ujjbq for pmi (positive material identification) - grimas pmi (positive material identification) ......
TRANSCRIPT
uJjbq∆ for PMI (Positive Material Identification)Fast QC!
PMI • QC / QA • FAC • Automotive •Aerospace • …
X-MET5000 & X-MET5100 - Choice of two robust highly productive XRF analyzers, one with revolutionary Light Element capability for fast QC and materials verification in just one second!
• This cutting edge technology delivers a five times faster measurement speed, much better detection limits and significant accuracy improvement over conventional systems.
• 6061 / 6063 ID in seconds!
X-MET5100 combines Oxford Instruments’ ground-breaking • Silicon Drift Detector (SDD) with• a powerful 45kV X-ray tube
X-MET5100 – On top of the range
• Unparalleled speed: complete alloy analysis and grade ID in seconds
• Revolutionary Light Element analysis (Mg, Al, Si, P, S) without awkward vacuum pumps or helium bottles
• Invaluable tool for aluminium measurement and analysis of alloys which may contain large amounts of light elements (Mg, Al, Si, P, S).
uJjbq5000 –Reliable material verification
What’s more,uJjbq5100 provides:
• Reliable identification of a wide range of alloy grades
• Identification of close grades such as 304/321 or Grade CPTi/Ti-7 in less than 5 seconds
• Traceable Empirical Calibration to certified reference materials
• Withstands test piece surface temperatures up to 400ºC
• Totally non-destructive testing
High speed PMI and Quality Control/Assurance with the X-MET series
• Analyze known and unknown samples – with ease - Just point, shoot and read the result
• Grade Identification in 2-5 seconds measuring time X-MET5000in 1 second X-MET5100
• Trace elements (<0.2%) in 5-10 seconds X-MET5000in 2 seconds X-MET5100
• Close separations e.g. 304/321 separation or Grade 7/CPTi in 5 seconds X-MET5000in 1 second X-MET5100
Grade Identification and highly accuratealloy analysis in seconds
X-MET5000 vs. X-MET5100Key Performance Characteristics
0,006%0,012%Nb in steel (5 s meas time)
0,02 %0,10 %Ni in steel (5s meas time)
0,10 %Not possibleSi in Copper (60s meas. time)
0,25 %Not possibleMg in Aluminum (60s meas. time)
Detection limit examples
1s5s304/321 sorting
1s2s304/316 sorting
1s5sGeneral alloy identific.
10sNot possible1% Si in Copper
Analysis speed examples (required measurement time)
Mg - UTi - UElement range
SDDPentaPIN Detector
45kV40kVX-ray tube
X-MET5100X-MET5000
Alloys
Fast and accurate verification of critical materials (PMI) on different industries
X-MET5100 and X-MET5000 enable accurate and faster verification of critical materials in the PMI testing process along the whole metal manufacturing supply chain -
• inspection of incoming goods• testing during production and• manufacturing of goods
Important tool in routine maintenance when building up a power plantor petrochemical plant
Field conditions are tough on PMI tools!
• An analyzer must be able to measure the alloying elements at very low concentrations (e.g. Ti in stainless steels at the level of 0.05%)
• Material range is often very wide .• The analyzer must be robust and easy to use• Fast, accurate results are a pre-requisite• For most applications calibration of the unit must be traceable• For these reasons EDXRF is the preferred measurement
technique when carbon or boron measurement is not required
OI has now the range of highly productive mobile testing tools for these specific needs of both PMI inspectors and scrap sorters.
uJjbqRNMM - New PMI applications for hand-held analysis
• X-MET5100 elemental detection limits enable ppm level analysis in just 10 seconds
• This level of performance improves productivity and opens up new applications for hand-held analysis
• X-MET5100 can rapidly perform challenging trace element analysis such as
• FAC inspection (Cr in low alloy steels) in the nuclear power industry and
• QC of microalloyed steels used in the automotive industry.
X-MET5100 - Revolutionary Light Element analysis without vacuum or helium bottles• X-MET5100 provides fast, highly accurate laboratory quality
chemical analysis of Aluminum and Titanium alloys
• It reliably analyzes Light Elements such as silicon and phosphorus from copper, nickel and steel alloys
• Powerful Light Element capability combined with the non-destructive nature of the XRF technique makes X-MET5100 an invaluable tool or the aerospace industry where often finished or sensitive samples need to be analyzed
• The efficient Light Element capability provides added confidence for accurately identify nickel and copper alloys which may contain large amounts of aluminum and silicon.
