what’s in the box? · blue-ch3) each represent one channel and will turn on their channel when...
TRANSCRIPT
1
What’s in the Box?
• 1 Color CCD Infra-red Weather Proof Camera
• 1 7" TFT LCD Color Monitor w/Universal Mount/Stand & Wire
• 1 Power Harness
• 1 66’ Camera Cable
• 1 Remote Control
• 1 Power Connection Wire
• 1 Double RCA + Power Converter
(to connect external audio, video and power)
• 1 Screw Kit for installation
2
3
Table of Contents
Introduction ...................................................................................................4
Safety Information ..................................................................................5-7
Before Beginning Installation...................................................................8
Installation Guide.........................................................................................9
Wiring Camera & Monitor.................................................................10-11
Installation Diagram .................................................................................12
Installing the Monitor ..............................................................................13
Monitor Operation.....................................................................................14
Splitting & Splicing ...................................................................................15
Positioning.................................................................................................. 16
Monitor Dimensions..................................................................................17
Monitor Specifications .............................................................................18
Camera Dimensions...................................................................................19
Camera Specifications..............................................................................20
Troubleshooting..........................................................................................21
Warranty.......................................................................................................22
Disclaimer ....................................................................................................23
4
Introduction
Congratulations on purchasing a Rear View Backup Camera
System! With this manual you will be able to properly install and
operate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already
exists in your vehicle. The Backup Camera System should not be
used as a substitute for the standard rear view mirror or for any
other mirror that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with a TV viewer or screen located
forward of the back of the driver’s seat or in any location that
is visible, directly or indirectly, to the driver while operating the
vehicle.
Please read all of the installation instructionscarefully before installing the product. Improperinstallation will void manufacturer’s warranty.
5
Safety Information
Please read the entire manual and follow the instructions andwarnings carefully. Failure to do so can cause serious damageand/or injury, including loss of life. Be sure to obey all applica-ble local traffic and motor vehicle regulations as it pertains tothis product. Improper installation will void manufacturer’swarranty.
USAGE
• The Rear View Camera Systemis designed to help the driversafely detect people and/orobjects helping to avoiddamage or injury. However,you the driver, must use itproperly. Use of this system isnot a substitute for safe,proper or legal driving.
• Never back up while lookingat the monitor alone. Youshould always check behindand around the vehicle whenbacking up, in the same wayas you would if the vehicledid not have the Rear View
Camera System. If you backup while looking only at themonitor, you may causedamage or injury. Alwaysback up slowly.
• The Rear View Camera Sys-tem is not intended for useduring exstensive back-upmaneuvers or backing intocross traffic or pedestrianwalkways.
• Please, always remember,the area displayed by theRear View Camera System islimited. It does not displaythe entire panorama that isbehind you.
6
INSTALLATION
• Electric shock or productmalfunction may occur ifthis product is installedincorrectly.
• Use this product withinthe voltage range specified.Failure to do so can causeelectronic shock or productmalfunction.
• Take special care whencleaning the monitor.
• Make sure to firmly affix theproduct before use.
• If smoke or a burning smellis detected, disconnect thesystem immediately.
• Where the power cable maytouch a metal case, cover thecable with a friction tape. Ashort circuit or disconnectedwire may cause a fire.
• While installing the RearView System be careful withthe wire positioning in orderto avoid wire damage.
• The Rear View System shouldonly be used when thevehicle is in reverse.
• Do not watch movies oroperate the monitor whiledriving; as it may cause anaccident.
• Do not install the monitorwhere it may obstruct driversview or obstruct an air bagdevice.
• Dropping the unit may causepossible mechanical failure.
Safety Information
7
Safety Information
IN NO EVENT SHALL SELLER OR MANUFACTURER BELIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OFANY NATURE, OR LOSSES OR EXPENSES RESULTING FROMANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
If you have questions about this product, contact:
9049 Tyler Blvd. • Mentor, Ohio 44060Phone (440) 974-8888 • Fax 800-841-8003
Email: [email protected] www.buyersproducts.com
8
Before Beginning Installation
Before drilling please check that no cable or wiring is on theother side of the wall. Please clamp all wires securely to reducethe possibility of them being damaged while vehicle is in use.Keep all cables away from hot or moving parts and electrical noisy components.
We recommend doing a benchmark test before installationto insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)hole should be drilled for passing camera cable through vehicleswalls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed,perform a system function test by temporarily connecting thesystem. If the system seems to not be operating properly seetroubleshooting (page 22).
Before Beginning Installation
9
Installation Guide
Cable 1. Be sure to position the cable properly. The camera cable uses
aircraft grade connectors which means the camera cable canbe exposed to all weather elements. Do not run the cable oversharp edges, do not kink the cable and keep away from HOTand rotating parts.
2. Fasten all cables and secure all excess cable.
Monitor1. To Attach the Pedestal mount to the dashboard or to the
headliner use self-tapping screws and/or the adhesive pad.2. Attach monitor to mount, and adjust mounting angle to allow
optimum driver viewing comfort. (see figure 1.1 on page 12)
10
Installation Guide
The Power Harness.• To power the system connect
the power (RED) 12V+ wire toignition power and the ground(BLACK) wire to chassis ground.
