video cassette recorder ownerõs guide · pdf filevideo cassette recorder ownerõs...

VIDEO CASSETTE RECORDEROWNER’S GUIDE

MODEL HS-U449

VCRPOWER

EJECT

CM SKIP

QUICK PROGRAM

INPUT

PLAY

STOP

PAUSE

INDEX

ADJUST

AUDIO/VIDEO

MENU

ADJUST

CANCELENTER

SP/EP

VCR/TV

DISPLAY

REW

REC

X2

FF

MUTE

TVPOWER

CHANNEL VOLUME

21

3

54

6

87

9

0

VCRTV

This Video Cassette Recorder is based on the VHS format. Only video cassette tapes with the

mark may be used with this model.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alertthe user to the presence of uninsulated “dangerous voltage” within the product’s enclosurethat may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to thepresence of important operating and maintenance (servicing) instructions in the literatureaccompanying the product.

IMPORTANT:RECORDING OF COPYRIGHTED TELEVISION PROGRAMS MAY VIOLATE COPYRIGHT LAW.

WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAINOR MOISTURE.

CAUTION:TO PREVENT ELECTRIC SHOCK HAZARD, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTEN-SION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTEDTO PREVENT BLADE EXPOSURE.

NOTE TO CATV SYSTEM INSTALLER:THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO SECTION820-40 OF THE NEC WHICH PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR,SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THEBUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

EASY:♦ViewPoint® Menu

Operating System♦OTR2 Advanced One

Touch Recording withdelayed start time

♦Auto Clock Set♦Front A/V input jacks

SMART:

♦Program ConflictWarning

♦VHS Hi-Fi audio record/playback

Special Features HS-U449

FAST:

♦Alfa 500 Precision HighSpeed Mechanism withfor 500x rewind/fastforward speed

♦Rental XpressTM – Autorewind, eject and poweroff for a fast moviereturn

1

To connect your VCR, go to page 4.

To play a tape, go to page 9.

To record a program, go to page 18.

To learn about Advanced Features, go to page 32.

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

IMPORTANT SAFEGUARDS................. 2

Hooking Up Your VCR ........................... 4

Playback................................................. 9

Setting Up Your VCR ............................. 12

Selecting the On-screen Language .... 12

Memorizing Channels Automatically ... 13

Adding and Deleting Channels ........... 14

Setting the Clock ................................ 15

Recording ............................................... 18

Recording a Current Broadcast .......... 18

OTR .................................................... 19

OTR2 ................................................... 20

Using Audio and Video Functions....... 21

Timer Recording ..................................... 24

Conventional VCR Timer Recording... 24

Quick Program.................................... 26

Timer Recording Hints ........................ 27

Editing Features ..................................... 30

Using Two VCRs to Copy ................... 30

Advanced Features ................................ 32

Advanced Playback Controls .............. 32

Searching Techniques ........................ 34

Displaying Time Gauge, Remaining Time,

Current Time ................................. 38

Customize Choices Menu................... 39

Advanced Options .............................. 42

Location of Controls ............................... 44

Important Information ............................. 47

Trouble Checks ...................................... 48

Specifications ......................................... 50

Index ...................................................... 50

Warranty ................................................. 53

TABLE OF CONTENTS

SHORTCUTS

2

Please read all these instructions carefully regarding your VCR before you begin operating it.Follow all warnings and instructions marked on the VCR. Thank you.

1 Read InstructionsAll the safety and operating in-structions should be read beforethe product is operated.

2 Retain InstructionsThe safety and operating instruc-tions should be retained for fu-ture reference.

3 Heed WarningsAll warnings on the product andin the operating instructionsshould be adhered to.

4 Follow InstructionsAll operating and use instruc-tions should be followed.

5 CleaningUnplug this product from the walloutlet before cleaning. Do notuse liquid cleaners or aerosolcleaners. Use a damp cloth forcleaning.

6 AttachmentsDo not use attachments not rec-ommended by the productmanufacturer as they may causehazards.

7 Water and MoistureDo not use this product near wa-ter — for example, near a bathtub, wash bowl, kitchen sink,laundry tub, in a wet basement,or near a swimming pool, and thelike.

8 AccessoriesDo not place this product on anunstable cart, stand, tripod,bracket, or table. The productmay fall, causing serious injuryto a child or adult, and seriousdamage to the product. Use onlywith a cart, stand, tripod, bracket,or table recommended by themanufacturer, or sold with theproduct. Any mounting of theproduct should follow themanufacturer’s instructions, andshould use a mounting acces-sory recommended by themanufacturer.

9 A product and cart combinationshould be moved with care.Quick stops, excessive force,and uneven sur-faces may causethe product andcart combinationto overturn.

10 VentilationSlots and openings in the cabi-net are provided for ventilationand to ensure reliable operationof the product and to protect itfrom overheating, and theseopenings must not be blocked orcovered. The openings shouldnever be blocked by placing theproduct on a bed, sofa, rug, orother similar surface. This prod-uct should not be placed in abuilt-in installation such as abookcase or rack unless properventilation is provided or themanufacturer’s instructions havebeen adhered to.

11 Power SourcesThis product should be operatedonly from the type of powersource indicated on the markinglabel. If you are not sure of thetype of power supply to yourhome, consult your productdealer or local power company.For products intended to oper-ate from battery power, or othersources, refer to the operating in-structions.

12 Grounding or PolarizationThis product is equipped with apolarized alternating-current lineplug (a plug having one bladewider than the other). This plugwill fit into the power outlet onlyone way. This is a safety fea-ture. If you are unable to insertthe plug fully into the outlet, tryreversing the plug. If the plugshould still fail to fit, contact yourelectrician to replace your obso-lete outlet. Do not defeat thesafety purpose of the polarizedplug.

13 Power-Cord ProtectionPower-supply cords should berouted so that they are not likelyto be walked on or pinched byitems placed upon or againstthem, paying particular attentionto cords at plugs, conveniencereceptacles, and the point wherethey exit from the product.

14 Outdoor Antenna GroundingIf an outside antenna or cablesystem is connected to the prod-uct, be sure the antenna or cablesystem is grounded so as to pro-vide some protection againstvoltage surges and built-up staticcharges.

Article 810 of the NationalElectrical Code, ANSI/NFPA 70,provides information with regardto proper grounding of the mastand supporting structure, ground-ing of the lead-in wire to an an-tenna discharge unit, size ofgrounding conductors, location ofantenna-discharge unit, connec-tion to grounding electrodes, andrequirements for the groundingelectrode.

15 LightningFor added protection for thisproduct during a lightning storm,or when it is left unattended andunused for long periods of time,unplug it from the wall outlet anddisconnect the antenna or cablesystem. This will prevent dam-age to the product due to light-ning and power-line surges.

16 Power LinesAn outside antenna system

ANTENNALEAD IN WIRE

ANTENNADISCHARGE UNIT(NEC SECTION 810-20)

GROUNDINGCONDUCTORS(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250, PART H)

GROUND CLAMP

ELECTRICSERVICEEQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING

IMPORTANT SAFEGUARDS

3

should not be located in the vi-cinity of overhead power lines orother electric light or power cir-cuits, or where it can fall into suchpower lines or circuits. When in-stalling an outside antenna sys-tem, extreme care should betaken to keep from touching suchpower lines or circuits as contactwith them might be fatal.

17 OverloadingDo not overload wall outlets, ex-tension cords, or integral conve-nience receptacles as this canresult in fire risk or electric shock.

18 Object and Liquid EntryNever push objects of any kindinto this product through open-ings as they may touch danger-ous voltage points or short-outparts that could result in a fire orelectric shock. Never spill liquidof any kind on the product.

19 ServicingDo not attempt to service this prod-uct yourself as opening or remov-ing covers may expose you to dan-gerous voltage or other hazards.Refer all servicing to qualified ser-vice personnel.

20 Damage Requiring ServiceUnplug this product from the walloutlet and refer servicing to quali-fied service personnel under thefollowing conditions:(a) When the power-supply cord

or plug is damaged.(b) If liquid has been spilled, or

objects have fallen into theproduct.

(c) If the product has been ex-posed to rain or water.

(d) If the product does not oper-ate normally by following theoperating instructions. Adjustonly those controls that arecovered by the operating in-structions as an improper ad-justment of other controlsmay result in damage and willoften require extensive workby a qualified technician to re-store the product to its nor-mal operation.

(e) If the product has beendropped or damaged in anyway.

(f) When the product exhibits adistinct change in perfor-mance – this indicates aneed for service.

21 Replacement PartsWhen replacement parts are re-quired, be sure the service tech-nician has used replacementparts specified by the manufac-turer or have the same charac-teristics as the original part. Un-authorized substitutions may re-sult in fire, electric shock or otherhazards.

22 Safety CheckUpon completion of any serviceor repairs to this product, ask theservice technician to performsafety checks to determine thatthe product is in proper operat-ing condition.

23 HeatThe product should be situatedaway from heat sources such asradiators, heat registers, stoves,or other products (including am-plifiers) that produce heat.

CONDENSATIONLeave the VCR on, without a tape init, for 2 hours if the VCR has beenexposed to sudden changes in tem-perature. Sudden temperaturechanges cause moisture to form onthe metal parts inside the VCR. Thismoisture can cause the tape to stickand damage the head. Leaving theVCR on for a 2 hour period will drythe inside of the VCR.

PROTECT THE POWER CORDDo not damage the power cord.Damage to the power cord maycause a fire or shock hazard. Whenunplugging the power cord, pleasehold it by the plug and remove itcarefully.

DO NOT PLACE HEAVYOBJECTS ON THE RECORDERHeavy objects placed on the re-corder will cause damage.

WHEN NOT IN USEWhen you finish operating the re-corder, always unload the cassetteand turn OFF the VCR POWER.

CARE OF THE VIDEOCASSETTE TAPES• Avoid violent vibration or shock.• Do not place in a location where

strong magnetic fields exist (neara motor, transformer or magnet).

• Never place or store in direct sun-light.

• Avoid dusty places.• Place the cassette in the cassette

case and store vertically.• Never store tape in a high humid-

ity location.

INFORMATIONThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in a particular instal-lation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, try to correct the interference by one or more of thesemeasures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a different circuit than the receiver is connected• Consult the dealer or an experienced radio/TV technician for helpChanges or modifications not expressly approved by the party responsible for compliance could void theuser’s authority to operate the equipment. If necessary, consult the dealer or an experienced radio/TVtechnician for additional suggestions. You may find this booklet prepared by the Federal CommunicationsCommission helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is availablefrom the US Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

4

Unpacking Your VCRAs you unpack your new VCR, please make sure the following items are included:

IMPORTANTNever place any heavy objects on top of the VCR. Do not placethe VCR on top of the television as the surface may not be stable.

Choosing a HookupThe connections shown in this book are general. Individual televisions and stereo systems can vary fromthose shown here. The first diagrams show connections for common equipment. Then, if you areconnecting equipment such as a Home Theater receiver, you will also use those diagrams after you haveconnected the common equipment.

IMPORTANTTo maximize your system for its best performance, your dealercan help you customize these hookups and sell you anyadditional connection accessories that may be necessary tomatch your particular equipment and antennas.

1 Make a list of each piece of equipment that you want to hook up.

2 If you are connecting several pieces of equipment, you may be using more than one of these diagrams.Using your list, find EACH of the diagrams you will need to connect all of your equipment. Forexample, to hook up this VCR, a TV, a cable box, and a Home Theater receiver, you will use CableSystem with Cable Box, and Connecting a Home Theater receiver.

3 If your TV has audio and video inputs, use the diagrams on page 7 in addition to the connections onpage 5 or 6.

21 3

54 6

87 9

0

• Remote control • 2 "AA" size batteries

• Registration card

• 1 Coaxial cable

Hooking Up Your VCR

5

Cable System withCable BoxConnecting Cable and Cable Box,if all channels are scrambled

1 Connect cable from wall outlet to CABLEIN on the cable box.

2 Connect OUT (or OUT TO TV) on thecable box to ANTENNA IN on the VCR.

3 Connect ANTENNA OUT on the VCR tothe TV’s antenna jacks (varies by TV).

4 If your TV has audio video inputs,continue with the connections on page 7.If not, plug in power cords of VCR, TV,and cable box.

If your cable company scrambles all of itschannels, you cannot record one channelwhile watching another.

If your cable company only requires the useof a cable box for some channels, connectthe cable box as shown on the next page.

