I.

J.

K.

O.

Wall Display Assembly Instructions

L.

N.

CONTENTS OF WOOD BOXA. Side Panels - qty 2B. Deck 3 pcs - qty1C1&2. Slatwall Bottom Panels (C2 has hole)- qty 2

E. Vertical Center Assembly Unit - qty 1F. 12" x 96" Black Litebox - qty 1G. 1.25" Drywall screws - qty 17H. 2" Drywall screws - qty 19I. 3" Drywall screws - qty 16J. Extension Cord - qty 1K. Snapframe Poster Holder - qty2L. Phillips Pan Head Machine Screws - qty 4M. Hex Nuts - qty 4N. Metal Slatwall Hooks - qty 12O. Cord Holders - qty 4P. Velcro - qty 16 piecesQ. Black Plastic Angle Molding - qty 2R. Grey Screw Cap Covers - qty 16S. Black Screw Cap Covers - qty 16

Tools necessary for assembly1. Electric drill with Phillips head2. Adjustable wrench or pliers3. One or two step ladders or stools

Due to the weight of the side panels and slatwall, it isrecommended that you take extreme CAUTION duringassembly. It is also recommended that at least 3 adultsassemble the unit.

T.H.

G.F.

E.

D1

C1

B.A.

NOTE: Thisdispl

ay will require free-standing wall space that is 96" wide x 96"high

.

NOTE: Wireless phones, posters, and other retail products are NOT included with thisp

romotional walldispl

ay.

P.

Q.

22"x 28"PosterHolder

T. Trapezoid Phone Holders - qty 8

C2

D2

D1&2. Slatwall Top Panels - qty 2

page 2 of 4

Tools necessary for assembly:1. Electric Drill with phillipshead2. 1 or 2 step ladders or stools3. Adjustable wrench or pliers4. 2- 3 adults

STEP 1.Back wall

Floor

STEP 2.Repeat onother side

STEP 3.Back of display

1. Place the 3 Deck pieces (B) on floor to assemble. Using 8 ofthe 2" drywall screws per side assemble the platform. Then placeapproximately 24" from the wall where it will ultimately rest. Thisunit must be positioned against the wall when completed.

2. Attach Side Panels (A) with 3" Drywall Screws (I) with electronicdrill. Insert and partially tighten all Drywall Screws (I), in rotationuntil Side Panels (A) are pulled snug. The side panels shouldstand on their own when completed.

3. Attach Slatwall Panel (C1) to back of display with finishedslatwall side facing outward. (See finished diagram.) Utilize 2"Drywall Screws (h) and insert into pre-drilled holes in edges ofSlatwall Panel. Line up to the edges of Side Panels (A) at top andbottom of slatwall, as screws are inserted, to create a flush finish.Back of the Side Panels (A) are not pre-drilled. Push SlatwallPanel (C1) tightly against Side Panels (A) while attaching.Eliminate any bowing in Slatwall Panel (C1) while attaching bypushing tightly against Side Panels (A). Lower edge of SlatwallPanel (C1) should rest on floor during assembly.Repeat step 3 with Slatwall Panel (C2) which has the large hole.

4. Repeat step 3 with Slatwall Top Panels (D1&2) This procedurewill require a minimum of 2 people. It is advised that 3 people areutilized as each Slatwall Panel weighs 40 pounds. Slatwall TopPanels (D1&2) should rest directly on top of Slatwall Panels(C1&2).

5. Attach Vertical Center Assembly (E) to front of display byaligning the light cord with the pre-cut hole in the Slatwall BottomPanel (D). This procedure will require 2 people. One person willhold the Vertical Center Assembly (E) in front of the display. Thesecond person will utilize the 1.25" Drywall Screws (G), from theback side, and insert the drywall screws through the pilot holesand into the Vertical Center Assembly (E). This procedure willutilize 17 drywall screws. The Vertical Center Assembly (E) doesnot have pre-drilled holes. Just hold the Vertical Center Assembly(E) tightly against the slatwall panels as the drywall screws (G)are inserted from the back side of the display.