• These are the only wiresneeded to power the entiresystem and all the cameras.Each camera can be seen atany time by simply pressingthe power button and usingthe V1/2 button to toggle.
• The three positive trigger wires(WHITE-CH1, BROWNCH2,BLUE-CH3) each represent onechannel and will turn on theirchannel when the trigger wireis energized with 12V.
• "Camera 3" is the designatedbackup channel. To have thethe backup camera come onwhen you go into reverse, con-nect the BLUE wire to reversepower (or any power sourcethat comes on only in reverse).
• The other channels can simi-
larly be triggered (i.e. side cam-eras can be triggered by the turnsignals etc.)• To automatically have cameraand monitor turn ON when vehi-cle activates, simply twist BLUEpositive trigger 12V+ to RedPower line 12V+ and wire to ig-nition power.
Note: This setup will disablethe menu in channel 3. Toaccess the menu simply moveto channel 1 or 2 and all thechanges will apply to channel3.Note: When the blue wire isactive it will have precedenceover the other triggers.Therefore, if you wish to usemultiple triggers, do notattach the blue trigger toconstant power.
11
Wiring Camera & Monitor
• Audio: There is audio onchannels 2 and 3. On channel 3the blue trigger wire must beenergized (12V) to activate theaudio. On channel 2 the audiois always on.
• Grid-lines: The grid-lines arealso carried through the bluewire. To use the grid-lines forreversing, connect the bluewire to a reverse power.
• There is a built-in voltageregulator for our systems whichcan handle 12-24 volts. Realconsumption is 10 to 30 Volts.
Note: The camera andmonitor can always beactivated by manuallypushing the power button onmonitor. This is in addition toutilizing the positive triggers.
Note: If connecting power directly to battery, the camerais always ON and therefore candrain battery. Therefore it isrecommended to connectpower to an ignition switchedaccessory power source.
12
Installation Diagram
Figure 1.1 Figure 1.2
Figure 1.3 Figure 1.4
Connection of UBracket
Connection ofFlushmount Bracket
13
1. DC12V-24V2. Ground3. Port #3 (blue)4. Port #2 (brown)5. Port #1 (white)
12345
3 Amp Fuse
Monitor
Power Harness
66ft Extension Cable
Camera
OptionalCameraAvailable
14
Monitor Operation
MENU REVV1/V2 ▼
▼
POWERON /OFF
MENU/SELECTIONBUTTON
CAMERASELECTION
DOWNARROW
UPARROW
ROTATEIMAGE(Back/Exitwhen inMenu Mode)
• Use "BRIGHTNESS" "CONSTRAST" "SATURATION" “SHARPNESS" toadjust the image properties.• Day/Night Mode: Mode 1 will turn on the Back-lit buttons. Mode 2will turn on the auto-dim feature on the monitor.
• Name: Change the name of each individual channel.• Trigger source: Change the channel destination for each trigger.• Trigger delay: Adjust the delay time on each trigger.• Distance Grid: Choose what channel the distance grid will display on.• Grid Position: Move the grid-lines.• Reset: Reset all settings to factory default.
15
Splitting & Splicing
Installing sun shield: Put shade cover onthe display. Installing back cover: Put themonitor with shade cover in the back cover(only for embedded monitor)
Splitting back cover: Hold monitor with 2hands and detach with fingers, as indicatedby arrows. (only for embedded monitor)
Splitting sun shield: Take the monitor withthe left hand and detach with right hand asindicated by the white arrow. (see below)
1. Red - Power (+)2. Yellow - Video3. White - Audio4. Black - Ground (-)
1.2.
3.4.
16
Positioning
17
5.25”
7”
power
video selectdown/up
menu
mirror/normalimage
PowerOn/Off
Menu/SelectionButton
CameraSelection
DownArrow
UpArrow
RotationImager(Exit inMenuMode)
Monitor Dimensions
18
Monitor Specifications
TFT LCD Digital Monitor
Screen Size 7”
Dot Resolution 800H x 3 (RGB) x 480V
Display Format 16:9 / 500:1
Display Brightness 400cd/m2
Viewing Angle U:50° / D:60° / R:70°
Video Input 3 channel
Video Source 1Vp-p, 75�
Power Supply DC 12V-24V (+/- 10%)
Power Consumption 5W
Operating Temperature -30°C ~ +80° C
Video System Auto NTSC/PAL
Overall Dimensions 7”L x 5.25”H x 1”D
Weight 400G
Impact Rating 5G
Dot Pitch 0.192H x 0.1805V
Sync System Internal
19
table of contentsCamera Dimensions
3”
3.25”
20
Camera Specifications
Camera 1/4” Sharp® Color CCD
Picture Elements 250,000 pixels
Gamma Correction r=0.45 to 1.0
Image Sensor 540TVL NTSC 769H x 494 V, PAL 752H x 582V
Lens 2.1mm
View Angle 130°
Sync System Internal Synchronization
Infrared distance 50 Feet (18 Infrared IR)
Usable Illumination 0 Lux (IR On)
Power Source DC 12V-24V (+/- 10%)
S/N Ratio More than 48dB
Electronic Iris 1/50, 1/60-1/100,000sec
Video Output 1Vp.p 75ohm
IR Switch Control ACDS Automatic Control
Impact Rating 20G Vibration/100G Shock
Operating Temperature -30°C~70°C
Storage Temperature -35°C~80°C
21
Troubleshooting
Monitor Displays Blue Screen & Displays No Signal• Do a hard reset, unplug all
cables and power cables leaveout for 1 minute and thenre-connect them.