VHF

UHF

VHF/UHF

ANTENNA

OUT

IN

x x

x x

VCR Rear Panel

TV Rear Panel

OR

OptionalUHF/VHF Splitter

Optional 300 Ohm to 75 OhmMatching Transformer

Optional UHF/VHF Combiner

OR

supplied coaxial cable

OR

From Antenna or Cable wall outlet

INOUT

VHF/UHF

VHF

UHF

ANTENNA

OUT

IN

TV Rear Panel

From Cable wall outlet

Cable Box Rear Panel

coaxial cable provided by cable company


VCR Rear Panel

OR

IMPORTANTYou must use one of the connections shown on page 5 and 6 in order to record television or cableprograms.

Antenna or CableSystem withoutCable BoxConnecting Antenna or Cable

1 Connect antenna or cable from walloutlet to ANTENNA IN of the VCR.

2 Connect VCR ANTENNA OUT tothe TV’s Antenna jacks (varies byTV).

3 If your TV has audio video inputs,continue with the connections onpage 7. If not, plug in power cordsof VCR and TV.

Hooking Up Your VCR

IMPORTANTYour TV Owner’s Guide may have additional suggestions for antenna/cable hookups.If your TV has more than one antenna jack, ask your Mitsubishi dealer for advice on additionalaccessories.

6

Hooking Up Your VCR

Connecting Cable and Cable Box, if only some channels are scrambled

VHF/UHF

VHF

UHF

ANTENNA

OUT

IN

TV Rear Panel

VCR Rear Panel

OR

From Cable wall outletCable box

SplitterA/B Switch

OUT IN

A

B

IN

OUTOUT


1 You will need a cable splitter, five lengths ofcoaxial cable, and a cable A/B switch.

2 Connect cable from wall outlet to IN terminalon the cable splitter.

3 Connect the coaxial cable to OUT terminal onthe cable splitter and A-IN on the A/B switch.

4 Connect the second coaxial cable to theother OUT terminal on the splitter and IN (orCABLE) on the cable box.

5 Connect the third coaxial cable to the OUTor TV on the cable box and B-IN on the A/Bswitch.

6 Connect the fourth coaxial cable to OUTterminal on the A/B switch and ANTENNAIN on the VCR.

7 Connect the fifth coaxial cable to theANTENNA OUT on the VCR to the TV’sANTENNA jacks (varied by TV).

8 If your TV has audio and video inputs,continue with the connections on the nextpage. If not, plug in power cords of VCR,TV, and cable box.

This connection will allow you to watch one non-scrambled channel while you record anothernon-scrambled channel.

With this connection, you should set the A/Bswitch to A to record a non-scrambled channel.You may watch the same channel or any othernon-scrambled channel at the same time.

To record a scrambled channel, set the switch toB, select your cable output channel (usually 3 or4) on the VCR and select the channel you wishto record on the cable box. At this time your TVwill not be able to show any other channel.

IMPORTANTWith this connection, you cannot:• record a scrambled channel and watch

a non-scrambled channel at the sametime.

• record a non-scrambled channel andwatch a scrambled channel at the sametime.

• record one scrambled channel andwatch a different scrambled channel.

7

IMPORTANT

You may need to purchase an audio/video cable for this hookup.

Your TV Owner’s Guide may haveadditional suggestions for audio/videohookups.

To connect your VCR to a mono (non-stereo) TV, connect only the whiteAUDIO OUT L of the VCR and the whiteAUDIO INPUT of the TV. Since the TVis not stereo, you cannot take advantageof your VCR’s Hi-Fi stereo sound.

If you have an older TV without audiovideo inputs, simply connect only theantenna or cable as shown on page 5 or6.

Connections to TV with Audio Video Inputs

INPUT-1

INPUT-2

OUTPUTMONITOR/TUNER

S-VIDEO VIDEO L (MONO) RAUDIO

OUTAUDIO

L

R

VIDEO

OUT

L

R

LR

R

White RedYellow

White

Red

Yellow

TV Rear Panel

VCR Rear Panel

Because you purchased a Hi-Fi VCR, you willwant to take advantage of its superior soundcapability and connect it to a stereo TV systemwith audio and video inputs. This connectionalso helps maintain the best picture quality.

1 Connect the red and white audio cable toAUDIO OUT R (right) and AUDIO OUT L(left) on the VCR. Connect the other end tothe TV’s AUDIO INPUT RIGHT and AUDIOINPUT LEFT. Match the colors of theconnectors to the cables.

2 Connect the yellow video cable to VIDEOOUT on VCR. Connect the other end toVIDEO INPUT on the TV.

3 Set the RF Converter to OFF. See page 40for instructions on this setting, which can bedone at a later time.

Hooking Up Your VCR

8

2 Connect a yellow video cable to VIDEO OUTon the VCR. Connect the other end to theVCR 1 VIDEO INPUT on the Home TheaterReceiver.

3 Connect a yellow video cable to theMONITOR OUT of the Home TheaterReceiver. Connect the other end to theVIDEO INPUT on the back of the TV.

4 See your Home Theater Receiver Owner’sGuide for information concerning audioconnection between TV and Home TheaterReceiver, or additional hookups andoperations.

IMPORTANTYou may need to purchase two sets ofaudio/video cables for this hookup.

Connections to Home Theater Receiver

INPUT 1

S-VIDEO VIDEO L (MONO) RAUDIO

R

VCR 1 VCR 2 TV

AUDIO

OUT IN OUT IN IN

VCR2 MONITORVCR 1

OUT IN OUT IN OUT

VIDEO

L

R

L

R

OUTAUDIO

L

R

VIDEO

OUT

R

L

LR

Yellow

YellowYellow

Yellow

TV Rear Panel

VCR Rear Panel

Home Theater Receiver Rear Panel

White

Red

White

Red

You may wish to connect your VCR to a HomeTheater Receiver so that you can takeadvantage of the Surround Sound audiorecordings that are common with many movies.Home Theater Receivers often will control boththe sound that is heard from the speakers andthe picture shown on your TV. Below is thebasic connection between your VCR and HomeTheater Receiver. If you use this connection,you will not use Connections to TV with AudioVideo Inputs.

1 Connect the red and white audio cables toAUDIO OUT R and AUDIO OUT L on theVCR. Connect the other end to the VCR 1AUDIO INPUT R and AUDIO INPUT L onthe Home Theater Receiver.

Hooking Up Your VCR

9

Setting Up Your VCRThe first thing you need to do is set up your VCR so that you cansee the picture coming from the VCR. It’s important to take a fewminutes to set up your VCR correctly before you try to use it.Based on the type of TV that you have, choose one of the following:

TV with Audio/Video Inputs1 Turn on your TV and switch it to the correct external input.

For most Mitsubishi TVs, this means pressing the TV’s INPUTbutton until you see the words Ext-1 or Input-1 on the screen.If you do not have a Mitsubishi TV, please refer to your TVOwner’s Guide for this procedure.

2 Turn the VCR on by pressing POWER.

3 You are now watching the VCR’s picture. To go back toviewing the picture from the TV, press the TV’s INPUT buttonto go back to the previous ANTENNA input position.

4 Later, you should turn the RF converter OFF by followinginstructions on page 40.

If your system includes a home theater receiver or an A/Vreceiver, refer to your home theater receiver’s owner’s guide.

TV without Audio/Video InputsIf your TV does not have separate audio/video inputs, then yourVCR will need to convert the VCR’s picture to channel 3 or 4.This is called the video channel. The factory has already selectedchannel 3; however, if it is a broadcast channel in your area, thenyou will need to change this to channel 4. To make this change:

set up1 To choose channel 4: with the VCR power OFF, press

CHANNEL ª and REC SPEED on the front panel at thesame time. CH4 will display on the front panel and the VCRwill send signals on channel 4.If needed, to return to channel 3: with the VCR turned OFF,press CHANNEL º and REC SPEED on the front panel atthe same time. CH3 will display.

2 Turn the VCR on by pressing POWER.operating3 Check to see if the VCR light on the front panel display is lit. If

it is not, press VCR/TV on the remote control until the VCR lightappears on the front panel. This light must be on when youwatch a video tape or use the VCR menus. The VCR light willturn on automatically when you play a tape or use the VCRmenus when the RF converter is set to ON. See page 40.

4 Turn on the TV and change the TV to the video channel (3 or4). You are now watching the VCR’s picture.

To watch a channel that is different than the channel your VCR isrecording, the VCR light must be off. The VCR/TV button turnsthis light on and off.

Playback

21 3

54 6

87 9

0

VCR/TV

POWERCHANNEL

REC SPEEDSP/EP

10

Operating Your Remote ControlInstalling the Batteries1 To remove the back cover, press the ridged area gently, then

push the cover in the direction of the arrow and lift.

2 Load the batteries, making sure the polarities (+) and (–) arecorrect. This is marked inside the battery compartment.

Next, you need to tell the remote control to operate the VCR, notthe TV.

Operating the VCR with the Remote ControlThe HS-U449 has two VCR remote control operational settings:VCR-A and VCR-B. The HS-U449 is pre-set to VCR-A setting.See page 43 for information about VCR operational setting.

1 Set the VCR/TV slide switch on the remote control to VCRposition. This “tells” the remote that you want to control theVCR.

Loading a TapeTapes can be loaded into your VCR as long as the VCR is pluggedin. Even when the VCR POWER is off, loading a tape willautomatically turn the VCR on. Use only tapes that have a label.

1 Hold the tape so that the long narrow edge with the contentslabel faces you. The other edge is hinged and should face theVCR. The plastic window that shows the videotape shouldface up.

2 Gently insert the tape evenly into the cassette slot until theVCR automatically takes it in.

If the VCR will not automatically take the tape in, press EJECT andtry again.

Your VCR will eject the tape if it is loaded improperly. If the VCRejects the tape; remove the tape, check to see that the contentslabel is facing you, that the geared tape reels are facing down, waita few seconds, and try again.

Playing a Tape1 Press PLAY on the front panel or the remote control.

The VCR will automatically play the tape at the correct speed.When the VCR reaches the end of the tape, it will automaticallyrewind to the beginning of the tape and stop.

You can stop playing by pressing STOP.

CORRECT

INCORRECT

21 3

54 6

87 9

0

PLAY

STOP

STOPPLAY

Playback

11

Using Basic Playback ControlsRewinding a tapeWhile the tape is stopped, press REW on the remote control or onthe front panel.

Fast forwarding a tapeWhile the tape is stopped, press FF on the remote control or on thefront panel.

Speed Search with pictureWhile the tape is playing press FF for forward speed search withpicture or press REW for reverse speed search. See page 34 foradditional information on searching techniques.

Pausing a tapeWhile the tape is playing, press PAUSE on the remote control or onthe front panel to freeze the picture on the screen.

Press PAUSE a second time to return to normal play.

If you leave the VCR in pause for more than 5 minutes, the VCRwill automatically stop to prevent damage to the tape.

Controlling the Vibration During Still FrameIf the picture vibrates during still frame, press the CHANNEL ª orº on the front panel until the picture is steady.

Unloading a Tape1 Press EJECT on the front panel or on the remote control. If the

VCR POWER is off, the VCR will turn on, eject the tape, thenturn off.

2 Remove the tape.

Using repaired tapesWe recommend that you take any broken or torn tapes to aprofessional for repair. If you repair a torn tape with impropermaterials, you could damage your VCR when you play the tape.

21 3

54 6

87 9

0

REW FF

PAUSE

CHANNEL

REW

PAUSE

FF

21 3

54 6

87 9

0

EJECT

EJECT

Playback

12

Your VCR comes with Mitsubishi’s exclusive on-screen operating system. This system has been developed tosimplify the operation of your VCR with clear, easy-to-understandlanguage and design.

Before your VCR can receive television channels or you canprogram your VCR to record, you need to memorize all of thechannels you can receive into your VCR and set the clock.Fortunately, your VCR makes this an easy process with our menusystem.

When using the on-screen menus, use the ADJUST buttons tomove the highlight bar up or down and to change the setting ofselected features. Press the ENTER button to enter a selection oradjustment. Press the CANCEL button to cancel or clear a setting.

Selecting the On-screen LanguageYou can set your VCR to display on-screen messages, menus, andfunctions in English or Spanish. You will do this the first time youuse the menus or set any audio and video functions.

1 Make sure you are viewing the picture coming from your VCR.Press MENU on the remote control. If this is the first time themenus have been used, you will see the menu for selecting theon-screen language.

2 Press ADJUST buttons on the remote control to highlight thedesired language.

3 Press ENTER on the remote control. The menu will change tothe VCR Main Menu.

4 Press MENU to exit the menus.

IMPORTANTThe Select Language menu is unique. While all othermenus can be accessed at almost any time, the SelectLanguage menu will not automatically appear again after itis first set. To see the Select Language menu, press thePOWER button for about 8 seconds, then follow theprocedure above. The Select Language menu will alsoappear after an extended power failure.

