williams products, inc.williamsproducts.net/s/williams products catalog.pdf · williams products,...
TRANSCRIPT
Williams Products, Inc. 1750 Maplelawn Drive
Troy, MI 48084 Phone: 248-643-6400
Fax: 248-643-7117
A Worldwide supplier of Construction Seal and Gasket Material
The Williams Product line, Everlastic®, covers a wide variety of "Job Tested" products specifically designed and manufactured to fulfill a required function. They are widely specified by the
Architect/Engineer and used by the concerned contractor. Williams Products are listed with the Construction Specification Institute.
Comprehensive stocks of all items are carried at all times. Assuring you, in most cases, shipment within 24 hours of the receipt of an order.
This catalogue offers technical information for our products and addresses applications based on the needs of the architect. Please feel free to contact us for any additional information you may need,
catalogues, copies of technical data or material samples.
To the best of our knowledge this published information is accurate, however, to determine suitability of material/product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any
loss or damage resulting from inappropriate usage.
Contents
1. DIVISION 3 CONCRETE A. Bearing Pads
a. AASHTO Grade Neoprene ‐ Conforms to AASHTO requirements, 2500 PSI tensile strength b. 1200 Series ‐ Commercial Grade Dense Neoprene c. Bear‐Pad 200 ‐ Cross Laminated with oriented fibers d. Fab‐Pad 300 ‐ Multiple layers of high quality, cotton polyester duck fabric, MIL C 882 E e. Everlastic® Post Pads ‐ For isolation, vibration dampening and sealing under mounting posts or base plate f. Everlastic® Iso/Vib 2300 Series Foam ‐ Vibration and shock absorbency, resists creep under load
B. Rubber Waterstop a. SBR/Neoprene Waterstop b. Waterstop Fittings c. Waterstop Installation d. Waterstop Splicing Instructions e. Williams #37 A Adhesive
C. Column Isolation a. Column Boxboard ‐ Coated Corrugated b. Econ‐O‐Foam ‐ CCPE c. EJ‐2000 ‐ XL Polyolifin
D. Rubber "J" Gate Seals a. Hi Tensile Neoprene Williams Compound # 1025. Also available in other rubber compounds to meet custom specifications
E. Expansion Joints a. Econ‐O‐Foam ‐ CCPE b. EJ‐2000 ‐ XL Polyolefin c. 1040 to 1080 Series ‐ Closed Cell Neoprene d. NN‐1 ‐ Soft, Expanded, Closed Cell, Sponge Rubber e. NN‐5‐2C5 ‐ Closed Cell Expanded Neoprene Foam f. 1056 Joint Filler g. NN‐1, NN‐3, NN‐5 h. Everlastic® 1752 Rebonded Rubber Type IV i. 1300 Series ‐ Concrete Gray Sponge Rubber j. 1400 Series ‐ Open Cell Neoprene (Vibration Isolation) k. Everlastic® 1752 Highway Modified ‐ Isomeric Polyolefin Resilient Flexible Gray Foam l. Everlastic® Expand‐O‐Foam – 900 ‐ Closed Cell Polyethylene Foam, ASTM D‐3575 & ASTM D‐1056 (Modified) m. Vinyl “U” 1000 Series n. Concrete Panel Seals
2. DIVISION 4 MASONRY A. Masonry Control Joints
a. Masonry Control Joints : Slot Seal Standard, Wide Flange, Block Seal ‐ Hard rubber cross shape, shear keys in sash blocks, Weathertite‐R, Everlastic® M‐CJ ‐ Compressible Filler to seal Michigan Control Joints
B. CMU Expansion Joint (Horizontal) ‐ Fill gap at top of wall a. Expand‐O‐Foam b. EVA 200G ‐ Air Seal Gasket c. 1056 Joint Filler d. NN‐1 1040 Series
C. Cavity Wall Baffle a. Everlastic® Cavity Wall Baffle using EVA 200 ‐ Compartmentalization of the cavity wall system will equalize the negative pressure within the
wall cavity to the exterior positive pressure more quickly and efficiently when using PVC brick vents, cell vents or open head joints b. Williams‐Goodco Brick Vents ‐ Ventilates and equalizes pressure within cavity. Sizes, 2 ‐ 1/4", 2 ‐ 3/4", 3 ‐ 5/8". Colors, Standard Gray. We can
dye to match mortar color c. Williams‐Goodco CMU Vents
D. Closures: Close off gap between wall and deck (flat or fluted) a. Metal Deck Closure b. Partition Closure c. Typical Partition/Deck Closure Installation Details
E. Fire Rated a. Dyna Shield Ceramic Fiber Joint Filler
F. Fire Classified a. Everlastic® Fire Classified Closures 1715 ‐ Fire Classified Closure manufactured of Compressible Open Cell Sponge. Used for Partition
closure or plug for Metal Decking
G. Anchor Gaskets a. Self‐stick, CC Neoprene ‐ Thermal and moisture break behind anchors
H. Brick Expansion Joints a. Neo Seal IV ‐ Neoprene profile allows maximum movement b. Column Boxboard c. Econ‐O‐Foam ‐ Filler is inherent bond breaker for most sealants
I. Adhesives a. Williams #37 A Contact Adhesive b. Williams #37 B c. Williams #37 C – Low VOC
3. DIVISION 7 THERMAL AND MOISTURE PROTECTION CUSTOM DESIGNS A. 2nd Seal B. Wide Joint Seal C. Closure / Partition Wall D. Closure / Metal Deck Flutes E. Closure / Everlastic® 1715 Fire Classified F. Backer Rod and Joint Fillers
a. Neoprene Backer Rods b. Standard Closed Cell Polyethylene Backer Rod (CCPE) c. Hot Rod d. Tundra Foam e. Soft Type
G. Roof Expansion Joint: NN‐1 1040 Series H. Everlastic® Cavity Wall Baffle using EVA 200 I. EVA 400 J. Dust Shield 1350 Series
4. SEALANTS A. Sealant Color Chart
DIVISION 3 CONCRETE
Bearing Pads
Rubber Waterstop Rubber “J” Gate Seal
Expansion Joints
Bearing Pads
AASHTO Grade Neoprene 1200 Series Commercial Grade
Bear-Pad BP-200 Fab-Pad FP-300
Post Pads Iso/Vib 2300 Series
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/02 www.williamsproducts.net
TECH DATA Description: Bridge Bearing contain only virgin crystallization resistance Polychloroprene (Neoprene) raw polymer Use: As economical efficient bearing plates for pre-cast, pre-stressed concrete or steel beams in bridges and buildings. Neoprene Pads permit a smooth and uniform transfer of load from the beam to the substructure, allow beam rotation at the bearing due to deflection of the beam under load. They further allow lateral and longitudinal movement of the beam caused by thermal forces. Neoprene Pads have no moveable parts and thermal expansion and contraction are absorbed by the pad’s ability to give and take in shear. There is no sliding between pad and beam or between pad and abutment.
Material Property
ASTM Standard
Test Requirements
Polychoroprene 50 Duro 60 Duro 70 Duro Units
Physical Properties
D2240 Hardness Min Tensile Strength Min Ultimate Elongation
50 ±5 2250* 400
60 ±5 2250* 350
70 ±5 2250* 300
ShoreA Pt psi (Mpa) %
Heat Resistence
D573 at spec. temp
Specified Temp of Test Aging Time Max Change in Duro Hardness Max Change in Tensile Strength Max Change in Ultimate Elongation
212 (100) 70 +15 -15 -40
212 (100) 70 +15 -15 -40
212 (100) 70 +15 -15 -40
°F (°C) Hours *Shore Pt % %
Compression Set
D395 Method B at Spec. Temp
Specified Temp of Test Degrees Max Permissible Test (after 22 Hours)
212 (100) 35
212 (100) 35
212 (100) 35
°F (°C) %
Bar Resistance D624 Min Pounds Per Inch (Die C) 180 180 180 Pounds/In
Brittleness Ozone Resistance
D2137 D1149
Low Temp Brittleness at -40°F (-40°C) Partial Presser of Ozone During Test Duration of Test Tested at 20% Strain 100°F ±2°F (37.7°C ±1°C) Mounting Pressure
Pass 50 100 No Cracks
Pass 50 100 No Cracks
Pass 50 100 No Cracks
Mpa Hours
Shear Modulous
At 23°C .62-.90 89.90-135
.90-1.40 135-203
1.40-2.05 203-297.25
Mpa PSI
Note: Williams Bearing Pads conforms to grade 3 as follows: LOW TEMPERATURE BRITTLENESS: D-746, procedure B, @ -40°F, resulting in no failures, 50, 60, and 70 ±5% Shore A Durometer. INSTANTANEOUS THERMAL STIFFENING: D-1043, grade 3, tested @ -40°F. LOW TEMPERATURE CRYSTALLIZATION: Grade 3, 14 days, @ -15°F. Stiffness at test temperature shall not exceed 4 times the stiffness measured at 73°F. * Higher tensile strength available upon request
WILLIAMS AASHTO GRADE NEOPRENE BEARING PADS
SPECIFICATION M251-06
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Dense Rubber • Color: Black
• Meets ASTM-D 2000 Available Sizes • Cut Parts, Rolls & Sheets - CUT TO SIZE • Cut to Thickness, Width & Length • Sheet & Roll Sizes vary – call for specific limits • Available in variable hardness Applications • Bearing Pads • Vibration Isolation Pads • Rustification & Chamfer Strips • Setting Blocks • Spacers
Typical Physical Properties
Property Test Method Typical Values Durometer Hardness ASTM D - 2240 60 ± 5, Shore A Ultimate Tensile ASTM D - 412 1000 psi., min. Ultimate Elongation ASTM D - 412 300% min. Ozone Resistance (20% Strain 100 hours @ 104° F)
ASTM D - 1149 No Cracks
Low Temperature Flexibility (5 hours @ -40°F)
ASTM D - 2137 Pass
Aged in Air (70 hrs @ 158°F) Change in Hardness Change in Tensile Change in Elongation
ASTM D – 573
± 15 pts. max. ± 30% max. -50% max. change (not less than 300%)
Compression Set (22 hrs. @ 158° F)
ASTM D -395 Method B 20% max.
Williams Everlastic® 1200 Series
Commercial Grade Dense Neoprene
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Durable Rubber Compound integrated with cross-ply high strength synthetic fibers, resulting in an
R.O.F Integral Bearing Pad with excellent physical properties and weather resistance. Features • Durable dense rubber with excellent compressive strength, hardness, tear resistance and cold weather
flexibility. “Green Product” molded from masticated rubber using discarded tires. Available Sizes • Thickness from ¼” to 1” • Width and Length up to 48” • Available in cut parts and profiles Applications • Bearing Pads, Shims, Bumpers, Vibration Isolation
Typical Physical Properties Property Test Method Typical Values
Hardness (Shore A) ASTM D - 2240 75 ± 5 duro Tensile Strength – Mpa (psi) Min – With Grain Min – Cross Grain
ASTM D - 412, Die C 7.0 (1015) 3.0 (435)
Compression Maximum Strength Initial Cracking Strain
10,000 psi 40%
Elongation - % Min – With Grain Min – Cross Grain
ASTM D - 412, Die C 15 45
Tear Strength – kN/m (pi) Min –With Grain Min – Cross Grain
ASTM D - 624, Die B 35 (200) 70 (400)
Heat Aging change in tensile - % Max change in elongation - % Max change in hardness – Shore A
ASTM D – 573 After Exposure for 70 Hours @ 70ºC
+/- 25 +/- 25 +/- 10
Oil Swell (increase in volume) ASTM D - 471 120% max. Ozone Resistance kN/m (pi) Min Cross-Grain Tear Strength
ASTM D - 518 After Exposure to 80pphm for 50 hours @ 38ºC
53 (300)
Low Temperature Brittleness Not Brittle at -40ºC
ASTM D - 2137 Pass
Everlastic® Bear Pad BP - 200
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/02 www.williamsproducts.net
TECH DATA Description • Bearing pads constructed of multiple layers of cotton duck fabric saturated with Neoprene. Specifications • AASHTO 18.10.2
• MIL - C - 882-E Features • Outstanding Compression Strength. Superior resistance to Oil, Ozone, Sunlight, Heat, Water,
Steam and Fungus. Applications • Bearing Pads under extreme loads to reduce shock and vibration and to disperse the load.
Typical Physical Properties
Property Typical Values
Density 67 lbs./cu.ft min. Hardness (Shore A) 90 ± 5 Plies per inch 64
Typical Load Deflection - ½” Thick (32 ply)
50 PSI - 0.005 400 PSI - 0.020 800 PSI - 0.032 1400 PSI - 0.047 100 PSI - 0.008 500 PSI - 0.023 900 PSI - 0.034 1600 PSI - 0.052 200 PSI - 0.013 600 PSI - 0.026 1000 PSI - 0.037 1800 PSI - 0.057 300 PSI - 0.017 700 PSI - 0.029 1200 PSI - 0.042 2000 PSI - 0.062
Typical Permanent Set
Compressive Stress Permanent Set %
500 0.85 % 1000 1.6 % 3000 3.5 % 5000 5.1 %
10,000 8.9 %
Everlastic® Fab-Pad FP - 300
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Applications: For isolation, vibration dampening, and sealing under mounting posts or base. Available in the following load bearing pads: Bear Pad BP-200 Masticated Rubber with synthetic fabric (green product)
Commercial Grade Dense Neoprene ASTM D-2000, BC 610
AASHTO Grade Dense Neoprene 50. 60, and 70 Durometer M-251-06
Everlastic Fab Pad AASHTO 18.10.2, MIL-C-882-E
Also available in Closed Cell Foam
Williams Everlastic® Post Pads
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description: Everlsatic Iso/Vib (isolation vibration) 2300 Series is a closed cell polyethylene foam that is a flexible, lightweight, durable, solid extruded plank. Ideally suited as a shock absorbing, vibration dampening, isolating and cushioning material. Features: Offers excellent strength, vibration, and shock absorbency, resistance to creep under load, and water resistance characteristics. Everlastic 2300 Series is impervious to most chemicals, non-abrasive, and preforms consistently over a wide range of temperatures. Uses: Where equipment foundations require vibration containment, foundations for press pits, or any concrete slab that requires isolation or vibration dampening (see detail below). Color: Black Available Sizes: • Standard thickness ½” to 4” thick, 48” wide, and 108” long. • Available with self-stick, pressure sensitive adhesive (PSA) on one or two sides. Typical Physical Properties Unit Test Method Typical Results Density ln/ft3 ASTM D-3575 2 to 2.4 Tear Strength lb/in ASTM D-3575 13 Compression Creep psi ASTM D-3575 <5% @ 3.0 Compression Strength 25% Deflection psi ASTM D-3575 10.5 50% deflection psi ASTM D-3575 19
Compression Set (loaded @ 1.5 psi 1000hrs @ 50%)
% ASTM D-3575 18 Tensile Strength (@1/2" thickness) psi ASTM D-3575 42 Water Absorption (lbs SF of cut surface) ASTM D-1056 <0.2 Thermal Conductivity (BTU-in/hr/sf°F) at 75°F ASTM C518 0.4 - 0.18 Thermal Stability (change after 24hrs at 165°F) % ASTM D-3575 <5
Everlastic Iso/Vib 2300 Series Foam
Rubber Waterstop
SBR/Neoprene Waterstop
Waterstop Fittings Waterstop Installation
Waterstop Splicing Instructions 37 “A” Adhesive
TECH DATA Everlastic® SBR /Neoprene Rubber Waterstop
3/8" 1. PRODUCT NAME: 3/4" Williams SBR Hi-Tensile Rubber Waterstop,
6" Williams Neoprene Hi-Tensile Waterstop.
