valvula esferica criogenica tbv
TRANSCRIPT
-
5/24/2018 Valvula Esferica Criogenica Tbv
1/20
TBVValves
TBV
VALVES & MEASUREME
-
5/24/2018 Valvula Esferica Criogenica Tbv
2/20
VALVES & MEASUREME
CT-TBV-022/12-SWP-3MTBV2
-
5/24/2018 Valvula Esferica Criogenica Tbv
3/20
VALVES & MEASUREME
CT-TBV-022/12-SWP-3M TBV
TBV VALVES
Introduction .......................................................................................... 4
Instrument Valves ................................................................................. 5
Flanged Ball Valves ............................................................................... 7
Three-Piece Ball Valves .......................................................................... 8
Diverter Valves ...................................................................................... 9
Cryogenic Ball Valves ............................................................................ 10
Special Service ...................................................................................... 12
Check Valves ........................................................................................ 13
Instrument Installation Details ............................................................... 14
Instrument and Process Valves .............................................................. 14
Seat Rating Chart .................................................................................. 15How to Order ....................................................................................... 16
Aftermarket Services ............................................................................. 17
Trademark Information ......................................................................... 18
TABLE OF CONTENTS
-
5/24/2018 Valvula Esferica Criogenica Tbv
4/20
VALVES & MEASUREME
CT-TBV-022/12-SWP-3MTBV4
Camerons Valves & Measurement (V&M)group is a leading provider of valves and
measurement systems to the oil and gas industry. The groups products are primarily used to
control, direct and measure the flow of oil and gas as it is moved from individual wellheads
through flow lines, gathering lines and transmission systems to refineries, petrochemical plants
and industrial centers for processing.
The Engineered & Process Valves division provides a wide range of valves for use in natural gas,
LNG, crude oil and refined products transmission lines. The traditional CAMERONfully-welded
ball valve product line has been combined with the GROVE, RING-O, TOM WHEATLEY,
ENTECHand TKproduct lines. This broad offering has significantly strengthened Camerons
ability to serve as a single source for a wide scope of customer requirements. The division also
provides critical service valves for refinery, chemical and petrochemical processing businesses
and for associated storage terminal applications, particularly through the ORBITand GENERAL
VALVE. These brands are complimented by WKMand TBVvalve products and considerably
expand the scope of this divisions product offerings.
TBV valve products are manufactured and assembled at Camerons new facility in Millbury,Massachusetts. The TBV facility offers 100,000 ft2of space of which 80,000 ft2is dedicated to
manufacturing, assembling, testing, shipping, and quality assurance. The increased
manufacturing space has afforded Cameron the opportunity to expand its product offering
and size ranges. TBV is now competitive in the LNG, mining and petrochemical markets with
its ability to offer larger size ranges in its line of products.
Millbury, MA
-
5/24/2018 Valvula Esferica Criogenica Tbv
5/20
CT-TBV-022/12-SWP-3M TBV
VALVES & MEASUREME
TBV VALVES
INSTRUMENT VALVES
Series 4100
The TBV series 4100 is an all welded, double female instrument or process v
which meets API 607 4th Edition fire safe requirements. Standard sizes inclu
1/4 in. - 1 in. (8 mm - 25 mm). Material options include all commercially
available alloys.
Series 41/61
The TBV series 41/61 is an all welded design with one female NPT end and
one male end. The male end is available with screwed, butt weld, socket
weld, and flanged connections. Male and female ends may be different size
upon request.
Series 5500
The TBV series 5500 is a true dual ball block-and-bleed valve used for primar
isolation for both instrumentation and process. There are two closure
members on each side of the bleed valve. For the bleed, a standard TBV
instrument ball valve is recommended. Non-TBV brands can be utilized for th
bleed, such as needle or gate valves, depending on customer preference. Th
series 5500 is available up through 3 and ASME 600 pressure class in any
commercially available material.
Series 6100
The TBV series 6100 is fully rodable and provides three 1/2 female ports wi
one male end for attachment to an orifice flange. The TBV series 6100 allow
for different sized male ends up to 1 in size and is available in a variety
materials. The valve can be installed in pairs on 2 1/8 centers.
Series 61/41/61
The double male end TBV series 61/41/61 valve is a natural offshoot of the T
series 4100 which eliminates the need for nipples to be used with female en
valves. The all welded design reduces the number of leak paths and extende
male ends are available upon request.