Setting Up Your VCR

54 6

87 9

0

ADJUST

ADJUST

ENTERCANCEL

Press toEnter

Press toCancel

Press toSelect

Select Language

ƒEnglish

ƒEspañol

∫πMENU to go back

∂ ππADJUST to select

≤¥≥πENTER to enter

∑ ππADJUST to select

13

Memorizing Channels AutomaticallyUsing this process, your VCR will automatically memorize all of thetelevision stations available to you. You can later get rid ofunwanted or unused stations.

If your local cable company scrambles some or all stations,and/or requires you to use a cable box, then your ability tomemorize channels would normally be limited. The cablebox receives all of your channels, then sends only one toyour TV and your VCR, usually on channel 3 or 4.

If your cable box or cable system seems incompatiblewith your new VCR, call your cable company. They maybe able to provide solutions to your problems.

1 Set the VCR’s input to tuner. To do this, press INPUT on theremote control until a channel number appears on the screen.

2 Press MENU on the remote control. VCR Main Menu comesup. If First Time Set-Up is not highlighted, use the ADJUSTbuttons on the remote to highlight it.

3 Press ENTER. First Time Set-Up menu will appear. Press theADJUST buttons to select Memorize channels. Press ENTER.

IMPORTANTIf you are playing back a tape or receiving a video signalfrom an external input, Not available will flash and an errormessage will appear. To correct this, stop the tape or turnoff the menus and switch the VCR’s input to tuner.

4 You will see the menu for sources connected to the VCR.Using the list below as a reference, press the ADJUST buttonsto select the kind of antenna you connected.• Cable if you are using any cable combination, including a

cable box with an A/B switch• Indoor/outdoor ant. if you use rabbit ears type or roof

mounted type antennasAfter you have selected, press ENTER.

5 An on-screen message will show you that the VCR ismemorizing the stations you can receive. You can cancel thememorization at any time by pressing CANCEL. After the VCRhas memorized all the channels, the screen will return to theVCR’s picture.

IMPORTANTAutomatic channel memorizing may include vacantchannels if there are stray signals or noise on thosechannels. If this occurs, you can manually delete thechannels using the procedure in the section Adding andDeleting Channels.

∆Memorize channels

What type of sources are

connected to the VCR?

’Cable

”Indoor/outdoor ant.





ƒFirst Time Set-Up

Your choices are:

≈Set the clock


«Add/delete channels





ªVCR Main Menu

Your choices are:

¬Program to record

√Customize choices

ƒFirst Time Set-Up





A special note to cable boxsubscribers

Setting Up Your VCR


Now memorizing all the

stations you can receive

Channel 3

Stand by this may take

a few minutes

To cancel memorization,

press CANCEL

14

Adding and Deleting ChannelsIf necessary, you can manually add or delete channels after youhave completed the automatic channel memorizing.

1 Make sure that video mute is ON. See page 39.

2 Set the VCR’s input to tuner. To do this, press INPUT on theremote control until a channel number appears on the screen.

3 Press MENU on the remote control. VCR Main Menu appears.

4 Press the ADJUST buttons on the remote control to select FirstTime Set-Up. Press ENTER.

5 You will see the First Time Set-Up menu. Press the ADJUSTbuttons to select Add/delete channels. Press ENTER.

IMPORTANTIf you are playing back a tape or receiving a video signalfrom an external input, then Not available will flash on-screen. To correct this, stop the tape or turn off the menusand switch the VCR’s input to tuner.

6 You will see the screen for adding or deleting channels. Usethe ADJUST buttons to select the channel that you want to addor delete. Press ENTER to add the channel; press CANCEL todelete it.

7 When you are finished adding or deleting channels, pressMENU three times to exit the menus.

IMPORTANTIf you use automatic memorizing again, you will lose all of themanual changes you made. All of the channels you deleted willbe added; all of the channels you added will be deleted.

Selecting a ChannelNow that you have memorized channels, and added or deletedsome, you will want to be able to select channels. If you have notyet memorized channels, see page 13, Memorizing ChannelsAutomatically.

Antenna/Cable selections Your VCR can receiveindoor/outdoor antenna VHF/UHF channels 2–69cable antenna cable channels 1–125

If you try to select a channel number that the VCR cannot receive,the VCR will not change channels.

selecting channels sequentiallyPress CHANNEL on the remote control or on the VCR front panel.This will cycle through the channels in sequential numerical order.

selecting channels directlyUse the number buttons on the remote control. For example, tochoose channel 23, press 2-3.To select a single digit channel, such as channel 5; press 5. Youcan also press 5, then press ENTER.

Setting Up Your VCR


Channel 39

Not in memory



≤¥≥πENTER to add

† ∑ ππADJUST to select

≠πππππCANCEL to delete

ƒFirst Time Set-Up

Your choices are:

≈Set the clock







15

Setting the ClockYou have to set the clock using either Setting the Auto Clock orSetting the Clock Manually before you can program your VCR torecord.

Setting the Auto ClockYour VCR can set the clock automatically by picking up a timesignal which some TV and cable channels transmit with theirbroadcasts. Most PBS stations send this signal; however, thisfunction works only if a channel in your area is broadcasting a timesignal. If you don’t receive this signal, set the clock manually.

1 Press MENU on the remote control. VCR Main Menu willappear.

2 Press the ADJUST buttons to select First Time Set-Up. PressENTER. The First Time Set-Up menu will appear. Use theADJUST buttons to select Set the clock. Press ENTER.

3 You will see the Set the clock menu. Auto Clock set will behighlighted. Press the ADJUST buttons to select ON.

4 Turn the VCR off to activate the auto clock setting function.

The VCR will search for a channel that carries a time signal, thenset your time zone and daylight saving time. If there are only a fewchannels in your area that carry time signals, it may take about 30minutes to complete. If you turn the VCR on before the correcttime displays, the auto clock setting will be cancelled. See if theclock has been set on the front panel display on the VCR.

If the VCR displays the wrong time, the time zone setting may notbe correct. To adjust this, follow the steps in If the VCR displaysthe wrong time. (See the next page.)

IMPORTANTThe auto clock function will activate whenever you turn offthe VCR and at 3:00 am, when the VCR power is off. Ifyou use a cable box, make sure that you leave the cablebox on and tuned to the local PBS station to activate theauto clock function.

After a power failure, the VCR will automatically set theclock again. (If you have set the Auto Clock set setting ofthe Set the clock menu to OFF, the auto clock function willnot work.)

Setting Up Your VCR

ƒFirst Time Set-Up

Your choices are:

≈Set the clock







≈Set the clock

ƒAuto Clock set ON OFF





16

If the VCR displays the wrong time

1 Follow the procedure on the previous page to step 3. Thenpress ENTER.

2 You will see the Set the clock menu. Channel will behighlighted. If you know the channel that carries a time signal,press the ADJUST buttons to enter the channel. Most PBSstations broadcast a time signal. For fastest response, enteryour local PBS station. If you don’t know it, leave the channelsetting at AUTO. Press ENTER.

3 Time zone will be highlighted. Press the ADJUST buttons toselect the time zone of your area. Available time zones are:Atlantic, Eastern, Central, Mountain, Pacific, Alaska, andHawaii. Press ENTER.

4 Daylight savings will be highlighted. Press the ADJUSTbuttons to select AUTO, ON or OFF. If you follow daylightsaving time, select ON. If not, select OFF. If you select AUTO,the VCR automatically sets the daylight saving time.

5 To activate the auto clock function, turn off the VCR.

Setting the Clock ManuallySkip this section if your VCR has set the clock correctly using theauto clock function.

1 Press MENU on the remote control. You will see the VCR MainMenu.

2 Press the ADJUST buttons to select First Time Set-Up. PressENTER. First Time Set-Up menu will appear. Press theADJUST buttons to select Set the clock. Press ENTER.

3 You will see the Set the clock menu. Auto Clock set will behighlighted. Press the ADJUST buttons to select OFF. PressENTER.

≈Set the clock

ƒChannel (065)

ƒTime zone (AUTO)

ƒDaylight savings (AUTO)

To activate Auto Clock,

turn off the VCR.





≈Set the clock

ƒChannel (065)

ƒTime zone (Eastern )



turn off the VCR.





≈Set the clock

ƒChannel (065)

ƒTime zone (Eastern )



turn off the VCR.





≈Set the clock

ƒAuto Clock set ON OFF





Setting Up Your VCR

17

4 Daylight savings will be highlighted. Press the ADJUSTbuttons to select ON or OFF. If you are currently followingdaylight savings, select ON. Otherwise, select OFF. PressENTER.

5 Press the ADJUST buttons until the correct month appears onscreen. Press ENTER.

6 Press the ADJUST buttons to set the current year. PressENTER.

7 Press the ADJUST buttons to set the date. Press ENTER.

8 The hour numbers and the am/pm indicator will be blinking.Press the ADJUST buttons to set the hour and am/pm at thesame time. Pressing ADJUST + moves the clock forward;pressing ADJUST – moves the clock backward. Press ENTER.

9 Press the ADJUST buttons to set the minutes. When you haveset the correct time, press ENTER. First Time Set-Up menuwill appear, and the clock will start running.

10 Press MENU three times to exit the menus.

You can adjust the daylight saving time manually. When Daylightsavings is highlighted, press the ADJUST buttons to select ON orOFF.If you select ON, the VCR will set the clock forward one hour.If you select OFF, the VCR will set the clock back one hour.

IMPORTANTAt any time that you adjust this setting, check yourprogrammed recordings to be sure they are set to thecorrect times.

≈Set the clock

ƒDaylight savings ON OFF

ƒMonth --

ƒYear --

ƒDate --

ƒTime --:--Ł





≈Set the clock


ƒMonth March

ƒYear 2003

ƒDate 18 Tuesday

ƒTime 7:00pmŁ





≈Set the clock


ƒMonth March

ƒYear 2003

ƒDate 18 Tuesday

ƒTime 12:00pmŁ





≈Set the clock


ƒMonth March

ƒYear 2003

ƒDate 1 Saturday

ƒTime 12:00pmŁ





Setting Up Your VCR

18

Your new VCR offers a wide variety of recording options that takefull advantage of our advanced electronics. First, you can learnhow to record a current broadcast. Then, in another section of thisbook called Timer Recording, you can learn how to program yourVCR to record at a later time and day.

Recording a Current BroadcastTo record a TV program that is currently playing:

1 Load a tape with its erasure prevention tab intact into the VCR.

2 Set the speed at which you would like to record by pressingSP/EP on the remote control or REC SPEED on the frontpanel. The selected speed will be displayed on the TV screen.

3 Set the VCR’s input to tuner by pressing INPUT until a channelnumber is shown on-screen. If L1 or L2 appears, continue topress INPUT until a channel number appears.

4 Select the channel you wish to record by pressing CHANNELon the remote control or on the front panel or the numberbuttons on the remote. If you are using a cable box, selectchannel 3 or 4 on the VCR, and change the channel on thecable box, not on the VCR. Additionally, if you are using an A/Bswitch, remember to set the switch to the correct position.

5 Press REC on the remote or REC/ REC LENGTH on thefront panel.

Recording will start. When the VCR reaches the end of the tape, itwill automatically rewind to the beginning of the tape and stop.

• You can stop recording at any time by pressing STOP orPAUSE on the remote or on the front panel.

• To resume recording from STOP, press REC.• To resume recording from PAUSE, press PAUSE.

You cannot use REC/ REC LENGTH on the front panel toresume recording from PAUSE.

IMPORTANTIf you pause the VCR for more than five minutes, recordingwill stop automatically to protect the tape.

If you record in extended play (EP), you will only be able toplay the tape on a VCR equipped for EP play, such as thisone.

If you attempt to record on a tape that has had its erasureprevention tab removed, the VCR will eject it. To recordover such a tape, simply place a piece of vinyl tape overthe opening.

21 3

54 6

87 9

0 REC

PAUSE

CHANNEL

INPUT

STOP

SP/EP

CHANNELREC SPEED

SP/EP STOP REC

Erasure prevention tab

Recording

19

Using One-Touch Recording (OTR)One-Touch Recording (OTR) is a way to begin recording immedi-ately, and have your VCR stop recording and turn off automaticallyafter your show is over.


2 Set the speed at which you would like to record by pressingSP/EP on the remote control or REC SPEED on the frontpanel. The selected speed will be displayed on the TV screen.

3 Set the VCR’s input to tuner by pressing INPUT on the remoteuntil a channel number shows on-screen.


5 Press REC/ REC LENGTH on the front panel twice. The firsttime you press the button, recording will begin. The secondpress of the same button adds 30 minutes to the OTR timer,displayed on the front panel.

