tv manual.pdf

7/23/2019 tv manual.pdf

1/28

Please READ this manual carefully beforeoperating your TV, and retain it for futurereference.

OWNERS MANUAL

LED-LCD TELEVISION

LE32A300/LE42A300/LE55A300

LB32R3A/LB42R3A/LB46R3A/LB55R3A

LE32H300/LE42H300/L32K3/L42K3


2/28


3/28

Warning

LED -LCD television Owners Manual 3

WARNING!WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTSINSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

* To avoid electric hazards, it is strongly suggested that the back cover not be opened, as there is no any

accessory inside the casing.* lf necessary, please contact authorized after-sales services.* A lighting ash mark in a triangle: A potentially hazardous situation, which, if not avoided, could result in

serious injury by high voltage.* An exclamation mark in a triangle: Major part or accessory of which technical speci cations must be followed if

it is to be replaced.

RISK ELECTRIC SHOCK DO NOT OPEN

WARNING: To avoid fire or electric hazards, never place your television receiver in an area with heavymoisture. Attention should be paid to avoid accidental scratches or impacts onto the screen.

CAUTION: Please read this manual carefully before using your television and keep this manual in agood place for future reference.

To achieve the best performance of your television, read this Users Manual carefully andproperly store it for future reference.

Information of screen displays and figures in the Users Manual may vary due to technicalinnovations.

CAUTION: Unauthorized disassembly of this product is prohibited.

Warning


4/28

Important Safety Instructions

4 LED -LCD television Owners Manual



5/28




6/28

Panel Control


- This is a simplified representation of front panel.- Here shown may be somewhat different from your TV.

Panel Control

Introduction

1 TV/AV Press this key to open/close signal source optionsmenu.

2 MENU Menu display. Press to access the on-screenmenu display.

3 VOL +/- Press to adjust the volume. In theMENU screen,

these buttons serve as right/left buttons.

4 CH +/-

Press to scan through channels. To scan quicklythrough channels, press and hold down either+/- . In theMENU screen, these buttons serve asup/down buttons.

5 POWER Press to turn on and off the TV.

6 USB jack Connect a USB ash drive to view videos,imagesor listen music.

7 Mini USBConnect a USB ash drive to view videos,imagesor listen music.

8 SPDIF Digital Audio Optical output.

9 AV OUTConnect the audio L/R and video cables to yourother video equipment.

0 ANT INConnect cable pr antenna signal to the TV, eitherdirectly or through your cable box.

A AV1 IN Connect the video signal from a video device.

B HDMI INConnect a HDMI device to receive digital audioand uncompressed digital video.

C S-VIDEOConnect the S-VIDEO cable from an external signalsource to this jack.

D Headphone Headphone audio output terminal.


7/28

Connection Options


H D M I 3 I N

COMPONENT / AV2 IN

Y / VIDEO P b P r L - AUDIO - R

PC IN

PC/DVI AUDIOPC

DSMB

2

1

Y Pb Pr L RAUDIO

PC

A V 2 I N

C O M P O N E N T I N

A N T I N

H D M I 3

I N

P C

I N

A V O U T

VIDEO L RAUDIO

PC/DVI AUDIO

VIDEO L RAUDIO

Connection Options

Back panel connections

1 PC Video InConnect a video cable from a computer to this jack..

2 PC/DVI AudioIn

Connect the audio L/R cables from a computerto this jack.

3 ComponentVideo In

Connect a component video device to these jacks.

4 AV2 In Connect the video signal from a video device.

5 DSMB Mo-Box jack .

6 ANT InConnect cable pr antenna signal to the TV, eitherdirectly or through your cable box.

7 HDMI 3 INConnect a HDMI device to receive digital audioand uncompressed digital video.

8 AV OUTConnect the audio L/R and video cables to yourother video equipment.


8/28

Remote Control

8 LED-LCD television Owners Manual

Remote ControlBattery loading1. Slide open the cover of the battery compartment onthe back of the remote controller.2. Load two 7# (AAA) alkaline batteries in thecompartment, (plus and minus poles to respective mark)3. Replace the cover of the battery compartment.

PrecautionsAs strong light may interfere the signals, change yourposition to operate the remote controller if the televisioncannot be turned on or off as you expect.

Keep the remote controller away from heat source orhumid area to ensure effective performance of theremote controller.

Make sure that two AAA alkaline batteries are loaded. The batteries must be of the same type. The batteriesmust be located properly. The batteries are notrechargeable.

Make sure that there is no obstacle between the remotecontroller and television set.


9/28

Remote Control Function


- The remote control cannot be operated unless the batteries are properly loaded.- When using the remote control, aim it at the remote control sensor on the TV.

