tr16 manual

MANUAL

A.E.G.Automatic Electric Gun

TR4 / TR15 / TR16MANUAL


TR4 / TR15 / TR16Tel : +1-626-581-0101 Fax : +1-626-581-10111122 Coiner Court City of Industry, CA91748 (U.S.A.)[email protected]

Los AngelesU.S.A.

TAIWANTel : +886-4-798-9000 Fax : +886-4-798-9900No.999, Zhonghua Rd. Shengang Township, Changhua County 50952, Taiwan (R.O.C.)

Tel : +886-2-2692-2000 Fax : +886-2-2692-400011F-3., No.27, Lane 169, Kangning St. Shijr City, Taipei County 22180, Taiwan (R.O.C.)

[email protected], [email protected]@[email protected]

Taipei

Sales Dept.Technology Dept.

PR Dept.

ChangHua(Head Quarter)

MANUAL


TR4 / TR15 / TR16MANUAL


TR4 / TR15 / TR16

G2-201211-02-英

TR4 / TR15 / TR16A.E.G. Manual

1 2

Warning Warning

WarningFor more product information

please visit our websitewww.guay2.com

All products employ a high precision 6.04mm barrel. Using 5.95mm BB pellets is highly recommended. Damage to the product due to by faulty BB pellets voids the warranty. Use with caution.The buyer and the user of this product shall adhere to all local laws regulating the usage and the ownership of airsoft guns.

This product is intended for users 18 years or older.Read all instructions before using this product.Adult supervision required.Always wear safety goggles when using this product.Misuse or careless handling of this product may cause injury.May be hazardous up to 50 meters.

Orange tip disclaimer：All G&G Airsoft guns come with a permanent fixed orange tip required by law, which will grant Airsoft legal usage in the United States.If you alter, modify, abuse or remove the orange tip, all warranty coverage will be void.

You may be liable for damaging public, personal property, or for injuring a person or an animal. Always observe good manners and enjoy fun sport shooting.

When you carry the air gun, attach the safety cap, set the selector lever to the safety position, and always put the air gun in a case or bag.

Never direct the muzzle towards a person, animal, or in any direction that may cause harm or damage to a third party.

Make sure to put the barrel and safety cap onto the muzzle except when shooting, to prevent any accidents, discharge of BB's, and also for dust protection purposes. Never pull the trigger while the barrel and safety cap are attached.

Select a safe place for operating the air gun and avoid places where people and cars are around.

Safety procedures:1. Attach the safety cap to the muzzle.2. Set the selector lever to the safety position.3. Remove the magazine.

Looking into the muzzle is extremely dangerous, regardless of having BB's loaded or not. If you get hit in the eye by a BB pellet, worst case scenario, you may lose your eye sight.

Act ivat ing the t r igger carelessly is extremely dangerous. Never put your finger on the trigger unless the safety cap is removed and you are ready to shoot a target.

When shooting the air guns for target practice or in a game situation, you and all participants must wear safety goggles or other eye protective gear. Please pay attention to ricochets and third parties around you.

Always attach the safety cap to the muzzle, remove the battery and store the air gun in a case or bag and at a place that is out of reach of children.

There may be cases where some BB’s remain in the gun after the magazine has been removed. After removal of the magazine, direct the muzzle towards a safe direction and pull the trigger to confirm that there are no BB's remaining in the gun, then attach the safety cap.

Disassembling or modifying the gun may adversely affect the performance and make it dangerous. It would also void all warranty.


Contents TR4 Series List

3 4

Contents TR4 Series List

01030405061113181921222526273132333435363738394142

Warning

Contents

TR4 Series List

TR15 Series List

TR16 Series List

Blow Back Pneumatic System

TR16 Series Components



Selector & Safety

Installing the Battery

Sight Adjustment

Charging Handle & Hop-up Adjustment

Movable Parts

Magazine Setting

Firing

Maintenance

Troubleshooting & Disclaimer

Parts List - Common

Parts List - Gear Box

Parts List - Mock Suppressor & Barrel

Parts List - Upper Receiver & Sight

Parts List - Handguard & Rail

Parts List - Stock

Parts List - Grip & Others

[ TR4-18 Light DST ]

[ TR4-18 Light ]

[ TR4-18 DST ]

[ TR4-18 ]

[ TR4 CQB-H ]

[ TR4 CQB-R ]

[ TR4 CQB-S ]

[ TR4 CQB-H DST ]

[ TR4 CQB-R DST ]

[ TR4 CQB-S DST ]

For more product information please visit our websitewww.guay2.com

TR4 Series list


TR15 Series List TR16 Series List

5 6

[ TR15 Raider ]

