vibe slr 12 active enclosure instruction manual

INSTRUCTIONMANUAL

Slick SLR 12 ActiveSubwoofer EnclosureModels: SLR12A LIMITED EDITION

To ensure maximum performance and safety,

please follow this manual. Please retain the manual for future reference after

installation

OWNERS MANUALCongratulations on purchasing your VIBE SLR subwoofer enclosure, please read this manual in order to fully understand how to get the best results from this w and ensure that all advice on how to look after the subwoofer is followed.

Thank you for buying VIBE, we hope you enjoy listening to your product as much as we enjoyed creating it.

VIBE R&D Division

WARNINGDO NOT EXPOSE THIS PRODUCT TO DAMP OR MOISTURE - doing so may result in fi re, shock or damage to the product.

BEFORE WIRING DISCONNECT THE CABLE FROM THE POSITIVE BATTERY TERMINAL - failure to do so may result in electric shock or injury.

ENSURE GOOD AND CORRECT CONNECTIONS - failure to make the correct connections may result in fi re or damage to the product.

KEEP THE VOLUME AT A LEVEL SO YOU CAN STILL HEAR OUTSIDE NOISE - failure to do this may result in an accident. VIBE equipment is capable of producing sound levels that can permanently damage your hearing. VIBE recommends caution when listening at high volume. For safe and enjoyable listening the sound should be comfortable and clear without distortion.

CAUTION• Never connect any speaker lead to the car chassis. This can cause severe damage to your

speaker / car radio / amplifi er. • Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.• Use caution when working near the fuel / hydraulic lines and electrical wiring. • Observe the correct polarity when wiring, improper phasing may cause a loss of bass

response.• Ensure that no moving parts catch on the speaker or grill (e.g. window or door handles, or

window glass inside the door)

INSTALLATION• The quality of the installation will affect the system performance and reliability.• Contact your nearest authorised VIBE dealer if you are unsure about the installation of this

product.• Please mount this unit away from any potential hazards.• Minimising the length of wires will provide higher audio output from the system.• The speaker should be securely fastened to the mounting position using the screws pro-

vided.• Pre drill your mounting holes using a drill and position with the template provided.• Be sure to investigate your mounting area thoroughly for electrical wires, brake or fuel lines

or fuel tank to prevent causing any damage.

BLE Fock or inju

ONNECTIONS -roduct.

EL SO YOU CAN STILLident. V ent is ca

your he ommendable listening the sound should be

peaker lead to the car chassis. This can cause s/ amplifi

cutting any holes, investigate the layout of your vehicleen working near the fuel / hydraulic lines and electrical wir

orrect polarity when wiring, improper phasing may cause a lo

t no moving parts catch on the speaker or grill (e.g. window or doorlass ins

ALLATquality of the installation will affect the system performance and reliability.

ntact yo llation ofproduct.Please mount this unit away from any potential hazards.Minimising the length of wires will provide higher audio output from the system.

the systemdealer if yo

E equipmng. VIBE r

g the sound

car chass

stigate th/ hydrau, improp

spea

Slick SLR 12 Active Limited Edition Subwoofer Enclosure

2

RUN IN PROCEDUREVIBE recommends that you follow the run in procedure for the subwoofer detailed below.

When your subwoofer is used for the fi rst time naturally like most brand new items it is very stiff and rigid, it will take time for the moving parts of this subwoofer to loosen up before it will be ready to deliver its full potential.

For the fi rst 30 hours it is recommended that you play the subwoofer initially at low to medium volumes, gradually increasing the volume level as time progresses. As a guide, if you listen to it for 1 hour every day it will take a month for the speaker to run in properly. You will notice a big change in the sound of the subwoofer over this period, as the spider and surround begin to run in the sound will get deeper and punchier, also the output of it will increase as the suspension loosens up.

A new subwoofer is like a new car engine, it needs a few thousand miles before you can drive it to its full potential, driving it into the ‘red line’ from the fi rst day will mean engine damage is certain and will not be covered by warranty and the same applies to the subwoofer. Failure to follow this simple procedure is the most common reason for a subwoofer to fail after a very short period of time.

INSTALLATIONThe most common place to mount a bass enclosure is in the luggage compartment of the vehicle. Where in the luggage compartment it is mounted will have an effect on the sound produced allowing the user to tailor the sound to best suit their musical tastes. For example if the enclosure is mounted facing the rear bumper, the bass produced will be noticeably deeper than if it is fi red into the rear seat.

