tv lg 15la6r lcd service_manual

Click here to load reader

Post on 08-Apr-2015

320 views

Category:

Documents

7 download

Embed Size (px)

TRANSCRIPT

website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html

LCD TV SERVICE MANUALCHASSIS : ML-041B

MODEL: RM-15LA66KCAUTIONBEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CONTENTS

CONTENTS .............................................................................................. 2 PRODUCT SAFETY ..................................................................................3 SPECIFICATION ........................................................................................4 TIMING CHART........................................................................................11 ADJUSTMENT INSTRUCTION ...............................................................12 TROUBLE SHOOTING ............................................................................15 BLOCK DIAGRAM...................................................................................20 WIRING DIAGRAM ..................................................................................22 EXPLODED VIEW .................................................................................. 23 EXPLODED VIEW PARTS LIST ..............................................................24 REPLACEMENT PARTS LIST ............................................................... 25 SVC. SHEET ...............................................................................................

-2-

SAFETY PRECAUTIONSIMPORTANT SAFETY NOTICEMany electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General GuidanceAn isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

X-RAY RadiationWarning:The source of X-RAY RADIATION in this TV receiver is the High Voltage Section and the LCD PANEL. For continued X-RAY RADIATION protection, the replacement panel must be the same type panel as specified in the Replacement Parts List.

To determine the presence of high voltage, use an accurate high impedance HV meter. Adjust brightness, color, contrast controls to minimum. Measure the high voltage. The meter reading should indicate 23.5 1.5KV: 14-19 inch, 26 1.5KV: 19-21 inch, 29.0 1.5KV: 25-29 inch, 30.0 1.5KV: 32 inch If the meter indication is out of tolerance, immediate service and correction is required to prevent the possibility of premature component failure.

Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

AC Volt-meter

To Instrument's exposed METALLIC PARTS

0.15uF

Good Earth Ground such as WATER PIPE, CONDUIT etc.

1.5 Kohm/10W

SERVICING PRECAUTIONSCAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 F to 600 F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500 F to 600 F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuitboard printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500 F to 600 F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.

-4-

IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder. Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

-5-

SPECIFICATIONNOTE : Specifications and others are subject to change without notice for improvement.

1. Application rangeThis specification is applied to ML-041B chassis.

2. Requirement for TestTesting for standard of each part must be followed in below condition. (1) Temperature: 25C 2C (2) Humidity: 65% 10% (3) Power: Standard input voltage (AC 100-240V, 50/60Hz) (4) Measurement must be performed after heat-run more than 30min. (5) Adjusting standard for this chassis is followed a special standard.

3.General SpecificationNo. 1 Maker Type ActiveDisplay Area Pixel Pitch [mm] Electrical Interface Color Depth Size [mm] Surface Treatment Operating Mode Back light Unit R/T 2 Maker Type ActiveDisplay Area Pixel Pitch [mm] Electrical Interface Color Depth Size [mm] Surface Treatment Operating Mode Back light Unit R/T 3 Maker Type ActiveDisplay Area Pixel Pitch [mm] Electrical Interface Color Depth Size [mm] Surface Treatment Operating Mode Back light Unit R/T Typ. Typ. Typ. Item LPL TFT Color LCD Module 15.0 inches(380.16mm) diagonal(Aspect 4:3) 0.297mm(H)x0.297mm(V)xRGB LVDS 6BIT WITH FRC, 16,777,216 colors 332.8(H)x262.2(V)x18(D) Anti Glare(HAZE 3%), Hard Coating(3H) Normally Black, 4 CCFL(4 lamps) R.T.:10ms + F.T.:22ms (MAX) HYDIS TFT Color LCD Module 15.0 inches(380.16mm) diagona 0.297mm(H)x0.297mm(V)xRGB LVDS RGB 6-BIT 16,194,277Colors 331.6(H)x254.7(V)x12.7(D) HAZE25,Hard Coating, ANTI- Glare (3H) Normally Black 4 CCFL(4 lamps) T total(Tr+Td) = 25ms CMO TFT Color LCD Module 15.0 inches(380.16mm) diagona 0.304.1mm(H)x228.1mm(V)xRGB LVDS RGB 6-BIT 16,194,277Colors 331.6(H)x254.6(V)x13(D) Hard Coating, ANTI- Glare (3H) Normally WHITE 4 CCFL(4 lamps) R.T.:22ms + F.T.:38ms (MAX) CMO HYDIS Specification LPL Remark

-6-

4. Feature and FunctionNo. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Teletext REMOCON AV Input S-Vedio Input Component input PERI TV Connector RGB(VGA)Input H/p input PC Sound input RS-232 Discrete IR 2 Carrier Stereo NICAM Stereo 2 Carrier Dual NICAM Dual DW(Double Window) Mode MW(Multi Window) Mode Film Mode Noise Reduction Progressive Scan Motion Detection SRS WOW wivel Speaker Ez-pip ARC DRP DCDI HDCP Item Specification TOP, FLOF,LIST 10 page NEC Code 2 1 1 Full SCART : 1 1 1 1 YES NO BG, DK BG, I, LL' BG, DK BG, I, LL' X X O X O X X X X O O X X Rear (option,Commercial) Top(option) PAL/ NTSC Rear(option, NT), Rear Rear (option, NT) Rear (option,EU) D-sub 15 pin Remark

5.Optical CharacterNo. Item Specification LPL 1 2 3 4 Viewing Angle Luminance Contrast Ratio CIE Color Coordinates WHITE RED Green Blue WX WY Wr Yr Xg Yg Xb Yb Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. R/L, U/D Luminance(cd/ ) Variation 450 1.3 400 0.289 0.304 0.619 0.343 0.298 0.578 0.289 0.304 0.265 0.293 0.629 0.340 0.255 0.601 0.141 0.071 HYDIS 80/65 80/65 500 1.33 300 0.314 0.344 0.632 0.361 0.295 0.598 0.142 0.102 AUO 60/60 40/60 500 Typical MAX/MIN ALL white/All back Min =Typ.-0.03 Max =Typ.+0.03 Remark

6.Engineering Specification 6-1.General Specification(TV)No. 1 Item Video input applicable system Specification 1)PAL-D/K,B/G,I 2)NTSC-M 3)SECAM NTSC 4.43 2 Receivable broadcasting system 1)PAL/SECAM BG 2)PAL/SECAM DK 3)PAL I/I 4)SECAM L/L 5)NTSC M 6)PAL-N/M 7)NTSC M 3 RF input channel VHF : E2 ~ E12 UHF : E21 ~ E69 CATV : S1 ~ S20 HYPER : S21 ~ S41 L/L : B,C,D VHF : 2 ~ 13 UHF : 14 ~ 69 CATV : 1 ~ 125 VHF Low : 1~M10 VHF High : 4~S22 UHF : S23~62 4 5 6 7 Input voltage Tuning system Operting environment Storage environment AC 100 - 240V/ 50Hz,60HZ FVS 100 program FS 1)Temp : 0 ~ 40 deg 2)Humidity : 85% 3)Temp : -20 ~ 60 deg 4)Humidity : 85% PAL, 200PR.(Option) NTSC JAPAN NTSC FRANCE PAL 7)NTSC Area(RM) EU/Non-EU(RZ/RT) (PAL Market) Remark

-8-

No. 1

Item Power Supply Normal Stand By Suspend Mode DPM Off Mode Cut-off Switch off ITEM H/V Sync On/On Off/On On/Off Off/Off -

Specification Video Active Off Spectification 1: RED 3: Blue: 5: S.T(GND) 7: Green GND 9: N.C 11: ID0(GND) 13: H-Sync 15: SCL 1) Contrast/Brightness 2) H-Position/V-Position 2: Green 4: ID2(GND) 6: RED GND 8: Blue GND 10: D-GND 12: SDA 14: V-Sync Shell: GND Power Consumption 55W 1W 1W 1W 0W PBP SWAP ON/OFF