Function introduction

1 POWER Press this key to start TV from standby mode, press it again to return to standbymode.

2 USB Press this key for quick switching of streaming media.3 H. LOCK Refer to the Functional Description onPage 20.4 SOURCE Press this key to open/close signal source options menu.5 DSMB Press this key for quick switching of MO-Car.

6 STILLPress this key to freeze the image. Press it again to return to normal screen. (Note:Do not display a still picture for a long time to prevent the screen from burns.).

7 ARC Press this key to select the screen display propor tion.

8 MUTEPress this key to mute the sound, press it again to ac tivate the sound. The soundmay be activated by turning the TV on again or increasing the volume.

9 0-9 These keys are used to select a channel.0 Q. VIEW Press this key to return to the previous TV program(only work in the TV mode).A VOL+ /- Used to adjust the volume when the screen menu is c losed.

B CH+/-Used to select a TV channel when the screen options menu is closed, speci cally,press P to decrease the channel and press Pto increase the channel..

C Sound Mode Press this key continuously to select the sound mode.D Picture Mode Press this key continuously to select the picture mode.E TV.MENU Press this key to display or exit the main menu.

F D.MENU Press this key to display the Special Function Menu (it functions when specialmodules are inserted).

G THUMBSTICK (Up/ Down/Left/Right)

Allows you to navigate the on-screen menus and adjust the system settings toyour preference.

H OK Press this key to con rm the selection.I EXIT Clears all on-screen displays and returns to TV viewing from any menu.

J USB

Control the USB System.

Backward Forward Play/Pause BACK: Back REC: no availableZOOM: Press to magnify/minify an image D.CALL: Press to display programinformation.

K TV.CALL Display on/off.L TIMESHIFT No available.M VOD No available.N AUDIO No available.O PAGE+ No available.P GUIDE No available.Q TV/FM No available.R INFO No available.S PAGE- No available.T CH.LIST No available.U FAV Press this key to display the favorite program list menu.V STOCK No available.W SLEEP Displaying the sleep time.X INTERACTION No available.Y Fn No available.Z DDS No available.[ BUSINESS No available.\ GAME No available.

Remote Control Function


10/28

External Equipment Connections


Antenna Connection- Antenna or Cable Service without a Cable Box Connections.- For optimum picture quality, adjust antenna direction if needed.

Note:

* It is recommended that you'd better use 75 coaxial cable to removethe disturbance caused by airwave.

* Don't bind antenna cable and electric wire together.

To improve picture quality in a poor signal area,purchase and install a signal amplifier.If the antenna needs to be split for two Tvs, install a"2-WaySignal Splitter" in the connections.If the antenna is not installed properly, contact yourdealer for assistance.

NoteAll cables shown are not included with the TV.

ANT .



11/28



Choose Your Connection There are several ways to connect your television,depending on the components you want to connectand the quality of the signal you want to achieve. Thefollowing are examples of someways to connect your TV. Take LE32A300 as an example, Choose the connectionwhich is best for you.

VCR Connection

To avoid picture noise (interference), leave an adequate

select the source, press the OK button to confirm.

External AV Source Setup

How to connect

Connect the audio and video cables from the

external equipments output jacks to the TV input jacks, as shown in the figure.

When connecting the TV to external equipment,

match the jack colors (Video = yellow, Audio Left =white, and Audio Right = red).

H D M I 3 I N

COMPONENT/ AV2IN

Y/ VIDEO P b Pr L - AU DI O- R

PCIN

PC/DVIAUDIOPC

DSMB

H D M I 2 I N

A N T I N

H D M I 1 I N

A V 1 I N

V I D E O

L

R

- A U D I O

-

How to use

Select the input source with using theA SOURCE button on the remote control.

PressB / button to select the desired source.

PressC OK button to confirm.

Operate the corresponding external equipment.D

Connecting a DVD player

How to connect

Connect the DVD video outputs (Y, PA b /Cb , Pr /Cr)to the COMPONENT (Y, Pb /Cb , Pr /Cr) input jacks onthe TV and connect the DVD audio outputs to theAUDIO jacks on the TV as shown in the figure.

distance between the VCR and TV.

H D M I 2 I N

A N T I N

M i n i U S B

H D M I 1 I N

A V 1 I N

V I D E O

L

R

- A U D I O

-

A V O U T

L

V I D E O

A U D I O R

S P D I F

U S B

Connection Option 1Set VCR output switch to channel 3 or 4 and then tunethe TV to the same channel number.

Connection Option 2

Connect the audio and video cables from the VCRsAoutput jacks to the TV input jacks, as shown in thefigure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, andAudio Right = red).