3/8" 2. MANUFACTURER: 3/4" Williams Products, Inc.
9" 1750 Maplelawn Troy, Mi. 48084
3/8" ph. (248) 643-64003/4" Toll Free (800) 521-9594
12" Fax. (248) 643-7117
Centerbulb (CB) 3. PRODUCT DESCRIPTION:1-1/8" O.D. 3/4" I.D. 1-1/2" O.D. 3/4" I.D. Basic Use: " A Waterstop is usually a section of flexible waterproof
1/4" 3/8" material placed at any joint in concrete to prevent the passage of water".5/8" Williams Products, Inc. has been a pioneer supplier to constructors
1" with the Williams Everlastic® Waterstop System since 1954. 6" 9" Joints in concrete structure, on one side of which is subject to
hydrostatic load, are generally Williams Spec. Williams provided with waterstops bridging2010 Hi-Tensile Specification joints and embedded in concrete
(SBR) 1025 on either side. In concrete joints Styrene Hi-Tensile where expansion and contraction
Physical Property ASTM test Method Butadiene Neoprene cause the joints to close and open,Tensile Strength, min (PSI) ASTM D412 2500* 2500* the waterstop must be designed to Ultimate Elongation, Min (%) ASTM D412 450 450 accommodate itself to movement.Hardness, Shore A durometer ASTM D2240 65 +/- 5% 65 +/- 5% The primary reason for specifyingTensile Stress min PSI to Rubber Waterstops rather thanproduce 300% elongation ASTM D412 1150 1150 metal or PVC is their superior per-Water Absorption, max % by formance in withstanding shear weight after immersion 7 days ASTM D471 5 5 movements and to resisting hydrostaticat 73.4 degrees F +/- 2 F pressure. Compression Set, Max % after ASTM D395 Rubber Waterstops will elongate22 hours at 158 digress F Method B 30 30 over four times original size Tensile Strength after aging, Min (ASTM D 412) and will continue% of original after 7 days in air returning to near original shape afterat 158 degrees +/- 2 degrees F, ASTM D572 80 80 repeated movement. They have veryand 300 PSI low compression set and perform Specific Gravity ASTM D1817 1.17 +/- .03 1.17 +/- .03 well at low temperatures.Ozone cracking resistance after The Williams System features20% elongation for 7 days 0.5 p/m ASTM D1149 no cracks no cracks sleeve type fittings that provide fastat 38 degrees C (neoprene 3 p/m) positive splicing and precise Water-Tensile set, % max after 200% stop alignment. Fittings are manufac-elongation for 10 min at 23 ASTM D412 5 5 tured form the same elastomers/poly-degrees +/- 1 degree C mers as the waterstop.* 3000 PSI from actual part / Test Sheets.
TYPICAL INSTALLATIONS INCLUDE: Sewer plants, water filtration plants, aqueducts, reservoirs, aqueducts, reservoirs, locks, tanks, channels, swimming pools, culvertstunnels, underpasses, Bridge decks and abutments, roofs, dams, foundations, mine shafts, retaining walls and any concrete structurerequiring watertight joints.LIMITATIONS: The Dumbell Waterstop is adequate for all vertical and horizontal stress across the joint in the same plane as the waterstop. 6"Dumbell Waterstop is adequate for all vertical and horizontal construction joints. 6" Dumbell is also used on expansion joints up to 1". 9" and 12" Dumbell is used in expansion joints of 1" to 2". 6" Centerbulb is used in expansion joints up to 1" where shear movement is expected and 9" Centerbulb is used in expansion joints up to 2" where shear movement is expected. The Centerbulb is hollow so it can deform to absorb shear movements. Split Waterstops are used for short straight runs only. When Split Waterstops are spread against forms, connecting unionscannot be used.
TECH DATA Everlastic® Waterstop Fittings
UNION VERTICAL ELL VERTICAL TEE HORIZONTAL CROSS
FLAT ELL HORIZONTAL TEE REDUCER
FITTINGS SELECTION TABLE STANDARD STOCK ITEMS
SIZE Type 6" DB 9" DB 12" DB 6" CB 9" CB 12" CB Union 6DB-U 9DB-U 12DB-U 6CB-U 9CB-U 12CB-U Vertical Ell 6DB-VE 9DB-VE 12DB-VE 6CB-VE 9CB-VE 12CB-VE Vertical Tee 6DB-VT 9DB-VT 12DB-VT 6CB-VT 9CB-VT 12CB-VT Flat Ell 6DB-FE 9DB-FE 12DB-FE 6CB-FE 9CB-FE 12CB-FE Flat Tee 6DB-FT 9DB-FT 12DB-FT 6CB-FT 9CB-FT 12CB-FT Flat Cross 6DB-FC 9DB-FC 12DB-FC 6CB-FC 9CB-FC 12CB-FC
Williams Everlastic® Waterstop Fittings are a sleeve type design for easy and efficientinstallation. The illustrations shown are commonly used fittings for common waterstop installation. For unusual waterstop transitions, custom fittings are available, contact William Products for availability and price. The fittings are glued to waterstop for waterproof connections using the Williams Everlastic® No. 37 A Adhesive (see installation instructions).All fittings are available for dumbell and centerbulb waterstops and in SBR or Neoprene compounds.
™ To the best of our knowledge this published information is accurate, however, to determine suitability of material/product WILLIAMS for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss or damage PRODUCTS, INC. resulting from inappropriate usage.
WILLIAMS PRODUCTS, INC. - 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - FAX (248) 643-7117
page 3-07 www.williamsproducts.net
TECH DATA WATERSTOP INSTALLATION PAGE 1
Sealing Expansion Joints in Water Reservoir Wall and Base Slabs with Center bulb Waterstop. Pre-Sealing Plane of Sealing Joint Between two
Weakness in Foundation Wall Floor Slab Members with Dumbell Waterstop. with Dumbell Waterstop.
PLACEMENT OF WATESTOP:
Waterstop shall be cut square, then joined with Williams Efficiency Fittings and Williams No. 37 Adhesive per instructions.
Installation of Waterstop shown involves split forms. The Waterstop is placed in position that one bulb will be embedded in each of two adjoining slabs or walls.The Waterstop shall be held firmly in place with a block or other suitable
Sealing Joint between Roof Slab arrangements on the outside of the split form (away from the concrete which is toand wall of Digester in a Sewage be placed). Treatment Plant with DumbellWaterstop. After the concrete has setup, the split form and block may be removed. When
the adjoining placement is made, care should be taken to support the water stop.
Waterstops are not ridged enough to resist the weight of concrete being placed and must be supported to maintain the proper position. It is easy to supply necessary support by using bulb rings and wire to fasten the water stopto steel rerod. After the water stop is positioned in a split form, wooden blocks should be nailed to one side of the form, as shown below. End bulb rings should be clamped into the bulb of the water stop as shown below. Rings should be embedded in the bulb only to avoid puncturing the web. Rings and tie wires should be place12 to 18 inches apart.
wood split form steel re rod or re barend bulb ring pliers
waterstopend bulb ring
back block wire ties
To the best of our knowledge this published information is accurate, however, to determine suitability of material/product ™ for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss or damage WILLIAMS resulting from inappropriate usage. PRODUCTS, INC.
WILLIAMS PRODUCTS, INC. - 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - FAX (248) 643-7117
page 4-07 www.williamsproducts.net
TECH DATA WATERSTOP INSTALLATION PAGE 2
tie wiresend bulb rings
DO'S AND DON'TS FOR INSTALLATION
DO: Sweep all horizontal joints prior to waterstop placement to insure that foreign material
doesn't interfere with the direct contact between waterstop and concrete.
steel re rod DO: Systematically and thoroughly vibrate concrete around waterstop to avoid voids in concrete and insure complete contact with the waterstop.
DO: Hold waterstop in place to prevent VERTICAL WATERSTOP SET UP misalignment during placement of
concrete.
DO: Take care during second placement to insure that the waterstop is not deformed by the impact of concrete placement.
DO NOT: Drive nails through waterstop.
DO NOT: Embed Center Bulb in concrete. It must be centered in the expansion joint. (see page one Expansion Joints)
FIRST PLACEMENT DO NOT: Embed Bulb Rings into the web of the waterstop when tying to steel rerod.
SECOND PLACEMENT
To the best of our knowledge this published information is accurate, however, to determine suitability of material/product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss or damage
™ resulting from inappropriate usage. WILLIAMS
PRODUCTS, INC.
WILLIAMS PRODUCTS, INC. - 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - FAX (248) 643-7117
page 5-07 www.williamsproducts.net
TECH DATA Waterstop Splicing Instructions
MATERIALS REQUIRED Union
Square Stirring SticksSharp razor knife Paint brushesSandpaper or wire brush Blocks of woodSolvent "C" clamps
"C" clamps WaterstopWoodBlock
Waterstop
"C" ClampsWaterstop and Wood
BlocksUnion
Waterstop - Union Clamping Detail
Horizontal TeeDIRECTIONS Horizontal Tee - Waterstop Clamping Detail 1. Cutting Waterstop: Determine proper length. Use square to mark 90° cutting line. Cut waterstop with sharp razor knife.
2. Waterstop and fitting surface preparation: Sand with medium sand paper or wire brush surfaces which will be glued, to remove mold release of other contaminants and to increase surface area. Remove sandy dust by wiping surfaces with MEK (Methyl ethyl ketone) or other suitable solvent.
3. Adhesive Application: Stir No. 37A adhesive well before using. Brush inside fitting and allow to dry (usually about 5 minutes). Brush No. 37A adhesive on water stop then insert into fitting using wet adhesive on waterstop as a lubricant. When inserting waterstop be sure square cut end of waterstop makes full contact with base of fitting sleeve (THIS IS IMPORTANT TO INSURE MAXIMUM ADHESION).
4. Adhesive drying and curing: To obtain maximum adhesion and prevent movement in the splice joint as work progresses, use wood blocks and "C" clamps to hold firmly in place. Drying time will vary with temperature and humidity. Pressure can usually be removed and joint gently handled within 30 minutes at temperature of 65°F or more. Normally 60% to 70% of optimum strength will be obtained within 24 hours. As the temperature goes down, the adhesive becomes progressively higher in viscosity. This is completely reversible with stirring and increasing temperature. At low Temperatures, the drying time and buildup of strength are greatly extended. Depending on temperature, optimum strength may take anywhere from three days to four weeks.
To the best of our knowledge this published information is accurate, however, to determine suitability of material/product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss or damage
WILLIAMS resulting from inappropriate usage. PRODUCTS, INC.
WILLIAMS PRODUCTS, INC. - 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - FAX (248) 643-7117
page 6-07 www.williamsproducts.net
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/05 www.williamsproducts.net
TECH DATA Description A high strength, synthetic based adhesive Cream in color Well suited for bonding cellular rubber to its self as well as vinyl, concrete, metal, and wood. Material Specifications ASTM E 84 Packaging Quart and gallon containers. Preparation of Stock Surfaces to be bonded should be free of excess dust, grease, moisture and other contaminants. Metal surfaces should be degreased with a suitable solvent. Application Instructions Thoroughly clean both surfaces to be bonded with recommended cleaner. Surfaces must be free of moisture to insure proper adhesion. Apply one thin, uniform coat of adhesive to both surfaces to be bonded. Allow the adhesive to become tacky to touch. Join with sufficient pressure to insure contact. Best used at room temperature 72°F. Approximate optimum service temperature range 40°F to 90°F. The adhesive should be used directly from storage. Cleaner and Thinner: Thin with Toulene Clean up can be done with Toulene or MEK Precautionary Data: This product is extremely flammable. Vapors may cause flash fires. Vapors may ignite explosively under certain conditions. Keep away from fire, sparks, and sources of heat. Open all doors and windows. Extinguish all flames and pilot lights. Turn off electric motors, stoves, or heaters, or any source of ignition during use and until all vapors have been dispersed. Do not smoke. Close containers after use. Review MSDS Sheet for handling before use. FLASH POINT: Less than 0°F AVOID PROLONGED BREATHING OF VAPORS AVOID PROLONGED AND REPEATED CONTACT WITH SKIN KEEP OUT OF REACH OF CHILDREN STORE AT TEMPERATURES OF 90°F OR BELOW FOR MAXIMUM SHELF LIFE USE WITH ADEQUATE VENTILATION INFORMATION PHONE Out of State: 800-521-9594 In State: 248-643-6400 Chemtel: 1-800-255-3924
Williams Everlastic® #37 “A” Adhesive
Column Isolation
Column Boxboard
Econ-O-Foam EJ-2000
TECH DATA Everlastic® Column Boxboard
COLUMN BOXBOARD IS CONSTRUCTED FROM 100% RECYCLED PAPER.
COLUMN BOXBOARD
column
5002-3 5008-3 5004-3
block
1/4" 1/2" 1/4"
ROLLS SHEETS brick 48" X 250' 48" X 48"
COLUMN BOXBOARD Neo Seal (Nominal sizes)
COLUMN BOXBOARD
The Column Boxboard material is used as a isolation material between the structural column and the masonry wall construction. This separation is necessary to prevent the masonry from coming in contact with the column during loading and prevent mortar from being within the same joint. Thisproduct is a cellulose material coated on the weathering side and can be factory scored or scored in the field for bending or breaking to fit any column shape. The nominal thickness of the roll product 1/4"while the sheet product is available at either 1/4" or 1/2" nominal thickness and each being 48" square.
INSTALLATION:
The Column Boxboard material is installed prior to the erection of the masonry wall to assure isolation between the structural column and the masonry wall.
To the best of our knowledge this published information is accurate, however, to determine suitability of material/ ™ product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss WILLIAMS or damage resulting from inappropriate usage. PRODUCTS, INC.