Remark LED Color GREEN RED OFF Remark

2

D-SUB Pin Configuraion

10: Digital GND

3

Control Function

3) Tracking : Clock/ Phase 4) Auto Configure RESET

4

Y, Pb, Pr

Middle east/ NTSC Area

1: Y 5 D4 Jack (525i, 525p, 750p, 1125i) 3: Pb 5: Pr 7: Line1 Ready 9: LINE2 11: LINE3 5) 13: Line3 Ready

2: Y GND 4: Pb GND 6: Pr GND 8: LINE1 10: Line2 Ready 12: SWITCH GND 6) 14: SWITCH JAPAN Only

6-2.PowerNO1 2 3 4 5 6 7 8 9 10 11

ItemAC Power Shut Down Voltage DC Voltage, Inverter DC Voltage, LCD Panel DC Voltage, Audio DC Voltage, Tuner(5) DC Voltage, Tuner(9) DC Voltage, Tuning(31) DC Voltage, VCTi(5) DC Voltage, VCTi(8) DC Voltage, VCTi(3.3) DC Voltage, VCTi(1.8) DC Voltage, GM2221 (3.3) DC Voltage, GM2221 (1.8) DC Voltage, Digital (3.3) DC Voltage, Digital (5)

Min90 22.8 11.4 14.0 4.5 8.5 31 4.5 7.5 3.1 1.6 3.1 1.6 2.8 4.5

Typ24 12 15 5 9 33 5 8 3.3 1.8 3.3 1.8 3.3 5

Max264 25.2 12.6 16.0 5.5 9.5 35 5.5 8.5 3.5 2.0 3.5 2.0 3.8 5.5

UnitV V V V V V V V V V V V V V V

Remark

Japan only

-9-

6-3. PowerNO1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.

ItemVideo Input Level Audio Input Level Audio Input Frequency Response Audio Input S/N Audio Input Distortion Audio Input Dynamic Range Video Output Level Video Output Frequency Response Video Output S/N Audio Output Level Audio Output Frequency Response Audio Output S/N Audio Output Distortion Video Input Level, R/G/B Video Input Level, Component(Y, PB, PR) RGB Input Resolution, Vertical RGB Input Resolution, Horizontal RGB Input Horizontal Frequency RGB Input Frame Rate

Min0.85 0.4 0.1 40 2 0.85 3.8 40 0.4 0.1 40 0.6 0.6

Typ1 0.5

Max1.15 0.6 7 2

UnitVpp V KHz DB % V Vpp MHz DB V KHz DB % Vpp Vpp Pixel Pixel KHz Hz

RemarkEN-50049 NTSC:0.4Vrms(Typ)

1

1.15

0.5

0.6 7 2 0.8 0.8

0.7 0.7 768 1280

75 ohm 75 ohm Only 20" See table 5-5 See table 5-5

640 Pixel 480

6-4. The OthersNO1 2 3 4 5 6

ItemSearch Sensitivity Soft Ware Functionality Test REMOCON Working Sensitivity, Straight REMOCON Working Sensitivity, T/B/L/R Closed Caption Sensitivity Teletext Sensitivity

Min

Typ

Max-85

UnitdBm

RemarkLGE Specification

0.1 0.1

10 9 -70 -70

m m dBm dBm

30 degree NTSC ONLY

7. Signal Timing(Resolution) 7-1. PC Mode [Table 7] Timming chart of Receivable ModeMode H_display V_display V frequency H_total H_blanking H_sync H Polarity H_bp H_fp H-freq[kHz] /Clk[MHz] V_total V_blanking V_sync V Polarity V_bp V_fp VGA-60 640 480 60 800 160 96 NEG. 48 16 31.469 25.175 525 45 2 NEG 33 10 VGA-67 640 480 67 864 224 64 NEG. 96 64 35.0 30.24 525 45 3 NEG 39 3

* H [dot] / V [line]

VGA-75 SVGA-56 SVGA-60 SVGA-72 SVGA-75 XGA-70 XGA-75 XGA-60 X 640 480 75 840 200 64 NEG 120 16 37.5 31.5 500 20 3 NEG 16 1 800 600 56 1024 224 72 POS 128 24 35.156 36.0 625 25 2 POS 22 1 800 600 60 1056 256 128 POS 88 40 37.879 40.0 628 28 4 POS 23 1 800 600 72 1040 240 120 POS 64 56 48.077 50.0 666 66 6 POS 23 37 800 600 75 1056 256 80 POS 160 16 46.875 49.5 625 25 3 POS 21 1

1024 768 70 1328 304 136 NEG 144 24 56.476 75.0 806 38 6 NEG 29 3

1024 768 75 1312 288 96 POS 176 16 60.023 78.75 800 32 3 POS 28 1

1024 768 60 1344 304 136 NEG 136 160 48.3 65 806 38 6 NEG 29 3

- 10 -

TIMING CHARTVIDEOA

E D

SYNCC

B

> ModeH/V SortSync Polarity

Dot Clock

Frequency

Total Period Video Active Time (E) (A)

Front Porch (B)

Sync Duration (D)

Back Porch (F)

Resolution

1 2 3 4 5 6 7

H V H V H V H V H V H V H V

+ + + + + +

25.175 28.324 25.175 31.5 40.0 49.5 65.0

31.468 70.090 31.469 70.082 31.469 59.94 37.5 75 37.879 60.317 46.875 75.0 48.363 60.004

800 449 900 449 800 525 840 500 1056 628 1056 625 1344 806

640 350 720 400 640 480 640 480 800 600 800 600 1024 768

16 37 18 13 16 10 16 1 40 1 16 1 24 3

96 2 108 2 96 2 64 3 128 4 80 3 136 6

48 60 54 34 48 33 120 16 88 23 160 21 160 21

640x350 720x400 640x480 800x600 800x600 800x600 1024x768

- 11 -

ADJUSTMENT INSTRUCTION1. Application ObjectThis instruction is for the application to the LCD TV.

2. Adjustment2.1 Adjustment overviewThe unit is set to automatically adjust using the factory automation equipment. However when errors occur, it should be adjusted manually.

2.2 Auto Gain/Offset adjustment2.2.1 RF Mode adjustment 2.2.1.1 Adjustment preparation Conduct Heat Run at the RF fog signals for more than 30 minutes. 2.2.1.2 Auto Gain/Offset adjustment Press IN-START Key to convert to the adjustment mode using the adjustment (SVC) remote controller, and press VOL+ Key at the Auto Gain menu. (In case of RM-15LA70, press IN-START Key twice) Once the adjustment is completed, press the Enter Key to save and finish the adjustment. 2.2.2 Component Mode adjustment 2.2.2.1 Adjustment preparation Conduct Heat Run at the RF fog signals for more than 30 minutes. Connect the Pattern Generator to the Component Jack (Y, Pb, Pr) of LCD TV. 2.2.2.2 Auto Gain/Offset adjustment Convert the input mode to the component input. Using the Pattern Generator (801GF, VG819) adjust WXGA (1280 X 768) for resolution and Color Bar signals for patterns. Or adjust Color Bar signals in accordance with VG819. Press the IN-START Key to convert into the adjustment mode using the adjustment (SVC) remote controller, and press VOL+ Key at the Auto Gain menu. Once the adjustment is completed, press the Enter Key to save and finish the adjustment

2.2.3 PC Mode adjustment 2.2.3.1 Adjustment preparation Conduct Heat Run at the RF fog signals for more than 30 minutes. Connect the Pattern Generator to 15 Pin D-Sub Jack of LCD TV. 2.2.3.2 Auto Gain/Offset adjustment Convert the input mode to PC input. Using the Pattern Generator (801GF, VG819) adjust WXGA (1280 X 768) for resolution and 16 Step Gray signals for the pattern. Or adjust the 16 Step (11 Step) Gray signals in accordance with VG819. Convert the input mode to PC input and convert to the adjustment mode using the adjustment (SVC) remote controller and pressing the IN-START Key, and then press VOL+ Key at the AutoGain menu. Once the adjustment is completed, press the Enter Key to save and finish the adjustment.

