viking mag drive internal gear and spur gear pumps datablader/viking/viking serie... · viking pump...

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2008

®

GPM .06 to 75③ (Nominal Rating)

Viking® Mag Drive is designed to provide positive- displacement pumping capability in those situations that require the highest assurance of liquid containment. Viking Mag Drive provides for the safe, trouble-free transfer of hazardous, EPA-regulated fluids without electronic monitoring as required with mechanical face-type shaft seals. Hard-to-seal liquids are also easily handled with the Viking Mag Drive which eliminates the high cost of mechanical seal replacement and repair. A variety of coupling sizes are available for flow requirements to 75 GPM. The torque-carrying ability of high-strength magnets allows pumps to be coupled with gear reducers for slow-speed handling of viscous liquids. The self-priming positive-displacement pumping principle provides low-shear, nonpulsating flow. Internal gear pumps are available in stainless steel, steel, and cast iron construction. External gear pumps are available in cast iron or ductile iron construction with heat- treated steel shafts and gears.① See following pages and performance curves for specific recommendations.

Certain models have lower limitations.② Optional samarium cobalt magnets are used at temperatures over 225°F.③ Nominal capacities based on handling thin liquids at low pressures.

Kalrez®- Registered trademark of DuPont Performance Elastomers.Viton®- Registered trademark of DuPont Performance Elastomers.Viking® and Viking Mag Drive®- Registered trademarks of Viking Pump, Inc.

① Differential Pressures

To 34 BARTo 500 PSI External Gear

To 8.5 BARTo 125 PSI Internal Gear

② Temperature Range

-50°C. to +260°C.-60°F. to +500°F.

① Viscosity Range

1.0 cSt. to 55,000 cSt.28 SSU to 250,000 SSU

FEATURES

INTERNAL GEAR AND SPUR GEAR PUMPSWITH MAGNETIC DRIVE

TemperatureSensor

CasingBushing

BalancePlate Casing

Head

Idler Pin

Head GasketOuter Magnet Assembly

Bearing Carrier Assembly Canister

Shaft

Bracket

Inner Magnet AssemblyCanister O-Ring

RotorIdler

Pressure Relief Valve

SERIES 897 PumpsCutaway View

“HL” size shown

INTERNAL GEARViking internal gear Mag Drive pumps are available in stainless steel, steel, or cast iron construction with capacities up to 75 GPM. With only two moving parts Viking Mag Drive and Viking’s gear-within-a-gear principle provides low-shear pumping.

MAGNETIC COUPLINGViking Mag Drive magnetically couples the pump to the driver. Magnetic force passing through a stainless steel canister is used to drive the inner coupling, eliminating the need for shaft seals.

EXTERNAL SPUR GEARViking external spur gear Mag Drive pumps are available in cast iron construction in capacities from .06 to 32 GPM. The Viking Mag Drive can be used in conjunction with a Viking Spur Gear Pump for metering or low-capacity transfer of toxic or expensive liquids.

Section 680Page 680.�Issue D


®

PumpConstruction ① O-Ring Casing Head Rotor Idler

BalancePlate

RotorShaft

IdlerPin

IdlerBushing

InternalPressure Relief

ValveStainless

Steel PTFE StainlessSteel

StainlessSteel

StainlessSteel ③ PPS PPS Coated

Stainless SteelCoated

Stainless SteelCarbonGraphite

StainlessSteel

Steel Buna-N Steel Steel ② DuctileIron ③ PPS PPS Steel Steel Carbon

GraphiteSteel

Externals

Cast Iron Buna-N Iron Iron ② DuctileIron ③ PPS PPS Steel Steel Carbon

Graphite Iron

CONSTRUCTION—SERIES 897 (STAINLESS STEEL)—SERIES 893 (STEEL) AND SERIES 895 (CAST IRON)

① Buna-N, Viton®, Neoprene, PTFE, or Kalrez® O-Rings available.② Standard construction includes iron rotor for “GG” and “HJ” sizes: ductile iron rotor for

“HL” through “AL” sizes. When steel-fitted construction is required, hardened steel rotor will be provided on “GG” through “HJ” sizes.

