water quality products - pentair · 220 uvt meter 221 turbidity meter 222 calibration solutions 224...

Online Orders: PentairAES.com I Phone Orders and Tech Advice: 877.347.4788

PRODUCTS194 Dissolved Oxygen Meters201 ORP Meters202 Total Dissolved Gas Pressure Meters204 pH Meters206 Conductivity Meters208 Salinity Meters210 Multiparameter Meters218 Photometers219 Colorimeter220 UVT Meter221 Turbidity Meter222 Calibration Solutions224 Test Kits/Test Strips

WATER QUALITY


194 SECTIONProducts / Products / Products

Y60020

YSI® is a registered trademark of YSI, Inc.

Meter, probe and cable sold separately, or order a kit that includes all this plus a carrying case.

SYSTEM SPECS (METER, PROBE & CABLE)

DISSOLVED OXYGEN (% SATURATION)Range: 0–500% air saturationAccuracy: ±2% of the reading or ±2% air saturationResolution: 1% or 1% air saturation

DISSOLVED OXYGEN (MG/L)Range: 0–50 mg/L.Accuracy: ±2% of the reading or ± 0.2 mg/LResolution: 0.01 or 0.1 mg/L

TEMPERATURERange: -5–55º C (D.O. compensation range -5–45º C)Accuracy: ± 0.3º CResolution: 0.1° C.

BAROMETERRange: 400 to 999.9 mmHg. Accuracy: ±5 mmHg (within ±5° C of calibration temp)Resolution: 0.1 mmHg

YSI® Instrument RepairWhether it is a yearly checkup or the complete replacement of a circuit board, you can count on us to provide accurate, economical and timely service. This applies to all YSI® meters that we carry, whether or not they were purchased from us. We honor all factory warranties, we stock a full inventory of replacement parts and our labor rates are significantly lower than the amount charged by most other YSI® repair facilities.To obtain an estimate or to send a meter for repair, call us at 877-347-4788 for a Return Authorization Number (RA#). This number will allow us to identify your package and follow your instructions. You’ll also need to fill out and send in our Return Form and Cleaning Certificate.

Low Labor RatesOur electronics technicians are the best and our turnaround time is fast (1–2 weeks). If you wish to expedite turnaround, we can do that for a small fee. There is no charge for warranty repairs.Nonwarranty repair estimates typically require between 60 and 120 minutes before a repair cost quotation can be made. Therefore, we will have to charge for nonwarranty repair quotes, one-hour minimum.changes without notice.

3-YEAR METERWARRANTY

YSI® PRO20 DISSOLVED OXYGEN METERDesigned specifically for aquaculture, the YSI Pro20 dissolved oxygen meter is a rugged, user-friendly instrument for dissolved oxygen measurement. IP-67 waterproof and rubber over molded case, and 1-meter drop tests ensure the instrument remains in your hands to provide years of sampling even in the harshest field conditions. Choose a D.O. sensor that best meets your needs. Fast response times with the Polarographic or Galvanic dissolved oxygen sensors allow you to complete your sampling routine quickly. The long life of the Polarographic sensor saves time and money and reduces your overall cost. The Galvanic sensor enables you to start sampling immediately without a warm-up period. Meters measure 3.25” x 8.5” x 2.25” and weigh 1 lb. Use 2 C batteries (included). Three-year warranty on meters, two years on cables and one year on probes. Internal barometer for highest accuracy• Large, easy-to-read, backlit display and keypad• Fast cal routine allows easy calibrations with the press of a button• Stores 50 data sets• Rugged, weighted probe assembly• View display with polarized sunglasses on and all lighting conditions• Fastest response in 8 seconds with standard membrane• Multiple languages include English, Spanish, French and German• Rubber over mold case for durability• Automatic barometric pressure and temperature compensation• User replaceable sensors and cables• Direct replacement for YSI Model 85

Galvanic vs Polarographic Sensors

Galvanic sensors do not require a warm-up period. They are ready for immediate use after being powered on.Polarographic sensors require warm up time before use. The shelf life for Polarographic sensors is theoretically longer than Galvanic sensors.

MODEL EACH

KITSY603170 METER, GALVANIC D.O. PROBE, 4M CABLE, CARRY CASE $1,095.00 Y603171 METER, POLAROGRAPHIC D.O. PROBE, 4M CABLE, CARRY CASE 1,095.00

METER ONLYY60020 PRO20 D.O. METER $559.99

PROBESY6202 GALVANIC D.O. $179.99 Y6203 POLAROGRAPHIC D.O. 179.99

CABLES (INCLUDES TEMP SENSOR & WEIGHTED REMOVAL BOARD)Y624C 4 METER $264.99 Y6210C 10 METER 314.99 Y6220C 20 METER 374.99 Y6230C 30 METER 474.99

REPLACEMENT MEMBRANE KITSY5908 D.O. CAP KIT W/KCL (FOR POLAROGRAPHIC D.O. PROBES ONLY) $59.99 Y5913 D.O. CAP KIT W/NACL (FOR GALVANIC D.O. PROBES ONLY) 59.99

194 WATER QUALITYDissolved Oxygen Meter


SECTIONProducts / Products / Products

195

YSI® and ProODO® are registered trademarks of YSI, Inc

YSI® PROODO® OPTICAL DISSOLVED OXYGEN METERThe YSI ProODO® is rugged, easy to use handheld optical dissolved oxygen meter designed for sampling applications. With many benefits over traditional D.O. technologies, the ODO (Optical Dissolved Oxygen) luminescent sensor has no flow dependence, making it the perfect choice for applications where stirring is difficult or undesirable. This also reduces the possibility of operator error, ensuring high quality data. Unit is resistant to probe fouling and interferences from hydrogen sulfide and other gases. The smart digital ODO probe stores calibration data so probes can be interchanged between instruments without recalibration. Stores 5,000 data sets, and USB connection allows interaction with Data Manager software (included). Supports English, Spanish, German, Italian, Norwegian, Portuguese and French. IP67-rated case. Military spec connectors and field tested cables, 100 folders and site lists for logging data with user defined fields, and a graphic display with detailed Help visible with polarized sunglasses. Salinity input rate 0–70 ppt. Runs on two C batteries. 8.5" L x 3.25" W x 2.25" H, weighs 1 lb. Three-year warranty on instrument, two years on cable and probe.

3-YEAR METER WARRANTY

Meter, probe & cable sold separately, or order a kit that includes all this plus a carrying case.

Y6262

MODEL EACH

KITY603192 METER, PROBE, 4M CABLE, CARRY CASE $1,475.00

METER ONLYY6262 PROODO METER $724.99

CABLES WITH PROBEY62504 4 METER CABLE WITH ODO PROBE $674.99 Y625010 10 METER CABLE WITH ODO PROBE 749.99 Y625020 20 METER CABLE WITH ODO PROBE 809.99

REPLACEMENT PARTY6263 REPLACEMENT SENSING ELEMENT $99.99

ACCESSORIESY603069 BELT CLIP $29.39 Y603075 SOFT SIDED CARRYING CASE 124.99 Y603074 HARD SIDED CARRYING CASE 284.99

195WATER QUALITYDissolved Oxygen Meter


196 WATER QUALITYDissolved Oxygen Meters

YDO200A

Y2004

YSI® and EcoSense® are registered trademarks of YSI, Inc

SYSTEM SPECS

RANGES O2 0–20 mg/LSat. 0–200%Temp. -6–46° C

RESOLUTION O2 0.01 mg/LSat. 0.10%Temp. 0.1° C

ACCURACY O2 ± 0.2%Sat. ±2%Temp. ± 0.3° C

MODEL EACH

YDO200A DO METER ONLY $289.99YDO200A-4 DO METER, PROBE, 4M CABLE & CASE 629.99Y2004 4-METER CABLE W/PROBE ONLY 309.99Y20010 10-METER CABLE W/PROBE ONLY 329.99Y5908 REPL. MEMBRANES W/KCL, POLAROGRAPHIC 59.99Y200-BOD BIOCHEMICAL OXYGEN DEMAND PROBE 684.99

ECOSENSE® DO200A DISSOLVED OXYGEN METERThe EcoSense D0200A is an economical version of the quality and results expected from YSI®. The rugged housing is IP67 splash resistant, and the large LCD simultaneously displays ppm or percent saturation and temperature (ºC only). Easy-to-replace, screw-on cap membranes have a fast response time and are low-stirring dependent. Nine-volt battery life is typically 500 hours; indicator warns when battery level is low. Detachable probe and cable assembly sold separately below. One-year warranty on meter, six-month warranty on probe.

Cable & Probe Sold Separately

ECOSENSE® ODO200 OPTICAL DO & TEMPERATURE METERThe EcoSense ODO200 handheld dissolved oxygen meter uses optical technology and provides the most accurate data in the most affordable format. Features an easy-to-use interface, one-hand operation, IP67 waterproof case, and low cost of ownership over the life of the product. The ODO200 simultaneously measures dissolved oxygen % and mg/L and (optical) temperature. One-year warranty on meter, cables and sensor cap. • Automatic temperature compensation• Manual input for salinity and pressure compensation• Low battery indicator with 100 hour battery life• Auto shutoff function after 30 minutes of inactivity• 50 data set reviewable memory

Optical benefits include• No stirring requirement• No warm-up time• No electrolyte solutions• No electrode maintenance• No membranes• No interferences from gases such as hydrogen sulfide

MODEL EACH

Y606329 OPTICAL DO/TEMP METER ONLY $329.99Y606327 1-METER CABLE WITH DO/TEMP PROBE ONLY 589.99Y606328 4-METER CABLE WITH DO/TEMP PROBE ONLY 599.99Y606304 10-METER CABLE WITH DO/TEMP PROBE ONLY 674.99Y606326 SENSOR CAP KIT 119.99Y606330 HARD PLASTIC CARRYING CASE WITH FOAM INSERT 39.99


Y606329

SYSTEM SPECS

RANGES O2 0–20 mg/LSat. 0–200%Temp. 0-50° C

RESOLUTION O2 0.01 mg/LSat. 0.10%Temp. 0.1° C

ACCURACY O2 ± 1.5%Sat. ±1.5%Temp. ± 0.3° C


WATER QUALITYTech Talk

197

DISSOLVED OXYGEN METERS AND PROBES

MODEL MANUFACTURER PARAMETERSD.O. RANGE

(PPM OR MG/L) ACCURACYRESOLUTION

(PPM OR MG/L) WATERPROOF BACKLIT DISPLAY

CONNECTORIZED CABLE/PROBE

WARRANTY METER/PROBE

OXYGEN MEMORY/RS232 PROBE TYPE

DO62 American Marine

D.O. Only 0–20.0 ±0.2 ppm 0.1 No No Yes 2-yr/2-yr No Polarographic

YDO200A YSI* D.O., Temp 0–20.0 ±0.2% 0.1 No No Yes 1-yr/6-mo No Polarographic

Y55D YSI* D.O., Temp 0–20.0 ±0.25 .01 No Yes Yes 2-yr/1-yr No Polarographic

Y52 YSI* D.O., Temp 0–19.99 ±0.02 .01 No No Yes 2-yr/6-mo Yes Polarographic

Y58 YSI* D.O., Temp 0–19.99 ±0.03 .01 No No Yes 2-yr/6-mo No Polarographic

Y550A YSI* D.O., Temp 0–50.00 ±0.03 .01 Yes Yes No 3-yr/6-mo No Polarographic

Y60020 YSI* D.O., Temp, mmH

0–50.00 ±2.0% .01 or 0.1 Yes Yes Yes 3-yr/2-yr No Polaro./Galv.

850048 Sper D.O., Temp 0–19.99 ±1.5 .01 No Yes Yes 5-yr/6-mo Yes Polarographic

1OXHM053 OxyGuard D.O., Temp, % Sat

0-60.0 ±1.0% 0.1 Yes Yes No 1 yr Yes, data log 3,000 sets

Galvanic

Y605120 YSI D.O., Temp, PH, ORP (REDOX)

0 TO 50 ±2.0% 0.01 OR 0.1 Yes Yes Yes 3-yr/1-yr 50 data sets Polaro./Galv.

Y606329 EcoSense Optical D.O., Temp.

0 to 20 ±1.5% 0.01 Yes Yes Yes 1-yr 50 data set Optical

Y6262 YSI* Optical D.O., Temp.

0 TO 50 ± 1.0% 0.01 OR 0.1 Yes Yes Yes 3-yr/2-yr 5000 data sets Optical

Y6052030 YSI* D.O., Temp, Cond

0 to 50 ±2.0% 0.01 or 0.1 Yes Yes Yes 3-yr/1-yr 50 data sets Polaro./Galv.

*Pentair Aquatic Eco-Systems, Inc., is an authorized YSI Instruments Repair Center. Temp=Temperature. Sal=Salinity. ORP=Oxidation/Reduction Potential

TECH TALK 26

• Receive exclusive promotions and online shopping incentives• Learn about the industry with company articles • Find out about our workshops and educational courses• Be the first to know of new product announcements• Discover the benefits of being a Pentair customer & moreTo recieve our e-mails please visit:PentairAES.com/signup

NEWS & OFFERS



198 WATER QUALITYDissolved Oxygen Meter

OXYGUARD® HANDY POLARIS 1 DISSOLVED OXYGEN METERThe OxyGuard Handy Polaris is a portable D.O. meter that also measures % saturation, mg/L (ppm), temperature and has salinity compensation. Measurements are compensated for temperature and barometric pressure. The probe is galvanic type and fully field-serviceable. Has a large display with backlight and offers automatic calibration and a choice of language and units of measurement. Each unit is supplied with a detachable clip for easy attachment to a belt or clipboard. Battery life allows up to 1,400 hours of use from a single 9V battery. • Automatic calibration with stability check.• Compensates for changes in atmospheric pressure.• Automatic shutdown for power saving.

MODEL EACH

1OXHM053 HANDY POLARIS W/3-M (10') CABLE $859.991OXHM058 HANDY POLARIS W/8-M (25') CABLE 901.991OXHA013 HANDY MEMBRANE KIT, 10 PCS 17.191OXPA014 STANDARD ELECTROLYTE, 1 L 23.891OXPA015 STANDARD ELECTROLYTE, 250 ML 10.791OXPA016 STANDARD ELECTROLYTE, 50 ML 5.391OXHA010 MEMBRANE INSTALLATION TOOL 15.691OXHA007 PROBE PROTECTION CAP 31.691OXHA006 HANDY MEMBRANE CAP WITH MEMBRANE 66.19

SYSTEM SPECS

PARAMETERS ppm (mg/L), % saturation, temperature (ºC or ºF), salinity compensation.

SALINITY COMPENSATION 0–59 ppt salinity (manually set).

DISPLAY Large, easy to read graphical LCD display. Variable backlight.

ACCURACY, D.O. Depends on calibration accuracy. Typically better than +/- 1% of measured value +/- 1 digit within the standard measuring range.

PROBE TYPE Galvanic cell, self-polarizing, self-temperature compensating.

ACCURACY, TEMPERATURE +/- 0.2ºC

CABLE LENGTH Standard 3 m. REPEATABILITY Typically better than +/- 0.5% of measured range.

OPERATING CONDITIONS Probe: -5 to +45ºC, Meter: -20 to +60ºC

SELF-CHECK OF Probe function, meter function, cable, battery.

ENCAPSULATION (METER) Short-term immersion proof to max. 5-m depth.

STANDARD ACCESSORIES Membrane cap, membranes, electrolyte, cathode cleaning pad, storage pouch.

MEASURING RANGE 0–60.0 ppm (mg/L) and 0–600% saturation. Automatically compensated for temperature and barometric pressure. Manual salinity compensation. Temperature: -5 to +45ºC.