Insert a video tape into the VCR and pressB PLAY onthe VCR. (Refer to the VCR owners manual.)

Select the input source with using theC SOURCE buttonon the remote control, and then press / button to


12/28


13/28



H D M I 3 I N

COMPONENT/ AV2IN

Y/ VIDEO P b P r L - AU DI O- R

DSMBPCIN

PC/DVIAUDIOPC

Note

Avoid keeping a fixed image on the TVs screen foralong period of Time. The fixed image may becomepermanently imprinted on the screen.

The synchronization input form for Horizontal andVertical frequencies is separate.

To obtain the best picture, do not play the USB,YPbPr, HDMI or PC source at the same time.

Monitor Out Setup The TV has a special signal output capability whichallows you to hook up a second TV or monitor.

Connect the second TV or monitor to the TVs AV OUTby the tie line. See the Operating Manual of the second TV or monitor for further details regarding that devicesinput settings.

A N T I N

M i n i

U S B

A V O U T

L

V I D E O

A U D I O R

S P D I F

U S B

Note

Component, PC, HDMI input sources cannot beused for Monitor out.

When connecting with external audio equipments,such as amplifiers or speakers, please turn the TVspeakers off.

Power sourceTO USE AC POWER SOURCE Use the AC polarized line cord provided for operation onAC. Insert the AC cord plug into a standard polarized ACoutlet.

Note

Never connect the AC line cord plug to other thanthe specified voltage. Use the attached power cordonly.

If the polarized AC cord does not fit into a nonpolarized AC outlet, do not attempt to file or cutthe blade. It is the users responsibility to have anelectrician replace the obsolete outlet.

If you cause a static discharge when touching theunit and the unit fails to function, simply unplug

the unit from the AC outlet and plug it back in. Theunit should return to normal operation. PolarizedAC Cord Plug.


14/28

Basic Receiving and Playing Operations


Playing OperationsSwitching ON/OFF the TV setIn the manual, the OSD (on screen display) may bedifferent from your TVs because it is just an example tohelp you with the TV operation.

Switching ON/OFF the TV set

First, connect power cord correctly and the powerAindicator will light.

PressB POWER on the remote control again.

If you want to exchange to standing by status,Cplease press down POWER on the remote control

Disconnect the power supply or unplug theDtelevision if it is intended to completely cease thetelevision performance.

Choose the Menu LanguageWhen you satisfied with your set for the first time,you must select the language which will be used fordisplaying menus and indications.

PressA MENU and / to select Function menu.

PressB / button to select language option.

Select a particular language by pressingC OK repeatedly.

When you satisfied with your choice, pressD MENU toreturn to normal viewing.

Choose the Input source

Change the picture source so you can watch your TV,VCR, Cable , or any other devices that are connected toyour TV.

PressA SOURCE button to enter the Input Sourcemenu and then use / button to select thedesired items (TV, AV1, AV2, Component, PC, HDMI1,HDMI2, HDMI3, Multimedia).

PressB OK button to confirm .

Picture Menu

The TV menu gives you an overview of the menus youcan select.

Note

Depending on the input signal, one or more menuitems may not be selectable.

How to select picture mode

The picture mode provides the pre-defined imagessettings: Standard, Mild, User, Dynamic and EyeGuard.

You can pressP.MODE button on the remote controlto select the option Standard, Mild, User, Dynamic andEyeGuard.

Basic Receiving andPlaying Operations


15/28



How to customize your own picture status

PressA MENU button and then use / button toselect Picture menu.

PressB / button to select the desired items.,press OK to enter its submenu.

PressC / button to adjust the setting.

Contrast This will adjust the intensity of bright parts in thepicture but keep the dark parts unchanged.

Brightness This will adjust the light output of the completepicture, which will mainly affect the darker areas ofthe picture.

Color This will adjust the saturation level of the colors to suityour personal preference.

Sharpness This will adjust the sharpness of fine details in thepicture.

Note

The picture options can only be adjusted in theUser mode. The other picture modes are preset.

TintAllows you to select the color mix (Tint) of the picture.

Backlight

press / to adjust the backlight(0--------10).

3D_DIMSelect the 3D-DIM Demo or 3D-DIM Calibration, PressOK to set.

Palette:Press / to select the Palette option, and thenpress OK to enter its submenu, and finally press

/ to select a toner pattern from six patterns(Cool2, Cool1, Standard, Warm1, Warm2, User) to yourcolor preference. Normally, the Standard mode isselected.If the User mode is selected, press / to enterthe palette menu, (as shown in the below f igure),and then press / to select a benchmark in therange of 2500K~15000K from warm color to coldcolor, afterwards press / to adjust; if a differentbenchmark is selected for adjustment, the originaladjustment data will be automatically cleared.