[ TR15 Raider-L ]


TR15 Series list

[ TR15 Raider-XL ]

[ TR15 Raider DST ]

[ TR15 Raider-L DST ]

[ TR15 Raider-XL DST ]


TR16 Series list

[ TR16 Carbine ]

[ TR16 Ranger ]

[ TR16 Carbine Light ]

[ TR16 Carbine DST ]

[ TR16 Ranger DST ]

[ TR16 Carbine Light DST ]



7 8


TR16 Series listFor more product information please visit our websitewww.guay2.com

TR16 Series list

[ TR16 CRW ] [ TR16 CRW Cannon DST ]

[ TR16 CRW Cannon ]

[ TR16 CRW Viper DST ]

[ TR16 CRW DST ]

[ TR16 CRW Viper ]

[ TR16 CQW ]

[ TR16 A2 DST ]

[ TR16 A2 ]

[ TR16 A2 Carbine DST ]

[ TR16 CQW DST ]

[ TR16 A2 Carbine ]



9 10


TR16 Series listFor more product information please visit our websitewww.guay2.com

TR16 Series list

[ TR16 R4 Carbine ] [ TR16 R4 DST ]

[ TR16 R4 ]

[ TR16 R4 Commando DST ]

[ TR16 R4 Carbine DST ]

[ TR16 R4 Commando ]

[ TR16 A3 Carbine ][ TR16 R5 DST ]

[ TR16 R5 ]

[ TR16 A3 DST ]

[ TR16 A3 Carbine DST ]

[ TR16 A3 ]


Blow Back System Patents

1 1 12

Blow Back Pneumatic System


G&G awarded New blow back pneumatic system patents all over the world

True to the faith of mimicking real life firearms, G&G is proud to present its new Pneumatic Blow Back system to its line of airsoft guns. Conventional airsoft blow back utilizes tow hook springs to mimic real life bolt actions, which often lead to excess wear, tear, and poor reliability in the gear box. To alleviate the problem of conventional systems, G&G has independently developed the Pneumatic Blow Back system; a piston driven and gas operated mechanism to better mimic real life bolt actions.This new technology utilizes compressed air to move the bolt, which enables the action without adding extra stress to the gear box.This class leading system represents a significant milestone in the airsoft industry.


TR16 Series Components TR16 Series Components

13 14

Flash Suppressor

Delta Ring

450 Rounds Magazine

Trigger guard

GripSelector lever

Outer BarrelTR16 Carbine / R4 / R4 Carbine

Outer BarrelTR16 A2 / A3 / R5 / A2 Carbine / A3 Carbine

Handguard (Short)TR16 Carbine / A2 Carbine / A3 Carbine

Handguard (Long)TR16 A2 / A3

Receiver SetTR16 A2 / A2 Carbine

Tactical Sling AttachmentTR16 Carbine / A2 Carbine / R4 Carbine

6-Position Retractable StockTR16 Carbine / A2 Carbine / R4 Carbine

Fixed StockTR16 A2 / A3 /A3 Carbine / R4 / R5

Flash SuppressorDelta Ring

450 Rounds MagazineTrigger Guard

Grip

Selector Lever

Outer BarrelTR16 Carbine Light

Outer BarrelTR16 Ranger

Tactical Sling AttachmentTR16 Carbine / A2 Carbine / R4 Carbine

6-Position Retractable StockTR16 Carbine / A2 Carbine / R4 Carbine

Handguard (Short)TR16 Carbine Light / TR16 Ranger

Detachable Carrying HandleTR16 Carbine Light / TR16 Ranger / A3 / A3 Carbine

TR16 Series ComponentsFor more product information please visit our websitewww.guay2.com




