LEG CLIP

LEG CLIP ASSEMBLY

ROUND HEADSCREW

SQUARE TRAYS - (CORNER FIT)

D-SHAPED TRAY

PENTAGON TRAYSRECTANGULAR TRAYS

(CORNER FIT)

OFFSET QUADRANT TRAYS

RECTANGULAR TRAYS(ALCOVE FIT)

SQUARE TRAYS(ALCOVE FIT)

RECTANGULAR TRAYS(CORNER FIT)

RECTANGULAR TRAYS(ALCOVE FIT)

WALK IN TRAYS

PLIN

TH+

2mm

GAP

SHOWER TRAY

BASE BOARD

BATT

EN SAND & CEMENT

PLINTH

SHOWER PLINTH CLIP

FITTING DIAGRAM (When using baseboard)

FLOOR COVERING/TILES

WOODEN BLOCK

G

H

60

60

200 MIN

200

M

IN

TWO PACKS OF 6FIG 3

60

60

200

M

IN

200 MIN

PACK OF 8FIG 2

SIDE PANEL FIT.

K

60

60

200

MIN

200 MIN

PACK OF 6

EDGE OF TRAY TO PLYWOOD BASE.

FIG 1

111

86

WAL

L

SHOWER TRAY

BASE BOARD

FLOOR

BATT

EN SAND & CEMENT

WAL

L

SHOWER TRAY

BASE BOARD

FLOOR

BATT

EN SAND & CEMENT

U 6

0

200

M

IN

200 MIN

60

SQUARE TRAYS

200

MIN

60

60

QUADRANT TRAYS

60

200 MIN

200

M

IN

60

OFFSET QUADRANT TRAYS

EDGE OF TRAY TO PLYWOOD BASE.

200

M

IN

200 MIN

60

60

RECTANGULAR TRAYS - 1000, 1100 & 1200mm

200 MIN

60

200

M

IN

60

RECTANGULAR TRAYS - 1300, 1400, 1500, 1600, 1700 & 1800mm

UNIVERSAL LEG SET & PLINTH KIT INSTRUCTIONPLEASE READ THESE INSTRUCTIONS FULLY AND FAMILIARISE YOURSELF WITH THE COMPONENTS BEFORE PROCEEDING.•

FULLY INSPECT THE TRAY, PAYING ATTENTION TO THE RED LABEL INSTRUCTION. YOUR TRAY COMES WITH A PROTECTIVE FILM. PEEL BACK TO INSPECT THEN REPLACE. FITTING OF THIS TRAY OR LEG KIT WILL BE TAKEN AS ACCEPTANCE OF QUALITY.

IF YOU DON'T FIT THIS TRAY AS PER THE INSTRUCTIONS GIVEN, YOUR WARRENTLY WILL BE NULL AND VOID. •

IMPORTANTYOU MUST FIT A BASEBOARD AND BATTENS WHEN USING A•

LEG KIT WITH A TRAY 1200mm AND ABOVE.BASEBOARD AND BATTENS ARE NOT SUPPLIED WITH THIS KIT.•TRAYS BELOW 1200mm. IT IS STILL HIGHLY RECOMMENDED YOU •

FIT USING A BASEBOARD AND BATTENS. (IF NOT USING SEE FIG 1)

LEG FITTING1000/1100/1200/1300/1400/1600/1700

*SPACE THE LEGS OUT AS EVENLY AS POSSIBLE TO HELP SPREAD FORCES EQUALLY***THIS IS A GUIDE ONLY**

SINGLE ENTRY TRAY

EQUAL QUADRANT TRAYS

LEG FITTING700/760/800/900/1000

*SPACE THE LEGS OUT AS EVENLY AS POSSIBLE TO HELP SPREAD FORCES EQUALLY***THIS IS A GUIDE ONLY**

MOVE THE TRAY INTO THE DESIRED POSITION AND SCRIBE A LINE ON THE FLOOR WHERE THE TRAY WILL SIT INCLUDING THE WASTE.

CUT PLYWOOD BASEBOARD (18mm MINIMUM) SO IT SITS 60mm BACK FROM THE FRONT EDGE OF THE TRAY(SEE DIAGRAMS ACROSS).

