warning...warning illustration 1 illustration 2 retaining tab file drawer box drawer shoulder dowel...
TRANSCRIPT
MODULAR FURNITURE
Wood products are heavier than they appear and may be hard to control when moving. Use two or more people when moving wood products or severe personal injury may result.
Read all instructions and review illustrations before installing.
Tools required for assembly: Phillips screwdriver Rubber mallet
Drawer Removal:
1. Lateral drawer removal (refer to Illustration 1):
Completely open drawer.
On each drawer slide, locate screw next to drawer retai-ning tab. Use the Phillips screwdriver to remove screws.
On each side of drawer, press in on drawer retaining tabs and lift up on drawer front. Set drawer aside.
2. Box drawer removal (refer to Illustration 2):
Completely open drawer.
On each side of drawer, press in on drawer retaining tabs and slide drawer forward. Set drawer aside.
3. File drawer removal (refer to Illustration 2):
Completely open drawer.
On each side of drawer, press in on drawer retaining tabs and slide drawer forward. Set drawer aside.
End Panel to Top Assembly:1. Refer to Illustration 3.Lay top,with holes up,on cardboard or a carpeted surface.
Use the Phillips screwdriver to install three minifix bolts (from hardware pack) onto top as shown. Tighten each minifix bolt until minifix bolt shoulder is flat against surface of top.
Use the rubber mallet to install two dowels ( from hard-ware pack) into large holes inline with minifix bolts.
2420708800ESIDE 1 OF 9 (03/2018)
WARNING
Illustration 1
Illustration 2
Retaining tab File drawer
Box drawer
ShoulderDowel
Illustration 3
Minifix bolt
Front edge of top
Drawer retaining tab
Screw
Drawer slide
Illustration 4
Minifix cam hole
End panel
Minifix bolt
Front edge of top
2. Refer to Illustration 4. Attach end panel to top by inserting minifix bolts, attached to top, into holes drilled into top edge of end panel.
Ensure minifix cam holes along top edge of end panel are facing towards top.
Heavy panels can pinch or crush fingers. Do not placefingers between or under panels during assembly.
2420708800ESIDE
2 OF 9 (03/2018)
Illustration 5
Illustration 6
4.
Refer to Illustration 6. Thread a glide (from hardware pack) into each glide insert (from hardware pack) by turning glide clockwise until glide is flat against insert.
Locate holes in bottom of end panel. Install a glide/glide insert into each hole along bottom edge of end panel. Use the rubber mallet to install a glide/glide insert assembly into hole.
Top
Minifix cam
Arrow
End panel
~
~
Threaded insert
Leveling glide
End panel
3. Refer to Illustration 5. With arrows facing top, install three minifix cams (from hardware pack) into holes along top edge of end panel. Note: minifix cams will be recessed into panel approximately 1/4”. Use the Phillips screwdriver to tighten minifix cams. Turn minifix cams clockwise to tighten.
Illustration 7
Minifix bolt
Shoulder
Dowel
Front edge of top
Illustration 8Pedestal
Minifix bolt Front edge
of top
Pedestal to Top Assembly:1.
Refer to Illustration 7. Lay top,with holes up,on cardboard or a carpeted surface.
At desired location, use the Phillips screwdriver to install six minifix bolts (from hardware pack) onto top as shown. Tighten each minifix bolt until minifix bolt shoulder is flat against surface of top.
Use the rubber mallet to install four dowels (from hardware pack) into large holes inline with minifix bolts.
2.
Refer to Illustration 8. Refer to drawer removal instructions and remove drawers from pedestal.
Attach pedestal to top by inserting minifix bolts, attached to top, into holes drilled into top edge of pedestal.
2420708800ESIDE
3 OF 9 (03/2018)
Illustration 9
TopMinifix camArrow
Pedestal
~
~
3.
Refer to Illustration 9. With arrows facing top, install six minifix cams (from hardware pack) into holes along top edge of each side of pedestal. Use the Phillips screwdriver to tighten minifix cams. Turn minifix cams clockwise to tighten.
