venice wall hung vanity unit › assets › products › 400000 › 1862017 › ...venice wall hung...

VENICE WALL HUNG VANITY UNIT

Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.

Tech Page Version 1

SPECIFICATIONSRecommended Use Domestic, Hotel and Commercial

Material Exterior: Timber laminate on HMR board, Thermofoil on HMR board

Colour Arlington Oak, Mali Wenge

Bench Top Colours Arlington Oak, Mali Wenge, Caesarstone® Snow™

Fixing Bolted/screwed to wall by licensed trades personSupplied with easy to install brackets that must be fitted to the unit.Installer to determine appropriate wall fixings

Basin Sold separately

Tap Hole Availability No

Drawers Blum push to open drawersIncludes drawer divider

Micro Trap Supplied with 40mm pvc micro trap

To see the complete OMVIVO range go to www.reece.com.au/bathrooms

The Venice Collection balances modern symmetry and classical beauty. Embodying organic design and finishes, flowing form and function with timeless style. Venice is contemporary luxury and is designed to be paired with the Venice basins and box frame mirror.Designed and manufactured in Australia.

VARIATIONS 750 1000 1200 1500 DoubleWidth mm 750 1000 1200 1500

Depth mm 550 550 550 550

Height mm (Excluding Basin) 410 410 410 410

Number of drawers 1 1 1 2

page 1 of 9


CABINET OPTIONS

BENCH TOP OPTIONS

Arlington oak White satinMali wenge

CLEANING RECOMMENDATIONS

Your furniture should be cleaned with a mild, non-acidic, non-abrasive detergent and soft cloth. Finish by cleaning off detergents with a soft slightly damp cloth and towel dry. Always clean spills and water immediately.It is important that the cleaning instructions for your solid surface basin are not carried out on the vanity as this will scratch the finish.

Damage caused by any improper treatment is not covered by the product warranty – refer to Warranty Conditions.

Arlington oak Caesarstone™ Snow®Mali wenge

page 2 of 9


LINE DRAWINGS

CABINETS

750 Cabinet

1200 Cabinet

550 750

410

1000 Cabinet

5501000

410

550

1200

410

1500 Double Drawer Cabinet

550

1500

410

ASSEMBLY LIST

550 750

410

Cabinet with drawer runners

40MM ELBOW SEAL

1/2” NUT

40MM MICRO TRAPLOOSE NUT BODY

40MM TAPER SEAL

40MM CUSTOM NUT

40mm pvc trap Brackets Internal drawer divider

Note: Venice 750, 1000 and 1200 = 1 x set of brackets

= 1 x internal drawer dividerVenice 1500 double = 2 x sets of brackets

= 2 x internal drawer divider

page 3 of 9


VENICE BASIN CONFIGURATIONS

VENICE 450 BASIN POSITION CONFIGURATION OPTIONS FOR CABINETS

VENICE 700 BASIN POSITION CONFIGURATION OPTIONS FOR CABINETS

OTHER SUITABLE BASINS FOR VENICE CABINETS AND POSTION CONFIGURATION OPTIONS

BASINS VENICE 750TapHole Centre Bowl

VENICE 1000Offset Bowl

VENICE 1000Centre Bowl


VENICE 1200Centre Bowl

VENICE 1200Double Bowl


VENICE 1500Double Bowl

Living SQ 360 0TH Yes Yes Yes Yes Yes Yes Yes Yes

Living SQ 600 0TH Yes No Yes No Yes No Yes Yes

Alape Unisono 325 0TH Yes Yes Yes Yes Yes Yes Yes Yes



Alessi One drop in 500* 0TH/1TH Yes Yes Yes Yes Yes Yes Yes Yes

Alessi One counter 750* 1TH No No Yes No Yes No No No

Palomba counter 510 1TH Yes Yes Yes Yes Yes Yes Yes Yes

Palomba counter 850 0TH No No Yes No Yes No No No

Palmoba drop in 850* 0TH No No Yes No Yes No No No

Palomba counter 900 0TH No Yes No Yes No No Yes No

*Basins with a star will be supplied with a cut out in the drawer of the cabinet for plumbing.1TH : Basin has 1 tap hole.0TH: Basin does not have a tap hole, taps must be wall mounted.

Centred bowl750/1000/1200(Single drawer)

Offset left or right bowl1000/1200 (Single drawer)1500 (Double drawer)

Double bowl1200 (Single drawer) / 1500 (Double drawer)

Centred bowl750/1000/1200(Single drawer)

Offset left or right bowl1500 (Double drawer)

Double bowl1500 (Double drawer)

page 4 of 9


VENICE CABINET INSTALLATION INSTRUCTIONS

NO claims for damages / defects will be recognised after installation.

Prior to installation it is important to unpack and inspect your products to ensure no damage has occurred in transit and that the product IS CORRECT.If damage has occurred, or a visible defect exists, do not proceed with installation and contact supplier IMMEDIATELY.