Do not be afraid to experiment with positioning as a little time and effort can yield great improvements in sound.


3

ACTIVE ENCLOSURE INSTALLATIONYour VIBE SLR enclosure is designed with a swift installation routine in mind. Please mount the enclosure in a dry location on a solid surface. NEVER mount the enclosure upside down, this will cause the amplifi er to overheat and will eventually damage the amplifi er. Before fi xing the enclosure in place please ensure that there is suffi cient air fl ow around the amplifi er heatsink, at least two inches will be suffi cient.

POWER CABLE• At least a 10 gauge cable should be used for both the power and the ground connections to

the amplifi er.• The power cable should be taken directly from the battery. Rubber grommets should be used

when passing through any bulkheads to prevent the cable from becoming chaffed or cut.• It is vital that a fuse / circuit breaker (of at least equal value to the one fi tted on the amplifi er)

is placed in line with the power cable and is no further than eighteen inches away from the battery.

• Please ensure that the fuse is not fi tted until the entire installation procedure is complete.• The two tables below are to help you decide on what cable is correct for you. The fi rst ena-

bles you to select the size of cable depending on the length required. The second will help you convert the cable size from American Wire Gauge to Metric if you need to.

Length of RunCurrent demand 0 – 4 Ft 4 – 7 Ft 7 – 10 Ft 10 – 13 Ft 13 – 16 Ft 16 – 19 Ft 19 – 22 Ft 22 – 28 Ft0–20 amps 14 12 12 10 10 8 8 820–35 amps 12 10 8 8 6 6 6 435–50 amps 10 8 8 6 4 4 4 450–65 amps 8 8 6 4 4 4 4 265–85 amps 6 6 4 4 2 2 2 085–105 amps 6 6 4 2 2 2 2 0105–125 amps 4 4 4 2 0 0 0 0125–150 amps 2 2 2 0 0 0 0 0

AWGAA to Metric Conversion Chartcross sectional area

AWGAA Number Inch mm mm2

0 0.325 8.25 53.51 0.289 7.35 42.42 0.258 6.54 33.63 0.229 5.83 26.74 0.204 5.19 21.15 0.182 4.62 16.86 0.162 4.11 13.37 0.144 3.66 10.58 0.128 3.26 8.369 0.114 2.91 6.6310 0.102 2.59 5.26

1 M e t r e – 3 . 2 8 F e e t

4


GROUND CABLE• The ground cable needs to carry the same current as the power cable. At least a 10 gauge

cable should be used.• The amplifi er ground should be connected directly to the chassis of the vehicle, to bare

metal.• The cable length should be kept to an absolute minimum. It is not recommended that you

connect the ground cable to the vehicle’s seatbelt anchor point.

REMOTE TURN ON• A minimum of 18 gauge cable should be used for this connection.• The cable should be run with exactly the same care and attention as the power cable and

taken back to the source (headunit) and joined to the remote cable provided.• If the source (headunit) does not have a remote turn on cable then a 12v supply should be

used. This will require a switch to be fi tted inline to enable the amplifi er to be turned on and off. Remember that if this switch is left on you will fl atten the car battery.

RCA CABLES• Please take extra care when running these cables from the source to the amplifi er. Ensure

that they are placed away from all items that can generate any interference, wiring har-nesses etc.

• It is recommended that the RCA cables should be run on the opposite site of the car to any previously installed power cables, if possible.

INPUT CONNECTIONS

BATTERY

FUSEConnect tochassis / groundof vehicle

Connect to remote turn-onlead of source unit

SOURCE (HEAD UNIT)

5


AMPLIFIER CONNECTIONS & CONTROLS

A. LOW LEVEL INPUTLow level input for connection to any source (headunit) with a low level output. This is your RCA output from the source (headunit).B. HIGH LEVEL INPUTTo be used when no RCA’s are available. Use the provided loom to connect to the closest speakers.C. GAIN CONTROLUsed to match the input signal of the source (headunit) to the amplifi er. See the setup section for more details.D. CROSS OVER FREQUENCY CONTROLHigh pass frequency control. The frequency ranges from 50hz to 250 Hz.E. BASS BOOST CONTROLTo provide up to an extra +6 dB of bass boost at 45 Hz. Use this boost to increase bass output from the amplifi er.F. FUSEPlease ensure the following fuse rating is used when replacing fuses:SLICK SLR12A (25 amp)G. POWER CONNECTIONSPower connections. See input connections section for details on correct connections.H. POWER PROTECT LIGHTWhen the amplifi er is operating correctly the light will illuminate constant ‘white’. When the amplifi er is in power protecttion mode the light will illuminate ‘red’.