COMMITMENT TO CUSTOMER SATISFACTIONOur customers are our first priority.

We will provide extraordinary service to satisfy the needs of our customers.

We will deliver our products and services on time and error free, conforming to the requirements of our customers.

We strive to do it right the first time and eliminate any problem that prevents us from achieving complete customer satisfaction.

We thank you for your patronage.

Oxyguard® is a registered trademark of Thermal Gas Systems, Inc.



199WATER QUALITYDissolved Oxygen Meter

199

OXYGUARD® HANDY POLARIS 2 DISSOLVED OXYGEN METERThe OxyGuard Handy Polaris 2 is a portable dissolved oxygen (D.O.) meter that combines the features of the original Polaris with the convenience of data logging and data transfer capability. It measures % saturation, mg/L (ppm) and temperature and has salinity compensation. Measurements are compensated for temperature and barometric pressure. The galvanic probe is fully field- serviceable. Powered by a 9V battery. The Polaris 2 has a larger display with backlight and offers automatic calibration, and a choice of language and units of measurement. Includes a detachable clip for easy attachment to a belt or clipboard.

MODEL EACH

1OXHM073 HANDY POLARIS 2 W/3-M (10') CABLE $1,026.001OXHM075 HANDY POLARIS 2 W/8-M (25') CABLE 1,086.001OXHM074 USB LINK W/SOFTWARE (ONLY 1 REQUIRED FOR MULTIPLE UNITS) 266.691OXHA013 HANDY MEMBRANE KIT, 10 PCS 17.191OXPA014 STANDARD ELECTROLYTE, 1 L 23.891OXPA015 STANDARD ELECTROLYTE, 250 ML 10.791OXPA016 STANDARD ELECTROLYTE, 50 ML 5.391OXHA010 MEMBRANE INSTALLATION TOOL 15.691OXHA007 PROBE PROTECTION CAP 31.691OXHA006 HANDY MEMBRANE CAP WITH MEMBRANE 66.19

TECHNICAL ADVANTAGES

METER • Data logging and data transfer capability—over 3,000 sets of complete info (mg/L, % sat, temp, events, etc.). Polaris 2 only.

• Automatic calibration with stability check.• Automatic self-check of instrument.• Automatic check of cable and probe.• Compensates for changes in atmospheric pressure.• User-selectable language and main display parameter.• “On-screen” instructions.• 1,400 hours use from one 9V alkaline battery.• Illuminated display with variable intensity.• Automatic shutdown for power saving.

PROBE • Galvanic type.• Self-polarizing.• No warm-up time.• Fully temperature compensated.• Remarkably short response time.• Stores dry.• Excellent long-term stability.• Tough membrane.• No need for regular service or renovation.• Probe renovation easy and fast when needed.

EVERYTHING YOU NEED ON EVERY DEVICE

PentairAES.com



DO62

MODEL EACH

850048 DISSOLVED OXYGEN METER KIT* $396.69850048DO REPLACEMENT DISSOLVED OXYGEN PROBE** 114.49850048CS OPTIONAL CONDUCTIVITY/SALINITY PROBE** 87.19850048PH OPTIONAL PH PROBE ** 87.19

*Model 850048 replaces model 850041.**Not compatible with the old D.O. Meter Kit, model 850041.

850048

PINPOINT® DISSOLVED OXYGEN METERFeaturing a high-performance oxygen probe, this oxygen meter is a very good value. Temperature-compensated from 0–50°C (32–122ºF) with an accuracy of ± .2 ppm. Measures 0–20 ppm or percent saturation. Each meter comes with a replaceable probe on a 5' cable (the 12' extension cable cannot be submerged). Uses one 9V battery (included). Meter measures only 3" x 5". Meter, probe and cable are not waterproof nor water-resistant. The high performance DO62P probe is compatible with the old DO6 meters. Two-year warranty on the meter and probe (does not cover mishandling or water damage to meter).

MODEL EACH

DO62 OXYGEN METER $271.99DO62P REPLACEMENT PROBE 150.79DO62M MEMBRANE KIT* 26.19DO6A 12' EXTENSION CABLE 31.49PA12 OPTIONAL AC ADAPTER 12.79

*Electrolyte solution included.



DISSOLVED OXYGEN METER KIT The Sper Scientific DO Meter Kit measures dissolved oxygen to determine water quality in environmental testing, labs, industrial and municipal waste water, aquariums and fish hatcheries. Automatic temperature compensation as well as manual compensation for salinity and altitude (all factors directly affecting DO readings). Simultaneously displays dissolved oxygen (in % or mg/L) and temperature readings (in °C or °F). Review 99 data points readings directly on the large backlit LCD. Features simple one-button calibration to air. The electrolyte level is visible through the transparent galvanic probe with built-in temperature sensor. DO probe heads include built in membranes and screw on and off for easy replacement. Also functions as a pH and conductivity meter when used with the optional probes. Comes in a hard carrying case complete with pB (lead) free Galvanic DO probe with 9’ cable, two spare probe heads with membranes installed, electrolyte and four AAA batteries. Kit dimensions are 14¼" × 8¾" × 2¾" and weighs 14 ounces.Five-year warranty on meter, one year on probe.

SYSTEM SPECS

UNIT OF MEASURE RANGE RESOLUTION ACCURACY

DO 0~199.9% (0~30 mg/L)

0.1 ±3% fs ±1 d

PH (WITH OPTINAL PROBE) 2~12 0.01 ±0.1

CONDUCTIVITY (WITH OPTIONAL PROBE)

0~199.90~199.9 uS/cm

0~19.990~ 69.99 mS/cm

0.1 uS/cm1 uS/cm

0.01 mS/cm0.1 mS/cm

±1% fs ±1 d

SALINITY 0~10 ppt0~42 ppt (sea water)

0.01 ppt0.1 ppt

±1% fs ±1 d

TEMPERATURE ºF 23~176° F 0.1° F ±1° F

TEMPERATURE ºC 0~60° C 0.1° C ±0.5° C

DO6A

DO62P

DO62M

200 WATER QUALITYDissolved Oxygen Meters

Pinpoint® is a registered trademark of Dell Technology DBA American Marine, Inc.



201201WATER QUALITYORP Meters

ECOSENSE® ORP15A ORP/TEMPERATURE PENThe ECOSENSE® ORP15A takes absolute and relative ORP readings from -1,100 to +1,100 mV with this affordable instrument. Calibrate to an ORP standard! Use the Zobell ORP calibration solution (sold separately) to recalibrate at any time. It has replaceable electrodes, automatic temperature compensation and auto shut-off. Use the 50-set memory (absolute/relative mV, temperature and a date and time stamp) and “hold” feature that locks readings on-screen. Easy-to-understand menus and IP67 housing. Measures -10ºC to 100ºC (14 to 212ºF). Uses GAP-76 batteries (included). >200 hour battery life with low battery indicator. Pen is not waterproof nor water-resistant. One-year instrument warranty, six-month electrode warranty. Weighs 0.25 lb.

MODEL EACH

YORP15 ORP/TEMP PEN $166.99Y3628 ZOBELL ORP TEST SOLUTION 32.99Y605123 ORP REPLACEMENT ELECTRODE KIT 74.997021 ORP CALIBRATION SOLUTION, 240MV 28.397022 ORP CALIBRATION SOLUTION, 470MV 26.29

YORP15

ORP3

EcoSense® is a registered trademark of YSI, Inc. Pinpoint® is a registered trademark of Dell Technology DBA American Marine, Inc.

Water PollutionAny physical, biological or chemical change in water quality that adversely affects living organisms or makes water unsuitable for desired uses can be considered pollution.Common Impurities in WaterDissolved: Cations, anions, organic compounds such as vegetative dyes and pesticides and gases such as hydrogen sulfide and chlorine.Suspended: Silt, clay, feces, organic and inorganic colloids and living organisms such as bacteria, viruses, protozoa and algae.Floating: Oils and grease, feces and debris.Water Quality CharacteristicsPhysical: Total suspended and dissolved solids, turbidity, color, odors and temperature.Chemical: pH, alkalinity, hardness, conductivity, dissolved gases, etc.Biological: Algae and microbes (bacteria, protozoa, fungi, etc.).Water Quality IndicatorThe amount of oxygen dissolved (D.O.) in water is a good indicator of water quality commonly used in aquaculture. Water with a D.O. of 8 ppm will support game fish and other desirable forms of life. Water with less than 2 ppm oxygen will support only certain fish, worms, bacteria, fungi and other decomposers. Certain organic materials increase oxygen consumption by decomposers. This is measured by the biochemical oxygen demand (BOD). This is the amount of oxygen used by microbes,

mainly bacteria, in the oxidation of organic materials. The standard test is for 5 days at 20°C, and the value it yields is referred to as the 5 day biochemical oxygen demand, commonly shown as BOD5 (see Index for BOD meters). Another measurement is chemical oxygen demand (COD), which is the measurement of the organic materials in terms of the oxygen required to chemically oxidize them. It is measured by boiling and refluxing the sample with a strong oxidizing agent (potassium dichromate), then determining the amount of agent used.Typical Treatment Processes for Organic CompoundsAnaerobic DigestionBiological oxidation of degradable organics by microbes under conditions where there is no molecular oxygen. These are mainly used for swine, poultry and beef industries.Digestion is done by anaerobic bacteria, organic-acid forming and methane-producing heterotrophs.Advantages: Low operational costs, no need for aeration and self-sufficiency if managed properly.Disadvantages: Odors, sludge must be removed periodically, land space needed (long treatment time), and NIMBY (not in my back yard).Aerobic DigestionBiological oxidation of organics under conditions where there is molecular oxygen. Digestion is done by aerobic and facultative bacteria.Advantages: Less odor, reduction in pollution characteristics of the effluent and low treatment time.Disadvantages: Higher operational cost (equipment maintenance, electrical cost).

TECH TALK 67

PINPOINT® ORP METER FW SW

This little meter offers ORP data at a very affordable price. Detachable probe with 10' cable uses BNC connector and is accurate to ±1 mV. Epoxy-covered electrode with a platinum band and silver/silver chloride (Ag/AgCl) tip. For calibration, it has an easy-to-use offset screw. Liquid crystal display. Powered by single 9V battery (included). Can be used in both fresh and salt water. Measures 2" x 5.5". Six-month warranty. Probe included. Calibration solutions sold separately. Meter is not waterproof nor water-resistant.

MODEL EACH

ORP3 ORP/REDOX METER $141.79ORP3R ORP REPLACEMENT PROBE 78.79ORP3CS CALIBRATION FLUID, 350 ML 4.19PA12 OPTIONAL AC ADAPTER 12.79



1SSM100

MODEL EACH

1SSM100 PT4 TRACKER HANDHELD METER $714.991SSP0031 TGP/TEMPERATURE SMART PROBE, 5-M CABLE 739.991SSP060 LUMI4 TGP OPTICAL O2/TEMP PROBE, 5-M CABLE 3,410.001SSA025 REPL. TGP CARTRIDGE FOR 1SSP0031 186.991SSP070 LUMI4 REPL. D.O. PROBE CAP 347.991SSP080 LUMI4 REPL. TGP CARTRIDGE 207.991SSA015 PT4 TRACKER EXTEND. DEPLOYMENT PACKAGE (CASE, BATTERIES, CHARGER) 779.999EPTPS003 GEL CELL BATTERY, 6V, 12AH 42.999EMSC033 NIMH RECHARGEABLE BATTERY PACK, 4 X AA 34.991SSA005 CHARGER CABLE W/AC ADAPTER 93.991SSA006 CHARGER CABLE W/CAR ADAPTER 93.991SSA007 DATA TRANSFER CABLE W/USB ADAPTER, BULGIN CONNECTOR 89.99

TOTAL DISSOLVED GAS PRESSURE (TGP) METERThe Pentair Aquatic Eco-Systems Point Four Tracker provides measurements for TGP (mmHg or % saturation), ∆P, barometric pressure (mmHg) and temperature (ºC).Increasing water temperatures, injection of air in water, algal blooms or pressurized pumping can result in gas supersaturation. This may lead to bubble trauma or sub-lethal toxicological problems for aquatic species. The TGP probe provides a rapid and accurate measurement of total dissolved gas pressure.The Tracker has simple calibration procedures and easy to understand menus. The handheld meter features a tough membrane keypad and graphical display with a user-selectable backlight. The Tracker has two pressure sensors, one measures total dissolved gas pressure (TGP), and one measures barometric pressure (BP). Also has datalogging capabilities. The batteries are rechargeable and an AC adapter is included with each unit.

SYSTEM SPECS

PARAMETER RANGE RANGE RESOLUTION

MEASUREMENTS: Total Gas Pressure (TGP)Barometric Pressure (BP)Temperature

0–1,550 mmHg0–1,550 mmHg

0.0–40.0ºC

1 mmHg1 mmHg

0.1ºC

DERIVED: Total Gas Pressure (TGP)∆P (TGP-BP)

0–200%-1,550–1,550 mmHg

1%1 mmHg

SupersaturationThe measurement of total dissolved gas pressure (TGP) can be required in aquaculture. When the total pressure of all gases in the water exceeds the ambient atmospheric pressure at the water’s surface, supersaturation exists. The effect of excessive supersaturation on fish has been well documented and has caused massive fishkills. TGP as low as 103% can be lethal!Supersaturation can be caused by numerous man-made and natural sources:• Dam spillways can allow a high volume discharge to plunge air deep into the receiving water.• Water pump inlets can suck air, putting that air under high pressure in the piping (this is all

too common, even in aquariums).• Naturally high levels of nitrogen can be found in well water.• Algae blooms can cause supersaturated levels of oxygen.• Temperature changes, which affect the saturation level. Simply heating the water can cause

lethal supersaturation.

TECH TALK 9

Meter & Probe Sold Separately

202 WATER QUALITYTotal Dissolved Gas Pressure (TGP) Meter

IN-HOUSE REPAIR AND SERVICE AVAILABLE Contact Pentair Aquatic Eco-Systems for more details.

1SSP060 - Lumi4 Probe: Optical DO/Temp & TGP



203

SYSTEM SPECS

PARAMETER RANGE RANGE RESOLUTION

MEASUREMENTS: Total Gas Pressure (TGP)Barometric Pressure (BP)Temperature

0–1,550 mmHg0–1,550 mmHg

0.0–40.0ºC

1 mmHg1 mmHg

0.1ºC

DERIVED: Total Gas Pressure (TGP)∆P (TGP-BP)

0–200%-1,550–1,550 mmHg

1%1 mmHg

1SSM002MODEL EACH

1SSM002 TGP TRANSMITTER $960.791SSA025 REPL. TGP CARTRIDGE 186.991SSA029 PC SOFTWARE AND CABLE 78.791PTPS011 115VAC TO 12VDC POWER SUPPLY 48.49

TOTAL DISSOLVED GAS PRESSURE (TGP) TRANSMITTERThe Pentair Point Four Systems TGP Transmitter is a stand-alone probe for the measurement of total dissolved gas pressure. It provides measurement for TGP (mmHg or % saturation), ∆P (TGP-BP), barometric pressure (BP) (mmHg) and temperature (ºC).Two analog outputs are available from each TGP probe. They are available in 0-20 mA, 4-20 mA or 0-5VDC and can be configured to any of the five available measurement parameters. Measurements are also available via RS-485 and can be viewed on a PC with the optional software package. TGP probes are not loop-powered and can accept a 9-33VDC power supply. 115VAC to 12VDC power supply is optional.

