Practice

Lecture Unit 3 (Week 4)

Personal Protective Equipment (PPE) & Week 5 Labs (Component B & Routers) Lecturer: Mr. Joseph Lyster [email protected] Notes prepared by: Mr. Donal Canty, Mr. Des Kelly and Mr. Joseph Lyster Notes available on www.slideshare.net/WT4603

mailto:[email protected]

http://www.slideshare.net/WT4603

WT4603 Wood Processing Safety and Practice

PPEPERSONAL PROTECTIVE EQUIPMENT

Department of Manufacturing & Operations Engineering

WT4603

Personal Protective Equipment (PPE)


WT4603

Personal protective equipment• For centuries, people have

employed the use of Personal Protective Equipment (PPE).

▫ Cowboys wore leather chaps.▫ Eskimos wear thick gloves and

coats.▫ Medieval knights wore Armour.▫ Soccer players wear shin guards.


WT4603

What is PPE?

“All equipment which is held or worn at work to protect a person from any

harm or environmental hazards encountered.”

http://en.wikipedia.org/wiki/Personal_protective_equipment


WT4603



Environmental Hazards

Noise Dust Smoke Unsafe Machinery Etc.

• There are 5 main classes of environmental hazard:1.Chemical2.Physical3.Mechanical4.Biological5.PsychologicalDepartment of Manufacturing & Operations Engineering

WT4603

Hierarchy of risk control

1. Eliminate the Hazard Completely.2. Substitute Hazard with a safer alternative.3. Isolate the Hazard.4. Use engineering controls to reduce risk at the source

(Guarding).5. Provide training on how to avoid risks.

& if all that fails…

6. Use PPE.

MOST PREFERABLE SOLUTION


WT4603

Using P.P.E.The use of PPE is a last resort!

• It should only be relied upon for protection when all other means of controlling a hazard have been eliminated as possibilities.

• It is much more desirable to completely eliminate the hazard than to safeguard against it.

• Prevention is better than cure!!!

PPE should be used:▫ Where Engineering (Guarding) or Administrative (Training, Rules) controls are not

feasible.▫ As a short-term measure during periods of time when engineering or

administrative controls are being implemented.▫ During emergency response situations.


WT4603

PPE Legislation• Safety Health and Welfare at Work (Control of Noise at Work)

Regulations 2006.▫ Act specifically outlining the requirements to protect the hearing of

employees in the workplace.

• Safety, Health and Welfare at Work Act 2005. (Formerly 1989 Act)▫ General Act Governing health and Safety at work in Ireland

• The Safety, Health and Welfare at work (General Application) Regulations 2007.▫ Among other things, this Act outlines the legal responsibilities in relation

to the use of PPE in the workplace & schools.

• European Communities (Personal Protective Equipment) Regulations, 1993.▫ Aimed more specifically at the selection, use and manufacturing quality of

PPE.Department of Manufacturing & Operations Engineering

WT4603

Responsibilities of Employers*• All employers must conduct a Hazard Identification and risk assessment

to determine if the use of PPE is necessary.

• Risk control; this may be through the use of PPE.

• Provision of PPE on the basis of the Hazard Identification.

• Provision of Training on using necessary PPE.

• The Safety, Health and Welfare at work (General Application) Regulations 2007 requires schools to provide suitable PPE if a risk to health and safety cannot be avoided or sufficiently controlled through other means.

*The Safety, Health and Welfare at Work Act 2005.*The Safety, Health and Welfare at work (General Application) Regulations 2007.


WT4603

Responsibilities of Principals• They should:

▫ Carry out a risk assessment to identify the possible need for PPE.▫ Provide, free of charge, adequate PPE to employees (Teachers) who may be

exposed to hazards at work that have not been controlled by other means.▫ Make an assessment before choosing any form of PPE.▫ Ensure that PPE is well maintained and cared for.▫ Provide storage for PPE when not in use.▫ Provide teachers with training in the use, limitations and care of their of

PPE


WT4603

Responsibilities of Teachers (Employees)

•Employees must:▫Attend PPE training.▫Make full and proper use of PPE.▫Ensure PPE is correctly stored

and cared for.▫Follow all directions and heed all

warnings.▫Report any defects in or loss of

PPE to employer.