③ Standard Material is Polyphenylene Sulfide with composite material. Recommend using metal idler above 10,000 SSU.

④ See pages 680.21 through 680.44 for specific coupling recommendation on other pressures and viscosities. See page 20 for “Selecting the correct Mag Drive coupling.”

⑤ Higher temperatures can be handled with Samarium Cobalt magnets. See page 20 for torque and temperature limits.

⑥ “AS” and “AK” Series 895 have 2½” NPT tapped ports.⑦ For bearing carrier weights add 8 lbs (2 KG) for “MD-A” size, add 17 lbs (4 KG) for “MD-B” size.

ModelNumbers

Materialsof

Construction

PortSize

NominalPumpRating

④MagneticCoupling

Availability⑤MaximumTemperature

(Standard Construction)

MaximumHydrostatic

Pressure

ApproximatePump Shipping

WeightWith Valve

(Less Power)

⑦ Approximate Coupling Only

Shipping Weight (ready to accept but less power)

Series

Torque

Inches GPM m³/h RPM Ft-Lbs NmDegrees

F.Degrees

C. PSIG bar Lbs. KG Lbs. KGGG-897 Stainless Steel

110 2.3 1800

MD-A4

9

5.4

12.2225 93 400 28 22 10

31 14

GG-893 Steel7 1.6 1200GG-895 Cast Iron

HJ-897 Stainless Steel

1½20 4.5 1800

MD-A

MD-B

4

9

15

40

5.4

12.2

20.3

54

225 93 400 28 30 14HJ-893 Steel13 3.0 1200HJ-895 Cast Iron

HL-897 Stainless Steel

1½30 6.8 1800

225 93 400 28 30 14

71 32

HL-893 Steel20 4.5 1200HL-895 Cast Iron

AS-897 Stainless Steel⑥ 3 35 8.0 1200

MD-B

MD-C

15

40

80

20.3

54

108

225 93 400 28 78 35AS-893 SteelAS-895 Cast IronAK-897 Stainless Steel

⑥ 3 50 11 1200 225 93 400 28 78 35AK-893 SteelAK-895 Cast IronAL-897 Stainless Steel

3 75 17 1200 225 93 400 28 78 35 95 43AL-893 SteelAL-895 Cast Iron

SPECIFICATIONS — SERIES 897, 893 AND 895

Dimensions for Internal Gear Mag Drive Pumps - See Pages 680.4 through 680.12.Performance Data for Internal Gear Mag Drive Pumps - See Pages 680.21 through 680.44.

SERIES 895 PumpsMD-B15M, motor direct connected to bracket and pump with tapped ports.

SERIES 895 PumpsMD-B15B, bearing carrier,

footed bracket, andmounted pump with

tapped ports.

SERIES 897, 893 AND 895INTERNAL GEARSTAINLESS STEEL, STEEL AND CAST IRON WITH MAGNETIC DRIVE

Section 680Page 680.�Issue E


®

① Buna-N, Viton®, Neoprene, PTFE, or Kalrez® O-Rings available.② Standard construction includes iron rotor for “GG” and “HJ” sizes: ductile iron rotor for

“HL” through “AL” sizes. When steel-fitted construction is required, hardened steel rotor will be provided on “GG” through “HJ” sizes.

③ Standard Material is Polyphenylene Sulfide with composite material. Recommend using metal idler above 10,000 SSU.

④ See pages 680.21 through 680.44 for specific coupling recommendation on other pressures and viscosities. See page 20 for “Selecting the correct Mag Drive coupling.”

⑤ Higher temperatures can be handled with Samarium Cobalt magnets. See page 20 for torque and temperature limits.

⑥ “AS” and “AK” Series 895 have 2½” NPT tapped ports.⑦ For bearing carrier weights add 8 lbs (2 KG) for “MD-A” size, add 17 lbs (4 KG) for “MD-B” size.