6 Press REC/ REC LENGTH for each additional 30 minutesyou want to add to the OTR timer, up to 4 hours. If you pressthe button 10 times, you will see End on the front panel display.The VCR will record until the end of the tape. If you press thebutton an eleventh time, the VCR will resume normal manualrecording.

The OTR timer will begin to count down backwards. When itreaches zero, the VCR will stop recording and turn off.

If you program too much time into the OTR timer

Continue pressing REC/ REC LENGTH. After the End point youcan start over from zero, adding time in 30 minute intervals.

How OTR affects other controls

If you press PAUSE during OTR, the VCR will pause recording, butthe OTR timer continues to count down.

Press PAUSE again to resume recording from the record-pausemode. The REC/ REC LENGTH will not resume your recording.

If you press STOP during OTR, you erase the OTR programming.

21 3

54 6

87 9

0

CHANNEL

INPUT

SP/EP

CHANNELREC SPEED

SP/EP REC

2 REC LENGTH

Recording

20

Using Standby One-Touch Recording (OTR2)Standby One-Touch Recording (also called OTR2) is a program-ming method to begin recording within the next 24 hours andrecord in 30 minutes intervals. Before you use OTR2, make surethe clock has been set correctly.


2 Set the speed at which you would like to record by pressing SP/EP on the remote control or REC SPEED on the front panel.The selected speed will be displayed on the TV screen.

3 Set the VCR’s input to tuner by pressing INPUT on the remoteuntil the channel number shows on-screen.


5 Press PAUSE/%START TIME on the front panel to set the timewhen you wish recording to start (within the next 24 hours). Thestart time is displayed on the front panel. The first time display isthe next half-hour increment from the current time. For example,if it is currently 2:15, 2:30 (next half-hour increment) will bedisplayed. Similarly, if it is currently 2:40, 3:00 (again, the nexthalf-hour increment) will be displayed. Each time you press thebutton, the start time is delayed by 30 minutes.

6 Press REC/˙REC LENGTH for each additional 30 minutes youwant to add to the OTR2 timer, up to 4 hours. If you see End on thefront panel display, the VCR will record until the end of the tape.

After 30 seconds, the power will turn off and the programmedrecording light will be lit. The VCR will automatically turn on at theOTR2 start time and recording will begin. When the OTR2 timerreaches zero, the VCR will stop recording and turn off automati-cally. If the end of the tape is reached before OTR2 is finished, theVCR will stop and the power will turn off.

IMPORTANTOther programs you have set to record may be erased if:• the start times are before the OTR2 start time• conflicts with the OTR2

• starts within one minute or less after the OTR2 finishesIf you turn the power on while your VCR is in stand-by forthe OTR2, the OTR2 programming will be erased.

To cancel OTR2

• Turn the power OFF while you are programming the timer.• Turn the power ON if you have finished programming the timer.

How OTR2 affects other controlsIf you press REC/ REC LENGTH on the front panel during OTR2

recording, 30 minutes will be added to the OTR2 timer. If you pressSTOP during OTR2 recording, you erase the OTR2 programming.

21 3

54 6

87 9

0

CHANNEL

INPUT

SP/EP

CHANNEL

REC SPEEDSP/EP

REC

2 REC LENGTH1 START TIME

PAUSE

PM

Recording

21

Using Audio and Video FunctionsThe audio and video function menus allow you to set things suchas listening to the stereo track of your recording, or setting the tapelength to have the remaining time display function work properly.The VCR will display the functions and settings on your TV screen.The first section describes the functions, the next section tells youhow to adjust the functions.

Audio functionsaudio monitornormal record

Video functionstape (length) repeat playbackPerfecTape Select PerfecTape®

counter zero stop Search to blank

Descriptions of Audio Functions

Audio monitor (Listen to:)

This allows you to listen to the various audio tracks that your VCRis capable of recording.

• Choose Stereo to listen to both stereo channels.• Choose L to listen to the left channel of a stereo track.• Choose R to listen to the right channel of a stereo track.• Mono track is lower in quality than the others. The audio

monitor is automatically set to Mono if you are watching atape that was not recorded in VHS Hi-Fi. Set the audiomonitor to Mono to hear SAP signal recorded on the monotrack of a Hi-Fi tape.

IMPORTANTSurround Sound systems: If you have your VCRconnected to a surround sound system, set the audiomonitor to Stereo. Surround sound requires both left andright channels to create the rear channel effects.

While the VCR is not playing a tape, you will see the followingdisplays on the TV screen for 3 seconds when you change thechannel or press DISPLAY.

If you change the channel to: Displaystereo broadcast StereoSAP broadcast SAPstereo and SAP Stereo+SAP

While the VCR is playing a tape, you will see the following displayson the TV screen for 4 seconds when you press DISPLAY.

The audio monitor you listen to DisplayStereo Audio StereoL Audio LR Audio RMono Audio Mono

Recording

22

Recording

Normal recording (Record:)

When your VCR is recording, it actually records the audio portion ofa program twice: once on the stereo Hi-Fi tracks, and once on themono track. Additionally, your VCR can receive Separate AudioProgram (SAP) broadcasts. A SAP broadcast is an alternativesoundtrack for a program; it is often a sound track in anotherlanguage. The SAP broadcast is recorded only on the mono track.

Use the normal recording function to record the SAP broadcast onthe mono track by choosing Stereo+SAP. Otherwise, chooseStereo. In either case, the main program is recorded on the stereoHi-Fi track. Also, if there is no SAP broadcast, the VCR will recordthe main program on the mono track.

Descriptions of Video Functions

Tape

Adjust this function to ensure the accuracy of the Remaining Timedisplay. The remaining time function does not work properly with atape that is less than 30 minutes long.

Length of tape Use Setting2 hours long or less(T-30 through T-120) T-120160 minutes (T-160) T-160180 minutes (T-180) T-180200 minutes (T-200) T-200210 minutes (T-210) T-210

PerfecTape Select (Play PerfecTape)

This function turns on the PerfecTape Select circuitry, whichautomatically maximizes picture quality when playing a worn or poorquality tape.

Set the switch to Soft to soften the picture, set it to Sharp tosharpen it. Set it to Normal when you do not want to use thisfeature. Use Normal on new or high quality tapes. If it is set toAuto, the VCR will automatically select the ideal setting ofPerfecTape Select depending on the condition of the tape.

Counter zero stop (Counter zero stop)

This function is used to automatically fast forward or rewind to“0h00m00s” and stop the tape. See page 35 for more informationon this feature.

Repeat playback (Repeat play)

Use this function to repeatedly play a section of tape between twoindex marks. See page 37 for more information on this feature.

PerfecTape®

PerfecTape function allows you to test the quality of video tapesyou will record on. After each test, the VCR adjusts its circuitry inorder to make the best possible recording on your tape. See page40 for more information on this feature.

23

Search to blank (Search to blank)

Use this function to search the beginning of the blank section of thetape. See page 37 for more information on this feature.

Selecting and adjusting the audio and video functions1 Press AUDIO/VIDEO on the remote control to see the function

menu.

2 Press AUDIO/VIDEO repeatedly until the function you want toadjust appears.

3 Press the ADJUST buttons on the remote to adjust the setting.

The functions will disappear if you do not press any buttons for 5seconds.

IMPORTANTThe audio and video function menus do not appear:• when the VCR menu is displayed• during special effects playback

Tape function does not appear during playback.

PerfecTape Select is displayed only during playback.

PerfecTape displays only when a tape, with its erasure tabintact, is loaded and the VCR is stopped.

21 3

54 6

87 9

0

AUDIO/VIDEO

ADJUST

ADJUST

VCR

Listen to: Stereo

Use ADJUST to select

Recording

24

Mitsubishi offers 2 ways to set your VCR to record upcomingbroadcasts. Choose from:

Conventional VCR timer recordingQuick Program (easy) -- VCR does not need to be ON to

begin programming

You can schedule up to 8 recording events within a one monthperiod.

Clock must be set before any timer recordings can be performed.

Conventional VCR Timer Recording1 Load a tape with its erasure prevention tab intact into the

VCR.

2 Press MENU. VCR Main Menu appears on your screen.Use the ADJUST buttons to select Program to record.Press ENTER.If there is at least one programmed recording alreadyentered, you will see the Recap screen. Wait 4 seconds,and the Program to record menu will appear.

IMPORTANTIf you have already programmed 8 recording events,Program memory is full will appear on your screen for 3seconds, and then the Recap screen will appear. UseCANCEL to erase an entry before you can add anotherone.

3 Program to record menu appears. Press the ADJUSTbuttons to choose the channel you would like to record; forexample, channel 2. Press ENTER.• If you are using a cable box, enter the channel number

on which the cable box sends a signal to your VCR(usually channel 3 or 4).

• To record from an external source, press INPUT or pressthe ADJUST buttons to:Select External L1 for a source connected to the rearpanel.Select External L2 for a source connected to the frontpanel.

4 Day will flash. Press the ADJUST buttons to choose the dayon which you want to record; for example, Monday the 10th.Your choices are:• a single day up to one month away• every day from Monday through Friday; for example, to

tape a soap opera. To program, press the ADJUSTbuttons until Monday-Friday appears.

• the same day every week; for example, to tape yourfavorite weekly sitcom. To program, press the ADJUSTbuttons until Every and the desired day of the weekappears.

Press ENTER once you have made your choice.

ªVCR Main Menu

Your choices are:

¬Program to record


ƒFirst Time Set-Up





¬Program to record

CH DAY ON OFF

§ 10 TH13 9:00pm 10:30pm SP

--- -- --:-- --:-- SP

--- -- --:-- --:-- SP

--- -- --:-- --:-- SP





Recap screen

Timer Recording

¬Program to record

ƒChannel 2

ƒDay --

ƒStart time --:--

ƒStop time --:--

ƒRecord speed AUTO





¬Program to record

ƒChannel 2

ƒDay Monday 10

ƒStart time --:--

ƒStop time --:--

ƒRecord speed AUTO





25

5 The hour numbers of the start time will flash. Press theADJUST buttons to set the hour when recording is to start.Press ENTER.

6 The minute numbers of the start time will flash. Press theADJUST buttons to set the minutes when recording is tostart. Press ENTER.

7 Set the stop time the same way as the start time, usingsteps 5 and 6.

8 Press the ADJUST buttons to set the recording speed:SP = standard play; EP = extended play; AUTO = auto.Auto speed programming is discussed on page 28. PressENTER.

IMPORTANT

If you press ENTER when you set the timer recordingincompletely, Current Program is not completed will appearon your screen.

If two programmed recording times overlap, VCR is alreadyprogrammed for that time will display on your screen forabout 3 seconds, and then the Recap screen will appear.The program you have just set will be highlighted inmagenta color and flash for 3 seconds. The start and stoptime of the overlapped program will be highlighted in cyancolor. You will need to erase one of them.

9 The programmed memory will appear on the Recap screen.

10 To program additional recording times, select an emptyprogram line by pressing ADJUST buttons. Press ENTER.The Program to record menu will appear. Continue theprogramming procedure from step 3.

11 When you are finished with all programming, check the following:• If you have a cable box, leave the cable box turned ON

and tuned to the station you wish to record. Additionally, ifyou are using an A/B switch, remember to set the switchto the correct position.

• Turn the VCR power OFF and make sure the programmedrecording light is lit.

IMPORTANTWhen programmed recording of 4 and under are entered,only 4 of the 8 program lines appear on the Recap screenat any one time. To see additional program lines, press theADJUST buttons to scroll the lines on the screen.

Canceling a recording in progressThere are two ways to cancel a recording in progress:

Press STOP. The recording stops, but the program is notcancelled. Therefore, if you press REC, the recording will startagain.

Press POWER on the front panel. The recording stops and theprogram is cancelled.

21 3

54 6

87 9

0

STOP STOP

Programming not cancelled

¬Program to record

ƒChannel 2

ƒDay Monday 10

ƒStart time 11:30am

ƒStop time 1:30pm

ƒRecord speed SP





Recap screen

¬Program to record

CH DAY ON OFF

10 TH13 9:00pm 10:30pm SP

§ 2 MO10 11:30am 1:30pm SP

--- -- --:-- --:-- SP

--- -- --:-- --:-- SP





¬Program to record

ƒChannel 2

ƒDay Monday 10


ƒStop time --:--

ƒRecord speed AUTO





Timer Recording

POWER

Programming cancelled

26

Changing while programmingTo change one of your settings (such as start time) while you areprogramming:

Press ENTER to move forward through the program list.Press CANCEL to move backward.Then use the ADJUST buttons to change the setting.

You will cancel the entire program if you press CANCEL while thechannel number is flashing.