2.3 EDID (The Extended Display Identification Data) settingConnect the 15 Pin D-Sub Cable to D-Sub Jack. Set the input mode of Set to PC. Connect the DDC automation equipment to write DDC data. 2.3.1 EDID DATA00 10 20 30 40 50 60 70 00 00 03 1D 01 36 3F 4D 00 01 02 03 04 05 06 07 08 09 FF FF FF FF FF FF 00 1E 6D 0E 01 00 28 1E 17 78 EA B1 50 54 AB 8C 00 31 4F 45 4F 01 01 01 01 01 64 19 00 40 00 30 E4 10 00 00 18 00 00 08 00 0A 20 20 20 20 20 20 31 35 4C 41 36 36 0A 20 20 20 20 20 20 20 20 20 20 20 0A 39 45 61 41 00 00 20 20 0B 75 A1 4F 00 FD 00 20 20 0C 01 58 01 26 00 00 00 20 0D 01 4F 01 30 38 FC 00 20 0E 01 95 01 18 4B 00 00 00 0F 01 26 01 88 1E 52 FC 04

- 12 -

*Option(PAL)NO1 2 3 4 5 6 7 8

ITEMSide AV SCART PC SideComp 16:9 200PR Text ACMS

CONDITION Option 11 1 1 1 1 0 1 1

REMARK0: Side AV Off 1: Side AV On 0: SCART Off 1: SCART On 0: PC Off 1: PC On 0: SideComp Off 1: SideComp On 0: Wide Off 1: Wide On 0: 100 Program 1: 200 Program 0: Text Off 1: Text On 0: ACMS On 1: ACMS Off

NO1

ITEMLanguage

CONDITION Option 31

REMARK0: Eng Only 1: EU5 2: 12 nations(Europe) 3: Eng + Chines 4: Eng + Arab + Urdu 5: Eng + FARSI

2

Txt Lang

0

0: WEST EU 1: EAST EU 1 2: TURKY EU 3: EAST EU 2 4: CYRILLIC 1 5: CYRILLIC 2 6: CYRILLIC 3 7: TURKY GRE 1 8: TURKY GRE 2 9: TURKY GRE 3 10: ARAB FRAN 11: ARAB ENG 12: ARAB HEB 1 13: ARAB HEB 2 14: FARSI ENG 15: FARSI FRA 16: FARI ALL

Option 21 2 3 4 5 6 HiDev Hotel Top I II SAVE Turbo Vol Ch/Aus 0 0 1 1 0 0 0: HiDev Off 1: HiDev On 0: Hotel Off 1: Hotel On 0: Top Off 1: Top On 0: Ch. Sound Non Memory 1: Ch. Sound Memory 0: except below area(Off) 1: Middle-east Area Vol On 0: except below area(Off) 1: China, Australia On 3 4 Inch opt DDCi 0 Analog

reserved Analog: Analog Digital: Digital

- 13 -

SVC REMOCON1 2 3 4 5 6 7 8 9 10 11To turn the TV on or off To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function. MUTE To check TV screen image easily. P-CHECK To check TV screen sound easily S-CHECK To select size of the main screen (Normal, Spectacle, Wide or Zoom) ARC Switch to closed caption broadcasting CAPTION To toggle on/off the teletext mode TXT To select an external input for the TV screen TV/AV To start turbo sound TURBO SOUND TURBO PICTURE To start turbo picture To enter adjustment mode when manufacturing the TV sets. To adjust the screen voltage (automatic): In-start mute Adjust AV(Enter into W/B adjustment mode) IN-START W/B adjustment (automatic): After adjusting the screen W/B adjustment Exit two times (Adjustment completed) To enter into the adjustment mode. To adjust horizontal line and sub-brightness. ADJ To select the multiple sound mode (Mono, Stereo or Foreign language) MPX To release the adjustment mode EXIT To easily adjust the screen according to surrounding brightness APC(PSM) To easily adjust sound according to the program type ASC(SSM) To check component input MULTIMIDIA To check the front AV FRONT-AV To move channel up/down or to select a function displayed on the screen. CH To adjust the volume or accurately control a specific function. VOL To set a specific function or complete setting. ENTER To move the channel down in the PIP screen. PIP CH-(OP1) To use as a red key in the teletext mode To move the channel in the PIP screen PIP CH+(OP2) To use as a green key in the teletext mode To switch between the main and sub screens PIP SWAP(OP3) To use as a yellow key in the teletext mode To select the input status in the PIP screen PIP INPUT(OP4) To use as a blue key in the teletext mode To set a function that will automatically adjust screen status to match EYE the surrounding brightness so natural color can be displayed. To select the functions such as video, voice, function or channel. MENU To set the delivery condition status after manufacturing the TV set. IN-STOP To halt the main screen in the normal mode, or the sub screen at the PIP screen. STILL Used as a hold key in the teletext mode (Page updating is stopped.) Displays the teletext time in the normal mode TIME Enables to select the sub code in the teletext mode Used as the size key in the PIP screen in the normal mode SIZE Used as the size key in the teletext mode Used as the index key in the teletext mode (Top index will be MULTI PIP displayed if it is the top text.) To select the position of the PIP screen in the normal mode Used as the update key in the teletext mode (Text will be POSITION displayed if the current page is updated.) Used as Mode in the teletext mode MODE To select the simultaneous screen PIP To adjust screen tilt TILT To manually select the channel. 0~9

POWER

Shortcut keys Shortcut keys Shortcut keys

12

Use the AV key to enter the screen W/B adjustment mode.

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38

Shortcut keys Shortcut keys

Shortcut keys

- 14 -

TROUBLESHOOTING

No power (LED indicator off)

:[A]Process

Check 15V or 5V of Lips

Fail

Check short of main B/D or Change Lips

Pass Check Output of Q1100 Change Q1100 Fail

Pass

Check Output of IC1107, IC104

Change IC1107, IC1104 Fail

Pass

Check LED Assy Fail

Change LED Assy

Pass

Check P1100, P210 Connector

- 15 -

No Raster

:[B]Process

Check LED Status on display unit

Repeat A PROCESS Fail

Check L900,L901 L902,L903

Fail

Change L900,L901, L902,L903

Pass

Check the input/ Output of IC901

Change IC901 Fail

Pass Change inverter connector or inverter

Check inverter Connector or inverter

Fail

Pass

Check panel link Cable or module

Fail

Change panel link cable or module

Pass Check input source cable and jack Change module

Fail

- 16 -

No Raster on Component signal

Repeat [A] Process

Pass

Check the signal of L1200, L1202, L1203

Fail

Check JA1200 or RCA CABLE

Pass

Check the input/ output of IC1

Fail

Re-soldering or Change the defect part, Check X11

Check the input/output of IC800, IC851

Fail

Re-soldering or Change the defect part

Pass

Check the input/ output of IC901

Fail

Re-soldering or Change the defect part, Check X900

Pass

Check input source cable and jack

- 17 -

No Raster on AV Signal (Video, S-Video)