① Viton®, Neoprene, PTFE, or Kalrez® available.② See page 20 for “Selecting the correct Mag Drive coupling.”

③ Higher temperatures can be handled with Samarium Cobalt magnets. See page 20 for torque and temperature limits.

ModelNumbers

PortSize

(NPT)

NominalPumpRating

② MagneticCoupling

Availability③ MaximumTemperature

(StandardConstruction)

MaximumHydrostatic

Pressure

ApproximateShipping Weight

With Valve(Less Power)

Approximate Coupling Only

Shipping Weight (ready to accept but

less power)

Series

Torque

Inches GPM m³/h RPM Ft-Lbs NmDegrees

F.Degrees

C. PSIG bar Lbs KG Lbs KGSG-80417 ⅜ 0.06 0.013 1800

MD-A

4

9

5.4

12.2 225 107

1000 69

6 2.7

31 14

SG-80418 ⅜ 0.14 0.031 1800SG-80425 ⅜ 0.18 0.041 1800SG-80435 ⅜ 0.27 0.061 1800SG-80450 ⅜ 0.36 0.082 1800

7 3.2SG-80470 ⅜ 0.50 0.11 1800SG-80518 SGN-80518 ½ 0.70 0.16 1800

6 2.7SG-80525 SGN-80525 ½ 1.0 0.23 1800SG-80535 SGN-80535 ½ 1.4 0.32 1800SG-80550 SGN-80550 ½ 2.0 0.45 1800

7 3.2SG-80570 SGN-80570 ½ 2.8 0.63 1800SG-80510 SGN-80510 ½ 4.0 0.91 1800 8 3.6SG-80514 SGN-80514 ¾ 5.6 1.27 1800 9 4.1SG-80519 SGN-80519 ¾ 7.6 1.72 1800 10 4.5SG-80528 SGN-80528 ¾ 11.2 2.54 1800 11 5.0SG-80741 SGN-80741 1 4.0 0.91 1800

MD-A

MD-B

4

9

15

40

5.4

12.2

20.3

54.0

1000

400

69

28

15 6.8SG 80758 SGN 80758 1 5.6 1.27 1800 17 7.7SG-80782 SGN-80782 1 8.0 1.81 1800 18 8.2SG-80711 SGN-80711 1 11.2 2.54 1800 19 8.6SG-80716 SGN-80716 1 16.0 3.63 1800 20 9.1

71 32SG-80722 SGN-80722 1½ x 1¼ 22.0 5.00 1800 41 18.6SG-80732 SGN-80732 1½ x 1¼ 32.0 7.27 1800 43 19.5

SPECIFICATIONS — SERIES SG-804, SG-805, SG-807—CAST IRON - SGN-805, SGN-807—DUCTILE IRON

STAINLESS STEEL, STEEL AND CAST IRON WITH MAGNETIC DRIVE

CONSTRUCTION

Model Head, Casing, Separation

Plate & BracketGears

Heat-TreatedShafts

Case-HardenedBearings ①

O-RingsStandard OptionsSG-804, SG-805,

SG-807 Iron Steel Steel Carbon Graphite Needle Bearingsor Bronze Buna-N

SGN-805, SGN-807 Ductile Iron Steel Steel Carbon Graphite Needle Bearings or Bronze Buna-N

SERIES 804, 805, AND 807EXTERNAL SPUR GEARCAST IRON WITH MAGNETIC DRIVE

Dimensions for External Gear Mag Drive Pumps - See Pages 680.13 through 680.19.Performance Data for External Gear Mag Drive Pumps - See Pages 341.21 through 341.66.

SERIES SG-805 PumpsWith MD-A Mag Drive Coupling.

Section 680Page 680.3Issue F


Section 680Page 680.4Issue C

®

SERIES 893 AND 895STEEL AND CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.

For specifications, see page 680.2.

