5+

8335

5 - W

M

P r o b l e m S o l u t i o n

Does not turn on orwork abnormally

Does not respond to your voice

Does not accept tablet programming

Does not walkproperly

Does not sit or jump

Bone does not light up during feeding

Check to see if his batteries are dead. Replace if necessary.

TEKNO™’s sound sensors are set up for normal speech and sounds. Try talking louder or clap your hands to get his attention. If the environment is too noisy, TEKNO™ is confused.

Try to turn up the volume on the Tablet or move it closer to TEKNO™. TEKNO™ responds best if less than 18 inches (46cm) from the Tablet. Make sure he is in the correct mode to respond to Tablet commands.Noisy background will affect communication between TEKNO™ andtablet. Keep environment quiet when using TEKNO™ app feature.

Make sure that he has a clear path from in front of his eyes. His optical sensorsautomatically stop him from walking if he gets close to objects.TEKNO™ walks best on non-carpeted hard surface. (Not on glass surface.) Make sure TEKNO™ is already in the Gesture Mode, by holding your hand before his eyes and you already hear the ‘beep’ sounds.NOTE: you can use the alternative method to get into the Gesture mode as mentioned previously.Move your hand closer in front of TEKNO™’s eyes, slowly DOWN and UP to make sure he sees your hand.Make sure TEKNO™ sits completely on floor, when you hear warning buzzer noise he is not sitting on a flat surface. Place TEKNO™ on a flatter surface to try. Similarly he will not jump either if he is holding the ball or any other object under his chin.

Make sure the arrow on the bone is pointing up towards under his chin. Move the bone around his lower jaw and see if you can find the correct area to activate the bone. If this does not work, replace the batteries in the bone.

™

TEKNO™ is a real robot who responds to your voice, actions, motions, lights, sounds and even an app on your Apple® iPad®

or tablet of Android™ device. Thanks to his artificial intelligence program, TEKNO™ will bark, cry, whine and change his eye patterns in ways to show how he's feeling.

TEKNO™ has state-of-the-art sensors to know if he's being pet, fed, talked to, and played with. In short, he acts just like a real puppy.

TEKNO™ features the latest in Robotic Technology: HAND GESTURING CONTROL. With simple movements of your hand, you can command TEKNO™ to stop, sit, and do a back flip jump. But, deep inside his programming, TEKNO™ is still an 8 week old puppy.

BATTERIES

NOTE: The Bone comes with the batteries already installed. There is no “on/off” switch as the batteries work only when feeding TEKNO™.

However, if you need to replace the 3 AG13/LR44batteries, follow this direction.

Follow the instructions included in this manual and learn more about how to care for TEKNO™ – your robotic friend.

AG131.5V

AG131.5V

AG131.5V

AA

1.5

VA

A 1

.5V

AA

1.5

VA

A 1

.5V

LIGHT SENSOR

SOUND SENSOR

TOUCH

SENSORSOTHER

SENSORS

NOSE SENSOR

MOUTH SENSOR

GESTURE SENSORHEAD SENSOR

POWER Push this buttonto turn ON / OFF

MODE BUTTONS See sect ion on programming

HEAD POSITION SENSOR

LEG POSITIONSENSOR

EAR POSITIONSENSOR

Learning all of TEKNO™’s sensors will help you to keep him happy.

Get To Know TEKNO™

Get To Know TEKNO™Basic TrainingPOWER SWITCH >> This is the main switch of TEKNO™. Press to power ON, press again for OFF.

HEAD SENSOR >> This invisible sensor is used to reward and thank TEKNO™. When you pat or rub TEKNO™ on the top of his head, he will become very happy. Or when he is too excited, patting his head will calm him down to listen to you and follow your command.

LIGHT LEVEL SENSOR >> Located under his black sunglasses. This responds to changes in light levels. This lets TEKNO™ know the amount of light in the room.

EAR POSITION SENSOR >>This sensor helps you to understand TEKNO™’s emotional state. TEKNO™’s computer brain decides his emotional state at all times and will move his ears to the correct position. Just like a real puppy, TEKNO™ may perk up his ears when he is surprised or drop them low when he is sad.

GESTURE SENSOR >>This sensor lets TEKNO™ actually “see” the motion and position of your hands in front of his eyes.

SOUND SENSOR >>Located on the side of his head, this allows TEKNO™ to hear sounds. His computer will interpret these sounds in a similar manner as a real puppy by use of his artificial intelligence program. As he is still a baby puppy, he cannot identify the sound is from people talking or background noise yet.

MOUTH SENSOR >>This is an invisible sensor located in TEKNO™’s chin. This lets TEKNO™ know when he is being fed or holding his special TEKNO™ ball.

