training catalog - automated logic corporation · 10 bas university training catalog 2020 11...

14
BAS University Training Catalog 2020 TRAINING CATALOG An educated customer is a happy customer.

Upload: others

Post on 20-Jun-2020

5 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

BAS University Training Catalog 2020

TRAINING CATALOG

An educated customer is a happy customer.

Page 2: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

2 3BAS University Training Catalog 2020 BAS University Training Catalog 2020

© 2020 Automated Logic Corporation.

The contents of this catalog and the associated Automated Logic® software are property of Automated Logic Corporation and its respective licensors, and are protected by copyright. For more information on the software and licensing, see the About section in the software’s Help menu.

Automated Logic, WebCTRL, EIKON, Eco-Screen, and BACview are registered trademarks of Automated Logic Corporation. EnergyReports and Environmental Index are trademarks of Automated Logic Corporation. BACnet is a registered trademark of ASHRAE. All other trademarks are the property of their respective owners.

The content of this catalog is furnished for informational use only and is subject to change without notice. Automated Logic Corporation assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content contained in this guide.

About our Training ...........................4

Certification Tracks ..........................6

Training Formats ............................13

Course Listing ..................................14

Table of Contents

Page 3: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

4 5BAS University Training Catalog 2020 BAS University Training Catalog 2020

About Automated Logic Training

Automated Logic offers hands-on, task-based learning opportunities, as well as interactive / online training for owners,

operators, and field office personnel. Located on the Automated Logic - WHQ campus in Kennesaw, GA, on-campus courses

include a tour of the manufacturing floor and the opportunity to meet Automated Logic staff. Frequently, members of the

Product Office, R&D, Sales, and Tech Support will sit in on a class, or simply join students for lunch to further our commitment

to hearing the voice of the customer.

While there are many benefits to attending courses on the main campus in Kennesaw, GA, learning can take place in many

shapes, forms, and locations.

About Us Our Training

Choose from:

Automated Logic World Headquarters (WHQ),

Kennesaw, GA - learn from factory instructors who have

gone through a rigorous, multi-step qualification process

before being permitted to instruct students. Instructor-led

training through WHQ is IACET CEU eligible.

Factory Certified Gold Partners in Training - learn

from factory certified instructors who are vetted using

the same process as WHQ factory instructors, and their

classrooms are required to meet the same standard as

WHQ. These locations will be indicated by the “Gold” label

and certifications are instructor/course specific.

Bronze or Silver Partners in Training - learn from

a wide range of individuals who have seen the course

presented, and are using material developed by WHQ. These

locations will be indicated by either a “Bronze” or “Silver”

label.

Accredited Provider

IACET

Automated Logic offers IACET CEUs with select courses and

locations. Contact your local, authorized, Automated Logic

provider for details.

Automated Logic is an accredited provider of the

International Association for Continuing Education and

Training (IACET), 2201 Cooperative Way, Suite 600,

Herndon, VA 20171; 703-234-4065.

Partners in Training

In addition to training at our WHQ location in

Kennesaw, GA, we’re pleased to offer training

through our Partners in Training in the following

additional locations:

North America

Los Angeles, CA

Chicopee, MA

Clifton, NJ

Harrisburg, PA

Las Vegas, NV

Lisle, IL

Pasadena, TX

Pittsburgh, PA

Pleasanton, CA

Sacramento, CA

San Diego, CA

Mississauga, Canada

We’re so excited you’re turning to Automated

Logic for your training needs! We believe

educated customers are happy customers,

and we want happy customers! Consequently,

we’re constantly working toward growing

our curriculum so we can help you grow your

business through a well-educated, satisfied

customer. We offer plenty of courses for

both end user customers and field office

personnel, with many more to come. We’re

looking forward to sharing our knowledge

with YOU!

Automated Logic Training Team

Reading help files - all Automated Logic product has

comprehensive written documentation. Authorized

Automated Logic dealerships can access this information

from accounts.automatedlogic.com.

Watching online video tutorials - many of the

proprietary product features have associated video

tutorials, and more are being added to our online Learning

Management System (LMS), regularly. Authorized Automated

Logic dealerships have access to the LMS by selecting the

LMS link from the accounts website > Training > Home page.

International

Middle East

Africa

Europe

Latin America

India

Asia Pacific

Contact Us

Contact your local, authorized, Automated Logic provider

for course pricing and schedules. For questions about

Automated Logic Training, please email us at training@

automatedlogic.com.

Alternatively, you may call our Training Coordinator at

770-795-5188.