No Raster on TV(RF) signal

Repeat [A] Process

Fail

Check the output of TU1000

Fail

Check 5V, 33V of TU1000 Re-soldering or Change the defect part

Pass

Check the signal of L1209, L1210, L1212

Fail

Change L1209, L1210, L1212

Pass

Check the input/output of IC1

Fail

Re-soldering or Change the defect part Chek X11

Pass

Check the input/output of IC800, IC851

Fail

Re-soldering or Change the defect part

Pass

Check the input/output of IC901

Fail

Re-soldering or Change the defect part Check X900

Pass

Check input source cable and jack

- 18 -

No Sound

Check the input source

Fail

Change source input

Pass

Check the input/output of IC1 Pass

Fail

Re-soldering or Change the defect part Check X11

Check the input/output of IC100,IC101

Fail

Re-soldering or Change the defect part

Pass

Check the speaker Fail Pass

Change speaker

Check the speaker wire

- 19 -

ML-041B Block DiagramPOWERIC100 IC101 Audio Amp L, R AT49F IC905 GM2221 IC901 TC90A65F IC500 SM5301BS IC800

TTL 1 OUT TTL 2 OUT LVDS 1 OUT

ANALOG SIGNAL DIGITAL SIGNAL SOUND INPUT IF +,- INPUT SOUND OUTPUTPC RGB

VCTI IC1 AT24C16 IC4

Z1000

LA7222 IC2 S A W

SIDE_L,R

BLOCK DIAGRAM

IF+,-

SIDE V

SCART R,G,B SCART V,L,R COMPONENT L,RD-SUB 14066 IC202

Tuner TU1000

PC L,RAUDIO PC

AC IN

Y Pr

Pb

H/P

S-VHS

V

SIDE_AVM52758FP IC851

RGB OUT

- 20 -

BLOCK DIAGRAM DESCRIPTION1. Video Controller Unit & Display Data Conversion Unit The video controller unit receives the video signals inputted through the tuner, AV port (AV1, AV2, S-Video, component), and converts them into an analog RGB signal through the microcomputer (VCTI) combined with the video decoder that integrates various functions in one chip. Either the analog RGB, component YPbPr or PC RGB signal is selected by the switching IC and inputted to a scaler (GM2221), which is sent to the LCD module after being modified to an LVDS signal through the integrated LVDS IC. Or, it is sent to the LCD module as a TTL output. VCTi is the main microprocessor that handles video signal processing and sound signal processing. It also manages the RF signals received from the tuner. The scaler can control timing to fit into the LCD panel, and can also control the size and position of the input signal. 2. Power Supply Unit The power supply unit provides 15V and 5V DC power to the mainboard. The PWM Step-Up DC/DC Converter circuit is used to generate the 33V used for the tuner. 15V power is directly used by the sound amplifier IC and is also used to generate 5V power through the regulator. 12V power is used for the LCD panel power, and 5V power is converted to 3.3V and 1.8V power through the regulator, which in turn supplies electrical power for ICs such as VCTI and scaler.

- 21 -

WIRING DIAGRAM

Wiring Part List2 3

No. 1 2 3 44

Part No. 6631T25019Y 6631T11012R 6631T20028G 6631T20029X 5 6 7 8 9 6631T25021A 6620K00007C or 6620K00007A 6631T11017N 6631T25019L 6631V00040A

9

1

IR_LED

- 22 7 8

5

6

LOCAL KEY

SPEAKER

SPEAKER

EXPLODED VIEW170 030 120

110 140 100 090

150 130 080 160

- 23 020 190 010 050 060 070

050 180 210

200

040 220

230

180

EXPLODED VIEW PARTS LISTNo. PART NO. DESCRIPTION

010

3091TKB050D 3091TKB050E

CABINET ASSEMBLY, RM-15LA67 BRAND 3090V00444 CANADA CABINET ASSEMBLY, RM-15LA67 BRAND 3090V00444 CANADA SKD LCD(LIQUID CRYSTAL DISPLAY), LC150X02-A4K2 LG PHILPS TFT COLOR LEAD FREE LCD(LIQUID CRYSTAL DISPLAY), LC150X02-A4 LG PHILPS TFT COLOR COST COMPENSATION BACK COVER ASSEMBLY, RM-15LA67 3808V00368 CANADA BACK COVER ASSEMBLY, RM-15LA67 3808V00368 CANADA SKD TILT SWIVEL ASSEMBLY, KZ-17LZ23 . . SPEAKER,FULLRANGE, F1527C-6428-4 K-TONE FULL-RANGE(GENERAL) 4 OHM 7/12W 85DB OTHERS 40*70MM TRACK TYPE PWB(PCB) ASSEMBLY,SUB, RM-15LA66 SUB TOTAL BRAND CONTROL BOARD PWB(PCB) ASSEMBLY,SUB, RM/RT/RZ-15/20LA66 CONTROL BOARD CONTROL TOTAL BRAND (MAIN ML-041B) LF PWB(PCB) ASSEMBLY,SUB, RM-15LA66 ML-041B SUB TOTAL BRAND IR B/D PWB(PCB) ASSEMBLY,SUB, RM/RT/RZ-15LA66 IR BOARD LED & P/SW TOTAL BRAND (MAIN ML-041B) LF METAL ASSEMBLY, FRAME MAIN 15LA66/70 (LPL MODULE ONLY) METAL ASSEMBLY, FRAME MAIN C/SKD 15LA66/70 LPL MODULE ONLY BRACKET, AV RZ-20LA62 ML024A HIPS 60HR . MAIN TOTAL ASSEMBLY, RM-15LA70(LPL) BRAND ML-041B PWB(PCB) ASSEMBLY,POWER, AUTOBAHN 15(LPL,CMO,HYDIS) & L173SAB(MFM) LPL POWER TOTAL SPI LIPS. PWB(PCB) ASSEMBLY,POWER, RZ-15LA70 POWER TOTAL POWERNET LIPS FOR CMO/LPL/HD METAL, SHIELD 15LA66 METAL, SHIELD 15LA66 C/SKD PWB(PCB) ASSEMBLY,SUB, RM-20LA70 ML041B SUB TOTAL BRAND JACK(DVD) BOARD ASSY PWB(PCB) ASSEMBLY,SUB, RM/RT-15,17,20 DVD JACK BOARD VIDEO TOTAL BRAND ML-041B LF COVER ASSEMBLY, RT-15LA66 REAR A/V PHONE ML041B BRACKET, REAR AV RZ-15LA66 ML024E HIPS 407AF 70B SPRAY BUTTON, CONTROL RU-15LA61 ABS, HF-380 8KEY . COVER, REAR 15LA60 HIPS 60HR . METAL, STAND NON HINGE ASSY_15LA60 BRACKET, STAND RU-15LA61 ML012C HIPS 60HR FRONT BRACKET, STAND RU-15LA61 ML012C HIPS 60HR REAR BRACKET, DECO RU-15LA61 ML012C ABS, HF-380 . BRACKET, STAND RU-15LA61 ML012C ABS, HF-380 BASE METAL, STAND NON BASE, 15LA60

020

6304FLP212A 6304FLP133B

030

3809TKB029K 3809TKB029L

040 050 060

3043TKK174B 6400GKTX01C 6871TST633A 6871TST977A

070

6871TST635A 6871TST969A

080

4951TKS168A 4951TKS168B

090 100 110

4810V00950B 3313TN1008A 6871TPT281E or 6871TPT281A

120

4950TKS300B 4950TKS300A

130

6871TST561A 6871TST964A

140 150 160 170 180 190 200 210 220 230

3551TKK537D 4810V00925G 5020V00777C 3550V00298B 4950V00157A 4810V00777D 4810V00778D 4810V00776C 4810V00779C 4950V00135A

- 24 -

REPLACEMENT PARTS LISTFor Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows; CC, CX, CK, CN, CH : Ceramic CQ : Polyestor CE : Electrolytic CF : Fixed Film RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RH : CHIP, Metal Glazed(Chip) RR : Drawing

*S *AL LOC. NO.

PART NO.