If the wall the cabinet is being installed on is not square the cabinet may twist and drawers may not work efficiently. Use packers to ensure cabinet is square if wall is not square.

Venice cabinets are not designed to be positioned in a corner or flush between two walls. If this is unavoidable, the installer is to determine appropriate distance from adjacent wall.

Read all instructions beforehand. Pay particular attention to locations of plumbing, brackets and measuring up for these.

Step 1. Remove drawer/s from cabinet before installation. a. Squeeze orange handles on locking devices. See figure 1*. b. Pull drawer straight out and up**.

*Drawer component appearance may vary from illustration

**Drawer installation and operation is adjusted and tested before leaving factory. If further adjustment is required after installation it is the responsibility of the installer. Care must be taken when removing and reinstalling drawer to prevent damage to any part of the cabinet.

Step 2. Using appropriate fixings*, secure brackets to wall so they are level and at correct spacing for cabinet. See figure 2.*It is the responsibility of the installer to select appropriate fixing materials.

Figure 1.

A

B

Figure 2.

610mm±5 for 750 cabinet



580mm±5


580mm±5

page 5 of 9


Step 3. Rough in plumbing from wall according to basin configuration ie. Left / right / centre / double Figure 3 shows dimensions of cut outs in each cabinet rear.

See figure 3 - 5 for VENICE 450 & 700 BASIN plumbing locations only.

Important note: For basins other than Venice, the installer MUST refer to individual basin details as these vary according to basin and components such as wastes and microtraps selected. Tapholes are not recommended on timber cabinets as water damage will not be covered by warranty.

Figure 3 cut out centres do not always correspond to plumbing centres.

Ensure that basin and plumbing components are temporarily assembled to cabinet first to determine exact vertical and horizontal plumbing out position at wall.

Also assemble and check drawer clearance to microtrap.

For VENICE 450 & 700 BASIN plumbing locations only, see figure 4 and figure 5.

VENICE BASINS horizontal plumbing positions correspond with centre positions of relevant cut outs shown in figure 3.

Figure 3. Figure 4.

750 Cabinet

305 305

53

308

170

1000 Cabinet

430 430218 218

53

308

170 170 170

Very important for Venice Basins microtrap and plumbing positioning

Caution: 75mm±2mm from top of brackets to centre of outlet at wall

Figure 5.

page 6 of 9


Step 4. With drawer removed, slide cabinet onto brackets into position. Ensure cabinet back is positioned hard against the wall and it is square and level. See figure 6. It is recommended that the vanity be sealed along the edges that meet the wall around the top using a good quality bathroom silicone.

Step 5. Fasten cabinet to brackets on underside of top using fasteners supplied. Fix the bottom corners of the cabinet to the wall at the inside rear of the cabinet. Use additional fixings for support if required.* See figure 7.

* If the wall is not square, packers mush be used to ensure the cabinet does not become twisted. If the wall is not level vertically and horizontally the drawers may not be aligned or operate properly. It is the responsibility of the installer to select appropriate wall fixings.

1200 Cabinet

530 530217 217

53

308

170 170 170

1500 Cabinet

305 305275275

260 260

270

63

Figure 6.

Wall

Figure 7.

Cabinet to wall fixings not supplied.To be determined by installer.

Bracket to wall fixings not supplied.To be determined by installer.

page 7 of 9


VENICE BASIN INSTALLATION NSTRUCTIONS

NO claims for damages / defects will be recognised after installation.

Prior to installation it is important to unpack and inspect your products to ensure no damage has occurred in transit and that the product IS CORRECT.If damage has occurred, or a visible defect exists, do not proceed with installation and contact supplier IMMEDIATELY.

Step 6. Prepare bench top surface and make sure it’s clean and dry. Ensure cut out suits basin. See figure 8. a. Apply a neat generous bead of adhesive silicone sealant around the base flat of basin. See figure 9. b. Immediately place the basin on to the cabinet the right way up with the waste centred over the waste cut out. c. Once plumbing and trap are in position, place waste through the basin. With seals in place, hand-tighten lock nut to secure waste in basin. See figure 10. d. Clean excess silicon around base of basin and leave to dry, following silicone instructions.Note: Bottle trap is not included with basin

Step 7. Replace drawer/s on cabinet*. See figure 11.

Figure 8.

Basin outlineØ100mm waste cutout

Basin outline Ø100mm waste cutout

Figure 8.

Figure 10.

Figure 11.

1

Venice 450 basin

Venice 700 basin

Venice 450 basin Venice 700 basin

page 8 of 9


VENICE CABINET DRAWER ADJUSTMENT INSTRUCTIONS

2

Adjustment

Insert

Side adjustment on both sides viathe locking device ±1.5mm

Balance side adjustment via the right,back runner

Tilt adjustment

Remove

Depth adjustment +2/-1mm

page 9 of 9

venice wall hung vanity unit › assets › products › 400000 › 1862017 › ...venice wall hung...

Documents