-
5/24/2018 Valvula Esferica Criogenica Tbv
6/20
CT-TBV-022/12-SWP-3MTBV6
VALVES & MEASUREME
TBV VALVES
INSTRUMENT VALVES
Series 6400
The TBV series 6400 valve includes all of the advanced TBV ball valve features
in a fire safe design that meets API 607 4th Edition. The TBV series 6400 is
available with a variety of seat materials in a carbon steel or stainless forged
body from 1/2 - 1. Other materials are available upon request. The TBV series
6400 is furnished with one NPT end and allows a choice of NPT, socket weld,
or IREB end connections for the other end. This 1/4 turn ball valve replaces
leaky extended body gate valves in process, block, bleed and drain applications.
Series 6500
The TBV series 6500 cast body process transmitter valve replaces gate valves
with advanced TBV ball valve features in a fire safe design meeting stringentrefinery and chemical plant requirements. The TBV series 6500 features all
welded tamper proof construction, an internal blow-out proof stem and an oval
safety handle to prevent accidental operation. The unique design of the TBV
series 6500 incorporates back-up metal fire lips to provide sealing should the
soft seals sublimate in the event of fire and optional graphoil stem seals
ensuring fire safe protection. TBVs series 6500 offers reliability, safety, visibility,
unique mounting capability, quality and unsurpassed leakage protection.
Series 6800
The TBV series 6800 is an instrument valve with a cast body that incorporates
an integral lockout pad and a high performance stem packing. The valve comes
equipped with a locking oval handle as a standard feature. It is seal welded to
prevent tampering or accidental unthreading when removing from the line.
The TBV series 6800 is fire safe when ordered with appropriate seals, and is fully
rodable. Because of the cast lockout pad, it cannot be turned on 2 1/8 centers.
Series 6900
An instrument valve similar to the TBV series 6100 valve, the TBV series 6900
valve uses a cast body that incorporates an integral lockout pad and a high
performance stem packing. Like the TBV series 6100, the TBV series 6900 is
intended as a gage isolation valve, with tapped NPT side ports for flush and
drain functions. It incorporates all of the other features of the TBV series 6100
valve; rodability, fire safety, and seal welding. The valve comes equipped with a
locking oval handle as a standard feature. Because of the cast lockout pad, it
cannot be turned on 2 1/8 centers.
-
5/24/2018 Valvula Esferica Criogenica Tbv
7/20
CT-TBV-022/12-SWP-3M TBV
VALVES & MEASUREME
TBV VALVES
FLANGED BALL VALVES
Series 2000
The TBV series 2000 is a uniquely designed, reduced port flanged ball valve
offering unlimited versatility with respect to materials, features, and modifie
to satisfy todays sophisticated process valve requirements. Where corrosion
high temperatures, slurries, and flow control applications are to be met, the
TBV series 2000 is a clear choice. The valve body is designed to facilitate eas
automation by including both ISO and flange boss mounting capabilities as
standard. The TBV series 2000 is available in 1/2 - 8, ASME 150, 300.
Valve safety is also addressed by utilizing the standard blow-out proof stem
design in conjunction with optional features such as oval safety handle for si
up to 1 1/2, lock-out device, fugitive emission and bellows seal bonnets. Th
are designed to comply with the fire safe standards of major oil refineries an
API 607. As with all TBV valves, quality, flexibility, long service life, and safet
make this valve the best choice for integrity and application satisfaction.
Series 1800
The TBV series 1800 flanged valve, available in standard or full port design, i
high integrity two-piece design. The leak proof design is enhanced through
use of an optional high performance bonnet which eliminates all possibility o
release of toxic media. The TBV series 1800 also provides a stop plate with
open/closed indication and a tapped actuator mounting plate which allowsactuator installation without disturbing the stem packing. This unique design
allows the valve to be manufactured from bar stock, thereby maintaining
flexibility of manufacture. It is available from 1/2 to 10 in a variety of body
and seat materials with ASME 150 - 1500 flanges.