WILLIAMS PRODUCTS, INC. 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - TOLL FREE (800) 521-9594 - FAX (248) 643-7117
www.williamsproducts.net
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
♦ Expanded, closed cell, plank, polyethylene foam. Economical, lightweight, flexible, compressible, resilient, non-absorbent, inherent bond breaker.
Typical Properties Test Procedure Results
Properties and Characteristics
Density (PCF) ASTM D 3575 Test C 1.3-1.5 nominal
1. Compressive Strengths: Econ-o-Foam is available in a variety of compressive strengths, and can supports a wide range of loads. 2. Weights: Econ-O-Foam is available in densities ranging from 1.5 to 2.2 lbs/cu ft 3. Chemical Resistance: Econ-O-Foam offers excellant stability when exposed to most acides, hydrocarbons, chlorinated solvents, petroleum products, apints, warnishes, thinners, and alcohols 4. Tempurature Range: Econ-O-Foam polyethylene foam has been used successfully in tempuratures ranging from -40°F tp 160°F without significant effect on many of its properties. 5. Water Absorption: Econ-O-Foam polyethylene is virtually impermeable. The amount of water absorbed is negligible even when used in flotation applications. Econ-O-Foam also offers high resistance to transmission of water vapors, with ratings of less than .1 per inch. It contains no water soluble sonstituents. 6. Availability: Econ-O-Foam is available in cut strips. pads, and trimmed or mill run sheets. Rolls are stocked in 1/4", 3/8", and 1/2" thicknesses by 48" wide and 50'0" long.
Cell Size (MM) ASTM D 3576 Dow Modified 1.3
Compression Strength ASTM D 7576 Test B 5% 10% 25% 50%
3.5 5 8 15
Compression Creep ASTM D 3575 Test BB Loaded @ specified PSI static load for 1000hrs 75°F 160°F
5 @ 1.5 psi 5 @ .25 psi
Tensile Strength (psi) ASTM D 3575 Test E 50 Tensile Elongation (%)
ASTM D 3575 Test E 60
Tear Stength (lb/in) ASTM D 3575 Test D 15 Flexural Modulous (psi)
ASTM D 790 300
Bouyancy (PFC) ASTM D 3575 Test AA 55-60
Thermal Conductivity (B1U-in/hr ft °
ASTM D 3575 Test EE Method B 0.4
Thermal Stability (% shrinkage)
ASTM D 3575 Test F Conditioned @ specified temp. with no load 24hrs 48hrs
-1.0 @ 165°F -2.4 @ 165°F
Everlastic® Econ-O-Foam
1390 Series
TECH DATA Everlastic® EJ - 2000
Everlastic® EJ - 2000 with PSA
Scoredcolumn Tear - Tab
block
Concrete brick Slab
Everlastic® EJ-2000
Neo- Seal IVDescription • Everlastic® EJ-2000 is a cross linked closed cell foam. • Gray in color.
Applications • Expansion joint filler with hot or cold applied sealants, pipe and thermal wrap, acoustica partition closures, corrugated deck closures, column isolation wrap, and other uses.
Available Sizes • Standard thickness 3/8" and 1/2". Other sizes skived or laminated. • Standard rolls are 60" x 50'-0". • Available multi score, standard score and tear tab to allow sealant reservoir. • Available with self-stick, pressure sensitive adhesive (PSA) on one or two sides. • Die cut parts Available.
Typical Physical Properties Test Method Typical ResultsDensity: lb/ft³ ASTM D- 3575 2Tear resistance pi ASTM D- 3575 10Compression Deflection 10% defection ASTM D- 3575 2.6 psi
25% defection 5.6 psi40% defection 9.2 psi50% defection 13.5 psi
Compression Set (22 hrs @50%) ASTM D- 3575 99%Elongation % ASTM D- 3575 135Tensile Strength psi ASTM D- 3575 37 Water Absorption (lb/sf of cut surface) % ASTM D-1056 < 0.07K Factor ASTM C -177 0.25
To the best of our knowledge this published information is accurate, however, to determine suitability of material/ ™ product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss WILLIAMS or damage resulting from inappropriate usage. PRODUCTS, INC.
WILLIAMS PRODUCTS, INC. 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - TOLL FREE (800) 521-9594 - FAX (248) 643-7117
www.williamsproducts.netpage 25-07
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Material Specifications
• Hi Tensile Neoprene Williams Compound # 1025, also available in other rubber compounds Tolerances:
• Width +/- 3/16” • Diameter of bulb +/- 1/16” • Length: 20’0”
Available Sizes: • 1-3/4” dia. Solid bulb or hollow bulb 4” wide • For custom configurations contact Williams Products
Uses: • Low head gate where conditions are favorable to using the water pressure to aid in sealing • Flat, vertical lift gates, bulkheads, stop locks
Typical Physical Properties
Property Typical Values Tensile Strength 2250 min. PSI Ultimate Elongation 400% min. Shore A Durometer 60/70 Specific Gravity 1.4 Compression Set 30% max. Tensile Strength after Oxygen Bomb Aging 80% min. Ozone Resistance Good All “J” Seals set forth in these specifications, and shown on the drawings, shall be of an extruded neoprene rubber with a SOLID or HOLLOW BULB, and typically 4” wide, as manufactured by Williams Products, Inc. For custom profiles, and other rubber compounds of “J” Seals, contact Williams Products.
Everlastic® Rubber “J” (Gate Seals)
1-3/4” O.D. ¾” I.D.
9/16”
Standard Rubber “J” (Gate Seal)
4”
Expansion Joints
Econ-O-Foam EJ-2000
1040 to 1080 Series NN-1 1040 Series
NN-5 2C5 E1 1056 Joint Filler
NN-1/NN-3/NN-5 1752 Rebonded Rubber Type IV
1300 Series Concrete Gray 1400 Series
1752 Highway Modified Expand-O-Foam
Vinyl “U” 1000 Series Panel Seals
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
♦ Expanded, closed cell, plank, polyethylene foam. Economical, lightweight, flexible, compressible, resilient, non-absorbent, inherent bond breaker.
Typical Properties Test Procedure Results
Properties and Characteristics
Density (PCF) ASTM D 3575 Test C 1.3-1.5 nominal
1. Compressive Strengths: Econ-o-Foam is available in a variety of compressive strengths, and can supports a wide range of loads. 2. Weights: Econ-O-Foam is available in densities ranging from 1.5 to 2.2 lbs/cu ft 3. Chemical Resistance: Econ-O-Foam offers excellant stability when exposed to most acides, hydrocarbons, chlorinated solvents, petroleum products, apints, warnishes, thinners, and alcohols 4. Tempurature Range: Econ-O-Foam polyethylene foam has been used successfully in tempuratures ranging from -40°F tp 160°F without significant effect on many of its properties. 5. Water Absorption: Econ-O-Foam polyethylene is virtually impermeable. The amount of water absorbed is negligible even when used in flotation applications. Econ-O-Foam also offers high resistance to transmission of water vapors, with ratings of less than .1 per inch. It contains no water soluble sonstituents. 6. Availability: Econ-O-Foam is available in cut strips. pads, and trimmed or mill run sheets. Rolls are stocked in 1/4", 3/8", and 1/2" thicknesses by 48" wide and 50'0" long.
Cell Size (MM) ASTM D 3576 Dow Modified 1.3
Compression Strength ASTM D 7576 Test B 5% 10% 25% 50%
3.5 5 8 15
Compression Creep ASTM D 3575 Test BB Loaded @ specified PSI static load for 1000hrs 75°F 160°F
5 @ 1.5 psi 5 @ .25 psi
Tensile Strength (psi) ASTM D 3575 Test E 50 Tensile Elongation (%)
ASTM D 3575 Test E 60
Tear Stength (lb/in) ASTM D 3575 Test D 15 Flexural Modulous (psi)
ASTM D 790 300
Bouyancy (PFC) ASTM D 3575 Test AA 55-60
Thermal Conductivity (B1U-in/hr ft °
ASTM D 3575 Test EE Method B 0.4
Thermal Stability (% shrinkage)
ASTM D 3575 Test F Conditioned @ specified temp. with no load 24hrs 48hrs
-1.0 @ 165°F -2.4 @ 165°F
Everlastic® Econ-O-Foam
1390 Series
TECH DATA Everlastic® EJ - 2000
Everlastic® EJ - 2000 with PSA
Scoredcolumn Tear - Tab
block
Concrete brick Slab
Everlastic® EJ-2000
Neo- Seal IVDescription • Everlastic® EJ-2000 is a cross linked closed cell foam. • Gray in color.
Applications • Expansion joint filler with hot or cold applied sealants, pipe and thermal wrap, acoustica partition closures, corrugated deck closures, column isolation wrap, and other uses.
Available Sizes • Standard thickness 3/8" and 1/2". Other sizes skived or laminated. • Standard rolls are 60" x 50'-0". • Available multi score, standard score and tear tab to allow sealant reservoir. • Available with self-stick, pressure sensitive adhesive (PSA) on one or two sides. • Die cut parts Available.
Typical Physical Properties Test Method Typical ResultsDensity: lb/ft³ ASTM D- 3575 2Tear resistance pi ASTM D- 3575 10Compression Deflection 10% defection ASTM D- 3575 2.6 psi
25% defection 5.6 psi40% defection 9.2 psi50% defection 13.5 psi
Compression Set (22 hrs @50%) ASTM D- 3575 99%Elongation % ASTM D- 3575 135Tensile Strength psi ASTM D- 3575 37 Water Absorption (lb/sf of cut surface) % ASTM D-1056 < 0.07K Factor ASTM C -177 0.25
To the best of our knowledge this published information is accurate, however, to determine suitability of material/ ™ product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss WILLIAMS or damage resulting from inappropriate usage. PRODUCTS, INC.
WILLIAMS PRODUCTS, INC. 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - TOLL FREE (800) 521-9594 - FAX (248) 643-7117
www.williamsproducts.netpage 25-07
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Closed Cell Expanded Neoprene Rubber • Black in color • Excellent physical properties including; abrasion, low temperature, and resistance to petroleum base
fluids. Typical Physical Properties
Product Designation 1040 NN-1
1050 NN-2
1060 NN-3
1070 NN-4
1080 NN-5
ASTM Designation: D 1056 D 1056 D 1056
SCE - 41 RE - 41
2C1
SCE - 42 RE - 42
2C2
SCE - 43 RE - 43
2C3
SCE - 44 RE - 44
2C4
SCE - 45 RE - 45
2C5 MIL R - 6130 C Type / Grade Condition
II - A Soft
II - A Soft -
Medium
II - A Medium
II - A Medium -
Firm
II -A Firm
Physical Properties: Color Black
(Gray) Black (Gray)
Black (Gray)
Black (Gray)
Black
Compression - Deflection 25% defl. (psi.) (kN/m2 )
2 - 5 (14 - 35)
5 - 9 (35 - 63)
9 - 13 (63 - 91)
13 - 17 (91 - 119)
17 - 25 (119 - 168)
Ultimate Tensile Strength 75 psi. 100 psi. 100 psi. 150 psi. 150 psi. Elongation: Typical Properties % 175 % 175 % 200 % 150 % 125 % Density: lb/ft3 6 ± 2
.10 ± 03 7 ± 2
.11 ± 03 10 ± 2
.16 ± 03 20 ± 4
.32 ± 06 24 ± 6
.12 ± 02 Fluid Immersion: 7 days @ 73° F Ref. Fuel B, weight change max. %
5 %
5 %
5 %
5 %
5 %
Accelerated Aging: 7 days @ 73° F Flexibility: 180 ° bend without cracking Change in compression -deflection
Pass ± 20%
Pass ± 20%
Pass ± 20%
Pass ± 20%
Pass ± 20%
Maximum Weight % 5 5 5 5 5 Odor No
objectionable odor
No objectionable
odor
No objectionable
odor
No objectionable
odor
No objectionable
odor Service Temperature Low High Continous High Intermittent
-40°F 200°F 250°F
-40°F 200°F 250°F
-40°F 200°F 250°F
-40°F 200°F 250°F
-40°F 200°F 250°F
This Material is Made in the U.S.A Certified
Resistance To: Acid Excellent Flame Resistance: FMVSS.302, U.L. 94 HF - 1 Alkali Excellent Refers to Suffix Letter “M” Gasoline & Oil Good Mil. R-6130C Aromatic Hydrocarbons Fair MVSS - 305 Self-Extinguishing Ketones Fair Chlorinated Solvents Poor 2C1-2C5 refers to oil resistance (medium swell) Oxidation Excellent Ozone Excellent
Williams Everlastic® Closed Cell Neoprene Types
NN-1, NN-2, NN-3, NN-4, NN-5
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
• Everlastic® NN-1 is a soft, expanded, closed-cell, sponge rubber. • Blend of Neoprene, EPDM, and SBR.
Material Specifications • ASTM D - 1056 - 2A1/2C1 • ASTM D – 6576 II A/B Condition Soft
Applications • Expansion joint filler in masonry and concrete. • Filler support sealant in traffic bearing joints. • Other applications that require a firm, economical and durable gasket.
Available sizes and packaging • Available in sheets, strips or cut parts. • Standard bun size: 2” x 42” x 72” • Available with self-stick, pressure sensitive adhesive (PSA) one or two sides. • Cut to thickness, width and length. • Larger dimensions factory spliced or bonded as needed.
Typical Physical Properties Property Test Method Typical Values
Polymer Base Na CR/EPDM/SBR Color Na Black Density –LBS per cubic foot ASTM D - 3575 6 ± 2 Compression/Deflection @ 25% Defl. ASTM D - 1056 2 to 5 psi. Elongation (Die A) ASTM D - 412 150 % Ultimate Tensile Strength (Die A) ASTM D - 412 75 psi. Water Absorption maximum increase in weight
ASTM D - 1056 5% max.
Accelerated Aging – 7 days @ 158ºF Flexibility (180º bend without cracking) Change in appearance Change in Compression Deflection
ASTM D - 1056
Pass None ±30%
Service Temperature (F°) Low High Continuous High Intermittent
ASTM D - 746
-40ºF 200ºF 250ºF
K Factor – BTU/hr. (sf) ºF inch Na 0.30
Flame Resistance FM VSS - 302 Pass This Material is Made in the U.S.A Certified
Resistance To: Acid Excellent Flame Resistance: FMVSS.302, U.L. 94 HF - 1 Alkali Excellent Refers to Suffix Letter “M” Gasoline & Oil Good Mil. R-6130C Aromatic Hydrocarbons Fair MVSS – 302 Ketones Fair Self-Extinguishing Chlorinated Solvents Poor 2C1 refers to oil resistance (medium swell) Oxidation Excellent Ozone Excellent
Everlastic® NN -1
1040 Series
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Closed Cell Expanded Neoprene Foam (CR based) • Stable physical properties Material Specifications • ASTM D1056: 2C5 • SAE Designation: 2C5 • ASTM D6576: Type II A Firm Available Sizes • Available in sheets, strips, or cut parts (sheet size: 1” x 40” x 48) • Available with self-stick, pressure sensitive adhesive (PSA) on one or two sides • Cut to thickness, width, and length • Large dimensions factory spliced or bonded as needed Applications • Used above or below grade where good weather and/or resistance to petroleum based fluids (medium
swell). • To isolate dissimilar substrates. • Expansion joint filler.
