1

Wireless Alarm SystemUser Manual

1. System Components And Usage

Note:1.The alarm system has been programmed already,please operate the system according to the part 2 of the manual;2.If you want to add additional HTZSAFE sensors to the system,please operate the system according to the part 3 of the manual or contact us directly.

contact@saferhomee.com)After-sale Service:E-mail:

Plug-in Alarm Receiver

Power Plug:plug the receiver into a socket

Volume

Melody

Indicator Light

Power Plug

Volume: 4 volume levels adjustableMelody: 35 classic melodies optionalIndicator Light: flash for several seconds when the sensor be activated

Solar Wireless Motion Sensor

Sensor Eye

2

Speaker

Speaker:sound for several seconds when the sensor be activated

Sensor Eye: detect the objects

Solar Panel:charge the built-in battery of the sensor

Solar Panel

Drain Hole:used to drain out the rainwater(please note

the drain hole must be at the bottom when you install

the sensor)

Drain Hole

3

ON/OFFCharge Jack

Charge Jack:used to connect the additional solar panel

or DC 5V power adapter

ON/OFF:turn on/off the sensor

Charge Jack

The KIT inclues a charge cable which is used to chargethe solar wireless motion sensor before use or if long- termcontinuously rainy days caused low battery.Please chargethe sensor for 4 hours as below:

ATTENTION PLEASE

4

2. Operation Instructions

Step 1Plug the receiver into a outlet

Step 2

The indicator light of the receiver will flash for 15 seconds means working properly

Turn on the Wireless Motion Sensor:Press the ON/OFF button 4 times

(bleep prompt means work normally)

ON/OFF( )press 4 times

4

5

(the light of the ON/OFF button will flash once means the motion sensor was activated and sent the alarm signal;and then the motion sensor will back to work mode automatically

after about 10 seconds if not detecting any movements)

1 foot waya

Step 3Activate The Wireless Motion Sensor(wait about 30 seconds after you turned on the sensor)

1st method:press the ON/OFF button twice

(the light of the ON/OFF button will flash once means

the motion sensor was activated and sent the alarm signal)

ON/OFF( twice)press

2nd method: Ensure the sensor is turned away from you.and walk through in front of the sensor to acivate

6

Step 4

total 35 melodies optional.Press “Melody” once to choose the melody for this sensor,

Step 5Same steps for the other sensors

Step 6Installations

Melody

short screws

long screws

Wireless Motion Sensor

1

2

3

2.Please point the sensor towards a open field(not towards the trees or bushes)

3.please adjust the sensor a little down(not upward)

1. Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind.

Installation Notes:

7

3. Other Settings

(1)How to add additional sensors to the receiver(up to 32 sensors can be added to 1 receiver)

Step 1Plug the receiver into a outlet

Step 2Press and hold the “Volume” button for 5 seconds and release the button when you heard a beep prompt and the indicator light flashing;

Volume

light up

press and hold the button for 5 seconds

Volume

flashing slowly

release the button

Volume

8

Step 3

Note:please make the sensor close to the alarm receiverActivate the sensor.

Step 4

has been added to the receiver already.Activate the sensor again to confirm the sensor

Step 5

total 35 melodies optional.

(2)How to delete the sensors of the receiver

Press”Melody”button to choose the melody for this sensor.

Step 1

Plug the receiver into a outlet

Step 2

Press and hold both the “Volume” button and “Melody”

button for 10 seconds and release the

buttons when you heard a long beep prompt;

Note: all the sensors will be deleted by this operation.

(a ring tone prompt and the indicator light flashing quickly means the sensor has been added to the wireless alarm

receiver successfully)

flashing quickly

Volume

Melody

(the indicator light flashing 3 times means the sensor was activated properly)

9

ON/OFF( twice)press

Step 1

Plug the receiver into a outlet

Step 2

Press the “Volume” once to adjust the volume of the receiver.

(total 4 volume levels adjustable)

(4)How to change the melody for the sensors

(total 35 melodies optional,match different

melody with different sensor)

Step 1

Plug the receiver into a outlet

Step 2

Activate the sensor first,and then press the “Melody” button

to choose the melody for this sensor

Same steps for other sensors which have been added to

the receiver already.

Volume

(3)How to adjust the alarm volume

(5)How to adjust the sensitivity of the sensor

The sensor has 3 sensitivities adjustable (High, Middle, Low)

Step 1 turn off the sensor by press the ON/OFF button 3 times

10

11

4. Technical Parameters

Plug-in Alarm Receiver

Technical parameters

Static Current 20mA; Alarming Current 300mAWorking Current

AC 110V-220V

433MHz FSK+FHSS

Technical Parameters

Working Voltage

Wireless Frequency

Item

80mm 48mm

86mm

34mm

Step 2If select Low sensitivity---turn on the sensor by pressing the ON/OFF button 3 timesIf select Middle sensitivity---turn on the sensor by pressing the ON/OFF button 4 timesIf select High sensitivity---turn on the sensor by pressing the ON/OFF button 5 times

103mm

92mm

Wireless Motion Sensor

45mm 90mm

Technical parameters

433MHz FSK+FHSS

Chargeable LiFePO4 Battery

3.3V

50 feet(15m)

Technical Parameters

500mAh

Static: 1mA; Alarming:60mA

≥100mA in Sunny days

1/4 Mile(400m)

-22°F to 158°F(-30℃ to 70℃)

15

Detection Range

Item

Wireless Transmission Range

Wireless Frequency

Working Voltage

Battery Type

Battery Capacity

Working Current

Solar Panel Output Current

Working Temperature Range

Detection Angle

12

After-sale Service:E-mail:contact@saferhomee.com)