DIMENSIONS–SERIES 893STEEL UNMOUNTED PUMPS“GG”–“HJ”–“HL” SIZES


DIMENSIONS–SERIES 895CAST IRON UNMOUNTED PUMPS“GG”–“HJ”–“HL” SIZES

MODEL NO.(in)A B C E G H

GG-893 1in 4.00 4.29 1.12 0.62 0.50

mm 102 108 29 16 13

HJ-893HL-893 1½

in 4.00 5.44 1.50 0.62 0.50mm 102 138 38 16 13


GG-895 1in 2.75 4.29 1.12 0.62 0.50

mm 70 108 29 16 13

HJ-895HL-895 1½

in 3.75 5.44 1.50 0.62 0.50mm 95 138 38 16 13



®

SERIES 897 AND 895STAINLESS STEEL AND CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.

DIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.


GG-897 1in 4.00 4.29 1.12 0.62 0.50

mm 102 108 29 16 13

HJ-897HL-897 1½

in 4.00 5.44 1.50 0.62 0.50mm 102 138 38 16 13


DIMENSIONS–SERIES 897STAINLESS STEEL UNMOUNTED PUMPS“GG”–“HJ”–“HL” SIZES

MODEL NO.(in)A B C E G H J K

GG-895-MD-A_B 1in 2.75 4.29 1.12 0.62 0.50 4.35 15.30

mm 70 108 29 16 13 123 389

HJ-895-MD-A_B HL-895-MD-A_B 1½

in 3.75 5.44 1.50 0.62 0.50 5.50 16.75mm 95 138 38 16 13 140 425


DIMENSIONS–SERIES 895(MD-A–“B” DRIVE)“GG”–“HJ”–“HL” SIZES

① Series 895 shown. See unmounted pump for port configuration on Series 893 and 897 pumps.


Section 68080.6Issue C

®

SERIES 895CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.


DIMENSIONS–SERIES 895(MD-B–“B” DRIVE)“HJ”–“HL” SIZES


MODEL NO.(in)A B C D E G H J K L M N P R T W

GG-895-MD-A_M 1in 2.75 4.29 3.50 1.12 0.62 0.50 4.85 4.75 3.50 0.62 0.50 6.72 2.75 5.25 0.34

mm 70 108 89 29 16 13 123 121 89 16 16 171 70 133 9

HJ-895-MD-A_MHL-895-MD-A_M

1½in 3.75 5.44 3.50 1.50 0.62 0.50 5.50 4.75 3.50 0.62 0.50 6.72 2.75 5.25 0.34

mm 95 138 159 38 16 13 140 121 89 16 13 171 70 133 9

HJ-895-MD-B_MHL-895-MD-B_M

1½in 3.75 5.44 6.25 1.50 0.62 0.75 6.63 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56

mm 95 138 159 38 16 13 164 165 127 19 13 178 70 210 14


DIMENSIONS–SERIES 895(MD-A AND MD-B–“M” DRIVE)“GG”–“HJ”–“HL” SIZES




®


SERIES 893 AND 895STEEL AND CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.


DIMENSIONS–SERIES 893STEEL UNMOUNTEDPUMPS“AS”–“AK”–“AL” SIZES


DIMENSIONS–SERIES 895CAST IRON UNMOUNTED PUMPS“AS”–“AK”–“AL” SIZES

MODEL NO.(in)A B C E F G H

AS-893AK-893 3

in 6.00 7.50 2.00 7.00 1.12 0.75mm 152 190 51 178 29 19

AL-893 3in 6.00 7.25 2.50 7.00 1.12 0.75

mm 152 184 63 178 29 19


AS-895AK-895 2½

in 5.00 7.50 2.00 7.00 1.12 0.75mm 127 190 51 178 29 19

AL-895 3in 5.00 7.25 2.50 7.00 1.12 0.75

mm 127 184 63 178 29 19



®

SERIES 897 AND 895STAINLESS STEEL AND CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.