Typical Physical Properties Property Test Method Typical Values
Density ASTM D1056 24 ± 6 lb./ft³ Hardness Durometer Shore 00 ASTM D2240 70 ± 5 Compression Deflection 25% psi
kPa ASTM D1056 21 ± 4
145 ± 28 Compression Set % ASTM D1056 ?25 % Tear Strength lb/in
kN/m ASTM D624 (Die C) 35
6.1 Tensile Strength psi
kPa ASTM D412 (Die A) 150
1030 Elongation % ASTM D412 (Die A) 175 Resilience ASTM D2632 15 Water Absorption (maximum weight change %) ASTM D - 1056 < 5% Service Temperature (F°) Low
High Continuous High Intermittent
ASTM D746 -40 150 200
Fluid Immersion [7 days @ 23°C (73.4°F)] ASTM Ref Fuel B Weight Change %
ASTM D1056
<150
Accelerated Aging [7 days @ 70°C (158°F)] Flexibility: 180° bend without cracking
Appearance Change Change in Compression Deflection %
ASTM D1056 Pass None ± 30
Combustion Characteristics FMVSS - 302 Pass
Williams Everlastic® NN-5 2C5
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Closed Cell Expanded Rubber Flame-Retarded NBR Nitrile
• Color: Black
• Excellent physical properties including abrasion and low temperature resistance. Poor resistance to petroleum based fluids.
Material Specifications • ASTM D – 1056-2C1 • ASTM D - 1056-RE41E1 • ASTM D - 1056-SCE41 Available Sizes • Rolls, Sheets – Cut to Size: thickness: 1/4" - 1", widths up to 48" • Available with pressure sensitive temporary positioning adhesive. • Use with Williams No. 37 “A” Adhesive for permanent bonding. Shipping Weight • lb. Per 1” x 12” x 12”
Applications • Expansion Joint Filler in Masonry. • Isolation between dislike substrates.
Typical Physical Properties Property Test Method Typical Values
Density ASTM D - 1667 3.5 - 5.0 p.c.f Compression Deflection 25% ASTM D - 1056 1.5 - 3.0 psi. Compression Set 25% ASTM D - 1667 25 max % Compression Set 50% (Sample size 1” x 2” x 2”)
ASTM D - 1056 (ASTM D - 1667*)
50 max % (15 max %*)
Tensile ASTM D - 412 40 min. psi. Elongation ASTM D - 412 100 min % Water Absorption ASTM D - 1056 5 max % Water Absorption ASTM D - 1667 0.1 max lbs/sq.ft. Heat Aging ASTM D - 1056 +/- 30 % Thermal Stability ASTM D - 548
(% change in length after 7 days @ 220F)
10 max wt %
Ozone Resistance ASTM D - 1171 Pass Operating Temperature Range -297°F(-183°C) to 220°F(104°C)
Williams Everlastic® 1056 Joint Filler
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Closed Cell Expanded Neoprene Rubber
• Black in color
• Excellent physical properties including abrasion and low temperature resistance. Fair resistance to petroleum based fluids.
Typical Physical Properties Series 1040 1060 1080
Products Designation NN-1 NN-3 NN-5
Physical Properties Test Method 2A1-2C1 2A3-2C3 2A5-2C5 Density (lb/cu. Ft) ASTM D-1056 6 ±2 9 ± 2 19 ± 4 Hardness (Durometer Shore 00) ASTM D-2240 45 ± 5 60 ± 5 70 ± 5 Compression Deflection: 25% psi kPa
ASTM D-1056 3.5 ±1.5 24 ±10
11 ± 2 76 ± 14
21 ± 4 145 ± 28
Compression Set (%) ASTM D-1056 < 40 < 30 < 25 Tensile Strength psi kPa
ASTM D-412 (Die A) 75
520 100 690
150 1030
Tear Strength lb/in kN/m
ASTM D-624 (Die C) 9.6 1.7 125
12 3.2
35 6.1
Elongation (%) ASTM D-412 (Die A) 125 125 275 Resilience ASTM D-2632 35 25 15 Service Tempurature Low °F High Continuous °F High Intermitttent °F
ASTM D-746 (-)40 200 250
(-)40 200 250
(-)40 200 250
Water Absorption (max. weight change %) ASTM D-1056 < 5 < 5 < 5 Fluid Immersion 7 days @ 23°C (73.4°F) ASTM Ref. Fuel B, weight change max %
ASTM D-1056 Not
Applicable Not
Applicable < 150 Accelerated Aging: 7 days @ 70°C (158°F) 180° bend without craacking Appearance Change Chang in Compression Deflection
ASTM D-1056 Pass None ± 30%
Pass None
± 30 %
Pass None
± 30 % Combustion Charateristics FMVSS-302
UL 94HF-1 Pass Pass
Pass Pass
Pass Pass
This Material is Made in the U.S.A Certified
Resistance To: Acid Excellent Flame Resistance: FMVSS.302, U.L. 94 HF - 1 Alkali Excellent Refers to Suffix Letter “M” Gasoline & Oil Good Mil. R-6130C Aromatic Hydrocarbons Fair MVSS - 305 Self-Extinguishing Ketones Fair Chlorinated Solvents Poor 2C1-2C5 refers to oil resistance (medium swell) Oxidation Excellent Ozone Excellent
Williams Everlastic® Closed Cell Neoprene Types NN-1, NN-3, & NN-5
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 11/03 www.williamsproducts.net
TECH DATA Description:
Pre-molded sponge rubber made from recycled rubber. Black in color Blend of Neoprene, EPDM, and SBR
Material Specifications: ASTM D 1752 AASHTO M-153
Available Sheet Size: Standard Sheet size is 1" x 42" x 60" Thickness: ¼", 3/8", ½", ¾", and 1" May be laminated to other thicknesses Widths: Cut to order, minimum ½"; maximum 42"
Availability: Typically shipped from shelf stock, cut to order.
Applications: Expansion joint filler material in a variety of construction joints, particularly in concrete cast – in
– place applications.
Physical Properties Chart Density (minimum) ASTM D-1752 30pcf Compression Set ASTM Method: 1/2" samples
compressed 50% for 22 hrs. @ 70 degrees – 24 hr recovery
5% maximum
Recovery ASTM D-1752 95%+ Compression Deflection (50%) ASTM D-1752 50-1500 Temperature Resistance
Low High Continuous High Intermittant
ASTM D-1752 -40 degrees F +180 degrees F +220 degrees F
Accelerated Aging (7 days at 158°F – Lineal shrinkage maximum 2%) 114 Flexibility
ASTM D-1752 Good 180° bend without cracking
Water Absorption by weight ASTM D-1752 Average of closed- celled and open-celled sponge
Tensile Strength ASTM D -1752 25 psi Elongation ASTM D -1752 75%
Williams Everlastic® 1752 Rebonded Rubber
Type IV
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Preformed, chemically blown, sponge rubber comprised of all virgin polymer and containing no
reclaim rubber or factice. Material Specifications • ASTM D - 1752 - Type 1 Sponge Rubber • Federal: HH - F - 341f Type II, Class A • AASHTO - M - 153 - Type 1 Available Roll Sizes • Thickness: ¼” x 36” x 60 LF; 3/8” x 36” x 60 LF; ½” x 36” x 45 LF; ¾” x 36” x 30 LF; 1” x 36” x
24 LF • May be laminated to other thickness • Widths: Cut to order, Minimum ½”; Maximum 36” Availability • Typically shipped from shelf stock, cut to order.
Applications • Expansion joint filler material in a variety of construction joints, particularly in concrete cast - in -
place applications. • Where concrete is poured on an incline or decline plan or thicker concrete pours where lateral loads
at the base require a firmer joint treatment.
Typical Physical Properties
Property Test Method Typical Values
Density ASTM D - 1564 30 lbs/ cubic foot Compression Deflection 50% ASTM D - 1752 70 psi. Recovery ASTM D - 1752 98 % Weathering ASTM D - 545 Pass Extrusion ASTM D - 1752 .10 %
Williams Everlastic® 1300 Series
Concrete Gray Sponge Rubber Joint Filler
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Black Neoprene Sponge Rubber with a interlinking cell structure for increased compressibility and
outstanding resiliency. Material Specifications • ASTM D - 1056 Grade SCO - 11 • ASTM D - 1056 Grade 1C1 • SAEJ - 18R Grade SCO - 11 • MIL - C - 3133 - C Grade SCO - 3 • MIL - STD - 670 - B Grade SCO - 3 Available Roll Sizes • ¼” x 36” x 90 LF; 3/8” x 36” x 36 LF; ½” x 36” x 36 LF; 1” x 36” x 30 LF• Material may be slit, die cut or saw to any size needed. Uses • Structural Isolation, Vibration Damping, Press Pit Lining, Sealant Back Up, and many more
Typical Physical Properties Property Typical Values
Density 25 to 40 lbs/cu. Ft. Compression Deflection 25%
2 to 5 psi.
Compression Set 50% (50% deflection 22 hrs @158° F)
50% max
Tensile 60 psi. min (.125” thick specimen) Elongation 300% min (.125”thick specimen) Durometer 2 to 7 Shore “A” Hardness Aged Compression Deflection ± 20% change from original (7 days @ 158°F) Resilience Factor (Bayshore Method)
30 to 40% Rebound (.50 thick at room temperature)
Williams Everlastic® 1400 Series
Open Cell Sponge Neoprene Joint Filler
Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 2/02 www.williamsproducts.net
TECH DATA Description Isomeric Polyolefin Resilient Flexible Foam
Gray in color Applications Everlastic 1752 Highway/Modified Expansion Joint Filler used with hot or cold applied sealants;
Horizontal applications, place Everlastic 1752 Highway/Modified next to forms; all interrupting columns and objects; adjacent to abutting structures prior to concrete placement. Vertical applications include Everlastic 1752 Highway Modified placement between panels, panel to column joints, or in block wall joints prior to sealing. And many other uses.
Available Sizes Standard Thickness: 1/8" – 3” (Other sizes Skived or Laminated). Widths from 1/2" to 60"; Available Multi-Score, Standard-Score, or with tear tab to allow sealant
reservoir (available in rolls only 1/8”-1/2”). Self-Stick Pressure Sensitive Adhesive (PSA) optional. (Will Die Cut Parts) Roll (1/8”-1/2”) lengths: 50 LF Sheet (5/8”-3”) lengths: 9 LF Everlastic1752 Highway/Modified must be held in place by either compression or sealant to reduce
float. Typical Physical Properties
Property Test Method Typical Values Density (Nominal) ASTM D - 3575 2 PCF Tear Resistance CM ASTM D - 3575 11 PI Compression Strength
10% Deflection 25% Deflection
40% Deflection 50% Deflection
2.6 psi 5 psi 9.6 psi 15 psi
Compression Set % of Original Thickness
ASTM D - 3575 25%
Elongation ASTM D - 3575 120% Tensile Strength CM ASTM D - 3575 40 PSI Water Absorption (lb./sf of cut surface)
ASTM D - 3575
<0.07
K Factor ASTM C - 177 0.25 Service Temperature Low High
PPP C - 1752
-65°F +210°F
Thermal Stability (Change after 24 hrs. @ 158°F)
ASTM D - 3575 2%
Williams Everlastic® 1752 Highway/Modified
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
• Expanded, closed cell, plank, polyethylene foam. Economical, lightweight, flexible, compressible, resilient, non-absorbent, inherent bond breaker.
Material Specifications
• ASTM D 1056 ASTM D 3575
Applications • Concrete expansion joint filler for use with cold applied sealants.
Place Expand-O-Foam against existing formed concrete; place subsequent concrete directly to it. • Pipe isolation, thermal wrap. • Acoustical partition closures. • Corrugated deck closures. • Masonry expansion joints and column isolation. • Many other uses.
Available sizes and packaging
• Standard thickness: 5/8" to 4". • Widths from 1/2" to 48". • Will cut to custom size and/or profile. • Self-stick pressure sensitive adhesive optional.
Typical Physical Properties
Property Test Method Typical Values Density ASTM D 1622 2.0 lb./ft3 (32.04 kg/m3) Compression Strength 10% deflection 80% deflection
ASTM D 3575 ASTM D 3575
10 psi (69 KPa) max 125 psi (862.49 KPa) max
Tensile Strength ASTM D 3575 55 psi (379.50 KPa) Water absorption ASTM D 3575 0.5% vol. max Temperature Stability ( N/A -40° F to 160° F (-40° C to 71° C)
Everlastic® Expand-O-Foam
1380 Series
Concrete Slabs
Williams Everlsatic® 1380 Series Expand-O-Foam
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/02 www.williamsproducts.net
TECH DATA Description • Closed Cell Expanded Polyvinyl Chloride
• Off White (Natural) Color
• Good Chemical Resistance & temperature serviceability. • Good tensile Material Specifications • ASTM D - 1667 Grade VE41 • ASTM D - 1056 SBE41 & SCE41 • ASTM D - 1056 RE41E1 Available Sizes • ROLLS, SHEETS - CUT TO SIZE • Available with pressure sensitive temporary adhesive. • Use with Williams No. 37 “A” Adhesive for permanent bonding. Uses • Isolation: Steel from masonry • Metal from metal (curtain walls etc.)
Typical Physical Properties Property Test Method Typical Values
Density ASTM D - 1667 8.0 Compression Resistance 25% ASTM D - 1056 1.5 - 3.0 psi. Comp. Set 25% ASTM D - 1056 24% max. Comp. Set 50% (Sample size 1” x 2” x 2”)
ASTM D - 1056 (ASTM D - 1667*)
50% max.. (15% max*)
Tensile ASTM D - 412 40 min. Elongation ASTM D - 412 100 % min. Water Absorption ASTM D - 1056 10 % max wt. Heat Aging ASTM D - 1056
(22 hrs. @ 158°F +/- 30 %
Thermal Stability ASTM D - 548 (% change in length after 7 days @ 220F)
7 % max wt.
Ozone Resistance ASTM D - 1171 Pass Temperature Use (Lower limit to upper limit)
- 40F to 220F
Williams Everlastic® Vinyl Type U 1000 Series
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
• Everlsatic Precast Concrete/Metal Panel Seals provide a permanent pressure contact seal at all time, with a minimum of pressure, when placed between panel joints. This type of design provides the architect complete control over joint system.
• The various panel types are designed, with regard to size and functional characteristics, to provide an effective seal for both vertical and horizontal joints under virtually any condition that might arise in either precast concrete or metal panel construction.