X-MET5100 - Light Element AnalysisTypical examples where light element capability brings most value:
• Separation of cast and wrought aluminium alloys (based on the Si content)
• Identification of 5000 series alloys (based on Mg content) in marine and automotive applications
• Distinguishing 4000 series from the 1000, 5000 or 6061 alloys (based on Si content)
• Distinguishing titanium alloys which are differentiated by their aluminium content
• Ensuring correct Cu analysis and ID for Al/Si bronzes (Bronzes may contain up to 6% Si and 12% Al)
• Ensuring correct Ni content for Al containing Nickels (Ni alloys such as Monel K500, Inco 713, Inco 730 contain up to 6% Al
Measured Light Elements:• Aluminum LE: Mg, Al, Si• Titanium LE: Al• Copper LE: Al, Si, P• Nickel LE: Al, Si• Stainless LE: Si, S• Low Alloy LE: Si, P, S
Universal standardless FP calibration for alloys (Mg-U)
General limitations of the light element analysis:• Thin 4µm protective window needs to be used, which is more fragile
than standard 25µm Kapton® window• Accurate light element analysis requires flat and clean sample surface,
this may restrict the use in applications like scrap sorting
The analyzer of choice in allconditions, on-site or in-field • The material to be inspected can be difficult to access
(e.g. a refinery platform)• X-METs are battery operated, compact, robust and withstands harsh use
• The material to be inspected can be hot (e.g. like a tube in a power plant)• Integrated heat shield allows the measurement of hot test piece surfaces
for extended periods - up to 400°C / 750°F - X-MET5000 (X-MET5100 thick window version only, light elements then not available)
• The weld material often needs to be verified from narrow seam (material around the seam must be excluded)• X-METs enable the analysis of narrow weld seams down
to 2 mm
Analyze large or small samples structures like bolts, thin tubes or honeycomb in seconds – just point and shoot
• X-MET compensates for the shape of sample• Inspect pipes and welds for corrosion resistance
and pressure equipment for alloy composition• Wires of less than 1mm in diameter can be
identified in seconds• Avoid material mix-ups• High speed averaging function – up to 50
successive measurements for fast effortless batch evaluation
• A practically unlimited number of grades can be stored in the analyzer
• Recording of results can be automated if required
• Results can be read by a PC • An unlimited number of results can be
stored for further processing
Positive Material Identification
PMI Cannot be Easier
1) Name your sample2) Measure it3) Produce the PMI report
Rugged, reliable and durable tool
• IP54 (NEMA 3) approved. Superior dust and moisture protection
• High-strength environmentally sealed housing
• Withstands all weather conditionsfrom -10°C to +50°C and rough treatment
• Minimal service costs and down time
• CE, cCSAus certified
• 2 year Instrument warranty; including X-ray tube, excluding consumables Certified
IP54 (NEMA) splash
and dustproof!
Safety is the highest priority
Radiation Safety:•Password protection•Failsafe warning lights• IR proximity sensor•Count rate sensor
PDA based technology forflexibility and simplicity
PDA = Personal Digital Assistant
• Bright color touch screen display visible in any lighting condition
• Easy-to-use menu system• Full Microsoft Windows® compatibility• Memory card for easy data transfer and
back-up (no additional software necessary)
• Data transfer via supplied USB cable or wirelessly by WiFi or Bluetooth®
Computer
• HP PDA with Windows® Mobile 5.0• Key locked to prevent unintended
removal• 128 MB Internal memory• Min. 1 GB Removable memory• Capable of holding > 100,000 results
and spectra
• Results and spectra can be stored on a SD memory card
• Recording of results can be automated if desired
• Data can be downloaded to a PC using either
• Memory card reader (Standard accessory)
• Microsoft Active Sync over the USB cable
• Wirelessly, using the built-in Bluetooth capability
• Practically unlimited number of results can be stored for future processing
• PC Report Generator for easy and versatile formatting of final QC reports available
• Microsoft Excel and Access can be used to store and process the data and to generate custom reports
Easy reporting - time saving and trouble-free
Long battery life
• Rechargeable, removable inside handle• Li-Ion batteries (Quantity 2)• Typical duty cycle: 5-6 hours of operation
each• 110/230V 50/60 Hz battery charger,
including AC adaptor
• Intuitive user interface makes it possible to learn basic functions in a few minutes
• Minimal training is required
• Our network of specialists is ready to provide training for the more advanced features of the analyzer
Short learning curve
X-ray tube for optimized performance and maximum safety
*) Subject to local laws and regulations
Proprietary miniature X-ray tubeNo isotope means• Non-regulated shipping• No leak testing required• Easy, low cost disposal • Low cost registration
(varies by region)
Three modes of operationEmpirical Assay Calibration mode produces fast, accurate analysis even at low concentrations. Traceable reference standards establish the calibration.
Fundamental Parameters (FP) is a universal standardless calibration where practically any combination of physically measurable element can be analyzed with good accuracy. FP can measure up to 30 elementsbetween Mg-U (X-MET5100) and Ti-U (X-MET5000) regardless of concentration.
PASS/FAIL mode offers a convenient, fast way to sort material e.g. during delivery inspection
These three modes run smoothly together even when the user has no information about the material’s composition.
NOP
Typical Display
Sample name
Standard deviation
Analysis method
Screening method
Analysis result
Grade information
User interface in >10 languages
• User Interface is available in:• English• French• German• Italian• Japanese• Korean• Polish • Portugese• Russian• Simplified Chinese• Traditional Chinese• User customizeable language
Extensive and open grade library
• Nickel Alloys• Stainless Steels• Low Alloy Steel• Tool Steels• Cobalt Alloys• Copper Alloys• Titanium Alloys• Zirconium Alloys• Aluminum Alloys
• The X-MET is capable of storing thousands of grade identifications
• Easy to add new alloys and to create a custom grade library
• The precision of the grades can be adjusted to prevent false alarms which may occur during short measurement times
As standard X-MET5000 and X-MET5100 has an integrated grade library containing:
Easy editing of the grade tables
Easy • modification of the grade library• addition of new alloys• renaming of alloys
• In addition, the precision of the grades can be adjusted to prevent false alarms which may occur during short measurement times
Optional Software
• Empirical Calibration – enables user to create a calibration from a set of standards for unique applications. Also allows data acquisition and analysis using a PC. Enables viewing and analysis of samples spectra on a user’s PC.
• PC Report Generator - enables the creation of specific reports containing user selected information and format
Delivered as “turn-key” analysis tool
• Each delivery includes a calibration certificate• Instrument performance is
guaranteed by measuring alloy specific check samples(provided with each instrument)
• Calibrations can be customized usinge-mail
• It is not necessary to send the unit to the factory for calibration