Series FE2000 and Series FE1800
The TBV series FE2000 and TBV series FE1800 valves incorporate all of the
features of the TBV series 2000 and TBV series 1800 Flange valves, plus the
ability to be used in critical applications where handling of toxic emissions isrequired. The bonnet is welded to the valve body eliminating a potential leak
path, utilizing either double chevron or wedge packing with lantern ring,
optional monitoring, leak off port, and maintenance free-extended cycle life
Finally, our unique live loaded floating stem design preserves the FE seal
integrity even in fire safe applications. The valve is available in 1/2 to 8size
for the TBV series FE2000 and 1/2 to 10 sizes for the TBV series FE1800.FE1800FE2000
-
5/24/2018 Valvula Esferica Criogenica Tbv
8/20
CT-TBV-022/12-SWP-3MTBV8
VALVES & MEASUREME
TBV VALVES
FLANGED BALL VALVES
Series 2800
The TBV series 2800 two-piece, cast full port flanged ball valve is specifically
designed to tackle severe service applications. This design includes a Live
Loadeddual stem seal (primary and secondary seal) as standard. The body and
bonnet are cast as a single piece with no welds or crevices. The TBV series 2800
is available from 1 to 8 with ASME 150 - 300 flanges (3- 8 ASME 600
available). Materials include cast stainless steel, monel, hastelloy, alloy 20, nickel
and others as required.
Series 3300
An enhanced version of the TBV series 1800, the TBV series 3300 is suited for
highly corrosive and erosive applications. Design includes a secureddownstream seat, spring loaded upstream seat and enhanced ball / stem
engagement. This valve is manufactured from barstock from any commercially
available material. It is available from 1 to 14 ASME 150 - 1500.
Series 1100
Along with all of the features and versatility of a three-piece valve, the TBV
series 1100 valve incorporates a raised face on the seat bearing side of the
endplate which assures positive alignment of the components and positive
preset. The body seal is 100% enclosed, extending the temperature range of
virgin TFE. Rugged construction features a heavy duty handle and stop plate,
and oversize body bolts with a variety of material options. The TBV series 1100
is 1500 WOG rated and is available in a wide variety of materials with NPT,
socket weld, butt weld, and flanged end connections in 1/4 through 10
sizes. Other special end connections are available upon request.
Series 3100
The TBV series 3100 wafer three-piece valve combines the benefits of a
standard three piece with additional wafer features. The three-piece design
utilizes raised face end plates to ensure correct alignment with the body, totally
encapsulated body seals, and a bottom entry blow-out proof stem. The wafer
configuration provides additional benefits, including reduction of the material
mass of the valve and lower cost. The TBV series 3100 can be used between
ASME 150 - 600 flanges with a 1500 psi pressure rating and is available from
1/2 - 8 in a wide variety of alloys.
THREE-PIECE BALL VALVES
-
5/24/2018 Valvula Esferica Criogenica Tbv
9/20
CT-TBV-022/12-SWP-3M TBV
VALVES & MEASUREME
TBV VALVES
DIVERTER VALVES
Series 5100 (fabricated from a Series 1100)
TBV offers the series 5100 Diverter valve to accomplish what would otherwi
require two or more two-way valves. The diverter valve utilizes all of the
benefits of the two-way, three-piece TBV valve: a blow-out proof stem, raise
face end plates to eliminate radial piping stresses that could cause body seal
leakage, a wide variety of seals, and a large selection of end connections. Th
TBV series 5100 is also available in either a diverter or a three-way format w
bottom or side porting, and for 90 or 180 operation, from 1/4 through 6
making it valuable for a multitude of applications.
Four-Way
TBVs Four-Way valve is manufactured to our highest standards for use wherseveral two-way valves would otherwise be needed. It is available in a wide
array of flow patterns utilizing an L port, a T port or a double L ball. Four sea
ensure leak tight sealing. The four-way can be produced in a large variety of
body and seat materials from 1/2 - 6 and is available with screwed, socket
weld, butt weld or flanged end connections. Consult factory for specific
application.
