volvo penta genset enginetad1240ge - hodag volvo penta genset enginetad1240ge 1500 rpm, 340 kw (462...
TRANSCRIPT
The TAD1240GE is a powerful, reliable and economical Generating Set Diesel Engine built on the dependable in-line six design.
Durability & low noiseDesigned for easiest, fastest and most economical installation. Well-balanced to produce smooth and vibration-free opera-tion with low noise level. To maintain a controlled working tem-perature in cylinders and combustion chambers, the engine is equipped with piston cooling. The engine is also fitted with replaceable cylinder liners and valve seats/guides to ensure maximum durabil-ity and service life of the engine.
Low exhaust emissionThe state of the art, high-tech injection and charging system with low internal losses contributes to excellent combus-tion and low fuel consumption.The TAD1240GE complies with EU stage 2 and TA-Luft -50% exhaust emis-sion regulations.
Easy service & maintenanceEasily accessible service and mainte-nance points contribute to the ease of service of the engine.
Technical description:Engine and block– Optimized cast iron cylinder block with opti-
mum distribution of forces without the block being unnessarily heavy.
– Wet, replaceable cylinder liners– Piston cooling for low piston temperature
and reduced ring temperature– Tapered connecting rods for reduce risk of
piston cracking– Crankshaft induction hardened bearing
surfaces and fillets with seven bearings for moderate load on main and high-end bear-ings
– Case hardened and Nitrocarburized trans-mission gears for heavy duty operation
– Keystone top compression rings for long service life
– Viscous type crankshaft vibration dampers to withstand single bearing alternator tor-sional vibrations
– Replaceable valve guides and valve seats– Over head camshaft and four valves per cyl-
inder
Lubrication system– Full flow oil cooler– Full flow disposable spin-on oil filter, for ex-
tra high filtration– The lubricating oil level can be measured
during operation– Gear type lubricating oil pump, gear driven
by the transmission
Fuel system– Non-return fuel valve– Electronic Unit Injectors– Fuel prefilter with water separator and wa-
ter-in-fuel indicator / alarm– Gear driven low-pressure fuel pump– Fine fuel filter with manual feed pump and
fuel pressure switch– Fuel shut-off valve, electrically operated
Cooling system– Air to air intercooler– Gear driven, maintenance-free coolant
pump with high degree of efficiency– Coolant filter as standard
– Efficient cooling with accurate coolant con-trol through a water distribution duct in the cylinder block. Reliable sleeve thermostat with minimum pressure drop
Turbo charger– Efficient and reliable turbo charger– Extra oil filter for the turbo charger
Electrical system– Electronical Diesel Control III (EDCIII), an
electronically controlled processing system which optimizes engine performance. It also includes advanced facilities for diagnostics and fault tracing
– Three different ways for the customer to connect his controls and instrument to the engine. CAN SAE J1939 interface, CIU (Control interface unit) and Stand alone connections.
– Sensors for oil pressure, oil temp, boost pressure, boost temp, coolant temp, fuel temp, water in fuel, fuel pressure and two speed sensors.
Features– Maintained performance, air temp 40°C– Tropical cooling system (55°C)– Fully electronic with Volvo Penta EDC III– Dual frequency switch (between 1500 rpm and 1800 rpm)– High power density– Emission compliant– Low noise levels– Gen Pac configuration
VOLVO PENTA GENSET ENGINE
TAD1240GE1500 rpm, 340 kW (462 hp) – 1800 rpm, 346 kW (471 hp)
Power StandardsThe engine performance corresponds to ISO 3046, BS 5514 and DIN 6271. The technical data applies to an engine without cooling fan and operating on a fuel with calorific value of 42.7 MJ /kg (18360 BTU/lb) and a density of 0.84 kg/liter (7.01 lb/US gal), also where this involves a deviation from the standards. Power output guaranteed within 0 to +2% att rated ambient conditions at delivery. Ratings are based on ISO 8528. Engine speed governing in accordance with ISO 3046/IV, class A1 and ISO 8528-5 class G3Exhaust emissionsThe engine complies with EU stage 2 emission legislation according to the Non Road Directive EU 97/68/EEC. The engine also complies with TA-luft -50% exhaust emission regulations.
Rating GuidelinesPRIME POWER rating corresponds to ISO Standard Power for continuous operation. It is applicable for supplying electrical power at variable load for an unlimited number of hours instead of com-mercially purchased power. A10 % overload capability for govering purpose is available for this rating. MAXIMUM STANDBY POWER rating corresponds to ISO Standard Fuel Stop Power. It is applicable for supplying standby electrical power at variable load in areas with well established electrical networks in the event of normal utility power failure. No overload capability is available for this rating.1 hp = 1 kW x 1.36InformationFor more technical data and information, please look in the Gener-ating Set Engines Sales Guide.