4.
Refer to Illustration 10. Thread a glide (from hardware pack) into each glide insert (from hardware pack) by turning glide clockwise until glide is flat against insert.
Locate holes in bottom of pedestal. Install a glide/glide insert into each hole along bottom edge of pedestal. Use the rubber mallet to install a glide/glide insert assembly into hole.
Lateral File/Door Unit to Top Assembly:1. Refer to Illustration 11. Lay top, with holes up, on card-
board or a carpeted surface. At desired location, use the Phillips screwdriver to
install six minifix bolts (from hardware pack) onto top as shown. Tighten each minifix bolt until minifix bolt shoulder is flat against surface of top.
Use the rubber mallet to install four dowels (from hard-ware pack) into large holes inline with minifix bolts.
2.
Refer to Illustration 12. Refer to drawer removal instruc-tions and remove drawers from lateral.
Attach lateral file/door unit to top by inserting minifix bolts, attached to top, into holes drilled into top edge of lateral file/door unit.
Illustration 10
Threaded insertLeveling glide
Pedestal
Illustration 11
Minifix bolt
Shoulder
Dowel
Front edge of top
Illustration 12Lateral file/ door unit
Minifix bolt Front edge
of top
2420708800ESIDE
4 OF 9 (03/2018)
Illustration 13
Top
Minifix camArrow
Lateral file/ door unit~
~
3. Refer to Illustration 13. With arrows facing top, install six minifix cams (from hardware pack) into holes along top edge of each side of lateral file/door unit.
Use the Phillips screwdriver to tighten minifix cams. Turn minifix cams clockwise to tighten.
Illustration 144.
Refer to Illustration 14. Thread a glide (from hardware pack) into each glide insert (from hardware pack) by turning glide clockwise until glide is flat against insert.
Locate holes in bottom of lateral file/door unit. Install a glide/glide insert into each hole along bottom edge of lateral file/door unit. Use the rubber mallet to install a glide/glide insert assembly into hole.
Threaded insertLeveling glide
Lateral file/ door unit
Illustration 15
Minifix bolt
Shoulder
Dowel
Front edge of top
File Center to Top Assembly:1.
Refer to Illustration 15. Lay top, with holes up, on card
-
board or a carpeted surface.
At desired location, use the Phillips screwdriver to install six minifix bolts (from hardware pack) onto top as shown. Tighten each minifix bolt until minifix bolt shoulder is flat against surface of top.
Use the rubber mallet to install four dowels (from hard
-
ware pack) into large holes inline with minifix bolts.
File center
Minifix bolt Front edge
of top
2.
Refer to Illustration 16. Refer to drawer removal instruc
-
tions and remove drawers from file center.
Attach file center to top by inserting minifix bolts, attached to top, into holes drilled into top edge of file center.
Illustration 16
2420708800ESIDE
5 OF 9 (03/2018)
Illustration 17
Top
Minifix cam
Arrow
File center
~
~
3. Refer to Illustration 17. With arrows facing top, install six minifix cams (from hardware pack) into holes along top edge of each file center vertical panel.
Use the Phillips screwdriver to tighten minifix cams. Turn minifix cams clockwise to tighten.
4. Refer to Illustration 18. On top cross member, use the Phillips screwdriver to install four wood screws through holes in cross member and into top. Fully tighten screws.
Thread a glide (from hardware pack) into each glide insert (from hardware pack) by turning glide clockwise until glide is flat against insert.
Locate holes in bottom of file center. Install a glide/glide insert into each hole along bottom edge of file center. Use the rubber mallet to install a glide/glide insert assembly into hole.
Threaded insertLeveling glide
File center
Wood screwsCross member
Illustration 18
Illustration 20
Rafix boltEnd panel(s), pedestal(s), and/or storage unit(s) not shown for clarity.Shoulder
Front edge of top
Illustration 19
Minifix bolt
Shoulder
Dowel
Modesty panel
Modesty Panel to End Panel and Top Assembly:1. Refer to Illustration 19. Lay modesty panel, with holes
up, on cardboard or a carpeted surface.