Series 51/20 (fabricated from a Series 2000)
The TBV series 51/20 flanged, unibody diverter valve is an integrally flangedesign for use in applications which would normally require two or more
two-way valves. It is available with side or bottom porting in 90 or 180
operation. The 90 operation allows diverting from the bottom or side port to
either of the other two ports with a 90 turn of the handle, but the flow can
never be shut-off. The 180 operation allows diverting with a 180 turn of th
handle and flow can be shut-off at the 90 position. The TBV series 51/20 is
available from 1/2 to 8 with ASME 150 - 300 flanges and in a variety of all
-
5/24/2018 Valvula Esferica Criogenica Tbv
10/20
CT-TBV-022/12-SWP-3MTBV10
VALVES & MEASUREME
TBV VALVES
CRYOGENIC BALL VALVES
Series 2100 (fabricated from a Series 1100)
The unique design of TBVs series 2100 three-piece cryogenic valve incorporates
features that provide long life, safety and low torque. The high strength,
blowout proof stem is used in conjunction with an all welded extended bonnet
and a five chevron V-ring packing to provide leak proof stem seal integrity, as
well as providing live loaded self-adjustment. TBVs specially designed and
formulated Cryofil seats provide low operating torque at cryogenic
temperatures. The TBV series 2100 has a temperature rating down to -452F
and is available up to ASME 1500. It is available in 316L stainless steel, brass
and other commercially available materials with NPT, socket weld, butt weld or
ASME 150 - 1500 flanged end connections, in 1/4 through 8 sizes. For
applications such as vent and bleed lines or intermittent cryogenic service, TBV
offers the non-extended stem. This valve incorporates all of the unique features
of our standard TBV series 2100 cryogenic ball valve.
Series 21/18, 21/20 and 21/28 Flanged Cryogenic Valves
TBV flanged cryogenic valves provide chatter free operation down to -452F
through the use of our exclusively formulated Cryofil seat. The integrity of the
valve is further enhanced by the all welded bonnet design and upstream cavity
relief. The stem is blowout proof and self adjusting to wear and pressure due to
live loading. The standard body materials are 316L stainless steel and are available
with ASME 150-1500 flanges, model dependent, in through 8 sizes.
Series 21/20Series 21/18 Series 21/28
-
5/24/2018 Valvula Esferica Criogenica Tbv
11/20
CT-TBV-022/12-SWP-3M TBV
VALVES & MEASUREME
TBV VALVES
CRYOGENIC BALL VALVES
Series 21/80
The TBV series 21/80 is the large bore (10 - 16), cryogenic valve available
from ASME 150 through 900. This series of valve is full port, trunnion, split
body design. The valve is low temperature tested per Bechtel 3PS-PV00-F000
and Chevron, specification for testing requirements for qualification of valve
low temperature and cryogenic service.
Series 21/51 (fabricated from a Series 1100)
The TBV series 21/51 Cryogenic Diverter incorporates all features found in th
TBV series 2100 and provides diverting capabilities for use where two or mo
two-way valves would normally be necessary, specifically in dual safety relief
The TBV series 21/51 is available in two porting arrangements: 90 operation
and 180 operation. The 90 operation allows flow from a bottom port to b
diverted to either of two outlet ports over a 90 turn of the handle, but can
never shut-off the flow. The 180 operation also diverts a flow from the bot
port to either of two outlet ports, but uses a 180 turn of the handle, allowi
the flow to be shut-off completely at the 90 position.
The TBV series 21/51 is available in full port or standard port from 1/2 thro
8, in 316L stainless or brass, with or without an extended stem. Screw end
socket weld ends, butt weld ends or ASME 150-600 flanged ends are also
available.
Series 21/51A
The TBV series 21/51A high flow cryogenic diverter valve assembly for dual
safety relief systems is designed to meet the high flow requirements of
stationary cryogenic containers. This valve features foolproof 180 operation,
provides positive porting with consistently high Cv during transfer and is suita
for tank pressures to 600 psi. The TBV series 21/51A combines TBVs compac
modular design virtually eliminating the necessity of costly field fabrication.
-
5/24/2018 Valvula Esferica Criogenica Tbv
12/20
CT-TBV-022/12-SWP-3MTBV12
VALVES & MEASUREME
TBV VALVES
SPECIAL SERVICE
Actuation and Gear Operators
TBVs pneumatic and electric actuation packages compliment our complete valve
line. Pneumatic actuation is available with spring return or double acting. Electric
actuation includes all standard voltages. TBV can provide a total control package
including limit switches and positioners to meet customer requirements.