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION

*S *AL LOC. NO. C928 C929 C930 C934 C935 C936 C937 C938 C939 C940 C943 C944 C945 C946 C947 C948 C949 C950 C956 C964 C965 C967 C968 C97 C970 C13 C14 C2 C20 C21 C46 C50 C59 C7 C8 C9 C907 C923 C924 C129 C130 C1003 C1007 C1010 C107 C109 C110 C1108 C1112 C1113 C1114 C113 C900 C902

PART NO. 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH6102K406 0CH6102K406 0CH6102K406 0CH6102K406 0CH6102K406 0CH6102K406 0CH6102K406 0CH6102K406 0CH6221K416 0CH6221K416 0CH6221K416 0CH6331K416 0CH6080K116 0CH6080K116 181-007F 181-007F 0CH3103K516 0CH3103K516 0CK273DK51A 0CK225DFK4A 0CH3103K516 0CH3103K516 0CK106EF56A 0CK225DFK4A 0CK225DFK4A 0CK225DFK4A 0CK225DFK4A 0CH3103K516 0CH3103K516

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 220PF 50V J NP0 2012 R/TP 220PF 50V J NP0 2012 R/TP 220PF 50V J NP0 2012 R/TP 330PF 50V J NP0 2012 R/TP 8PF 50V D NP0 2012 R/TP 8PF 50V D NP0 2012 R/TP "MPE ECQ-V1H224JL3(TR), 50V 0" "MPE ECQ-V1H224JL3(TR), 50V 0" 10000PF 50V 10% B(Y5P) 2012 10000PF 50V 10% B(Y5P) 2012 27000PF 2012 50V 10% B(Y5P) "2.2UF 2012 16V 20%,-20% F(Y5" 10000PF 50V 10% B(Y5P) 2012 10000PF 50V 10% B(Y5P) 2012 10UF 3216 16V 10% X7R R/TP "2.2UF 2012 16V 20%,-20% F(Y5" "2.2UF 2012 16V 20%,-20% F(Y5" "2.2UF 2012 16V 20%,-20% F(Y5" "2.2UF 2012 16V 20%,-20% F(Y5" 10000PF 50V 10% B(Y5P) 2012 10000PF 50V 10% B(Y5P) 2012

MAIN BOARD CAPACITORC1008 C1101 C1104 C1107 C1140 C1152 C123 C124 C131 C132 C133 C134 C1150 C1151 C127 C128 C135 C136 C15 C16 C19 C203 C4 C41 C44 C49 C6 C803 C804 C808 C810 C812 C851 C854 C855 C858 C861 C863 C865 C866 C867 C869 C871 C874 C875 C877 C909 C910 C917 C920 C925 C926 C927 0CE227CF638 0CE227BH638 0CE227BH638 0CE477BH618 0CE227BH638 0CE107BK638 0CE477BH618 0CE477BH618 0CE477BH618 0CE477BH618 0CE477BH618 0CE477BH618 0CH3105F946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3105F946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3105F946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 0CH3104K946 "220UF SHL,SD 16V M FM5 TP 5" 220U KME 25V M FM5 TP5 220U KME 25V M FM5 TP5 470UF KME TYPE 25V M FL TP 5 220U KME 25V M FM5 TP5 100UF KME 50V M FM5 TP5 470UF KME TYPE 25V M FL TP 5 470UF KME TYPE 25V M FL TP 5 470UF KME TYPE 25V M FL TP 5 470UF KME TYPE 25V M FL TP 5 470UF KME TYPE 25V M FL TP 5 470UF KME TYPE 25V M FL TP 5 1UF 16V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 1UF 16V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 1UF 16V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP 100000PF 50V Z F 2012 R/TP

- 25 -

*S *AL LOC. NO. C1001 C1002 C1004 C1005 C11 C114 C115 C116 C117 C118 C12 C125 C126 C200 C22 C23 C24 C25 C26 C27 C28 C29 C3 C30 C31 C32 C33 C34 C35 C37 C40 C42 C45 C52 C67 C75 C800 C801 C802 C807 C811 C816 C82 C901 C903 C904 C905 C906 C911 C912 C913 C914 C915 C916 C918 C919 C921 C922 C961 C1015 C1016 C121

PART NO. 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK474CH94A 0CK225DFK4A 0CK104CK56A 0CK562CK51A 0CK562CK51A 0CK104CK56A 0CK104CK56A 0CK105EK56A 0CK105EK56A 0CK104CK56A 0CK822CK56A 0CK104CK56A 0CK822CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK334CF94A 0CK104CK56A 0CK104CK56A 0CK334CF94A 0CK104CK56A 0CK334CF94A 0CK334CF94A 0CK104CK56A 0CK334CF94A 0CK334CF94A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK105CF94A 0CK105CF94A 0CK105CF94A 0CK104CK56A 0CK105CF94A 0CK104CK56A 0CK474CH94A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CH5390K416 0CH5390K416 0CC100CK41A

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y "0.47UF 1608 25V 80%,-20% R/T" "2.2UF 2012 16V 20%,-20% F(Y5" 0.1UF 1608 50V 10% R/TP X7R 5600PF 1608 50V 10% R/TP B(Y 5600PF 1608 50V 10% R/TP B(Y 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 1UF 3216 50V 10% X7R R/TP 1UF 3216 50V 10% X7R R/TP 0.1UF 1608 50V 10% R/TP X7R 8200PF 1608 50V 10% X7R R/TP 0.1UF 1608 50V 10% R/TP X7R 8200PF 1608 50V 10% X7R R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 1608 50V 10% R/TP X7R "0.33UF 1608 16V 80%,-20% F(Y" "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 1608 50V 10% R/TP X7R "0.33UF 1608 16V 80%,-20% F(Y" "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R "1UF 1608 16V 80%,-20% R/TP F" "1UF 1608 16V 80%,-20% R/TP F" "1UF 1608 16V 80%,-20% R/TP F" 0.1UF 1608 50V 10% R/TP X7R "1UF 1608 16V 80%,-20% R/TP F" 0.1UF 1608 50V 10% R/TP X7R "0.47UF 1608 25V 80%,-20% R/T" 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 39PF 50V 5% NP0 2012 R/TP 39PF 50V 5% NP0 2012 R/TP 10PF 1608 50V 5% R/TP NP0

*S *AL LOC. NO. C122 C43 C47 C48 C53 C56 C57 C58 C74 C83 C85 C86 C88 C89 C98 C1106 C108 C1100 C1102 C1103 C1105 C1109 C111 C1118 C112 C1124 C1130 C1132 C1134 C1135 C1137 C1149 C119 C120 C17 C5 C55 C60 C61 C62 C852 C856 C859 C864 C868 C87 C873 C876 C888 C96 C99

PART NO. 0CC100CK41A 0CC102CK41A 0CC220CK41A 0CC220CK41A 0CC102CK41A 0CC221CK41A 0CC221CK41A 0CC221CK41A 0CC102CK41A 0CC102CK41A 0CC102CK41A 0CC102CK41A 0CC390CK41A 0CC390CK41A 0CC102CK41A 0CE477BD618 0CE476VH6DC 0CE107WF6DC 0CE227WF6DC 0CE107WF6DC 0CH8476F691 0CE107WF6DC 0CE475WJ6DC 0CE107WF6DC 0CE475WJ6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE227WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CH8106F691 0CH8106F691 0CE475WJ6DC 0CE475WJ6DC 0CE475VK6DC 0CE475VK6DC 0CE475VK6DC 0CE475VK6DC 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CE107WF6DC 0CH8476F691 0CH8106F691 0CE107WF6DC 0CE107WF6DC 0CH8106F691

