waterproofing cad details typical waterproofing … · 1) waterproofing should be fully bonded and...

20
WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING CONNECTIONS

Upload: others

Post on 17-Jul-2020

29 views

Category:

Documents


3 download

TRANSCRIPT

Page 1: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

WATERPROOFING CAD DETAILSTYPICAL WATERPROOFING CONNECTIONS

Page 2: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

2

WATERPROOFING DETAILSTypical Waterproofing Connection Details

Page 3: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

3

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

THE CRITICAL AREAS OF WATERPROOFING

These are the most common areas where waterproofing can fail. To reduce the risks significantly;1) Waterproofing should be fully bonded and continuous.2) Compatibility is crucial. Quality is crucial.3) Get expert input early – Sika has over 100 years of global waterproofing expertise on tap.

Vers

ion:

021

7

BELOW GROUND WATERPROOFING TO BS:8012/2009

Balcony waterproofing over non-habitable space connection to facade

Balcony / podium deck waterproofing over habitable space connection to facade

Masonry walls to toe footing detail connection

Basement to deck connection

Waterproof window reveal and air seal connection

Facade baffle & airseal connection

Basement waterproofing to facade connection

Page 4: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

4

WATERPROOFING DETAILSTypical Waterproofing Connection Details

CRITICAL WATERPROOFING CONNECTION DETAILS

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018BlackSeal Elastic / DPM

Sika Blackseal ProtectionSheet or 50mm thick EPS fixedinto position with tape

Minimum 2 coats of SikaBlackseal Elastic applied toprimed substrateNote:Trim this leg of SikaProof Aedge sheet to suit

200mm wide SikaDeckweb Mesh

SikaProof Atape 150

100mm perforated drainage pipe wrappedin geotextile filter fabric - check engineersdetail

DPM500 mm

SikaProof A edge sheet

100mm overlap, adhered to selvedge ofSikaProof A edge sheet

Note:Highly porous blocks anduneven masonry walls shall bebagged with Sika MonoTopFairing Coat or otherappropriate cement basedmortar.

Note:Wall must be flush with slab. If this cannot beachieved then any misalignment must be made flush.

Sika BlackSeal Elastic - Masonry Walls - Wall to Floor Scale 1:5Drawing no: 14

50mm site concrete

100 mm

150

mm

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Sika BlackSeal Elastic / SikaProof A edge sheet

100 mm

Precast concrete panel

Granular free drainage backfill

Sika BlackSeal ProtectionSheet or 50mm thick EPS fixed

into position with tape

Minimum 2 coats of SikaBlackSeal Elastic applied to

primed substrate

SikaProof A Tape 150

100mm perforated drainagepipe wrapped in geotextile

filter fabric - refer engineersdetail

SikaSwell-P Profile2010 H

SikaGrout-212

100mm overlapadhered to selvedge ofSikaProof A edge sheet

DPM

150

mm

100m

m10

0mm

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018BlackSeal Elastic / SikaProof A

Sika BlackSeal Protection Sheet or 50mmthick EPS fixed into position with tape

100mm perforated drainagepipe wrapped in geotextilefilter fabric - refer engineersdetail

DPM

SikaProof A edge sheet

Sika BlackSeal Elastic applied fullyonto SikaProof A Tape 150

50mm site concrete

SECTION

Note:Highly porous blocks anduneven masonry walls shall bebagged with Sika MonoTopFairing Coat or otherappropriate cement basedmortar.

Sand/cement/BlackSeal Elastic mortar25mm angle fillet

Minimum 2 coats of Sika BlackSealElastic applied to primed substrate

200

mm

min

.

500 mm

150

mm

min

.

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaProof Bentonite/Sikalastic -152

4mm Sikalastic-152 taken 150mm aboveground level and lapped 150mm behindSikaProof Bentonite with 40mm wide strip ofSikaProof Bentonite paste in the lap15

0 m

m15

0 m

m

GROUND LEVEL

Sikaflex-11 FC

25mmx2mm aluminum termination bar fixed atmax. 300mm centres with mechanical fastener

SikaProof Bentonite preapplied to formwork inpre-cast yard

Minimum 6mm Coreflute board protection

Granular free drainage backfill

SECTION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Sika Car Park DeckSikaProof P