Oxygen Service
TBV valves are commonly applied on oxygen service in either the liquid (cryogeni
or gaseous phase. Because of the danger of oxygen reacting explosively with any
grease, oil or combustible material left in the piping system, TBV valves provided
for oxygen service are:
Inspected for chips, burrs, foreign matter and any other defectsin workmanship
Cleaned and degreased prior to assembly
All tools and handling apparatus degreased as above
Purged and dried with filtered, non-lubricated air
Seats and seals are lubricated with an oxygen compatible lubricant
(Fluorolube) on gaseous O2valves. Cryogenic valves are not lubricated
Black light inspected before assembly
Assembled, tested and air dried in a cleanroom
Capped on each end
Tagged Cleaned for Oxygen Service
Poly bagged and sealed closed
Complies with praxair standard GS-38
Chlorine Service
For the handling of chorine compounds, TBV has developed special designs to
withstand these harsh applications. TBV chlorine valves feature Inconel Belleville
loaded stem seals for automatic compensation of temperature and pressure
fluctuations, an upstream pressure relief hole in the ball or a slotted upstream
end plate to allow expanding chlorine to escape harmlessly upstream, and a wid
variety of available materials to suit each individual application. TBV chlorine
valves are assembled, cleaned and bagged following the recommendations of th
Chlorine Institute Pamphlet 6. The chlorine service option is available for all of
TBVs ball valves and can be tailored to fit any application.
-
5/24/2018 Valvula Esferica Criogenica Tbv
13/20
CT-TBV-022/12-SWP-3M TBV
VALVES & MEASUREME
FE Bonnet for High Performance
For critical applications in which leakage of toxic or volatile organic compoun
cannot be tolerated, TBV provides the fugitive emissions bonnet. The bonne
utilizes a unique design in which the stem packing is live loaded between th
threads on the top of the stem and a shoulder on the stem, rather than a
shoulder in the packing box. Through this floating stem design, TBV has
eliminated the effect of temperature cycles on the packing arrangement. Th
packing consists of a stack of up to ten chevron v-ring sandwiched between
top and bottom adapter rings, or wedge style packing and can be modified
accept a leak off with a lantern ring. This unique design has been proven in
hundreds of installations in services including phosgene and chlorine. Availa
for our entire ball valve line with an optional fire safe version, this fully weld
or integrally cast bonnet can be used with any valve series in any configurati
to prevent the release of dangerous media.
1/4 Turn Bellows Seal
This product line demonstrates the utmost in sealing capabilities (zero leakag
for processes involving volatile organic compounds. Available on most TBV
valves, the ASME 300 is uniquely designed for endurance, and backup
secondary standard sealing as well as all welded integrity. A standard mount
plate allows automation with linear or 90 electrical and pneumatic actuator
Series 7100
The TBV series 7100 swing check valve utilizes our special toggle arm and di
arrangement. This valve is available with integral metal seats. The TBV series
7300 wafer swing check valve can be supplied for use with all ASME flanges
to ASME 600 as standard. Both the TBV series 7100 swing check and the TB
series 7300 wafer swing check valves are available in sizes ranging from 2
through 8.
Series 9100
TBVs series 9100 ball check is available from 1/2 to 2 in a wide variety of
material choices such as stainless, monel, hastelloy and titanium. TBV can
provide the TBV series 9100 with all available end connections including soc
weld, butt weld, screw end or ASME 150 - 900 flanged ends. The TBV series
9100 is controlled by back pressure and can be supplied with a spring set
calibrated from 5-25 psi.
TBV VALVES
SEVERE SERVICE
CHECK VALVES
-
5/24/2018 Valvula Esferica Criogenica Tbv
14/20
VALVES & MEASUREME
CT-TBV-022/12-SWP-3MTBV14
TBV VALVES
INSTRUMENT INSTALLATION DETAILS
TBVs instrument installation details combine optimum measurement technology, proven mounting practices (close couplin
and hardware integration to produce not only the specified 0.075 or 0.05% accuracy and zero stability, but a low installed
cost unequalled in performance and constructability. This system can reduce installation costs by modularizing, pre-
engineering, pre-fabricating, and locking in the optimum transmitter installation in a tamper-proof, foolproof system that
guarantees the rated performance of the transmitter, while lowering the installed cost per instrument loop by 30 to 80%.
INSTRUMENT AND PROCESS VALVES
TBV instrument valves were developed in response
to concerns expressed by plant engineers. Common
problems such as center-to-center spacing in DP
installations, visual position indication, plunging of
impulse lines and tamper proofing have been eliminated
in our instrument valve line. The center-to-center spacing
problem arises in competitive designs since the bonnet
must be removed from the body in order to screw the
valve into the orifice flange next to another valve.