Picture

Sound

Channel

Function

Adjust

Timer

Language Menu Time out

Programe. Auto Tun. Exchange

Volume Balance Digital SRS AVL MAXX Bass Reset

Current.. Off Time Off Time On Channel Remind T.. Remind C..

Image Po.. Horizont Wertical. Auto.. Clock Phase Reset

Picture MEMC DSM Background OPC Eye Guard ResetOptimize Mode

ResetPress / to select OK or Cancel.

Sound menuHow to select sound mode

PressA MENU button and then use / button toselect Sound menu.

PressB / button to select Digital tone Mode.press OK to enter its submenu.

PressC / button to select the option Standard,Music, Movie and User.


16/28



You can also press S.MODE button on the remotecontrol to select the Audio Mode: Standard,Music, Movie and User.

How to Customize your own soundstatus

PressA MENU button and then use / button toselect Sound menu.

PressB / button to select the desired items,press OK to enter its submenu.

PressC / button to adjust the setting.

VolumePress / to adjust the volume of a TV Program.

Balance This will adjust the output of the right and leftspeakers to obtain the best stereo reproduction foryour listening position.

The intermediate value is 0. When indication valueof Balance increases toward 50, sound of the rightand left speakers becomes stronger and weaker,respectively. When indication value of Balancedecreases toward -50, sound of the right and leftspeakers becomes weaker and stronger.

Digital toneThis select the modes for sound reproduction dependenton the broadcast signals or signals from external inputsreceived.Select the mode of sound (User/Standard/Music/Movie).If the User mode is selected, press / to selecta benchmark in the range of 50~15K from bass totreble, afterwards press / to adjust, if a differentbenchmark is selected for adjustment, the originaladjustment data will be automatically cleared.

Surround

The surround sound feature expands the audiolistening field wider and deeper to create exceptionalsound quality from the TVs speakers.

AVL (Automatic Volume Limit) This will reduces the differences in volume levelamong broadcasters.

Woofer To adjust the super bass. Press / to select superbass off, low , high or Middle.

Reset

Return to factory default settings.

Channel menuDisplay channel menu by pressing SOURCE button thenuse / button to select the source of TV item.

PressA MENU button and then use / button toselect Channel menu.

PressB / button to select the desired items,press OK to enter its submenu.

Programme Edit

You can add a label to a channel to make it easier to nd.


PressB / button to select the Programme Edit ,and then press OK to enter submenu .


17/28



Manual SearchPress / to select the Search option, and finallypress / to start manual search. Upon finding aprogram, the search will automatically stop, and theprogram will be stored onto the current channel.You may stop the search by pressing OK or MENU.

Fine TunePress / to select the Fine Tune option, andthen press / to start UP or DOWN fine tuninguntil obtaining a relatively good picture effect. Thefine tuning function is for the purpose of improvingpicture effect through fine tuning when that of acertain program is not good enough. Normally, theoptimal picture effect can be obtained without finetuning when watching TV programs, and fine tuning

is to meet the need of adjusting a certain program.

Color systemPress / to select the Color Systems option,and then press / to select correct colorsystem. The TV is des igned with three systems for yourchoice, i.e. Auto, PAL , SECAM and NTSC. Generally,the system is set as Auto and it is not necessary tomake an adjustment. The system is normally set asAuto during auto search.

Sound system

The TV is des igned with four systems for yourchoice, i.e. DK, M, BG and I. Generally, it is notnecessary to adjust the system. The system isnormally set as DK during auto search.

SkipWhen the skip is set ON, the channel will beskipped when pressing CH or CH and only canbe selected by pressing 0-9 numerical keys.

If you want to recover the skipped channel

1. Use Direct-digit Choosing button to select thenumber of the channel to be recovered.

2. Do the above steps again.3. Press / to set Skip as Off.

Auto Tuning


PressB / button to select Auto Tuning , thenpress OK the menu opens.

PressC / button to select OK, press OK button onthe remote to start to scan. Press MENU button to

return to the previous menu, press EXIT button toEXIT the menu screen.

All channels now available will be automatically preset inorder .After the search has nished, the rst program

number will display on the screen.

This search automatically adds only the active channelsin your area to the TV's memory.

It deletes any channels on which there is no broadcast ora poor signal.

The channels found are automatically saved.

Exchange

PressA MENU on the remote control unit or MENU onthe TVs front panel to display main menu, and thenpress / to select Channel menu.

PressB / to select the Prog. Exchange option,and then press OK to enter its submenu.