TAD1240GE
AB Volvo PentaSE-405 08 Göteborg, Sweden
www.volvopenta.com
Technical DataGeneralEngine designation ........................................................................ TAD1240GENo. of cylinders and configuration ....................................................... in-line 6Method of operation ............................................................................... 4-strokeBore, mm (in.) ..................................................................................... 131 (5.16)Stroke, mm (in.) .................................................................................. 150 (5.91)Displacement, l (in³) .................................................................... 12.13 (740.2)Compression ratio ..................................................................................... 17.5:1Dry weight, kg (lb) .......................................................................... 1380 (3036)With Gen Pac, kg (lb) ................................................................... 1645 (3627)Wet weight, kg (lb) ........................................................................ 1455 (3201)With Gen Pac, kg (lb) ................................................................... 1720 (3792)
Performancewith fan, kW (hp) 1500 rpm 1800 rpmPrime Power 301 (409) 301 (409)Max Standby Power 331 (450) 331 (450)
Lubrication systemOil consumption, liter/h (US gal/h) 1500 rpm 1800 rpmPrime Power 0.11 (0.029) 0.12 (0.032)Max Standby Power 0.12 (0.032) 0.13 (0.034)Oil system capacity incl filters, liter ................................................................35
Fuel systemSpecific fuel consumption at Prime Power, g/kWh (lb/hph) 1500 rpm 1800 rpm25 % 222 (0.360) 242 (0.393)50 % 200 (0.324) 209 (0.339)75 % 196 (0.318) 201 (0.336) 100 % 197 (0.319) 201 (0.336)Max Standby Power, g/kWh (lb/hph) 1500 rpm 1800 rpm25 % 217 (0.352) 237 (0.384)50 % 199 (0.323) 206 (0.334)75 % 194 (0.314) 199 (0.323)100 % 197 (0.319) 202 (0.328)
Intake and exhaust systemAir consumption at 27°C, m³/min (cfm) 1500 rpm 1800 rpmPrime Power 22.4 (791) 26.7 (943)Max Standby Power 23.6 (833) 27.9 (985)Max allowable air intake restriction, kPa (In wc) ...............................5 (20.1)Heat rejection to exhaust,kW (BTU/min) 1500 rpm 1800 rpmPrime Power 245 (13933) 260 (14786) Max Standby Power 276 (15696) 289 (16435)Exhaust gas temperature after turbine, °C (°F) 1500 rpm 1800 rpmPrime Power 494 (921) 448 (838)Standby Power 517 (963) 474 (885)Max allowable back-pressure in exhaust line, kPa (In wc) ...........10 (40.2)Exhaust gas flow, m³/min (cfm) 1500 rpm 1800 rpmPrime power 59.9 (2115) 65.4 (2310)Max Standby Power 65.3 (2306) 70.5 (2490)
Cooling systemHeat rejection radiation from engine, kW (BTU/min) 1500 rpm 1800 rpm Prime Power 24 (1365) 12 (682)Max Standby Power 38 (2161) 26 (1479)Heat rejection to coolant,kW (BTU/min)Prime Power 130 (7393) 134 (7620)Max Standby Power 129 (7336) 134 (7620 )Fan power consumption, kW (hp) 9 (12) 15 (20)
Standard equipment E GPEngineAutomatic belt tensioner • •Lift eyelets • •FlywheelFlywheel housing with conn. acc. to SAE 1 • •Flywheel for 14” flex. plate and flexible coupling • •Vibration dampers • •Engine suspensionFixed front suspension • •Lubrication systemOil dipstick • •Full-flow oil filter of spin-on type • •By-pass oil filter of spin-on type • •Oil cooler, side mounted • •Low noise oil sump • •Fuel systemFuel filters of disposable type • •Electronic unit injectors • •Pre-filter with water separator • •Intake and exhaust systemAir filter without rain cover • •Air filter with replaceable paper insert • •Air restriction indicator • •Air cooled exhaust manifold • •Connecting flange for exhaust pipe • •Exhaust flange with v-clamp • •Turbo charger, low right side • •Crankcase ventilation • •Cooling systemTropical radiator incl intercooler •¹) •Gear driven coolant pump • •Fan hub • •Thrust fan – •Fan guard – •Belt guard – •Control systemEngine Management System (EMS) with • •CAN-bus interface SAE J1939 and stand aloneinterface AlternatorAlternator 60A / 24 V • •Starting systemStarter motor, 6.0kW, 24 V • •Connection facility for extra starter motor • •Instruments and sendersTemp.- and oil pressure for automatic • • stop/alarm 103°COther equipmentExpandable base frame – •Engine PackingPlastic warpping • •
1)must be ordered, se order specification - optional equipment− optional equipment or not applicable • included in standard specification
Note! Not all models, standard equipment and accessories are available in all countries. All specifications are subject to change without notice.The engine illustrated may not be entirely identical to production standard engines.
