work holding on lathe machine
TRANSCRIPT
![Page 1: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/1.jpg)
Method Of holding work
![Page 2: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/2.jpg)
Method of Holding Work
• There are several method of holding work piece on the lathe machine. This presentation looks on a few of them.
![Page 3: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/3.jpg)
Chucks
![Page 4: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/4.jpg)
![Page 5: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/5.jpg)
Chucks
• Used extensively for holding work for machining operations– Work large or unusual shape
• Most commonly used lathe chucks– Three-jaw universal– Four-jaw independent– Collet chuck
![Page 6: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/6.jpg)
Three-jaw Universal Chuck
• Holds round and hexagonal work• Grasps work quickly and accurate • Three jaws move
simultaneously whenadjusted by chuck Key
![Page 7: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/7.jpg)
Four-Jaw Independent Chuck• Used to hold round, square, hexagonal, and
irregularly shaped workpieces• Has four jaws
– Each can be adjusted independently by chuck Key• Jaws can be reversed to hold work by inside
diameter
![Page 8: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/8.jpg)
Collet Chuck• Collet chuck is used to hold small Collet chuck is used to hold small
workpieces.workpieces.• Used for high-precision work• Spring collets available to hold round, square,
or hexagon-shaped workpieces• Each collet has range of only few thousandths
of an inch over or under size stamped on collet
![Page 9: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/9.jpg)
![Page 10: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/10.jpg)
|
Collet Chuck
Special adapter fitted into taper of headstock spindle, and hollow draw bar having internal thread inserted in opposite end of headstock spindle. It draws collet into tapered adapter causing collet to tighten on workpiece.
![Page 11: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/11.jpg)
![Page 12: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/12.jpg)
Work Held Between Centre
![Page 13: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/13.jpg)
Work Held Between Centres
![Page 14: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/14.jpg)
Face plate• A faceplate is the basic workholding accessory
for a lathe. It is a circular metal plate which fixes to the end of the lathe spindle. The workpiece is then clamped to the faceplate, typically using t-nuts in slots in the faceplate, or less commonly threaded holes in the faceplate itself.
![Page 15: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/15.jpg)
Faceplate• Used to hold work too large or shaped so
it cannot be held in chuck or between centers
• Usually equipped with several slots to permit use of bolts to secure work
![Page 16: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/16.jpg)
Mandrel
• Holds internally machined workpiece between centers so further machining operations are concentric with bore
• Several types, but most common– Plain mandrel– Expanding mandrel– Gang mandrel– Stub mandrel
![Page 17: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/17.jpg)
Plain Mandrel
![Page 18: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/18.jpg)
Expanding Mandrel
![Page 19: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/19.jpg)
Gang Mandrel
![Page 20: Work holding on lathe machine](https://reader033.vdocuments.mx/reader033/viewer/2022052203/58ece5811a28abd0018b471f/html5/thumbnails/20.jpg)
Summary
• The method use is highly based on the:• Shape of metal• Length of metal• Type of operation to perform• Condition of the workpiece