Page 4: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

6 7BAS University Training Catalog 2020 BAS University Training Catalog 2020

Certification Tracks

Owner/Operator

The Owner/Operator certification track is for

customers who would like to learn how to use

the capabilities and features of the WebCTRL®

system to effectively manage and maintain their

facility, regardless of industry type or size. All

courses are available a la carte (note, some do

require prerequisites), but the most balanced,

comprehensive training will come by following the

certification track that most closely resembles your

job description.

Associate Owner/Operator

The Owner/Operator Associate certification program is

designed for owner/operators who are new to a WebCTRL

system. Participants will be able to connect to a live

WebCTRL system to interact, set up, and maintain their

building, and walk away with an understanding of schedules,

trends, alarms, and other fundamental WebCTRL features to

maximize their building automation purchase.

Required Courses

WebCTRL - Basic (WC-200)

Owner/Operator Associate

Annual Renewal (TBD)

Certification Tracks

Master Owner/Operator

The Owner/Operator Master certification program is

designed for owner/operators who want more than the

intermediate, working knowledge of a WebCTRL system and

would like to enhance their skills with the entire WebCTRL

application suite including the EIKON® tool, SiteBuilder and

ViewBuilder. Certified Owner/Operator Masters will know

how to add new or edit existing equipment and areas to

their system while creating custom programs and graphics.

Networking standards, as well as how to troubleshoot

advanced networking issues on their WebCTRL system are

also included.

Practitioner Owner/Operator

The Owner/Operator Practitioner certification program is

designed for owner/operators who want more than the

basic, working knowledge of a WebCTRL system and would

like to learn about its progressive features, such as advanced

reporting, advanced security, alarm actions, and WebCTRL

add-ons. Upon completion of courses in this certification

track, students will be able to diagnose and troubleshoot

their WebCTRL system using WebCTRL alarms, trends,

reports, and live logic pages.

Required Courses

Owner/Operator Associate Certificate

WebCTRL - Intermediate (WC-300)

Field Tech - Operator (FTO-200)

Owner/Operator Practitioner

Annual Renewal (TBD)

Required Courses

Owner/Operator Practitioner Certificate

EIKON - Basic (EIK-200)

ViewBuilder - Basic (VB-200)

Networking - Basic (NET-200)

Owner/Operator Master

Annual Renewal (TBD)

Page 5: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

8 9BAS University Training Catalog 2020 BAS University Training Catalog 2020

Certification Tracks

Field Technician

The Field Technician certification track is for field

office personnel, whether from an independent

dealership or an Automated Logic branch, seeking

skills to better prepare them for obstacles they may

face in the field. Courses in this certification track

will prepare field technicians and field engineers to

confidently install, commission, troubleshoot, and

edit WebCTRL systems so that contracts are more

likely completed on time, on budget, and with a

satisfied customer.

Associate Field Technician

The Field Technician Associate certification track is designed

for field technicians who are new to a WebCTRL system and

HVAC. When certified, a Certified Field Technician Associate

will be able to diagnose, troubleshoot, and edit issues with

programming, graphics, networks, and system architecture.

Topics covered include all applications that make up a

WebCTRL system.

Required Courses

WebCTRL - Basic (WC-200)

Field Technician - Basic (FT-200)

EIKON - Basic (EIK-200)

ViewBuilder - Basic (VB-200)

Networking - Basic (NET-200)

Commissioning - Intermediate

(COMM-300)

Field Technician Associate

Annual Renewal (TBD)

Certification Tracks

Master Field Technician

The Field Technician Master certification track is designed

for field technicians who need to understand the most

complex features, options, and theories associated with the

Automated Logic product or systems required to use the

Automated Logic product. Topics included are advanced

programming and graphics, design engineering, complex

networks, robust databases, and custom add-ons for a

WebCTRL system. Special guest speakers and subject matter

experts will appear in many of these classes.

Practitioner Field Technician

The Field Technician Practitioner certification track is

designed for field technicians who require the skills to

create custom programming and graphics, add complete

mechanical systems to the WebCTRL system, and

troubleshoot common networking issues using sniffer

tools such as Wireshark®. Many advanced theories, tips,

and strategies are discussed in these courses, including

WebCTRL add-ons, WebCTRL security, and database

integrity. Along with commissioning, troubleshooting, and

fine-tuning a WebCTRL system, a Certified Field Technician

Practitioner will be proficient with the integration of BACnet®

and Modbus® devices.