MODEL EACH

1OXYCO485 OXYGUARD CO2 PORTABLE $2,722.001OXYCO495 OXYGUARD CO2 PORTABLE W/DATA LOGGER, 230VAC CHARGER 3,455.001OXYCO477 PH CONDITIONER, 75 G 22.191OXYCO478 CALIBRATION SOLUTION, 100 ML 62.991OXYCO476 CALIBRATION BEAKER W/STIRRER 425.291OXYCO480 CALIBRATION ACCESSORIES PACK 385.391OXYCO496 OXYGUARD DISSOLVED CO2 PROBE 817.99

OXYGUARD® PORTABLE CO2 METERThe OxyGuard portable CO2 meter is a reliable and easy-to-use instrument that measures dissolved carbon dioxide in water. The meter consists of a probe and a battery-powered transmitter. The meter displays CO2 concentration and an analog signal as output. The transmitter has an on/off switch, "slope" and "zero" adjustments. Battery charger (230V), calibration accessories and 3-m cable are included. A version with built-in data logger is available.Measures the CO2 gas pressure directly and is not affected by carbonates or other dissolved substances. It is therefore possible to achieve simple, continuous direct measurements of carbon dioxide in water that affects fish.Methods such as test kits, laboratory analysis and the detection of pH changes are subject to disturbance from the dissolved substances found in aquaculture water. The OxyGuard CO2 measures only the CO2 that affects the fish, which is the free dissolved CO2 gas. It is reliable and accurate. Calibration accessories pack includes beaker with stirrer and magnet; 75 g of pH conditioner with dosing spoon; 100 mL of calibration solution with dosing syringe; and adjustment screwdriver.


IN-HOUSE REPAIR AND SERVICE AVAILABLE Contact Pentair Aquatic Eco-Systems for more details.

203WATER QUALITYTGP and CO2 Meters



Pinpoint® is a registered trademark of Dell Technology DBA American Marine, Inc. YSI®

and EcoSense® are registered trademarks of YSI, INc.

PH370

SYSTEM SPECS

PH Range: -2–16Resolution: 0.01Accuracy: ± 0.1%

ORP Range: -1,999–1,999 mVResolution: 1 mVAccuracy: ± 0.1%

TEMPERATURE Range: -10–120°CResolution: 0.1°CAccuracy: ± 0.3°C

Y1000A


PINPOINT® PH METER FW SW

The Pinpoint® PH370 meter is a great little pH meter at a very affordable price. The detachable probe with its 10' cable uses a BNC connector. It has built-in slope and calibration adjustments but is not temperature compensated (if you take measurements anywhere near room temperature, the temperature error will be negligible). Two-point calibration. The digital display is easy to read, even in full sun. Two-year warranty on the meter only. Measures 5.5" L x 3" W, weighs just 0.3 lb. • Includes pH probe, 10’ cable, calibration solutions #7 & #10, and 9V battery• Not waterproof nor water-resistant

MODEL EACH

PH370 PH METER $103.99PH370R PH REPLACEMENT PROBE 48.89PA12 OPTIONAL AC ADAPTER 12.79


MODEL EACH

Y1000A PH100A METER ONLY $264.99Y1001 PH/TEMP PROBE W/3' CABLE 98.99Y1004 PH/TEMP PROBE W/12' CABLE 146.99Y1101 PH ELECTRODE W/3' CABLE 59.99Y1201 TEMP PROBE W/3' CABLE 54.99Y1251 ORP ELECTRODE W/3' CABLE 94.99Y1111 PIERCING PROBE DOUBLE JUNCTION 146.99Y1122 FLAT GLASS PROBE DOUBLE JUNCTION 146.99

ECOSENSE® PH100A PH/TEMP METER FW SW

The EcoSense pH100A measures pH and temperature (ORP requires separate probe) quickly and accurately. The electrode offset recognition function displays electrode efficiency and indicates when it is time to replace the pH electrode. Features include internal buffer recognition, auto/manual temperature compensation and a large LCD display that simultaneously displays pH or mV and temperature (ºC only). Electrodes with 3' (1 m) cables are available in pH or combination pH/mV. Two-point pH calibration. Cables are waterproof over their whole length. 9V batteries included. Measures 7" x 3". Order meter and probe separately. One-year warranty on meter, six months on probes. Calibration solutions sold separately.

204 WATER QUALITYpH Meters



205

WD-35634-30

pHTestr® is a registered trademark of Cole-Parmer Instruments Co.

PH/TEMP TESTERS FW SW

These floating testers have a large LCD, push-button calibration with buffer recognition (can be calibrated to 3 points), auto shut-off after 8.5 minutes, automatic temperature compensation and a user-replaceable double-junction sensor. These testers will float if dropped in water. The pHTestr® meter 10 reads -1.0 to 15.0, the pHTestr® 20 and 30 read -1.00 to 15.00 and the pHTestr® 30 has simultaneous temperature display in ºC or ºF. All have self-diagnostic messages such as battery power indicator and a hold function to freeze values for future use. Measures 1.5" W x 6.5" long, weighs 0.3 lb. One-year instrument warranty, six-month electrode warranty. Calibration solutions sold separately.

MODEL EACH

WD-35634-10 PHTESTR 10 $100.79WD-35634-20 PHTESTR 20 110.29WD-35634-30 PHTESTR 30 121.7935624-38 REPL. PH SENSOR 80.99TRB REPL. BATTERIES (6-PK) 20.69

pH Probe Care & StorageProper handling and storage of pH electrodes will not only help to prolong the electrode’s life, but also will ensure fast, accurate readings. General guidelines include:• Electrodes should be rinsed between samples with deionized or distilled water.• Never wipe an electrode dry as this can cause erroneous readings due to static charges.

• Never store electrodes in water; doing so will cause a sluggish response.• Always keep the tip of the pH electrode moist. Electrode storage solution is a solution of 4M

KCl. If unavailable, a pH 4 buffer solution will also work temporarily.• In general, pH buffers only have a two-year shelf life unopened. Once opened, the shelf life

drops to 2–3 months. However, open pH 10 calibration solution only has a 30-day shelf life.

TECH TALK 30

YPH10A

ECOSENSE® PH10A PH/TEMP PEN FW SW

The EcoSense pH10A pH/Temperature pen features one-hand operation, 50-set memory and low cost. Measures 0 to 14 with an accuracy of ± 0.02. The pen has IP67 waterproof grey housing; ATC; auto-buffer recognition with 1-, 2- or 3-point calibration; and a replaceable electrode. Real time clock provides data date and time stamp. "Hold" feature locks reading on display, which has on-screen instructions. Has a belt clip and lanyard on the back and floats if dropped in water. Measures 2" W x 7.5" L, weighs 0.3 lb. One-year instrument warranty, six-month electrode warranty. Calibration solutions sold separately.

MODEL EACH

YPH10A PH10A PEN $115.99606110 REPL. ELECTRODE FOR YPH10A PEN (GREY) 52.99605113 REPL. ELECTRODE FOR YPH10 PEN(BLUE) 52.99605118 LR44 REPL. BATTERIES (4) 4.99Y580 CARRYING CASE 28.99

WATER QUALITYpH Meters

205



206 WATER QUALITYConductivity Meters

MODEL EACH

KITSYEC300A-1 METER, PROBE, 1M CABLE, CARRYING CASE $564.99 YEC300A-4 METER, PROBE, 4M CABLE, CARRYING CASE 584.99 YEC300A-10 METER, PROBE, 10M CABLE, CARRYING CASE 599.99

METER ONLYYEC300A EC300A METER $299.99

CABLES WITH PROBEY606044 1 METER CABLE WITH PROBE $249.99 Y605395 4 METER CABLE WITH PROBE 264.99

CALIBRATION SOLUTIONSY3167-E 1,000 uS/CM PER PINT (FRESH WATER) $19.99 Y3168-E 10,000 uS/CM PER PINT (BRACKISH WATER) 20.99 Y3169-E 1,000 uS/CM PER PINT (FRESH WATER) 20.99

ACCESSORIES Y606043 HARD SIDED CARRYING CASE $39.99


ECOSENSE® EC300A CONDUCTIVITY/SALINITY/TDS/TEMP METERThe EcoSense EC300A offers convenient conductivity, specific conductance, salinity, total dissolved solids and temperature for true field applications. Meter has IP67 waterproof rating and automatic temperature compensation. Automatic shutoff after 30 minutes of inactivity helps preserve 9V battery life, which can last up to 500 hours. 50 data-set memory.

YEC300A-4

CM6

2-YEAR WARRANTY

PINPOINT® CONDUCTIVITY METERIf you need to measure freshwater conductivity in µS, this economical, two-range meter is an excellent choice. This scale is typically used for fresh water and low concentrations of salt. The LED reads in two ranges at the flip of a switch. Measures from 0–2,000 µS or 0–20,000 µS. Accurate to ±4% of reading. 5.5" L x 3" W, weighs only 0.4 lb.

• Includes 3’ cable and 9v battery• Not waterproof nor water-resistant• Calibration solution sold separately

MODEL EACH

CM6 CONDUCTIVITY METER $131.29PA12 OPTIONAL AC ADAPTER 12.79

SYSTEM SPECS

RANGE RESOLUTION ACCURACY

CONDUCTIVITY 0 to 499.9 µS/cm0 to 4999 µS/cm0 to 49.99 mS/cm0 to 200.0 mS/cm

0.1 µS/cm1 µS/cm

0.01 mS/cm0.1 mS/cm

± (1% of reading + 2 µS/cm)± (1% of reading + 5 µS/cm)

± (1% of reading + 0.05 mS/cm)± (2.5% of reading + 0.5 mS/cm)

SALINITY 0.0 to 70.0 ppt, calculated ±0.2% FS 0.1 ppt

TEMPERATURE -10 to +90°C (14 to 194°F) 0.1°C ±0.2°C or ±0.4%, whichever is greater

TDS TDS in g/L calculated; enter constant values from

0.30 to 1.00, default value 0.65

EcoSense® is a registered trademark of YSI, Inc.



207

ExStik® is a registered trademark of Extech Instruments Corp.

SYSTEM SPECS


CONDUCTIVITY 0 μS to 19.90 mS, with manual or auto ranging

0 to 1990 μS/cm5 μS/cm

2.00 to 19.90 mS/cm0.05 mS/cm

±1% FS

TEMPERATURE 0 to 99.5°C (32.0 to 212 °F)

0.5 °C (1 °F) ±0.5°C (1°F)

SYSTEM SPECS


CONDUCTIVITY 0–199.9 µS/cm200–1,999 µS/cm2–19.99 mS/cm

.1 µS/cm ±2% FS

TDS/SALINITY 0–99.9 ppm (mg/L)100–999 ppm (mg/L)

1–9.99 ppt (g/L)

.1 ppm (mg/L) ±2% FS

PH 0 to 14.00 .01 ± .01

EC500

ECOSENSE® EC30A CONDUCTIVITY/TDS/TEMP PENThe EcoSense® EC30A pen-style instrument provides an ultimate feature set over similar competitive models. Features an easy-to-use interface, simple one-hand operation and low cost of ownership over the life of the product. The easy, user-replaceable electrode ensures the instrument is always ready for use. Meter has IP67 waterproof rating and automatic temperature compensation. 50 data-set memory and 200-hour battery life.Measures conductivity, TDS and temperature with the following features: • 1- or 2-point calibration• Clear, easy-to-read display with on-screen instructions• Selectable units of measure for conductivity, TDS and temp• Selectable or auto-ranging for conductivity or TDS

MODEL EACH

YEC30A COND/TDS/TEMP PEN $146.99Y3167-E CALIBRATION SOLUTION, 1,000 uS/CM (FRESH WATER) 19.99Y3168-E CALIBRATION SOLUTION, 10,000 uS/CM (BRACKISH WATER) 20.99Y3169-E CALIBRATION SOLUTION, 50,000 uS/CM (SALT WATER) 20.99

MODEL EACH

EC500 EXSTIK II® WATERPROOF METER $167.99EC505 SPARE ELECTRODE 68.19EX006 WEIGHTED BASE W/5 SOLUTION CUPS 16.79CA895 SMALL VINYL CARRYING CASE 12.89

EXSTIK® II PH/CONDUCTIVITY/TDS/SALINITY PENThe Extech® EXSTIK® II waterproof meter has a rugged combination, flat-surface pH electrode (with auto-ranging), high-accuracy conductivity cell. RENEW feature alerts users when the electrode needs replacing. Adjustable conductivity to TDS ratio from .4 to 1.0 and .5 fixed salinity ratio. Meter also has ATC, auto shut-off and low battery indication. The internal memory stores up to 25 labeled readings for recall. Measures 1.5" W x 7" L. Due to its salinity range, this meter is not compatible with salt water. One-year warranty on meter, six months on sensor.

“The ExStik II DO and Conductivity meters work perfectly for collecting data quickly and accurately in the field, and save a tremendous amount of space aboard the small boat. They worked so well we bought a second set!”G. JonesLake Operations Manager

WATER QUALITYConductivity Meters

207



Scale view.

VITAL SINE® SALINITY REFRACTOMETER TECH FAV

The VITAL SINE salinity refractometer features a magnified scale for better visual accuracy. Other features include solid aluminum construction, a rubber-gripped body and temperature compensation between 10 and 30°C (50–86°F). To calibrate, simply loosen the handset screw, place a few drops of salt-free water on the prism, turn the calibration ring until the shadowline is at zero and secure the set screw—that's it! It reads specific gravity (1.000 to 1.070) and salinity in parts per thousand (0–100 in 1 ppt divisions). Refractometer includes a black vinyl zip case, transfer pipette and cleaning cloth. Measures 11/2" D x 7" L (4 x 18 cm), weighs 0.6 lb (285 g). One-year warranty.

• Largest and sharpest scale display available.• Calibration ring for simplified calibration.

MODEL EACH

SR6 SALINITY REFRACTOMETER $142.29

Rubber Hood. Houses the focusable lens and prevents light from entering

through the eyepiece during use.

Daylight Plate. Exceptionally durable with a double-hinge design allowing

even thick samples to be easily measured.

Calibration Ring. For rapid calibrations.

Antiroll Stand. Protects against rolling off

a table.

Rubber Grip.

Scale view.

Do not dip a refractometer in water, as this will void the warranty.Use a dropper and place a few drops on the prism. The refractometer will provide many years of service if used this way.Dry after use otherwise will cause damage to the device.

SALINITY REFRACTOMETERHere's an economical, automatic temperature-compensated salinity refractometer, featuring an automatic temperature correction from 50–86ºF (10–30ºC) and a dual scale reading 0–100 ppt and 1.000–1.070 specific gravity. Each refractometer is tested to ensure an accurate instrument. Six-month warranty. Weighs 0.6 lb.

MODEL EACH

SR5-AQ SALINITY REFRACTOMETER $47.19

Dry after use otherwise will cause damage to the device.

208 WATER QUALITYSalinity Refractometers



209WATER QUALITYSalinity Meters

209

Measuring SalinityWhen culturing saltwater organisms, less than a 10 percent variation in salinity (± 5% or ± 2 ppt) is often required. The measuring methods cover a wide range of cost, convenience and accuracy. Basically, salinity is the sum of all dissolved ions in the water (not just sodium and chloride), expressed as parts per thousand (grams per kilogram). One measurement method is to titrate chlorinity (chloride) and calculate the salinity based on the assumption that the composition is the same as seawater. Usually titrations are based on volumes, which can introduce a 2.5 percent error if not done correctly. It is much more time consuming than other methods and used as a means of checking other techniques. Density is the basis of the hydrometer measuring method. Salinity can then be determined from tables based on density (specific gravity) and temperature. Refractometers are also density-based. They provide fast, accurate (± 1 ppt) salinity measurements. Generally, temperature-compensated models are suggested. Cost and care are the

biggest drawbacks. Calibration using certified seawater is best; however, fresh water is a reasonable alternative for general aquaculture uses. Electrical conductivity is another method of determining salinity. Conductivity measurements are best at 25°C and any difference from this requires compensation. If there is a question about temperature compensation, simply take a reading, change the temperature of the water by 5 or 10 degrees and measure again. It should give the same salinity. Some units give readings in millisiemens (mS) and require a salinity conversion table. Others read directly in salinity (called a salinity meter). Regular calibration with a standard solution is recommended. The information in this Tech Talk was provided by Thomas Frakes, Technical Consultant, Aquarium Systems, Inc.