1 5 16

TR16 CQW

Trigger

Patriot battery stock for TR16

Tactical gripfor TR16

Ready MagazineTR16 R4 carbine / CRW

Handguard panels

Flash suppressor for SCAR-Type IIPBS mock suppressor for AK

Front sight for TR16 C.Q.W. Rear sight for T418

Front sight for T418

Front sight for T418

Front kit for TR16 CRW Viper

450 rounds magazine

450 rounds magazine

Trigger guard

Trigger guardTactical grip for TR16 series

Selector lever

Selector lever

Rail system (short)TR16 CQW / CRW / Cannon / Viper

Rail system (short)TR16 CQW / CRW / Cannon / Viper

Detachable rear sight

Trigger

Q.D. Sling swivel

Extend battery stock for TR16

Reinforced grip for LR300

TR16 CRW

TR16 CRW Cannon

TR16 CRW Viper

TR16 Series ComponentsFor more product information please visit our website

www.guay2.com

TR16 Series ComponentsFor more product information




1817

Rear sling swivel

Trigger

Magazine catch button

Forward grip

Rail system (short)TR16 R4 / R4 carbine

Outer BarrelTR15 Raider-L / XL

Rail system (short)TR15 Raider / Raider-L

GripTR15 Raider / Raider-L

Rail system (long)TR15 Raider-XL

GripTR15 Raider-XL

Rail system (long)TR16 R5

Front sling swivel

Front sight

Front sight

Ready-MAGTR16 R4 carbine / CRW

Detachable rear sightTR16 R4 / R4 carbine / R5

TR16 R4 / R4 carbine / R5

Handguard panelsTR16 R4 / R4 carbine / R5


TR15 Series ComponentsFor more product information please visit our website

www.guay2.com

Selector lever

Trigger guard450 rounds magazine

Extend battery stock

Front sling swivel

Mock flash suppressorDetachable rear sight



19 20

TR4 CQB H TR4-18

TR4 CQB R TR4 CQB S

LR300 Type flash suppressor

Detachable rear sight

Front sight

Outer barrel

Front gripFront grip

Selector lever

Grip

Trigger guard450 rounds magazine

Assault typeflash suppressor

Handguard panel

Handguard

Sopmod tactical stock

Stock release lever

Trigger

Rear sling swivelRail mount system (SD type)

Stock release lever Rail System

Mock sound suppressor

Q.D. Sling swivel mount

Extend battery stock for TR16

TR4 Series Components TR4 Series ComponentsFor more product information


GripTR4-18 Series

Rear SightTR4-18 Series

Folding Front sightTR4-18 Series

TR4-18 Series


Selector & Safety Installing the Battery

2221

Lower the stock plate nail and open the cover. Close the battery cover.

Click

TR16 A2 / A3 / A3 Carbine / R4 / R5For Fixed Stock Version

Always set the safety mode setting immediately after firing.

► Never operate the selector switch while pulling the trigger. Otherwise, malfunctions may occur.► Pulling the trigger with the Selector being set at safe mode may damage the air gun.

Warning

► Use only the G&G battery purchased from your local dealer.

Warning

Automatic firing

Fully Automatic Mode

The gun will fire continuously while the trigger remains pulled.

Single shot

Semi Mode

The gun will fire one shot each time when pulling the trigger.

The trigger cannot be pulled

Safety Setting Mode

When the gun is in storage or not being fired, always set the selector to the Safe position and attach the protective cap on the muzzle.

Pull the delta ring and hold.Remove the lower handguard.

Hold the battery and pull the delta ring.Remove the lower handguard.

Click

TR16 Carbine / A2 Carbine TR4 CQB HFor Handguard Version

Selector & Safety Installing the Battery

Connect the connector until you hear a 'click', then insert the battery into the fixed stock.

Set the battery beside the outer barrel.Connect the battery plug with the connector until you hear a 'click'.


Installing the Battery Installing the Battery

2423

TR4 CQB R / TR4 CQB STR15 SeriesTR16 CQW

TR4 CQB R / TR4 CQB STR15 Series TR16 R4 Carbine / CRW

TR16 CRW Cannon / CRW Viper

TR16 CQW

1. Push the stock release lever.2. Pull the stock to the last position.

Insert the battery into the stock. Reinstall the stock.

Turn and take off the battery cover.1. Pull and hold the stock release lever mount.2. Pull out the stock.

For Extended Battery Stock Version

Pull out the connector.

Release the battery stock.

Insert into upper receiver and connect firmlyuntil you hear a 'click'.

1. Insert the battery into the stock.2. Lock the stock.

For Ready Magazine Version

For Patriot Battery Stock Version

Installing the Battery Installing the Battery

For Extended Battery Stock Version

Connect the battery plug into the connector until you hear a 'click'.

Connect the battery plug with the connector until you hear a 'click'.

Connect the battery plug with the connector until you hear a 'click'.

Click

Click

Click Click

2 2

1

2

1

1


Warning


Warning


Sight Adjustment Charging Handle &Hop-up Adjustment

2625

Sight Adjustment Charging Handle & Hop-up Adjustment

Front sight adjustment

Precision targeting Up-down adjustment

Windage adjustment knob

LEFT

LEFTLEFT

RIGHTRIGHTRIGHT

RIGHTRIGHTFor left-right adjustment.Turning clockwise :Shifts the pellet hitting point to the right.Turning counterclockwise :Shifts the pellet hitting point to the left.

Turning the windage adjustment dial will move the pellet hitting point to the left or right.

For front sight up-down adjustment.Turning clockwise : Raises the pellet hitting point.Turning counterclockwise : Lowers the pellet hitting point.