• The unusual flexibility in adaptation provided by the design of Everlastic Seals, whether used singly or in combination, will effectively seal panel joints up to one inch in width; with each type readily able to compensate for variations in joint width, irregular joint surfaces and the inevitable reaction adjustments to overall building dimensions.
Technical Data • All the technical data for each seal satisfies the ASTM material standards. If details are required, contact the
technical staff at Williams Products, Inc. Installation
• The Everlastic Panel Seals should be factory installed by the panel manufacturer while joint faces are clean. These seals should be selected on the basis of the seal being compressed at least 25% and not more than 50% in the joint width specified. The seal should be placed in the joint the proper depth to accommodate sealant placement with baker rod. Horizontal seals should be protected during shipment at the bottom side of the panel to prevent destroying seals. Panel seals should be stored in a dry location in unopened cartons prior to installation. All Everlastic Panel Seals can be furnished with pressure sensitive adhesive on one side which will hold the seal in place during installation.
Everlastic® Concrete Panel Seals
DIVISION 4 MASONRY
Masonry Control Joints
CMU Expansion Joint (Horizontal) Cavity Wall Baffle
Closures Fire Rated
Fire Classified Anchor Gaskets
Brick Expansion Joints Adhesives
TECH DATA Everlastic® Masonry Control Joints
SLOTSEAL STD 2015-3 BLOCK SEAL 2018-3 WEATHERTITE "R" 0318-3 mortar
bond breaker 3/8" 11/16"
2-5/8" 5/8" 1/2" 2-11/16" 1"
1"
1-5/8" 1-5/8" 1/2"
APPLICATIONSEverlastic® Masonry Control materials are designed to prevent destructive cracking in masonry and prevent destructive cracking in masonry (from temperature and drying shrinkage, differential movement ofstructural members and surrounding masonry, settling of foundations, etc.). Williams' materials also seal out moisture and cold air at a reasonable price.
SLOT SEAL STANDARD 2015-3A shear lug to provide shear control and vertical control for expansion/contraction of masonry walls. Manufactured of high grade synthetic rubber compounds.Polymer: Blended EPDM/SBR/CR, AASHTO D-2000, 3BA810-80 Shore A Hardness, 1000 PSI tensile.Exceeds material standards of 2AA805 (80 hardness - 500 PSI tensile).
BLOCK SEAL 2018-3For Sash BlockHollow wings are easily compressed to provide pressure seals on each side of keyway in additionto shear control. Manufactured of high grade synthetic rubber compounds.Polymer: Blended EPDM/SBR/CR, ASTM D-2000, 3BA810-80 Shore A hardness, 1000 PSI tensile.Exceeds material standards of 2AA805 (80 hardness - 500 PSI tensile).
WEATHERTITE "R" 0318-3For Stretcher or Line Block (Michigan Control Joints)A specially shaped, non-absorbent, expanded rubber strip seal. Weathertite "R" provides multiple, continuous, presser sealing surfaces. This closed cell material is impervious to water and possess high acoustical insulatingproperties.Polymer: Neoprene grade ASTM D-1056, RE 41, SCE-41, 2A1.
™ To the best of our this published information is accurate, however, to determine suitability of material/ Williams product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss Products or damage resulting from inappropriate usage.
WILLIAMS PRODUCTS, INC. 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - TOLL FREE (800) 521-9594 - FAX (248) 643-7117
www.williamsproducts.net38-07
CMU Expansion Joint
Expand-O-Foam
EVA 200G 1056 Joint Filler
NN-1 1040 Series
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
• Expanded, closed cell, plank, polyethylene foam. Economical, lightweight, flexible, compressible, resilient, non-absorbent, inherent bond breaker.
Material Specifications
• ASTM D 1056 ASTM D 3575
Applications • Concrete expansion joint filler for use with cold applied sealants.
Place Expand-O-Foam against existing formed concrete; place subsequent concrete directly to it. • Pipe isolation, thermal wrap. • Acoustical partition closures. • Corrugated deck closures. • Masonry expansion joints and column isolation. • Many other uses.
Available sizes and packaging
• Standard thickness: 5/8" to 4". • Widths from 1/2" to 48". • Will cut to custom size and/or profile. • Self-stick pressure sensitive adhesive optional.
Typical Physical Properties
Property Test Method Typical Values Density ASTM D 3575 2 to 2.4 pcf Tear Resistance (@ 1/2" thickness) ASTM D 3575 13 pi Compressive Creep ASTM D 3575 <5% @ 3.0psi Compression Strength 25% deflection 50% deflection
ASTM D 3575 ASTM D 3575
10.5psi 19psi
Compression set (Loaded @ 1.5psi1000 hrs @ 50%)
ASTM D 3575 18%
Tensile Strength (@ 1/2" thickness) ASTM D 3575 42psi Water absorption (lb/sf of cut surface) ASTM D 3575 <0.2 Thermal Conductivity (BTU-in/hr ft² °F) at 75ºF
ASTM C518 0.4 – 0.48
Thermal stability (change after 24 hrs at 165ºF
ASTM D 3575 <5%
Everlastic® Expand-O-Foam
1380 Series
revised 1-1-12
www.williamsproducts.net
Description:
Plugs and strips for metal decks
WT --- is the width at the top of the closure. WB --- is the width at the bottom of the closure. H --- is the height from top to bottom of the plug. D --- is the thickness or distance into the flute. V --- is distance between closure plugs at the base. T --- is the thickness of the closure strip.
Closure
WBD
H
T - of runner
Strip Closure
WB
V
H
D
WT
WT
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description Closed Cell Expanded Rubber
Black in color
Excellent physical properties including abrasion and low temperature resistance. Poor resistance to Petroleum based fluids.
Material Specifications ASTM D – 1056-2CI ASTM D - 1056-RE41E1 ASTM D - 1056-SCE41 Available Sizes ROLLS, SHEETS - CUT TO SIZE Available with pressure sensitive temporary positioning adhesive. Use with Williams No. 37 “A” Adhesive for permanent bonding. Shipping Weight lb. Per 1” x 12” x 12”
Applications Expansion Joint Filler in Masonry. Isolation between dislike substrates.
Typical Physical Properties Property Test Method Typical Values
Density ASTM D - 1667 3.5 - 5.0 p.c.f Compression Deflection 25% ASTM D - 1056 1.5 - 3.0 psi. Comp. Set 25% ASTM D - 1667 25 max % Comp. Set 50% (Sample size 1” x 2” x 2”)
ASTM D - 1056 (ASTM D - 1667*)
50 max % (15 max %*)
Tensile ASTM D - 412 40 min. psi. Elongation ASTM D - 412 100 min % Water Absorption ASTM D - 1056 5 max % Water Absorption ASTM D - 1667 0.1 max lbs/sq.ft. Heat Aging ASTM D - 1056 +/- 30 % Thermal Stability ASTM D - 548
(% change in length after 7 days @ 220F)
10 max wt %
Ozone Resistance ASTM D - 1171 Pass Temperature Use Lower limit to upper limit
- 40F to 220F
Williams Everlastic® 1056 Joint Filler
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
• Everlastic® NN-1 is a soft, expanded, closed-cell, sponge rubber. • Blend of Neoprene, EPDM, and SBR.
Material Specifications • ASTM D - 1056 - 2A1/2C1 • ASTM D – 6576 II A/B Condition Soft
Applications • Expansion joint filler in masonry and concrete. • Filler support sealant in traffic bearing joints. • Other applications that require a firm, economical and durable gasket.
Available sizes and packaging • Available in sheets, strips or cut parts. • Standard bun size: 2” x 42” x 72” • Available with self-stick, pressure sensitive adhesive (PSA) one or two sides. • Cut to thickness, width and length. • Larger dimensions factory spliced or bonded as needed.
Typical Physical Properties Property Test Method Typical Values
Polymer Base Na CR/EPDM/SBR Color Na Black Density –LBS per cubic foot ASTM D - 3575 6 ± 2 Compression/Deflection @ 25% Defl. ASTM D - 1056 2 to 5 psi. Elongation (Die A) ASTM D - 412 150 % Ultimate Tensile Strength (Die A) ASTM D - 412 75 psi. Water Absorption maximum increase in weight
ASTM D - 1056 5% max.
Accelerated Aging – 7 days @ 158ºF Flexibility (180º bend without cracking) Change in appearance Change in Compression Deflection
ASTM D - 1056
Pass None ±30%
Service Temperature (F°) Low High Continuous High Intermittent
ASTM D - 746
-40ºF 200ºF 250ºF
K Factor – BTU/hr. (sf) ºF inch Na 0.30
Flame Resistance FM VSS - 302 Pass This Material is Made in the U.S.A Certified
Resistance To: Acid Excellent Flame Resistance: FMVSS.302, U.L. 94 HF - 1 Alkali Excellent Refers to Suffix Letter “M” Gasoline & Oil Good Mil. R-6130C Aromatic Hydrocarbons Fair MVSS – 302 Ketones Fair Self-Extinguishing Chlorinated Solvents Poor 2C1 refers to oil resistance (medium swell) Oxidation Excellent Ozone Excellent
Everlastic® NN -1
1040 Series
Cavity Wall Baffle
Cavity Wall Baffle using EVA 200
Brick Vents CMU Vents
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products Discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage Arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning The possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Material Specifications
Black in color Cross-Linked, Closed Cell, Ethylene/Vinyl Acetate Foam Lightweight, Flexible, Resilient, Non-Absorbent Foam Resistant to Heat, Ultraviolet, Acids, Alkalis, Gasoline & Oil, Aromatic Hydrocarbons, Ketones,
Oxidation and Ozone Uses As a Hot or Cold Applied Sealant Backup To fill Vertical and Horizontal Joints Acoustical Partition Closures Corrugated Deck Closures, and many other uses Available Sizes 1/8” thru 4” thickness May be laminated to other thickness’ Cut to order: widths: ½” - 60”, lengths up to 6'0"
Typical Physical Properties Property Test Method Typical Values
Density (lbs. /cu. Ft.) ASTM D 3575 2.3 ± 0.5 Compression / Deflection (psi Required to compress to 25%)
ASTM D 1056 5 ± 2
Compression Recovery @ 50% Extrusion @ 50%
ASTM D 1752 Modified (10 psi. Min. to 25 psi. Max.)
14.5 psi. 99%*
0.10 inch** Ultimate Tensile Strength ASTM D 3575 50 psi. Water Absorption ASTM D 1056 <5% (max. gain by weight) Odor No Objectionable Odor K Factor 0.25 Service Temperature Low High Continuous High Intermittent
-70° F 180° F 290° F
Flame Resistance MVSS-302 PASS Accelerated Aging (7 Days) 158° Flexibility 180° Bend Without Cracking Appearance Change in Compression/Deflection
Pass None ± 30
After Removal of Load, material shall recover to 95% of original thickness within 24 hours. ** When compressed to 50% of original thickness with three sides restrained; the unrestrained edge shall not extrude
more than 0.25 inches.
Williams Everlastic® EVA 200G
page 36-07
revised 1-1-12
page 37-07
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products Discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage Arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning The possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/02 www.williamsproducts.net
TECH DATAWilliams Goodco CMU VentDescription: The Williams Goodco CMU vent is an injection molded vent made from
flexible polyvinyl chloride in an offset "T" shape. When inserted in vertical mortar jointsbetween two bricks the slotted leg of the vent allows air to pass in and out allows water toweep out and prevents water from penetrating in.Spacing of CMU Vents: Tests indicate thatfor interior/exterior air pressure equalization and for ventilation one Williams Goodco CMUVent to every 10 square feet of wall surface is acceptable. One per 100 square feet is aminimal number. For drainage of condensation and moisture the vents act as weepholes andshould be placed directly on top of the thru wall flashing. One vent for every 24 inches ofhorizontal flashing is acceptable to provide weephole drainage. The vents are hardlynoticeable after installation but a regular symmetrical spacing pattern gives the bestappearance. Functions: When rain contacts an exterior surface water can enter openingsthrough any combination of the following actions: momentum of raindrops, capillary action,gravity and air currents. Cracks, joints between wall components, surface pores andinadequately bonded interfaces may provide the openings for water penetration throughwalls. Much of the water penetration through brick cavity walls is caused not by the drivingwind and rain on the exterior face but by the suction created within the air cavity by thelower interior air pressure. This force is controlled by installing brick vents in sufficientfrequency and size to allow almost immediate air pressure equalization. Since winds gust,rather than create steady pressure, vents must have enough opening area to allow acontinuous exchange of air. Small tubes and wicks have generally proved inadequate becauseof their limited opening size and because they clog quickly.Efflorescence: Efflorescence isreduced by minimizing rain wetting within the exterior wall. However, more absorptive CMUproducts will hold moisture from exterior rain, or condensation on the back face resultingfrom air leakage from the building interior, and under certain environmental conditions(particularly in late Fall) this presence of moisture can trigger efflorescence.
Glazes, Paints or Silicones:When these materials are used, cavity walls are necessary to avoid serious problems. In most buildings, moisture laden
air will leak from the building interior and unless some free passage is available to the outside, spelling, ice lensing or blistering can occur.
Test Reports: Tests have been conducted to determine the rates of air flow through the Williams Goodco CMU vent and to indicate acceptable spacing
for exterior walls. The test procedures and results are published and available on request.
Material Specifications: The Williams Goodco CMU vent is manufactured from a polyvinyl chloride compound specifically designed for continuous
exposure to weathering. This compound possesses excellent sunlight resistance, good low temperature properties and contains a polymeric plasticizer toensure permanence. Physical Properties as determined on molded specimens by ASTM procedures:
Packaging: 100 vents per carton.Color: Light gray. Special Colors Available.Sizes: 7 5/8", 11 5/8", will fabricate special sizes
Short Form Specification:Williams Goodco CMU vents as supplied by Williams Products, Inc. shall be installed in the vertical mortar joints in the
exterior masonry brick wall...(a) As detailed on the drawings.(b) Directly above all through wall flashings at (spacing).(c) Throughout the wall in every (i.e. 4th mortar joint) horizontally and every (i.e. 10th course) vertically.
Features:(1) Top flap overlaps two adjacent Blocks to stop mortar from falling into the air passage.(2) Flexible Wings to adjust to variation in mortar joint widths (5/16" 3/4").(3) Louvers to allow air passages while creating a water barrier.(4) Water ridges when water buildup on the exterior wall surface is blown into the air passage these ridges create a barrier which directs the rain downand out of the cavity
Note*: Provide adequate opening for immediate air pressure equalization, Acts as weeper, Provide neat, attractive appearance, Install easily,
Impede passage of insects, din and rodents, Block entrance to rain, Resist clogging and the corrosive effects of masonry mortars.