On side being attached to end panel, use the Phillips screwdriver to install two minifix bolts (from hardware pack) onto modesty panel. Tighten each minifix bolt until minifix bolt shoulder is flat against surface of mod-esty panel.
Use the rubber mallet to install two dowels (from hard-ware pack) into large holes inline with minifix bolts.
2. Refer to Illustration 20. Lay top, with holes up, on card-board or a carpeted surface.
Use the Phillips screwdriver to install three rafix bolts (from hardware pack) onto top as shown. Tighten each rafix bolt until rafix bolt shoulder is flat against surface of top.
Refer to End Panel to Top Assembly instructions and attach end panel to top.
2420708800ESIDE
6 OF 9 (03/2018)
Illustration 21Modesty panel
Minifix bolt
Front edge of top
3.
Refer to Illustration 21. Once end panel is attached to top (refer to end panel to top assembly) attach modesty panel to end panel by inserting minifix bolts, attached to modesty panel, into holes drilled into rear edge of end panel.
4.
Refer to Illustration 22. With arrows facing modesty panel, install two minifix cams (from hardware pack) into holes along rear edge of each end panel. Use the Phillips screwdriver to tighten minifix cams. Turn minifix cams clockwise to tighten. Once modesty panel is attached to end panel, attach modesty panel to top. Use the Phillips screwdriver to tighten rafix cams. Turn rafix cams clockwise to tighten.
Modesty Panel to Pedestal and Top Assembly:1.
Refer to Illustration 23. Lay modesty panel, with holes up, on cardboard or a carpeted surface.
On side being attached to pedestal, use the Phillips screwdriver to install two minifix bolts (from hardware pack) onto modesty panel. Tighten each minifix bolt until minifix bolt shoulder is flat against surface of mod
-esty panel.
Use the rubber mallet to install two dowels (from hard
-
ware pack) into large holes inline with minifix bolts.
2. Refer to Illustration 24. Lay top, with holes up, on card-board or a carpeted surface.
Use the Phillips screwdriver to install three rafix bolts (from hardware pack) onto top as shown. Tighten each rafix bolt until rafix bolt shoulder is flat against surface of top.
Refer to Pedestal to Top Assembly instructions and attach end panel to top.
Modesty panel
Minifix camArrowEnd panel
Rafix cam
~
~
Minifix bolt
Shoulder
Dowel
Modesty panel
Rafix bolt
Shoulder
Front edge of top
Illustration 22
Illustration 23
Illustration 24
2420708800ESIDE
7 OF 9 (03/2018)
Illustration 25
Front edge of top
Minifix bolt
Pedestal
Modesty panel
3. Refer to Illustration 24. Once pedestal is attached to top (refer to pedestal to top assembly instructions) attach modesty panel to pedestal by inserting minifix bolts, attached to modesty panel, into holes drilled into rear edge of pedestal end panel.
Illustration 26
Modesty panel
Minifix camArrowPedestal end panel
Rafix cam
~
~
4. Refer to Illustration 26. With arrows facing modesty panel, install two minifix cams (from hardware pack) into holes along rear edge of pedestal end panel.
Use the Phillips screwdriver to tighten minifix cams. Turn minifix cams clockwise to tighten.
On opposite side of pedestal, use the Phillips screw-driver to install wood screws through holes in rear of pedestal and into modesty panel. Fully tighten screws.
Once modesty panel is attached to pedestal, attach modesty panel to top. Use the Phillips screwdriver to tighten rafix cams. Turn rafix cams clockwise to tighten.
Wood screws
Illustration 27
Minifix bolt
Shoulder
Dowel
Modesty panel
Modesty Panel to Lateral File/Door Unit/File Center and Top Assembly:1. Refer to Illustration 27. Lay modesty panel, with holes
up, on cardboard or a carpeted surface. On side being attached to lateral file/door unit/file
center, use the Phillips screwdriver to install two minifix bolts (from hardware pack) onto modesty panel. Tighten each minifix bolt until minifix bolt shoulder is flat against surface of modesty panel.
