trvseries - hifihifi.com.sg/journal/triode_product_2013.pdf · trvseries [trv-4se] tubepreamplifier...

11
TRVseries [ TRV-4SE ] tube preamplifier [ TRV-4SE Limited ] tube preamplifier ( Special version ) basic circuit formal: -- NF type Class A amplification phono circuit formal: -- NF type MM cartridge correspondence frequency characteristic: -1 and -3dB ( 10Hz - 100kHz ) signal to noise ratio:96dB output impedance:7kohm Koa -- highly precise -- resistor use input terminal:4 lines ( the one front part and the three rears ) one tape-out recording output terminal: -- three lines tubes:--ECC83 amplification stage, rectification stage: -- 5AR4x2 demention -- 340Wx185Hx315Dmm weight: -- 8kg Tube cover Wooden side plates, AC cable [ TRV-35SE ] EL34 push-pull integrated / power amplifier maximum output: -- 45W+45W ( 8ohms ) output tube: -- EL34 AB class push pull 3 inputs RCA ( the one front part and the two rears ) one preamplifier input, tape-out recording 1 line Fequency response 10Hz- 100 kHz ( -1,-4dB)■ SNlevel 90dB output:impedance 6 / 8ohm Total distortion < 0.1%( 1kHz )■ Input sencitivity 0.7V Tubes EL34 * 4 , 12AU7 ( ECC82 ) * 2, 12AX7 ( ECC83 ) *1 head phone terminal Power sanction min 100watts/ max 220watts KOA highly precise resistor use USA quality speaker terminal use outside size:340Wx185Hx315Dmm waight:15kg Tube cover Wooden side plates, AC cable

Upload: hoangthien

Post on 07-May-2018

229 views

Category:

Documents


1 download

TRANSCRIPT

TRVseries[TRV-4SE] tube preamplifier[TRV-4SE Limited] tube preamplifier (Special version)■ basic circuit formal: -- NF type Class A amplification ■ phono circuit formal: -- NF type MM cartridgecorrespondence ■ frequency characteristic: -1 and -3dB(10Hz - 100kHz)■ signal to noise ratio:96dB ■ output impedance:7kohm ■ Koa -- highly precise -- resistor use■ input terminal:4 lines ( the one front part and the three rears) one tape-out recording■ output terminal: -- three lines ■ tubes:--ECC83 amplification stage, rectification stage: -- 5AR4x2■ demention -- 340Wx185Hx315Dmm ■ weight: -- 8kg■ Tube cover、Wooden side plates, AC cable

[TRV-35SE] EL34 push-pull integrated / power amplifier■ maximum output: -- 45W+45W (8ohms) ■ output tube: -- EL34 AB class push pull■ 3 inputs RCA ( the one front part and the two rears) one preamplifier input, tape-out recording 1 line■ Fequency response 10Hz- 100 kHz (-1,-4dB)■ SNlevel 90dB■ output:impedance 6 / 8ohm ■ Total distortion < 0.1%(1kHz)■ Input sencitivity 0.7V■ Tubes EL34 * 4 , 12AU7(ECC82) * 2, 12AX7(ECC83) * 1 ■ head phone terminal■ Power sanction min 100watts/ max 220watts ■ KOA highly precise resistor use■ USA quality speaker terminal use ■ outside size:340Wx185Hx315Dmm ■ waight:15kg■ Tube cover、Wooden side plates, AC cable

[TRV-88SE] KT88 push-pull integrated / power amplifier■ maximum output: -- 45W+45W (8ohms) ■ output tube: -- KT88 AB class push pull■ 3 inputs RCA ( the one front part and the two rears) one preamplifier input, tape-out recording 1 line■ Fequency response 10Hz- 100 kHz (-1,-4dB)■ SN level 90dB ■ output:impedance 6 / 8ohm■ Total distortion < 0.1%(1kHz)■ Input sencitivity 0.7V ■ head phone terminal■ Tubes KT8834 * 4 , 12AU7(ECC82) * 2, 12AX7(ECC83) * 1 ■ KOA highly precise resistor use■ Power sanction min 100watts/ max 220watts ■ USA quality speaker terminal use■ outside size:340Wx185Hx315Dmm ■ waight:15kg ■ Tube cover、Wooden side plates, AC cable