H

AE BCF DG

6


SET UP SECTIONTo correctly set the gain control of the amplifi er to match that of the source (headunit) use the following setup routine:

• Turn the gain control to minimum on the amplifi er.• Ensure the bass boost is set to 0 dB.• On the headunit set all crossovers to fl at and both bass and treble to zero.• Turn up the source (headunit) to approx 3/4 volume.• Very slowly turn up the gain on the amplifi er until distortion can be heard in any of the speak-

ers or until the volume reaches an uncomfortable listening level when this is reached turn down the gain control slightly.

• The gain control is now set.

The setting of the crossover will directly effect the sound you will hear from the subwoofer. At its lowest setting (50 Hz) the subwoofer will only react to frequencies from around 35 Hz to 50 Hz. At its highest setting (250 Hz) the subwoofer will react to a larger range of frequencies from around 35 Hz to 250 Hz. Experiment with this setting to achieve a sound you are happy with that feels comfortable with the music that you listen to.

7


TROUBLESHOOTINGBefore removing the amplifi er, refer to the list below and follow the suggested procedure. Always test the speakers and confi rm that they are wired correctly fi rst. If in any doubt get help from a qualifi ed auto electrician.

AMPLIFIER WILL NOT POWER UP• Check for good ground connections. Ensure that the ground cable is connected directly to

bare metal and not a painted surface.• Using a multimeter check the that remote terminal has at least 7V DC.• Using a multimeter check that there is battery voltage on the positive terminal.• Check all fuses.• Check that the protection light is not illuminated. If it is lit, shut off the amplifi er for thirty

seconds and then turn it back on.

PROTECTION LED ILLUMINATES WHEN AMPLIFIER IS POWERED UP• The amplifi er is designed to shut down automatically when the units temperature goes above

80 degrees. If the amplifi er feels very hot then this may be the reason for the amplifi er not starting.

• Check that there is good airfl ow around the amplifi er. In some applications an external fan may be required.

BLOWN FUSE(S)• Check both positive supply and ground for shorts.• Check that the positive wire is connected to the positive terminal on the amplifi er.• Check that the negative wire is connected to the ground terminal on the amplifi er.• Ensure that the correct rated fuse is fi tted:

SLICK SLR12A (25 amp)

DISTORTED SOUND• Check the gain control is not set at too high a level. If the sound is distorted turn the down

the gain until the sound is clear.• Check that all crossover frequencies are correct. See Setup section for more details.• Check that the ground cable is making good contact with the vehicle chassis.• Check the the RCA cables are making good connection with the source and amplifi er.

8


LIMITED WARRANTYAll VIBE products carry a full 12 months warranty, valid from the date of the original receipt and proof of purchase. In order to validate this warranty, the warranty card should be returned to VIBE within seven days of the original purchase date. The original receipt and packaging are should also be retained for this twelve month period. If at any stage during the warranty period you have a problem with the product then it should be returned to the point of purchase, in its original packaging, complete with no items missing. If the store is unable to fi x the product it may have to be returned to VIBE this process takes around 7 working days and no costs will be occurred.

A full description of VIBE’s warranty information can be found on our website:WWW.VIBEAUDIO.CO.UK/WARRANTY

WHAT IS NOT COVERED● Damage to product due to improper installation● Subsequent damage to other components● Damage caused by exposure to moisture, excessive heat, chemical cleaners and/or UV

radiation● Damage through negligence, misuse, accident or abuse, repeated returns for the same fault

may be considered abuse● Any cost or expense related to the cost of removal or re-installation of the product● Damage caused by amplifi er clipping or distortion● Items repaired or modifi ed by any unauthorized repair facility● Return shipping on non defective items● Products returned without a returns authorization number● Damage to product due to the use of sealant

INTERNATIONAL WARRANTYContact your International VIBE audio dealer or distributor concerning specifi c procedures for your country’s warranty policies.

WARNINGVibe subwoofers are capable of sound pressure levels that can cause permanent damage to your hearing and those around you. Please use common sense when listening to your car audio system and practice safe sound.