PressC / to select the To Channel option, andthen press / to set the found to be exchanged to.


18/28



After adjusting the current channel and the found toDbe exchanged to, press / to move the cursorto the Exchange option, and then press OK to startexchange and exchange the program on currentchannel to the channel you set for exchange.

Function Menu

Function Menu Set

PressA MENU on the remote control unit or MENU on the TVs front panel to display the main menu, andthen press / to select the Function menu.

PressB / to select the option to be adjusted,and then press / to adjust it.

Language Two languages (i.e. Simplified Chinese and English)are available for your choice.

Menu Timeout The option is for adjusting the menu display time.Press / to set the desired time (5-15s).

Picture Optimize

Press / to select the Picture Optimize option.

Press

OK to enter the submenu.Press / to select theDCDI/ColorManagement to be adjusted, and then press

/ to select ON or OFF.Press / to select the DNR to be adjusted, andthen press / to select Low/Middle/High/ Off.

MEMCPress / to set ON, Demo1,Demo2 or OFF, themoving picture will be better when MEMC is onfunction. (This function is only available for LE55A300/LB55R3)

DSMPress / to select DEMO OFF, DEMO1, DEMO2,DEMO3.

BlackgroundPress / to set ON or OFF, if you select ON, the TVscreen will be blue if no signals are available.

OPCPress / to select the OPC , then press OKand / to select Uesr/Dynamic/Daylight/Normnal/Night.Press / to select the Adjust , then press / to set 0-10.Press / to select theDynamic Contral to beadjusted, and then press / to select ON orOFF.

Eye guard ModePress / to select the Eye guard Mode option.Press OK to enter the submenu.Press / to select the Power E.G.Mode , then press

/ to select Standard/Eye Guard/Curtain.Press / to select the Change Ch.E.GI/Watching E.G/Watching E.G.Delay to be adjusted,and then press / to select ON or OFF.


19/28



ResetPress / to select OK or Cancel which with Doyou want to reset option values.

Adjust MenuThe TV can be used as a display, and you may adjustrelevant settings. Press SOURCE to switch the signalinput to PC mode.

PressA MENU to display the screen main menu, andthen press / to select the Adjust menu asshown in the below figure.

On Time

PressB / to select the option to be adjusted.

PressC / to adjust it.

Image Position This is used to adjusting H-Position and V-Position.

H-SizeHorizontal size of picture can be adjusted in this item.

V-SizeVertical size of picture can be adjusted in this item.

Auto AdjustVertical and Horizontal position of picture can beadjusted in this item.

Clock

This is used for adjusting the phase of pixel clock in PCmode.

Phase This is used for adjusting H Position and V Position aswell as relative parameters in PC modes.

ResetReturn to factory default settings.

Time MenuPressA MENU button and then use / button to

select Time menu.PressB / to select the desired option, press OK toenter its submenu.

Current Time : The current time is calculated from themoment upon turning the TV on. At first, check whetherthe time indicated on the TV's clock is consistent with thestandard time of your time zone; if not, adjust the clock asfollows:

Press MENU on the remote control unit or MENU on the TVs front panel to display the main menu,and then press / to select the Timer menu,afterwards press / to select the Current Timeoption, press OK to enter the submenu.Press / to set hour and minute.

Press / to adjust the time.After finishing time setting, press OK or MENU toconfirm.

Off Time/On Time : Set a time for the TV to turn off oron.This function allows the TV to automatically turn on orenter standby mode upon reaching the preset time.

Press OK to enter the setting screen, and then

press / to select ON or OFF, if you select ON,press / to set hour and minute. ON indicates


20/28



the On/Off Time function is enabled while OFFindicates the function is disabled.. After finishing time setting, pressOK or MENU toconfirm.

Note

After setting the On/Off Time function, if the TV is ACoff or forcible DC off, the function will be automaticallycleared.

On channel : This function is used in combination withthe On/Off Time function. When the TV turns on uponreaching the On time, it automatically enters the presetchannel.

Press OK rst and then press / to set the OnChannel or OFF.

Remind Time/Remind channel : The remind time andremind channel functions allow the TV to automaticallyenter the preset channel at preset time. If the TV is AC offor forcible DC off, the preset time will be cleared.

Press MENU on the remote control unit or MENU on the TV's front panel to display the main menu,

and then press / to select the Timer menu,afterwards press / to select the Remind Time option.Press OK to enter the setting screen, and then

press / to select ON or OFF, if you select ON,press / to set hour and minute, and thenpress / to adjust time.After finishing time setting, press OK or MENU toconfirmPress / to select the Remind Channeloption, and press OK rst and then press / to set the found .

Lock SetupThe television has the function of security default lock.Password needs to be entered when the program lockmode is to be set.