[TRV-88SER] KT88 push-pull integrated amplifier NEW MODELThis is the newest Integrated Amplifier designed by Junichi Yamazaki of Triode Corporation-Japan. It is a 45 watts per channel using

KT88 tubes which create a delicate and holographic sound. The ability to convey a deep, detailed and rich character of the instrument

is just phenomenal. Lightning quick in response and the ability to deliver minute details in the recording will easily suck you into the

music. The newly designed EI- Orient Core Output transformer creates thundering quick bass, big soundstage and incredible details

makes this amplifier one of its kind. Remote control included. Please give us a call and be ready to be amazed. Get yourself ready for

a booming year.

■ Remote control: volume, mute ■ Maximum output: 45W+45W ■ Output tube: KT88 ABclass push pull■ MM phono stage , 3 inputs RCA ( the one front part and the two rears) tape-out recording 1 line■ Fequency response 10Hz- 100 kHz (-1,-4dB)■ SN level 90dB ■ output:impedance 6 / 8ohm■ Total distortion < 0.1%(1kHz)■ Input sencitivity 0.4V ■ head phone terminal■ Tubes KT88 * 4 , 12AU7(ECC82) * 2, 12AX7(ECC83)* 1 ■ Power sanction min 100watts/

max 220watts ■ KOA highly precise resistor use ■ USA quality speaker terminal use ■ outsidesize:340Wx185Hx315Dmm ■ waight:15kg ■ Remote control ,Tube cover , Wooden side plates , AC cable

[TRV-A88SE] KT88 single ended integrated amplifier■ maximum output:--12W+12W(8ohms) fixed bias ■ output tube:-- KT88 A class single-ended■ output:impedance 6 / 8ohm ■ KOA highly precise resistor use ■ Hi quality capacitor use■ Frequency response 15Hz- 40 kHz (+1,-1dB)■ Total distortion < 0.1%(1kHz)■ SN level 88dB ■ Input sencitivity 0.7V ■ Tubes KT88 * 2 , 12AX7(ECC83) * 2■ Output inpedance 6 - 8 ohm ■ Input terminals 3 ( LINE 1 / 2 / 3)■ Power sanction 60watts ■ demention:230Wx185Hx400Dmm ■ weight:11.5kg■ Tube cover、Wooden side plates, AC cable

[TRV-A300SE] 300B single ended integrated amplifier■ maximum output: -- 8W+8W (8ohms) self bias ■ output tube: -- 300B A class single -ended■ output impedance 6 / 8ohm ■ KOA highly precise resistor use ■ Hi quality capacitor use■ Frequency response 10Hz- 50 kHz (+1,-1dB)■ Total distortion < 0.3%(1kHz)■ SN level 85dB ■ Input sencitivity 0.6V ■ Tubes 300B * 2 , 6SN7 * 2■ Output inpedance 6 - 8 ohm ■ Input terminals 3 ■ Power sanction 80watts■ demention:230Wx185Hx400Dmm ■ weight:11.5kg■ Tube cover、Wooden side plates, AC cable

[TRV-A300SER]300B single ended integrated amplifier NEW MODEL■ maximum output: -- 8W+8W (8ohms) self bias ■ output tube: -- 300B A class single -ended■ output impedance 6 / 8ohm ■ KOA highly precise resistor use ■ Hi quality capacitor use■ Frequency response 10Hz- 50 kHz (+1,-1dB)■ Total distortion < 0.3%(1kHz)■ SN level 87dB ■ Input sencitivity 0.6V ■ Tubes 300B * 2 , 12AU7 * 2, 12AX7 * 1, 5AR4 * 1■ Input terminals 3 ■ Power sanction 90watts■ demention: 340W x 195H x 315Dmm ■ weight:16kg■ Remote dontrol, Tube cover, Wooden side plates, AC cable