TECH TALK 28

2-YEAR WARRANTY


SPECIFICATIONS

Range (Salinity) 0 to 10 ppt

Resolution (Temperature) 0.1

Resolution (Conductivity) 0.1 ppt, 0.01%

Resolution (Salinity) 0.1 ppt, 0.01%

Accuracy (Temperature) ±0.5° C

Accuracy (Salinity) ±1.0% full-scale

Temperature compensation Automatic

Display LCD

Calibration 1 point

Waterproof Yes

Power Four 1.5 V batteries (included)

Battery life > 200 hours

CE Compliance Yes

SALINITY METER FW SW

This Pinpoint® salinity meter measures conductivity, giving a digital readout in mS (millisiemens). The table included will give the corresponding reading in both specific gravity and salinity to 62 ppt. This meter is temperature compensated for accuracy of ±4%. Uses one 9V battery (included). Weighs only 0.6 lb and measures 5.5" L x 3" W.

• Includes probe, 3’ cable, calibrating solution and 9V battery• Not waterproof, nor water-resistant

MODEL EACH

SM6 SALINITY METER $141.79PA12 OPTIONAL AC ADAPTER 12.79

POCKET SALINITY TESTERGreat for measuring salt levels in koi pondsThis low-range tester is specifically designed for measuring those difficult low-salt concentrations in koi ponds. IP67 waterproof. Easy calibration trimmer is isolated inside the battery compartment to prevent accidental tampering. Long-life sensor element is not replaceable. Includes protective case. 61/4" L x 15/8" W x 11/8" D, weighs 0.4 lb. Six-month warranty. Calibration solutions sold separately.

MODEL EACH

SWT2-2 ECOTESTR SALT TESTER $72.49

KOI


PRO30 INSTRUMENT SPECIFICATIONS

CONDUCTIVITY ±0.5% OF READING OR 1.0 uS/cm, WHICHEVER GREATERSIZE 8.3 cm WIDTH X 21.6 cm LENGTH X 5.7 cm DEPTH (3.25 IN. X 8.5 IN. X 2.25 IN.) WEIGHT WITH BATTERIES 475 GRAMS (1.05 LBS.)POWER 2 ALKALINE C-CELLS PROVIDING 400 HOURS OF BATTERY LIFE; LOW BATTERY INDICATOR ON PRO30 CABLES 1- 4- 10- 20- AND 30-m LENGTHS (3.28, 13.1, 32.8, 65.6 FT.)WARRANTY 3-YEAR INSTRUMENT; 2-YEAR CABLE AND SENSOR TDS CONSTANT RANGE ADJUSTABLE; 0.3-1.0 CONDUCTIVITY REFERENCE TEMP ADJUSTABLE; RANGE 15°C TO 25°C SPECIFIC CONDUCTANCE TEMP COMP ADJUSTABLE; 0 TO 4%DATA MEMORY 50 DATA SETS LANGUAGES ENGLISH, SPANISH, GERMAN, FRENCHCERTIFICATIONS ROHS, CE, WEEE, IP-67, 1-METER DROP TEST



YSI® PRO30 CONDUCTIVITY/TDS/SALINITY/TEMP METERThe YSI Pro30 is ideal in any field application for the measurement of conductivity, salinity, TDS (total dissolved solids), and temperature. The Pro30 features user-replaceable cables in lengths up to 30-meters, 50 data set memory, and a simple calibration routine. True field performance is verified with the IP-67 waterproof and impact resistant case - drop tested at 1-meter. Additionally, the YSI super- stable 4-electrode conductivity cell is so reliable it is built directly into the cable.

• 3-year meter, 2-year cable and sensor warranty• User-replaceable cables. Conductivity sensor built into cable. Choose among

1-, 4-, 10-, 20-, or 30-meter cables• Fast cal routine allows easy calibrations with the press of a button.

Remembers the previous calibration values and simply walks you through the routine

• Stores 50 data sets; no need to write down data• Graphic, backlit display and glow in the dark keypad• Tough. IP-67, impact-resistant, waterproof case even without the battery

cover. Rubber over molded case provides extra durability• Rugged, military spec connectors. Bayonet style with keyed

quarter-turn lock• Super-stable, weighted 4-electrode conductivity sensor is built in for true

field performance and designed for rugged conditions. Easily cleaned with a conductivity cleaning brush

• The YSI Pro30 is a great replacement for the YSI 30

MODEL EACH

Y60530 PRO30 METER ONLY $569.99Y60530-4 PRO30 4M CABLE WITH PROBE 329.99Y60530-10 PRO30 10M CABLE WITH PROBE 389.99Y60530-20 PRO30 20M CABLE WITH PROBE 434.99Y60530-30 PRO30 30M CABLE WITH PROBE 544.99Y3167-E CALIBRATION SOLUTION, 1,000 uS/CM PER PINT (FRESH WATER) 19.99Y3168-E CALIBRATION SOLUTION, 10,000 uS/CM PER PINT (BRACHISH WATER) 20.99Y3169-E CALIBRATION SOLUTION, 50,000 uS/CM PER PINT (SALT WATER) 20.99

210 WATER QUALITYConductivity/TDS/Salinity/Temp Meter




WATER QUALITYpH/ORP/DO/Temperature Meter

211

MODEL EACH

METERY605120 PRO1020 METER ONLY $749.99

PROBESY6202 GALVANIC D.O. (INCLUDES MEMBRANE KIT) $179.99Y6203 POLAROGRAPHIC D.O. (INCLUDES MEMBRANE KIT) 179.99Y6101 PH ISE 174.99Y6102 ORP ISE 204.99Y6103 PH/ORP COMBO ISE (NOT FOR USE ON DUAL ISE CABLES) 294.99

CABLESY605120-4 4 METER CABLE KIT $579.99Y605120-10 10 METER CABLE KIT 629.99Y605120-20 20 METER CABLE KIT 719.99Y605120-30 30 METER CABLE KIT 854.99

MEMBRANE CAPSY5908 POLAROGRAPHIC $59.99Y5913 GALVANIC 59.99

Meter, Cable & Probe Sold Separately


YSI® PRO1020 PH/ORP/DO/TEMPERATURE METERRugged and reliable, the YSI® Pro1020 provides everything you need in a handheld instrument for the measurement of either pH or ORP, along with temperature and dissolved oxygen. The internal barometer, Quick Cal feature, and simple interface make getting accurate data extremely simple.• IP67 waterproof rating• 3-year instrument warranty; 2-year cable• Quick Cal allows calibrations within minutes• 50 data-set memory ensures data integrity• Graphic, backlit display and glow-in-the-dark keypad• Languages - English, Spanish, French, Portuguese• Choose either Galvanic or Polarographic DO probes• Quickest response times, PE cap membranes• Auto-buffer recognition• YSI PRO1020 replaced YSI 85

PRO1020 INSTRUMENT SPECIFICATIONS

TEMPERATURE RANGE -5 TO 55°C (0 TO 45°C FOR DO COMPENSATION RANGE FOR MG/L ) RESOLUTION 0.1°C ACCURACY 0.2°C PH RANGE 0 TO 14 PH UNITS RESOLUTION 0.01 ACCURACY ±0.2 ORP RANGE -1500 TO 1500 MV RESOLUTION 1 MV ACCURACY ±20 MVDISSOLVED OXYGEN RANGE 0 TO 500% AIR SATURATION (% SATURATION) RESOLUTION 0.1% OR 1% AIR SATURATION (USER SELECTABLE) ACCURACY 0 TO 200% AIR SATURATION, ±2% OF THE READING OR ±2% AIR SATURATION, WHICHEVER IS GREATER; 200 TO 500% AIR SATURATION, ±6% OF THE READING DISSOLVED OXYGEN RANGE 0 TO 50 MG/L(MG/L) RESOLUTION RESOLUTION 0.01 OR 0.1 MG/L (USER SELECTABLE) ACCURACY 0 TO 20 MG/L, ±2% OF THE READING OR ±0.2 MG/L, WHICHEVER IS GREATER; 20 TO 50 MG/L, ±6% OF THE READINGBAROMETER RANGE 500 TO 800 MMHG (MMHG, INHG, MBARS, PSI, KPA) RESOLUTION 0.1 MMHG ACCURACY ±5 MM HG WITHIN ±15°C OF CALIBRATION TEMPERATURE

CALIBRATION SOLUTIONSCAL4 PH 4.01 $13.99CAL7 PH 7.00 13.99CAL10 PH 10.00 13.99Y3167-E 1,000 uS/CM PER PINT (FRESH WATER) 19.99Y3168-E 10,000 uS/CM PER PINT (BRACKISH WATER) 20.99Y3169-E 50,000 uS/CM PER PINT (SALT WATER) 20.99Y3628 ZOBELL ORP TEST 32.99


212 WATER QUALITYDO/Cond/Salinity/TDS/Temp Meter

Y6052030


SYSTEM SPECS (INSTRUMENT, PROBE & CABLE)

D.O. (%) Sensor Type: Polarographic or GalvanicRange: 0 to 500% air saturationAccuracy: 0 to 200% air saturation, ± 2% of the reading or ±2% air saturation, whichever is greater; 200 to 500% air saturation, ± 6% of the readingResolution: 0.1% or 1% air saturation (user selectable)

D.O. (MG/L) Sensor Type: Polarographic or GalvanicRange: 0 to 50 mg/LAccuracy: 0 to 20 mg/L, ± 2% of the reading or ±0.2 mg/L, whichever is greater; 20 to 50 mg/L, ± 6% of the readingResolution: 0.01 or 0.1 mg/L (user selectable)

CONDUCTIVITY (MS, US)

Sensor Type: Four-electrode cellRange: 0 to 200 mS/cm (auto range)Accuracy: 1- or 4-m cable, ±1.0% of the reading or 1.0 uS/cm, whichever is greater 10- 20- or 30-m cable, ±2.0% of the reading or 1.0 uS/cm, whichever is greaterResolution: 0.0001 to 0.1 mS/cm (range dependent)

SALINITY (PPT, PSU)

Sensor Type: CalculatedRange: 0 to 70 pptAccuracy: ±1% of the reading or 0.1 ppt, whichever is greaterResolution: 0.01 ppt

TOTAL DISSOLVED SOLIDS (TDS) (MG/L, G/L)

Sensor Type: CalculatedRange: 0 to 100 g/L TDS constant range 0.30 to 1.00 (0.65 default)Accuracy: Dependent on temp and conductivity; calculated from those parametersResolution: 0.001, 0.01, 0.1 g/L

TEMPERATURE Range: -5 to 55°C (0 to 45°C; DO compensation range for mg/L) Accuracy: ±0.2°CResolution: 0.1°C

BAROMETER Range: 500 to 800 mmHgAccuracy: ±5 mm Hg within ± 15°C temperature range from calibration pointResolution: 0.1 mmHg



YSI® PRO2030 DISSOLVED OXYGEN/CONDUCTIVITY/SALINITY/TDS/TEMP METERThe YSI Pro2030 provides everything you need in a handheld dissolved oxygen instrument with conductivity. Automatically compensates D.O. readings for changes in salinity. User-replaceable D.O. sensors and cables, 50 data set memory and simple D.O. calibration make the Pro2030 user-friendly. Rugged design and 1-meter drop tests ensure the instrument remains in your hands to provide years of sampling even in the harshest field conditions. Fast response times allow you to complete your sampling routine quickly, saving time and money. Your perfect handheld for brackish water and/or applications with varying salinity. Instrument has three-year warranty; two years for cable.

• Choose either polarographic or galvanic D.O./Conductivity sensor built into cable• Easy calibration within seconds with the press of a button. Automatic

internal barometric pressure compensation• IP67, impact-resistant, waterproof case even without the battery cover.

Rubber case provides extra durability. Military spec connectors• Quick response times; 95% D.O. response time in approximately

8 seconds with standard membrane• Graphic, back-lit display & glow in the dark keypad• Languages-English, Spanish, French & Portuguese• Automatic salinity compensation for dissolved oxygen

MODEL EACH

METERY6052030 PRO2030 METER $754.99

CABLESY6234C 4M, D.O./CONDUCTIVITY/TEMPERATURE $619.99 Y62310C 10M, D.O./CONDUCTIVITY/TEMPERATURE 679.99 Y62320C 20M, D.O./CONDUCTIVITY/TEMPERATURE 734.99 Y62330C 30M, D.O./CONDUCTIVITY/TEMPERATURE 834.99

PROBESY6202 GALVANIC D.O. $179.99 Y6203 POLAROGRAPHIC D.O. 179.99


WATER QUALITYTech Talk

213

TECH TALK 47

Water Quality GuideThese are healthy, growing tolerances, not limits for fatalities. Use this chart for guidelines only. Tolerance levels can vary greatly depending on a variety of factors. Some species are also sensitive to nitrite above 40 ppm. Fish will excrete about 14 grams of ammonia for each pound of food eaten (@ 35% protein). Test kits read total ammonia; this guide gives un-ionized ammonia levels, which is the toxic form. See chart for conversion.

Marine Reef Water Quality GuideUse these numbers for guidelines only, not for water quality limits. These are healthy growing tolerances. Tolerance levels can vary greatly depending upon a variety of factors.Temperature: 72–78°F Nitrate: <1.0 ppmRedox: 350–400mV Phosphate: <0.1 ppmSalinity: 22–35 ppt Strontium: 8–10 pppH: 8.2 Alkalinity: 125–160 mg/L**Redox Calcium: 350*–500 ppm Iodine*: 0.06 ppmDissolved Oxygen: 5–7 ppm Silicate*: <2.0 ppmBoron*: 4.5–4.8 ppm Ammonia: 0 ppmRecommended light levels: 4–6 watts/gallon in a 1:1 ratio of actinic blue to daylight. *Level found in natural seawater. **Calcium carbonate (CaCO3).

UN-IONIZED D.O. PH ALKALINITY CO2 AMMONIA NITRITE HARDNESS CHLORIDE SALINITY TEMP MG/L UNITS MG/L MG/L MG/L MG/L MG/L MG/L PPT

Trout 45–68°F/7–20°C 5–12 5.5–8 50–250 0–20 0–0.02 0–0.2 50–350 0–1,500 0–3Hybrid Striped Bass 70–85°F/21–29°C 4–10 6–8 50–250 0–25 0–0.03 0–0.8 50–350 0–1,500 0–3Tilapia 75–90°F/24–32°C 3–10 6–8 50–250 0–30 0–0.04 0–0.8 50–350 0–5,000 0–15Goldfish/Koi 65–75°F/18–24°C 4–10 6–8 50–250 0–25 0–0.08 0–0.6 50–350 0–2,000 0–4Shrimp (Freshwater) 68–80°F/20–27°C 4–10 6.5–9 60–100 0–20 0–0.05 0–0.9 60–250 0–1,500 0–3Shrimp (Saltwater) 60–75°F/16–24°C 4–10 6–8.5 50–250 0–15 0–0.01 0–0.1 50–350 13,000–18,000 2–35Minnows Shiners 60–75°F/16–24°C 4–10 6–8 50–250 0–25 0–0.03 0–0.6 50–350 0–2,500 0–5Tropical Fish (Freshwater) 72–84°F/22–29°C 4–10 6–8 50–250 0–20 0–0.03 0–0.9 50–350 0–2,500 0–5

Percentage of Un-Ionized Ammonia at Different pH Values and Temperature PH 16ºC/61ºF 20ºC/68ºF 24ºC/75ºF 28ºC/82ºF 32ºC/90ºF

7.0 1% 1% 1% 1% 1% 7.4 1% 1% 1% 2% 2% 7.8 2% 2% 3% 4% 6% 8.2 5% 6% 8% 10% 13% 8.6 11% 14% 17% 22% 28% 9.0 23% 28% 34% 41% 49%Equation: ppm un-ionized ammonia = ppm total ammonia (measured) x un-ionized ammonia (from above). These figures are percentages, so move the decimal point two spaces to the left.