How to use the password function

Press H. LOCK, the TV screen will display Enter Passwordto prompt the user to enter password by pressingcorresponding numerical keys; if the password is correct,the user enters the Lock Set menu; if incorrect, the user isrequired to enter a password again.

If there is no operation for a few seconds, the display willautomatically disappear.

The Lock Set menu is as follows:

Change Password OK

Tuning Lock

Preset Source

Preset Prog

Source Lock OK

Child Lock

Max Volume 100

Power On Volume off

Unlock OK

off

off

off

off

Lock Set

Change PasswordAfter entering the Lock Set menu, press / toselect the Change Password option, and then pressOK to display the Change Password menu, afterwardsenter a new 4-digit password by pressing numericalkeys and repeat entering this password once again.If the user does not want to change the password inhalfway, he may press MENU to exit from this menu.

Note The initial password is 0000, and the password settingwill not be changed after executing the Unlockoption.

Tuning Lock Press / to select the Tuning Lock option, andthen press / to set ON or OFF.(If set ON, the Tuning Menu is not available in TVmode. To make any operation related to the TuningMenu, it need to enter the Lock Set menu to set Tuning Lock OFF or execute the Unlock option.)

Preset Source SettingPreset Source may be set as Off, TV, AV,Component,HDMI, PC and USB. When the Preset Source is set as TV, after entering the Preset Channel menu, press

/ to select the preset channel, and the channelwill be forcibly switched to the preset one uponturning the TV on; when the Preset Source is set asother signal sources, the TV will be forcibly switched tothe preset source upon turning on. For example, whenthe Preset Source is set as YPbPr /YCbCr, the TV will beswitched to YPbPr /YCbCr upon turning on; when set asOFF, the preset funct ion will be closed.

Preset Prog


21/28



Only when the Preset Source is set as TV can thePreset Channel option be available. Press / toselect preset channels from 0-254.

Source Lock This function is used to prohibit watching a programfrom various external inputs, e.g. AV and PC, etc. Press

/ to select a certain option, and then press OK to enter the submenu, press / to set an externalinput lock ON or OFF. If an external input lock is setON, after entering this mode, the screen will displayblue background with muting and a prompt SourceLock; during Source Lock prompt, Source Lock willremain if there is no other display on the screen. Towatch a program from a locked external input, justenter Source Lock submenu to set correspondingstatus as OFF or execute the Unlock option in the LockSet menu.

Child Lock SettingPress / to select the Child Lock option, and thenpress / to set ON or OFF. If set ON, this controlkey will not respond, and the screen will display ChildLock when the key is pressed; if no other operation ismade, the display will automatically disappear later. To resume Child Lock function, just enter the Lock Setmenu to set Child Lock OFF or execute the Unlockoption.

Max Volume SettingPress / to select the Max Volume option, andthen press / to freely adjust the max volumewithin the range of 0~100. After finishing the setting,the max volume in the Volume menu will not exceedthe preset max volume; for example, if the presetmax volume is 30, the volume in the Volume menucan not be increased any longer upon reaching 30;if the preset max volume is less than the value in theVolume menu, the latter will decrease along with thedecrease of preset max volume.

Power on VolumePress / to select the Power on Volume option,

and then press / to freely adjust the volumewithin the range of 0~100.

Unlock SettingPress / to select the Unlock option, and thenpress OK to clear all the lock settings, namely set allthe lock setting options as OFF; the Preset Channelis set as OFF and max volume returns to 100 (exceptpassword).

Streaming Media PlayingSystem

Note

The diagrams in the following section areschematic and only for your reference. Please seethe actual product if necessary.

Supported file formats:APicture: *. JPEG; PNG; BMP;Music: *. Mp3(8-320kbps; WMA(32-192kbps);AAC(16-576kbps)

Movie:

MPEG4:*. avi files in accordance with Div*4. x/5. xProtocol;

MPEG2: some *. mpeg files;MPEG1:*. dat and some *. mpeg files;RealVideo Text: *. Txt.

Note

Due to the particularity of file coding, some filesmay be unable to be read.

Supported equipment:BSupport the equipment that supports Mass Storage

Protocol and whose file system is FAT/NTFS/FAT16/FAT32, such as some USB disks, mobile hard disks,card readers, MP3 players and digital cameras.If USB equipment could not be identified dueto unsupported file system, please format theequipment to the above-mentioned file system;

The external card reader supports most of the digitalCcards in the current market; the types of digital cardsthat can be read are relevant to the performanceof selected card reader; you may attach standardmobile hard disks (working voltage 5.0V, workingcurrent not higher than 500mA); during media

playing, do not pull out storage media, otherwise itmay cause system halt, damage the files in storagemedia or damage USB equipment; sometimes, the TV may halt due to overhigh information error rate,in which case you should restart the system; thereare a lot of nonstandard USB mobile equipmentin the market, they may not be identified whenconnected to the streaming media playing system;the above phenomena may also occur on computersand are not the TVs fault.