[TRV-M300SE] 300B parallel single ended mono power amplifier■ maximum output: -- 20W+20W (8ohms) fixed bias ■ output tube: -- 300B A class parrale single-ended ■ output:impedance 6 / 8 / 16ohm ■ KOA highly precise resistor use■ Hi qualityl capacitor use ■ Frequency response 10Hz- 60 kHz (+1,-3dB)■ Total distortion < 0.3%(1kHz) ■ SN level 89dB ■ Input sencitivity 0.8V■ Tubes 300B * 2 , 12AX7 * 1 ,12AU7 * 1 ■ Input terminals, ballance 1 ,unballance 1■ Power sanction 120watts ■ demention:176Wx200Hx 440Dmm ■ weight:15kg■ Tube cover, AC cable

[

[TRV-M88SE] KT88 push pull mono power amplifier■ maximum output: -- 50W+50W (8ohms) fixed bias ■ output tube: -- KT88 classAB■ output:impedance 6 / 8 / 16ohm ■ KOA highly precise resistor use■ Hi quality capacitor use ■ Frequency response 20Hz- 50 kHz (+1,-1dB)■ Total distortion < 0.1%(1kHz) ■ SN level 90dB ■ Input sencitivity 0.7V■ Tubes KT88 * 2 , 12AX7 * 1 ,12AU7 * 1 ■ Input terminals, ballance 1 ,unballance 1■ Power sanction 120watts ■ demention:176Wx200Hx 440Dmm ■ weight:15kg■ Tube cover, AC cable

[TRV-CD4SE] 24bit192kHz up sampling CD player■ Total distortion: 0.002% ■ SN level: 100dB ■ Frequency Response: 20-20kHz(± 0.2dB)■ Channel separation: 92dB ■ Dinamic range: 120dB ■ DA conveter:Barbrown PCM1792■ Tubes: 6DJ8(6922)*1 ■ CD drive unit: Sony ■ Dgital output:Rca and Tos■ Power requirements: 20W ■ Dimension: 340*330*100mm(W/D/H)

■ Analogue output terminals, RCA*1, Ballance*1 ■ Digital output terminals: RCA , TOS■ Power sanction 20watts ■ Demention:340Wx100Hx 330Dmm ■ weight:20kg■ Remote control, AC cable

[TRV-EQ3SE] Phono Pre-Ampifier with MC■ NF type MM MC Phono Stage ■ Frequency response:10Hz - 70kHz( -1dB)■ Total distortion: 0.1% ■ Input level MM 2.5mV, MC Low 0.23mV, MC High 0.19mV■ Input Impedance MM 47kohm MC 40ohm ■ S/N ratio in Input MM90dB, MC87dB■ Gain MM 42.5dB, MC Low 58.7, MC High 64.4dB ■ Output Voltage 200mV (1,000 Hz)■ Maximum Input Capability 250mV(1kHz) 11mV(1kHz)■ RIAA Curve Deviation +/-0.25 dB (20 to 20,000Hz) ■ Channel Separation More than 90dB■ Low Cut Filter: 15Hz 18dBoct., ■ Input terminal: 3 lines (MM/ MC1/ MC2)■ Output terminal: 2 lines (RCA/ XLR)■ Capacitors : Mundorf Capacitor■ Resistors: Kiwame Resistors■ Tubes:ECC803 x 4 (JJ electronics/Slovakia) 5AR4 x 1(JJ electronics/Slovakia)■ Power Consumption 15W ■ Dimention W 340mm x D 315mm x H 185mm■ Weight 10.0 kg

Analog disc playing has deeply improved on the present popular digital audio sources, and now along combined isan individual phono amp seeking more of a sound quality.Therefore the functions sought in the previous phono ampis consolidated to the signal source selection and volume adjustment.

[Low noise design]In the rectification circuit of the amplifier, rectification tubes without switching noise in principle and luxuriousrectification circuit with choke transformer are used.

[Simple signal transfer]The amplifier minimizes the functions only needed for this amplifier, and the pureness of signals is secured by notpassing through any unnecessary points.