Freshwater Plant Water Quality GuideUse these numbers for guidelines only, not for water quality limits. These are healthy growing tolerances. Tolerance levels can vary greatly depending upon a variety of factors.Temperature: 74–79°F Iron: 0 to 1.0 mg/LpH: 6.8 Phosphate: 0 to 5.0 mg/LDissolved Oxygen: 5–7 ppm Trace Elements: 0 to .5 mg/LNitrate: <40 mg/L Carbonate Hardness (KH): 3.5 to 5.0 dKHCarbon Dioxide:

If dKH level is: Then CO2 level should be:5º 10–15 mg/L10º 15–30 mg/L15º 30–40 mg/L


214 WATER QUALITYMultiparameter

Y60500


Meter, Cable and Probe Sold Separately

YSI® PRO PLUS MULTIPARAMETER METERMeasure up to 11 different parameters with one meter and only a simple cable change! Meter has a backlit display and keypad, graphic display with detailed messages and instructions plus a gauge that continuously shows the battery level. The rubber over-molded case has an IP67 waterproof rating and is drop rated to 1 meter. Instrument can log data (5,000 data-set memory with site identity and GLP event logging) and download it to a PC. Data Manager desktop software, a communication dock and USB cable are included. Meter measures 3.3" x 8.5" x 2.3", weighs 1 lb. Uses 2 C batteries (included). Three year warranty on meters, two years on cables and one year on probes (six-month warranty on ammonium, chloride and nitrate ISEs).• Measure combinations of D.O., temperature, pH, conductivity, salinity, TDS,

ORP, ammonium, nitrate, chloride and barometric pressure• Automatic temperature, salinity and barometric pressure compensation

PRO PLUS KITSChoose the kit that best meets your needs. Kits include Pro Plus instrument, 4 meter cable, choice of pH or pH/ORP probe, and carrying case.

QUATRO CABLE KITThe Quatro cable holds four user-replaceable Professional Series sensors for temperature/conductivity, D.O. and your choice of any two ISEs (pH, ORP, ammonium, nitrate, or chloride). Ammonia (NH3) can be measured if ammonium (NH4) and pH sensor is installed. Kit does not include D.O. and ISE probes.

PRO PLUS KITS MODEL EACH

Y603190 METER, 4M CABLE, Ph PROBE & CARRYING CASE $3,060.00 Y603223 METER, 4M CABLE, PH/ORP PROBE & CARRYING CASE 3,260.00

PRO PLUS METER ONLY MODEL EACH

Y60500 PRO PLUS MULTIPARAMETER METER $1,220.00

CABLES MODEL EACH

Y614C 4 METER FOR ISE/TEMP $259.99Y624C 4 METER FOR DO/TEMP 264.99Y634C 4 METER FOR COND/TEMP 329.99Y6114C 4 METER FOR ISE/ISE/TEMP 579.99Y6124C 4 METER FOR ISE/DO/TEMP 579.99Y6134C 4 METER FOR ISE/COND/TEMP 479.99Y6234C 4 METER FOR DO/COND/TEMP 619.99Y57904 QUATRO CABLE KIT 1,325.00

PROBES MODEL EACH

Y6202 GALVANIC DO (INCLUDES MEMBRANE KIT) $179.99Y6203 POLAROGRAPHIC DO (INCLUDES MEMBRANE KIT) 179.99Y6101 PH ISE 174.99Y6102 ORP ISE 204.99Y6103 PH/ORP COMBO ISE (NOT FOR USE ON DUAL ISE CABLES) 294.99

PROBES (Continued) MODEL EACHY6104 AMMONIUM ISE (FRESH WATER ONLY) $359.99Y6105 CHLORIDE ISE (FRESH WATER ONLY) 359.99Y6106 NITRATE ISE (FRESH WATER ONLY) 359.99

SOLUTIONS MODEL EACH

CAL4 PH 4.01 $13.99CAL7 PH 7.00 13.99CAL10 PH 10.00 13.99Y3167-E 1,000 uS/CM PER PINT (FRESH WATER) 19.99Y3168-E 10,000 uS/CM PER PINT (BRACKISH WATER) 20.99Y3169-E 50,000 uS/CM PER PINT (SALT WATER) 20.99Y3628 ZOBELL ORP TEST 32.99Y3841 AMMONIUM STANDARD 1MG/L (500ML) 81.99Y3842 AMMONIUM STANDARD 10MG/L (500ML) 81.99Y3843 AMMONIUM STANDARD 100MG/L (500ML) 81.99Y3885 NITRATE STANDARD 1MG/L (500ML) 81.99Y3886 NITRATE STANDARD 10MG/L (500ML) 81.99Y3887 NITRATE STANDARD 100MG/L (500ML) 81.99

CARRYING CASE MODEL EACH

Y603075 SOFT SIDED CARRYING CASE $124.99



215SECTIONProducts / Products / Products

215WATER QUALITYMultiparameter

215


DISSOLVED OXYGEN (% SATURATION)

Range: 0–500% air saturationAccuracy: ±2% of the reading or ±2% air saturationResolution: 1% or 0.1% air saturation

DISSOLVED OXYGEN (MG/L) Range: 0–50 mg/L Accuracy: ±2% of the reading or ± 0.2 mg/LResolution: 0.1 or 0.01 mg/L

TEMPERATURE Range: -5–100ºC (D.O. compensation range -5–45ºC)Accuracy: ± 0.2ºC (-5–70ºC), ± 0.3ºC (70 to 100ºC)Resolution: 0.1°C

CONDUCTIVITY Range: 0–200 mS/cmAccuracy: ± 0.5% of reading or ± 0.001 mS/cm (4-meter cable); ±1% of reading or ± 0.001 mS/cm (20-meter cable)Resolution: 0.001–0.1 mS/cm (Range-dependent)

SALINITY Range: 0–70 pptAccuracy: ±1% of reading or ± 0.1 pptResolution: 0.01 ppt

PH Range: 0–14 unitsAccuracy: ± 0.2 unitsResolution: 0.01 units

ISE Range: -1,999–1,999 mVAccuracy: ±20 mVResolution: 0.1 mV

TOTAL DISSOLVED SOLIDS Total Dissolved SolidsCalculated from conductivity (variable constant, default .65)Range: 0–100 g/LResolution: 4 digits

BAROMETER Range: 375–825 mmHgAccuracy: ±3 mmHg (within ±15°C of calibration temp)Resolution: 0.1 mmHgUnits: mmHg, inHg, kPa

AMMONIUM

(ammonia with pH sensor)

Range: 0 to 200 mg/L-N, 0 to 30°CAccuracy: ±10% of reading or 2 mg/L-N,whichever is greater Resolution: 0.01 mg/L

NITRATE Range: 0 to 200 mg/L-N, 0 to 30°CAccuracy: ±10% of reading or 2 mg/L-N,whichever is greater Resolution: 0.01 mg/L

CHLORIDE Range: 0 to 1000 mg/L,0 to 40 °CAccuracy: ±15% of reading or 5 mg/L,whichever is greater Resolution: 0.01 mg/L

Auto Stable User defined auto-stable function holds stable readings on display when criteria is met Barometer Built-in barometer Buffer Recognition Auto buffer recognition for US and NIST buffersCertifications RoHS, CE, WEEE, C-Tick, VCCI, FCC, IP-67, 1-meter drop test, Assembled in USA Connectivity USB 2.0; ProComm II communications saddle and USB cable included; user-upgradeable software via USB and website Connector MS (military spec) waterproof with bayonet lock Data Management Data Manager desktop software included; 100 user-defined folders and site namesData Memory 5,000 data sets (data, date, time, user-defined info); 100 GLP files Dimensions 8.3 cm width x 21.6 cm length x 5.6 cm depth (3.25 in x 8.5 in x 2.21 in)Display Graphic display with detailed Help; backlit display AND keypad DO Membrane Response Times 1.25 mil PE = 8 seconds and 6 in/sec flow(T95; 100%-0) and Flow 2.0 mil PE = 17 seconds and 3 in/sec flowDependence 1 mil Polytetrafluoroethylene (PTFE) = 18 seconds and 12 in/sec flowDO Sensors Polarographic or galvanic field sensors; self-stirring polarographic BOD sensor for the lab Field Cables Standard lengths of 1, 4, 10, 20, or 30 meters - up to 100 meters on DO only cables; all 4-meter and longer cables include a cable management kitFlow Cell Single, dual and multiparameter Quatro cable all flow cell compatible GLP Compliance Yes; detailed GLP information is stored and is available to view, download or printLab Cables BOD sensor includes 2-meter cable; 1 or 4 meters on lab pH, ORP and pH/ORP cables Languages English, Spanish, German, French, Italian, Norwegian, Portuguese, Japanese, Chinese (Simplified & Traditional)Logging Modes Single or Continuous Operating Temperature -10 to 60 °CPower 2 alkaline C-cells provide 80 continuous hours at ambient temperature without backlight; ProComm II saddle provides USB power or optional wall power, cigarette lighter, and universal cell phone charger options Storage Temperature -20 to 70 °CUser ID Optional user ID for data security Warranty 3-year instrument; 2-year field cablesWaterproof IP-67 (even with the battery cover off); floats Weight with Batteries 475 grams (1.05 lbs)

YSI® PRO PLUS MULTIPARAMETER METER SPECIFICATIONS


216 WATER QUALITYMultiparameter

YSI® ProDSS MULTIPARAMETER FIELD SAMPLING INSTRUMENTThe ProDSS Portable Digital Sampling System is designed for use in demanding field applications such as surface water, groundwater, and aquaculture. The rugged and reliable ProDSS allows for measurement of up to 17 parameters. The ProDSS features user-replaceable digital smart sensors that are automatically recognized by the instrument when connected. A backlit color display, large memory, convenient calibration procedures, rechargeable battery, and powerful PC data management program (KorDSS) make the ProDSS user friendly. The optional GPS function, wide range of sensors, and varying cable lengths allow for complete customization of the ProDSS. Mil-spec (military spec) connectors and a waterproof (IP-67), rubber over-molded case ensures durability to provide years of sampling even in the harshest field conditions. 3-year meter warranty; 2 year cable warranty (sensor warranties vary).InstrumentIncludes a rechargeable lithium-ion battery (pre-installed), hand strap, USB cable for charging the ProDSS battery and for connection to a PC, AC charger, cable for connection to a USB memory stick, ProDSS quick start guide, USB software memory stick and digital manual.Cables Cables do not include an integrated temperature sensor. All cables include 4 universal sensor ports and a maintenance kit (3 port plugs, tube of Krytox® lubricant, brush for conductivity probe, syringe for depth sensor, and sensor installation/removal tool). A 1 lb. weight is included with all cables 10 meters and longer while 10, 20, and 30 meter cables include a cable management kit.Probes A conductivity/temperature probe must be installed in a ProDSS cable for accurate measurement of all parameters. All probes, including conductivity/temperature, must be ordered separately.Features:• Measures pH, ORP, dissolved oxygen (optical-based sensor), conductivity, turbidity,

temperature, depth and more.• Digital smart sensors are automatically recognized by the instrument and store calibration data• User-replaceable cables and sensors• KorDSS desktop software (included) and USB on-the-go connector assist with data

management• Rechargeable lithium-ion battery• Color display and backlit keypad; menu-driven operation• Long-life lithium-ion battery; ensures reliability and minimizes waste• Optional GPS, used with KorDSS for Geolocation and visualization of data• Optional depth sensor and up to 100-m cable lengths – great for profiling applications• Large memory (>100,000 data sets) with extensive site list capabilities• Multiple languages: English, Spanish, Portuguese, French, German, Italian, Japanese,

Norwegian, and Chinese• Military spec connectors, waterproof IP67 rating and rubber over-molded case

MODEL EACH

Meter onlyY626870-1 PRODSS METER WITHOUT GPS $1,600.00 Y626870-2 PRODSS METER WITH GPS 2,100.00

Cables with ProbeY626909-1 1M, 4 SENSOR PORTS - NO DEPTH SENSOR $1,720.00 Y626909-4 4M, 4 SENSOR PORTS - NO DEPTH SENSOR 1,770.00Y626909-10 10M, 4 SENSOR PORTS - NO DEPTH SENSOR 1,820.00Y626909-20 20M, 4 SENSOR PORTS - NO DEPTH SENSOR 1,930.00Y626909-30 30M, 4 SENSOR PORTS - NO DEPTH SENSOR 2,030.00Y626909-40 40M, 4 SENSOR PORTS - NO DEPTH SENSOR 2,130.00Y626909-50 50M, 4 SENSOR PORTS - NO DEPTH SENSOR 2,230.00Y626909-60 60M, 4 SENSOR PORTS - NO DEPTH SENSOR 2,330.00Y626909-70 70M, 4 SENSOR PORTS - NO DEPTH SENSOR 2,430.00Y626909-80 80M, 4 SENSOR PORTS - NO DEPTH SENSOR 2,530.00Y626909-90 90M, 4 SENSOR PORTS - NO DEPTH SENSOR 2,630.00Y626909-100 100M, 4 SENSOR PORTS - NO DEPTH SENSOR 2,730.00Y626910-1 1M, 4 SENSOR PORTS - WITH DEPTH SENSOR 2,470.00

MODEL EACH

Cables with Probe (Continued)Y626910-4 4M, 4 SENSOR PORTS - WITH DEPTH SENSOR $2,520.00Y626910-10 10M, 4 SENSOR PORTS - WITH DEPTH SENSOR 2,570.00Y626911-20 20M, 4 SENSOR PORTS - WITH DEPTH SENSOR 2,680.00Y626911-30 30M, 4 SENSOR PORTS - WITH DEPTH SENSOR 2,780.00Y626911-40 40M, 4 SENSOR PORTS - WITH DEPTH SENSOR 2,880.00Y626911-50 50M, 4 SENSOR PORTS - WITH DEPTH SENSOR 2,980.00Y626911-60 60M, 4 SENSOR PORTS - WITH DEPTH SENSOR 3,080.00Y626911-70 70M, 4 SENSOR PORTS - WITH DEPTH SENSOR 3,180.00Y626911-80 80M, 4 SENSOR PORTS - WITH DEPTH SENSOR 3,280.00Y626911-90 90M, 4 SENSOR PORTS - WITH DEPTH SENSOR 3,380.00Y626911-100 100M, 4 SENSOR PORTS - WITH DEPTH SENSOR 3,480.00

ProbesY626900 OPTICAL DISSOLVED OXYGEN (ODO) $999.99Y626901 TURBIDITY 1,100.00Y626902 CONDUCTIVITY AND TEMPERATURE 699.99Y626903 PH WITH MODULE 449.99