Williams-GoodcoCMU Vents Weep System
Closures
Metal Deck Closure Partition Closure
Installation Details
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products Discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage Arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning The possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Material Specifications
Black in color Cross-Linked, Closed Cell, Ethylene/Vinyl Acetate Foam Lightweight, Flexible, Resilient, Non-Absorbent Foam Resistant to Heat, Ultraviolet, Acids, Alkalis, Gasoline & Oil, Aromatic Hydrocarbons, Ketones,
Oxidation and Ozone Uses As a Hot or Cold Applied Sealant Backup To fill Vertical and Horizontal Joints Acoustical Partition Closures Corrugated Deck Closures, and many other uses Available Sizes 1/8” thru 4” thickness May be laminated to other thickness’ Widths: cut to order, Minimum ½” , Maximum 48”
Typical Physical Properties Property Test Method Typical Values
Density (lbs. /cu. Ft.) ASTM D 3575 2.3 ± 0.5 Compression / Deflection (psi Required to compress to 25%)
ASTM D 1056 5 ± 2
Compression Recovery @ 50% Extrusion @ 50%
ASTM D 1752 Modified (10 psi. Min. to 25 psi. Max.)
14.5 psi. 99%*
0.10 inch** Ultimate Tensile Strength ASTM D 3575 50 psi. Water Absorption ASTM D 1056 <5% (max. gain by weight) Odor No Objectionable Odor K Factor 0.25 Service Temperature Low High Continuous High Intermittent
-70° F 180° F 290° F
Flame Resistance MVSS-302 PASS Accelerated Aging (7 Days) 158° Flexibility 180° Bend Without Cracking Appearance Change in Compression/Deflection
Pass None ± 30
After Removal of Load, material shall recover to 95% of original thickness within 24 hours. ** When compressed to 50% of original thickness with three sides restrained; the unrestrained edge shall not extrude
more than 0.25 inches.
Williams Everlastic® EVA 200G
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
Everlastic® EPDM Sponge is expanded, closed-cell, Ethylene Propylene Diene sponge rubber. Non-absorbent, compressible, resilient, provides good thermal and moisture installation Everlastic® EPDM Sponge is generally resistant to acids, alkali, oxidation and ozone. Everlastic® EPDM Sponge is not recommended in applications that require oil resistance.
Material Specifications ASTM D - 1056 - 2A1 ASTM D – 6576 - II A/C Condition Soft ASTM C 509
Applications Closures to close off the gap at the top of non-rated walls. Closures strips or plugs with profiles that close off fluted decks. Partition Gaskets where partitions abut other partitions or exterior windows and walls. Expansion joint filler in masonry and concrete. Other applications that require a soft economical gasket resistant to weather, ozone, and/or heat.
Available sizes and packaging Available in sheets, strips or cut parts. Available with self-stick, pressure sensitive adhesive (PSA) one or two sides. Full buns 2" x 48" x 80". Cut to thickness, width and length. Larger dimensions factory spliced or bonded as needed.
Typical Physical Properties Property Test Method Typical Values
Polymer Base Na EPDM Color Na Black or Grey Density –LBS per cubic foot ASTM D 1056 4 ± 1 Compression/Deflection @ 25% Defl. ASTM D 1056 2 to 5 psi Elongation (Die A) ASTM D 1056 200% Ultimate Tensile Strength (Die A) ASTM D - 412 40psi. Water Absorption – maximum increase in weight
ASTM D - 412 5% max.
Service Temperature (F) Low High Continuous High Intermittent
ASTM D – 746
-40ºF 200ºF 250ºF
K Factor – BRU/hr. (sf) ºF inch Na 0.30
Everlastic® EPDM Sponge
3000 Series
Typical Partition/Deck Closure Installation Details
A variety of our products are used for partition and deck closures.
When ordering, oversize the material in thickness (distance from end of partition wall to the glass or mullion). Apply a bead (approx 1/4") of silicone sealant or urethane to the end of the partition wall that abuts the glass mullion. Place the bead 1/2" back from the side of the wall you are working from. Compress the closure and slide into place.
For metal deck flute plugs: Place a bead of silicone or urethane (approximate 1/4") 1/2" back from fluteopening. Place bead on all our sides of flute. Compress plug and slide into place.
Placed between mullion and partition wall.
placed between exterior wall and partition wall.
Existing metal deck
Die cut plugs Die cut plugs with strip
To the best of our knowledge this published information is accurate, however, to determine suitability of material/ WILLIAMS product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss PRODUCTS, INC. or damage resulting from inappropriate usage.
WILLIAMS PRODUCTS, INC. 1750 MAPLELAWN DRIVE - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - TOLL FREE (800) 521-9594 - FAX (248) 643-71
www.williamsproducts.netpage 31-07
TECH DATA Everlastic®DynaShield Ceramic Fiber Grade 600 Fire Rated Joint Filler
PRODUCT DESCRIPTION: Everlastic® DynaShield Ceramic Fiber Grade 600 Fire Rated Joint Filler is a strong, lightweight needled blanket.It is made from long ceramic fibers cross locked through a unique forming process which results in excellent strength. The blankets offer superior flame and heat resisting properties. The fibers are asbestos free and have a melting point of 1843°C (3350°F). Everlastic® DynaShield blankets are manufactured in various densities, operation temperature rangesand fabricated into the Fire Retarding expansion joint fillers and penetration seals.
sealant backer rod
DynaShield DynaShield
metal angle
FIRE-RATED WALLS
(fire side) DynaShield
Typical Physical Properties:Continuous Use Limit 2300°FMelting Point 3200°FShrinkage @ 1000°F 0% backer rod% Binded 0%Density 6-8 lbs/ft³ sealantK-Value (per ASTM-C-177)
400°F 31 Typical Joint Detail800°F 601800°F 1.78
Color Off White Installation:Weight for 60 Rating 10 oz DynaShield Ceramic Fiber should be folded in half and inserted in theASTM D-84 joint under compression. It is not necessary to fill the entire joint depth,
Fuel Contribution 0 fire ratings are achieved according to depth and density of material.Flame Spread 0 (see chart below)Smoke Development 0 Example: 1/2" joint opening for a 1 hour rating = 1/2" x 200% = 1" thick
x 2" deep. Use 1/2" x 4" of DynaShield folded in half. Reference Specifications:ASTM-E-84, ASTM-E-119, & Time Rating Material Thickness Material DepthASTM-E-BS (combustion characteristics) 1 hour 175% to 200% of joint width 2 inchesU.S. Coast Guard-46 CFR 164.009 2 hour 175% to 200% of joint width 4 inchesMilitary - MIL-1-23128A Grade A and B 3 hour 175% to 200% of joint width 5 inchesU.L. HWS 1004, U.L. 263. 4 hour 175% to 200% of joint width 6 inches
™ To the best of our knowledge this published information is accurate, however, to determine suitability of material/ WILLIAMS product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss PRODUCTS, INC. or damage resulting from inappropriate usage.
WILLIAMS PRODUCTS, INC. - 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - FAX (248) 643-7117
www.williamsproducts.net
page 44-07
To the best of our knowledge this published information is accurate, however, to determine suitability of material/product for a specific application is the user’s responsibility. Williams Products, Inc. shall not be liable for any loss or damage resulting from inappropriate usage.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/02 www.williamsproducts.net
TECH DATA Description
· Compressible Lightweight Open Cell Melamine Sponge Sponge Features · NFPA Class A, UBC Class 1 · Fire Resistance, Heat Shielding · Does not ignite at temperatures below 1120°F · Excellent heat insulation properties; no flaming drip · Excellent sound control characteristics in a wide range of frequencies Material Specifications
· ASTM E-84, Steiner Tunnel Test: Flame Spread: 5, Smoke Density: 50 · UL 1715, Corner Burn Test: Passes · NFPA 101
Applications · Interior Partition Closure · Metal Deck Flute Closure Plug · Clean Room Ceiling Tile Seal · Where fire classified foam is required
Typical Physical Properties
Property Test Method Typical Values Density ASTM D - 1667 0.7 pounds / cubic foot Tensile Strength ASTM D3574 8 psi Tear Strength ASTM F3574 0.3 pounds / inch Elongation ASTM D – 3574 8 % Indentation load deflection: Stress strain with 40% Compression Single deflection Repetitive deflection
ASTM D3574
130.5 lbs. 65.25 lbs.
Heat Conductivity K Factor R value
ASTM C177
.24 at 50°F 4.2
Temperature Stability 0 to 302°F Chemical Resistance Organic solvents and various diluted acids
and alkali
Sound Absorption Finish Thickness Coefficients per ASTM C423-90A 125Hz 250HZ 500Hz 1kHz 2kHz 4kHz NRC Mounting Type Natural 1-1/2” 0.08 0.29 0.73 0.94 0.97 0.89 0.75 B (White & Light Gray) 2” 0.05 0.31 0.81 1.01 0.99 0.95 0.80 A
Williams Everlastic®
Fire Classified Closures 1715
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/02 www.williamsproducts.net
TECH DATA Description Self-Stick, closed cell, Neoprene Gasket perforated & cut to dimensions of anchor back plate. Material Specifications ASTM D 1056-2C1 ASTM D 1056-SCE 41 MIL-R-6130C II-A Soft Available Sizes Nominal 1/8" Thick, supplied in panels perforated to size of anchor. Availability varies with size & quantity. Features Custom Fabricated to match anchor size. Self-Stick, pressure sensitive adhesive allows simple and easy installation. Economical, Flexible, Compressible, Resilient, Non-Absorbent, Closed Cell Rubber.
Typical Physical Properties
Property Typical Values Polymer Base CR/EPDM/SBR Density (nominal) 7 ± 2 PCF Compression / Deflection @ 25% 2 to 5 psi. Ultimate Tensile Strength (typical) 100 psi. Elongation (typical) 175% Water Absorption (by weight) 5% max. Accelerated Aging (7 days @ 158°F) Appearance Change Flexibility (180° bend w/out cracking) Change in Compression / Deflection
None Pass ± 30%
Flame Resistance (MVSS - 302) Pass Odor No objectionable odor K Factor 0.30 Service Temperature Low High High Intermittent
-70° F 220° F 250° F
Williams Everlastic® Masonry Anchor Gaskets
Brick Expansion Joints
Neo Seal IV
Column Boxboard Econ-O-Foam
TECH DATAcolumn boxboard
column
block 5/8"
3-1/4"
(Approx. when compressed)Neo-Seal IV 2218-3
brick (Nominal size)
DESCRIPTION
A Unique closed cell Neoprene tubular joint filler. The four connected tubes seal the joint with four pressure points. The Neo Seal IV is very resilient because of its inside diameter assuring continuous sealing in compression and extension.
The Neo-Seal IV will compress to approximately to 3-1/4" in overall width when installed in aconventional 3/8" brick expansion joint.
INSTALLATION:
The Neo-Seal IV is installed in the brick expansion Joint during the construction of the wall.
To the best of our knowledge this published information is accurate, however, to determine suitability of material/™ ™ product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss WILLIAMS or damage resulting from inappropriate usage. PRODUCTS, INC.
WILLIAMS PRODUCTS, INC. 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - TOLL FREE (800) 521-9594 - FAX (248) 643-7117
Everlastic® Neo-Seal IV
TECH DATA Everlastic® Column Boxboard
COLUMN BOXBOARD IS CONSTRUCTED FROM 100% RECYCLED PAPER.
COLUMN BOXBOARD
column
5002-3 5008-3 5004-3
block
1/4" 1/2" 1/4"
ROLLS SHEETS brick 48" X 250' 48" X 48"
COLUMN BOXBOARD Neo Seal (Nominal sizes)
COLUMN BOXBOARD
The Column Boxboard material is used as a isolation material between the structural column and the masonry wall construction. This separation is necessary to prevent the masonry from coming in contact with the column during loading and prevent mortar from being within the same joint. Thisproduct is a cellulose material coated on the weathering side and can be factory scored or scored in the field for bending or breaking to fit any column shape. The nominal thickness of the roll product 1/4"while the sheet product is available at either 1/4" or 1/2" nominal thickness and each being 48" square.
INSTALLATION:
The Column Boxboard material is installed prior to the erection of the masonry wall to assure isolation between the structural column and the masonry wall.
To the best of our knowledge this published information is accurate, however, to determine suitability of material/ ™ product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss WILLIAMS or damage resulting from inappropriate usage. PRODUCTS, INC.
WILLIAMS PRODUCTS, INC. 1750 MAPLELAWN BOULEVARD - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - TOLL FREE (800) 521-9594 - FAX (248) 643-7117
www.williamsproducts.net
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
♦ Expanded, closed cell, plank, polyethylene foam. Economical, lightweight, flexible, compressible, resilient, non-absorbent, inherent bond breaker.
Typical Properties Test Procedure Results
Properties and Characteristics
Density (PCF) ASTM D 3575 Test C 1.3-1.5 nominal
1. Compressive Strengths: Econ-o-Foam is available in a variety of compressive strengths, and can supports a wide range of loads. 2. Weights: Econ-O-Foam is available in densities ranging from 1.5 to 2.2 lbs/cu ft 3. Chemical Resistance: Econ-O-Foam offers excellant stability when exposed to most acides, hydrocarbons, chlorinated solvents, petroleum products, apints, warnishes, thinners, and alcohols 4. Tempurature Range: Econ-O-Foam polyethylene foam has been used successfully in tempuratures ranging from -40°F tp 160°F without significant effect on many of its properties. 5. Water Absorption: Econ-O-Foam polyethylene is virtually impermeable. The amount of water absorbed is negligible even when used in flotation applications. Econ-O-Foam also offers high resistance to transmission of water vapors, with ratings of less than .1 per inch. It contains no water soluble sonstituents. 6. Availability: Econ-O-Foam is available in cut strips. pads, and trimmed or mill run sheets. Rolls are stocked in 1/4", 3/8", and 1/2" thicknesses by 48" wide and 50'0" long.