Battle sight ( For common shooting )Used for full automatic firing.

Battle sight ( For special shooting )Used for precision firing. Raises the pellet hitting point.

Turning the dial UPwill raise the pellet hitting point.

Turning the dial DOWNwill lower the pellet hitting point.

UP

DOWN

► Make sure not to lose the adjustment tool.

Warning► Be careful not to catch your fingers in the dummy bolt.

Warning

Warning

Hop-up adjustment

1. The Charging handle can be pulled and the bolt will be fastened.2. Pulling the charging handle will take the bolt back and open the port cover.

Turn the hop-up for a desired flight pattern of the BB pellet.The hop-up dial can be turned to a certain degree.Turning it too much will damage the unit.

Open the port cover

Normal Hop

►Too much hop-up ( Return the lever toward Normal ).

Best Direction.

Not enough hop-up ( Move the lever toward HOP ).or Too much hop-up ( Return the lever toward Normal ).

2

1

Never hold the gun sideways as the BB pellets will curve right or left due to the hop-up system.

This function is only for the plastic/blow back version


Movable Parts Movable Parts

2827

► Only adjust if the gear noise becomes shrilly. Movable Parts Movable PartsWarning

Depress the Trigger Guard

Depress the trigger guard plunger with a proper tool and open the trigger guard.

Motor Adjustment

The motor adjustable screw is at the bottom of the grip.Use a screwdriver to adjust.

Set the forward grip on the rail. Move the forward grip to adjust position. Fasten the knob.

Forward Grip Setting

Fasten the interface knob. Finish.

Installing the Carrying Handle

Put on the detachable rear sight on the upper receiver.

Fasten the interface knob.

Installing the Rear Sight

Finish.

Connect the detachable carrying handle with the upper receiver.



3029


Set the forward grip on the rail. Slide in the rail handguard panels. Finish.

Rail Handguard Panels Setting

Put on Q.D.sling swivel mount on the rail.Fasten the screw.

Install the Q.D.sling swivel on the Q.D.slingswivel mount.

Install the Q.D. sling swivel on the sopmodtactical stock.

Q.D. Sling Swivel Setting

Pull the delta ring. Remove the lower handguard. Remove the upper handguard.

Removing the Handguard

Push the release lever to unlock. Pull the stock. Adjust the position of the stock. (6 positions)

Retractable Stock


Magazine Setting Firing

323 1

Magazine Setting Firing

Firing

Click

Set the Selector Lever to Semi or Full Auto.

Warning ► Make sure to set the magazine upwards. It is securely installed with you hear a 'click'.► Confirm that the safety lever is set to Safety position and do not place your finger on the trigger.

Warning ► Select a safe place for operating the air gun.► Never put your finger on the bolt when operating the air gun.

Press the magazine release. Pull the magazine out of the receiver.

Magazine Setting To Release the Magazine

Open the magazine cover.Load G&G 5.95mm BB pellets into the magazine.The magazine is capable ofholding approximately 450 pellets.

Magazine Setting

ClickCautions On Motor & Battery

After Operation

Charge the battery if the firing cycle becomes slow.Stop using the air gun for 5-10 minutes after firing around 500 rounds in order to ensure a longer life of the motor and battery.

Remove the magazine and fire at a safe direction for 2-3 seconds. Push the forward assist knob to release the spring and have the selector set into safety mode. Make sure that the barrel is empty.

Always disconnect the battery and attach the protective cap whenever you do not operate the air gun.

Press

After the BB pellets have been loaded, close the cover and turn the gear on the bottom until the sound changes.

Insert the magazine into the body until you hear a 'click'.

Make sure to install the magazine upwards and into the body.It is installed properly when you hear a 'click'.

Remove the protective cap only when you are ready to fire the gun.

2.

1.

1.2.


Maintenance Troubleshooting

& Disclaimer

3433

Maintenance Troubleshooting

DisclaimerAll products in this manual are imitation firearms and are not intended nor represented to be comparable in design, appearance, or function to any actural firearm offered by other manufacturers.Product names are trademarks of G&G, which has no affiliation to, and is not associated, or sponsored by any manufacturer of actual or imitation firearms. Products may vary form those pictured.

Accessories pictured are not always included with product.Adult supervision required for users under 18 years of age.The purchaser and user should conform to all laws governing the ownership of airsoft guns.

No operation at all

Although motor is revolving, no pellet can be fired

Impossible full-auto operation(automatic firing)

Shooting distance becomes shorter

Too loud operating noise

Pellets being fallen out from barrel end

If gun gets wet

SYMPTOM POTENTIAL CORRECTIVE

Stop operation immediately, disconnect the battery, wipe off water from inside the main body and the battery. After the gun is completely dry, carry out trial firing. If the unit is not operational, please contact your local dealer for repair.