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION 10PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 22PF 1608 50V 5% R/TP NP0 22PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 220PF 1608 50V 5% R/TP NP0 220PF 1608 50V 5% R/TP NP0 220PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 39PF 1608 50V 5% R/TP NP0 39PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 470UF KME TYPE 10V 20% FL TP 47UF MV 25V 20% R/TP(SMD) SM 100UF MVK 16V 20% R/TP(SMD) 220UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 47UF 16V 20% 105STD (CYL) R/ 100UF MVK 16V 20% R/TP(SMD) 4.7UF MVK 35V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 4.7UF MVK 35V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 220UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 4.7UF MVK 35V 20% R/TP(SMD) 4.7UF MVK 35V 20% R/TP(SMD) 4.7UF MV 50V 20% R/TP(SMD) S 4.7UF MV 50V 20% R/TP(SMD) S 4.7UF MV 50V 20% R/TP(SMD) S 4.7UF MV 50V 20% R/TP(SMD) S 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 100UF MVK 16V 20% R/TP(SMD) 47UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 100UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 10UF 16V 20% 105STD (CYL) R/

DIODEsD100 D101 D1150 D102 D103 D107 ZD104 ZD105 0DRFC00288A 0DRFC00288A 0DRGS00199A 0DS181009AA 0DS181009AA 0DS226009AA 0DZ620009HB 0DZ620009HB SS14 FAIR CHILD R/TP SMA 20SS14 FAIR CHILD R/TP SMA 20UF4001 GENERAL SEMICONDUCTOR KDS181 TP KEC SOT-23 80V 3 KDS181 TP KEC SOT-23 80V 3 KDS226 TP KEC SOT-23 80V 30 UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20

- 26 -

*S *AL LOC. NO. ZD200 ZD209 ZD201 ZD202 ZD203 ZD204 ZD205 ZD206 ZD211 D1151

PART NO. 0DZ620009HB 0DZ620009HB 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ510009EE 0DZ330009DF

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20 UDZ S 5.1B TP ROHM-K SOD323 UDZ S 5.1B TP ROHM-K SOD323 UDZ S 5.1B TP ROHM-K SOD323 UDZ S 5.1B TP ROHM-K SOD323 UDZ S 5.1B TP ROHM-K SOD323 UDZ S 5.1B TP ROHM-K SOD323 UDZ S 5.1B TP ROHM-K SOD323 MTZJ33B TP ROHM-K DO34 0.5W

*S *AL LOC. NO. L1102 L205 L800 L906 L907 L10 L1001 L1002 L15 L2 L8

PART NO. 6210TCE001G 6210TCE001A 6210TCE001G 6210TCE001G 6210TCE001G 0LC1032101A 0LC1020101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION HH-1M3216-501 CERATEC 3216MM HB-1S2012-080JT CERATEC 2012 HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM 10UH 10% 3216 R/TC FI-C32161UH 10% 2012 R/TC FI-B2012-1 10UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C3216-

ICIC905 IC3 IC2 IC200 IC4 IC903 IC100 IC101 IC851 IC1 IC800 IC901 IC1101 IC1103 IC1108 IC1110 IC1110 IC1111 IC1111 IC1113 IC1113 IC1105 IC1106 IC1114 IC1115 IC202 0IZZTSA004A 0IKE702700D 0ISA722200A 0IMMRSG036A 0IMCRAL006A 0IMCRAL006A 0IMCRMZ002A 0IMCRMZ002A 0IMCRMI006A 0IPRPMN003C 0IPRPNP001A 0IPRPGN015C 0IPMGFA061A 0IPMGSG018D 0IMCRKE010A 0IPMG00003A 0ISS780800J 0IPMG00004A 0IMCRFA015A 0IPMG00003A 0ISS780800J 0IPMGFA061A 0IPMGSG018D 0IPMGFA061A 0IPMGFA061A 0IMO140662A ML-041B XGA NT ATMEL 32P PLC "KIA7027AF 3, SOT-89 TP RESET" LA7222 (1280 AUDIO) - - - "M24C02-WMN6T(P),LF SGS-THOMS" AT24C16AN-10SI-2.7 ATMEL 8P AT24C16AN-10SI-2.7 ATMEL 8P MP7720 MONOLITHIC POWER SYST MP7720 MONOLITHIC POWER SYST "M52758FP MITSUBISHI 36PIN, R" VCT49XYF C7(NTSC+PAL) MICRON "SM5301BS(ATSC DTV) NPC 28P,H" "GM2221-BC-LF,PB FREE GENESIS" "FAN1587AD33X FAIRCHILD 3P,DP" "LD1086DT18TR SGS-THOMSON 3P," KIA7812AF KEC 2P DPACK R/TP "KIA78M08F KEC 3P,DPAK R/TP 8" "KA78M08R 3P,D-PAK TP VOL. RE" "KIA7805AF KEC 3P,DPAK R/TP 5" KA7805R FAIRCHILD 2P D-PAK R "KIA78M08F KEC 3P,DPAK R/TP 8" "KA78M08R 3P,D-PAK TP VOL. RE" "FAN1587AD33X FAIRCHILD 3P,DP" "LD1086DT18TR SGS-THOMSON 3P," "FAN1587AD33X FAIRCHILD 3P,DP" "FAN1587AD33X FAIRCHILD 3P,DP" "MC14066BDR2 14P,SOIC TP BILA"

FET & TRANSISTORIC1107 Q1150 Q1 Q603 Q900 Q100 Q1000 Q101 Q1100 Q1151 Q12 Q13 Q14 Q15 IC902 IC1104 0TF492509AA 0TR322809AB 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR388109AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR150400BA 0TR150400BA 0TR150400BA 0TR387500AA 0TFVI80005A 0TFVI80005A SI4925DY TP TEMIC 30V 6.1A KTC3228-Y(KTC2383) TP KEC TO CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC KTC3881 CHIP TP KEC - CHIP 2SA1504S(ASY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SA1504S(ASY) BK KEC CHIP 2SA1504S(ASY) BK KEC CHIP 2SA1504S(ASY) BK KEC CHIP 2SC3875S(ALY) BK KEC VISHAY SI4963DY R/TP SO-8 -2 VISHAY SI4963DY R/TP SO-8 -2

RESISTORsL1104 R1004 R1010 R1012 R106 R107 R1108 R1109 R1151 R1153 R126 R132 R133 R134 R135 R14 R140 R141 R142 R143 R144 R145 R146 R147 R211 R212 R213 R214 R215 0RH2202D622 0RH3000D622 0RH7501D622 0RH7502D622 0RH1500D622 0RH1003D622 0RH1003D622 0RH1003D622 0RH4700D622 0RH1000D622 0RH4701D622 0RH1003D622 0RH1003D622 0RH1003D622 0RH1003D622 0RH4701D622 0RH0392D622 0RH0392D622 0RH0392D622 0RH0392D622 0RH0392D622 0RH0392D622 0RH0392D622 0RH0392D622 0RH0752D622 0RH0752D622 0RH0752D622 0RH4703D622 0RH3901D622 22K 1/10W 5 D.R/TP 300 1/10W 5 D.R/TP 7.5K 1/10W 5 D.R/TP 75K 1/10W 5 D.R/TP 150 1/10W 5 D.R/TP 100K 1/10W 5 D.R/TP 100K 1/10W 5 D.R/TP 100K 1/10W 5 D.R/TP 470 1/10W 5 D.R/TP 100 1/10W 5 D.R/TP 4.7K 1/10W 5 D.R/TP 100K 1/10W 5 D.R/TP 100K 1/10W 5 D.R/TP 100K 1/10W 5 D.R/TP 100K 1/10W 5 D.R/TP 4.7K 1/10W 5 D.R/TP 39 1/10W 5 D.R/TP 39 1/10W 5 D.R/TP 39 1/10W 5 D.R/TP 39 1/10W 5 D.R/TP 39 1/10W 5 D.R/TP 39 1/10W 5 D.R/TP 39 1/10W 5 D.R/TP 39 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 470K 1/10W 5 D.R/TP 3.9K 1/10W 5 D.R/TP