Eng
lish
10
-20
07
. ©
20
07
AB
Vol
vo P
enta
A* = 1587 mm / 62.5 in B* = 1120 mm / 44.1 in C* = 1976 mm / 77.8 inD = 2296 mm / 90.5 in (During transport)D = Max 3311 mm / 130.5 in*Incl. radiator and intercooler
Dimensions TAD1240GENot for installation
General
litrein3
mmin
mmin
r/min 1500 1800without fan kW 292 315
hp 397 428with fan kW 283 300
hp 385 408without fan kW
hpwith fan kW
hpwithout fan kW 320 345
hp 435 469with fan kW 311 330
hp 423 449Prime Power Nm 1859 1671
lbft 1371 1232Standby Power Nm 2037 1830
lbft 1502 1350m/s 7,5 9,0
ft/sec 24,7 29,6MPa 1,92 1,73psi 278 251
MPa 14,6 15,7psi 2117 2277
kgm2
lbft2
1:66 1:133 %kW 27 38
r/min 1500 1800dB(A) 105,4 106,5dB(A) 111 112,2dB(A) 111 112,2
No load dB(A) 92,8 94,2Prime Power dB(A) 98,5 99,6Standby Power dB(A) 98,4 99,5
In-line four stroke diesel engine with direct injection. Rotation direction, anti-clockwise viewed towards flywheel. Turbocharged
Calculated sound pressure Lp at 1 m
Degree of irregularity at Prime PowerResidual speed droop at load increase from 0 to 100%Friction Power
No loadPrime PowerStandby Power
Technical data TAD1240GE Prime & Standby Power
Bore
Stroke
1315,16150
Number of cylinders 612,13Displacement, total
740,21-5-3-6-2-4
Measured sound power Lw
Compression ratio
Continuous Standby Power:
Standby Power:
3,75
Mean piston speed
Effective mean pressure at Prime Power
Max combustion pressure at Prime Power
Total mass moment of inertia, J (mR2)
Firing order
18,5:15,91
PerformancePrime Power:
0-8
Torque at:
89,0
Engine noise emissionTest Standards: ISO 3744-1981 (E)sound power (without fan, intake and exhaust noise)Tolerans ± 0.75 dB(A)
Technical data TAD1240GE Prime & Standby Power
Unsilenced exhaust noise
r/min 1500 1800dB(A) 114 117dB(A) 114 118
Load acceptance
Remaining loadPrime Standby Prime Standby (%) Prime Standby Prime Standby
0-20 2,5 2,7 1,8 1,9 20-100 22,8 27,0 6,6 6,90-40 4,2 4,5 2,5 2,7 40-100 13,3 14,1 2,8 3,00-60 6,9 7,7 2,7 2,8 60-100 8,9 9,3 2,3 2,50-64 10,0 3,0 64-100 8,5 2,30-70 10,0 3,0 70-100 5,5 7,0 2,0 2,00-80 15,5 19,7 3,2 3,3 80-100 3,0 1,80-100 25,5 30,5 4,5 4,9100-0 7,6 7,8 3,3 3,5
Remaining loadPrime Standby Prime Standby (%) Prime Standby Prime Standby
0-20 1,7 1,8 1,8 1,9 20-100 11,2 12,5 3,4 3,50-40 2,0 2,1 2,1 2,1 40-100 7,4 7,8 2,9 3,10-60 3,2 3,6 2,5 2,6 60-100 5,6 5,9 2,7 4,00-80 6,3 7,6 2,7 2,8 80-100 1,6 1,7 2,1 2,20-86 10,0 3,0 86-100 0,8 1,70-94 10,0 3,0 94-100 0,8 1,50-100 10,3 10,8 3,0 3,0100-0 5,5 5,6 3,4 3,5
Cold start performance r/min 1500 180015 s 2,2 2,20 s 1,8 1,8
-15 s 7,2 7,2
15 s 4,2 4,5
0 s 4,1 4,3-15 s 14,5 14,8
Derating
r/min 1500 1800% 0 4% 10 18
% / °C%
Ambient temperature derating factorHumidity
Speed diff (%)
Single step load performance at 1800 rpmLoad (%) Speed diff % Recovery time (s) Speed diff (%) Recovery time (s)
Load (%)
Data calculated as sound pressure Lp.Assumed microphone distance 1 m
Speed diff (%)
Prime Power Standby Power
Test condition: Warm engine. Load acceptance performance can vary due to actual alternator inertia,voltage regulator, type of load and local ambient conditions.Single step load performance at 1500 rpm
Recovery time (s)Recovery time (s)
The engine will operate up to 2000 m altitude without derating. For operation at higher altitudes the power will be derated according to the following factors:
Without manifold heater engaged, lubrication oil 15W/40
Altitude derating factor at 2000 mAltitude derating factor at 5000 m
Time from start to stay within 0.8% of no load speed at ambient temperature:
°CTime from start to no load speed at ambient temperature:
°C
No deratingNo derating
Technical data TAD1240GE Prime & Standby Power
r/min 1500 1800liter/h 0,10 0,11
US gal/h 0,026 0,029liter/h 0,11 0,12
US gal/h 0,029 0,032liter
US galmax liter
US galmin liter
US gal
hhh
front up °front down °side tilt °
kPakPa
normal oC
max oCOil filter micron size mm
Fuel system r/min 1500 180025% g/kWh 222 242
lb/hph 0,360 0,39250% g/kWh 200 209
lb/hph 0,324 0,33975% g/kWh 197 200
lb/hph 0,319 0,324100% g/kWh 198 204
lb/hph 0,321 0,33125% g/kWh 218 242
lb/hph 0,353 0,39250% g/kWh 199 213
lb/hph 0,323 0,34575% g/kWh 196 200
lb/hph 0,318 0,324100% g/kWh 199 207
lb/hph 0,323 0,336
liter/h 110 120kPam
mm
°B.T.D.C - -°B.T.D.C - -
400
11
Lubrication oil temperature:
Engine angularity limits:
Prime Power
Standby Power
Lubricating oil consumptionLubrication system
ACEA E2, API CD, CF, CF-4, CG-4*
Oil sump capacity:
35
31
5,0
600Oil change intervals/specifications:
VDS-2*
9,2
198,2
0,040
2001111
400-550250
115
130
3502
0,005
ASTM-D975-No1 and 2-DJIS KK 2204, EN 590
Electronic / EDCIII-
Feed pump max suction headFuel filter micron sizeGovernor type/make, standardInjection pump type/makeInjection timing std.Injection timing
Recommended fuel to conform to
Total fuel flowFeed pump pressure
Oil system capacity including filters
Prime Power.Specific fuel consumption at:
Standby Power.Specific fuel consumption at:
* See also general section in the sales guide
VDS, ACEA, E3*
Oil pressure at rated speedOil pressure shut down switch setting
Technical data TAD1240GE Prime & Standby Power
Intake and exhaust system r/min 1500 1800at 27°C m3/min 21,4 26,9
cfm 756 950
at 27°C m3/min 23,2 28,7cfm 819 1014kPa 2 2
in wc 8,0 8,0kPa 5 5
in wc 20,1 20,1
%Prime Power kW 210 240
BTU/min 11942 13649Standby Power kW 235 270
BTU/min 13364 15355
Prime Power oC 480 440oF 896 824
Standby Power oC 485 465oF 905 869
kPa 10 10In wc 40,2 40,2
Prime Power m3/min 52,9 62,1cfm 1868 2193
Standby Power m3/min 57,8 68,8cfm 2041 2430
Heat rejection to exhaust at:
Exhaust gas temperature after turbine at:
Max allowable back pressure in exhaust line
Exhaust gas flow at:
Air filter type Single stage paper cartridgeAir filter cleaning efficiency 99,85
Air intake restriction, clean filter(s)
Max allowable air intake restriction
Standby Power
Air consumption at: Prime Power
Technical data TAD1240GE Prime & Standby PowerCooling system r/min 1500 1800
Prime Power kW 15 16BTU/min 853 910
Standby Power kW 16 17BTU/min 910 967
Prime Power kW 124 135BTU/min 7052 7677
Standby Power kW 133 148BTU/min 7564 8417
m²foot²mminm²
foot²mmin
mmin
kW 9 15hp 12 20
literUS gal
literUS gal
drive/ratiol/s 4,8 6
US gal/s 1,27 1,59l/s 4,6 5,7
US gal/s 1,22 1,51kPa 40 60
in wc 161 241start to open °C
°Ffully open °C
°FkPa
in wckPa
in wc°C°F°C°F°C°F
Recommended draw down capacity 10% of total cooling system capacity
Shutdown switch setting 103
Maximum top tank temperature 103
Minimum temperature entering engine 68
Maximum static pressure head 50