TBV has solved this problem since our instrument valves
can be installed on 2 1/8 centers* by simply removingthe mating valve handle, leaving the valves factory
integrity intact.
Visual position indication is achieved through the use of
an oval safety handle. This handle allows easy position
identification while maintaining safety. These tamper-
proof valves incorporate additional safety through a full
penetration, all welded design which assures that the
body parts can never be separated. Standard valves have
been subjected to bending loads exceeding 27,000 lbs.
without weld failure.
To avoid plunging of impulse lines, all of TBVs Instrument
valves are fully rodable. The bore through the ball and
seats is larger than the body bore. This failure prevents
accidental damage to the ball or seats during the rodding
operation. TBVs ball valves are available in any
commercially produced alloy. In fact, we regularly produce
valves in Alloy 20, Monel, Hastelloy C22, Hastelloy C276,
316L Stainless, Titanium, Zirconium and more. TBV can
also accommodate the entire spectrum of end
connections on our instrument product line. All are
available with threaded, socket weld, butt weld or flanged
end connections and all can be ordered as fire safe.
* With exception of the TBV series 6800 + 6900.
Flow Applications Pressure Applications Level Applications
-
5/24/2018 Valvula Esferica Criogenica Tbv
15/20
CT-TBV-022/12-SWP-3M TBV
VALVES & MEASUREME
TBV VALVES
SEAT RATING CHART
psig (BAR)
4000 (276)
3500 (241)
3300 (207)
2500 (172)
2000 (138)
1500 (103)
1000 (69)
500 (34)
0 (0)
F 0 100 200 300 400 500 600 700 800 900 1000 1
C (-18) (38) (93) (149) (204) (260) (316) (371) (427) (482) (538) (5
TEMPERATURE F (C)
PRESSUREpsig
(BAR)
Extended pressures and temperatures may be achieved by altering design for specific applications.
Consult factory with service conditions.
Seat Material Identification Code
T-Virgin PTFE White
G-Reinforced PTFE White (Red speckles)
U-Ultrafil Black
C-Cryofil* White (Identifying groove)
F-Thermafil (PEEK) Light Brown
P-U.H.M.W.P. Translucent White
D-Delrin Dark Brown
K-CTFE Translucent
M-Metal Silver
H-Graphite Black
Graphite and metal seats are available for services up to 1000F, at varying pressures, dependant on media and service
conditions. Consult factory for specific rating.
* Registered trademark of TBV.
Extended pressures and temperatures may be achieved by altering designs for specific applications. Consult factory w
service conditions.
Metal
Thermafil
Delrin AFKel-F
UHMWPolyethelyne
Glass FilledPTFE
VirginPTFE
Ultrafil
-
5/24/2018 Valvula Esferica Criogenica Tbv
16/20
VALVES & MEASUREME
CT-TBV-022/12-SWP-3MTBV16
TBV VALVES
HOW TO ORDER
* For valves with different end connections indicate upstream (first), downstream (second).** Special O.D. Wall Thickness and Length.
01 = 1/802 = 1/403 = 3/805 = 1/207 = 3/410 = 112 = 1 1/415 = 1 1/217 = 1 x 3/420 = 221 = 2 x 123 = 1/4 x 3/825 = 2 1/2
30 = 332 = 3/8 x 1/435 = 3 1/240 = 451 = 1/2 x 152 = 1/2 x 1/457 = 1/2 x 3/460 = 671 = 3/4 x 175 = 3/4 x 1/280 = 8X0 = 10X2 = 12X4 = 14X6 = 161A = 1 x 1/22A = 1/4 x 1/2
S = Standard PortF = Full Port
11 = 1100-3 Piece16 = 1600-Tank Bottom18 = 1800-2 Piece
ASME Flange20 = 2000-Unibody
Flange21 = 2100-Cryogenic2B = 21/20-Cryogenic
Unibody Flanged2C = 21/31 Cryogenic
Wafer2D = 21/51 Cryogenic
Diverter