WT4603

Provision of P.P.E. • The employer should shoulder the cost of all PPE

required by the employee.

• In schools, this means that any teachers requiring it, should be provided with a full set of PPE by the school.

• It should be made mandatory that all pupils should be required to provide their own PPE (to the appropriate standard).

• Wearing of this PPE should be strictly enforced by the teacher.

• Employer must maintain and replace broken or un-usable PPE.▫ However, it is the responsibility of each employee to

respect and care for their PPE and report any damage or defects present in it to the employer.


WT4603

PPE Training*• Employers must provide the following training

in relation to PPE:▫ Proper use of PPE.▫ When to use PPE.▫ Adequate PPE Storage.▫ Importance of using PPE.▫ How to spot defects in PPE

• Teachers should also provide training to their pupils on how to use their PPE correctly.

• Part of a teachers demonstrations should place an emphasis on ▫ The correct use of PPE▫ Importance of PPE▫ Care of PPE.


WT4603

Sharing PPE • Under no circumstances should pupils be allowed to share PPE.

Why Not?• Associated hygiene issues.• Swapping PPE may limit the level of

protection offered:▫ Different size/Setting.

Make sure everyone has their own!!!


WT4603

PPE Selection• In schools, the selection of PPE is generally the

responsibility of the teacher.

• For this reason, it is vital that teachers are capable of making the correct selection of PPE both for themselves and the pupils left in their care.

• When selecting PPE, always think of the worst case scenario – What is the worst that could happen?

• The existence of the “CE” marking on a piece of equipment should indicate that its manufacturer has met all relevant safety standards and requirements.▫ ALWAYS look for this mark when buying PPE (as

well as other equipment, tools and machinery.)


WT4603

PPE – Some Factors to Consider• DEGRADATION

▫ Harmful change of physical properties of a protective clothing material when subjected to a chemical or wear and tear over time.

• PENETRATION▫ Flow of chemicals/ hazardous substances through

seals such as zips, seams or pinholes.

• PERMEATION▫ Movement of the hazardous substance through the

protective material itself.

Always consult manufacturer’s instructions.Department of Manufacturing & Operations Engineering

WT4603

Eye & Face Protection• Thousands of people are blinded in

the workplace every year for no reason.

• Simple and inexpensive face and eye protection could have prevented it.

• The human eye is very sensitive organ and is highly susceptible to injury from many sources:▫ Impact ▫ Chemicals▫ Dust/ foreign particles.▫ Etc..


WT4603

The eye• The Cornea & Lens focus light.• The Iris controls the amount of light entering the eye.

All are made up of very soft, delicate and easily damaged tissue.

Damage is often irreparable!


WT4603

Common Eye Injury Causes

• Objects hitting the eye ▫ Swarf.▫ Flying particles (Sawdust).▫ Flying objects (Projected materials/

tools!)

• Intense Light (Lasers, Welding)• Contact with Chemicals.• Falling onto or walking into stationary

objects.


WT4603

Chemicals/ fumes/ mists• Spray Paint.• Fumes from welding and other heat

processes.• Smoke.• Aerosol Cans.• Liquid droplets.

• Airborne Hazardous chemicals can enter and damage the eye.


WT4603

Flying particles• Grinding • Hammering • Welding• Splashes of chemicals and

molten metals

• Physically injure the eye, tearing or scratching the cornea.

• Very painful and difficult to correct.


WT4603

Thermal

•Heat and glare from molten metals, furnaces and other heat processes such as welding or soldering can burn the cornea.


WT4603

Intense light levels

• Lasers• Exposures to excessive

glare or bright lights • Damage the retina and

optic nerve located deep within the eye as opposed to swarf or dust just damaging the cornea.▫A much more serious

injury.