22/28



To achieve smooth playing, ensure the following:D

The file code rate should be lower than 300KB/S;

Due to the limitation of USB signal transmissiondistance, it is recommended not to use USB patchcord, in case of using the cord, make sure that itslength is not over 1m;Use high-speed USB equipment in conformitywith USB2.0 Interface Standard; if USB equipmentin conformity with USB1.1 Interface Standard isused, the playing may be unsmooth.

Although many movie files are with such postfixes asEavi and mpeg, actually there are several formats in thefiles; however, the TV can only play some files in aviand mpeg formats. Some files with the postfix "dat"are not movie files, but data files commonly used incomputers, and they can not be played as movies.

Start/Exit Streaming Media PlayingSystem

PressA USB on the remote control unit to select thestreaming media function.

Insert USB equipment into corresponding USBBinterface 2s after starting the system.

After entering the system menu, pressC / on

the remote control unit to select the required USBequipment, and then press / on the remotecontrol unit to select the required file.

PressD OK to enter the selected file.

To exit the streaming media playing system andEwatch a TV program, you must return to thestreaming media main menu at first (to protectequipment), and then press SOURCE to select TV ordirectly press USB to return to the TV mode.

Operating Method of StreamingMedia Menu

PressA / to scroll through main menu orsubmenu and select your desired option.

PressB OK to confirm your selection.

PressC REV/FWD to achieve the FF (fast forward) andFB (fast back) of the movie or music being played.

PressD PLAY/PAUSE to pause playing, and press itagain or press OK to continue playing.

PressE ZOOM to magnify pictures; in zoom mode,press / and / to move the picture.

PressF OK to display and press EXIT to exit the screendisplay information while playing.

PressG BACK to stop playing, or return to the previousmenu, and press BACK repeatedly to return to themain menu.

Playing a Picture

After entering USB main interface, pressA / toselect a harddisk partition, and then press / toselect the Picture option.

PressB OK to confirm the selection and enter thepicture playing interface.

PressC / to change page, and press / toselect the picture you want to play, and then pressOK to enter the playing display interface.

Press ZOOM to magnify the picture, and thenpress / / / T to move the picture.Press / to select the last or next picture.Press / to rotate the picture.


23/28



To exit playing, just pressD BACK repeatedly.

Playing a Movie

After entering USB main interface, pressA / toselect a harddisk partition, and then press / toselect the "Movie" option.

PressB OK to confirm the selection and enter themovie playing interface.

PressC / to change page, and press / toselect the movie you want to play, and then pressOK to enter the playing display interface.

Press / to select the last or next movie.

To exit playing, just pressD BACK repeatedly.

Note

The menu display varies with the number andnames of files in your equipment.

Playing Music

After entering USB main interface, pressA / toselect a harddisk partition, and then press / toselect the Music option.

PressB OK to confirm the selection and enter themusic playing interface.

PressC / to change page, and press / to

select the music you want to play, and then press OK

to play the music.

To exit music playing, just pressD BACK repeatedly.

Text

After entering USB main interface, pressA / toselect a harddisk partition, and then press / toselect the Text option.

PressB OK to confirm the selection and enter the textplaying interface.

PressC / / / to select the text you wantto read, and then press OK to play the text readinginterface. Press / to change page, and pressBACK to exit the reading interface.

To exit the Text mode, just pressD BACK repeatedly.

Settings

After entering USB main interface, pressA / toselect the Settings option.

PressB OK to confirm the selection and enter thesettings selection interface, and then press / to select the required options.


24/28

Maintenance/Troubleshooting


Photo Slide TimeSet the scan speed of pictures to be scanned in slideform. There are three options (Middle/Slow/fast). Press

/ to select the desired option.

Movie SubtitleSelect "ON" or "OFF".

Maintenance

MaintenanceEarly malfunctions can be prevented. Careful and regular

cleaning can extend the amount of time you will haveyour new TV. Be sure to turn the power off and unplugthe power cord before you begin any cleaning.

Cleaning the Screen

Heres a great way to keep the dust off your screenAfor a while. Wet a soft cloth in a mixture of lukewarmwater and a little fabric softener or dish washingdetergent. Wring the cloth until its almost dry, andthen use it to wipe the screen.

