u.s. patent numbers 5,069,042 5,522,229 mini waterless in ...the ez-trap condensate trap or overflow...

2
U.S. Patent Numbers 5,069,042 5,522,229 Mini Waterless In-Line Condensate Trap Scan for more info RectorSeal® 2601 Spenwick Drive - Houston, TX 77055 ph: 713.263.8001 - 800.231.3345 fax: 713.263.7577 - 800.441.0051 www.rectorseal.com - Like Us on Facebook 961735 ® Model No. 83180 (EZT180) Kit Contents Mini Trap (1) Rubber Adaptor (1) Cleaning Label (1) 0 21449 83180 2 LIMITED WARRANTY. RectorSeal ® warrants to the original consumer purchaser (“Purchaser”) of its product, EZ Trap ® , that it is free from defects in material or workmanship. If within two years (24 months) from the date of the original consumer purchase this product shall prove to be defective, it shall be repaired or replaced at RectorSeal’s option. Your original receipt of purchase is required to determine warranty eligibility. 2 Year

Upload: others

Post on 22-Jan-2020

7 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: U.S. Patent Numbers 5,069,042 5,522,229 Mini Waterless In ...The EZ-Trap condensate trap or overflow switch purchased by you is unconditionally warrantied to be free from defects in

(EZT113)

U.S. Patent Numbers 5,069,042 5,522,229

Mini WaterlessIn-LineCondensate Trap

Scan for more info

RectorSeal® 2601 Spenwick Drive - Houston, TX 77055ph: 713.263.8001 - 800.231.3345 fax: 713.263.7577 - 800.441.0051www.rectorseal.com - Like Us on Facebook

961735

® Model No.

83180 (EZT180)

Kit ContentsMini Trap (1)

Rubber Adaptor (1)Cleaning Label (1)

0 2 1 4 4 9 8 3 1 8 0 2

LIMITED WARRANTY. RectorSeal® warrants to the original consumer purchaser (“Purchaser”) of its product, EZ Trap®, that it is free from defects in material or workmanship. If within two years (24 months) from the date of the original consumer purchase this product shall prove to be defective, it shall be repaired or replaced at RectorSeal’s option. Your original receipt of purchase is required to determine warranty eligibility.

2 Year

Page 2: U.S. Patent Numbers 5,069,042 5,522,229 Mini Waterless In ...The EZ-Trap condensate trap or overflow switch purchased by you is unconditionally warrantied to be free from defects in

INSTALLATION INSTRUCTIONS

Model EZT-1801. Trap must be fitted at least 12” below indoor unit

(Figure 1).2. Ensure that Black Valve Assembly is perpendicular to

or facing away from wall to facilitate cleaning.3. For 5/8” (16mm) drain hose, insert end of upper drain hose

into top of Trap (Wide End) and seat firmly (Figure 2).4. For 9/16” (14mm) drain hose, insert Rubber Adaptor into

top of Trap and insert hose into Adaptor and seat firmly(Figure 3).

CAUTION: TRAP MUST BE INSTALLED VERTICALLY–WIDE END UP AND NARROW END DOWN – FORCONDENSATE TO FLOW. INCORRECT INSTALLATION WILL CAUSE BACK-UP OF CONDENSATE.5. Insert bottom end of Trap (Narrow End) into top of lower

drain hose (Figures 4 & 5).6. Wrap inlet and outlet connection with PVC Tape

(Figure 6).7. Fit Hose/Trap assembly to wall with 2 pipe brackets

3” from Trap (Figure 5).

IMPORTANT NOTES1. FOR USE WITH MINISPLIT AIR CONDITIONERS ONLY.2. REMOVE TRAP BEFORE CLEANING COOLING COIL WITH

CHEMICAL CLEANER.3. DO NOT GLUE THIS TRAP.4. WHERE POSSIBLE, INSTALL WITHIN 6’ OF GROUND TO

FACILITATE INSPECTION AND CLEANING.5. TRAP IS NOT REQUIRED IF CONDENSATE PUMP IS FITTED.6. CLEAN AT LEAST ONCE ANNUALLY OR MORE OFTEN IF

REQUIRED.7. ENSURE THAT BLEED HOLES ARE NOT BLOCKED.8. THIS DEVICE MUST BE INSTALLED STRICTLY IN ACCORDANCE

WITH MANUFACTURER’S INSTRUCTIONS TO ENSURE PROPEROPERATION AND IN ACCORDANCE WITH ALL APPLICABLELOCAL PLUMBING, DRAINAGE AND/OR MECHANICAL CODES.