2F = 21/51/20Cryogenic UnibodyFlanged Diverter
2G = 21/18-Cryogenic2-piece ASMEFlanged
2H = 21/61 Series Cryo2K = 21/65 Series Cryo2L = 21/64 Series Cryo2P = 21/51/18 Split
body FlangedCryogenic Diverter
2R = Switching DiverterNon-ExtendedStem - Bottom Port
2S = Switching DiverterExtended Stem- Side Port
2T = Switching DiverterNon-ExtendedStem - Side Port
2V = Cryogenic 28002W = Cryogenic Large
Bore, Split Body28 = 2800-Cast Full Port31 = 3100-Wafer32 = 3200-Steam Let
Down33 = Severe Service
Valve3L = 3100L-Lugged
Wafer41 = 4100-Welded43 = 4300-Welded w /
ds Relief on Ball46 = 41/61-Male End
4100 Unibody50 = 51/20-DiverterUnibody Flanged
51 = 5100-Diverter53 = 51/18 Diverter61 = 6100-Orifice Tap
Gauge66 = 61/41/61-Double
Male End AllWelded
71 = 7100-Swing Check73 = 71/31-Wafer
Swing Check91 = 9100-Ball Check
BWT = Buttweld Ext. &Tube Ends**
B_ = Buttweld +Schedule
(B40 = Schedule 40)CPE = CPI EndsFSE = NPT Female ThreadFSW = Female Socket
WeldGRE = Graylok EndsMFD = Manifold
ConnectionMLS = Metal Seal
MSE = NPT Male ThreadMST = Straight Thread
with O-RingMSW= Male Socket WeldMWE = Male Weld EndSOE = O.D. Tube End
Socket WeldSPL = SpecialTCE = Ladish EndTE_ = Tube End (K,L,M) Socket WeldUNE = Union End150 = ASME 150 Flng RF15L = ASME150 Lap Joint
Flanged15R = ASME 150 RTJ300 = ASME 300 Flng RF30L = ASME 300 Lap
Joint Flanged30R = ASME 300 RTJ600 = ASME 600 Flng RF60R = ASME 600 RTJ900 = ASME 900 Flng RF005 = ASME 1500 Flng
RF05R = ASME 1500 RTJ
0 = IREB1 = MSE2 = MSW3 = FSE4 = FSW5 = I-Flange6 = BW807 = BW408 = BW160
9 = I-Flange NeutralEXAMPLE: 1 x 3 = MSE X FSE
A2 = Alloy 20AL = AluminumBR = BrassCS = Carbon SteelD2 = Super Duplex
StainlessUNS-32750
D3 = DuplexStainlessUNS-S31803
HB = Hastelloy BHC = Hastelloy CH3 = Hastelloy B-3
H2 = HastelloyC-22
IN = InconelIY = IncoloyLC = LCB Carbon
SteelM4 = Monel 400M5 = Monel K500N2 = Nickel 200T2 = Titanium
Gr 2T5 = Titanium
Gr 5T7 = Titanium
Gr 7T12 = Titanium
Gr 12TN = Tantalum
ZR = Zirconium34 = 304 SS36 = 316 SS37 = 317 SS4L = 304L SS6L = 316L SS
B = ASTM A193B7M x A194 7M
C = ASTM A193 B8CL2 x A194 Gr 8
D = Alloy 20E = ASTM A193B8
CL1 x A194 Gr 8FF = ASTM A540 B21 x
A194 Gr 2HG = ASTM A320 L7 x
A194 Gr 4H = Inconel 718J = 410SS A193 Gr
B6K = 304L SSL = Hastelloy B2M = Monel 400N = ASTM A320 Gr
B8PQ = A193 Gr B8 x
ASTM A194 Gr 8W = All Welded0 = None1 = Carbon Steel2 = 300 SS3 = ASTM A193 B7 x
A194 2H4 = ASTM A193 B8M
x A194 8M5 = Monel K-5006 = Hastelloy C
7 = 316 SS8 = Gr 5 Titanium9 = HAST C-276
01 = 90 Operation(Diverter Valve)
02 = 180 Operation(Diverter Valve)
04 = 4 SeatedAH = Act. Prep w/std
HandleAI = Act. InstalledAP = Prepared for
ActuationBS = Bellows SealCA = Cutaway SampleCB = Enclosed Bolting
CD = Cleaned andDegreased
CS = Crusher SeatsCF = Cavity FillerCL = Chlorine CleaninEB = Extended BonneEE = Extended EndsEP = Electro PolishES = Extended StemFE = Fugitive Emission
BonnetFG = Forged MaterialFL = Fire LipFS = Fire SafeGO = Gear OperatorGS = Grounding SprinHF = Hydro-Fluoric SeHP = High Pressure
LG = Locking GearOperator
LH = Locking HandleLO = Locking Oval HaLR = Lantern RingLS = locking SS Oval
HandleLV = Lever HandleM1 = 15 Control SeatM3 = 30 Control SeatM6 = 60 Control SeatM9 = 90 Control SeatNE = Non-ExtentedOH = Oval HandleOS = Stainless Steel O
HandleOX = Oxygen CleanedPC = Phosgene Clean