Quick ProgramQuick Program is an exclusive Mitsubishi feature that simplifiesthe process of programming your VCR to record. When you pressQUICK PROGRAM on the remote control, you will immediatelysee the Program to record menu and can begin programming rightaway.

You can use this feature even when the VCR is stopped, playing,fast forwarding, rewinding, or off. (Quick program does not workwhile a tape is recording.)

1 Press QUICK PROGRAM on the remote control. If the VCRis off, it will turn on. After tuning your TV to the correctchannel or input, Program to record menu will appear.

IMPORTANTIf the VCR memory is full, Program memory is full willappear for 3 seconds, and then the Recap screen willappear. Use CANCEL to erase an entry before you canadd another one.

2 Complete steps 3 through 9 in Conventional VCR timerrecording. (See page 24.) When you have finished, pressQUICK PROGRAM again.

If the VCR is stopped, it will turn off and be ready to recordyour program at a later time.

If the VCR is playing, fast forwarding or rewinding, themenus will turn off, but the VCR power will remain on.

3 When you are finished with all programming, check thefollowing:• If you have a cable box, leave the box turned ON and

tuned to the station you wish to record. Additionally, if youare using an A/B switch, remember to set the switch to thecorrect position.

• Make sure the VCR is turned OFF and the programmedrecording light is lit before the recording time.

IMPORTANTIf you press QUICK PROGRAM, but the clock is not set, Setthe clock menu will appear. Set the clock manually.

21 3

54 6

87 9

0

QUICK PROGRAM

¬Program to record

ƒChannel --

ƒDay --

ƒStart time --:--

ƒStop time --:--

ƒRecord speed AUTO





Timer Recording

87 9

0

ADJUST

ADJUST

ENTER

CANCEL

forward

backward

adjust

¬Program to record

CH DAY ON OFF

§ 2 WE12 11:30am 1:30pm SP

10 TH13 9:00pm 10:00pm EP

7 E-WE 8:00am 9:00am EP

12 FR14 5:30pm 5:45pm EP

8 TU18 11:00pm 0:30am SP

13 M-F 7:00pm 7:15pm EP

15 SU30 8:00pm 9:00pm EP

46 SU16 7:00am 9:00am SP

Recap screen

27

Timer Recording HintsTo use the VCR before timer recording begins, press POWER onthe remote once. This turns the programmed recording light offand the VCR on. If you use POWER on the front panel for thispurpose, press it twice. Pressing it once turns off the programmedrecording light; pressing it again turns the VCR on.

When you are finished using the VCR, turn the VCR power offagain. Make sure the programmed recording light is back on.

After a program has been recorded, the VCR memory of thatprogram is cleared (unless you have scheduled the VCR to recordthe program every day or every week).

If there is already a program in the VCR’s memory, you will see theRecap screen when you bring up the menus for programming torecord (unless you are programming with the QUICK PROGRAM).If the VCR’s memory is full, Program memory is full will appear onthe screen. If so, you must erase a program before you can entera new one.

If a tape runs out during timer recording, the VCR ejects the tapeand the programmed recording light ( ) and the cassette light( ) will flash. Load a new tape and press REC. Recording willresume.

If you forget to load a tape, the programmed recording light ( )and the cassette light ( ) will flash when you turn the VCRpower off. (A tape without an erasure tab will be ejected. Tocorrect this, load a tape with its erasure tab intact, and turn off theVCR.)

Do not overlap the recording times you enter into the VCR. If youset two programmed recording times overlap, VCR is alreadyprogrammed for that time will appear on your screen.

Remember that the VCR will record over the next section of tape.If you want to save a tape, remove it and instead use a differenttape for a new recording.

Your VCR will not record over a tape that has the erasureprevention tab removed. All rental movies have this tab removed,so they are safe from being accidentally erased.

21 3

54 6

87 9

0

REC

VCRPOWER

POWER REC

Timer Recording

28

Auto speed programmingUse auto speed programming if you want to record as much of theprogram as possible in standard play (SP) speed, but you want theVCR to automatically switch to extended play (EP) if there is notenough tape left.

Auto speed programming is only available for one program. In thefirst slot, the recording speed default is AUTO.

Make sure that the Tape video function matches the length of tapeyou are using. See Selecting and adjusting the audio andvideo functions on page 23.

At the point where the recording mode changes from standardplay (SP) to extended play (EP), some noise may be in the pictureor sound when playing the tape.

Program cautionIf your VCR is set to record, but the power is still ON within 3minutes before timer recording starts, this screen will appear toremind you to turn off the VCR.

If the VCR is still turned on 12 seconds before the start time of therecording, that timer recording will be cancelled.

TV programs that end on the day afterIf you want to start the recording at 11:00 PM and end it at 2:00AM the next day, simply set the start time to 11:00 PM on therecording start day and the end time to 2:00 AM. There is no needto change the day of the week.

Program skip using menusSometimes you may want to skip one day of a timer recording butdo not want to erase it. Program skip will prevent the recording,for that day only, of a program you have scheduled to record everyday or every week.

1 Press MENU on the remote control. Your VCR will turn onand VCR Main Menu will appear. Press the ADJUSTbuttons to select Program to record. Press ENTER.

2 Recap screen will display for 4 seconds. While this screenis displayed, press the ADJUST buttons to place the cursorarrow next to the program you wish to skip.

3 Press STOP. The cursor arrow will change to a X.

4 Press MENU twice to exit the menus.

To resume recording every day or every week, change the X tothe cursor arrow by following steps 1 to 4 again.

¬Program to record

CH DAY ON OFF

2 MO10 11:30am 1:30pm SP

10 TH13 9:00pm 10:00pm EP

X 2 M-F 8:00am 8:30am SP

--- -- --:-- --:-- SP

Use STOP to skip on/off




REC in 3 min

Turn off VCR

program caution

¬Program to record

CH DAY ON OFF

2 MO10 11:30am 1:30pm SP

10 TH13 9:00pm 10:00pm EP

§ 2 M-F 8:00am 8:30am SP

--- -- --:-- --:-- SP

Use STOP to skip on/off




Timer Recording

29

Program skip using the POWER buttonIf you have entered only one program into your VCR’s memory,you can skip the program without going into the VCR’s menus.Simply press POWER on the front panel once. The programmedrecording light will turn off, and the program will be skipped. If youdecide not to skip the program, press POWER on the front paneltwice, the programmed recording light will light up again.

Changing timer recording settings1 Press MENU on the remote control. Your VCR will turn on

and VCR Main Menu will appear. Press the ADJUSTbuttons to select Program to record. Press ENTER.

2 Recap screen will display for 4 seconds. While this screenis displayed, press the ADJUST buttons to place the cursorarrow next to the program you wish to change. PressENTER. You will see the Program to record setting menu.

3 Press ENTER repeatedly to select the item you wish tochange. Use the ADJUST buttons to change it. Then pressENTER repeatedly to return the altered program to theRecap screen.

4 Press MENU twice to exit the menus. Then press POWERto turn off the VCR. Make sure the programmed recordinglight is on.

Canceling a timer recording before the recording starts1 Press MENU on the remote control. Your VCR will turn on

and VCR Main Menu will appear on your screen. Use theADJUST buttons on the remote control to select Program torecord. Press ENTER.

2 Recap screen will display for 4 seconds. While this screenis displayed, press the ADJUST buttons to place the cursornext to the program you wish to cancel.

3 Press CANCEL. The program is erased.


Memory backupIf the VCR is without power for 3 minutes or less, it will retain theclock and the programmed settings. The VCR must have beenplugged in for at least an hour beforehand to charge this backup.If the power is lost for more than 3 minutes, the time and theprogrammed settings will be lost.

If you have set the Auto Clock set setting of the Set the clockmenu to ON, the auto clock function will automatically set the clockagain when power is restored.

¬Program to record

CH DAY ON OFF

§ 2 MO10 11:30am 1:30pm SP

--- -- --:-- --:-- SP

--- -- --:-- --:-- SP

--- -- --:-- --:-- SP





Recap screen

Timer Recording

¬Program to record

ƒChannel 2

ƒDay Monday 10


ƒStop time 1:30pm

ƒRecord speed EP





¬Program to record

CH DAY ON OFF

§ 2 MO10 11:30am 1:30pm SP

--- -- --:-- --:-- SP

--- -- --:-- --:-- SP

--- -- --:-- --:-- SP





Recap screen

30

1 Connect the audio cable to AUDIO OUT Land R on the playback VCR and to AUDIOIN L and R on the HS-U449. If the playbackVCR is mono, use only the AUDIO IN L onthe HS-U449.

2 Connect a video cable to VIDEO OUT onthe playback VCR and to the VIDEO IN onthe HS-U449.

3 If the playback VCR is Hi-Fi, set the audiomonitor to Stereo.

4 Use INPUT to set the HS-U449 to ExternalL1 if you used the HS-U449 rear paneljacks, or External L2 if you used the HS-U449 front panel jacks.

Using Two VCRs to CopyThere are two basic ways to make a copy of a tape.One way is to use the HS-U449 to record and another VCR for playback.The other way is to use another VCR to record and use the HS-U449 for playback.

Regardless of which method you may choose, you will need one RCA audio cable and one RCA videocable to connect the two VCRs. If you do not have these cables, they are available at your local electronicsdealer.

VIDEO IN L/MONO - AUDIO IN - R

L R L R

RECORDING PLAYBACKHS-U449

AUDIO IN 2 R

AUDIO IN 2 L/MONO

AUDIO OUT L

AUDIO OUT R VIDEO OUTVIDEO IN 2

Using the HS-U449 to record from another VCR

Editing Features

5 Put a blank tape into the HS-U449.

6 Put the tape you want to copy into theplayback VCR and find the cue point. PressSTOP if the picture starts playing.

7 On the HS-U449, press REC, then PAUSE.

8 On the playback VCR, press PLAY, thenPAUSE.

9 Press the PAUSE buttons on both VCRs atthe same time to begin copying the tape.

10 When finished, press STOP on both VCRs.

31

R

OUTAUDIO

L

R

VIDEO

OUT

LR L

HS-U449 RECORDINGPLAYBACK

AUDIO OUT L

AUDIO OUT R AUDIO IN R

AUDIO IN LVIDEO INVIDEO OUT

Using the HS-U449 to playback to another VCR

1 Connect one stereo audio cable to AUDIOIN L and R on the recording VCR, and toAUDIO OUT L and R on the HS-U449.

2 Connect a yellow video cable to VIDEO INon the recording VCR and to VIDEO OUTon the HS-U449.

3 Set the audio monitor on the HS-U449 toStereo. If the other VCR is a mono VCR,set the audio monitor on the HS-U449 toMono. See Selecting and adjusting theaudio and video functions on page 23.

4 Set the input of the recording VCR toExternal.

5 Put a blank tape into the recording VCR.

6 Put the tape you want to copy into theHS-U449 and find the cue point.

7 On the recording VCR, press REC, thenPAUSE.

8 On the HS-U449, press PLAY, then PAUSE.

9 Press the PAUSE buttons on both VCRs atthe same time to begin copying the tape.

10 Press STOP on both VCRs when you arefinished.

Editing Features

32

Advanced Playback ControlsSpecial effectsYou can use FF and REW on the front panel, or the I\ and Îon the remote to control the playback speed of the tape.

Using the FF and REW on the front panel to control the playback

speed

1 While the VCR is playing a tape, press PAUSE to freeze thepicture.

2 Press the FF or REW on the front panel. Each press of FFchanges the playback speed by one step in the forwarddirection. Each press of REW changes the speed by one stepin the reverse direction. (See the chart below.)

3 To resume normal playback, press PLAY.

Using the I\\\\\ and Î on the remote to control the playback speed

1 While the VCR is playing a tape, press I\ or Î on theremote control. Each press of I changes the playbackspeed by one step in the forward direction. Each press of I\changes the speed by one step in the reverse direction. (Seethe chart below.)


After about 5 minutes in the still or slow-motion mode, the VCR willautomatically stop to avoid damage to the tape. The picture mayvibrate vertically when you pause the VCR’s picture.

Still adjustment

Sometimes during still frame, the picture may vibrate or shake. Tocorrect this problem, press CHANNEL on the front panel until thevibration is reduced or stops. Side-to-side vibration cannot becorrected.

CHANNEL

21 3

54 6

87 9

0

INDEX

REW FF

1/30 reverse slow-motion playback1/10 reverse slow-motion playback

1/5 reverse slow-motion playbackReverse playback

Reverse speed searchReverse high speed search

Reverse fast playbackPress FF on the front panelor ^| on the remote control

Press REW on the front panel or |\ on the remote control

High speed search Speed search

Fast playback

1/5 slow-motion playback1/10 slow-motion playback

1/30 slow-motion playbackStill

Playback

Advanced Features

33

Double speed playback

You can see the contents of the videotape in double speedplayback.

