Panel Connectors

VideoEdge Hybrid Appliance 16 Channel Analog

Standard Items

Whats in the Box 1

Results

Analog Camera

VGA or Flat Panel Monitor (not shown) PC with Internet Browser and Network Connection (not shown)

Required Accessories (not in this box)

IP Encoder Gigabit Switch

2

5

Quick Setup Guide

8200-1024-03 A0 2013 Tyco Security Products. All rights reserved.

VideoEdge Hybrid Appliance 2U Server

Note: The VideoEdge software is installed on the server, the VideoEdge Software Recovery USB should be kept in a safe place. The serial number printed on the label is your proof of license to use the software this will be required if you need to recover your system .

Supported IP Cameras (not shown) and/or IP Encoders Analog Cameras

3

Localized Power Cord

The VideoEdge Hybrid Appliance should be powered up and running. The VideoEdge web page should be displayed on the client PC.

Is the Unit Functioning as Described?

NO!

If you have checked all these items and the unit fails to power up, or you repowered your unit and the unit still fails to operate properly, please contact your American Dynamics Representative.

YES!

The VideoEdge Hybrid Appliance is ready to be licensed and configured.

Is the VideoEdge Hybrid Appliance powered up?Check the power connections.

Did you see the boot sequence on the VGA/DVI-I monitor?If not, power the VideoEdge Hybrid Appliance off and restart. You may need to re-install the NVR Software.

Can you connect with a browser?If not, verify the IP address is correct by using the ping command from a Command Prompt window. Verify the network connections, IP addresses and subnet masks on the client. The default IP addresses is 10.10.10.10.

Connect Power and additional cables as indicated:

It is highly recommended to use an Uninterruptible Power Supply (UPS)

Always follow appropriate safety precautions

Unit powers up when you press the Power button on the front panel

Be sure to use surge protection for power supply and provide appropriate grounding

VGA Monitor and peripherals should be powered up before the unit is powered up

(Optional) Connect PTZ cables to serial connectors for PTZ controls

Connect DVI-I to blue female connector, HDMI and Display ports to their corresponding connectors.

Connect Monitor via DVI-I, HDMI or Display Port

Connect Analog Cameras (Up to 16)

Connect Power Cord

Connect BNC Monitor Out #1

Keyboard

For more information on the supported IP Encoders and IP Cameras visit:http://www.americandynamics.net/Products/VideoEdge_NVR.aspx then select the Supported Devices tab.

4 Power Up and Test

The unit will power up as soon as you press the Power button on the front of the unit.

VideoEdge Software Recovery USB

Note: Microsoft Internet Explorer versions 8 or 9 are the only supported browsers for ac-cessing the Appliance web interface.

Enter the default Username admin and default Password VIDEO!edge23

Note: The VideoEdge Hybrid Appliance is supplied with a temporary 60 day licence. To register for your full licence you are required to configure your NVR to the configura-tion you wish to use then Generate a Host ID, see User Manual for further information.

To apply for your licence use the VideoEdge Licensing Activation Icon to be directed to the American Dynamics website or enter the address in your browser

Mouse

For detailed information please refer to the VideoEdge Hybrid Appliance Installation and User Manual

For further Troubleshooting please refer to the VideoEdge Hybrid Appliance Installation and User Manual.

Connect LAN 1 Cable to RJ45 Connector

Use proper network switch and cable

Note: For reliable time based playback both the VideoEdge Hybrid Appliance and Client PC need to be configured as clients.

Gigabit Ethernet switches and cabling

Connect BNC Monitor Out #2

Connect LAN 2 Cable to RJ45 Connector

Use proper network switch and cable

Note - To access the Power Button you must remove the bezel

A series of boot messages appear and the system loads to the OS log in page.

Default Factory Settings

Network Settings: Eth0 has a default IP address of 10.10.10.10, Eth1 has a static IP ad-dress. Storage Settings: One media partition is configured on each connected hard drive. Media Folders are Enabled for storage. Appliance OS Credentials (For local access to the device OS): default Username - root and default Password - nvr Appliance Web Interface (For remote access and configuration): default Username - admin and default Password - VIDEO!edge23

Log on to the Appliance web interface on remote client.

Enter the default IP address into the address bar of your web browser.

I/O Terminal Connectors

Reset Pin

Rack Mounting Kit