Required Courses

Field Technician Associate Certificate

WebCTRL - Intermediate (WC-300)

EIKON - Intermediate (EIK-300)

ViewBuilder - Intermediate (VB-300)

Networking - Intermediate (NET-300)

Third Party Integration BACnet (BAC-300)

Third Party Integration Modbus (MOD-300)

Field Technician Practitioner

Annual Renewal (TBD)

Required Courses

Field Technician Practitioner Certificate

Field Technician Master

Annual Renewal (TBD)

Page 6: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

10 11BAS University Training Catalog 2020 BAS University Training Catalog 2020

Certification Tracks

Design Engineer

The Design Engineer certification track is for

Automated Logic branch and independent field

office personnel, which is intended to produce a

design engineer with the proactive skills to foresee

potential issues prior to turning a project over to

the field technician. Sometimes known as “cradle

to grave” engineering, a design engineer may see

a project from creation, requested changes, and

final as-builts throughout the entire lifespan of

the contract. With emphasis on building a solid

foundation with standards, design engineers can

work together with field technicians to ultimately

deliver a quality product within a scheduled

timeframe and projected budget.

Associate Design Engineer

The Design Engineer Associate certification track was

developed for design engineers who are new to a WebCTRL

system and HVAC. The Certified Design Engineer Associate

will be able to design basic IP and ARC156 networks utilizing

standards that allow for future growth. Engineers will create

complete system databases with SiteBuilder while producing

programs and graphics for areas and equipment. Utilizing

Automated Logic’s Engineering Design Suite, associates will

become fluent in selecting hardware, standard naming and

numbering structure, and creating control drawings.

Required Courses

WebCTRL - Basic (WC-200)

EIKON - Basic (EIK-200)

ViewBuilder - Basic (VB-200)

Networking - Basic (NET-200)

Design Engineering - Basic (DE-200)

Design Engineer Associate

Annual Renewal (TBD)

Certification Tracks

Master Design Engineer

The Design Engineer Master Certification track is the final

path for design engineers. Topics included are advanced

programming and graphics, design engineering, robust

databases, third party integration, and cost saving strategies.

No feature, option, or theory is off limits at this point. Special

guest speakers and subject matter experts will likely make

an appearance in these classes.

Practitioner Design Engineer

The Design Engineer Practitioner certification track is

designed for design engineers who require the skills to

create custom programming and graphics, design complex

WebCTRL systems, and create control drawings. Many

advanced theories, tips, and strategies are discussed in

these courses, including WebCTRL add-ons, WebCTRL

security, and database integrity. Other topics included are

common networking issues, SQL databases, and deciphering

Wireshark. Certified Design Engineer Practitioners will also

gain the knowledge of customizing the Engineering Design

Suite using the Administration tool.

Required Courses

Design Engineer Associate Certificate

EIKON - Intermediate (EIK-300)

ViewBuilder - Intermediate (VB-300)

Networking - Intermediate (NET-300)

Third Party Integration BACnet (BAC-300)

Third Party Integration Modbus (MOD-300)

Design Engineer Practitioner

Annual Renewal (TBD)

Required Courses

Design Engineer Practitioner Certificate

Design Engineer Master Annual

Renewal (TBD)

Page 7: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

12 13BAS University Training Catalog 2020 BAS University Training Catalog 2020

Certification Tracks

Annual Renewal Certification Tracks

The courses listed have been identified as required for

certification at the time of publication and will be reviewed

and updated annually at a minimum.

Equally important to becoming certified is the necessity

to stay current, whether by learning something new or by

simply refreshing skills you’ve already learned.

If there is no new content relevant to your certification track,

simply log in to the Building Automation System University

(BASU) Learning Management System (LMS) and take the

corresponding online exam to extend your certification

through the end of the following year. If there is new

content, whether due to new product, previously untaught

content, or new supporting technology, an annual renewal

course or courses will be added to each certification track.

In most cases, annual renewal courses will be in the form

of a What’s New video, which will include the factory

certification exam. Passing the factory certified annual

renewal exam will extend your certification to the end of the

following year. These online courses and the corresponding

exams will be available online through the BASU LMS.

In some cases, however, especially for more advanced

training or training requiring hands-on hardware, an in-

person, instructor-led course may be necessary.

Regardless of how content is delivered, continuing your

education by regularly completing the annual renewal

courses will ensure you aren’t missing out on new, and

sometimes powerful features of your building automation

purchase, nor are you missing out on advances in

supporting technology that could vastly change how you

do business.

Course Names Understanding the Course Listing Section

Courses offered by BASU follow the below naming

convention. In this example, this is a Basic (level 200

difficulty) EIKON course taught using EIKON v6.0.