WT4603

Safeguarding against Eye Injuries

• Eye protection should be worn when spray painting, grinding, drilling, welding, sawing, working in a dusty environment, or handling chemicals.

• One should also develop the good habit of protecting the eyes whenever working with hand or power tools.

WHEN IN DOUBT, WEAR EYE PROTECTION ANYWAY!


WT4603

Machinery Guarding

• Because it is much more preferable to eliminate the hazard at the source, guarding is often added.

• This is not usually enough to fully reduce the risk so wear safety glasses as well!!


WT4603

Ventilation• Ventilation is the movement of air, usually

between the inside and outside of enclosed spaces.

• Ventilation is necessary when people or animals are present to remove carbon dioxide and replace it with oxygen.

• Ventilation must also be used to remove dangerous pollutants such as smoke, fumes, chemicals and fine particles suspended in the air.


WT4603

Safety Glasses/goggles

• Safety glasses usually have frontal protection only.

• Safety goggles fit closer to the face and protect the eyes from frontal as well impact from all other directions.▫ Much more resistant to airborne hazards

• Airborne hazards such as fine particles and dust may by-pass safety glasses.

• Check for “CE” marking.

• Different Grades available for different hazard levels.

• Prescription safety glasses also available.


WT4603

Face Shields• Should be used in conjunction

wit glasses or goggles where possible.

• Not considered suitable eye protection on its own.

• Offers very little protection against strong impact ▫ More suitable for dust and small

flying particles (Lathe Work).


WT4603

NOTE: “CE” Marking


WT4603

Welding Goggles/Shield/Helmet• The brilliant light from welding can cause

serious damage to the eye even when exposed to it for a short period of time.

• A welding helmet is fitted with a special lens to filter extreme bright light from welding while the helmet itself protects against hot sparks.

• Anyone watching the welding should also utilise suitable PPE.

• When chipping slag, ensure that you, as well as anybody else watching, is wearing suitable eye protection!


WT4603

Care of Eye Protection

•Clean with wipes or water.•Don’t use abrasive soaps.•Store in a clean, dry and

dust-free place.


WT4603

Eyewash Stations• Install and Maintain

▫ Display instructions.▫ Train on how to use.▫ Keep fully stocked.

• Some chemicals react with water – ▫ Consult Material Safety Data

Sheet (MSDS)


WT4603

Of course, wearing safety glasses doesn’t

necessarily mean you are going to be safe from everything!!

USE YOUR COMMON SENSE!!!


WT4603

Respiratory Protection


WT4603

The Breathing Process• To best understand the hazards one should

take a look at how breathing works

• Take a breath and air rushes from the external environment, down the windpipe and into the alveoli in the lungs.▫ Alveoli in lungs are tiny air sacs which

transfer oxygen into blood and CO2 from it.

• The lung is a very delicate organ and can be easily damaged by hazardous dusts, fumes and chemicals when inhaled.

• Damaged lungs are also much more susceptible to contracting further diseases.


WT4603

Dust• Dust is formed when material is broken

down into tiny particles.▫ Grinding.▫ Sanding.▫ Cutting.

• The Safety, Health and Welfare at Work (Chemical Agents) Regulations 2001 requires all schools to assess and determine the risk posed by any chemical agent including wood dust.


WT4603

Wood Dust

•Machining Processes:▫MDF and hardwood dust

is considered to be a significant hazard.

•Sanding – ▫Fine dust that may even

stay airborne for hours after work has ended.


WT4603

Carcinogens • A carcinogen is any substance or agent that promotes cancer.▫ Softwood dust – Non-Carcinogenic.▫ Hardwood dust – Carcinogenic.▫ MDF - Carcinogenic.

• Due to the carcinogenic nature of these materials, they should be phased out completely in the technology classrooms.▫ At a minimum, PPE and dust extraction should be

available.

• It is the responsibility of the employer to monitor and control the use of carcinogenic materials and substances in the workplace.*▫Storage.▫Training.▫Control Measures or suitable PPE.

*Safety, Health & Welfare at Work (Carcinogens) Regulations, 2001.