2 Take Sika Carpark Deck System 150mm onto Sikafloor-400 N Elastic

1 Apply a 300mm wide strip of Sikafloor-400 N Elastic

Sika Carpark Deck System

3 Terminate SikaProof P 150mm onto Sikafloor-400 N Elastic

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Sika Car Park DeckSikaProof Bentonite

Apply a 300mm wide strip ofSikafloor-400 N Elastic to thevertical concreteStage 1

Terminate SikaProof Bentonite ontothe Sikafloor-400 N Elastic 150mm

Stage 2

150

mm

Take the Sika Car Park Deckdown 150mm onto thepreapplied Sikafloor-400 NElastic

Stage 3

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Typical Overlap DetailSikaProof A / DPM

SikaProof A lapped underneathdpm bonded to selvedge

Likely to require site concrete tosupport this junction

SikaSwell - A Profile

If DPM exists, cut back to astraight edge

300 mm

SikaProof A-12

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Typical Overlap Detail SikaProof A/SikaRoof MTC

SikaRoof MTC

150mm wide strip ofSikaProof P

SikaProof A

SWOD 01 · Page 6 SWOD 02 · Page 7 SWOD 03 · Page 8 SWOD 04 · Page 9

SWOD 05 · Page 10 SWOD 06 · Page 11 SWOD 07 · Page 12 SWOD 08 · Page 13

Page 5: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

5

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaProof Bentonite / Sarnafil

Note:Protect out side withcoreflute before backfilling.Laps to be glued.

Hot air weld

Sarnafil G410-20L Felt loose laid

Sarnafil G410-20L

200mm cover strip of Sarnafil G410-20Lwelded 40mm at sides and ends

SikaProof Bentonite

Lap Sarnafil 300mm min.past top edge of Bentonite

Bentonite trimmed 100mmfrom top of slab10

0mm

Sarnafil U-bar 100mm from concreteedge to allow room for tile pedestal

Termination bar Type IIFully bond vertical section of SarnafilG410-20L Felt with Sarnacol 808

300m

m

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaRoof MTC/SikaProof Bentonite

Second application of SikaRoof-MTC 22reinforced with Sika Reemat and taken

150mm onto the SikaProof Bentonite

SikaProof Bentonite terminated atground level

SikaProof Bentonite overlappingfirst application of SikaRoof-MTC 22

by 150mm

1. Apply SikaRoof MTC

2. Apply SikaProof Bentonite3. Apply SikaRoof MTC

If Bentonite is pre-applied, ensuretop 150mm is left debonded.

SWOD 09 · Page 14 SWOD 10 · Page 15 SWOD 11 · Page 16

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaProof A onto Sarnafil G410 & S327

Sarnafil G410-10L heat welded ontoDilatec ER350 Tape

Dilatec ER350 tape adhered ontoSikaProof A with Sikadur-31

SikaProof A

Sika balcony deck waterproofing and door threshold joint sealingfor concrete decks over habitablespace Scale 1:5

45 Deg. chamfer to screed

Roof membrane extends below window frame Timber threshold board

Sikaflex / SikaHyflex facadesealant air seal backed by a PEF rod to perimeter of trim cavity compatible with balcony waterproofing membrane

Timber threshold board

Roof membrane fixed below window frame

If build is less than 40mm screed must be bonded with emulsion 93 sand & cement slurry

Linear drainage grille along length of door opening. Alternatively, a 12mm gap between deck and sill is required

Tile decking on deck jacks on square of Sarnafil G410-20L FELT

Sill tray & packers

Sikaflex / SikaHyflex facade sealant air seal backed by a PEF rod to perimeter of trim cavity compatible with balcony waterproofing membrane

Sika Screed 1 or Sikascreed binder

Roof screed to fall to roof gullies, fall 1.5 degrees (min.)