The product version number will only be used when

referencing a specific instance of a course. For example,

EIK200 will be listed in the certification tracks, but would

reference EIK-206.0 when the student takes the course.

COURSE ID

EIK-206.0

Product/ course name

Product version number

Course level/ difficulty

Training Formats

Instructor Led Live instructor in real time

Classroom In-house - whether you

visit BASU-WHQ in Kennesaw, GA, or visit

another of our Gold Partners in Training

locations, a live instructor will lead up to 12

students (course dependent) in task-based,

hands-on exercises with minimal lecture in between. Using

the situated learning techniques of the Kirkpatrick Model,

BASU Factory and Factory Certified Gold Partners in Training

instructors behave as a “guide by your side” vs. a “sage on

the stage.” This methodology fosters a collaborative learning

environment where learners are not only successful

in the classroom, but are positioned to maximize

knowledge retention.

Classroom On-site - exactly the same

setup as the classroom in-house training,

this option brings the classroom to you.

Scheduled through the local field office in

coordination with BASU-HQ. Pricing and

availability vary by course.

One-on-one Coaching - courses taught

in this manner pair one student with one

Factory or Factory Certified Gold Partners

in Training instructor using remote access

software. This connection allows the

learner to take control of the instructor’s workstation from

the convenience of their home or office, giving them an

individualized virtual classroom experience from many miles

or time zones away.

Self-Paced No instructor involvement

Self-paced video tutorials - another

distance learning option for some courses,

the self-paced video tutorials allow the

learner to watch and re-watch videos at

their own pace. This option is a good

option for those who would like a refresher on what

they’ve learned elsewhere, or as a prerequisite to another

course. Not recommended as the only means of learning

something new.

The following video tutorials are self-paced and available

24/7/365.

Hybrid Live instructor as needed

Virtual Classroom - another distance

learning option for some courses, the virtual

classroom allows the learner to take up

to 14 days to complete the instructor-led

classroom equivalent of a 1-3 day course.

Using video tutorials as the on-demand instructor, learners

will execute the workbook tasks and upload assignments

using the BASU LMS, asking questions through the

discussion board where a dedicated Factory or Factory

Certified instructor will facilitate.

FORMAT

Classroom

FORMAT

Self-Paced

FORMAT

Virtual

FORMAT

On-site

FORMAT

1-on-1

Page 8: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

14 15BAS University Training Catalog 2020 BAS University Training Catalog 2020

Course Listing

Best Practices in Training

This course is for learners looking to instruct Automated

Logic’s factory certified 200 level courses and is a necessary

step to participate in our Partners in Training program. The

course includes situated learning techniques as supported

by the four levels of the Kirkpatrick Model, as well as learning

professional presentation skills and techniques proven

effective for adult education. This course is only open to

Automated Logic branch and independent field office

personnel.

While there are no course prerequisites, management from

the candidate’s field office must contact BASU’s Training

Manager to discuss PIT program requirements prior to

candidate registration.

Design Engineer – Basic

The foundation of every project starts here. This Design

Engineering course will introduce the basic fundamentals

of creating a complete WebCTRL system package to a field

technician for installation. Learners will be challenged by

completing a WebCTRL system throughout the entire project

life cycle. The project life cycle will include the project scope,

review of hardware, a control submittal developed with

Engineering Design Suite, and creating a WebCTRL system

database. This course strongly encourages the use of

standards, the creation of libraries, and the optimal use of an

engineer’s time. With these skills the objective of the Design

Engineer becomes clear: deliver on time, under budget, and

mistake free. This course is for Automated Logic branch and

independent field office personnel only.

Commissioning - Intermediate

This course is designed to challenge the field technician with

all aspects of a WebCTRL system. Upon completion of this

course, the learner will be able to install and commission

a WebCTRL system, provide functional testing of a control

program, and apply the most advanced techniques of

troubleshooting. The learner will also be responsible for

turning in complete check out reports, installing add-ons,

and correcting an entire system of common errors, including

some obscure “gotchas,” using all the skills the learner

acquired in WebCTRL, Eikon, ViewBuilder, SiteBuilder, and

EquipmentBuilder.