DIMENSIONS–SERIES 897STAINLESS STEEL UNMOUNTED PUMPS“AS”–“AK”–“AL” SIZES


AS-897AK-897 3

in 6.00 7.50 2.00 7.00 1.12 0.75mm 152 190 51 178 29 19

AL-897 3in 6.00 7.25 2.50 7.00 1.12 0.75

mm 152 184 63 178 29 19


DIMENSIONS–SERIES 895(MD-B– “B” DRIVE)“AS”–“AK”–“AL” SIZES


MODEL NO.(in)A B C E F G H J K

AS-895-MD-B_BAK-895-MD-B_B 2½

in 5.00 7.50 2.00 7.00 1.12 0.75 8.69 23.53mm 127 190 51 178 29 19 221 598

AL-895-MD-B_B 3in 5.00 7.25 2.50 7.00 1.12 0.75 8.44 23.78

mm 127 184 63 178 29 19 14 604



®

MODEL NO.(in)A B C D E F G H J K L M N P R T W

AS-895-MD-B_M AK-895-MD-B_M 2½

in 5.00 7.50 6.25 2.00 7.00 1.12 0.75 8.69 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56mm 127 190 159 51 178 29 19 221 165 127 19 13 178 70 214 14

AL-895-MD-B_M 3in 5.00 7.25 6.25 2.50 7.00 1.12 0.75 8.44 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56

mm 127 184 159 63 178 29 19 214 165 127 19 13 178 70 214 14

SERIES 895CAST IRON CONSTRUCTIONPERFORMANCE CURVE NOTES


DIMENSIONS–SERIES 895(MD-C80 “B” DRIVE)“AS”–“AK”–“AL” SIZES



DIMENSIONS–SERIES 895(MD-B–“M” DRIVE)“AS”–“AK”–“AL” SIZES


MODEL NO.(in)A B C E F G H J K

AS-895-MD-C80-BAK-895-MD-C80-B 2½

in 5.00 7.50 2.00 7.00 1.12 0.75 8.25 22.83mm 127 190 51 178 29 19 210 580

AL-895-MD-C80-B 3in 5.00 7.25 2.50 7.00 1.12 0.75 8.00 23.08

mm 127 184 63 178 29 19 203 586


Section 680Page 680.�0Issue C

®


MODEL NO.(in)A B C L M

GG-895-MD-A_R 1in 2.75 8.12 3.73 4.29

mm 70 206 95 108

HJ-895-MD-A_RHL-895-MD-A_R 1½

in 3.75 8.12 4.88 5.44mm 95 206 124 138

HJ-895-MD-B_RHL-895-MD-B_R 1½

in 3.75 10.87 6.00 5.44mm 95 276 152 138


DIMENSIONS–SERIES 895(MD-A– AND MD-B–“R” DRIVE)“GG”–“HJ”–“HL” SIZES“A” SIZE REDUCER UNITS



Section 680Page 680.��Issue C

®



DIMENSIONS–SERIES 895(MD-B–“R” DRIVE)“AS”–“AK”–“AL” SIZES“A” SIZE REDUCER UNITS



DIMENSIONS–SERIES 895(MD-B–“R” DRIVE)“AS”–“AK”–“AL” SIZES“B” SIZE REDUCER UNITS



Section 680Page 680.��Issue C

®


DIMENSIONS–SERIES 895(MD-C80 “R” DRIVE)“AS”–“AK”–“AL” SIZES“B” SIZE REDUCER UNITS



DIMENSIONS–SERIES 895(MD-C80 “D” DRIVE)“AS”–“AK”–“AL” SIZES


SERIES 895CAST IRON CONSTRUCTIONPERFORMANCE CURVE NOTES



®

PERFORMANCE CURVE NOTES

SERIES SG-804 AND SG-805CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.