WT4603

Vapors• A vapor is created when a liquid or

solid evaporates.

EXAMPLES▫ Petrol vapors.▫ Wood finishes▫ Paint.▫ Thinners▫ Solvents


WT4603

Mists and Sprays

•Mists and sprays are made up of small droplets suspended in the air.

•Aerosols and spray guns, by design, create fine sprays and mists.

EXAMPLES▫Paint▫Water


WT4603

Gases, fumes & SmokeGAS

• May or may not have a smell.• May or may not be visible.

FUMES• Occur during high heat process such as

welding or soldering.

SMOKE• The suspension in air of small particles

resulting from the incomplete combustion of a fuel.


WT4603

Respiratory Protection

• Hazardous substances which have become airborne pose a significant threat to the lungs and therefore we must protect ourselves against them in some way

• The aim should always be to prevent the substance from getting into the air in the first place but when this is not possible, Respiratory Protection should be used.


WT4603

Respirators

• All respirators have some form of face piece which is held to the face with straps, usually around the head.

• Half-face respirators cover the nose and mouth only and are for use where the contaminants are not a threat to the eyes or face.

• A full-face respirator covers all the face and should be used where contaminants may be a hazard to eyes and the face as well as the respiratory system.


WT4603

Respirators

• A respirator is a device which is designed to protect the wearer from inhaling harmful dusts, gases, fumes or vapours.

Two main types of respirator exist:1. Air Purifying Respirators.2. Atmosphere Supplying

Respirators


WT4603

Air Purifying Respirators

• Used against contaminants such as smoke, dust, vapours and fumes.

• Acts passively to remove contaminants from the air.

• The device renders the contaminated air breathable.

• Usually has a filter for particulates or a cartridge for gasses and vapours (or a mixture of both).

•Not suitable where the levels of oxygen in the air are deficient.


WT4603

Filter Mask - Disposable• A filter mask offers protection to its wearer

against airborne substances.

• It usually covers only the nose and mouth and works by restricting the flow of air, forcing it through a filter which removes harmful particles or dusts.

• The most common type is the white disposable N95 filter mask as shown.

• Cannot protect against:▫ Gasses▫ Vapors▫ Low O2 levels


WT4603

Filter Mask - Reusable

• Reusable filter masks fitted with disposable filter cartridges are also available.

• When filters become saturated or worn, or if air flow is restricted they must be replaced.

• Mask cartridges are filled with certain resins or chemicals that will absorb certain fumes, eliminating them from the inhaled air.

• Different cartridges are available for filtering different contaminants from the air. ▫ Check manufacturer’s instructions & Use by date.


WT4603

Atmosphere Supplying Respirators• Air supplied respirators use reserve tanks to supply a constant flow of air

to the wearer’s face/lungs.• The contaminated air is not purified in any way nor is it inhaled by the

wearer.• Fire Fighters• S.C.B.A. – Self Contained Breathing Apparatus• S.C.U.B.A. – Self Contained Underwater Breathing Apparatus


WT4603

Respirator Selection• Hazard level should be determine and

adequate level of protection selected accordingly by a competent person.▫ Determined largely by the hazard present.▫ E.g. - Dust PPE will give no protection against

fumes and vapours.

• Supplied air respirators in schools SHOULD NOT BE USED.

• If any such risk should exist, find an alternative for it!


WT4603

Inspection Before Use

•Check Respirators before you them every time.

• Look out for;▫Wear and damage.▫Cracks▫Loose fittings.▫Use by dates.


WT4603

Monitoring the Respirator

• As you work- you must stay aware of your respirators operation.

• Signs of it not working are:▫ Feeling dizzy or sick.▫ Being able to smell or taste the contaminant

in the air.▫ Difficulty breathing.▫ Filter/ cartridge has expired.▫ Respirator is damaged.


WT4603

Storing • When not using respirators, they must be carefully stored in order to prevent deterioration in their effectiveness.