DRY FIT THE SHOWER TRAY WASTE AND PIPE TO ENSURE IT DOESN'T FOUL ON PLYWOOD BASE.

FIT LEGS TO PLYWOOD BASEBOARD USING COUNTER SUNK SCREWS SUPPLIED. RECOMMENDED LEG POSITIONING ACROSS.

THE OVERALL HEIGHT FROM THE FLOOR TILE TO THE UNDERSIDE OF THE TRAY SHOULD BE 'PLINTH HEIGHT + 2mm' SEE DIAGRAM ABOVE.YOU MAY NEED TO REMOVE THE LEG'S LOCKING NUT IF FITTING ON THE LEAST EXTENSION.

ANY TRAY 1300mm AND ABOVE WILL REQUIRE •x2 PACKS OF 6 LEGS.

FIG 1

THE SHOWER TRAY PLINTH MAYBE SUPPLIED OVER LENGTH. PLACE ONTO THE TRAY FOLLOWING THE CONTOUR OF THE TRAY. MARK AND CUT SHOWER PLINTH.

1.

MAKE ALL WASTE CONNECTIONS AND CHECK FOR LEAKS.

FIT SHOWER PLINTH WHEN ALL WORKS ARE FINISHED.

4.

TRAY REMOVED FOR CLARITY

SCRIBE A LINE ON THE FLOOR WHERE THE PANEL WILL SIT. PLACE THE PANEL ON THE FLOOR BEHIND THE SCRIBED LINE TAKING THE PANEL'S RETURN LIP INTO

ACCOUNT. USE SEVERAL SMALL WOODEN BLOCKS TO ENSURE THE PANEL REMAINS STABLE. ALSO ENSURE LEVEL WITH A SPIRIT LEVEL.

2.

A

C

2mm

BACK

DO NOT FIT USING AN IMPACT DRIVER.

O

WAL

L

BASE BOARD

FLOOR

BATT

EN SAND & CEMENT

INLINE

PLINTH

SHOWER PLINTH CLIP

FLOOR COVERING/TILES

WOODEN BLOCK

SHOWER TRAY

FIT PLINTH CLIPS TO THE UNDERSIDE OF THE TRAY USING DIAGRAMS OVERLEAF AS A GUIDE. SET THE CLIP 2mm BACK FROM THE FRONT EDGE OF THE TRAY. FIT USING 3.5 x 16mm ROUND HEAD SCREWS SUPPLIED.

NOTCHED WOODEN BLOCKS CAN BE USED BEHIND THE PLINTH TO HELP KEEP THE PLINTH STABLE, (NOT SUPPLIED).

2.

V

FIT BATTENS TO THE WALL USING SUITABLE FIXINGS. BATTENS SHOULD BE FROM THE FLOOR TO THE UNDERSIDE OF THE BASEBOARD.

PLACE THE BASEBOARD ONTO BATTENS AND PIN IN PLACE. ENSURE BASEBOARD IS LEVEL WITH A SPIRIT LEVEL.

APPLY A SUFFICIENT SAND & CEMENT BED (OR FLEXIBLE FLOOR TILE ADHESIVE) TO THE BASEBOARD TO FORM A LEVEL BED. PLACE THE TRAY ON THE BED AND TAMPER ENSURING A GAP 'PLINTH HEIGHT + 2mm' FROM FLOOR TILE TO UNDERSIDE OF TRAY. TRAY MUST BE LEVEL IN ALL PLANES.

3.

PLINTH KIT FITTING

1.DEPENDING ON WHICH LEG CLIP HAS BEEN SUPPLIED, FIT THE PANEL CLIPS TO THE UNDERSIDE OF THE TRAY AS ILLUSTRATED IN THE BEST FIT DIAGRAMS OVERLEAF.

WE RECOMMEND THAT THE METAL CLIP IS FITTED SO THAT IT OVERHANGS THE TRAY 4mm.

THE PLASTIC CLIP SHOULD BE FITTED TO SUIT THE PANEL RETURN DEPTH; AS THIS MAY VARY.

DO NOT SLIDE THE TRAY WHEN MOVING INTO POSITION AS THIS CAN LOOSEN THE LEG FIXINGS.