1 While the VCR is playing a tape, press X2. You’ll see thepicture in double speed playback. The sound will be muted. Acertain amount of noise in the picture is normal.


Adjusting the Trackingautomatic tracking

When you start playback of a newly inserted tape, your VCRautomatically adjusts the tape to give you the best quality picture.

A certain amount of “noise” in the picture or sound is normal whilethe VCR is tracking a tape.

manual tracking

From time to time, you might play a tape that has excess noise inthe picture, often looking like vibration or interference at the top orbottom of the screen. To correct the picture, you have to manuallytrack the tape.

1 While the tape is playing, press CHANNEL on the front paneluntil the picture is clear of excess noise.

2 To continue automatic tracking, press both front panelCHANNEL at the same time. Automatic tracking will alsoresume when you eject the tape.

slow tracking

Slow tracking is used to adjust the playback quality during slowmotion playback and still frame. You can only use slow tracking ifyour tape was recorded in extended play (EP) speed. To adjustthe slow tracking, put a tape into slow motion, then press CHAN-NEL on the front panel until the best picture is obtained.

21 3

54 6

87 9

0

X2

CHANNEL

Advanced Features

34

Time CounterYour VCR has a time counter that shows the amount of time thetape has run in hours, minutes, and seconds. This counter isuseful when you want to find specific points on a tape. Thecounter will not work when playing blank tapes or on blank sectionsof tape, or when the VCR’s power is off.

to make the time counter appear:

Press DISPLAY. The time counter will appear on the TV screen. Itwill disappear after 4 seconds when playing a tape. To turn off thedisplay, press DISPLAY twice.

setting the counter

To set the counter to “0h00m00s,” press CANCEL on the remotecontrol.

You cannot reset the counter if you are using the VCR’s menus.

The counter will reset to “- h - - m - - s” when you eject a tape.When you load a tape again, the counter will display “0h00m00s”.

Searching TechniquesYour VCR lets you search through a tape in a number of ways.These include:

Quick search (CM skip) -- 30 second intervalsSpeed search -- visually searchCounter zero stop -- direct to start of recordingIndex search -- find specific index pointsSearch to blank -- find the beginning of the blank section

Quick search (CM skip)Quick search lets you skip over the tape you are playing in about30 second intervals. It is designed so that you can quickly speedthrough any commercials you may have recorded. To do this:

1 Make sure that you have set the VCR/TV slide switch on theremote control to the VCR position.

2 While playing a tape, choose the desired search time bypressing a number button.

The VCR will speed through the selected length of tape, thenresume playback. This screen will show the search time and thegauge. Each mark on the gauge represents 15 seconds. Themarks will disappear, one by one, every 15 seconds of the searchtime. You can select a search time up to 3 minutes.

CM Skip

3m00s

§§§§§§§§§§§§

Numberbutton

Searchtime

1 2 3 4 5 6

30 sec. 1 min. 1 min.30 sec. 2 min. 2 min.

30 sec. 3 min.

Advanced Features

VCR

Stop

⁄‡‚‡‡‡‡‡‡‹

REM 1:40

0h20m08s

Time counter

35

Speed searchUse speed search to visually search through the contents of avideotape.

1 While playing a tape, press FF or REW on the front panel or onthe remote control. You will see the picture as it fast forwardsor rewinds. Noise bars may appear in the pictures.

2 If you press FF or REW and hold it down for about 1 second,the search speed will increase.

3 To resume normal playback, press FF or REW again quickly, orpress PLAY.

IMPORTANT

The fastest search speed that allows you to see the pictureis about 30 times normal speed. It is normal for thenumber of noise bars on the screen to increase and rollfrom top to bottom as the visual search speed increases.Using speed search for long stretches of tape may causethe video heads to become dirty faster.

The fastest way to move through the tape is without apicture, which allows you to search up to 500 times normalspeed. To do this, press STOP, then FF or REW. If youpress and hold FF or REW for more than 2 seconds, thesearch speed will slow to 330 times normal speed.

In order to protect your tapes and the VCR heads, the FastForwarding/Rewinding Speed will be slower than 500xunder the following conditions:1 Use of tapes shorter in length than T-120 (for example,

T-30, T-60, T-90).2 Activating fast forwarding or rewinding from the middle

of the tape.

Counter zero stopCounter zero stop allows you to quickly access the beginning of arecorded or playback section of a tape. The counter zero stop willautomatically fast forward or rewind the tape to “0h00m00s” andstop.

1 Press CANCEL on the remote control at the point you wish tolocate later. The counter will reset to “0h00m00s”.

2 When you wish to return to the point specified in step 1, pressAUDIO/VIDEO on the remote control. The function menuappears on your screen. Press AUDIO/VIDEO until theCounter zero stop function appears.

3 Press ENTER to start the counter zero stop.

The VCR will automatically search to the counter “0h00m00s” andthen stop. The VCR may stop slightly before or after the counter“0h00m00s”.

21 3

54 6

87 9

0

REW

FF

STOP

Advanced Features

VCR

Counter zero stop

Use ENTER to start

36

Index searchIndex search is a way to find specific points on a tape. Beforeusing index search, index marks are placed at specific places on atape. Index search is used to find these marks. Index marks areadded automatically whenever your VCR starts a new recording;you can also add index marks manually at any point duringrecording.

automatic index marks

Whenever recording begins at the STOP mode, an index mark isautomatically added to the tape. A message will indicate that themark is being recorded.

Index marks are not added when you press PAUSE or REC tobegin recording from the record-pause mode.

manual index marks

To add an index mark yourself, press REC on the remote controlwhile a tape is recording.

Index marks must be added at least one minute apart.

1 When the tape is stopped, press INDEX Î to begin aforward search; press INDEX I\ to search in reverse. TheVCR will fast forward or rewind and index search displayappears on the TV.

Once the VCR finds an index mark, it will begin playing backthe tape from that point.

2 You can press INDEX Î or INDEX I\ buttons up to 19times to search for that many index marks. For example, tofind the third index mark ahead, press INDEX Î three times.The on-screen display will count down the number of markspassed before playback begins.

3 To cancel index search, press PLAY or STOP.

Advanced Features

21 3

54 6

87 9

0

INDEX

STOP

REC

VCR Looking

for index+ 1

⁄‡‚‡‡‡‡‡‡‹

REM 1:40

0h20m08s

37

repeat playback

You can playback a section of tape over and over using repeatplayback. The tape will play until the next index mark, rewind tothe previous index mark, and resume playing. If there is only oneindex mark on the tape, then the VCR will play or rewind to thatmark and resume playback. If there is no index mark, the entirecassette will repeat.

1 Press AUDIO/VIDEO on the remote control to display thefunction menu. Press AUDIO/VIDEO until the Repeat playfunction appears.

2 To start the playback, press ENTER.

When the VCR encounters the next mark or the end of thetape, it will automatically rewind to the previous mark and beginplayback again.The VCR will also search for a blank section of tape. If theVCR encounters any blank sections longer than 4 seconds inlength, the repeat playback will begin.

3 Press STOP to cancel the repeat.

Search to blankThis feature allows you to find the end point of the recorded part ofthe tape. The VCR will stop automatically at the beginning of theblank section of a tape.

1 Press AUDIO/VIDEO on the remote control to display thefunction menu. Press AUDIO/VIDEO until the Search to blankfunction appears.

2 To start the search, press ENTER.

When the VCR encounters the blank section of a tape, it willautomatically stop.

IMPORTANT

This feature may not work correctly when the end point ofthe recorded part is within 5 minutes in SP mode (15minutes in EP mode) from the current position.

VCR

Repeat play

Use ENTER to start

Advanced Features

VCR

Search to blank

Use ENTER to start

38

Displaying the Time Gauge and theRemaining TimeThe time gauge is a graphic representation of your position on avideo tape. The left side of the gauge is the tape start (S), and theright side is the tape end (E). For a T-120 length tape played atstandard (SP) speed, each mark on the gauge represents about 15minutes. The remaining time display shows the time, in hours andminutes, left until the end of a tape.

the time gauge and the remaining time automatically appearduring:

fast forward and rewind (from a stopped tape)counter zero stopindex searchesrewinding for repeat playback

Turn off the time gauge and the remaining time by pressingDISPLAY twice.

to make the time gauge and the remaining time appear:

Press DISPLAY once. The time gauge and remaining time appearon the TV screen. They disappear after 4 seconds when playing atape.

To turn off the display, press DISPLAY twice.

IMPORTANTThe time gauge and remaining time work by detectingcontrol signals on recorded tapes. Therefore they do notfunction while playing blank tapes.

The remaining time display may not show the correct remainingtime if the Tape function is incorrectly set, if you are using speedsearch, if you are using a special length cassette (such as T-10length), or if you are using a VHS-C tape with an adapter. Theremaining time display may not work correctly depending on yourtape.

Displaying the Current TimeThe current time is shown on the front panel display or the TVscreen. If you have not set the clock, or if there has been a powerfailure of longer than 3 minutes, the display will show - : - -.

To see the current time on the TV screen:

1 Press DISPLAY twice. The remaining time display will bereplaced by the current time.

2 To turn off the current time, press DISPLAY again.

VCR

Stop

⁄‡‚‡‡‡‡‡‡‹

REM 1:40

0h20m08s

Time gauge

Remaining time display

VCR

Stop

⁄‡‚‡‡‡‡‡‡‹

Sun 8:30p

0h20m08s

Current time display

Advanced Features

VCR

PM

PWR.

Current time display

39

Customize Choices MenuIn the Customize Choices menu, there are 5 options that you canset. For each of the 5 options, start with these 2 steps:

1 Press MENU on the remote control. VCR Main Menu appearson your TV.

2 Use the ADJUST buttons on the remote to select Customizechoices. Press ENTER.

Video muteWhen you turn video mute ON, any blank section of tape or manystations with a weak signal will be replaced by a blue screen. Thesound will also be turned off. When you would like to try to tune inon a weak station, turn video mute OFF.

3 Complete steps 1 and 2 above. Customize choices menuappears. Use the ADJUST buttons to select Video mute.Press ENTER to set video mute to ON or OFF.


IMPORTANT

Video mute function may not work properly when youplayback a section of a tape where only audio signals arerecording.

Auto power save (auto-off)When the Auto Power Save feature is turned on, the VCR willautomatically turn off after remaining idle for 30 minutes. If acontrol, such as a menu function or channel selection, is used or ifthere is a tape playing or being recorded, the VCR will remain on.

3 Complete steps 1 and 2 above. Customize choices menuappears. Use the ADJUST buttons to select Auto power save.Press ENTER to set to ON.


IMPORTANTWhen viewing broadcast stations through the VCR,3minutes>Power off will appear on the TV screen threeminutes before the VCR power turns off. The display willcount down the number of minutes until the VCR turns off.If you want to continue using the VCR, press any of thebuttons.


ƒVideo mute ON OFF

ƒAuto power save ON OFF

ƒRF converter ON OFF

ƒAuto PerfecTape ON OFF

ƒRental Xpress ON OFF



≤¥≥πENTER to change


ªVCR Main Menu

Your choices are:

¬Program to record


ƒFirst Time Set-Up






ƒVideo mute ON OFF









Advanced Features

40

RF converterIf your TV has audio and video inputs, turn the RF converter OFF.If your TV does not have audio and video inputs, keep the RFconverter set to ON. It is preset by the factory to ON.

3 Complete steps 1 and 2 on the previous page. Customizechoices menu appears. Use the ADJUST buttons to select RFconverter. Press ENTER to select ON or OFF.


IMPORTANTIf the RF converter is set to ON, you aren’t required topress VCR/TV to play a tape or to use VCR menus. TheVCR light will automatically light up when you press PLAYor MENU. Be sure to set the TV to the video channel (Seepage 9).

PerfecTape®

PerfecTape® is an exclusive Mitsubishi feature that tests the qualityof video tapes you will record on. After each test, the VCR willadjust its internal circuitry in order to make the best possiblerecording on your tape.

setting up Auto PerfecTape

You can set up PerfecTape® to function two ways.

If you want the VCR to automatically test any non-recorded tapeswhen the tape is loaded, set Auto PerfecTape to ON.

If you do not want the VCR to automatically test tapes, select OFF.PerfecTape® will now function only when you start a test. Any tapewith the erasure prevention tab intact can be manually tested.

It will not automatically test recorded tapes – you must choose totest those yourself.

3 Complete steps 1 and 2 on the previous page. Customizechoices menu appears. Use the ADJUST buttons to selectAuto PerfecTape.