• Store in a sealable plastic bag and away from:▫ Dust▫ Moisture▫ Direct Sunlight▫ Heat▫ Extreme cold▫ Chemicals▫ Germs/fungal growth▫ Sources of infection.


WT4603

Hearing Protection


WT4603

Noise• Noise is often described as being sound that people would prefer not to

hear.

• What may be important or welcome sound to you may be noise to others exposed to it.


WT4603

Is Noise harming you?

• If you experience any of the following, you may be exposed to excessive noise levels on a daily basis:

• You experience ringing or other noises in your ears.

• You have difficulty hearing people talking.

• You are unable to hear high pitched or soft sounds.


WT4603

Remember!Becoming used to a loud noise is a sign of gradual hearing

loss.

You do not become used to it, you merely lose your ability to hear it!!


WT4603

Ear Protection Zones

• If the risk assessment reveals areas of high noise levels in which ear protection is required, they must designated as Hearing Protection zone

• These zones must be marked clearly using adequate signage.

• The sign should show the following:▫ That you are entering an ear protection

zone.▫ Ear protection must be worn in this area.▫ Nobody may enter the zone without

wearing appropriate hearing protection.

Safety Health and Welfare at Work (Control of Noise at Work) Regulations 2006


WT4603

As a Rule!

If you must shout in order for someone 2 meters away from you to hear you,

YOU SHOULD BE WEARING HEARING PROTECTION!


WT4603

Hearing Protection Devices• Tinnitus and Noise Induced Hearing Loss

can be prevented with the use of appropriate Hearing Protection Devices (HPD’s).

• These devices provide a barrier between the ear and the noise.

• Some ear defenders work on the principle of absorbing the sound waves before they reach the ear.


WT4603

Selecting Hearing Protection

• Ensure a “CE” Marking is present.• Every person is different. – Some find different things more

comfortable than others.• In processes where hands become dirty, inserting and removing

earplugs can lead to dirt and bacteria being introduced into the ear canal causing ear infections.

• Provide and encourage the use of a variety of hearing PPE and let people select most comfortable for themselves.

If PPE is uncomfortable or irritating, It will not be used!!


WT4603

Noise Reduction Ratings• Earplugs and earmuffs come rated with “Noise

Reduction Ratings” (NRR’s).

• This rating tells the user what level of sound protection they can expect from the device in a noisy environment.

• The NRR of hearing protection devices should be consulted when selecting them for use.

• However, NRR’s are developed under controlled laboratory conditions and the “real-life” NRR rating is usually lower. Therefore it is always best to error on the side of caution and select the PPE with a higher NRR than is required.


WT4603

Hearing P.P.E.• If the noise cannot be reduced to

suitable levels at the source, hearing PPE must be used to achieve this.

• Many types of hearing protection devices are available each carrying with them various advantages and disadvantages.

• Popular types of hearing protection devices are:

1 Earplugs 2 Earmuffs


WT4603

When to Wear Hearing Protection.You should consider wearing Hearing Protection if;

• You work in an environment where you are exposed to continuous decibel levels of 80dB or greater over an 8 hour period.

• You are unusually fatigued after being in a noisy area.

• You experience ringing in your ears after being in a noisy area.

• You feel nervous or anxious after being in a noisy area.

• In order to be fully effective, hearing protection devices must be worn at all times in noisy environments.

• Removing for even a short period of time can decrease their effects substantially.


WT4603

Earplugs

• An earplug is a protective device which is inserted into the ear canal to protect the inner ear from being exposed to excessive levels of noise or the intrusion of foreign bodies or excessive wind.


WT4603

http://upload.wikimedia.org/wikipedia/commons/b/b8/Disposable_foam_earplugs.jpg

Earplugs • Most earplugs are cylindrical in shape and are made from memory foam.

• The earplug is rolled into a tightly compressed cylinder between the fingers and inserted into the ear canal.

• When released, the earplug expands to its original size, sealing the ear canal and preventing sound vibrations from reaching the eardrum.

• Other earplugs are custom made with moulds from the user’s ear to provide a more snug and noise resistant fit.