COIL & CORE & INDUCTORL104 L105 L1150 L1100 L1101 L1103 L1105 L1106 L1107 L200 L201 L202 L203 L204 L853 L900 L901 L902 L903 L905 6140TBZ045A 6140TBZ045A 150-985B 6210TCE001G 6210TCE001G 6210TCE001A 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001A "38.5UH(DIP), 6A, P7.5, DR8.3" "38.5UH(DIP), 6A, P7.5, DR8.3" DR8*11 2.4MH 0.16MM 270.5T HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HB-1S2012-080JT CERATEC 2012 HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HB-1S2012-080JT CERATEC 2012

- 27 -

*S *AL LOC. NO. R216 R217 R57 R59 R6 R74 R818 R9 R908 R910 R915 R920 R934 R989 R999 R1149 R136 R137 C931 C932 R1002 R1011 R1106 R1152 R1155 R12 R128 R129 R13 R148 R149 R202 R208 R209 R210 R36 R817 R822 R903 R918 R961 R964 R985 R995 R10 R1001 R1003 R1005 R1014 R11 R1105 R1107 R1150 R124 R125 R127 R130 R131 R138 R139 R15 R16

PART NO. 0RH3901D622 0RH4703D622 0RH1000D622 0RH1201D622 0RH4702D622 0RH1000D622 0RH8200D622 0RH4701D622 0RH0822D622 0RH0822D622 0RH3600D622 0RH2200D622 0RH1000D622 0RH8200D622 0RH1000D622 0RH2200D622 0RH8202D622 0RH8202D622 0RH0000D622 0RH0000D622 0RH1501D622 0RH0000D622 0RH1002D622 0RH1001D622 0RH1002D622 0RH1001D622 0RH1002D622 0RH1002D622 0RH1001D622 0RH0000D622 0RH0000D622 0RH0222D622 0RH0222D622 0RH0222D622 0RH0222D622 0RH0000D622 0RH0000D622 0RH1002D622 0RH0000D622 0RH1001D622 0RH0000D622 0RH1002D622 0RH0000D622 0RH0000D622 0RJ3301D677 0RJ0562D677 0RJ8200D677 0RJ0682D677 0RJ1000D677 0RJ3301D677 0RJ1001D677 0RJ4701D677 0RJ0102D677 0RJ1500D677 0RJ4701D677 0RJ2701D677 0RJ1202D677 0RJ1202D677 0RJ1002D677 0RJ1002D677 0RJ0822D677 0RJ2200D677

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION 3.9K 1/10W 5 D.R/TP 470K 1/10W 5 D.R/TP 100 1/10W 5 D.R/TP 1.2K 1/10W 5 D.R/TP 47K 1/10W 5 D.R/TP 100 1/10W 5 D.R/TP 820 1/10W 5 D.R/TP 4.7K 1/10W 5 D.R/TP 82 1/10W 5 D.R/TP 82 1/10W 5 D.R/TP CHIP 360-J 1/10 W 220 1/10W 5 D.R/TP 100 1/10W 5 D.R/TP 820 1/10W 5 D.R/TP 100 1/10W 5 D.R/TP 220 1/10W 5 D.R/TP 82K 1/10W 5 D.R/TP 82K 1/10W 5 D.R/TP 0 OHM 1 / 10 W 2012 5.00% D 0 OHM 1 / 10 W 2012 5.00% D 1.5K OHM 1 / 10 W 2012 5.00% 0 OHM 1 / 10 W 2012 5.00% D 10K OHM 1 / 10 W 2012 5.00% 1K OHM 1 / 10 W 2012 5.00% D 10K OHM 1 / 10 W 2012 5.00% 1K OHM 1 / 10 W 2012 5.00% D 10K OHM 1 / 10 W 2012 5.00% 10K OHM 1 / 10 W 2012 5.00% 1K OHM 1 / 10 W 2012 5.00% D 0 OHM 1 / 10 W 2012 5.00% D 0 OHM 1 / 10 W 2012 5.00% D 22 OHM 1 / 10 W 2012 5.00% D 22 OHM 1 / 10 W 2012 5.00% D 22 OHM 1 / 10 W 2012 5.00% D 22 OHM 1 / 10 W 2012 5.00% D 0 OHM 1 / 10 W 2012 5.00% D 0 OHM 1 / 10 W 2012 5.00% D 10K OHM 1 / 10 W 2012 5.00% 0 OHM 1 / 10 W 2012 5.00% D 1K OHM 1 / 10 W 2012 5.00% D 0 OHM 1 / 10 W 2012 5.00% D 10K OHM 1 / 10 W 2012 5.00% 0 OHM 1 / 10 W 2012 5.00% D 0 OHM 1 / 10 W 2012 5.00% D 3.3K OHM 1/10 W 5% 1608 R/TP 56 OHM 1/10 W 5% 1608 R/TP 820 OHM 1/10 W 5% 1608 R/TP 68 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 3.3K OHM 1/10 W 5% 1608 R/TP 1K OHM 1/10 W 5% 1608 R/TP 4.7K OHM 1/10 W 5% 1608 R/TP 10 OHM 1/10 W 5% 1608 R/TP 150 OHM 1/10 W 5% 1608 R/TP 4.7K OHM 1/10 W 5% 1608 R/TP 2.7K OHM 1/10 W 5% 1608 R/TP 12K OHM 1/10 W 5% 1608 R/TP 12K OHM 1/10 W 5% 1608 R/TP 10K OHM 1/10 W 5% 1608 R/TP 10K OHM 1/10 W 5% 1608 R/TP 82 OHM 1/10 W 5% 1608 R/TP 220 OHM 1/10 W 5% 1608 R/TP

*S *AL LOC. NO. R17 R18 R19 R20 R203 R205 R206 R207 R21 R218 R219 R22 R220 R221 R224 R225 R226 R227 R229 R23 R230 R24 R240 R25 R28 R29 R34 R41 R45 R46 R50 R51 R52 R53 R54 R55 R56 R58 R60 R62 R64 R66 R68 R69 R70 R72 R73 R75 R76 R77 R78 R80 R835 R838 R901 R902 R904 R907 R909 R911 R912 R913

PART NO. 0RJ0822D677 0RJ2200D677 0RJ0822D677 0RJ2200D677 0RJ1000D677 0RJ0222D677 0RJ1001D677 0RJ1001D677 0RJ0222D677 0RJ1002D677 0RJ1002D677 0RJ1500D677 0RJ7502D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ2701D677 0RJ7502D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ0000D677 0RJ0000D677 0RJ0000D677 0RJ1000D677 0RJ1000D677 0RJ1001D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1500D677 0RJ1000D677 0RJ1500D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ2202D677 0RJ1000D677 0RJ1000D677 0RJ0472D677 0RJ0472D677 0RJ0472D677 0RJ3301D677 0RJ0822D677 0RJ4701D677 0RJ1000D677 0RJ0000D677

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION 82 OHM 1/10 W 5% 1608 R/TP 220 OHM 1/10 W 5% 1608 R/TP 82 OHM 1/10 W 5% 1608 R/TP 220 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 22 OHM 1/10 W 5% 1608 R/TP 1K OHM 1/10 W 5% 1608 R/TP 1K OHM 1/10 W 5% 1608 R/TP 22 OHM 1/10 W 5% 1608 R/TP 10K OHM 1/10 W 5% 1608 R/TP 10K OHM 1/10 W 5% 1608 R/TP 150 OHM 1/10 W 5% 1608 R/TP 75K OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 2.7K OHM 1/10 W 5% 1608 R/TP 75K OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 0 OHM 1/10 W 5% 1608 R/TP 0 OHM 1/10 W 5% 1608 R/TP 0 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 1K OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 150 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 150 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 22K OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 47 OHM 1/10 W 5% 1608 R/TP 47 OHM 1/10 W 5% 1608 R/TP 47 OHM 1/10 W 5% 1608 R/TP 3.3K OHM 1/10 W 5% 1608 R/TP 82 OHM 1/10 W 5% 1608 R/TP 4.7K OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 0 OHM 1/10 W 5% 1608 R/TP