4 Press ENTER to set Auto PerfecTape to ON or OFF.


using PerfecTape® automatically

1 Load a tape that has not been recorded into the VCR.

The VCR will display the testing status screen. When testing, theVCR records for one second, then evaluates the recording it made.The entire test takes about 8 seconds. If you wish to cancel thetest, press STOP on the remote.

When the test is done, the VCR will display the rating of your tapefor 8 seconds, indicating that the VCR has set its internal circuitryto make the best possible recording on this tape.


ƒVideo mute ON OFF









PerfecTape

Band

High ¤°°°°°°°°°‡‡‡‡‡‡‡›

Mid. ¤°°°°°°°°°°°‡‡‡‡‡›

Low ¤°°°°°°°°°°°‡‡‡‡‡›

Test is completed.


ƒVideo mute ON OFF









Advanced Features

41

using PerfecTape® manually

1 Load a tape that has its erasure prevention tab intact into theVCR.

2 Find a portion of the tape that is OK to record over; this featurewill record over one second of your tape.

3 Press AUDIO/VIDEO on the remote control. Function menuappears. Press AUDIO/VIDEO until the PerfecTape functionappears.

4 Press ENTER on the remote to begin the test. To cancel thetest while testing, press STOP on the remote.

When the test is finished, the VCR will display the rating of yourtape for 8 seconds. Turn off the display by pressing STOP on theremote control.

If you wish to erase the settings, eject the tape. The settings willbe erased if the VCR loses power. After the test is finished, thePerfecTape function will not appear unless the tape is ejected.

Rental XpressRental Xpress is a feature, when activated, that will automaticallyrewind the tape to the beginning, eject and power off the VCR,after it has reached the blank section of 30 seconds or longer onany rental tape (or any tape with the erasure prevention tabremoved). To activate this feature:

3 Complete steps 1 and 2 on page 39. Customize choices menuappears.

4 Press the ADJUST buttons to select Rental Xpress. PressENTER to select ON or OFF.


IMPORTANTWhile the VCR is rewinding to the beginning of the tape,you cannot use repeat playback, counter zero stop andindex search.

VCR

PerfecTape

Use ENTER to start


ƒVideo mute ON OFF









Advanced Features

42

Advanced OptionsUsing the remote control to operate your TVThe HS-U449 remote control can operate many of the frequently-used functions of your TV. You only need one remote to operateboth your VCR and TV.

The HS-U449 remote control is pre-set to operate Mitsubishitelevisions, but it can also operate TVs from other manufacturers.To set your remote control for your particular brand of television,follow these instructions.

setting up your remote control to operate your TV

1 Turn off your TV.

2 On the HS-U449 remote control, set the VCR/TV slide switch tothe TV position.

3 While holding in SP/EP, press the code button listed thatcorresponds to the brand of your TV.

4 Press TV POWER on the HS-U449 remote control. Once yourTV has turned on, your remote is set up to operate your brandof TV.

If your TV does not turn on, repeat step 3 using the next codelisted for the brand of your TV.

If none of the codes listed for the brand of your TV work, thenrepeat step 3 several times, using a different code button until oneworks. The possible code buttons are: 0, 1-9, MUTE, VOLUMEª,º, CHANNELª,º and INPUT.

You do not need to perform this set-up again until you change thebatteries, set up your remote for another brand of television, or youget a new TV.

Once you have correctly set your remote control to operate yourTV, you will be able to use the TV POWER, CHANNEL, VOLUME,and number buttons to operate your TV.

IMPORTANTBecause of variations among models, some or all buttonsmay not work, or they may operate different functions thanexpected for your particular TV. If this occurs, you mayneed to use your TV remote control.

Sometimes manufacturers will change the remote controlcodes for their products, or they will use more than onecode. If this is the case, your remote may not be able tocontrol your TV.

When you replace the batteries in your remote, the remotemay return to its initial setting (code button 1). Repeat thesteps above to reset your remote control. If you enter anew code, the previous code will be erased.

MitsubishiFisherG.E.GoldstarHitachiJVCMagnavoxNECPanasonicPioneerPhilipsProscanQuasarRCASanyoSharpSonyToshibaZenith

1, 2, 30VOLUME ª2, 98MUTE42, 9CHANNELª,º64VOLUME ªCHANNELºVOLUMEª 03, 5VOLUMEº7INPUT

Brand of TV Brand codebuttons

Advanced Features

43

operating your TV with the HS-U449 remote control

1 Set the VCR/TV slide switch to TV position on the HS-U449remote control to tell the remote that you want to operate the TV.

2 Point the remote control towards the TV and press the desiredbuttons. To once again control the VCR, set the VCR/TV slideswitch to VCR position.

To program the HS-U449 to respond to VCR-B signalsThe HS-U449 has two remote control operational settings, VCR-Aand VCR-B. Both signals are available so that you may separatelycontrol two Mitsubishi VCRs that are placed closely together.However, the remote control for the HS-U449 will only send VCR-Asignals. By setting the HS-U449 to respond to VCR-B signals, youwill NOT be able to operate the HS-U449 using the remote controlthat came with this VCR. Other selected Mitsubishi VCR remotesand TV remotes are capable of sending both VCR-A and VCR-Bsignals.

to program the HS-U449 to respond to VCR-B signals1 Make sure the HS-U449 is plugged in but turned off. On the

VCR front panel, press REC SPEED and REW at the sametime. To confirm that the VCR responds to VCR-B signals, bappears on the front panel display.

to reprogram the HS-U449 to respond to VCR-A signals again

1 Make sure the HS-U449 is plugged in but turned off. On theVCR front panel, press REC SPEED and FF at the same time.To confirm that the VCR responds to VCR-A signals, A appearson the front panel display.

Child LockThe child lock feature prevents others from using your VCR. Tolock the VCR:

1 Press and hold down DISPLAY on the remote control for about8 seconds. “LOC” will appear on the front panel display for 4seconds.

When the child lock feature is in use, LOC display will reappearwhen you press any of the buttons.

2 To cancel the child lock, press and hold down DISPLAY forabout 8 seconds.

The LOC display will reappear when DISPLAY is pressed, andwhen you hold down this button, it will go out to show the childlock is cancelled.

IMPORTANTYou can lock the VCR with the power off, even if the VCRis standing by for a programmed recording. If you lock theVCR with no cassette in it, the VCR will not accept acassette.

REW FFREC SPEEDSP/EP

Advanced Features

21 3

54 6

87 9

0

VCRTV

44

Remote Control

VCR POWERTurns the VCR on or off. If you have programmedthe VCR to record, you need to turn the VCR off.

EJECTEjects a tape.

CHANNEL Up and DownSelects next higher or lower channel in the VCR’sor TV’s channel memory.

VOLUME Up and DownRaises and lowers the sound of the TV.(Operates the TV only)TV POWERTurns the TV on or off. You need to program yourremote to operate your particular brand of television.

MUTETurns off the TV sound. Press again to restore theTV sound to its previous volume. (Operates the TVonly)

Number keysSelects TV stations.Sets quick search (CM skip) time.

QUICK PROGRAMGoes to Program to record menu.Exits the programming screen.INPUTSelect between the antenna and any other videoequipment that may be connected.

PLAY Plays a tape.

21 3

54 6

87 9

0

CHANNEL

EJECT MUTE

VOLUMEVCR

POWERTV

POWER

CM SKIP

QUICK PROGRAM INPUT

PLAY

STOP

REW FF

DISPLAYPAUSE

X2 REC

INDEX

AUDIO/VIDEO MENU

VCR/TV SP/EP

ADJUST

CANCEL ENTER

ADJUST

VCRTV

STOP Stops a tape.REW Rewinds a tape or reverse searches.FF Fast forwards a tape or fast forward searches.VCR/TV slide switchOperates the VCR when set to the VCR position, theTV when set to the TV position. You need toprogram your remote to operate your particularbrand of television.

RECStarts recording. While recording, adds manualindex mark.

PAUSE Pauses a tape when recording.Freezes a frame when playing a tape.DISPLAYDisplays on the TV screen:• Time elapsed on the tape• Time left on the tape, current time• Channel number and audio reception mode• Audio channel(s) selected• Source supplying the VCR with a signal• If the VCR is stopped, playing, or recordingTurns the Child Lock on and off.

X2Use double speed playback when playing a tape.

INDEX I\\\\\, ^IBegins index search forward and backward.Controls the playback speed of a tape.

AUDIO/VIDEOSelects the audio and video settings to be adjusted.

MENUDisplays the menus. Exits the menus.

CANCELCancels menu selections.Resets the counter display to “0h00m00s.”

ADJUST +, –Selects and adjusts menu selections.

ENTEREnters menu selections.

VCR/TVSwitches between the VCR’s picture and the TV’stuner.SP/EPChanges the recording speed. (SP is standardplay; EP is extended play).

Location of Controls

45

POWER

CHANNEL

REW

STOP PAUSE REC

FF

PLAY

EJECT REC SPEEDSP/EP

REC LENGTH START TIMEOTR2

VIDEO IN L/MONO - AUDIO IN - R

cassette slot

front panel display

remote controlsensor

video input 2 jack

audio input 2 jacks

CHANNELChanges channels.Adjusts tracking and picture vibration.

REW Rewinds a tape or reverse searches.

PLAY Plays a tape.Resumes normal playback from special effects.

FFFast forwards a tape or fast forward searches.

STOPStops a tape.

PAUSE/%%%%%START TIMEPauses a tape when recording.Freezes a frame when playing a tape.Sets the start time in OTR2 recording.

REC/˙REC LENGTHRecords to the end of the tape by pressing once.Sets the recording time for OTR recording bypressing repeatedly.

POWERTurns the VCR on or off.If you have programmed your VCR to record, turnoff your VCR.

EJECTEjects a tape.

REC SPEED SP/EPChanges the recording speed (SP is standardplay; EP is extended play).

video input ˙ jackConnect source here, such as a VCR orcamcorder, to record or dub video.audio input ˙ jackConnect source here, such as a VCR orcamcorder, to record or dub audio.

cassette slotInsert the video cassette tape here.

front panel displaySee the next page.

remote control sensorReceives signals from the remote control.Do not block it.

Front Panel


46

OUTAUDIO

L

R

ANTENNA

OUT

IN

VIDEO

R

L/MONO

OUT

IN 1

IN 1

Rear Panel Jacks

AUDIO INput and OUTput jacksRed and white jacks for receiving (IN) and sending(OUT) audio signals. Red signifies the rightchannel, and white signifies the left channel.Stereo audio cables are also color coded red andwhite. If you are receiving or sending a mono(non-stereo) signal, you should use only the left(white) terminal.VIDEO INput and OUTput jacksYellow jacks for receiving (IN) and sending (OUT)video signals to a monitor TV or from anotherVCR.

ANTENNA IN jackAttach an external antenna or cable to bring in anoutside signal.

ANTENNA OUT jackAttach a coaxial cable to your TV to send outantenna/cable signals from the VCR to your TV.

POWER light : PWR.Is lit when power is ON.

VCR light : VCRIndicates that the picture is controlled by the VCR.

Cassette light : Lights up when a tape is in the VCR.

time displayThis area displays:• current time• OTR and OTR2 timer

VCR

REC

PM

PWR.

Front Panel Display


Record light : RECLights up when the VCR is recording.Flashes when the VCR is in recording pausemode.

Programmed recording light : Lights up when VCR is off and it is programmed torecord.

PM light : PMLights up when the current time or start time ofOTR2 is in the afternoon.Turns off when it is in the morning.

47

Important InformationSpecial Information Concerning Stationary Images or Letterbox Images:

For best performance and longest life, the normal use of a TV should include a mixture of TV picture types.The most frequently used picture types should fill the screen with constantly moving images rather thanstationary images or patterns. Displaying the same stationary patterns over extended periods of time, ordisplaying the same stationary patterns frequently, can cause uneven aging of the TV picture tubes andleave a subtle, but permanent, ghost image. Most TV warranties do not cover this type of damage to thepicture tubes. To avoid this, mix your viewing pattern. Do not show the same stationary image for morethan 15% of your total TV viewing in any one week. Display constantly moving and changing images thatfill the screen whenever possible. We also recommend that you reduce the contrast setting of your TVwhen you watch that type of image. When possible, you may wish to use your television’s PIP, POP,ZOOM, EXPAND or other picture shape controls so that the moving images fill the screen.

Please check your TV’s owner’s guide for other recommendations.

Examples of stationary images include:

• Letterbox top/bottom bars. These are solid colored bars that when showing a widescreen (16:9)image on a standard (4:3) TV.

• Side panels. These are the solid colored side bars when showing standard shaped (4:3) TV images ona widescreen (16:9) TV.

• Stock-market report bars. These include the ticker bar constantly running at the bottom of the TVscreen on financial news channels.