COURSE ID

TRN-300

FORMAT/LENGTH

Classroom/2 Days

CEUs

1.6

PREREQ

N/A

COURSE ID

COMM-300

FORMAT/LENGTH

Classroom/4 Days

CEUs

3.2

PREREQ

WC-200 FT-200 EIK-200 VB-200

NET-200

COURSE ID

DE-200

FORMAT/LENGTH

Classroom/4 Days

CEUs

3.2

PREREQ

N/A

COURSE ID

EIK-300

FORMAT/LENGTH

Classroom/3 Days On-site/3 Days

CEUs

2.4

PREREQ

EIK-200 or FT-200

+ 6 months experiences after completing

In addition to the prerequisite courses listed, the learner is

expected to also have a minimum of 6 months – 1 year

field experience.

Course Listing

EIKON - Intermediate

Whether a Field Technician or Design Engineer, learners

will expand on knowledge from the EIKON - Basic course

to learn how to create complex control programs and logic

symbols. The learners will be able to identify programming

as it is implemented within a complete system. The learners

will also be able to utilize naming standards to create a

library for quickly placing previously developed logic into

new systems, thus making programming more efficient.

Building a properties page, simulating a control program,

major customization to EquipmentBuilder programs are

among several other intermediate EIKON features offered

in this course.

COURSE ID

EDS-300

FORMAT/LENGTH

Classroom/2 Days Virtual/Up to 10 Days

CEUs

1.6

PREREQ

Microsoft Visio Proficiency

Engineering Design Suite (EDS)

The Microsoft Visio® EDS add-on is a tool that allows you

to streamline engineering tasks and the submittal process

to make drawings for installing and commissioning, create

project reports, and control your revisions. The add-on

includes built-in components with data sheets, engineering

calculators and conversions, Cv calculations for water and

steam, a building riser manager, a valve schedule creator,

and a searchable library in which you can add items.

Data can be output to Microsoft Excel® in standalone

spreadsheets or embedded in the Visio® EDS drawings. It

provides automated creation of sequence of operation and

your final drawing package.

COURSE ID

EIK-200

FORMAT/LENGTH

Classroom/2 Days Virtual/Up to 10 Days

CEUs

1.6

PREREQ

N/A

EIKON - Basic

Learn the basics of EIKON programming. Learners who

successfully complete this course will be able to identify

the different types of microblocks, read a sequence of

operations and translate to a program, simulate a program

to find errors, and define microblock properties.

To take the class virtually, you must have the latest version

of EIKON installed on your computer.

Page 9: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

16 17BAS University Training Catalog 2020 BAS University Training Catalog 2020

HVAC Advanced for DDC for Technicians

Taught by Tempcon, Inc., this course is designed for DDC

technicians with some experience in HVAC systems who

need to enhance their understanding of the more complex,

“built-up” HVAC systems and control strategies. This course

will expand beyond the 2-year technical school HVAC course,

so that learners may gain an excellent working knowledge of

advanced HVAC and DDC control systems.

Field Tech Operator

Designed for WebCTRL system owners/operators, this

course covers many of the same skills and techniques taught

in the Automated Logic Field Technician Basic course, such

as installing, basic commissioning, and troubleshooting a

WebCTRL system. Upon successful completion of the course,

learners will be able to apply these skills, as well as edit a

WebCTRL system utilizing EIKON, SiteBuilder, ViewBuilder,

and WebCTRL.

Course Listing

HVAC/DDC for Non-Technicians

Taught by Tempcon, Inc., this course is designed for non-

technicians with basic knowledge of HVAC systems who

need to enhance their understanding of the more complex

HVAC systems and processes. Learners who successfully

complete this course will be able to gain an excellent working

knowledge of the processes, terminology, and systems

found in more sophisticated institutional HVAC systems.

Networking - Basic

This course covers setup and troubleshooting techniques

affiliated with basic Automated Logic networks. In addition,

learners will build source trees, define and identify the

fundamentals of IP, ARC156, and MS/TP networks, and how

these concepts allow devices to communicate. Learners

will also learn the basics of Wireshark captures, clippings,

and BACnet Discovery. Upon successful completion of

this course, learners will be able to properly set up and

troubleshoot basic Automated Logic networks, including the

use of Wireshark captures to capture IP traffic at the server,

IP and ARC156 traffic at devices.

Course Listing

OEM Technician Training

This course is part of an initiative to increase service

opportunities working directly with OEM manufacturers.

Upon successful completion of this course, learners will

be able to directly connect to OEM control modules for

configuring standalone applications using Apploader and

Virtual BACview®. Learners will also be able to identify the

levels of permission keys, which provide access to the

programming and graphics for seamless native integration

to an Automated Logic system.

Networking - Intermediate

As part of successful course completion, learners will set up

complex ALC networks, troubleshoot networks, and create a

secure WebCTRL site. Learners will focus on troubleshooting

a WebCTRL system by reading a Wireshark capture. This

course is designed for individuals who need to design

complex network systems as well as troubleshoot networks

with Wireshark.