- 28 -

*S *AL LOC. NO. R914 R917 R928 R929 R930 R931 R932 R935 R936 R938 R939 R941 R942 R943 R944 R945 R946 R947 R950 R951 R953 R954 R96 R979 R980 R981 R982 R983 R984 R991 R992

PART NO. 0RJ0000D677 0RJ0000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1002D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ0000D677 0RJ4701D677 0RJ3301D677 0RJ1002D677 0RJ3301D677 0RJ3301D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ1000D677 0RJ3301D677 0RJ3301D677

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION 0 OHM 1/10 W 5% 1608 R/TP 0 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 10K OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 0 OHM 1/10 W 5% 1608 R/TP 4.7K OHM 1/10 W 5% 1608 R/TP 3.3K OHM 1/10 W 5% 1608 R/TP 10K OHM 1/10 W 5% 1608 R/TP 3.3K OHM 1/10 W 5% 1608 R/TP 3.3K OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 100 OHM 1/10 W 5% 1608 R/TP 3.3K OHM 1/10 W 5% 1608 R/TP 3.3K OHM 1/10 W 5% 1608 R/TP

*S *AL LOC. NO. SW2204 SW2205 SW2205 SW2206 SW2206 SW2207 SW2207

PART NO. 140-313B 140-313A 140-313B 140-313A 140-313B 140-313A 140-313B

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION TACT 2LEAD 160G(TA) LG C&D N TACT 2LEAD 100G(TA) LG C&D N TACT 2LEAD 160G(TA) LG C&D N TACT 2LEAD 100G(TA) LG C&D N TACT 2LEAD 160G(TA) LG C&D N TACT 2LEAD 100G(TA) LG C&D N TACT 2LEAD 160G(TA) LG C&D N

JACK BOARDC1215 C1216 C1221 C1223 C1224 L1200 L1202 L1203 L1206 L1207 L1208 L1211 L1212 L1213 L1214 L1215 R1201 R1202 R1217 R1218 R1219 R1220 R1224 R1225 R1230 R1231 R1232 R1233 R1234 R1235 ZD1200 ZD1206 ZD1207 ZD1212 ZD1213 ZD1214 JA1200 JA1201 C1217 C1218 C1219 C1220 L1209 L1210 R1226 R1227 R1228 R1229 ZD1210 ZD1211 0CH3103K516 0CH3103K516 0CH6331K416 0CH6471K416 0CH6471K416 0RH0752D622 0RH0000D622 0RH0000D622 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 0LC0233002A 6210TCE001A 6210TCE001A 6210TCE001A 0RH0000D622 0RH0752D622 0RH0752D622 0RH0752D622 0RH0752D622 0RH0752D622 0RJ1000H680 0RJ1000H680 0RH0752D622 0RH0752D622 0RH5101D622 0RH4703D622 0RH5101D622 0RH4703D622 0DZ620009HB 0DZ620009HB 0DZ620009HB 0DZ620009HB 0DZ620009HB 0DZ620009HB 6612VJH008D 6613V00008F 0CH3104K946 0CH6331K416 0CH6331K416 0CH6331K416 0LC0233002A 0LC0233002A 0RH0472D622 0RH0752D622 0RH0752D622 0RH0752D622 0DZ620009HB 0DZ620009HB 10000PF 50V 10% B(Y5P) 2012 10000PF 50V 10% B(Y5P) 2012 330PF 50V J NP0 2012 R/TP 470F 50V J NP0 2012 R/TP 470F 50V J NP0 2012 R/TP 75 1/10W 5 D.R/TP 0 OHM 1 / 10 W 2012 5.00% D 0 OHM 1 / 10 W 2012 5.00% D HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 3.3UH CERATECH R/TP HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 0 OHM 1 / 10 W 2012 5.00% D 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 100 OHM 1/2 W 5% 5025 R/TP 100 OHM 1/2 W 5% 5025 R/TP 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 5.1K 1/10W 5 D.R/TP 470K 1/10W 5 D.R/TP 5.1K 1/10W 5 D.R/TP 470K 1/10W 5 D.R/TP UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20 PJ6063D PARKELEC DVD IN 3P G PMJ014F PARK ELEC E/P(ST)+S100000PF 50V Z F 2012 R/TP 330PF 50V J NP0 2012 R/TP 330PF 50V J NP0 2012 R/TP 330PF 50V J NP0 2012 R/TP 3.3UH CERATECH R/TP 3.3UH CERATECH R/TP 47 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP 75 1/10W 5 D.R/TP UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20

OTHERsZ1000 JA201 X11 X900 IC905 TU1000 6200QL3002F 6612VCH003B 6202TST003C 6202VDT002B 6620F00017A 6700VS0003D "X6966M EPCOS ST SIP5K, 6200Q" PEJ012C PARK ELEC H=6.5 STER HC-49/SM5H KONY CHIP 20.25MH SX-1 SUNNY SC14.3MHZ +/- 30 CCSD-32T-SM WOOYOUNG 32P PLC TAEW-G052P LGIT MULTI VS RCA

CONTROL BOARDR2200 R2201 R2202 R2203 R2204 R2205 R2206 R2207 R2208 SW2200 SW2200 SW2201 SW2201 SW2202 SW2202 SW2203 SW2203 SW2204 0RN1101F409 0RN8200F409 0RN5600F409 0RN4700F409 0RN3900F409 0RN3300F409 0RN2700F409 0RN3301F409 0RN2000F409 140-313A 140-313B 140-313A 140-313B 140-313A 140-313B 140-313A 140-313B 140-313A 1.10K 1/6W 1% TA52 820 1/6W 1% TA52 560 1/6W 1% TA52 470 1/6W 1 TA52 390 1/6W 1% TA52 330 1/6W 1% TA52 270 1/6W 1% TA52 3.30K 1/6W 1% TA52 200 1/6W 1% TA52 TACT 2LEAD 100G(TA) LG C&D N TACT 2LEAD 160G(TA) LG C&D N TACT 2LEAD 100G(TA) LG C&D N TACT 2LEAD 160G(TA) LG C&D N TACT 2LEAD 100G(TA) LG C&D N TACT 2LEAD 160G(TA) LG C&D N TACT 2LEAD 100G(TA) LG C&D N TACT 2LEAD 160G(TA) LG C&D N TACT 2LEAD 100G(TA) LG C&D N

- 29 -

*S *AL LOC. NO.

PART NO.

DATE: 2005. 01. 28. DESCRIPTION / SPECIFICATION

IR BOARDC2101 L2101 Q2101 Q2102 Q2103 R2101 R2102 R2103 R2104 R2105 R2106 R2111 LED1 PA1101 0CH3104K566 6210TCE001A 0TR387500AA 0TR387500AA 0TR387500AA 0RH1000D622 0RH1000D622 0RH1001D622 0RH1001D622 0RH1001D622 0RH1000D622 0RH4301D622 0DL200000CA 6726TV0001A 0.1UF 50V 10% X7R 2012 R/TP HB-1S2012-080JT CERATEC 2012 CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC 100 1/10W 5 D.R/TP 100 1/10W 5 D.R/TP 1K OHM 1 / 10 W 2012 5.00% D 1K OHM 1 / 10 W 2012 5.00% D 1K OHM 1 / 10 W 2012 5.00% D 100 1/10W 5 D.R/TP 4.3K 1/10W 5 TA SAM5670(DL-2LRG) BK Y-GREEN TSOP4838SO1 VISHAY 38.0KHZ L

- 30 -

Date: 2004. 05. 07 P/No.:3854TN1001A

Date: 2004. 05. 07 P/No.:3854TN1001A

P/NO : 3828TSL108Y

Jan., 2005 Printed in Korea