Cell Size (MM) ASTM D 3576 Dow Modified 1.3
Compression Strength ASTM D 7576 Test B 5% 10% 25% 50%
3.5 5 8 15
Compression Creep ASTM D 3575 Test BB Loaded @ specified PSI static load for 1000hrs 75°F 160°F
5 @ 1.5 psi 5 @ .25 psi
Tensile Strength (psi) ASTM D 3575 Test E 50 Tensile Elongation (%)
ASTM D 3575 Test E 60
Tear Stength (lb/in) ASTM D 3575 Test D 15 Flexural Modulous (psi)
ASTM D 790 300
Bouyancy (PFC) ASTM D 3575 Test AA 55-60
Thermal Conductivity (B1U-in/hr ft °
ASTM D 3575 Test EE Method B 0.4
Thermal Stability (% shrinkage)
ASTM D 3575 Test F Conditioned @ specified temp. with no load 24hrs 48hrs
-1.0 @ 165°F -2.4 @ 165°F
Everlastic® Econ-O-Foam
1390 Series
Adhesives
Williams #37 “A” Adhesive Williams #37 “B” Adhesive Williams #37 “C” Adhesive
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/05 www.williamsproducts.net
TECH DATA Description A high strength, synthetic based adhesive Cream in color Well suited for bonding cellular rubber to its self as well as vinyl, concrete, metal, and wood. Material Specifications ASTM E 84 Packaging Quart and gallon containers. Preparation of Stock Surfaces to be bonded should be free of excess dust, grease, moisture and other contaminants. Metal surfaces should be degreased with a suitable solvent. Application Instructions Thoroughly clean both surfaces to be bonded with recommended cleaner. Surfaces must be free of moisture to insure proper adhesion. Apply one thin, uniform coat of adhesive to both surfaces to be bonded. Allow the adhesive to become tacky to touch. Join with sufficient pressure to insure contact. Best used at room temperature 72°F. Approximate optimum service temperature range 40°F to 90°F. The adhesive should be used directly from storage. Cleaner and Thinner: Thin with Toulene Clean up can be done with Toulene or MEK Precautionary Data: This product is extremely flammable. Vapors may cause flash fires. Vapors may ignite explosively under certain conditions. Keep away from fire, sparks, and sources of heat. Open all doors and windows. Extinguish all flames and pilot lights. Turn off electric motors, stoves, or heaters, or any source of ignition during use and until all vapors have been dispersed. Do not smoke. Close containers after use. Review MSDS Sheet for handling before use. FLASH POINT: Less than 0°F AVOID PROLONGED BREATHING OF VAPORS AVOID PROLONGED AND REPEATED CONTACT WITH SKIN KEEP OUT OF REACH OF CHILDREN STORE AT TEMPERATURES OF 90°F OR BELOW FOR MAXIMUM SHELF LIFE USE WITH ADEQUATE VENTILATION INFORMATION PHONE Out of State: 800-521-9594 In State: 248-643-6400 Chemtel: 1-800-255-3924
Williams Everlastic® #37 “A” Adhesive
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/05 www.williamsproducts.net
TECH DATA Description • No. 37 “B” Adhesive is an air-drying solvent-base neoprene contact adhesive • Black in color • Excellent for joining seams and butt joints of sheet insulations • Well suited for bonding cellular rubber to itself as well as vinyl, concrete, metal, and wood • Makes a resilient moisture and heat resistant bond when used with elastomeric products Material Specifications • ASTM E 84 Packaging • Quart and gallon containers. Application Instructions Mix contents of the container well and apply only to clean, dry, oil-free surfaces. For best results the adhesive should be brush-applied in a thin, uniform coat to both bonding surfaces. The total cure time is 24 to 36 hours when installed by adhering seams and butt joints.
Typical Physical Properties
Property Typical Values Color Black Base Neoprene Solvents Toluene, Hexane, Acetone Solids Content 25% ± 2% Weight per Gallon 9.98 ± 2lbs. Coverage 200sf per gallon Shelf Life 1 year in original sealed container; storage
temperature 60°F to 80°F Minimum Dry Time 2-4 minutes under normal conditions Temperature Limits 220°F/93°C for full Flash Point Less than 0°F Freight Classifications Adhesives NOS. Flammable Liquid 4620 Sub
5, Class 60, UN1133, IMDG Class 3.1
Williams Everlastic® #37 “B”
Adhesive - Black
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/05 www.williamsproducts.net
TECH DATA Description • A general purpose contact adhesive • Typically used to bond countertops, veneers, paneling, ceramic tile stair treads, risers, cove base, and
transition strips • Not recommended for tack strips • Bonds to: wood, vinyl, rubber, leather, drywall, concrete, glass, and metal Preparation of Stock • Allow all material to condition to temperature of 70°F ± 5° for a minimum of 24 hours before,
during, and after installation • All surfaces must be free of dust, dirt, grease, oils, paints, alkali, orany foreign material which could
interfere with proper bonding. • Smooth areas should be roughened with sandpaper or grinding discs. Application Instructions • Brush or roll a generous amount of adhesive to both surfaces with a paintbrush or short nap roller • Allow the adhesive on both surfaces to thoroughly dry prior to installing the product • When dry the adhesive will be tacky to the touch, but will not transfer to the finger • Typical drying times is 20 to 30 minutes, but can be reduced by increasing air movement and
temperature • When dry, position carefully. No adjustment is possible after the adhesive makes contact • Apply sufficient pressure to ensure full contact over the entire area being bonded. A firm bond
develops almost immediately and increases to full strength with 7 days. Cleaner and Thinner: • Remove wet adhesive residue using a clean, white cloth dampened with soapy water • Use mineral spirits for dried adhesive residue, carefully following warnings on container Precautionary Data: • Avoid eye and skin contact, If eye contact occurs, flush with water for 15 minutes and call physician • Wash skin thoroughly with soap and water. • Use with positive fresh air cross-ventilation • Do not take internally. If swallowed do not induce vomiting: call physician immediately KEEP OUT OF REACH OF CHILDREN NOTE: Do not reuse container. Dispose of container and adhesive residue in accordance with federal, state, and local waste disposal regulations. Do not flush adhesive down drains • Keep from freezing • Shelf Life: One year if not opened • VOC content: 0g/L; calculated and reported SCAQMD 1168
Williams Everlastic® #37 “C”
Adhesive Low V.O.C
DIVISION 7 THERMAL and MOISTURE
PROTECTION and CUSTOM DESIGNS
2nd Seal
Wide Joint Seal Closure/Partition Wall
Closure/Metal Deck Flutes Closure/Fire Classified
Backer Rod Roof Expansion Joint
Cavity Wall Baffle using EVA 200 EVA 400
Dust Shield 1350 Series
TECH DATA Williams Everlastic® 2nd SEAL
2nd Seal
Description: Extruded Neoprene /EPDM 60 Durometer profile.
Uses: Williams Everlastic 2nd Seal is placed prior to the Sealantprimary seal assuring a watertight seal should the primaryseal fail. The 2nd Seal can be used in vertical or horizontalapplications or as a primary seal when appearance is notan issue.
Features: Excellent movement capability in extension 250% and compression 50%. No stress on bond line 2nd Seal installed unless exceeding 250 % in extension. Excellent adhesionwhen butting together using 2nd Seal adhesive. Easyto install. A must to assure leak free performance for thethe long run.
Available sizes: For joints 1" to 4" 2nd Seal Extended
Typical Physical Properties Typical Values Property Test Method 60± 5, Shore ADurometer Hardness ASTM D-2240 1000 psi., min.Ultimate Tensile ASTM D-412 1000 psi., min.Ultimate Elongation ASTM D-412 300% minOzone Resistance ASTM D-1149 No Cracks(20% Strain 100 hours A 104°F)Low Temperature Flexibility ASTM D-2137 Pass(5 hours @ - 20°F)Aged in Air (70 hrs @ 158°F) ASTM D-573Change in Hardness ± 15 pts. max.Change in Tensile ± 30% max.Change in Elongation - 50% max. change
(not less than 300%)Compression Set ASTM D-395 20% max.(22 hrs. @ 158°F) Method B
™ To the best of our knowledge this published information is accurate, however, to determine suitability of material/WILLIAMS product for a specific application is the user's responsibility. Williams Products, Inc. shall not be liable for any loss
PRODUCTS, INC. or damage resulting from inappropriate usage.
WILLIAMS PRODUCTS, INC. 1750 MAPLELAWN DRIVE - TROY MICHIGAN 48084 - PHONE (248) 643-6400 - TOLL FREE (800) 521-9594 - FAX (248) 643-7117
www.williamsproducts.net
www.williamsproducts.net
TECHDATA EVERLASTIC® WIDE JOINT SEAL
U.S. Patent Number 5-335-466 DESCRIPTION: Everlastic Wide Seal is a factory cured concaved strip of silicone sealant adhered to rectangular
strip of polyesther polyurethane backer. BASIC USES: Everlastic Wide Joint Seal is designed for sealing vertical and horizontal (non-traffic)
expansion joints that measure 1-1/2” or greater. HOW TO USE: The opened cell polyesther polyurethane is larger than joint opening, the silicone sealant is of
lesser size than the joint opening. Compress the polyurethane and placed in the joint, recessing and centering the silicone face l/4 into the joint. There will be a reveal on each side of the silicone sealant (being its smaller than the joint opening) which is to be caulked with a wet silicone sealant and then tolled.
COLORS: 16. Custom colors also available. MAINTENANCE: If the silicone seal becomes damaged, replace damaged portion. Clean surface in damaged area
and repair with fresh silicone sealant.
www.williamsproducts.net
FEATURES:
1. Performance in respect to life expectancy, it lasts because the WJS is not effective by ozone or ultraviolet rays and has excellent stability in regards to movement capability and modules. 2. The WJS has movement capability of plus or minus 50%. 3. The esthetics of the WJS allows for larger joint design, which in return reduces the stress on the
bond line. The chances of a successful sealant installation are excellent. 4. Primerless adhesion to a variety of substrates, including masonry and concrete, and no staining. 5. Easy to install, no anchoring systems. mechanical fasteners, cutting of substrates or waiting for expansion to
accrue. 6. Having to caulk the reveals on each of the cured sealant, makes it necessary fill to the full depth ------no
"cheating" on the amount of sealant placed. 7. The WJS is placed in the joint----not over as a bandage.
SURFACE CONDITIONS
Surfaces to be sealed must be free of dirt, dust, moisture, frost or other contaminates that could interfere with adhesion or bond of the sealant.
HEAD JOINT
CURED SEALANT
WET I
Compress polyurethane and place in joint with face of cured sealant recessed 1/4"
Everlastic® Wide Joint Seal (WJS)
Installation
WET I
Caulk reveals on both sides with wet sealant and tool. Caulk from
'-----1 face edge of cured sealant to face edge of substrate.
Caulk Butt recessed end of
WJS to head and caulk
HORIZONTAL TO VERTICAL
Caulk
Measure the distance from the previously installed WJS to bottom of joint. Cut to length. Cut 1/2" of cured sealant from flush end and caulk with wet sealant.
Butt recessed end to flush end and caulk across opening.
Flushed end 4+-- Recessed
end
Butt flush end of horizontal to vertical.
SILL JOINT
CENTERING
9CP ANGLE Caulk
Keep cured silicone sealant centered in joint. If off
centered, push cured sealant in opposite direction.
Cut back 1 1/4" of polyurethane and remove, place WJS in horizontal joint. Place the flush end of vertical WJS under the exposed sealant of the horizontal WJS and caulk reveal.
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description
Everlastic® EPDM Sponge is expanded, closed-cell, Ethylene Propylene Diene sponge rubber. Non-absorbent, compressible, resilient, provides good thermal and moisture installation Everlastic® EPDM Sponge is generally resistant to acids, alkali, oxidation and ozone. Everlastic® EPDM Sponge is not recommended in applications that require oil resistance.
Material Specifications ASTM D - 1056 - 2A1 ASTM D – 6576 - II A/C Condition Soft ASTM C 509
Applications Closures to close off the gap at the top of non-rated walls. Closures strips or plugs with profiles that close off fluted decks. Partition Gaskets where partitions abut other partitions or exterior windows and walls. Expansion joint filler in masonry and concrete. Other applications that require a soft economical gasket resistant to weather, ozone, and/or heat.
Available sizes and packaging Available in sheets, strips or cut parts. Available with self-stick, pressure sensitive adhesive (PSA) one or two sides. Full buns 2" x 48" x 80". Cut to thickness, width and length. Larger dimensions factory spliced or bonded as needed.
Typical Physical Properties Property Test Method Typical Values
Polymer Base Na EPDM Color Na Black or Grey Density –LBS per cubic foot ASTM D 1056 4 ± 1 Compression/Deflection @ 25% Defl. ASTM D 1056 2 to 5 psi Elongation (Die A) ASTM D 1056 200% Ultimate Tensile Strength (Die A) ASTM D - 412 40psi. Water Absorption – maximum increase in weight
ASTM D - 412 5% max.
Service Temperature (F) Low High Continuous High Intermittent
ASTM D – 746
-40ºF 200ºF 250ºF
K Factor – BRU/hr. (sf) ºF inch Na 0.30
Everlastic® EPDM Sponge
3000 Series
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products Discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage Arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning The possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Material Specifications
Black in color Cross-Linked, Closed Cell, Ethylene/Vinyl Acetate Foam Lightweight, Flexible, Resilient, Non-Absorbent Foam Resistant to Heat, Ultraviolet, Acids, Alkalis, Gasoline & Oil, Aromatic Hydrocarbons, Ketones,
Oxidation and Ozone Uses As a Hot or Cold Applied Sealant Backup To fill Vertical and Horizontal Joints Acoustical Partition Closures Corrugated Deck Closures, and many other uses Available Sizes 1/8” thru 4” thickness May be laminated to other thickness’ Widths: cut to order, Minimum ½” , Maximum 48”
Typical Physical Properties Property Test Method Typical Values
Density (lbs. /cu. Ft.) ASTM D 3575 2.3 ± 0.5 Compression / Deflection (psi Required to compress to 25%)
ASTM D 1056 5 ± 2
Compression Recovery @ 50% Extrusion @ 50%
ASTM D 1752 Modified (10 psi. Min. to 25 psi. Max.)
14.5 psi. 99%*
0.10 inch** Ultimate Tensile Strength ASTM D 3575 50 psi. Water Absorption ASTM D 1056 <5% (max. gain by weight) Odor No Objectionable Odor K Factor 0.25 Service Temperature Low High Continuous High Intermittent
-70° F 180° F 290° F
Flame Resistance MVSS-302 PASS Accelerated Aging (7 Days) 158° Flexibility 180° Bend Without Cracking Appearance Change in Compression/Deflection
Pass None ± 30
After Removal of Load, material shall recover to 95% of original thickness within 24 hours. ** When compressed to 50% of original thickness with three sides restrained; the unrestrained edge shall not extrude
more than 0.25 inches.
Williams Everlastic® EVA 200G
To the best of our knowledge this published information is accurate, however, to determine suitability of material/product for a specific application is the user’s responsibility. Williams Products, Inc. shall not be liable for any loss or damage resulting from inappropriate usage.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 REV 1/02 www.williamsproducts.net
TECH DATA Description
· Compressible Lightweight Open Cell Melamine Sponge Sponge Features · NFPA Class A, UBC Class 1 · Fire Resistance, Heat Shielding · Does not ignite at temperatures below 1120°F · Excellent heat insulation properties; no flaming drip · Excellent sound control characteristics in a wide range of frequencies Material Specifications
· ASTM E-84, Steiner Tunnel Test: Flame Spread: 5, Smoke Density: 50 · UL 1715, Corner Burn Test: Passes · NFPA 101
Applications · Interior Partition Closure · Metal Deck Flute Closure Plug · Clean Room Ceiling Tile Seal · Where fire classified foam is required
Typical Physical Properties
Property Test Method Typical Values Density ASTM D - 1667 0.7 pounds / cubic foot Tensile Strength ASTM D3574 8 psi Tear Strength ASTM F3574 0.3 pounds / inch Elongation ASTM D – 3574 8 % Indentation load deflection: Stress strain with 40% Compression Single deflection Repetitive deflection
ASTM D3574
130.5 lbs. 65.25 lbs.