3 YEAR METER WARRANTY



WATER QUALITYMultiparameter

217

MODEL EACH

Probes (Continued)Y626904 PH/ORP WITH MODULE 574.99Y626905 NITRATE WITH MODULE 574.99Y626906 AMMONIUM WITH MODULE 574.99Y626907 CHLORIDE WITH MODULE 574.99

Replacement ModulesY626963 PH $169.99Y626964 PH/ORP 249.99Y626965 NITRATE 269.99Y626966 AMMONIUM 269.99Y626967 CHLORIDE 269.99

SolutionsY3167-E 1,000 US/CM PER PINT (FRESH WATER) $19.99Y3168-E 10,000 US/CM PER PINT (BRACKISH WATER) 20.99Y3169-E 50,000 US/CM PER PINT (SALT WATER) 20.99Y3628 ZOBELL ORP TEST 32.99


TEMPERATURE Range: -5 to 70 °C (temperature compensation range for DO mg/L measurement: -5 to 50 °C )Accuracy: ±0.2 °CResolution: 0.1 °C or 0.1 °F (user selectable)Units: °C, °F, K

pH Range: 0 to 14 pH unitsAccuracy: ±0.2 pH unitsResolution: 0.01 pH unitsUnits: pH, pH mV

ORP Range: -1999 to 1999 mVAccuracy: ±20 mVResolution: 0.1 mVUnits: mV

DISSOLVED OXYGEN Range: 0 to 500%, 0 to 50 mg/LAccuracy: 0 to 200%: ±1% of reading or 1% saturation, whichever is greater 200 to 500%: ±8% of reading | 0 to 20 mg/L: ±0.1 mg/L or 1% of reading, whichever is greater | 20 to 50 mg/L: ±8% of readingResolution: 0.01 mg/L and 0.1%, or 0.1 mg/L and 1% (user selectable)Units: % saturation, % saturation local, mg/L, ppm

BAROMETER Range: 375 to 825 mmHgAccuracy: ±1.5 mmHg from 0 to 50 °CResolution: 0.1 mmHgUnits: mmHg, inHg, mbar, psi, kPa, atm

CONDUCTIVITY** Range: 0 to 200 mS/cmAccuracy: 0 - 100 mS/cm: ±0.5% of reading or .001 mS/cm, whichever is greater | 100 - 200 mS/cm: ±1.0% of readingResolution: 0.001, 0.01 or 0.1 μS/cm (range dependent)Units: μS/cm, mS/cm

SPECIFIC CONDUCTANCE*

Range: 0 to 200 mS/cmAccuracy: 0 - 100 mS/cm: ±0.5% of reading or .001 mS/cm, whichever is greater | 100 - 200 mS/cm: ±1.0% of reading. User selectable reference temperature (15 to 25 °C; default 25 °C) and compensation coefficient (0 to 4%/°C; default 1.91%)Resolution: 0.001, 0.01, 0.1 mS/cmUnits: μS/cm or mS/cm

SALINITY* Range: 0 to 70 pptAccuracy: ±1.0% of reading or ±0.1 ppt, whichever is greaterResolution: 0.01 pptUnits: ppt or PSU

TOTAL DISSOLVED SOLIDS*

Range: 0 to 100 g/LAccuracy: Calculated from specific conductance and a user-selectable TDS multiplier (0.30 to 1.00; default 0.65)Resolution: 0.001, 0.01, 0.1 g/LUnits: mg/L, g/L, kg/L

SEAWATER DENSITY* Range: 0.0 to 50.0 sigma, sigma TAccuracy: —Resolution: 0.1 sigma or sigma TUnits: Sigma, Sigma T

TURBIDITY Range: 0 to 4000 FNUAccuracy: 0 to 999 FNU: 0.3 FNU or ±2% of reading, whichever is greater 1000 to 4000 FNU: ±5% of readingResolution: 0.1 FNUUnits: FNU, NTU

TOTAL SUSPENDED SOLIDS*

Range: 0 to 30000 mg/LAccuracy: User correlated from turbidity field measurements and labTSS measurements from grab samplesResolution: 0.01, 0.1 mg/LUnits: mg/L

AMMONIUM***/**** Range: 0 to 200 mg/L NH4-NAccuracy: ±10% of reading or 2 mg/L, whichever is greaterResolution: 0.01 mg/LUnits: NH4-N mg/L, NH4-N mV

CHLORIDE*** Range: 0 to 18000 mg/L ClAccuracy: ±15% of reading or 5 mg/L, whichever is greaterResolution: 0.01 mg/LUnits: Cl mg/L, Cl mV

NITRATE*** Range: 0 to 200 mg/L NO3-NAccuracy: ±10% of reading or 2 mg/L, whichever is greaterResolution: 0.01 mg/LUnits: NO3-N mg/L, NO3-N mV

SEAWATER DENSITY* Range: 0 to 328 feet (0 to 100 m)Accuracy: ±0.013 ft (±0.004 m) for 1, 4, and 10 m cables±0.13 ft (±0.04 m) for cables 20 m and longerResolution: 0.001 m or 0.01 ftUnits: m, ft

MODEL EACH

Solutions (Continued)CAL 4 PH 4.01 13.99CAL 7 PH 7.00 13.99CAL 10 PH 10.00 13.99

AccessoriesY603075 SOFT SIDED CARRYING CASE, LARGE $124.99 Y626945 HARD SIDED CARRYING CASE, SMALL (1 & 4M) 269.99Y626946 HARD SIDED CARRYING CASE, LARGE 349.99Y603070 SHOULDER STRAP 33.59Y603069 BELT CLIP 29.39Y626943 EXTERNAL RECHARGE. LI-ION BATTERY PACK, SMALL 49.99Y626944 EXTERNAL RECHARGE. LI-ION BATTERY PACK, LARGE 79.99Y626942 USB CAR CHARGER, 12VDC 19.99Y599080 FLOW CELL 279.99Y603056 FLOW CELL MOUNTING SPIKE 29.99Y626918 WEIGHT, 1 LB 74.99Y605978 WEIGHT, 4.9 OZ. 33.79

*DERIVED/CALCULATED PARAMETER **RESISTIVITY CAN BE CALCULATED WITH THE CONDUCTIVITY SENSOR ***ISES FOR FRESHWATER ONLY; 20 METER MAXIMUM DEPTH****AMMONIA CAN BE CALCULATED AND REPORTED FROM AMMONIUM, TEMPERATURE, SALINITY, AND PH.



218 WATER QUALITYPhotometer


Y9500

MODEL EACH

Y9300 YSI PHOTOMETER $1,070.00Y9500 PHOTOMETER W/USB CONNECTION 1,380.00

YSI® PHOTOMETERS FW SW

YSI® photometers are sophisticated water quality analysis systems that measure a variety of parameters and provide simple on-screen instructions. Results are available within seconds. IP67-rated waterproof systems use easy-to-use reagent tablets for testing instead of liquids or powder packets. Reagent tablets have an indefinite shelf life when stored in their foil pouches. 5.8" L x 10.8" W x 3" H, ship weight 7 lbs.The Y9300 photometer includes carrying case, light cap, 8 test tubes, dilution tube, 10 crush rods, cleaning brush and instruction manual. Also has backlit graphic display, self-adjusting sample tube holder and on-screen instructions in multiple languages.The Y9500 includes all the above plus a waterproof USB connection, internal memory that holds up to 500 sample sets and a number of user-selectable options such as test units, sample number and dilution factors.

YSI® PHOTOMETER REAGENTS RANGE STARTER KITS REPLACEMENT REAGENTS TEST KITS MG/L MODEL # TESTS EACH MODEL # TESTS EACHALKALINITY-M (ALKAPHOT M) 0-500 YPM250 50 $34.99 YAP250 250 $86.99ALKALINITY-P (ALKAPHOT P) 0-500 YPM251 50 35.99 YAP251 250 86.99ALKALINITY-TOTAL 0-500 YPM188 50 36.99 YAP188 250 78.99ALUMINUM 0-0.5 YPM166* 50 38.99 YAP166* 250 102.99AMMONIA 0-1.0 YPM152 50 51.99 YAP152 250 86.99BROMINE 0-10.0 YPM060 50 33.99 YAP060 250 30.49CALCIUM HARDNESS 0-500 YPM252* 50 36.99 YAP252* 250 89.99CHLORIDE (CHLORIDOL) 0-50 YPM268 50 45.99 YAP268 250 109.99CHLORINE HR 0-250 YPM162* 50 34.99 YAP162* 250 109.99CHLORINE DPD 1 (FREE) 0-5.0 YPM011 50 11.99 YAP011 250 33.99CHLORINE DPD 2 (MONO & DICHL.)** 0-5.0 YPM021 50 14.99 YAP021 250 37.99CHLORINE DPD 1&3 (FREE, COMBINED & TOTAL) 0.5.0 YPM031 50 24.99 YAP031 250 55.99CHROMIUM VI (HEXAVALENT) 0-1.0 YPM281 50 56.99 YAP281 250 140.99COPPER (COPPERCOL) (FREE, COMBINED & TOTAL) 0-5.0 YPM186 50 59.99 YAP186 250 155.99CYANURIC ACID 0-200 YPM087 50 28.99 YAP087 250 64.99FLUORIDE 0-1.5 YPM179 50 48.99 YAP179 200 112.99HARDNESS (HARDICOL) 0-500 YPM254 50 42.99 YAP254 250 102.99HYDROGEN PEROXIDE LR 0-2.0 YPM104 50 24.49 YAP104 250 53.99HYDROGEN PEROXIDE HR 0-100 YPM105 50 31.99 YAP105 250 97.99IRON LR 0-1.0 YPM155 50 28.49 YAP155 250 119.99IRON HR 0-10 YPM156* 50 28.49 YAP156* 250 56.99MAGNESIUM (MAGNECOL) 0-100 YPM193* 50 42.99 YAP193* 250 76.99MANGANESE 0-0.03 YPM173 50 43.99 YAP173 250 102.99MOLYBDATE HR 0-100 YPM175 50 42.99 YAP175 250 109.99NITRATE 0-20 YPM163 50 58.99 YAP163 200 151.99NITRITE (N) 0-0.5 YPM109 50 24.49 YAP109 250 60.99NITRITE (NANO₂) 0-1,500 YPM260 50 40.99 YAP260 250 91.99ORGANOPHOSPHONATE (OP) 0-20 YPM262 50 92.99 YAP262 250 220.99OZONE 0-2.0 YPM056 50 58.99 YAP056 250 51.99PH (PHENOL RED) 6.8-8.4 YPM130 50 17.99 YAP130 250 31.99PHOSPHATE LR 0-4.0 YPM177 50 31.99 YAP177 200 106.99PHOSPHATE HR 0-100 YPM114 50 43.99 YAP114 250 96.99POTASSIUM 0-12 YPM189 50 43.99 YAP189 250 96.99SILICA 0-4.0 YPM181 50 54.99 YAP181 200 128.99SULFATE 0-200 YPM154 50 21.49 YAP154 250 43.99SULFITE 0-500 YPM266 50 38.99 YAP266 250 88.99ZINC 0-4.0 YPM148* 50 55.99 YAP148* 250 147.99*Not recommended for saltwater testing. **Requires YPM031

Can’t find what you’re looking for? See it all at PentairAES.com.

LM1910

SMART3 COLORIMETER FW SW

Ideal for water analysis in the field or in the lab. Easy to use software allows the analyst to choose a test factor from over 80 preprogrammed calibrations for LaMotte reagent systems. The reacted sample is always scanned at the optimum wavelength which is automatically selected from the multiple LED optical system and the test result is presented on the large, backlit display. The test result is displayed directly in units of concentration, as well as Absorbance and %T, in one of seven languages. The analyst also has the option of entering up to 25 additional calibrations for analysis with custom reagent systems. Test factors can be arranged in any of three sequences that can be modified at any time to meet changing testing needs. The data logger holds up to 500 time and date stamped data points. A USB connection allows an interface of the colorimeter with a computer for real-time data acquisition and data transfer. 7.5” L x 3.5” W x 2.5” H. Visit PentairAES.com for more Reagents.

• Large graphical liquid crystal display

• Simple, menu-driven operation• Over 80 pre-programmed tests• Lithium ion rechargeable battery

or computer/wall adapter

• IP67 Waterproof• Data logger for 500 data points• 25 User tests

SHIP WT MODEL (LBS) EACH

LM1910 SMART3 COLORIMETER 2 $998.99

ACCESSORIES/REPLACEMENT ITEMS

LM1910CD SMARTLINK 3 PROGRAM CD 68.990290-6 TEST TUBES WITH CAPS (6) 27.89

2-YEAR WARRANTYFeatures

SYSTEM SPECS

RANGE 0–125% T

RESOLUTION 1% FS

ACCURACY 2% FS

SMART3 REAGENT SYSTEMS Reagents are designed to avoid test interferences, making results fast and dependable. Shipping weight is 1 lb for each reagent. RANGE* MODEL TEST FACTOR TEST METHOD (# OF REAGENTS) (PPM) # OF TESTS EACH

LM3659SC AMMONIA NITROGEN (FRESH WATER) SALICYLATE (3) 0.05 - 1.00 25 $50.59 AMMONIA NITROGEN (SALT WATER) 0.10 - 1.00

LM3642SC AMMONIA NITROGEN HR NESSLERIZATION (2) 0.05 - 4.00 100 43.29

LM3643SC BROMINE LR DPD TABLETS (2) 0.10-9.00 100 57.79 CHLORINE (FREE & TOTAL) DPD TABLETS (3) 0.03-4.00 IODINE DPD TABLETS (2) 0.20-14.00

LM3644SC CHLORINE DIOXIDE DPD TABLET/GLYCINE (2) 0.06-8.00 100 36.09

LM3640SC COPPER BCA - LR BICINCHONINIC ACID (1) 0.04 - 3.50 50 28.89

LM3646SC COPPER DDC DIETHYLDITHIOCARBAMATE (1) 0.10 - 6.00 100 17.89

LM3660SC CYANIDE PYRIDINE-BARBITURIC ACID (5) 0.03 - 0.35 50 104.09

LM3688SC DISSOLVED OXYGEN (DO) WINKLER COLORIMETRIC (3) 0.60-11.00 200 42.39

LM3647SC FLUORIDE SPADNS (2) 0.10-2.00 50 51.39

LM3662SC HYDROGEN PEROXIDE LR DPD (2) 0.02-1.50 100 42.99

LM3648SC IRON BIPYRIDYL (2) 0.10-6.00 50 42.29

LM3668SC IRON - PHENANTHROLINE 1,10 PHENANTHROLINE (2) 0.10-5.00 50 47.09

LM3658SC MANGANESE LR PAN (3) 0.01-0.70 50 63.49

LM369901SC MOLYBDENUM HR THIOGLYCOLATE (3) 0.60-50.00 50 60.09

LM3649SC NITRATE NITROGEN LR CADMIUM REDUCTION (2) 0.10-3.00 20 47.29

LM3650SC NITRITE NITROGEN LR DIAZOTIZATION (2) 0.02-0.80 20 47.29

LM3700SC pH CPR CHLOROPHENOL RED (1) pH 5.00-6.80 100 53.29 pH PR PHENOL RED (1) pH 6.60-8.40 pH TB THYMOL BLUE (1) pH 8.00-9.50

LM3653SC PHOSPHATE LR ASCORBIC ACID REDUCTION (2) 0.05-3.00 50 39.99

LM3655SC PHOSPHATE HR VANADOMOLYBDOPHOSPHORIC ACID (1) 0.50-70.00 50 22.99

LM3639SC POTASSIUM TETRAPHENYLBORON (2) 0.80-10.00 100 61.99

LM3664SC SILICA LR HETEROPOLY BLUE (4) 0.05-4.00 100 58.69

LM3687SC SILICA HR SILICOMOLYBDATE (3) 1.00-75.00 50 44.09

LM3665SC SULFATE HR BARIUM CHLORIDE (1) 3.00-100.00 100 30.89

LM3654SC SULFIDE LR METHYLENE BLUE (3) 0.06-1.50 50 69.29

LM3666SC TANNIN TUNGSTO-MOLYBDOPHOSPHORIC ACID (2) 0.10-10.00 50 54.69

LM3667SC ZINC LR ZINCON (6) 0.05-3.00 50 117.09

*Range may be extended by dilution in most cases.