• Shopping channel logos & pricing displays. These include bright graphics that are shown constantlyor repeatedly in the same location.

• Video game patterns and scoreboards.

• Bright station logos. Moving or low-contrast graphics are less likely to cause uneven aging of thepicture tubes.

• On-line (internet) web sites. In addition, any other stationary of repetitive computer style images fromany source may cause uneven aging of the picture tubes.

48

Trouble ChecksIf your VCR malfunctions, try the following steps prior to contacting your Mitsubishi Dealer:

1 Check the Trouble Checks below to see if there is a solution to the current problem that you areexperiencing.

2 If the problem is not addressed on the Trouble Checks, the safety circuits in the VCR may be inoperation, thus please try the following: (the clock setting and the timer recording will be deleted.)

1 If possible, press EJECT on the front panel and remove the tape.

2 Unplug the power cord and leave it unplugged for 3 minutes or more, and plug in again.

3 If a tape is not loaded, press POWER to turn the power on. If a tape is loaded, wait about 1minute until the tape protecting function is completed, then press POWER.

3 You may also try the following procedure if the above steps did not resolve the problem. (Allsettings will be reset to the default settings.)

1 Press POWER on the front panel continuously for about 8 seconds until the current time displayon the front panel shows “- : - -”.

2 If a tape is not loaded, press POWER to turn the power on. If a tape is loaded, the tapeprotecting function will work and “99” will appear on the front panel display to begin count down.Wait about 1 minute until it reaches “00” to show the tape protecting function is completed, thenpress POWER.

If the problem with your VCR persists, contact your Mitsubishi dealer for assistance.

Problem

The VCR won’t turn on.

The VCR power is on but nocontrols work.

You can’t see the VCR’s pictureon your TV.

Poor picture when watching theVCR’s tuner on your TV.

VCR REC button doesn’tfunction.

No picture during recording.

VCR does not record TVprogram.

Try This...

• Check the power cord and the AC outlet.• Is the child lock in use? If so, press and hold DISPLAY on the remote

for more than 8 seconds until the LOC display turns off.

• Is the child lock in use? If so, press and hold DISPLAY on the remotefor more than 8 seconds until the LOC display turns off.

• Set the VCR/TV slide switch to VCR position.

• Check the TV’s input setting.• Check to see that your VCR is not set to External L1 or External L2.

• Check to see if your TV is set to the correct channel or input.• Check your TV’s fine tuning, if using an older TV.• Check your connections to make sure they are secure.

• Check the erasure prevention tab on the tape cassette.

• Check the hook-up.• Check to see if your TV is set to the correct channel or input.

• Check the VCR tuning.• Check the input selection on the VCR. Does the channel display on

the TV screen show External L1 or External L2? If so, switch it totuner by pressing INPUT.

49

Try This...• Check that the programmed recording light lights up in the front panel

display.• Check the clock time.• Make sure you have turned the VCR off before the start time.

• Check the tracking control. Adjust manually if necessary.

• Check the monitor settings.• Check the quality of the video tape.

• Clean the video heads using a dry-type video head cleaning cassette.Do not use a wet-type cleaning cassette, as it may damage yourVCR. Excessive use of a cleaning cassette could shorten head life.Follow the cleaning instructions carefully.

• Have the VCR video heads cleaned by a qualified service technician.

• Check that VCR operational setting is set to VCR-A.• Check to see that the VCR/TV slide switch is set to the correct

position.• Change the batteries.

• In order to protect your tapes and the VCR heads, the FastForwarding/Rewinding Speed will be slower than 500x under thefollowing conditions:1 Use of tapes shorter in length than T-120 (for example, T-30, T-60,

T-90).2 Activating fast forwarding or rewinding from the middle of the tape.

ProblemThe VCR timer recording doesnot operate.

Noise in the picture anddistorted sound.

Poor or no Hi-Fi sound.

Playback is noisy or “snowy.”

VCR remote does not function.

The fast forwarding/rewindingspeed is slow.

Trouble Checks

50

FORMAT VHS NTSC standard with Hi-Fi audioVIDEO SIGNAL SYSTEM EIA standard; NTSC colorRECORD/PLAYBACK SYSTEM Video -- 4 heads

Audio -- 2 Hi-Fi channels and 1 monaural audio controlANTENNA 75-ohm external VHF/UHF combined antenna terminalTUNER 181 channels capability

VHF -- Channels 2 - 13UHF -- Channels 14 - 69CATV -- Channels 1-125

HORIZONTAL RESOLUTION more than 220 lines (SP)more than 210 lines (EP)

SIGNAL-TO-NOISE RATIO more than 45 dB (SP)more than 46 dB (EP)

TIMER PROGRAM CAPACITY 1-month programmable/8 programsMEMORY BACKUP TIME approx. 3 minutesMAXIMUM RECORDING TIME 120 min. with T-120 video cassette (SP)

360 min. with T-120 video cassette (EP)REWIND TIME approx. 43 seconds for T-120 cassette (full recorded tape)POWER REQUIREMENT 120V AC, 60 HzPOWER CONSUMPTION 20 Watts -- 3.0 Watts standbyDIMENSIONS 3.7 in Height x 16.7 in Width x 11.9 in Depth (93 mm x 425 mm x 302 mm)WEIGHT 8.0 lbs approx. (3.6 kg)SUPPLIED ACCESSORIES 1 set coaxial cable

1 remote control2 “AA” size batteries1 registration card

Aadding channels .................... 14adjust button ......................... 44adjusting tracking .................. 33advanced options .................. 42

playback controls .............. 32antenna, connecting ................ 5

jacks ............................. 5, 46audio

connecting a TV with inputs 7input, output jacks ............. 46monitor.............................. 21

audio video functions button ................................ 44 selecting ............................ 23

using ................................. 21auto clock function ................ 15auto power save .................... 39auto speed programming ...... 28

Bbackup, memory ................... 29batteries, installing ................ 10

Ccable, connections to .............. 5cable box, connections to ... 5, 6cancel button........................ 44cancel

button................................ 44programmed recording ..... 29recording in progress ........ 25

cassettelight ................................... 46slot ................................... 45

changing recording settings ..29changing settings while programming .................. 26

channel(s)adding and deleting .......... 14button ......................... 44, 45memorize .......................... 13selecting ........................... 14

child lock ............................... 43choosing a hookup .................. 4clock setting .......................... 15CM skip ................................. 34connections to

antennas ............................ 5cable with or without box 5, 6home theater receiver ......... 8TV w/audio video inputs ... 7

copying a tape ................. 30, 31counter display ...................... 34counter zero stop ............ 22, 35customize choices menu ....... 39

Specifications

Index

51

Ddaylight savings time ............. 16deleting channels ..................14display button ....................... 44displaying current time .......... 38displaying remaining time ..... 38displaying time gauge ........... 38

Eediting features ..................... 30eject button .................... 44, 45enter button ......................... 44erasure, preventing tape .......18

Ffast forward button .......... 44, 45fast forwarding a tape ..... 11, 35front panel buttons ............... 45front panel display ........... 45, 46

Hhead cleaning ........................ 49

Iimportant safeguards ............ 2index

buttons ............................. 44techniques ........................ 36

input button ...........................44

Llanguage, on-screen ............. 12loading a tape ....................... 10location of controls ................44lock VCR ............................... 43

Mmemory backup .................... 29menu button .......................... 44menus, using .........................12mute button .......................... 44

Nnumber buttons ................... 44normal recording ................... 22

Oone touch recording (OTR) ... 19one touch recording, standby 20

Ppause button .................. 44, 45pausing a tape ...................... 11PerfecTape® ................... 22, 40PerfecTape Select ................. 22play button ..................... 44, 45play a tape ............................ 10playback controls, advanced . 32PM light ................................. 46power

button .......................... 44, 45light ................................... 46

program caution .................... 28programmed recording light . 46programming

auto speed ........................ 28cancel ......................... 25, 29changing settings while .... 26

Qquick program button ............ 44quick program ....................... 26quick search .......................... 34

Rrear panel jacks ..................... 46REC button ..................... 44, 45record cancel ........................ 29record light ............................ 46rec speed button ................... 45recording

canceling programmed ..... 29canceling one in progress. 25conventional VCR timer .... 24current broadcast .............. 18one-touch.......................... 19Quick Program .................. 26Standby one-touch ........... 20timer .................................. 24

remote control buttons .......... 44sensor ............................... 45

rental xpress ......................... 41repeat playback ............... 22, 37REW button ................... 44, 45rewinding a tape .............. 11, 35RF converter setting ............. 40

SSAP broadcast ...................... 21search techniques ................ ␣ 34search to blank ............... ␣ 23, 37setting the clock .................... 15skipping programs ........... 28, 29special effects ..................... 32SP/EP button ...................... 44still adjustment .................... 32stop button ..................... 44, 45

Ttape function ......................... 22tape

copying ....................... 30, 31loading .............................. 10playing .............................. 10repeating ..................... 22, 37

television, connecting .............. 7operating with remote ....... 42

timecounter .............................. 34display .............................. 46display current .................. 38gauge ................................ 38remaining .......................... 38

timer recording ...................... 24tracking ................................. 33trouble checks ...................... 48TV POWER button ............... 44

VVCR

light .................................. 46setting up .......................... 12

VCR POWER button ............ 44VCR/TV button ..................... 44VCR/TV slide switch ............ 44video

input, output jacks ............ 46mute ................................. 39

volume button ...................... 44

XX2 button ............................... 44

Index

MITSUBISHIVIDEO CASSETTE RECORDER

LIMITED WARRANTYMITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (MDEA) warrants to the original purchaser of this videocassette recorder if purchased from an authorized MITSUBISHI Audio/Video Dealer that, should it prove defec-tive by reason of improper workmanship and/or material:

a. Parts. For one year from the date of original purchase at retail, we will repair or replace, at our option, anydefective part including the video head without charge for the part. Parts used for replacement are war-ranted for the remainder of the original warranty period.

b. Labor. For ninety days from the date of original purchase at retail, we will provide the labor for a warrantyrepair without charge at an authorized MITSUBISHI service center.

c. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of anydefect within the applicable warranty time period.

1 TO OBTAIN WARRANTY SERVICE, deliver your VCR to the nearest MITSUBISHI service center.Shipping expenses are your responsibility. The name and address of the nearest service center can beobtained from your MITSUBISHI Dealer, or by writing or calling MDEA at the address and telephone numberbelow. Proof of purchase date from an authorized MITSUBISHI Dealer is required when requesting warrantyservice. Present your sales receipt or other document which establishes proof and date of purchase. THERETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDITION OF WARRANTY COVERAGE.However, please detach and return the Owner Registration Card so that we can contact you should a ques-tion of safety arise which could affect you.

2 THIS WARRANTY DOES NOT COVER damage caused by: modification, alteration, repair or service of thisproduct by anyone other than an authorized MITSUBISHI service center; physical abuse to, or misuse of, theVCR; operation in a manner contrary to the instructions which accompany the VCR; freight damage; or anydamage caused by acts of God such as lightning or fluctuation in electrical power. This warranty alsoexcludes all costs arising from installation, adjustment of user controls, external antenna systems, service ofproducts purchased or serviced outside the U.S.A., initial technical adjustments (set-up) and user-requiredmaintenance including head cleaning. Consult the operating instructions enclosed with the product for infor-mation regarding user controls.

3 ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THISPROVISION, MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED ANDDISCLAIMED. THE IMPLIED WARRANTIES OF MERCHANT-ABILITY AND OF FITNESS FOR ANY PAR-TICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF ONE YEAR.

4 UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSONFOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OFBREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE.

5 Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation ofincidental, special, or consequential damages, so the above limitations or exclusions may not apply to you.

6 This warranty gives you specific legal rights and you may also have other rights which vary from state tostate.

7 BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation andcorrect customer control adjustment. If the problem persists, contact your nearest MITSUBISHI Dealer forname(s) of authorized MITSUBISHI Service Center(s). If you are unable to obtain the information, please call1-800-332-2119, or write us at the address below.

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.

9351 Jeronimo Road

Irvine, CA 92618-1904

Warranty

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.9351 Jeronimo RoadIrvine, CA 92618-1904www.mitsubishi-tv.com

© 2003 Mitsubishi Digital Electronics America, Inc.

For your nearest Mitsubishi Authorized Service Centercall 1-800-332-2119

RETAIN THIS PORTION FOR YOUR RECORDS SERIAL NO.

CUSTOMER NAME

STREET ADDRESS

CITY STATE ZIP

PHONE ( ) PURCHASE DATE / /

MO DAY YR

PLACE OF PURCHASE

PHONE ( )

video cassette recorder ownerõs guide · pdf filevideo cassette recorder ownerõs...

Documents