Figure 2 Figure 3

Figure 4

Figure 6Figure 5

16mm DRAINHOSE

WATERFLOW

14mm DRAINHOSE

16mm DRAINHOSE

14mm DRAINHOSE

PVC TAPE

PVC TAPE

EZ-TRAP WARRANTY

The manufacturer disclaims all implied and express warranties, including the impliedwarranty of merchantability and the implied warranty of fitness for a particularpurpose, except as follows:

The EZ-Trap condensate trap or overflow switch purchased by you is unconditionallywarrantied to be free from defects in material and workmanship under normal use fora period of three (3) years from date of purchase, providing it is installed and operatedstrictly in accordance with manufacturer’s installation instructions.

If the product is found to be defective or otherwise fails in normal use, you may returnit for replacement. All freight charges for the return of the product shall be borne byyou. The manufacturer will pay outgoing freight charges for the replacement product.

Defective products returned to EZ-Trap prepaid will be repaired or replaced free ofcharge. Replacement product will, to the extent such product is then available inmanufacturer’s inventory, be of similar type, color and kind. Manufacturer retains theright to substitute product if replacement product does not conform in terms of color,type and specifications to the original product, if no longer available.

This warranty does not cover replacement labor or any cost, claim or incident to anydefect nor does it cover any consequential damages. The sole liability of themanufacturer under this warranty is limited to the replacement of defective product.Product damaged by improper use, accident, neglect, alteration, abuse or improperinstallation is excluded from this warranty.

180 INSTALL 6/07

CONTENTS1 - EZT-180 MiniTrap1 - Rubber Adaptor for 9/16” (14mm) Drain Hose 1 - Cleaning Label

MINI TRAP FOR MINISPLIT AIR CONDITIONERS

Model EZT-180

EZ-TRAP INC.3 Kellogg Court, Unit 10 Edison, NJ 08817phone: 732-248-8066 fax: 732-248-8068e-mail: [email protected] web: www.eztrap.com

THE TRAPEXPERTS

EZT-180

©2007

EZT-180EZT-180

WARNINGS1. THIS TRAP IS DESIGNED

FOR USE WITH NO-KINKCORRUGATED PE DRAIN HOSE (DH-16). THIN WALL VINYL HOSE KINKS VERY EASILY AND SHOULD NOT BE USED FOR THISAPPLICATION.

2. DO NOT INSTALL TRAPHORIZONTALLY

3. DRAIN HOSE EXITING UNITMUST HAVE SLOPE TOFACILITATE CONDENSATEFLOW

Figure 1

WATERFLOW

WATERFLOW

3”

3”

12” MINIMUM

SLOPE

WATERFLOW

WATERFLOW

INSTALLATION INSTRUCTIONS

Model EZT-1801. Trap must be fitted at least 12” below indoor unit

(Figure 1).2. Ensure that Black Valve Assembly is perpendicular to

or facing away from wall to facilitate cleaning.3. For 5/8” (16mm) drain hose, insert end of upper drain hose

into top of Trap (Wide End) and seat firmly (Figure 2).4. For 9/16” (14mm) drain hose, insert Rubber Adaptor into

top of Trap and insert hose into Adaptor and seat firmly(Figure 3).

CAUTION: TRAP MUST BE INSTALLED VERTICALLY–WIDE END UP AND NARROW END DOWN – FORCONDENSATE TO FLOW. INCORRECT INSTALLATION WILL CAUSE BACK-UP OF CONDENSATE.5. Insert bottom end of Trap (Narrow End) into top of lower

drain hose (Figures 4 & 5).6. Wrap inlet and outlet connection with PVC Tape

(Figure 6).7. Fit Hose/Trap assembly to wall with 2 pipe brackets

3” from Trap (Figure 5).