NOSE SENSOR >> When pressed, this sensor makes TEKNO™ sniff. It will also cause TEKNO™ to stop walking if he runs into an object.

TEKNO™ will then immediately begin to sense and explore when his power button is pressed.

GESTURE TRAINING

PROGRAMMING

ADVANCED PROGRAMMING

TROUBLE SHOOTING / HINT

emotions

TEKNO™ needs to be in a good preparation before gesture training. Make sure he is in ready condition for gesture. Let him complete his current action and keep quiet for a few seconds. You can know from his eyes when he is ready (see pic). Hold your hand in front of TEKNO™’s eyes at least 3 seconds. It’s best to be within about 3 inches (7.5cm) away to make sure he clearly sees your hand when he is not walking. You will hear “beep” sounds when he goes into the mode successfully.If you hold your hand over 10 second but TEKNO™ gives no response, you need to retry. HINT 1: TEKNO™ sees your hand as an obstacle when he is walking. He will not get into the gesture mode because it is not safe for him to jump. After making him stop, your hand has to move away from his eyes for 3 seconds then put back again to give him the correct hand command.

SIT! First let him sit. Move your hand DOWN smoothly in front of his eyes. If you do this correctly, TEKNO™ will sit.

FLIP! From this sitting position, move your hand UP smoothly in front of his eyes and he will do a backflip and bark.HINT2: In this mode do not shake your hand. Give firm command to TEKNO™, otherwise he might be confused of what to do. You may need to have more practices with TEKNO™ together to make him flip successfully. HINT3: If TEKNO™ does not sit properly, TEKNO™ is not ready to flip and will not respond to your hand-up (FLIP) command. You will hear alarm sounds from TEKNO™ to remind you. Move him to a flat surface and retry FLIP command to let him flip.

How to keep TEKNO™ happyTEKNO™ needs attention to be happy. Just like a real puppy, it is important to play with him and not forget to take care of him. He needs stimulation to be happy such as patting or rubbing him on the head, talking to him, or clapping your hands. You will see his ears move, his eyes flash, his tail wag, and he will happily walk seeking adventure. You should also remember to feed him with his energy bone at least once a day. You can feed him more if you like. TEKNO™ always likes to eat.

What makes TEKNO™ unhappyNot feeding, petting and playing with him or left him for a long time. TEKNO™ shows you that he is unhappy by crying and moaning, his ears go down, and his eyes display a sad pattern.

ALKALINE BATTERIES RECOMMENDED

PUPPY USES 4 X [ AA / LR6 ] BATTERIES(NOT INCLUDED).

BONE USES 3 X [ AG13 / LR44 ] BATTERIES(INCLUDED).

Unscrew the battery door as shown. Insert 4 AA / LR6 alkaline batteries (not included) and replace the battery door.

http://www.youtube.com/teknoroboticsSEE A VIDEO OF HOW TEKNO™ WORKS ON

http://www.youtube.com/teknoroboticsSEE A VIDEO OF HOW TEKNO™ WORKS ON

http://www.youtube.com/teknoroboticsSEE A VIDEO OF HOW TEKNO™ WORKS ON

http://www.youtube.com/teknoroboticsSEE A VIDEO OF HOW TEKNO™ WORKS ON

http://www.youtube.com/teknoroboticsSEE A VIDEO OF HOW TEKNO™ WORKS ON

http://www.youtube.com/teknoroboticsSEE A VIDEO OF HOW TEKNO™ WORKS ON

An alternative way to get into gesture mode is to press and hold down the and buttons at the same time for 3 seconds. You will hear “beep” sounds.

Battery Warnings:Important! Only adults should replace batteries.Alkaline batteries are recommended.Do not use rechargeable batteries.Non-rechargeable batteries are not to be recharged.Do not mix old and new batteries.Do not mix alkaline, standard (carbon-zinc), or rechargeable(nickel-cadmium) batteries.Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity.Exhausted batteries are to be removed from the toy.The supply terminals are not to be short-circuited. Please keep this information for future reference.Remove batteries from the product before extended storage.

DO NOT lift up TEKNO™ when he is sitting, you will hear alarm sounds also and you should put him back to floor to allow him to complete the ‘training’ with a flip.CAUTION: If TEKNO™ sits for 30 seconds without jumping, he will jump automatically. TEKNO™ will give several “ding” sounds first and then jump.To avoid serious injury, don’t approach closely to the TEKNO™ when flipping.

FRONT

BACK

TEKNO™ is amazingly smart and he is easy to program. There are 2 MODE BUTTONS on TEKNO™’s head.

Let you have a conversation with TEKNO™.

In this mode, TEKNO™ will listen to what you say and talk back to you. He will hear what you say and will respond back in as best he can in barks and sounds.

