wheelloader i e a4
TRANSCRIPT
-
7/23/2019 Wheelloader i e a4
1/7
Special Vehicle Series :01
AssemblyInstructionsWheel Loader
http://www.canon.com/c-park/en/
View of completed model
* This model was designed for Papercraft andmay differ from the original in some respects.
Tools Assembly tip
Key to symbols
ScissorsRuler, set squareGlue (Wood glue or craft glue recommend)Exhausted ballpoint pen (out of ink)Toothpicks (for use in applying glue)
Tweezers (useful for handling small parts)Pencil
Write the number of each part on the reverse side of the part in pencil
upon cutting it out, to be sure you can tell which part is which later.
Before gluing, crease the paper along
mountain and valley fold lines. Trace along
the folds with a ruler and an exhausted
ballpoint pen (out of ink) to get a sharper fold.Make sure rounded sections are nice and stiff.
Pattern
Red dot
Green dot
Blue dot
Assembly instructions
Solid line
Dashed anddotted line
Dotted line
Solid red line
Diagonalgrey lines
Mountain foldFold so that the printedpattern faces outside.
Fold so that the printedpattern faces inside.
Valley fold
Cut parts outalong this line.
Cut a notchalong this line.
Cut these areasout.
The dots show where to gluethe pieces together. Glue thepieces together as shown in thefollowing examples.Some parts must be gluedtogether along the cut surfaces.
Glue parts with the samenumber together. (Numbers arenot printed on very small parts.)
Glue areas within the samepart together.
Glue to the reverse side of thespecified part.
This denotes a partthat must be able tomove after the modelis completed. Be sureto crease these partssufficiently.
Glue
Insert
Glue tab
Reverse side ofpaper
Movable part
(without gluing)
Red arrow
Blue arrow
Light blue
Light grey
Glue, scissors and other tools may be dangerous to young childrenso be sure to keep them out of the reach of young children.
Assembly Instructions: Seven A4 sheets (No. 1 to No. 7)Build this model with careful reference to the Assembly Instructions.
-
7/23/2019 Wheelloader i e a4
2/7
Assembly InstructionsWheel Loader
Assemble the cab.Glue flaps a and b in order.
Use care to get the shape rightwhen assembling this part,referring to the cross sectionat right.
Cross section
Close this surface last and glue it in place.
Glue flaps a, b, and c in order.
-
7/23/2019 Wheelloader i e a4
3/7
Glue flaps a, b, c, d, and ein order. Leave an opening here.
Shape this part before gluing it.
This is a moving part.Do not glue it.
Glue flaps a, b, and c in order.
Glue to part G.Use care to attach this partin the right direction,referring to the illustration.
Fold the left and right flapsback and glue each in place.
Use care with the angles at which you glue parts12 and 13 in place, to ensure the two parts are parallel.
Cross section
Cross section
Moving part
Moving part
Moving part
Fold down the sides, then bendthe center down along the curvededges and glue it in place.
Apply a small amount ofglue to the cut surface ofthe paper as well, and gluethis part in place alongwith the shape of thebucket. (The bucket doesnot have any glue tabs.)
Glue the back sides of the paperparts together, in numbered order.Fold in the ends of parts 22 and
28 and then glue them in place.
Glue parts 17 and 18 tothe reverse side of the bucket.
Reverse side
Assembly InstructionsWheel Loader
-
7/23/2019 Wheelloader i e a4
4/7
Glue flaps a and b in order.
Insert into the openingin part F.
Referring to the cross section,insert this part through the holes andfix it in position at top and bottom.
Cross section
Overhead view
This is the joint betweenthe front and rear sections.
Assemble in the same way as part 31.
Assembly InstructionsWheel Loader
-
7/23/2019 Wheelloader i e a4
5/7
Assembly InstructionsWheel Loader
-
7/23/2019 Wheelloader i e a4
6/7
-
7/23/2019 Wheelloader i e a4
7/7
Assembly InstructionsWheel Loader
Apply glue to the cut surface of
the paper and glue this part tothe body of the wheel loader,concealing the glue tabs.
On parts with no glue tabs,apply glue to the cutsurface of the paper.
Fold the shaft part in and glue these parts together.After attaching them to the body of the wheel loader,adjust the angle of the shaft so the headlightpoints straight forward.
Finished!Last, assemble the nameplate and
display it together with your model.