Pressure cap setting on standard radiator 70
Coolant flow with standard system
Minimum coolant flow
Maximum external coolant system restriction
82Thermostat,
engine
Coolant pump gear / 1.41:1
Volvo coolant or Volvo anticorrosion additive together with clean fresh water
Recommended coolant
Radiator cooling system type Closed circuitRadiator core area (std. size) 0,8
Radiator core thickness (std. size) 50
Heat rejection radiation from engine at:
Heat rejection to coolant at:
20
Intercooler core area (std. Size)
Intercooler core thickness (std. Size)
1,00:1
8,61
1,97
9,58
2,68
0,89
68
95
Fan diameter 890
std radiator with hoses 245,28
Coolant capacity,
35,04Fan power consumption
Fan drive ratio
217
217
154
6,34
203
201
281
180
Technical data TAD1240GE Prime & Standby Power
Cooling performance
1500 304050555962
1800 304050556062
r/min 1500 1800
make/output Amptacho output Hz/alt. Revdrive ratio
maketypekW
control current Amphold current Ampflywheelstarter motor
AmpAmprpm
max Ahmin at +5°C Ahpull current Amphold current Amp
kWAmp
r/min 1500 1800Nm
max left kW 30 50max down kW 19 31max right kW 30 50
Nm
Nm
Nm
< 2
4550
Alternator:
63,41:1
24V / insulated from earth
Starter motor solenoid,
-
Electrical system
Starter motor BoschGVB6,0
Voltage and typeValeo / 60
400Cranking current at +20°C
Number of teeth on: 15312
Inrush current at +20°C 1500-1650
Power relay for the manifold heater
Power take offFront end in line with crank shaft max: 600
Speed ratio direction of rotation viewed from flywheel side 1.65:1/anti-clockwise
Front end belt pulley load. Direction of load viewed from flywheel side:
Timing gear at compressor PTO max: 140Speed ratio direction of rotation viewed from flywheel side 1,31:1/anti-clockwiseTiming gear at servo pump PTO max: 40
--
Inlet manifold heater (at 20 V) 4,0
Stop solenoid,
Crank engine speed at 20°CStarter motor battery capacity: 2x143 570A DIN
2x88 400A DIN
200
8,457,85
141011257254952600
208016804,45
5,756,65
1120775
6,607,20
3,60
3,103,804,855,60
112077545508,45
141011257254952600
208016804,45
5,756,657,85
6,607,20
3,60
3,103,804,855,60
Cooling air flow and maximum additional external restriction at different radiator air temperatures based on 103°C TTT and 50% antifreeze (radiator and cooling fan, see optional equipment)Engine speedrpm
Air on temp°C
110% OF PRIME POWERMax additional external
restriction Pa
STANDBY POWERAir flow
m3/s
Air flow
m3/s
Max additional ext. restriction Pa
Speed ratio direction of rotation viewed from flywheel sideTiming gear at hydraulic pump PTO max: 400
0,97:1/anti-clockwise
1
Technical data TAD1240GE Prime & Standby Power
Sound power level1/3 octave band analysis
40
50
60
70
80
90
100
110
20 31,5 50 80 125 200 315 500 800 1,25 2k 3,15 5k 8 12,5 20kFrequency Hz
dB (A)
1500 rpm
1800 rpm
Fuel consumption
0,0
10,0
20,0
30,0
40,0
50,0
60,0
70,0
80,0
90,0
0 50 100 150 200 250 300 350 400
Power kW
Liter/h
1500 rpm
1800 rpm
Technical data TAD1240GE Prime & Standby Power
Smoke emission
0,0
0,5
1,0
1,5
2,0
2,5
0 50 100 150 200 250 300 350
Power (kW)
Bosch Units
1500 rpm
1800 rpm
1500 rpm
1800 rpm
Water pump capacity
0
50
100
150
200
250
0 1 2 3 4 5 6 7 8 9
Capacity (Liters/s)
Static pressurehead (kPa)
Pres. Dropover eng.1500 rpm
1800 rpm
Pres. Dropover eng.