TEKNO™ will not walk in this mode. So, it’s a good way to play and talk with him on a tabletop or desk.

Here’s how to start:• Press Mode Button .• You will hear a “ding”sounds, see TEKNO™

perks up his ears. NOTE: DON’T TOUCH ANY OTHER SENSOR OR HE

WILL GO BACK TO HIS NORMAL MODE.

• Now talk to TEKNO™. When you stop talking, wait a moment and listen to him talking back to you. He’ll do this as long as you like.

• When you want to stop this mode, simply pat his head or press his nose.

HINTS 1) If the environment is too noisy or many people are talking, TEKNO™ will keep listening until you stop, then he will talk back to you.

2) TEKNO™ prefers this mode when he is left alone, i.e. he is automatically in this mode. You need to draw his attention by patting his head, or pressing his nose to get out of this mode.

Let you selecting a song and dance routine.

Here’s how to start:• Press and release button to enter this mode. • You will hear a “ding” sound.• You can select one of two songs for

TEKNO™ to move to:• For song 1: Press the button ONCE and you

will hear one “ding”sounds. Clap your hands to start him.

• For song 2, Press the button TWICE. You will hear two “ding”sounds. Clap your hands to start him.

• To make him stop while dancing, pat him on his head or press his nose.

CONVERSATION MODE SING & DANCE MODE

MODE BUTTON MODE BUTTON

Tablet Programing ModeDownload the TEKNO™ app into your tablet and follow the instructions included in the app.

When you’ve read the instructions and are ready to program TEKNO™ from your tablet:

• PRESS and HOLD Mode Button until you see TEKNO™’s eyes flash with all color.NOTE: DON’T TOUCH ANY BUTTONS OR HE WILL GO BACK TO HIS NORMAL MODE.

• START UPLOADING your program from tablet. TEKNO™ will await 1 minute for you to start. If he does not receive a program command in 1 minute, he will get out of this mode, and go back to his normal mode to play with other people or sounds.

Get the TEKNO™ app from Apple® App Store or Google Play™, follow the in-appinstructions to have more fun with TEKNO™.Works with iPad® series. iOS 5.0 or above.Works with tablets for Android™ 3.0 platform or above.See details in app description.

TEKNO™ shows his feelings with his eyes. Here’re only some examples.

HINT: When programming TEKNO™ with a Tablet, turn the volume UP on the Tablet to the maximum. For best performance, keep the Tablet within 18 inches (46cm) from TEKNO™'s head.Noisy background will affect communication between TEKNO™ and tablet. Keep environmentquiet when using TEKNO™ app feature.

HINT: Press his nose to exit this tablet mode.

NOTE: Toy Quest is not responsible for any content distributed through the App store except for Toy Quest generated content. Please refer to Apple® Inc.’s terms and condition for further information.

Android™ is a trademark of Google Inc.

READY!

WARNING: Read all instructions before use.Adult supervision required at all times.Adult should instruct children on proper use of the TEKNO™.To avoid serious injury, don't approach closely to the TEKNO™ when flipping.Keep away from fire.Do not immerse TEKNO™ in water. Play on smooth and flat surface.Use only the provided accessories.Do not modify TEKNO™ from its original design.

Please retain this information for future reference. Colors and content may vary.

PUTOU INDUSTRIAL AREA,HUZHEN TOWN, BOLUO,HUIZHOU, CHINAALL RIGHTS RESERVED

MADE IN CHINAwww.toysinquiry.com

DO NOT RETURN TO STORETHIS PRODUCT CANNOT BE RETURNED

FOR A REFUND AFTERIT HAS BEEN UNPACKED AND USED.

FOR QUESTIONS OR PROBLEMS WITH THIS PRODUCTPLEASE VISIT BELOW CUSTOMER SERVICE WEBSITE

FOR EXPEDITED ASSISTANCE

www.toysinquiry.comOR

1 - 8 0 0 - 4 3 4 - 6 1 7 8

- “This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.”

- “Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.”

- “NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and

receiver.• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.”

HINT: Turn off TEKNO™ power before storage.

EATING: Take the bone and place the edge with the arrow up sign under his chin. TEKNO™ will begin to chew the bone. The bone will light up and look like he is “charging”. But when he is full, he may not chew the bone anymore or the bone does not light up.

CURIOSITY: TEKNO™ is very curious. If you press anything against his nose, he will sniff it.

PLAYING: Place the ball under his chin and it will stick in place, sometimes he will chew the ball and beg you to remove it.

TRAINING: TEKNO™ is just a puppy, he may bark or walk to any sound. You can pat his head to let TEKNO™ know you are there and follow your command.

ON/OFF

Push this button to turn on and off

www.tekno-robotics.comPlease visit:

for more information