IMPORTANT NOTES1. FOR USE WITH MINISPLIT AIR CONDITIONERS ONLY.2. REMOVE TRAP BEFORE CLEANING COOLING COIL WITH

CHEMICAL CLEANER.3. DO NOT GLUE THIS TRAP.4. WHERE POSSIBLE, INSTALL WITHIN 6’ OF GROUND TO

FACILITATE INSPECTION AND CLEANING.5. TRAP IS NOT REQUIRED IF CONDENSATE PUMP IS FITTED.6. CLEAN AT LEAST ONCE ANNUALLY OR MORE OFTEN IF

REQUIRED.7. ENSURE THAT BLEED HOLES ARE NOT BLOCKED.8. THIS DEVICE MUST BE INSTALLED STRICTLY IN ACCORDANCE

WITH MANUFACTURER’S INSTRUCTIONS TO ENSURE PROPEROPERATION AND IN ACCORDANCE WITH ALL APPLICABLELOCAL PLUMBING, DRAINAGE AND/OR MECHANICAL CODES.

Figure 2 Figure 3

Figure 4

Figure 6Figure 5

16mm DRAINHOSE

WATERFLOW

14mm DRAINHOSE

16mm DRAINHOSE

14mm DRAINHOSE

PVC TAPE

PVC TAPE

EZ-TRAP WARRANTY

The manufacturer disclaims all implied and express warranties, including the impliedwarranty of merchantability and the implied warranty of fitness for a particularpurpose, except as follows:

The EZ-Trap condensate trap or overflow switch purchased by you is unconditionallywarrantied to be free from defects in material and workmanship under normal use fora period of three (3) years from date of purchase, providing it is installed and operatedstrictly in accordance with manufacturer’s installation instructions.

If the product is found to be defective or otherwise fails in normal use, you may returnit for replacement. All freight charges for the return of the product shall be borne byyou. The manufacturer will pay outgoing freight charges for the replacement product.

Defective products returned to EZ-Trap prepaid will be repaired or replaced free ofcharge. Replacement product will, to the extent such product is then available inmanufacturer’s inventory, be of similar type, color and kind. Manufacturer retains theright to substitute product if replacement product does not conform in terms of color,type and specifications to the original product, if no longer available.

This warranty does not cover replacement labor or any cost, claim or incident to anydefect nor does it cover any consequential damages. The sole liability of themanufacturer under this warranty is limited to the replacement of defective product.Product damaged by improper use, accident, neglect, alteration, abuse or improperinstallation is excluded from this warranty.

180 INSTALL 6/07

CONTENTS1 - EZT-180 MiniTrap1 - Rubber Adaptor for 9/16” (14mm) Drain Hose 1 - Cleaning Label

MINI TRAP FOR MINISPLIT AIR CONDITIONERS

Model EZT-180

EZ-TRAP INC.3 Kellogg Court, Unit 10 Edison, NJ 08817phone: 732-248-8066 fax: 732-248-8068e-mail: [email protected] web: www.eztrap.com

THE TRAPEXPERTS

EZT-180

©2007

EZT-180EZT-180

WARNINGS1. THIS TRAP IS DESIGNED

FOR USE WITH NO-KINKCORRUGATED PE DRAIN HOSE (DH-16). THIN WALL VINYL HOSE KINKS VERY EASILY AND SHOULD NOT BE USED FOR THISAPPLICATION.

2. DO NOT INSTALL TRAPHORIZONTALLY

3. DRAIN HOSE EXITING UNITMUST HAVE SLOPE TOFACILITATE CONDENSATEFLOW

Figure 1

WATERFLOW

WATERFLOW

3”

3”

12” MINIMUM

SLOPE

WATERFLOW

WATERFLOW

INSTALLATION INSTRUCTIONS

Model EZT-1801. Trap must be fitted at least 12” below indoor unit

(Figure 1).2. Ensure that Black Valve Assembly is perpendicular to

or facing away from wall to facilitate cleaning.3. For 5/8” (16mm) drain hose, insert end of upper drain hose

into top of Trap (Wide End) and seat firmly (Figure 2).4. For 9/16” (14mm) drain hose, insert Rubber Adaptor into

top of Trap and insert hose into Adaptor and seat firmly(Figure 3).