DIMENSIONS–SERIES SG-804, SG-805 AND SGN-805(MD-A–“B” DRIVE)

MODEL NO.(in)A

WITH R/V LESS R/V

DDB C E B C E

SG-80417MD-A_B ⅜in 2.02 13.71 2.08 2.21 12.71 2.27 0.31

mm 51 348 53 56 323 58 8

SG-80418MD-A_B ⅜in 2.02 13.71 2.08 2.21 12.71 2.27 0.31

mm 51 348 53 56 323 58 8

SG-80425MD-A_B ⅜in 2.09 13.78 2.15 2.28 12.78 2.34 0.31

mm 53 350 55 58 325 59 8

SG-80435MD-A_B ⅜in 2.19 13.88 2.25 2.38 12.88 2.44 0.31

mm 56 352 57 60 327 62 8

SG-80450MD-A_B ⅜in 2.34 14.03 2.40 2.53 13.03 2.59 0.31

mm 59 356 61 64 331 66 8

SG-80470MD-A_B ⅜in 2.54 14.23 2.60 2.73 13.23 2.79 0.31

mm 65 361 66 69 336 71 8

SG-80518MD-A_B SGN-80518MD-A_B ½

in 2.02 13.71 2.08 2.21 12.71 2.27 0.31

mm 51 348 53 56 323 58 8


in 2.09 13.78 2.15 2.28 12.78 2.34 0.31

mm 53 350 55 58 325 59 8


in 2.19 13.88 2.25 2.38 12.88 2.44 0.31

mm 56 352 57 60 327 62 8

SG-80550MD-A_BSGN-80550MD-A_B ½

in 2.34 14.03 2.40 2.53 13.03 2.59 0.31

mm 59 356 61 64 331 66 8


in 2.54 14.23 2.60 2.73 13.23 2.79 0.31

mm 65 361 66 69 336 71 8


in 1.84 14.53 1.90 1.84 13.53 1.90 0.31

mm 47 369 48 47 344 48 8

SG-80514MD-A_B SGN-80514MD-A_B ¾

in 2.04 14.93 2.10 2.04 13.93 2.10 0.19

mm 52 379 53 52 354 53 5


in 2.29 15.43 2.35 2.29 14.43 2.35 0.19

mm 58 392 60 58 367 60 5


in 2.04 16.33 2.10 2.04 15.33 2.10 0.19

mm 52 415 53 52 389 53 5



®

SERIES SG-807CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.

MODEL NO.

(in) WITH R/V LESS R/V

A B C E B C E

SG-80741MD-A_B SGN-80741MD-A_B 1

in 3.07 15.81 3.13 3.26 14.19 3.32

mm 78 402 80 83 360 84


in 3.24 15.98 3.30 3.43 14.36 3.49

mm 82 406 84 87 365 89


in 3.48 16.22 3.54 3.67 14.60 3.73

mm 88 412 90 93 371 95


in 3.81 16.55 3.87 4.00 14.93 4.06

mm 97 420 98 102 379 103


in 4.31 17.05 4.37 4.50 15.43 4.56

mm 109 433 111 114 392 116

SG-80722MD-A_B SGN-80722MD-A_B

1½S1¼D

in 4.25 20.20 4.31 4.44 18.58 4.50

mm 108 513 109 113 472 114

SG-80732MD-A_B SGN-80732MD-A_B

1½S1¼D

in 4.75 21.20 4.81 4.94 19.58 4.62

mm 121 538 122 125 497 117

S = Suction PortD = Discharge Port


DIMENSIONS–SERIES SG-807 AND SGN-807(MD-A–“B” DRIVE)



®



SERIES SG-807CAST IRON CONSTRUCTION

MODEL NO.

(in) WITH R/V LESS R/V

A B C E B C E

SG-80741MD-B_B SGN-80741MD-B_B 1

in 3.07 15.81 3.13 3.26 14.19 3.32

mm 78 402 80 83 360 84


in 3.24 15.98 3.30 3.43 14.36 3.49

mm 82 406 84 87 365 89


in 3.48 16.22 3.54 3.67 14.60 3.73

mm 88 412 90 93 371 95


in 3.81 16.55 3.87 4.00 14.93 4.06

mm 97 420 98 102 379 103


in 4.31 17.05 4.37 4.50 15.43 4.56

mm 109 433 111 114 392 116

SG-80722MD-B_B SGN-80722MD-B_B

1½S1¼D

in 3.78 20.20 4.31 4.44 18.58 4.50

mm 108 513 109 113 472 114

SG-80732MD-B_B SGN-80732MD-B_B

1½S1¼D

in 4.75 21.20 4.81 4.94 19.58 4.62

mm 121 538 122 125 497 117



DIMENSIONS–SERIES SG-807 AND SGN-807(MD-B–“B” DRIVE)