WATER QUALITYColorimeter

219



REAL UVT TECHNICAL SPECIFICATIONS

UV WAVELENGTH 253.7 nm

SOURCE Low pressure germicidal UV lamp

RANGE 5 - 100 % Transmittance, 0 – 1.3 Absorbance

ACCURACY 0.5% UV Transmittance

RESOLUTION 0.1% Transmittance, 0.001 Absorbance

UNITS OF MEASUREMENT UV Percent Transmittance (%), UV Absorbance per cm (cm-1)

BUILT-IN FAULT DETECTION SYSTEM Noti fication of a system failure

DISPLAY 32 character back-lit LCD digital display provides easy on screen instructions and system messages

CALIBRATION MEMORY Calibration memory technology. Calibration with DI water required only periodically.

RESPONSE TIME Warm-up Time ~ 1 minute, Calibration ~ 2 seconds, Computation ~ 2 seconds

OPERATING TEMPERATURES 0 – 45 °C (32 – 113 °F)

CASE Rugged, Compact, Watertight, and Dustproof with convenient carrying handle

SAMPLE CELL 10 mm x 10 mm quartz cuvette

PATH LENGTH 1 cm

POWER SUPPLY • Wall Adapter – 110 VAC (UL approved) or 220 VAC, Car Adapter – 12 VDC

• Battery power pack option

DIMENSIONS 8.7” L x 7.5” W x 3.9” H (254 cu in)

WEIGHT 4 lbs

2-YEAR WARRANTY

UVT FIELD METERWith innovative Split-Sense technologyKey Features• UV 254nm wavelength• Memory calibration—no field zeroing needed• Performs both UVT and UVA measurements• Portable and easy to use• Battery powered option• 1 minute warm-up time• Extreme accuracy• 2-year warranty

The Real UVT field meter with exclusive Split-Sense technology is the world’s most advanced and affordable portable UV254 testing meter, guaranteed. The portable Real UVT meter can quickly and accurately test UV254 in the field within minutes. The Real UVT meter utilizes Real Tech Inc.’s Split-Sense technology to give it many advantages such as its fast 1 minute warm-up time and extreme accuracy.Split-Sense technology works by using a single beam of UV light to take continuous readings before and after the insertion of the quartz cuvette allowing for compensation of the effects of UV lamp drift and fluctuations.The Real UVT meter’s new calibration memory feature allows testing to be performed without the need to zero the meter with 100% DI water even if the meter has been powered off.

Measuring OrganicsUV254 provides an indication of the amount of natural organic matter (NOM) in water and wastewater. More specifically, UV254 is the best detector of aromatic organics or reactive NOM.Aromatic organics are problematic, having several negative effects. For example, when combined with chlorine, aromatic organics readily form disinfection by-products (DBPs).The Real UVT field meter is the ideal solution for testing UV254 anywhere, anytime. The Real UVT can also be used as a practical alternative or supplement to measuring other more expensive and complicated organic test parameters such as TOC, DOC, BOD and COD.

Beneficial Applications Include• Coagulation optimization • Filter performance• DBP formation potential • UV disinfection• Effluent monitoring • Plant security/safety• Process control

Calibration MemorySplit-Sense technology provides the unique advantage to remember the meters calibration, so calibrating or zeroing the meter before each use is not required. This elimates the need for carrying pure 100% DI water in the eld, furthering the meters ease of use.

Fast Warm-Up Time The Real UVT’s exclusive Split-Sense technology allows for a fast warm-up time of only 1 minute.

Accuracy & RepeatabilityAlthough the Real UVT meter has been designed to cope with the harsh conditions encountered in the fi eld, its extreme accuracy and repeatability make it a valuable addition to any water analysis laboratory.

MODEL EACH

P200UV254 REAL TECH P200 UV254 METER $1,937.001UVT060020 REPLACEMENT LAMP, P SERIES 141.491UVT045010 REPLACEMENT CUVETTE. QUARTZ, 10 MM 262.89

220 WATER QUALITYUVT Meter




221


2020WE/WI PORTABLE TURBIDITY METERSIndustry-leading precision, sensitivity, and dependability in one of the most innovative handheld meters available on the market — NOW WATERPROOF!The multi-detector optical configuration assures long term stability and minimizes stray light and color interferences. All readings are determined by the process of signal averaging over a 5-second period. This minimizes fluctuations in readings attributed to large particles and results in rapid, highly repeatable measurements. Ideally suited for both low-level drinking water applications, as well as monitoring high turbidity in the field.Kits are supplied with 0, 1, and 10 NTU standards, sample bottle, six sample tubes, USB cable, wall adapter and waterproof case.• Seven user selected languages – English, Spanish, French, Japanese,

Chinese, Italian, and Portuguese• Advanced calibration algorithms• Easy menu driven operation and large LCD display• 500 point data log; stored results can be viewed directly on instrument

or downloaded to a computer via USB cable and SmartLink 3 software (available separately)

• Waterproof to IP67• Lithium rechargeable batteries

SHIP WT MODEL (LBS) EACH

LM1970 2020WE KIT (MEETS EPA 180.1) 6 $978.99LM1970-ISO 2020WI KIT (MEETS ISO 7027) 6 978.99

ACCESSORIES/REPLACEMENT ITEMS

LM1910CD SMARTLINK 3 PROGRAM CD 68.990290-6 TEST TUBES WITH CAPS (6) 27.89

TURBIDITY SPECIFICATIONS

Unit of Measure 2020we NTU, AU, ASBC, EBC

Units of Measure 2020wi FNU, FAU, ASBC, EBC

Range* 0-4000 NTU/FNU, 0-10,500 ASBC, 0-150 EBC

Resolution* 0.01 NTU/FNU 0.00-10.99 0.1 NTU/FNU 11.0-109.9 1 NTU/FNU 110-4000

Accuracy* From 0-2.5 NTU the accuracy is ±0.05 NTU From 2.5-100 NTU the accuracy is ±2% Above 100 NTU the accuracy is ±3%

Detection Limit 0.05 NTU/FNU

Range Selection Automatic

Reproducibility* .02 NTU/FNU or 1%

Light Source Tungsten (EPA), complies with EPA 180.1, Rev. 2.0 (1993) and Standard Methods 2130 B-2001; 860nm LED (ISO), complies with ISO 7027

*over 600 NTU/FNU units expressed as AU/FAU

METER FEATURES

Signal Averaging Disabled, 2, 5, 10

Power USB computer cable, wall adapter or Lithium ion rechargeable battery, 3.7V, 2.5” x .75”, 1.7 oz

AC Power Optional

Data Logging 500 points

Auto Shut-Off Disabled, 5, 10, 30 seconds

Optional Software SmartLink 3

Languages English, French, Spanish, Japanese, Italian, Portuguese,Chinese

Response Time <2 Seconds

Size 7.5 x 3.5 x 2.5 inches; 19.05 x 8.84 x 6.35 cm

Weight 13 ounces

Display 6-line LCD with backlit display; 160 x 100 backlit LCD; 20 x 6 line graphics

0290-6

LM1970


221WATER QUALITYTurbidity Meters

221



222

pHMODEL EACH

MW4 PH 4.01 25 X 20 ML SACHETS $25.79MW7 PH 7.01 25 X 20 ML SACHETS 25.79MW10 PH 10.01 25 X 20 ML SACHETS 25.79MW5 (10) PH 7.01, (5) PH 4.01, 10.01 AND H₂O 25 X 20 ML SACHETS 25.79

Conductivity

MA9061 1.413 ΜS/CM EC SOL . 230 ML BOTTLE 9.19

D.O.

MA9070 ZERO O₂ SOL. 230 ML BOTTLE $15.79 MA9071 O₂ ELECTROLYTE SOL. 230 ML BOTTLE 24.19

Care and Storage

MA9015 PH/ORP STORAGE SOL. 230 ML BOTTLE $9.19 MW0 DEIONIZED WATER 25 X 20 ML SACHETS 25.79

CALIBRATION SOLUTIONSThe easiest way to calibrate a pen or meter in the fieldMilwaukee standard calibration solutions are available in 230-mL bottles and 20-mL sachets. Traditional buffer solutions are packed in 230-mL leak-proof bottles and are recommended for lab application. Sachets are sealed against light and air and are ideal for on-the-spot calibration. Simply open, insert the tester or electrode into the sachet and calibrate. Sachets are sold in boxes of 25 pieces.


222 WATER QUALITYCalibration Solutions

CONNECT WITH US

/PentairAES /PentairAES /PentairAES /PentairAES/aquatic-eco-systems-inc/AquaticEcoTV



223WATER QUALITYCalibration Solutions

223

CS

CAL7 CAL10CAL4

ELECTRODE CARE ACCESSORIESElectrode cleaning solution will safely clean pH/ORP electrodes. Use pH storage solution with the electrode saver bottle. Fill saver bottle with storage solution. Accepts probes up to 12 mm in diameter and protects the electrode. Use rinse solution between each reading for greater accuracy.

MODEL EACH

CS PH/ORP CLEANING SOLUTION, 1 PINT $12.99SS PH/ORP STORAGE SOLUTION, 1 PINT 17.29SBT SAVER BOTTLE 6.49VSDI RINSE SOLUTION, 1 QUART 17.29

PH CALIBRATION SOLUTIONS500-mL bottles

CONDUCTIVITY CALIBRATION SOLUTIONS NIST-traceable conductivity solutions to calibrate both field instruments and lab instruments and cells together for maximum accuracy. 1 pint bottles.

MODEL EACH

Y3167-E 1,000 US/CM PER PINT (FRESH WATER) $19.99Y3168-E 10,000 US/CM PER PINT (BRACKISH WATER) 20.99Y3169-E 50,000 US/CM PER PINT (SALT WATER) 20.99

MODEL EACH

CAL4 PH 4.01 $13.99CAL7 PH 7.00 13.99CAL10 PH 10.00 13.99




224 WATER QUALITYTest Kits

FRESHWATER FISH FARM 9 TEST KIT FW TECH FAV HAZMAT AG

Here are the most common water quality parameters tested by freshwater fish farmers— in one rugged carrying case. The kit features deluxe octa-slide comparators by LaMotte®. An armored thermometer (-5 to 45°C) is included. Kit weighs 10 lbs, refill kit weighs 0.5 lb.

LMAQ4

LMAQ2

LaMotte® is a registered trademark of LaMotte Chemical Products Co.

TEST RANGE

AMMONIA NITROGEN 0.05-2.0 ppm

NITRITE 0.05–0.8 mg/L

PH 0–200 mg/L

ALKALINITY 0 to 240 ppm

CARBON DIOXIDE 0–50 mg/L

CHLORIDE 0–200 mg/L

DISSOLVED OXYGEN 0–10 mg/L

HARDNESS 0–200 mg/L

TEMPERATURE -5–45°C

TEST RANGE

AMMONIA NITROGEN 0.05-2.0 ppm

NITRITE NITROGEN 0.25–10 ppm

PH 5.0–10.0

NITRATE NITROGEN 0.05–10 ppm

ALKALINITY 0–200 ppm

CARBON DIOXIDE 0–50 ppm

DISSOLVED OXYGEN 0–10 ppm

SALINITY 0–20 ppt

TEST RANGE

AMMONIA 0.0-2.0 ppm

NITRITE 0.05-0.8 ppm

NITRATE 0.25-10.0 ppm

PH 5.0-10.0

IRON, FERROUS & FERRIC 0.5-10.0 ppm

ALKALINITY 0-200 ppm

DISSOLVED OXYGEN 0-10 ppm

SALTWATER FISH FARM 9 TEST KIT SW HAZMAT A

This kit measures eight different parameters. Salinity can read to 40 ppt by diluting half the sample and doubling the final readings. Includes armored thermometer. Kit and reagent refill contains enough reagents for 50 tests each. Kit weighs 10 lbs, refill 1 lb.

REAGENT REFILLSFor LMAQ2, LMAQ3 and LMAQ4.

MODEL EACH

LMAQ4 SALTWATER TEST KIT $298.99LMAQ4RP REAGENT REFILL 158.69

MODEL EACH

LMAQ2 FISH FARM 9 TEST KIT $239.99LMAQ2RP REAGENT REFILL KIT 146.29

MODEL EACH

LM6R HARDNESS 25.89LM7R NITRITE 38.89LM3353RP PH 6.69LM9R SALINITY HAZMAT A 38.99LM10R NITRATE 44.09

MODEL EACH

LM1R ALKALINITY $18.39LM2R AMMONIA FOR LMAQ2 & LMAQ3 HAZMAT A 31.69LM3304RP AMMONIA FOR LMAQ4 HAZMAT A 34.99LM3R CARBON DIOXIDE 15.79LM4R CHLORIDE HAZMAT A 32.59LM5R DISSOLVED OXYGEN 45.19

AQUAPONICS TEST KIT Designed for small to midsize systems, this test kit has everything you will need to monitor water quality for both the aquaculture and hydroponics segments of your system. Kit includes labware, accessories and reagents to repeat tests for each factor approximately 50 times, a detailed instruction manual and quick reference card in a foam-lined carrying case. Test chemistries and comparators are compatible with fresh, brackish, or salt water systems. Ship weight 9 lbs.

MODEL EACH

LM3637 AQUAPONICS TEST KIT $298.99LM3637RP REAGENT REFILL KIT 138.99

NEW!



225WATER QUALITYTest Kits

225

TEST RANGE

ALKALINITY 6.4–136 mg/L

AMMONIA* 0–3 mg/L


CHLORIDE 5–400 ppt

DISSOLVED OXYGEN* 0.2–20 mg/L

HARDNESS 17–510 mg/L

NITRITE 0–0.5 mg/L

PH 4–10

TEMPERATURE -30–120°F

HACH AQUACULTURE TEST KIT FF1A FW HAZMAT A

This popular freshwater aquaculture test kit includes all the necessary apparatuses and reagents for 100 tests each of nine critical parameters. The kit uses the drop- count method for titration tests and Hach® color comparators for colorimetric tests. Colorimetric tests provide results directly in mg/L and drop-count tests require, at most, a simple multiplication or division step to determine concentration. Ship weight 10 lbs.

MODEL EACH

FF1A AQUACULTURE TEST KIT $341.29

HACH AQUACULTURE TEST KIT FF2A FW HAZMAT A

Similar to the FF1A, the FF2A has an additional test kit to measure for acidity. Designed for freshwater applications only, the kit uses convenient, concentrated titrant solutions in disposable cartridges and has an easy-to-read digital titrator that guarantees repeatability from test to test. Ship weight 12 lbs.

TEST RANGE

ACIDITY 100–4,000 mg/L

ALKALINITY 100–4,000 mg/L

AMMONIA* 0–3 mg/L



DISSOLVED OXYGEN* 0–10 mg/L

HARDNESS 100–4,000 mg/L


PH 4–10


TEST RANGE

ACIDITY 100–4,000 mg/L

ALKALINITY 100–4,000 mg/L

AMMONIA* 0–3 mg/L



DISSOLVED OXYGEN* 0–10 mg/L

HARDNESS 100–4,000 mg/L


PH 4–10


HACH SALTWATER TEST KIT FF3A SW HAZMAT A

Hach® model FF3A test kit is designed specifically for saltwater applications. The kit uses a digital titrator and includes detailed instructions. Enough reagents and apparatuses for 100 tests each. Ship weight 10 lbs.