Field Tech - Basic

There are many different skill sets in the life of a field

technician - engineering, IT infrastructure, technical support,

and computer programming to name a few. Field Tech -

Basic training will prepare field technicians to confidently

install, commission, troubleshoot, and edit a WebCTRL

system utilizing EIKON, SiteBuilder, ViewBuilder, and

WebCTRL. Learners will become familiar with ISA submittal

control drawings and the mechanical equipment these

drawings represent. Hands on tasks include hardware,

networks, and software with an emphasis on real life

scenarios with the latest tools available.

COURSE ID

FT-200

FORMAT/LENGTH

Classroom/2 Days On-site/2 Days

CEUs

1.6

PREREQ

N/A

COURSE ID

HVAC-300

FORMAT/LENGTH

Classroom/4.5 Days

CEUs

N/A

PREREQ

N/ACOURSE ID

NET-200

FORMAT/LENGTH

Classroom/2 Days

CEUs

1.6

PREREQ

N/A

COURSE ID

OEM-300

FORMAT/LENGTH

Classroom/2 Days On-site/2 Days

CEUs

1.6

PREREQ

FT-200

COURSE ID

NET-300

FORMAT/LENGTH

Classroom/3 Days

CEUs

2.4

PREREQ

NET-200 + 6 months experience

COURSE ID

HVAC-200

FORMAT/LENGTH

Classroom/4.5 Days

CEUs

N/A

PREREQ

N/ACOURSE ID

FT0-200

FORMAT/LENGTH

Classroom/3 Days On-site/3 Days

CEUs

2.4

PREREQ

N/A

Page 10: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

18 19BAS University Training Catalog 2020 BAS University Training Catalog 2020

Course Listing Course Listing

ViewBuilder - Basic

This course introduces Automated Logic-supplied area and

equipment graphics. A complete ViewBuilder overview is

covered, as well as its tools, controls, images, and available

symbols. Custom topics include the use of conditional

expressions and programming floorplans. The learner will be

able to successfully develop basic ViewBuilder graphics and

provide common editing techniques to existing equipment

and area graphics.

To take the class virtually, you must have ViewBuilder v6.0

installed on your computer.

COURSE ID

VB-200

FORMAT/LENGTH

Classroom/2 Days 1-on-1/2 Days

On-site/2 Days

CEUs

1.6

PREREQ

N/A

Third Party Integration BACnet

BACnet protocol has become the standard protocol within

the Building Management Industry. Today, you will be

hard pressed to not find BACnet in Building Automated

System. In this course a learner will not only learn how

to seamlessly integrate third-party BACnet controls into

a WebCTRL system, but also understand the theory

behind the BACnet protocol. Learners will utilize EIKON,

Networking, and ViewBuilder skills to read and write

BACnet objects while following a sequence of operation to

incorporate them into a WebCTRL system without stressing

the network. A successful integration is never complete

without commissioning the programming, graphic, and

network; Automated Logic Technicians and Engineers will

be equipped with tips and tricks to streamline integrating

to multiple pieces of equipment and fine tune their BACnet

integration to achieve a healthy WebCTRL system, all with

emphasis on efficiency.

COURSE ID

BAC-300

FORMAT/LENGTH

Classroom/1 Day

CEUs

.8

PREREQ

NET-200 VB-200 EIK-200

Third Party Integration Modbus

Modbus protocol has been the protocol of industrial

environment. Today, Modbus can be found in many

industrial controls from energy metering to variable

frequency drives. In this course a learner will not only

seamlessly integrate third-party Modbus controls into a

WebCTRL system, but also understand the theory behind the

Modbus protocol. Learners will utilize EIKON, Networking,

and ViewBuilder skills to read and write from/to Modbus

registers while following a sequence of operation to

incorporate them into a WebCTRL system without stressing

the network. A successful integration is never complete

without commissioning the programming, graphic, and

network; Automated Logic Technicians and Engineers will

be equipped with tips and tricks to streamline integrating to

multiple pieces of equipment and fine tune their Modbus

integration to achieve a healthy WebCTRL system, all with

emphasis on efficiency.