COPYRIGHTAll content included in this manual such as text, graphics, logos, icons, images and data, are the property of VIBE Technologies Limited (herein referred to as “VIBE”, “us” or “we”) and its affi liate or their content and technology providers, and are protected by United Kingdom and International copyright laws. All rights reserved. VIBE Turbo Port, Vibe TurboVent, Pressure Board, Super Driver, VIBE Pulse, VIBE Power, VIBE Digital, VIBE MAG Plugs, Ferrite Loaded, VIBE Solid Core, VIBE OCC, VIBE FLAT, BlackAir, BlackBox, Space, MonoBox, SA-K, SR, QB69, ICC, Bass Enhance, Bass Enhance+, QBass, SpeedBass, PowerBass and all stylised representations of product names, or the abbreviations of product names, as logos are all trademarks of VIBE. Graphics and logos are trademarks or trade dress of VIBE Technologies Ltd or its subsidiaries. VIBE’s trademarks and trade dress may not be used in connection with any product or service that is not VIBE’s, in any manner that is likely to cause confusion among customers or in any manner that disparages or discredits VIBE. All other trademarks not owned by VIBE or its subsidiaries that appear in this manual are the property of their respective owners, who may or may not be affi liated with, connected to, or sponsored by VIBE or its subsidiaries.

TO THE FULLEST EXTENT PERMITTED AT LAW, VIBE IS PROVIDING THIS MANUAL AND ITS CONTENT ON AN “AS IS” BASIS AND MAKES NO (AND EXPRESSLY DISCLAIMS ALL) REPRESENTATIONS OR WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WITH RESPECT TO THIS MANUAL OR THE INFORMATION, CONTENT, MATERIALS OR PRODUCTS INCLUDED IN THIS MANUAL INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN ADDITION, VIBE DOES NOT REPRESENT OR WARRANT THAT THE INFORMATION CONTAINED IN THIS MANUAL IS COMPLETE OR CURRENT, AND THAT ALL SPECIFICATIONS AND INFORMATION CONTAINED WITHIN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. VIBE RECOMMEND CAUTION WHEN LISTENING TO MUSIC REPRODUCED THROUGH VIBE EQUIPMENT. VIBE EQUIPMENT IS CAPABLE OF PRODUCING SOUND AND SOUND PRESSURE LEVELS THAT CAN PERMANENTLY DAMAGE HEARING OF YOU AND THAT OF OTHERS. FOR SAFE AND ENJOYABLE LISTENING, THE SOUND SHOULD BE CLEAR WITHOUT DISTORTION AT A COMFORTABLE VOLUME. BY USING ANY VIBE EQUIPMENT, YOU AGREE TO TAKE FULL RESPONSIBILITY FOR YOUR OWN SAFETY AND THE SAFETY OF OTHERS WHEN LISTENING TO MUSIC AT HIGH VOLUMES THROUGH EQUIPMENT YOU HAVE PURCHASED. USE OF ANY VIBE EQUIPMENT CONSTITUTES AGREEMENT TO THIS DISCLAIMER.

Except as specifi cally stated in this manual, to the fullest extent permitted at law, neither VIBE nor any of its affi liates, directors, employees or other representatives will be liable for damages arising out of or in connection with the use of this manual or the information, content, materials or products included. This is a comprehensive limitation of liability that applies to all damages of any kind, including (without limitation) compensatory, direct, indirect or consequential damages, loss of data, income or profi t, loss of or damage to property and claims of third parties. For the avoidance of doubt, VIBE does not limit its liability for death or personal injury to the extent only that it arises as a result of negligence of VIBE, its affi liates, directors, employees or other representatives.

9


KE

EP

IT

SA

FE

Sta

ple

you

r re

ceip

t he

re:

MODEL NUMBER:

SERIAL NUMBER:

PURCHASED FROM:

DATE OF PURCHASE:

In order to protect your purchase and aid your warranty please fi ll in the following form and keep it safe for your future reference.

For more information and to register your warranty online, visit:www.vibeaudio.co.uk/warranty

10

SPECIFICATIONS

RMS Power Peak Power

SLICK SLR12A 400 Watts 1200 Watts


twitter.com/vibeaudio youtube.com/vibeaudio

vibe slr 12 active enclosure instruction manual

Documents

vibe equipment

vibe rg

fuel lines

electrical wiring

electrical wires

fuel hydraulic lines

system performance

mounting holes