®


DIMENSIONS–SERIES SG-804, SG-805 AND SGN-805(MD-A–“M” DRIVE)


SERIES SG-804 AND SG-805CAST IRON CONSTRUCTION

MODEL NO.(in)A

WITH R/V LESS R/VDD

MOTOR FRAME

SIZE D E F H MCB C B C

SG-80417MD-A_M ⅜ in 2.02 9.15 2.21 8.15 0.31

56C3.50 2.44 1.50 0.34

SLOT 2.56mm 51 232 56 207 8

SG-80418MD-A_M ⅜ in 2.02 9.15 2.21 8.15 0.3189 62 38 9 65mm 51 232 56 207 8

SG-80425MD-A_M ⅜ in 2.09 9.22 2.28 8.22 0.31mm 53 234 58 209 8

143TC3.50 2.75 2.00 0.34 2.88

SG-80435MD-A_M ⅜ in 2.19 9.32 2.38 8.32 0.31mm 56 237 60 211 8

89 70 51 9 73SG-80450MD-A_M ⅜ in 2.34 9.47 2.53 8.47 0.31mm 59 241 60 215 8

SG-80470MD-A_M ⅜ in 2.54 9.67 2.73 8.67 0.31

145TC3.50 2.75 2.50 0.34 2.88mm 65 246 69 220 8

SG-80518MD-A_M SGN-80518MD-A_M ½ in 2.02 9.15 2.21 8.15 0.31

89 70 64 9 73mm 51 232 56 207 8SG-80525MD-A_M

SGN-80525MD-A_M ½ in 2.09 9.22 2.28 8.22 0.31mm 53 234 58 209 8

182TC4.50 3.75 2.25 0.41 3.62SG-80535MD-A_M

SGN-80535MD-A_M ½ in 2.19 9.32 2.38 8.32 0.31mm 56 237 60 211 8

114 95 57 10 92SG-80550MD-A_M SGN-80550MD-A_M ½ in 2.34 9.47 2.53 8.47 0.31

mm 59 241 64 215 8SG-80570MD-A_M

SGN-80570MD-A_M ½ in 2.54 9.67 2.73 8.67 0.31

184TC4.50 3.75 2.75 0.41 3.62mm 65 246 69 220 8

SG-80510MD-A_M SGN-80510MD-A_M ½ in 1.84 9.97 1.84 8.97 0.31

114 95 70 10 92mm 47 253 47 228 8SG-80514MD-A_M

SGN-80514MD-A_M ¾ in 2.04 10.37 2.04 9.37 0.19mm 52 263 52 238 5

213TC*5.25 4.25 2.75 0.41 4.5SG-80519MD-A_M

SGN-80519MD-A_M ¾ in 2.29 10.87 2.29 9.87 0.19mm 58 276 58 251 5

133 108 70 10 114SG-80528MD-A_M SGN-80528MD-A_M ¾ in 2.04 11.77 2.04 10.77 0.19

mm 52 299 52 274 5 * Motor shaft must be modified to resemble 182TC-184TC shaft length, diameter and key.