WT4603

Advantages & Disadvantages of Earplugs

ADVANTAGES• Inexpensive• Small & Lightweight• Comfortable in warm, humid environments.• Easily used with other equipment.

DISADVANTAGES• May work themselves loose and require

adjustment or refitting.• Frequently become soiled.• Require specific fitting instructions.• Awkward to remove and replace when noise is

inconsistent.• Easily Misplaced.• May irritate the ear canal.• Difficult to monitor the use of.


WT4603

Earmuffs• Earmuffs are objects which are designed to

cover the ears for protection.• Earmuffs come in two different kinds;

Thermal Earmuffs• Worn in cold environments to keep the ears

warm.

Acoustic Earmuffs• Also known as ear defenders.• Cups lined with sound-absorbent material

which fit over the ears.• Protect the ears from excessive noise levels.


WT4603

Advantages & Disadvantages of EarmuffsADVANTAGES:

• Easy to supervise the wearing of.• More comfortable for long periods of

use.• One size fits all.• Quickly put on & removed.• May be worn with minor ear

infections.

DISADVANTAGES• May fit loosely on the head.• Uncomfortable in a warm

environment.• Difficult to use with some other

equipment.• Less portable and convenient.


WT4603

Wearing Earmuffs

• Earmuffs must fit fully over the outside of the ears.

• Their effectiveness is determined by the quality of the seal around the ear.

• Ensure hair, hats, glasses, jewellery, etc. does not interfere with the seal around the ear.

• A combination of earplugs and earmuffs should be used as an extra precaution if glasses, earrings, facial hair, etc, prevents the earmuffs forming a good seal around your ears.


WT4603

Hearing Protection Overkill

•Wearing excessive levels of hearing protection can also be hazardous!!!

•Employees may not be able to hear vital warning alarms such as fire alarms.

• It also promotes users removing ear protection to talk.


WT4603

Caring for hearing protection devices - Earplugs

• When not using earplugs, they should be stored in a clean, cool and dry place.

• If Foam earplugs become soiled, they should be discarded and replaced with a clean pair.

• Soiled PVC earplugs can often be cleaned with soap and water.

• Replace PVC earplugs if they become torn or brittle.

• Check manufacturer’s instructions regarding washing earplugs.


WT4603

Caring for hearing protection devices - Earmuffs• Always follow manufacturers instructions.

• Check headband regularly for wear and tear-replace or repair immediately if needs be.

• Ensure tension in headband is not reduced.

• Store earmuffs in a clean, cool and dry place when not in use.

• Always replace when a snug fit in or around ear is not achieved.

• Wash earmuffs with a mild liquid detergent. ▫ Do not wet sound-attenuating material within the ear

muffs.


WT4603

Hand Protection


WT4603

Hand Protection• Look at your hands! They are the only two you will ever

have. SO MIND THEM!

• Without the use of your fingers or hands, your ability to work or lead a normal life would be dramatically reduced.


WT4603

Possible Hazards

• Cuts and Abrasions.• Crushing.• Extremes of temperatures.• Contact with toxic or corrosive

substances.• Skin Irritation & Dermatitis.• Electric shock.• Absorption of chemicals.


WT4603

Dermal Hazard Categories• Skin on the hands may come into contact

with a lot of unknown materials and substances from day to day.

• Chemical▫ Irritants.▫ Corrosives.▫ Carcinogens.

• Physical ▫ Fire.▫ Radiation.▫ Vibration.

• Biological▫ Human, animal or environmental pathogens

(Hepatitis, AIDS, etc)

NOTE: poisons and toxins can be

absorbed through the skin in the

hands and into the body.


WT4603

Possible Hazard: Traumatic injury• Sharp tools and machines

may cut your hands.

• Staples, wire, nails chisels etc. can puncture your hands.

• Hands may become caught in machinery causing them to become sprained, crushed or amputated.


