view product
TRANSCRIPT
Wideband PowerAmplifier APTHPA-00700270-xx50
Engineering: +1 (646) 416-2052 / [email protected] Specifications may change without noticeFacility U.S.: +1 (631) 521-7831 / [email protected] 2 / 5 Version 1.1
Absolute Maximum Ratings
PARAMETER UNIT RATING
Input RF Power dBm 0
Supply Voltage V 35
Load Mismatch Value - 3 : 1 @all load phase
* Input Signal Condition : CW 1-Tone
Environmental Characteristics
PARAMETER UNIT MIN TYP MAX SYMBOL
Operating Flange Temperature °C -10 - 70 Tc
Storage Temperature °C -40 - 105 Tstg
Vibration MIL-STD-810G Method 514.6 ANNEX C VI
Mechanical Specifications
PARAMETER UNIT TYP Dimension ㎜ 134(L) x 105(W) x 30(H)
Weight g 635
RF Connector - RF Input : SMA Female
RF Output : N-Type Female
DC Connector - C7W2 / D-SUB / Male type
Cooling - External Heat-sink
Wideband PowerAmplifier APTHPA-00700270-xx50
Engineering: +1 (646) 416-2052 / [email protected] Specifications may change without noticeFacility U.S.: +1 (631) 521-7831 / [email protected] 3 / 5 Version 1.1
Typical Performance @ 25°C
Frequency Pout @Pin -3dBm
Gp @Pin -3dBm
Current @Pin -3dBm
PAE @ Pin -3dBm
Harmonic 2nd Harm 3rd Harm
(MHz) (dBm) (dB) (A) (%) (dBc) (dBm)
700 50.47 53.47 10.47 33.26 -12.26 -31.88 800 49.45 52.45 9.04 30.46 -15.66 -24.97 900 51.07 54.07 9.80 40.80 -22.20 -24.46
1000 50.18 53.18 8.92 36.52 -16.51 -40.08 1100 50.87 53.87 8.41 45.40 -21.79 -38.36 1200 50.33 53.33 6.98 48.31 -19.76 -33.86 1300 49.42 52.42 5.85 46.74 -18.99 -18.83 1400 50.01 53.01 8.07 38.81 -28.13 -30.48 1500 50.00 53.00 8.41 37.16 -34.43 -40.04 1600 49.78 52.78 8.30 35.79 -34.02 -54.08 1700 49.66 52.66 8.64 33.45 -43.59 -56.70 1800 49.88 52.88 9.43 32.24 -35.86 -64.36 1900 50.07 53.07 9.89 32.11 -21.00 -58.44 2000 50.29 53.29 9.53 35.06 -21.04 -45.14 2100 50.04 53.04 9.20 34.28 -41.85 -49.81 2200 49.81 52.81 8.68 34.46 -47.34 -61.68 2300 49.45 52.45 8.24 33.41 -42.68 -59.77 2400 49.21 52.21 7.74 33.66 -62.21 -63.68 2500 49.26 52.26 7.97 33.07 -51.35 -69.88 2600 50.03 53.03 8.44 37.28 -57.91 -46.57 2700 49.22 52.22 7.75 33.69 -61.61 -55.20
Precautions
1. This product is designed to be used for broadband amplification. Heat generation is higher when there is RF signal in the device. Therefore, the worst case scenario is when there is RF signal. The temperature must be calculated properly. Case temperature must maintain below 70°C.
2. Thermal Grease or Metal Thermal Interface Materials are recommended for heat dissipation. An example would be spreading thermal grease on the bottom of the device.
Wideband PowerAmplifier APTHPA-00700270-xx50
Specifications may change without noticeFacility U.S.: +1 (631) 521-7831 / [email protected] 4 / 5 Version 1.1
Package Dimensions
* Unit: mm[inch] | Tolerance: ±0.2[.008]
Pin Description ( C7W2 / D-SUB / Male type ) Pin No Description I/O Specifications
A1 Vcc I +32VDC
A2 GND I Ground
1 GND I Ground
2 Shut Down I Enable : TTL “Low”, Disable : TTL “High”
(Low : 0 ~ 0.5V, High : 2.5 ~ 5V) Disable Status : 150mA Current consumption
3 GND I Ground
4 Temperature Monitor O Reference voltage : 750mV @ 25℃, Scale : 10mV/℃
5 Power Monitor O Pout 48dBm Voltage : 700 ~ 1000mV, Scale : 25mV/dB * Recommended Screw Torque : 8.0kgf.cm±1 using SEMS M3 19mm Bolt
Wideband PowerAmplifier APTHPA-00700270-xx50
Engineering: +1 (646) 416-2052 / [email protected] Specifications may change without noticeFacility U.S.: +1 (631) 521-7831 / [email protected] 5 / 5 Version 1.1
Revision History
Part Number Release Date Version Modification Data Sheet Status
HPA-00700270-xx50 2014.4.2 1.0 Initial Release -
HPA-00700270-xx50 2014.5.23 1.1 Mechanical Specifications -
HPA-00700270-xx50
AmpliTech Inc. reserves the right to make changes to any products herein or to discontinue any product at any time without notice. While product specifications have been thoroughly examined for reliability, Amplitech Inc. strongly recommends buyers to verify that the information they are using is accurate before ordering. AmpliTech Inc. does not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. AmpliTech products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. If Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold AmpliTech and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such unauthorized use. Sales, inquiries and support should be directed to the local authorized geographic distributor for AmpliTech Inc. For customers in the US, please contact the US Sales Team at +1 (631)521-7831. For Engineering inquiries, please contact Stan Starinski at +1 (646) 416-2052.