Sill tray

Packers

Sill to provide minimum 10mm overhang, with 5mm drainage clearance (vertically & horizontally)

Liquid applied or sheet roof membrane to be extended onto slab beneath door sill

Roof membrane SikaRoof MTC 22or Sarnafil G410-20L FELT fully bonded

SWOD 12 · Page 17

Sikalastic - 152 beneath window / door to run along the entire sill and down the external face of the sill and min. 40mm up the jambs

Sill profile to provide min. 10mm overhang, with 5mm drainage clearance (vertical and horizontal)

Sika concrete masonry reveal waterproofing and window joint sealing detail Scale 1:5

Weathertightness system

Window frame fixed to blockwork, and packed as required

Drip edge formed from plaster or pvc angle

Continuous head and jamb seal Sikaflex / SikaHyflex facade sealant backed by a PEF rod

Plaster or coating finish

Sikaflex / SikaHyflex facade sealant air seal backed by a PEF rod to perimeter of trim cavity

Sikaflex / SikaHyflex facade sealant air seal backed by a PEF rod to perimeter of trim cavity

Sikalastic - 152 waterproof coating or membrane continuous at head and jambs

SWOD 13 · Page 18 SWOD 14 · Page 19

TECHNICAL DRAWINGBalcony deck waterproofing and door threshold joint sealing for concrete decks over non-habitable space

2

015

Sika

(NZ)

Ltd

The information contained herein and any other advice are given in good faith based on Sika’s current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika’s recommendations. The information only applies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika’s Technical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Technical Drawing NZ · APAC Balcony deck waterproofing and door threshold joint sealing for concrete decks over non-habitable space Oct 2015, Version 1015

Sika (NZ) LimitedSealing & Bonding · Waterproofing85-91 Patiki Road, AvondaleAuckland 1026New Zealand

Phone: 0800 745 269Fax: 0800 745 232Mail: [email protected]

Page 6: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

6

WATERPROOFING DETAILSTypical Waterproofing Connection Details

Sika Car Park DeckSikaProof P

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Sika Car Park DeckSikaProof P

2 Take Sika Carpark Deck System 150mm onto Sikafloor-400 N Elastic

1 Apply a 300mm wide strip of Sikafloor-400 N Elastic

Sika Carpark Deck System

3 Terminate SikaProof P 150mm onto Sikafloor-400 N Elastic

Page 7: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

7

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Sika Car Park DeckSikaProof Bentonite

Apply a 300mm wide strip ofSikafloor-400 N Elastic to thevertical concreteStage 1

Terminate SikaProof Bentonite ontothe Sikafloor-400 N Elastic 150mm

Stage 2

150

mm

Take the Sika Car Park Deckdown 150mm onto thepreapplied Sikafloor-400 NElastic

Stage 3

Page 8: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

8

WATERPROOFING DETAILSTypical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Typical Overlap DetailSikaProof A / DPM

SikaProof A lapped underneathdpm bonded to selvedge

Likely to require site concrete tosupport this junction

SikaSwell - A Profile

If DPM exists, cut back to astraight edge

300 mm

SikaProof A-12

Page 9: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

9

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Typical Overlap Detail SikaProof A/SikaRoof MTC

SikaRoof MTC

150mm wide strip ofSikaProof P

SikaProof A

Page 10: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

10

WATERPROOFING DETAILSTypical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018BlackSeal Elastic / DPM

Sika Blackseal ProtectionSheet or 50mm thick EPS fixedinto position with tape

Minimum 2 coats of SikaBlackseal Elastic applied toprimed substrateNote:Trim this leg of SikaProof Aedge sheet to suit

200mm wide SikaDeckweb Mesh

SikaProof Atape 150

100mm perforated drainage pipe wrappedin geotextile filter fabric - check engineersdetail

DPM500 mm

SikaProof A edge sheet

100mm overlap, adhered to selvedge ofSikaProof A edge sheet

Note:Highly porous blocks anduneven masonry walls shall bebagged with Sika MonoTopFairing Coat or otherappropriate cement basedmortar.

Note:Wall must be flush with slab. If this cannot beachieved then any misalignment must be made flush.

Sika BlackSeal Elastic - Masonry Walls - Wall to Floor Scale 1:5Drawing no: 14

50mm site concrete

100 mm

150

mm

Page 11: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

11

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018Sika BlackSeal Elastic / SikaProof A edge sheet

100 mm

Precast concrete panel

Granular free drainage backfill

Sika BlackSeal ProtectionSheet or 50mm thick EPS fixed

into position with tape

Minimum 2 coats of SikaBlackSeal Elastic applied to

primed substrate

SikaProof A Tape 150

100mm perforated drainagepipe wrapped in geotextile

filter fabric - refer engineersdetail

SikaSwell-P Profile2010 H

SikaGrout-212

100mm overlapadhered to selvedge ofSikaProof A edge sheet

DPM

150

mm

100m

m10

0mm

Page 12: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

12

WATERPROOFING DETAILSTypical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018BlackSeal Elastic / SikaProof A

Sika BlackSeal Protection Sheet or 50mmthick EPS fixed into position with tape

100mm perforated drainagepipe wrapped in geotextilefilter fabric - refer engineersdetail

DPM

SikaProof A edge sheet

Sika BlackSeal Elastic applied fullyonto SikaProof A Tape 150

50mm site concrete

SECTION

Note:Highly porous blocks anduneven masonry walls shall bebagged with Sika MonoTopFairing Coat or otherappropriate cement basedmortar.