WT4603

Selection of Gloves• The correct glove must be selected in

order to achieve an adequate level of protection. The following should be considered:

▫Chemical Resistance.▫Cut/Tear Resistance.▫Manual Dexterity/Flexibility.▫Extremes of Temperature.▫Cost▫Fit.▫Comfort.


WT4603

Types of Gloves

• Metal mesh & Kevlar gloves protect against cuts and sharp objects.

• Leather gloves offer protection against rough objects, chips, sparks and low moderate heat.


WT4603

Types of Gloves• Cotton fabric gloves protect the hands from

dirt, abrasions and splinters.

• Cotton gloves also improve grip when handling slippery objects.

• Offers very little protection against cuts.

• Rubber & Vinyl gloves protect the wearer’s hands from dirt, chemicals and environmental pathogens.▫ Wear around blood

• Should always check packaging and manufacturer’s instructions.


WT4603

Use of gloves

• When wearing gloves;▫ Remove any rings, watches or bracelets that may damage

the gloves or reduce their ability to do their job.▫ Inspect gloves for holes and cracks that might leak.

• Replace gloves that are torn or worn out.

• After working with chemicals, leave gloves on hands and wash under running water to remove any chemicals before you remove gloves from your hands.

• Store gloves in a clean, cool, dry and well ventilated area.

• NEVER wear gloves around powered rotating equipment such as drills or lathes etc…(May become tangled)

• Always follow manufacturer’s instructions.


WT4603

Welding PPE• While working with heat processes such as welding additional

protection will be necessary.

• Infrared radiation produced during welding is a cause of retinal burning and cataracts.

• To protect against this, a proper welding helmet should be worn which incorporates the correct grade of filter plate.

• To protect the body from welding spatter and arc flash, the following protective clothing may be utilised:▫ Flame-proof apron.▫ Gloves.▫ Long sleeves.▫ Fire resistant capes for overhead work.▫ Appropriate footwear

• Keep clothes free of grease and oil.


WT4603

LAB COAT

• A lab coat is a knee-length overcoat worn by those involved in significant work to protect their street clothes.

• The garment is usually made from cotton or linen and is usually white in colour.▫ known not to react with any chemicals.▫ No loose elements.▫ Hygienic.

• Lab coats are much easier to take off than regular street clothes if they get splashed with chemicals, catch fire or become entangled in machinery.


WT4603

Encouraging use of PPE• Students should benefit from good example.

▫ Teacher should wear PPE whenever appropriate.

• Signage.▫ Highlight importance of PPE using

strategically placed safety signs.

• Teach safety as part of working, not just an add-on.


WT4603

Encouraging use of PPE

• The use of suitable signage should be employed to help encourage safe practices and the appropriate use of PPE.


WT4603


WT4603

WEEK 5: LABSComponent B• You will be provided with two pieces of un-sawn material, both measuring 1020 x 145 x 25.• You will label both pieces B1 and B2, respectively.

B1

B2

Table Top

Back/Side Rails & Drawer Front

1020

145

1020

145


WT4603

B1 = Table Top

• B1 must be planed all round (P.A.R) to 1020 x 140 x 22

• The process for B1 will involve the following:

• Surface plane/thickness to 140 x 22• Rip B1 @ 67mm (x2)• Thickness to 65mm (x2)• Cross cut to 500mm (x4)


WT4603

B2 = Back and Side Rails

• B2 must be planed all round (P.A.R) to 1020 x 140 x 20

• The process for B2 will involve the following:

• Surface plane/thickness to 140 x 20• Rip B2 @ 132mm (x1)• Thickness to 130mm (x1)• Cross cut 1 = Side Rails @ 158mm (x2)• Cross cut 2 = Drawer Front @ 272mm

(x1)• Cross cut 3 = Back Rail @ 312mm (x1)


WT4603

Processing Sequence:1. Surface plane face side/face edge for B1 & B22. Thickness 1 = B1 Table Top to 140 x 223. Thickness 2 = B2 Side/Back rails/Drawer Front to 140 x 204. Rip 1 = B1 Table Top @ 67mm (x2)5. Thickness 3 = B1 Table Top to 65mm (x2)6. Rip 2 = B2 Side/Back rails/Drawer Front @ 132mm (x1)7. Thickness 4 = B2 Side/Back rails/Drawer Front to 130mm