• Check to ensure that the con-nection to the camera is tight.
• Verify camera cable is pluggedinto port labeled Backup Camera
• Verify that the blue positive
trigger on power harness isput to power 12v+.
If the problem still persists, ver-ify that alternate ports work. Ifalternate ports do not work, re-move Blue Trigger wire from12V+ and select alternate chan-nels.
Monitor Will Not Power-Up (no backlight on power button)
• Check fuse• Check 12v+ to monitor
• Check ground connection
No Image On Screen
• Verify camera is on correctcamera input
• Verify cable is connected tomonitor
• Verify camera is connected tocable
• Connect known workingcamera and cable to monitor.
• Verify Blue trigger is receivingpower
Audio on Camera
• Verify chosen camera has audio• Verify volume setting
• Confirm that the Blue audiotrigger is connected to 12v+
22
Warranty
One Year WarrantyBuyers Products Company, Inc. warrants this product against material defectsfor a period of one year from date of purchase. We reserve the right to repairor replace any such defective unit at our sole discretion. Buyers ProductsCompany, Inc. is not responsible for a defect in the system as a result of mis-use, improper installation, damage or mishandling of the electronic compo-nents. Buyers Products Company, Inc. is not responsible for consequentialdamages of any kind.This warranty is void if: defects in materials or workmanship or damages re-sult from repairs or alterations which have been made or attempted by oth-ers or the unauthorized use of nonconforming parts; the damage is due tonormal wear and tear, this damage is due to abuse, improper maintenance,neglect or accident; or the damage is due to use of the Buyers ProductsCompany, Inc. system after partial failure or use with improper accessories.Warranty PerformanceDURING THE ABOVE WARRANTY PERIOD, SHOULD YOUR Buyers Products CompanyPRODUCT EXHIBIT A DEFECT IN MATERIAL OR WORKMANSHIP, SUCH DEFECT WILL BEREPAIRED WHEN THE COMPLETE Buyers Products Company, INC. PRODUCT IS RE-TURNED, POSTAGE PREPAID AND INSURED, TO Buyers Products Company, INC. OTHERTHAN THE POSTAGE AND INSURANCE REQUIREMENT, NO CHARGE WILL BE MADE FORREPAIRS COVERED BY THIS WARRANTY.
Warranty DisclaimersNO WARRANTY, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, OTHER THE ABOVEWARRANTY IS MADE WITH REGARD TO THIS Buyers Products Company, INC. BuyersProducts Company, INC. DISCLAIMS ANY IMPLIED WARRANTY OR MERCHANT-ABILITY ORFITNESS FOR A PARTICULAR USE OR PURPOSE AND ALL OTHER WARRANTIES IN NOEVENT SHALL Buyers Products Company. INC. LIABLE FOR ANY INCIDENTAL, SPECIAL,CONSEQUENTIAL, OR PUNITIVE DAMAGES OR FOR ANY COSTS, ATTORNEY FEES, EX-PENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO,FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANYCLAIMS FOR LOSS OF PROFITS.
23
DisclaimerBuyers Products Company and/or its affiliates does not guarantee or prom-ise that the user of our systems will not be in/part of an accident or other-wise not collide with an object and/or person. Our systems are not asubstitute for careful and cautious driving or for the consistent adherenceto all applicable traffic laws and motor vehicle safety regulations. The Buy-ers Products Company products are not a substitute for rearview mirrors orfor any other motor vehicle equipment mandated by law. Our camera sys-tems have a limited field of vision and do not provide a comprehensive viewof the rear or side area of the vehicle. Always make sure to look around yourvehicle and use your mirrors to confirm rearward clearance and that yourvehicle can maneuver safely. Buyers Products Company and/or its affiliatesshall have no responsibility or liability for damage and/or injury resultingfrom accidents occurring with vehicles having some of Buyers ProductsCompany products installed and Buyers Products Company and/or its affili-ates, the manufacturer, distributor and seller shall not be liable for any in-jury, loss or damage, incidental or consequential, arising out of the use orintended use of the product. In no event shall Buyers Products Companyand/or its affiliates have any liability for any losses (whether direct or indi-rect, in contract, tort or otherwise) incurred in connection with the systems,including but not limited to damaged property, personal injury and/or loss oflife. Neither shall Buyers Products Company and/or its affiliates have any re-sponsibility for any decision, action or inaction taken by any person in re-liance on Buyers Products Company systems, or for any delays, inaccuraciesand/or errors in connection with our systems functions.
Disclaimer
9049 Tyler Blvd. • Mentor, Ohio 44060Phone (440) 974-8888 • Fax 800-841-8003
Email: [email protected]