Sand/cement/BlackSeal Elastic mortar25mm angle fillet

Minimum 2 coats of Sika BlackSealElastic applied to primed substrate

200

mm

min

.

500 mm

150

mm

min

.

Page 13: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

13

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaProof Bentonite/Sikalastic -152

4mm Sikalastic-152 taken 150mm aboveground level and lapped 150mm behindSikaProof Bentonite with 40mm wide strip ofSikaProof Bentonite paste in the lap15

0 m

m15

0 m

m

GROUND LEVEL

Sikaflex-11 FC

25mmx2mm aluminum termination bar fixed atmax. 300mm centres with mechanical fastener

SikaProof Bentonite preapplied to formwork inpre-cast yard

Minimum 6mm Coreflute board protection

Granular free drainage backfill

SECTION

Page 14: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

14

WATERPROOFING DETAILSTypical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaProof Bentonite / Sarnafil

Note:Protect out side withcoreflute before backfilling.Laps to be glued.

Hot air weld

Sarnafil G410-20L Felt loose laid

Sarnafil G410-20L

200mm cover strip of Sarnafil G410-20Lwelded 40mm at sides and ends

SikaProof Bentonite

Lap Sarnafil 300mm min.past top edge of Bentonite

Bentonite trimmed 100mmfrom top of slab10

0mm

Sarnafil U-bar 100mm from concreteedge to allow room for tile pedestal

Termination bar Type IIFully bond vertical section of SarnafilG410-20L Felt with Sarnacol 808

300m

m

Page 15: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

15

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaRoof MTC/SikaProof Bentonite

Second application of SikaRoof-MTC 22reinforced with Sika Reemat and taken

150mm onto the SikaProof Bentonite

SikaProof Bentonite terminated atground level

SikaProof Bentonite overlappingfirst application of SikaRoof-MTC 22

by 150mm

1. Apply SikaRoof MTC

2. Apply SikaProof Bentonite3. Apply SikaRoof MTC

If Bentonite is pre-applied, ensuretop 150mm is left debonded.

Page 16: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

16

WATERPROOFING DETAILSTypical Waterproofing Connection Details

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaProof A onto Sarnafil G410 & S327

Sarnafil G410-10L heat welded ontoDilatec ER350 Tape

Dilatec ER350 tape adhered ontoSikaProof A with Sikadur-31

SikaProof A

Page 17: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

17

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

Sika balcony deck waterproofing and door threshold joint sealingfor concrete decks over habitablespace Scale 1:5

45 Deg. chamfer to screed

Roof membrane extends below window frame Timber threshold board

Sikaflex / SikaHyflex facadesealant air seal backed by a PEF rod to perimeter of trim cavity compatible with balcony waterproofing membrane

Timber threshold board

Roof membrane fixed below window frame

If build is less than 40mm screed must be bonded with emulsion 93 sand & cement slurry

Linear drainage grille along length of door opening. Alternatively, a 12mm gap between deck and sill is required

Tile decking on deck jacks on square of Sarnafil G410-20L FELT

Sill tray & packers

Sikaflex / SikaHyflex facade sealant air seal backed by a PEF rod to perimeter of trim cavity compatible with balcony waterproofing membrane

Sika Screed 1 or Sikascreed binder

Roof screed to fall to roof gullies, fall 1.5 degrees (min.)

Sill tray

Packers

Sill to provide minimum 10mm overhang, with 5mm drainage clearance (vertically & horizontally)

Liquid applied or sheet roof membrane to be extended onto slab beneath door sill

Roof membrane SikaRoof MTC 22or Sarnafil G410-20L FELT fully bonded

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaRoof MTC/SikaProof Bentonite

Second application of SikaRoof-MTC 22reinforced with Sika Reemat and taken

150mm onto the SikaProof Bentonite

SikaProof Bentonite terminated atground level

SikaProof Bentonite overlappingfirst application of SikaRoof-MTC 22

by 150mm

1. Apply SikaRoof MTC

2. Apply SikaProof Bentonite3. Apply SikaRoof MTC

If Bentonite is pre-applied, ensuretop 150mm is left debonded.