PM = Panel MountedRS = Self Relieving SeSJ = Steam JacketSL = Spring Loaded/9SP = Side Port/5100SR = Spring Return HaTR = TrunnionVB = Vented BallVS = Vacuum ServiceW1 = Spiral Wound Bo
SealW2 = Spiral Wound Bo
Seal 316S GrafoW3 = Spiral Wound Bo
Seal Ti Gr 2 TFEW4 = Spiral Wound Bo
Ti Gr 2 GrafoilW5 = Spiral Wound Bo
Gasket Hast CGrafoil
A = Arlon 1555PEEK
B = BunaC = CryofilD = Delrin AFE = E.P.R.F = ThermafilG = 15% GF TFEH = Grafoil/GraphiteK = CTFEL = VespelM = MetalN = Nylon
P = UHMWPQ = E.P.D.M.S = StelliteT = Virgin TFEU = Ultrafil 25V = Viton1 = Tefzel2 = Kalrex3 = PFA4 = FEP5 = Ertelyte
(CERTAIN COMBINATIONSNOT AVAILABLE)
VALVE SPECIFICATION CHART
Size Porting SeriesEnd
ConnectionsBody / EndMaterial*
Ball / StemMaterial
Seat / SealMaterial
Bolting Modifie
for mixed
combination
of end
plates
-
5/24/2018 Valvula Esferica Criogenica Tbv
17/20
VALVES & MEASUREME
CT-TBV-022/12-SWP-3M TBV
CERTIFICATIONS
AFTERMARKET SERVICES
Aftermarket Services
Supplies replacement valves and parts:
Maintains a full inventory of new and
reconditioned valves for immediate delivery
Provides factory warranty support for all
Cameron OEM brands as well as service for mostother valves
Field Service and Technical Support
Field service technicians on call 24 hours a day
7 days a week to handle service issues wherever
they arise
Provides equipment installation, field repairs,
as well as track and perform scheduled
maintenance
Customer Property Repair
The Customer Property Repair program allows
Cameron valve customers to store assets at ou
service centers throughout the world
Valves tracked in electronic database accessibthrough the Internet
Remanufactured Products
Offers a broad range of API-compliant
reconditioned equipment with fast delivery
Total Valve Management
Supply and service automation and control
packages
Assist with valve installation, commissioning a
start-up
Camerons Aftermarket Services goal is to help
customers lower the total cost of valve ownership. To t
end we offer a full range of services from over twenty-
Service Centers worldwide and can provide experien
personnel trained to meet the specific service requirem
of each valve type.
-
5/24/2018 Valvula Esferica Criogenica Tbv
18/20
VALVES & MEASUREME
CT-TBV-022/12-SWP-3MTBV18
TRADEMARK INFORMATION
TBV is a registered trademark which is owned by Cameron.
This document contains references to registered trademarks or product designations,
which are not owned by Cameron.
Trademark Owner
DELRIN E.I. DuPont De Nemours & Company
HASTELLOY Haynes International, Inc.
INCONEL INCO Nickel sales, Inc.
MONEL INCO Alloys International, Inc.
PEEK Vitrex PLC Corp United Kingdom
TEFLON E.I. DuPont De Nemours & Company
VITON E.I. DuPont De Nemours & Company
-
5/24/2018 Valvula Esferica Criogenica Tbv
19/20
VALVES & MEASUREME
CT-TBV-022/12-SWP-3M TBV
-
5/24/2018 Valvula Esferica Criogenica Tbv
20/20
Cameron Printed in USA 2/12-SWP-3M CT-TBV-02
VALVES & MEASUREME
Valves & Measurement
3250 Briarpark Drive, Suite 300Houston, TX 77042USA Toll 800 323 9160
For the most current contact and location information go to: www.c-a-m.com
Cameron strives for continuous improvement in all aspects of our business. Cameronreserves the right to modify designs and specifications without notice or obligation. Nothingcontained in this brochure is intended to extend any type of warranty, expressed or implied.