COURSE ID

MOD-300

FORMAT/LENGTH

Classroom/1 Day

CEUs

.8

PREREQ

NET-200 VB-200 EIK-200

ViewBuilder - Intermediate

This course allows learners to create equipment graphics

from a schematic drawing and technician pages. As an

example, learners will be tasked to create one graphic

for different types of similar equipment with the idea of

creating a master graphic for all VAVs to shorten engineering

time. In addition, learners will create a standard template

for their company. Upon successful completion of this

course, learners will be able to identify, define, and/or

apply advanced conditional expressions, WebCTRL paths

for system/equipment linking, complete customization of

equipment graphics including HTML control, external links,

document links, email links, and custom images and symbols

for WebCTRL graphics.

COURSE ID

VB-300

FORMAT/LENGTH

Classroom/3 Days 1-on-1/3 Days

CEUs

1.6

PREREQ

VB-200 + 6 months experience

Page 11: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

20 21BAS University Training Catalog 2020 BAS University Training Catalog 2020

Course Listing – Online

Online Courses

Online courses can be taken in one of two

formats: Self-paced or Virtual. See page 13 for a

description of the two formats.

Advanced Reporting

This series of video tutorials covers the Advanced Reporting

feature in WebCTRL using the Report Manager and pre-

configured custom templates to create, edit, copy, and

import Custom Reports for a WebCTRL system. With

Advanced Reporting users can create a “dynamic table” of

live data and/or historical trend calculations to be used in

graphics and tabular reports. Automated Logic technicians

and engineers will discover the limitless possibilities of

presenting data in a WebCTRL System.

Course Listing

Chilled Water Supply Optimization Solutions

The Chilled Water System Optimizer provides precise

chilled water and condenser water setpoint optimization,

carefully balancing the energy use of the chilled water

plant equipment with the energy use of the chilled water

consumers, which results in an overall reduction in energy

usage and electrical demand. This series of video tutorials

will delve into the complete installation and configuration of

this patent pending control logic that automatically adapts

to the conditions of the Chilled Water System alone, the

Condenser Water System alone, or both Systems in unison.

WebCTRL - Basic

This course is a great place to start your WebCTRL journey!

If you have little or no experience with the Automated Logic

WebCTRL system or you’ve never attended a BASU course,

this course is for you. From this course, you will be able to

work with the WebCTRL user interface, create operators

and privileges, develop schedules, troubleshoot with alarms

and trends, and document with WebCTRL’s report features.

Higher end topics are also included.

COURSE ID

WC-200

FORMAT/LENGTH

Classroom/2 Days Self-paced/1 Day (.8 CEU)

1-on-1/2 Days (.2 CEU)

CEUs

1.6

PREREQ

N/A

WebCTRL - Intermediate

This course covers more advanced features and scenarios

associated with the WebCTRL product. Troubleshooting is

heavily covered in this course with an emphasis on reading

logic pages and using Automated Logic-supported add-on

features to enhance the users’ experience. Upon successful

completion of this course, the learner will be able to

configure and deploy complex options, such as advanced

alarming, creating custom trends, location dependent

security privileges, and setting up operators and privileges

with groups.

COURSE ID

WC-300

FORMAT/LENGTH

Classroom/3 Days

CEUs

2.4

PREREQ

WC-200 + 6 months experience

COURSE ID

AVR-100

FORMAT/LENGTH

Self-paced/1 Hour

CEUs

.1

PREREQ

N/A

COURSE ID

OPT-200

FORMAT/LENGTH

Self-paced/1 Hour

CEUs

.1

PREREQ

N/A

EnergyReports Data Connector

This series of video tutorials covers the EnergyReports

Data Connector product line and its properties from

definition to configuration. Automated Logic technicians

and Engineers will be provided a virtual experience of

installing and configuring the ER Data Connector Add-

on. Once the Add-on is connected, the learner will have

an opportunity to witness defining buildings, configuring

meter sources, and pairing the meter sources to the online

EnergyReports dashboard.

COURSE ID

ERD-200

FORMAT/LENGTH

Self-paced/60 Minutes

CEUs

.1

PREREQ

N/A

Page 12: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

22 23BAS University Training Catalog 2020 BAS University Training Catalog 2020

Course Listing – OnlineCourse Listing – Online

Equipment Touch App

This series of video tutorials will cover the Equipment Touch

App product line and its tools from definition, to installation,

and finally configuration. Automated Logic Technicians and

Engineers will discover the newest options in ViewBuilder

to create Custom Touchscreens while recognizing the

advantages of using the Equipment Touch App over the

original Equipment Touch.

ViewBuilder - Basic

This course introduces Automated Logic-supplied area and

equipment graphics. A complete ViewBuilder overview is

covered, as well as its tools, controls, images, and available

symbols. Custom topics include the use of conditional

expressions and programming floorplans. The learner will be

able to successfully develop basic ViewBuilder graphics and

provide common editing techniques to existing equipment

and area graphics.