Sika balcony deck waterproofing & door threshold joint sealing for concrete decks over habitable space

Aug 2014

Page 18: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

18

WATERPROOFING DETAILSTypical Waterproofing Connection Details

Sikalastic - 152 beneath window / door to run along the entire sill and down the external face of the sill and min. 40mm up the jambs

Sill profile to provide min. 10mm overhang, with 5mm drainage clearance (vertical and horizontal)

Sika concrete masonry reveal waterproofing and window joint sealing detail Scale 1:5

Weathertightness system

Window frame fixed to blockwork, and packed as required

Drip edge formed from plaster or pvc angle

Continuous head and jamb seal Sikaflex / SikaHyflex facade sealant backed by a PEF rod

Plaster or coating finish

Sikaflex / SikaHyflex facade sealant air seal backed by a PEF rod to perimeter of trim cavity

Sikaflex / SikaHyflex facade sealant air seal backed by a PEF rod to perimeter of trim cavity

Sikalastic - 152 waterproof coating or membrane continuous at head and jambs

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaRoof MTC/SikaProof Bentonite

Second application of SikaRoof-MTC 22reinforced with Sika Reemat and taken

150mm onto the SikaProof Bentonite

SikaProof Bentonite terminated atground level

SikaProof Bentonite overlappingfirst application of SikaRoof-MTC 22

by 150mm

1. Apply SikaRoof MTC

2. Apply SikaProof Bentonite3. Apply SikaRoof MTC

If Bentonite is pre-applied, ensuretop 150mm is left debonded.

Sika balcony deck waterproofing & door threshold joint sealing for concrete decks over habitable space

Page 19: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

19

WATERPROOFING DETAILS

Typical Waterproofing Connection Details

TECHNICAL DRAWINGBalcony deck waterproofing and door threshold joint sealing for concrete decks over non-habitable space

2

015

Sika

(NZ)

Ltd

The information contained herein and any other advice are given in good faith based on Sika’s current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika’s recommendations. The information only applies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika’s Technical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Technical Drawing NZ · APAC Balcony deck waterproofing and door threshold joint sealing for concrete decks over non-habitable space Oct 2015, Version 1015

Sika (NZ) LimitedSealing & Bonding · Waterproofing85-91 Patiki Road, AvondaleAuckland 1026New Zealand

Phone: 0800 745 269Fax: 0800 745 232Mail: [email protected]

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) Ltd

PO Box 19192

Auckland 1746

New Zealand.

Ph. 0800 745 269

www.sika.co.nz

May 2018SikaRoof MTC/SikaProof Bentonite

Second application of SikaRoof-MTC 22reinforced with Sika Reemat and taken

150mm onto the SikaProof Bentonite

SikaProof Bentonite terminated atground level

SikaProof Bentonite overlappingfirst application of SikaRoof-MTC 22

by 150mm

1. Apply SikaRoof MTC

2. Apply SikaProof Bentonite3. Apply SikaRoof MTC

If Bentonite is pre-applied, ensuretop 150mm is left debonded.

Sika balcony deck waterproofing & door threshold joint sealing for concrete decks over non-habitable space

Oct 2015

Page 20: WATERPROOFING CAD DETAILS TYPICAL WATERPROOFING … · 1) Waterproofing should be fully bonded and continuous. 2) Compatibility is crucial. Quality is crucial. 3) Get expert input

FOR MORE Sika® INFORMATION:

WHO WE ARESika AG, Switzerland, is a globally active specialty chemicals company. Sika supplies the building and construction industry as well as manufacturing industries (automotive, bus, truck, rail, solar and wind power plants, façades). Sika is a leader in processing materials used in sealing, bonding, damping, reinforcing and protecting loadbearing structures. Sika’s product lines feature high quality concrete admixtures, specialty mortars, sealants and adhesives, damping and reinforcing materials, structural strengthening systems, industrial flooring as well as roofing and waterproofing systems.

© S

ika

(NZ

) Ltd

| V

ersi

on N

o.: 1

018

(rep

lace

s02/

17)