Use the rubber mallet to install two dowels (from hard-ware pack) into large holes inline with minifix bolts.
Illustration 28
Rafix bolt
Shoulder
Front edge of top
2.
Refer to Illustration 28. Lay top, with holes up, on card-board or a carpeted surface.
Use the Phillips screwdriver to install three rafix bolts (from hardware pack) onto top as shown. Tighten each rafix bolt until rafix bolt shoulder is flat against surface of top.
Refer to Lateral File/Door Unit/File Center Assembly instructions and attach lateral file/door unit/file center to top.
2420708800ESIDE
8 OF 9 (03/2018)
Illustration 293. Refer to Illustration 29. Once lateral file/door unit/file
center is attached to top (refer to lateral file/door unit/file center to top assembly instructions) attach modesty panel to lateral file/door unit/file center by inserting minifix bolts, attached to modesty panel, into holes drilled into rear edge of lateral file/door unit/file center end panel.
Illustration 304.
Refer to Illustration 30. With arrows facing modesty panel, install two minifix cams (from hardware pack) into holes along rear edge of lateral file/door unit/file center end panel.
Use the Phillips screwdriver to tighten minifix cams. Turn minifix cams clockwise to tighten.
On opposite side of lateral file/door unit/file center, use the Phillips screwdriver to install wood screws through holes in rear of lateral file/door unit/file center and into modesty panel. Fully tighten screws.
Once modesty panel is attached to lateral file/door unit/file center, attach modesty panel to top. Use the Phillips screwdriver to tighten rafix cams. Turn rafix cams clockwise to tighten.
Illustration 31
Modular Cabinet Assembly within Knee Space Area of Desk (refer to Illustrations 31 and 32):1. Once an end panel, or modular cabinet, and modesty
panel are attached to top at each end location (refer to the appropriate assembly instructions to install an end panel, pedestal, lateral file/door unit, or file center to top and attach modesty panel) attach desired cabinet to top at the desired location (refer to appropriate assembly instructions to attach cabinet to top).
2. Use the Phillips screwdriver to install wood screws through holes in rear of modular cabinet and into mod-esty panel. Fully tighten screws.
Front edge of top
Wood screwsPedestal, end panel, lateral file, door unit, or file center
Pedestal (installed in knee space loca-
Modesty panel
Illustration 32
Front edge of top
Minifix boltLateral file/ door unit/ file center end panel
Modesty panel
Modesty panel
Minifix camArrowLateral file/ door unit/ file center end panel
Rafix
~
~
Wood screws cam
Front edge of top
Wood screws
Lateral file/door unit/file center (installed in knee space location)
Modesty panel Pedestal, end panel, lateral file, door unit, or file center
Illustration 33 Pedestal Back to Single Pedestal Assembly:1. Refer to Illustration 33. Lay pedestal back, with holes
up, on cardboard or a carpeted surface. On side being attached to the pedestal, use the Phillips screwdriver to install two minifix bolts (from hardware pack) onto mod- esty panel. Tighten each minifix bolt until minifix bolt shoulder is flat against surface of pedestal back. Use the rubber mallet to install two dowels (from hardware pack) into large holes inline with minifix bolts.
2. Refer to illustration 34. Once pedestal is attached to top (refer to pedestal to top assembly) attach pedestal back by inserting minifix bolts, attached to pedestal back, into holes drilled into rear edges of the pedestal.
3. Refer to Illustation 35. With arrows facing pedestal back, install two minifix cams (from hardware pack) into holes along rear edge of each end panel. Use the Phillips screwdriver to tighten minifix cams. Turn mini-fix cams clockwise to tighten.
Pedestal back
Dowel
Minifix bolt
Illustration 34
Illustration 35
Pedestal back
Minifix cam
2420708800ESIDE
9 OF 9 (03/2018)