[Special Features of MC transformer]High stepup efficiency with low loss, reducing a half of transmission loss / Super-perm-alloy gigantic EI corewinded / low-loss big copper wire / High linearity in low range / Energetic sound in all ranges supported bycarefully-selected materials / Good rise characteristics minimize a phase distortion in audible bandwidgh and clarify /the great sound image / Energetic, lively music reproduction / The winding structure, uniquely devided into layers,for wide bandwidth responseand high rise time / Vibration and co-vibration-free body structure by the weighted iron chasisReproduce realistic music with good S/N images

[TR-MC1SE] MC step-up transformer■ Frequency response:10Hz - 70kHz( -1dB) ■ Input Impedance MC 2 - 47ohm■ Gain MC Low 16dB, MC High 22dB ■ Input terminal: 2 lines (MC1/ MC2)■ Dimention W 180mm x D 155mm x H 145mm■ Weight 2.5 kg[Special Features of MC transformer]High stepup efficiency with low loss, reducing a half of transmission loss / Super-perm-alloy gigantic EI corewinded / low-loss big copper wire / High linearity in low range / Energetic sound in all ranges supported bycarefully-selected materials / Good rise characteristics minimize a phase distortion in audible bandwidgh and clarify /the great sound image / Energetic, lively music reproduction / The winding structure, uniquely devided into layers,for wide bandwidth responseand high rise time / Vibration and co-vibration-free body structure by the weighted ironchasis / Reproduce realistic music with good S/N images

[TRV-845SE] 845 single ended integrated amplifier with remote control■ maximum output: -- 20W+20W (8ohms) fixed bias ■ output tube: -- 845 class-A single -ended■ output:impedance 4 / 8 / 16ohm ■ KOA highly precise resistor use■ Alps high quality volume ■ Frequency response 10Hz- 50 kHz (0,-1dB)■ Total distortion < 0.1%(1kHz) ■ SN level 89dB ■ Input sencitivity 0.9V■ Tubes 300B * 2 , 2A3 * 2 ,6SN7 * 2 ■ Input terminals, ,RCA 4, XLR 1, PRE-IN 1■ Remote control : Volume, Input Selector, Muting■ Power sanction 300watts ■ demention:460Wx260Hx 450Dmm ■ weight:38kg■ Remote unit, tube cage, power cable, spare fises

* TRV-845SE is a Pure Class-A Pre-main amplifier fully consists of triode tubes.* By using 2A3 tubes to drive 845, a sharp and delicate sound of 845 is further improved.* A newly developed large EI Orient-core output transformer creates a profound middle

and bass sound.* We arranged a remote control for TR-845SE for the first time.* TRV-845SE is equipped with Pre-In facility to use the unit as a Power Amplifier as well.

TRXseries[TRX-1] tube preamplifier with remote controlTRX-1 is the newest Pre-Amplifier designed by Junichi Yamazaki of Triode Corporation-Japan. It is using 274B rectifier tube that

creates deeper bass with a very delicate and holographic sound. The combination of TRX-P6L, TRX-1 Pre-Amp and TRV-DC4SE

convey a deep, detailed and rich character of the instrument is phenomenal. Lightning quick in response and the ability to deliver

details in the recording will easily suck you into the music. The newly designed humungous EI-Orient Core Output transformer creates

thundering quick bass, big soundstage and incredible details makes this amplifier one of its kind.

■ circuit formal: NF type ClassA amplification ■ 4 band Equalizer frequency:150,400,2K,10KHz +/-6dB■ frequency characteristic: -1 and -3dB(10Hz - 100kHz) ■ signal to noise ratio:96dB■ output impedance: 6kohm ■ Koa -- highly precise -- resistor use ■ input terminal: 5 lines■ output terminal: -- three lines ■ tubes: ECC83 amplification stage, rectification stage: 274B(5U4G)x1■ demention -- 340Wx185Hx315Dmm ■ weight: -- 8kg ■ Tube cover、Wooden side plates, AC cable* Resistors are KOA Made in Japan and capacitors are Mundorf made in Germany