6. Hang the 12" x 96" Black Litebox (F) on the front of the display.-This procedure requires 3 adults-Step ladders or stools-Electric drill or screw driver-Adjustable wrench or pliersUtilize the Phillips Pan Head Machine Screws (L) and Hex Nuts(M) to attach the 12" x 96" Black Litebox (F) to the top of the SidePanels (A). Two people should hold the Black Litebox (F) in place,on either end, by lining up the holes in the brackets mounted tothe back of the Black Litebox (F), with the holes in the top of theSide Panels (A). The brackets will rest against the inside of theSide Panels(A). Once this is done, the third person utilizing thePhillips Pan Head Machine Screws (L) and Hex Nuts (M), will slidetwo Phillips Pan Head Machine Screws (L) through each SidePanel (A), into the bracket and out the other side. Then securethem by threading on the Hex Nuts (M), Tighten down utilizing thepliers or wrench and electric drill. Repeat this process on the otherside of the display. When completing this step, it is important thetwo people holding the Black Litebox (F) quickly align the holes onboth ends so the third person can easily insert the Phillips PanHead Screws.

Use (8)2”drywallscrewsper side

page 3 of 4

STEP 4.Back of display

STEP 5.Front of display

Vertical CenterAssembly Unit

STEP 5.Back of display

Cord fromVerticalCenterAssemblyUnit

12" x 96"Litebox

STEP 6. This View:Looking up at bottom of 12" x 96" Liteboxand bracket assembly where they meetthe Side Panel

Bottom of Litebox F.

Outside edgeof Side Panel (A)

STEP 6.

STEP 6.Top Right cornerof Display

Bracket assembly(This piece is already attached to the back of the 12" x 96"Black Litebox (F))

LiteboxHolders

Assembler

11. Remove Trapezoid Phone Holders (T), Snapframe PosterHolders (K), Metal Slatwall hooks (N) from their respectiveboxes. Insert these items into the slatwall. Secure your actualphones to Phone Holders (T) by peeling back the adhesivebacking and attaching the small disc to the back of the phone.Wipe down Deck (B) of wall display and Side Panels with cleancloth. Apply Grey Screw Cap Covers (U) and Black Screw CapCovers (V) to respective exposed screw heads.

page 4 of 4Final Assembly

Back of Litebox F.

Top

Cord Holder Q.

or

STEP 10.Push from the bottom halfof the unit.

DO NOT PUSHUPPER EDGES

backwall

STEP 11.

STEP 9.

STEP 7.Please note there is only 1 cordcoming out of the 12" x 96" Black Litebox (F). The direction youwill guide the cord using the Cord Holders (O) will depend onthe location of the nearest outlet. Simply peel the tape onreverse side of the 12" x 96" Black Litebox (F) in thedesired direction. Continue this process up and onto the top of theSide Panel (A) toward the back sideof the Wall Display.

8. Align the 2 electrical cords from both sets of lighted signs atthe rear of the unit, depending on the location of the nearestoutlet. Utilize the Extension Cord (J) and plug into wall.

9. Attach the Black Plastic Angle Molding (Q) to the backcorners of the Wall display. Simply peel the double sided tapeand place the angle molding over the exposed edge of the Topand Bottom Slatwall Panels (C & D). The tape portion of theBlack Plastic Angle Molding (Q) should be applied to the backof unit.

10. Move the assembled Wall Display back against the wall.This will require 2 to 3 people. Push on the lower edges only ofthe side panels, alternating back and forth between the sides,until the entire display is near the wall. Do NOT push on theupper edges of the display as it could begin to fall over.

Optional Downlighting Kit (Sold Separately)

Down lighting is placed on top of wall unit with edges flush at every corner andlights facing downward into the wall unit. Four 1.25” drywall screws are provided forthe corners (screw holes are not pre-drilled). Make sure the power cord is placedbehind the wall unit

After assembly is completeCollect 12 metal reinforcement plates and 24 self taping screwsPosition plate over slat/cube wall joint as shown above.Drive screws through holes in metal plates into the slat/cube wall.Continue for the other 11, arrainging in the pattern shown above.