Make sure the excess water is off the screen, andB

then let it air-dry before you turn on your TV.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry,lint-free cloth. Please be sure not to use a wet cloth.

Extended Absence

If you expect to leave your TV dormant for a long time

(such as a vacation), its a good idea to unplug the powercord to protect against possible damage from lightningor power surges.

Troubleshooting

For the sake of time and cost, it is stronglyrecommended that you checkout the problem byyourself according to the instructions listed hereunderbefore contacting the after-sales service for technicalassistance.

Problem Possible remedies

Nopicture,no sound

Turn onthe power supply; Properlyplug theTV setto the powersocket;Check to see if the power cable of otherappliance is plugged in the TV set. Makesure that the power cable of the TV setis properly connected.

Problem Possible remedies

Goodpicture,no sound

Depress the volume button;Check out theaudio frequency input signals.

Failure ofremotecontroller

Check to see if the remote controllerdisplay receiving window are blocked

by other objects and if batteries areproperly loaded.

No color,weak coloror poorpicture

Designate the item of color from thePicture menu and depress the volumebutton; Keep the display and VCRseparate a reasonable space; Activatesome functions to store picturebrightness; Make sure that the displayand signal source are available andturned on.

Excessivebrightnessor darkness

Adjust brightness or contrast.

Picturetoo big orsmall

Adjust the setup of sizes.

Onespeakerfailure

Balance the sound in the menu.

Slightsoundfromdisplay

It is a normal phenomenon.


25/28

Speci cations/Format


NoteDo not leave the television with static picture in anextended period as it may result in residual imageon your television screen.

NoteProduction of the screen requires high and precisiontechnologies. However, there might be somedank or bright (red, blue or green) spots, or someanomalistic stripes or spots. This is not defect. If theTV set is used in an area 2,400 meters above the sealevel where the air pressure is below 750hpa, thepicture on the screen maybe affected and a muffledsound might be produced. These phenomenamight happen in the area 1,500 meters above thesea level. This is resulted from difference betweenair pressures inside and outside the display. This isnot a defect covered by the limited warranty.

SpecificationBasic specication and parameter

Power ~ 150-240V 50/60Hz

Color System PAL, SECAM,NTSC

Stand-byConsumption D/K, B/G, I, M

Video Input USB,AV, Component, HDMI or PC,

Environmentalcondition

Operating temperature range:+5C - +35C Operatinghumidity range: 20%-80%Storage Temperature:-15C~+45CStorage Humidity: 5%-90%,non-condensing

If the storage temperature islower than 0 C, please firstlays the machine aside afterin the operating temperatureenvironment carries on restores2 hours, then electrifies the useagain, protects your televisionnot to receive the damage.

Accessories

Owners manual x1Remote Control x1Alkaline battery x2(This is only available for certainmodels,please refer to actual products.)

Product main size (contain stand)

MODEL PowerConsumption Net Size(LxWxH)Net

Weight

LE32A300 60W 788x210x559mm 8.7Kg

LE42A300 110W 1019x265x705mm 19.5Kg

LE55A300 160W 1315x280x689mm 28.5KgLB32R3A 100W 796x230x590mm 11.8Kg

LB42R3A 160W 1020x290x724mm 27.5Kg

LB46R3A 180W 1122x330x789mm 29.0Kg

LB55R3A 300W 1328x365x895mm 39.0Kg

LE32H300 60W 782x160x557mm 10.8Kg

LE42H300 110W 1019x265x705mm 19.5Kg

L32K3 100W 798x230x575mm 12.6Kg

L42K3 160W 1021x290x704mm 20.5Kg

NoteDesign and specifications are subject to changewithout notice. The dimension in this manual is aapproximation.

FormatRecommendatory HDTV/SDTV(YP b P r /YC b Cr ) format

SequenceNumber Format

RefreshFrequency (Hz)

1 480i/480p 602 576i/576p 50

3 720p 50/60

4 1080i/1080p 50/60

Recommendation PC connectioninput format


26/28

Format


sequencenumber

Format H-Frequency(KHz)

V-Frequency

(Hz)1 640*480@60Hz 31.5 60

2 800*600@60Hz 37.88 60

3 1024*768@60Hz

(Recommendatory) 48.36 60

Recommendation DVI connectioninput format

SequenceNumber Resolution Refresh Frequency (Hz)

1 640*480 60

2 800*600 60

3 1024*768 60

Recommendation HDMIconnection input format

SequenceNumber Format Refresh Frequency (Hz)

1 480i/480p 60

2 576i/576p 50

3 720p 50/60

4 1080i/1080p 50/60


27/28


Maintenance / Troubleshooting/Speci cation


28/28

tv manual.pdf

Documents