To take the class virtually, you must have ViewBuilder v6.0

installed on your computer.

WebCTRL - Basic

This course is a great place to start your WebCTRL journey!

If you have little or no experience with the Automated Logic

WebCTRL system or you’ve never attended a BASU course,

this course is for you. From this course, you will be able to

work with the WebCTRL user interface, create operators

and privileges, develop schedules, troubleshoot with alarms

and trends, and document with WebCTRL’s report features.

Higher end topics are also included.

WebCTRL Simulator Sales Tutorials

Created especially for field office sales personnel, the

Sales Simulator video tutorial series will prepare sales

professionals to conduct a demo using the Sales Simulator

software. The focus of this training, approximately one hour

and a half in length, is how to effectively conduct a WebCTRL

demo using the WebCTRL Simulator. Course restricted to

Automated Logic field office personnel; approval by BAS

University required.

COURSE ID

EDS-300

FORMAT/LENGTH

Classroom/2 Days Virtual/Up to 10 Days

CEUs

1.6

PREREQ

Microsoft Visio Proficiency

Engineering Design Suite (EDS)

The Microsoft Visio® EDS add-on is a tool that allows you

to streamline engineering tasks and the submittal process

to make drawings for installing and commissioning, create

project reports, and control your revisions. The add-on

includes built-in components with data sheets, engineering

calculators and conversions, Cv calculations for water and

steam, a building riser manager, a valve schedule creator,

and a searchable library in which you can add items.

Data can be output to Microsoft Excel® in standalone

spreadsheets or embedded in the Visio® EDS drawings. It

provides automated creation of sequence of operation and

your final drawing package.

COURSE ID

EIK-200

FORMAT/LENGTH

Classroom/2 Days Virtual/Up to 10 Days

CEUs

1.6

PREREQ

N/A

COURSE ID

VB-200

FORMAT/LENGTH

Classroom/2 Days 1-on-1/Varies

On-site/2 Days

CEUs

1.6

PREREQ

N/A

COURSE ID

WC-200

FORMAT/LENGTH

Classroom/2 Days On-site/1 Day (.8 CEU) Self-paced/2 Hours

1-on-1/Varies

CEUs

1.6

PREREQ

N/A

EIKON - Basic

Learn the basics of EIKON programming. Learners who

successfully complete this course will be able to identify

the different types of microblocks, read a sequence of

operations and translate to a program, simulate a program

to find errors, and define microblock properties.

To take the class virtually, you must have EIKON v6.0

installed on your computer.

COURSE ID

ETA-100

FORMAT/LENGTH

Self-paced/60 Minutes

CEUs

.1

PREREQ

N/A COURSE ID

SIM-200

FORMAT/LENGTH

Self-paced/1.5 Days

CEUs

1.2

PREREQ

N/A

Page 13: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

24 25BAS University Training Catalog 2020 BAS University Training Catalog 2020

Course Listing – Online

What’s New!

Are you current with the latest features? Automated Logic

technicians and engineers that want to stay on top of the

enhancements to the complete WebCTRL suite will enjoy

seeing improvements to WebCTRL, Eikon, SiteBuilder,

ViewBuilder, and other tools. Learners should plan to

participate in this course with every new product release.

Typical duration is less than one hour.

COURSE ID

NEW-200

FORMAT/LENGTH

Self-paced/Varies

CEUs

N/A

PREREQ

N/A

Wireless Sensors

In this short video tutorial series, learners will be presented

with the different types of wireless sensors in the WS

product line as well as be shown how to install and configure

a variety of these sensors. Additionally, this course will

review how to create control programs and graphics for

these sensors using EIKON and ViewBuilder respectively.

SensorBuilder® and SensorScan® will also be presented.

COURSE ID

WS-200

FORMAT/LENGTH

Self-paced/1 Hour

CEUs

.1

PREREQ

N/A

Page 14: TRAINING CATALOG - Automated Logic Corporation · 10 BAS University Training Catalog 2020 11 Certification Tracks Design Engineer The Design Engineer certification track is for Automated

26 BAS University Training Catalog 2020Automated Logic Headquarters1150 Roberts Boulevard, Kennesaw, GA 30144770-429-3000 FAX 770-429-3001© Automated Logic 2020

www.automatedlogic.com

BAS University Training Center1975 Vaughn Road, Kennesaw, GA 30144770-429-3000 FAX 770-429-3001© Automated Logic 2020