(x1)8. Cross cut 1 = B1 Table Top @ 500mm (x4)9. Cross cut 2 = B2 Side Rails @ 158mm (x2)10. Cross cut 3 = B2 Drawer Front @ 272mm (x1)11. Cross cut 4 = B2 Back Rail @ 312mm (x1)


WT4603

Working Drawings

WT4603


Select & Position Dimensions Correctly

WT4603


Arrows & Dimension Lines

WT4603


Consider best location and view

WT4603


Include all details

WT4603


Include Component labelling

WT4603


Exploded View or Assembled View???

WT4603


WT4603


Router Station 1Carry out the following operations:1. Isolate the router. 2. Select V- groove cutting bit.3. Fit the bit in the router securely.4. Set the depth of the cut to 3mm.5. Machine the profile shown on the drawing

using the guide fence. (Note: Guide fence is set. Do not adjust.)

6. Isolate the router.7. Remove the cutter from the router.

FEEDDIRECTION

ROUTER PULLS TO THE LEFT

FENCE PULLED TOWARDS

WORKPIECE


WT4603

Router Station 2Carry out the following operations:

1. Isolate the router.2. Select the bearing guided chamfer bit.3. Fit the bit in the router securely.4. Set the depth of the chamfer to half the

thickness of the material provided. 5. Machine the chamfer profile on the outer edges

of the material.6. Isolate the router.7. Remove the cutter from the router


WT4603


1. Isolate the router.2. Select Ø 6mm cutting bit.3. Fit the bit in the router securely.4. Set the depth of the cut to 5mm.5. Set the depth turret to machine to a depth of

10mm on the second pass.6. Fit the guide fence to the router.7. Set the guide fence to the dimension shown on

the drawing.8. Machine the profile shown on the drawing using

the guide fence.9. Isolate the router.10. Remove the guide fence and Ø 6mm cutting bit

from the router.


WT4603


1. Isolate the router.2. Select Ø 12mm cutting bit cutting bit.3. Fit the bit in the router securely.4. Fix the template guide to the base of the

router.5. Set material in the template.6. Set the depth of the cut to 5mm.7. Set the depth turret to machine to a depth of

10mm on the second pass.8. Machine the profiles of the template using the

template guide.9. Isolate the router.10. Remove the template guide and Ø 12mm

cutting bit from the router.


WT4603


WT4603

What makes a good poster?

TIPS: Layout: Portrait/Landscape All graphics must be sketched Can be done entirely by hand or sketches

can be scanned and the poster electronically edited/formatted.

Main sketch located in centre Render/shade neatly Background colour (electronic only –

optional) Supporting sketches of good proportion

and size Annotations/Information must be clearly

readable from a distance of 5 metres. Information must be labelled and have a

logical sequence i.e. clockwise pattern Text can be typed/printed, in the case of

printing text (by hand) ensure it is of the highest standard.


WT4603

What makes a good poster?• Poster Information:

▫ A2/A3 in size - Laminated▫ Name of Machine▫ Purpose of Machine▫ Machine Provision ▫ CE Marking ▫ Information panel ▫ Safety signage▫ Machine Components▫ Health & Safety Features

• Information Sheet:▫ A4 in size (Laminated)▫ Can be attached to the machine▫ Index of poster information▫ Should further describe components

labelled on main poster

• Activity Sheet:▫ A4 in size▫ Must check appropriate PPE for

machine▫ Criteria/areas to be investigated by

operant before use.▫ Pre-Work Phase:

Machine set up – dependent on nature of work and material

▫ Work Phase: General procedure to follow when

processing material▫ Post-Work Phase:

Isolation Cleanliness Re-positioning of components (safety)

to standard position▫ ETC…


WT4603

SEE YOU ALL NEXT WEEK!!!

wt4603 unit3 week4

Education