[TRX-P6L] tube power amplifier■ Class AB Push Pull ■ Tubes: 6L6GC x 4、 12AX7 x 2、 12BH7 x 2■ Automatic Bias ■ Output power: 6L6GC - UL @ 25 W, Triode @ 12 W

KT-88 - UL @ 30 W, Triode @ 15 WEL-34 - UL @ 30 W, Triode @ 15 W

■ Frequency response: 10HZ - 100KHz ■ S/N ratio: 90Db■ Input Sensitivity: 600 mV ■ Input Impedance: 100 K Ohm ■ Input Gain; 0, - 3, -6dB■ NFB : 0, 3, 6 dB ■ Input terminal: RCA ■ Out Terminal: 4, 6, 8 Ohms■ Power Consumption no Signal:100W max ■ Dim: W340 x D315 x H187 ( mm)■ Weight: 15 Kilos* Resistors are KOA Made in Japan and capacitors are Mundorf made in Germany

NEW MODEL[TRX-PM84] tube integrated amplifier with remote controlThis is the newest Integrated Amplifier designed by Junichi Yamazaki of Triode Corporation-Japan. It is a 15 watts perchannel using EL84 tubes. It create a delicate and holographic sound with the ability to convey a deep, detailed andrich character of the instrument. Lightning quick in response and the ability to deliver minute details in the recordingwill easily suck you into the music. The newly designed EI- Orient Core Output transformer creates thundering quickbass, big soundstage and incredible details makes this amplifier one of its kind.

The First Tube Integrated Amplifier with built in USB DAC, USB Memory, Headphone and MM phono stage. It uses the6BQ5/ EL84 tubes which outputs 15 watts per channel in Push Pull. It has also a Bass and Treble control and remotecontrol. It is basicaly one of its kind with s traditional Triode sound and beauty. DAC: Burr-Brown made PCM 1798, 24bit 192 KHz PC-USB (Type B ): Accepts :16 / 24 bit, 32 KHz / 44.1 KHz / 48 KHz / 88.2 KHz / 96 KHzUSB Memory (Type A ): Accepts MP3 / AAC / WMA · 32 KHz / 44.1 KHz / 48 kHzSpecifications:■ Circuit type: 6BQ5 (EL84) AB class Push-Pull ■ Rated Output: 15W +15 W (8Ω) ■ SN ratio: 87dB■ Frequency Response: 15Hz ~ 50 kHz ( ± 1dB ) ■ Input sensitivity: Line / 290 mV · 100kΩ, MM/10mV · 47 KΩ■ Input: MM phono system x 1, Line in x 2, PC-USB (Type B ) x 1 system, USB memory (Type A ) x1

■ Output: x1 Speaker system (4 ~ 8Ω), Headphone jack ( vacuum tube circuits )■ Vacuum tube: Output tube 6BQ5 x 4, first stage 12AX7 x 1 , driver 12AU7 x 2■ Power Consumption: 130 W ■ Dimensions: (W) 12 inches x (H) 6.1 inches x (D) 10.3 inches. ■ Weight: 12.2 kg

NEW MODEL[TRX-M845]845 Drive 845 parralel single-ended mono power amplifier■ Maximum output: -- A class 50W (8ohms) Automatic bias ■ Output tube: -- 845 parralel single -ended■ Tubes: 845 * 3 , 6SN7 * 1, 12AU7 *1 (211 * 2) ■ Output impedance 4 / 6 / 8 / 16 ohms■ Input : RCA * 1 / XLR * 1 (switch #2 #3 ) ■ KOA highly precise resistor use■ NFB : 0 , 1 , 3 dB switched ■ Hi qualityl capacitor use ■ Frequency response 10Hz- 50 kHz ( -2 dB)■ Total distortion < 0.1%(1kHz) ■ SN level 89dB ■ Input sencitivity 0.9V■ Power sanction 280 watts ■ Demention:580W x300H x 440Dmm ■ Weight: 55kg■ Tube cover, AC cable, Fuses