®




MODEL NO.(in)A

WITH R/V LESS R/V MOTOR FRAME

SIZE D E F H MCB C B CSG-80741MD-A_M

SGN-80741MD-A_M 1 in 3.07 11.25 3.26 9.6356C

3.50 2.44 1.50 0.34 SLOT 2.56mm 78 286 83 245 89 62 38 9 65

SG-80758MD-A_M SGN-80758MD-A_M 1 in 3.24 11.42 3.43 9.80

143TC3.50 2.75 2.00 0.34 2.88

mm 82 290 87 24989 70 51 9 73SG-80782MD-A_M

SGN-80782MD-A_M 1 in 3.48 11.66 3.67 10.04145TC

3.50 2.75 2.50 0.34 2.88mm 88 296 93 25589 70 64 9 73SG-80711MD-A_M

SGN-80711MD-A_M 1 in 3.81 11.99 4.00 10.37mm 97 305 102 263

182TC4.50 3.75 2.25 0.41 3.62

SG-80716MD-A_M SGN-80716MD-A_M 1 in 4.31 12.49 4.50 10.87 114 95 57 10 92

mm 109 317 114 276184TC

4.50 3.75 2.75 0.41 3.62SG-80722MD-A_M

SGN-80722MD-A_M1½S 1¼D

in 4.25 15.64 4.25 15.02114 85 70 10 92mm 108 397 108 356

213TC*5.25 4.25 2.75 0.41 4.50SG-80732MD-A_M

SGN-80732MD-A_M1½S 1¼D

in 4.75 16.64 4.75 15.02133 108 70 10 114mm 121 423 121 382

* Motor shaft must be modified to resemble 182TC-184TC shaft length, diameter and key.


DIMENSIONS–SERIES SG-807 AND SGN-807(MD-A–“M” DRIVE)


®

SERIES SG-807CAST IRON CONSTRUCTIONDIMENSIONSThese dimensions are average and not for construction purposes. Certified prints on request.

MODEL NO.(in)A

WITH R/V LESS R/VB C E B C E

SG-80741MD-A_M SGN-80741MD-A_M 1

in 3.07 11.25 3.13 3.26 9.63 3.32mm 78 286 80 83 245 84


in 3.24 11.42 3.30 3.43 9.80 3.49mm 82 290 84 87 249 89


in 3.48 11.66 3.54 3.67 10.04 3.73mm 88 269 90 93 255 95


in 3.81 11.99 3.87 4.00 10.37 4.06mm 97 305 98 102 263 103


in 4.31 12.49 4.37 4.50 10.87 4.56mm 109 317 111 114 276 116

SG-80722MD-A_M SGN-80722MD-A_M

1½S1¼D

in 4.25 15.64 4.31 4.25 14.02 4.31mm 108 397 109 108 356 109

SG-80732MD-A_M SGN-80732MD-A_M

1½S1¼D

in 4.75 16.64 4.81 4.75 15.02 4.81mm 121 423 122 121 382 122



DIMENSIONS–SERIES SG-807 AND SGN-807MD-A–“M” DRIVE(FOOTED BRACKET)

Footed bracket is only available for up to 145TC frame motors (4.5” rabbet) - 180TC and 210TC motor frames with 8.5” rabbet are only available with footless bracket, see page 680.17

Section 680Page 680.�8Issue D


®




MODEL NO.(in)A

WITH R/V LESS R/VB C E B C E

SG-80741MD-B_M SGN-80741MD-B_M 1

in 2.60 13.97 3.79 2.80 12.35 3.98mm 66 355 96 71 314 101


in 2.77 14.14 3.96 2.97 12.52 4.15mm 70 359 101 75 318 105


in 3.01 14.38 4.20 3.21 12.76 4.39mm 76 365 107 82 324 112


in 3.34 14.17 4.53 3.54 13.09 4.72mm 85 374 115 90 332 120


in 3.84 15.20 5.03 4.04 13.59 5.22mm 98 386 128 103 345 133

SG-80722MD-B_M SGN-80722MD-B_M

1½S1¼D

in 3.78 18.35 4.97 3.78 16.73 4.97mm 96 466 126 96 425 126

SG-80732MD-B_M SGN-80732MD-B_M

1½S1¼D

in 4.28 19.35 5.47 4.28 17.73 5.47mm 109 491 139 109 450 139

S = Suction Port D = Discharge Port


DIMENSIONS–SERIES SG-807 AND SGN-807MD-B–“M” DRIVE

Coupling will accept motor frames 182TC-256TC. 254TC-256TC will require shaft modification reducing shaft extension by ⅝”.

Section 680Page 680.�8.�Issue C

viking mag drive internal gear and spur gear pumps datablader/viking/viking serie... · viking pump...

Documents