MODEL EACH

FF2A AQUACULTURE TEST KIT $617.49

MODEL EACH

FF3A SALTWATER TEST KIT $658.79

Hach® and Be Right™ are trademarks and/or registered trademarks of Hach Co.



226 WATER QUALITYAquaculture Laboratories

MODEL EACH

AAL1* $1,583.00

Each kit includes:• YSI 550A D.O. meter (Y550A12) • Hach alkalinity test strips (H27448)• Salinity refractometer (SR5-AQ) • Hach hardness test strips (H27452)• Pocket dial thermometer (TH4) • LaMotte nitrite test kit (LM3352)• LaMotte ammonia test kit (LM4795) • pH/Temp Tester (WD-35634-20)

AQUACULTURE ANALYSIS LABORATORY HAZMAT A

Highly recommended for the serious field professional, this kit includes most things a fish farmer needs to monitor water quality. The portable lab analyzes the 8 critical factors most commonly required by a fish farmer: dissolved oxygen, pH, temperature, salinity, nitrite, ammonia, hardness and alkalinity. Excellent for both fresh and saltwater analyses. Designed with field analysis as a priority, the outfit is packaged in a durable, waterproof Pelican™ case that is foam-lined and holds the components in place. See part numbers for individual reagents.

TEST RANGE

DISSOLVED OXYGEN 0 to 20 mg/L; 0 to 200% Sat

TEMPERATURE 0 to 230°F, -18 to 110°C

PH 0 to 14.00

ALKALINITY 0 to 240 ppm

HARDNESS 0 to 425 ppm

AMMONIA 1 to 8 mg/L

NITRITE 0.1 to 0.8 mg/L

TEST RANGE

ACIDITY 10 - 160 mg/L 100 - 4,000 mg/L

ALKALINITY 10 - 4,000 mg/L

AMMONIA 0 - 0.50 mg/L

CARBON DIOXIDE 10 - 1,000 mg/L

CHLORIDE 10 - 10,000 mg/L

DISSOLVED OXYGEN 0 - 15.0 mg/L

HARDNESS 10 - 4,000 mg/L

IRON 0 - 3.00 mg/L

NITRATE 0 - 30.0 mg/L

NITRITE 0 - 0.350 mg/L

PHOSPHORUS 0 - 2.50 mg/L

TEMPERATURE 0 to 80 ° C

CEL COMPLETE AQUACULTURE LABORATORYThis kit provides instruments and chemicals for 15 tests critical to effective aquatic livestock management whether used in your mobile lab or at the field site. Premeasured reagents are impervious to environmental contamination, apparatus and labware. Instruments have battery power option so tests can be run immediately without concern for sample preservation and handling. With this kit, there is no waiting for hours or days for a lab result. Kit includes DR 900 Colorimeter, HQd pH meter and probe, Digital Titrator, TDS Pocket Tester, reagent sets, apparatus, illustrated instrument manual and procedure manual CD in a sturdy field case. Ship weight 10 lbs.

FW SW HAZMAT A

Ammonia TestingAmmonia is the primary waste byproduct of protein consumption, and is excreted across fish gills as a gas. It may exist in two forms: un-ionized (NH3) and ionized (NH4+). Ionized ammonia is relatively harmless, but gill burn may occur when un-ionized ammonia is present in the water. The amount of un-ionized ammonia relies heavily on pH and temperature. Un-ionized ammonia can be removed via a water change, detoxified with the use of a water conditioner and/or consumed by an established biological filter. Since un-ionized ammonia is toxic to fish, ammonia detection is an important of successful aquaculture. Three types of test are can be used in aquaculture to detect ammonia: Nessler-based, salicylate and hydrophobic membranes.Nessler-based test kits test total ammonia only. They are best used when no other substances are added to the water. Water conditioners, amines and various types of medications can interfere with Nessler-based test readings, resulting in falsely high ammonia readings.Salicylate-based test kits test for total ammonia. This is the most commonly used ammonia test in aquaculture, and will provide results in the presence of water conditioners and various medications.Hydrophobic membrane testing uses a chemically treated membrane to detect various gases. The membrane can be treated with reagents specific to un-ionized ammonia. Hydrophobic membranes can detect free ammonia even in the presence of water conditioners, amines and salts because free ammonia exists as a gas. This is not the most commonly used test, but it is very efficient in free ammonia detection.The test kit instructions should indicate which testing method the kit purchased is using to detect ammonia levels. More and more aquarists choose salicylate-based ammonia test kits due to accessibility, reliability and the ability to dose water conditioners without interference..

TECH TALK 132

MODEL EACH

H251233 AQUACULTURE TEST KIT $2,986.002691700 REAGENT REFILL KIT 1,304.00

*Not for shipment into Canada.Pelican™ is a trademark of Pelican Products, Inc.



227

TEST STRIPS FW SW

Each vial of test strips features a leakproof, hinged, pop-top lid and a wrap-around desiccant liner to protect strips from moisture intrusion. The multi-strips have 5 different tests (alkalinity, pH, nitrite, nitrate and hardness) on one strip. Test strips are both fresh and salt water compatible.

TEST STRIPS FW SW

These small test strips provide a rapid means of checking water quality. Simply dip a strip into the sample, wait for color to develop and compare color on the reagent pad to the color chart on the bottle.

MODEL TEST FACTOR RANGE (PPM) STRIPS/VIAL EACH

H27448 ALKALINITY 0–240 50 $12.09H27553 AMMONIA 0–6 25 24.09H27450 FREE AND TOTAL CHLORINE* 0–10 50 22.49H27451 COPPER 0–3 25 24.59H27452 TOTAL HARDNESS* 0–425 50 12.79H27453 TOTAL DISSOLVED IRON 0–5 25 24.59H27454 NITRATE/NITRITE 0–50 / 0–3 25 20.79H27456 PH* 4–9 50 12.69H27571 PHOSPHATE* 0–50 50 23.29

*Can be used with salt water.

H27448

TEST STRIPSIndividual pads on a polystyrene strip. These are packaged in the pop top vial which is molded with a desiccant liner for protection from moisture. The vial has a molded desiccant liner that protects the strips from moisture intrusion and eliminates loose desiccant bags.

LM2999LR

R442

MODEL TEST FACTOR RANGE (PPM) STRIPS/VIAL EACH

LM2999LR CHLORINE DIOXIDE 0-10 (0, 0.25, 0.5, 1, 3, 5, 10) 50 $9.99LM3002 CHLORINE DIOXIDE 0-500 ( 0, 10, 25, 50, 100, 250, 500) 50 9.99LM2963LR-G CHLORINE, TOTAL, LOW RANGE 0-10 (0, 0.25, 0.5, 1, 3, 10) 25 5.89LM4250BJ CHLORINE, TOTAL 10-200 (10, 50, 100, 200) 200 5.99LM3031 CHLORINE, FREE, HIGH RANGE 0-800 (0, 50, 100, 250, 500, 800) 50 17.09LM2984LR HYDROGEN PEROXIDE 0-50 (0, 1, 3, 10, 30, 50) 25 9.99LM2948BJ IODINE 12-100 (12, 25, 50, 100) 200 5.99LM3000LR PERACETIC ACID, LOW RANGE 0-50 (0, 5, 10, 20, 30, 50) 50 9.39LM3021LR PHOSPHATE, LOW RANGE 0-2.5 (0, 0.1, 0.2, 0.3, 0.5, 1.0, 2.5) 25 19.29LM2934 QAC DUAL RANGE LOW: 0, 10, 20, 40, 80 HIGH: 0, 100, 200, 400, 800 50 7.59LM2951 QAC 50-400 (50, 100, 200, 400) 100 5.79LM2951HR QAC, HIGH RANGE 200-1500 (200, 400, 600, 1,000, 1,500) 50 7.59

LaMotte® is a registered trademark of LaMotte Chemical Products Co.

LM3002 LM3000LR LM2951HRLM3031

WATER QUALITYTest Strips

227

NEW

RANGE MODEL TEST FACTOR (PPM) STRIPS/VIAL EACH

R443 AMMONIA 0–6 25 $14.09R442 MULTI-STRIP 25 13.49



228 WATER QUALITYTest Kits

ALKALINITYAlkalinity refers to the quantity and type of compounds present in the water that shift the pH above 7.0. Water with high alkalinity tends to be more strongly buffered. Buffering will reduce the tendency of the pH to shift. Add sodium bicarbonate to increase alkalinity (buffering capacity) and calcium chloride for hardness. Testing takes 2 minutes. Range: 0 to 200 ppm.

AMMONIA-NITROGENTo know how toxic ammonia is to your fish, you must know the ammonia level, the pH level and the temperature. A total ammonia level of 10 ppm may not be harmful to trout at a pH of 6.0, but it would be deadly if the pH were 7.0. The test kits measure total ammonia. Total ammonia consists of both nontoxic NH4+ (ionized) and toxic NH3 (un-ionized) forms. The proportion of one to the other is variable. The toxic form increases in proportion as the pH and/or temperature increases. Ammonia builds up in the water primarily by the metabolism of protein (nitrogen). About 10% of the protein fed to fish will show up as ammonia in the water. Testing takes 5 minutes. LM4795 range: 1 to 8 ppm. LM3351-01 range: 0.2 to 3 ppm. Note: Water containing Ammo Lock® and other ammonia-removing chemicals should be tested using an ammonia kit (LM3304) that uses the salicylate method (0 to 2.0 ppm).

CALCIUM HARDNESSBecause calcium and magnesium are both major components of the total hardness of water, measuring hardness by itself may not reveal enough. Recirculating aquaculture systems need calcium levels greater than 50 ppm to maintain a fully functional biofilter. Testing takes 2 minutes. 0 to 200 ppm.

CARBON DIOXIDECarbon dioxide (CO2) is present in water as a dissolved gas, like oxygen. High CO2 can stress and even kill fish. It also forms carbonic acid, which lowers the pH. Testing takes 2 minutes. 0 to 50 ppm.

TEST KIT REPLACEMENT REAGENT MODEL EACH MODEL EACH

LM7297 $39.39 LM7297RP $13.39

CHLORIDEChloride is one of the major anions found in water. When using salt, be careful where discharge occurs. Salt water is about 16,000 ppm chloride; it takes only about 500 ppm chloride to kill some plants, shrubs and trees. For freshwater use only. Takes two minutes. 0 to 200 ppm.


LM4503 FW HAZMAT A $46.29 LM4503RP HAZMAT A $28.49

CHLORINEChlorine and chloramines (chlorine/ammonia complex) are toxic to fish, and the presence of one or the other can be expected in your municipal water supply. For aquaculture applications, chlorine should be removed chemically, by aeration or by aging. Chloramines must be removed chemically. For testing fresh water only. Testing takes 2 minutes. Range: 0.2 to 3.0 ppm.


LM3308 FW $66.59 LM3308RP $20.29

COPPERCopper as copper sulfate is often used in fish culture as an algaecide, but it can be lethal to fish at low levels, especially with low pH and alkalinity levels. It can be very toxic to juvenile clams and other invertebrates, particularly saltwater species. Testing takes one minute. Range: 0.05 to 0.5 ppm.


LM6616 $89.99 LM6616RP $6.59

pH KIT (See Pg. 229)

LAMOTTE® TEST KITSLaMotte® brand water test kits have been in use for over 50 years. They are accurate, inexpensive and suitable for both fresh and saltwater testing (except when noted). Each kit (and replacement reagent) contains enough reagent to run between 50 and 200 tests, depending upon the amount of reagent used to reach the end point. All single kits are approximately 2 lbs.

ALKALINITY KIT

*Not for shipment into Canada.


LM4491 $35.59 LM4491RP $15.99


LM3351-01* HAZMAT A $73.79 LM3351-01RP* HAZMAT A $25.69 LM3304 HAZMAT A 78.99 LM3304RP HAZMAT A 34.99 LM4795* HAZMAT A 72.69 LM4795RP* HAZMAT A 23.59


LM3609 $46.79 LM3609RP $19.99



229SECTIONProducts / Products / Products


WATER QUALITYTest Kits

229

DISSOLVED OXYGENThis kit provides an inexpensive alternative to a dissolved oxygen meter. Testing takes 5 minutes. 0 to 10 ppm.


LM5860 $51.99 LM5860RP $31.59

HARDNESSThe total hardness of water generally represents the total concentration of dissolved calcium and magnesium ions. Although closely related to alkalinity and the buffering capacity of water, high alkalinity may not always indicate high hardness. Hard waters (above 150 ppm) are generally more productive for fish than soft waters. The typical range for aquaculture is 50 to 200 ppm. Testing takes 2 minutes. 0 to 200 ppm.


LM4482 $44.59 LM4482RP $18.69

IRONWell water often contains high concentrations of ferrous iron (iron in solution). Concentrations as low as 0.2 ppm can be harmful to certain species of fish. To remove iron, aerate the water and then settle or filter out the resulting orange iron oxide particles. Testing takes two minutes. Range: 0.05 to 1 ppm.


LM7787 $98.29 LM7787RP $19.99

NITRATE, LOW LEVELThis is the final nitrogen product formed by bacterial oxidation of ammonia. Although it is not usually considered a threat to freshwater fish, it is a plant nutrient and can harm marine invertebrates. Testing takes 12 minutes. Range: 0.25 to 10 ppm.


LM3319 HAZMAT A $74.59 LM3319RP $30.29LM3354 56.49 LM3354RP 20.59

LaMotte® is a registered trademark of LaMotte Chemical Products, Co.

NITRITEThis is an intermediate compound formed in the oxidation (nitrification) process of ammonia becoming nitrate. Nitrite can become toxic in recirculating systems. Nitrites interfere with the ability of the fish's blood to take up oxygen (levels as low as 0.2 ppm can cause "Brown Blood" problems with catfish). Testing takes 5 minutes. Range: 0.05 to 0.8 ppm.


LM3352 $83.09 LM3352RP $25.89

PHThis is a measure of hydrogen ion concentration, or more simply, whether the solution is acidic or basic. Units 0 to 6.9 are referred to as acid or acidic. Units of 7.1 to 14 are considered basic and pH 7.0 is neutral. Takes 2 minutes. Range: 5.0 to 10.0; LM2159-01 range: 7.7 to 8.4 (Cresol Red).


LM3353 FW $48.89 LM3353RP $6.69LM2159-01 SW 63.49 LM2159-01RP 14.79

PHOSPHATEPhosphates enter water supplies from wastewater treatment, sewage, soil runoff, fish foods, etc. Although necessary for biological processes, too much phosphate may cause excessive growth of algae and plants. Testing takes 5 minutes. For fresh and salt water. Range: 0 to 2.0 ppm.


LM3121-02 $88.99 LM3121-02RP $23.99

SALINITY TITRATIONFor measuring both low and high salinity levels in ponds, recirculating systems, brackish waters, etc. Testing takes 5 minutes. 0 to 20 ppt (parts per thousand) in 0.4 increments.


LM7459 $62.29 LM7459RP $37.69

SULFIDEFor measuring hydrogen sulfide (toxic to fish), the most common form of sulfide. Testing takes 2 minutes. Range: 0.2 to 20 ppm.


LM3322 $58.49 LM3322RP $23.59

NITRATE, LOW LEVEL KIT PHOSPHATE KIT

HAZMAT A

water quality products - pentair · 220 uvt meter 221 turbidity meter 222 calibration solutions 224...

Documents