CAUTION: TRAP MUST BE INSTALLED VERTICALLY–WIDE END UP AND NARROW END DOWN – FORCONDENSATE TO FLOW. INCORRECT INSTALLATION WILL CAUSE BACK-UP OF CONDENSATE.5. Insert bottom end of Trap (Narrow End) into top of lower

drain hose (Figures 4 & 5).6. Wrap inlet and outlet connection with PVC Tape

(Figure 6).7. Fit Hose/Trap assembly to wall with 2 pipe brackets

3” from Trap (Figure 5).

IMPORTANT NOTES1. FOR USE WITH MINISPLIT AIR CONDITIONERS ONLY.2. REMOVE TRAP BEFORE CLEANING COOLING COIL WITH

CHEMICAL CLEANER.3. DO NOT GLUE THIS TRAP.4. WHERE POSSIBLE, INSTALL WITHIN 6’ OF GROUND TO

FACILITATE INSPECTION AND CLEANING.5. TRAP IS NOT REQUIRED IF CONDENSATE PUMP IS FITTED.6. CLEAN AT LEAST ONCE ANNUALLY OR MORE OFTEN IF

REQUIRED.7. ENSURE THAT BLEED HOLES ARE NOT BLOCKED.8. THIS DEVICE MUST BE INSTALLED STRICTLY IN ACCORDANCE

WITH MANUFACTURER’S INSTRUCTIONS TO ENSURE PROPEROPERATION AND IN ACCORDANCE WITH ALL APPLICABLELOCAL PLUMBING, DRAINAGE AND/OR MECHANICAL CODES.

Figure 2 Figure 3

Figure 4

Figure 6Figure 5

16mm DRAINHOSE

WATERFLOW

14mm DRAINHOSE

16mm DRAINHOSE

14mm DRAINHOSE

PVC TAPE

PVC TAPE

EZ-TRAP WARRANTY

The manufacturer disclaims all implied and express warranties, including the impliedwarranty of merchantability and the implied warranty of fitness for a particularpurpose, except as follows:

The EZ-Trap condensate trap or overflow switch purchased by you is unconditionallywarrantied to be free from defects in material and workmanship under normal use fora period of three (3) years from date of purchase, providing it is installed and operatedstrictly in accordance with manufacturer’s installation instructions.

If the product is found to be defective or otherwise fails in normal use, you may returnit for replacement. All freight charges for the return of the product shall be borne byyou. The manufacturer will pay outgoing freight charges for the replacement product.

Defective products returned to EZ-Trap prepaid will be repaired or replaced free ofcharge. Replacement product will, to the extent such product is then available inmanufacturer’s inventory, be of similar type, color and kind. Manufacturer retains theright to substitute product if replacement product does not conform in terms of color,type and specifications to the original product, if no longer available.

This warranty does not cover replacement labor or any cost, claim or incident to anydefect nor does it cover any consequential damages. The sole liability of themanufacturer under this warranty is limited to the replacement of defective product.Product damaged by improper use, accident, neglect, alteration, abuse or improperinstallation is excluded from this warranty.

180 INSTALL 6/07

CONTENTS1 - EZT-180 MiniTrap1 - Rubber Adaptor for 9/16” (14mm) Drain Hose 1 - Cleaning Label

MINI TRAP FOR MINISPLIT AIR CONDITIONERS

Model EZT-180

EZ-TRAP INC.3 Kellogg Court, Unit 10 Edison, NJ 08817phone: 732-248-8066 fax: 732-248-8068e-mail: [email protected] web: www.eztrap.com

THE TRAPEXPERTS

EZT-180

©2007

EZT-180EZT-180

WARNINGS1. THIS TRAP IS DESIGNED

FOR USE WITH NO-KINKCORRUGATED PE DRAIN HOSE (DH-16). THIN WALL VINYL HOSE KINKS VERY EASILY AND SHOULD NOT BE USED FOR THISAPPLICATION.

2. DO NOT INSTALL TRAPHORIZONTALLY

3. DRAIN HOSE EXITING UNITMUST HAVE SLOPE TOFACILITATE CONDENSATEFLOW

Figure 1

WATERFLOW

WATERFLOW

3”

3”

12” MINIMUM

SLOPE

WATERFLOW

WATERFLOW

83180 Installation instructions (EZT180)