Heat Conductivity K Factor R value
ASTM C177
.24 at 50°F 4.2
Temperature Stability 0 to 302°F Chemical Resistance Organic solvents and various diluted acids
and alkali
Sound Absorption Finish Thickness Coefficients per ASTM C423-90A 125Hz 250HZ 500Hz 1kHz 2kHz 4kHz NRC Mounting Type Natural 1-1/2” 0.08 0.29 0.73 0.94 0.97 0.89 0.75 B (White & Light Gray) 2” 0.05 0.31 0.81 1.01 0.99 0.95 0.80 A
Williams Everlastic®
Fire Classified Closures 1715
Backer Rod
Neoprene Backer Rods Standard CCPE
Hot Rod Tundra Foam
Soft Type
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA
Everlastic Neoprene Cord Material: Closed Cell neoprene Sponge Rubber Specification: ASTM D-1056, 2C1, or ASTM C-509 Diameters Available: 1/8”, ¼”, 3/8”, ½”, 5/8”, ¾”, 1”, 1-1/4”*, 1-3/4”*, 2”*, 2-3/8”, 2-3/4” *Standard sizes with inside diameters, pther sizes by special order
Standard CCPE Backer Rod Material: Closed Cell Polyethylene Foam Specification: TT-S-00227E Diameters Available: 1/4", 3/8”, 1/2”, 5/8”, 3/4”, 7/8”, 1”, 1-1/4”, 1-1/2”, 1-3/4”, 2”, 2-1/2”, 3”, 4” Diameters 1-1/4” or less packaged in coils, larger sizes in six foot pieces.
Hot Rod XL
Material: Crosslinked Closed Cell Polyethylene Foam Specification: ASTM D 1622 Diameters Available: 3/8”, 1/2”, 5/8”, 3/4”, 1”, 1-1/4”, 1-1/2”, 1-3/4”, 2” Diameters 1-1/4” or less packaged in coils, larger sizes in six foot pieces.
Soft Type Backer Rod
Material: Extra Soft & pliable, Closed Cell Polyethylene Foam Specification: ASTM D 249 - Type 3 Diameters Available: 3/8”, 5/8”, 7/8”, 1-1/8”, 1-1/2”, 2” Diameters 1-1/4” or less packaged in coils, larger sizes in six foot pieces.
Tundra Foam
Material: Open Cell Polyethylene Foam Specification: ASTM D 1564 Diameters Available: 3/8”, 5/8”, 7/8”, 1”, 1-1/8”, 1-1/2”, 2” Furnished in twice compressed six pack bundles.
Williams Backer Rods
Everlastic® Neoprene Backer Rods
Description Extruded and molded closed cell neoprene sponge Use As hot or cold applied sealant backup; to fill vertical and horizontal joints. Resistant to heat, ultraviolet light and many chemicals.
Physical Properties Typical Profiles ASTM Designation D-1056-68
D-1056-78 D-1056-85
Suffix Letters
SCE-41 RE-41 2C1
CE1P2MP
MIL R-6130C Type Grade Condition
II-A Soft
Physical Properties Color Black Black (Grey) Compression-Deflection 25% Defl. (psi) (kN/m2)
2-5 (14-35)
Ultimate Tensile Strength (Typical Properties) psi (kN/m2)
100 (700)
Elongation (Typical Properties) % 175 Density lb./ft3
g/cc
7+/-2 0.11+/-.03
Fluid Immersion, 7 days @ 73ºF Ref. Fuel B, weight change max. %
250
Accelerated Aging, 7 days @ 73ºF Flexibility
180º bend without cracking Appearance Change
Change in compression-defl.
Pass None +/- 30
Maximum Weight % 5
Odor
No Objectionable Odor
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description Standard Backer Rod is an ideal non-absorbent compressible backup material. It is inserted into a joint to control sealant depth to create a backstop to:
Allow proper sealant tooling Allow proper wetting of the joint surfaces Yield a proper bond breaker between the Backer Rod and sealant
It can also be used as a temporary joint seal. Uses Commonly used in glazing installations, window and door applications, expansion joints, curtain wall joints, partitions, log construction, pavement joints, repairs, pre-cast units and copings.
Compatibility Standard Backer Rod is compatible with butyl, polysulfide, acrylic polyurethane, silicone, and most other cold applied sealants. Composition and Materials Standard Backer Rod is an extruded round, closed cell, low density polyethylene foam material with a skin-like outer texture. It is highly flexible and compressible for easy installation. Available in stock grey and several other colors on a custom basis. Available in a wide variety of diameters (see Table 1) Type C – Closed Cell Backer Rod
Standard Backer Rod Closed Cell Polyethylene Foam
(CCPE)
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
Technical Data Standard Backer Rod is chemically inert and will resist oil, gasoline, and most other solvents. This material will not stain, nor adhere to, sealant materials and is non-exuding (refer to Table 2 for typical physical properties) Standard Backer Rod meets or exceeds the requirements of ASTM C 1330 Type C Installation Joint or opening must be clean, dry, and free of obstructions. Using Table 3, select the proper rod diameter and cut to length or use directly from spool. With a blunt instrument, or roller, uniformly install rod at the level recommended by the sealant manufacturer, specifier, or architect involved. Generally, the depth of the joint after the backer rod is installed is one half the width. Very large and very small joints vary in terms of this depth to width ration. DO NOT PUNCTURE, STRETCH, OR OVERLY COMPRESS.
TECH DATA Description Hot Rod XL is an ideal non-absorbent compressible backup material inserted into a joint to control sealant depth, create a backstop to: Allow proper sealant tooling Allow proper sealant wetting of the joint surfaces Yield proper bond breaker between the backup material and the sealant It can also be used as a temporary joint seal. Uses Hot Rod XL is a backup material for most hot pour sealants used to fill contraction and expansion joints of concrete highways, runways, driveways, and parking lots. (see application procedures below)
Compatibility Hot Rod XL is compatible with most rubber-asphalt and coal tar-rubber polymer thermoplastic compounds. Composition and Materials Hot Rod XL is an extruded round, closed cell, low-density polyethylene foam material which has been specially crosslinked to withstand temperatures in excess of 400°F. This material is available in beige only and in a wide variety of diameters. (see table 1)
Hot Rod XL
Technical Data Hot Rod XL is chemically inert and will resist oil, gasoline, and most other solvents. This material will not stain, soak up moisture, nor adhere to sealant materials, and is non-exuding. (refer to Table 2 for typical physical properties) Installation The joint depth must be great enough to allow for the proper installation of the Hot Rod XL bond breaker and hot pour sealant. The joint width will be determined by the appropriate thermal expansion coefficient as related to anticipated temperature variances. Joint walls must be as smooth and as even as possible and be free of any loose residues or foreign materials. Joints should also be dry and frost free. Using table III, select the proper rod diameter and cut to length or use directly from spool. With a sized rubber tool, blunt instrument, or by hand, install rod at the level recommended by the sealant manufacturer, specifier, or governmental agency involved.
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description Tundra Foam is an ideal non-gassing backup material which is inserted into construction and pavement joints to: Control sealant and caulking depth Create a backstop to allow proper sealant tooling and configuration Allow proper sealant airing and yield a proper bond breaker It is ideal for non-uniform joint sizes. Uses Commonly used in expansion and contraction joints, window glazing, curtain wall construction partitions, precast assemblies and copings, parking decks, bridge construction, and more.
Compatibility Tundra Foam is basically an inert composition and therefore compatible with all known hot and cold applied sealants, including silicone and rubber asphalt. Composition and Materials Tundra Foam is a fabricated round, open cell polyurethane foam material. It is highly flexible and compressible for easy application. It is available in a wide variety of sizes, each capable of fitting a number of different joint sizes. (see Table 1)
Tundra Foam
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
Technical Data Tundra Foam will resist oil, gasoline, and most other solvents. This material is ordorless, will not stain, and will not adversely adhere to sealant and caulking materials. (refer to Table II for typical physical properties) Installation The joint depth must be great enough to allow for the proper installation of the Tundra Foam and the hot or cold sealant or caulking material. Joint walls must be as smooth and even as possible and be free of any loose residues or foreign materials. Joints should also be dry and frost-free. With a convenient tool or by hand, insert Tundra Foam into joint at a level recommended by the sealant manufacturer. Cold applied sealants generally recommend that the depth of the joint after the backer rod is installed be one half of the width. In hot pour applications, it is generally recommended the depth of the joint be a 1:1 ratio in terms of backer rod to sealant.
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
TECH DATA Description Soft Type Backer Rod is a soft, grey, pliable, non-gassing, backup material inserted into an expansion or contraction joint to: Control sealant depth
Create a backstop to allow proper sealant tooling Ensure sealant adhesion to joint surfaces only Yield a proper bond break between backup material and sealant
It can also be used as a temporary joint seal. Uses Particularly suited for specialty applications where standard backer rods are not appropriate. Ideal in irregular joint applications, particularly where self-leveling, flowable sealants are employed. Also recommended with sealants where bubbling concerns are critical. May also be used in place of most standard backer rod applications. (see illustration below)
Compatibility Soft Type Backer Rod is virtually an inert composition and therefore compatible with all known cold applied sealants, including butyl, polysulfide, acrylic, polyurethane, and silicone. Composition and Materials Soft Type Backer Rod is polyethylene foam consisting of both open and closed cells on the inside with a skin-like outer texture. It is highly flexible, pliable, and compressible for easy installation. This material is available in a wide variety of diameters.
Soft Type Backer Rod
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Blvd. • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.wiilliamsproducts.net
Technical Data Soft Type Backer Rod is chemically inert and will resist oil, gasoline, and most other solvents. This material will not stain, nor adhere to, sealant materials and is non-exuding (refer to Table 2 for typical physical properties) Soft Type Backer Rod meets or exceeds the requirements of ASTM C 1330 Type B Installation Joint or opening must be clean, dry, and free of obstructions. Using Table 3, select the proper rod diameter and cut to length or use directly from spool. With a blunt instrument, or roller, uniformly install rod at the level recommended by the sealant manufacturer, specifier, or architect involved. Generally, the depth of the joint after the backer rod is installed is one half the width. Very large and very small joints vary in terms of this depth to width ration. Avoid puncturing, stretching, or over compression.
Everlastic® NN-1 1040 Series Applications
Description:
As Roof Seal at Non-Supported Deck
Or as Roof Seal at Expansion Joint
Everlastic® EVA‐200 Applications
Compartmentalization of the cavity wall system will equalize the negative pressure within the wall cavity to the exterior positive pressure more quickly and efficiently when using PVC brick vents, cell vents or open head joints.
This is of significant importance when considering that a driving rain is sucked through the brick veneer into the cavity by the negative pressure within the cavity.
The quicker the pressure is equalized the less the water in the cavity.
It is very important to compartmentalize at the corners to avoid air flowing around the corner carrying moisture down the adjacent cavity.
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description • Cross-Linked, Closed-Cell, Ethylene/Vinyl/Acetate Foam
• Gray in color
• Lightweight, Flexible, Resilient, Non-Absorbent Foam. • Resistant to Heat, Ultraviolet and many other chemicals. Specifications • ASTM D-3575 Available Sizes • Thickness from 1/8” to 4” • Widths from 1/2” to 48” • Full Sheets 48” x 90” • Available with Pressure Sensitive Temporary Positioning Adhesive (PSA). Applications • Use as a Hot or Cold Applied Sealant Backup • To fill Vertical and Horizontal Joints • Acoustical Partition Closures • Corrugated Deck Closures; and many other uses.
Typical Physical Properties Property Test Method Typical Values
Density (lbs./cu. Ft.) ASTM D-3575 4 ± 0.7 Compression Deflection 25% ASTM D-1056 9 ± 2 Elongation 200% Typical Extrusion @ 50% (see note 1) 0.10 inch Ultimate Tensile Strength ASTM D-3575 80 psi. Water Absorption ASTM D-1056 5% max. gained by weight Odor No Objectionable Odor K Factor 0.30 Service Temperature Low High Continuous High Intermittent
ASTM D-746 -100° F 160° F 180° F
Flame Resistance MVSS -302 Pass Accelerated Aging (7 days @ 158°F) 180° Bend Without Cracking Appearance Change Change Compression/Deflection
Pass None ± 30%
1.) When Compressed to 50% of original thickness with three sides restrained; The unrestrained edge shall not extrude more than 0.25 inches.
Williams Everlastic® EVA 400G
We do not guarantee the applicability or accuracy of this information or the suitability of our products for any given situation Users should make their own tests to determine the suitability of any product for their particular purpose. The products discussed are sold without warrantee, either expressed or implied, buyer assumes all responsibility for any loss or damage arising from the handling or use of our products, whether done in accordance with directions or not. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent.
Williams Products, Inc. • 1750 Maplelawn Drive • Troy, Michigan 48084 • Ph: 800-521-9594 Fax: (248) 643-7117 www.williamsproducts.net
TECH DATA Description Open Cell Polyurethane
Off-White in color Available Sizes Available in Crude Buns, Sheeted Rolls, Sawcut Shapes, and Roll Goods with Pressure Sensitive
Adhesive Applications Medium Density Polyether Foam, Firm ILD Range, designed to meet a broad range of Furniture,
Automotive Seating, and Dust Shields for Ceiling Tile.
Typical Physical Properties
Property Test Method Typical Values Color Off-White* Density ASTM D 3574 1.5 ± 0.2 pcf. Tensile Strength ASTM D 3574 12 psi. min. Eklongation ASTM D 3574 150% min. Tear Resistance lbs/in. ASTM D 3574 1.5 pli. min. Compression Set ASTM D 3574 10% max Odor Recticel QC No Objectionable Odor Load Deflection ASTM D 3574 40 ± 4 lbs. Flammability MVSS – 302 Pass Cold Flexibility No Deterioration Cell Size 60cpi. * Will discolor to cream and/ or Yellow with age.
Williams Everlastic® Dust Shield Ceiling Tile
1350 Series
SEALANTS
This guide only offers a general representation of our color offering. Colors viewed on a computer screen and then printed will vary and will never be an exact representation of the actual pigment. When matching is critical, please refer to our color card or sample color strips.