Selector lever is set to safety.Battery is not charged.Battery connector is disconnected.The and of battery connector is reversed.Expired motor life (50,000 to 60,000 rounds) or poor electrical connection.Pellets are clogged inside the magazine.

Pellets are clogged in the chamber.Faulty gear.Insufficient battery power.Faulty pellet feed of magazine.Poor electrical connection.Damaged or worn chamber set.Damaged or worn piston set (O-ring,piston spring)Something is jammed in the inner barrelFaulty BB pellets (too small or heavy)Shortage of silicone oilGear problem caused by too many blank firingWorn or damaged gearGear problem caused by too many blank firingDamaged or worn chamber set.No hop setting.Faulty BB Pellets (too small or heavy)

Set the selector lever to Semi or Full Auto.Charge the battery.Connect the connector.Switch the batteries to the correct position.Replace the dead motor (can be purchased from local dealer or directly from G&G). Check and repair the contacts.Insert the charging rod into the magazine and move up and down a few times to remove clogged pellets.Remove clogged pellets using the cleaning rod.Purchase the replacement gear from your dealer or G&G and repair.Charge the battery.Repair clogging of the magazine.Consult your dealer or G&G for overhaul maintenance or repair.

Replace the replacement parts (purchase from your dealer or G&G)

Use the cleaning rod and clean the inner barrel.Use the genuine G&G Pellets.Place a few drops of silicone oil onto the upper chamber.

Consult your dealer or G&G for overhaul maintenance, part replacement (gear,etc.) or repair.

Turn the hop adjustment lever toward Hop.Use the G&G Pellets.

1. Place a few drops of silicone oil or teflon oil into the pellet entrance. After inserting BB pellets into the magazine, fire the gun for up to 200~300 pellets.2. To complete the cleaning, use the cleaning rod ( with cotton ) to remove excess oil.

Maintenance When Pellet Speed Becomes Low

Removing Clogged Pellets

Warning

► Do not jam the cleaning rod into the barrel by force.►

► Make sure no dirt gets into the chamber to avoid clogging of pellets.► Hop-up may be unstable for 200 to 300 rounds after using silicone oil. This is the normal operation of the gun.► Never use CRC-556, WD40, or other corrosive lubricants.

Warning

1. Return the hop-up dial to the Normal position and insert the cleaning rod from the lead edge of the barrel.2. To remove clogged BB’s, carefully insert the cleaning rod inside with the flat tip facing down as shown below.

Should the BB’s remains inside the barrel, point the gun towards a safe direction and discharge any loosened BB’s in semi-automatic mode.


Parts List - Common Parts List - Gear Box

3635

TR16 - 01

TR16 - 02

TR16 - 04

TR16 - 03

TR16 - 07 TR16 - 0

8TR16 - 0

9

TR16 - 21

TR16 - 19

TR16 - 18

TR16 - 17

TR16 - 20

TR16 - 10

TR16 - 12

TR16 - 13

TR16 - 14

TR16 - 11

TR16 - 06

TR16 - 05

TR16 - 16

TR16 - 15

Charging Handle

Port Cover Set

Magazine Catch Set

Selector Plate

Assist Knob Set

Selector Lever Set

Bolt Catch Set

Lower Receiver Set

Hop-Up Set

Hop-Up Rubber Set

Piston Rod

Front Frame Lock Pin Set

Trigger Guard Set

Rear Frame Lock Pin Set

Magazine

Motor Set

TR16-01

TR16-02

TR16-03

TR16-04

TR16-05

TR16-06

TR16-07

TR16-08

TR16-09

TR16-10

TR16-11

TR16-12

TR16-13

TR16-14

TR16-15

TR16-16

Common Parts for TR16 / TR15 / TR4

Non-Blowback for TR16 A2 / A2 Carbine

Blowback for TR16 / TR15 / TR4

TR16-17 Gear Box Set

Blowback Gear Box Set

Charging Upper Cover

Charging Plate

Blowback Piston Set

TR16-18

TR16-19

TR16-20

TR16-21

► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com

Common Parts► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com

Gear Box Set

TR4 / TR15 / TR16A.E.G. ManualParts List -

Mock Suppressor & Barrel Parts List -

Upper Receiver & Sight

3837

TR16 - 31

TR16 - 32

TR16 - 33

TR16 - 34

TR16 - 35

TR16 - 36

TR16 - 37

TR16 - 28

TR16 - 25

TR16 - 24

TR16 - 22

TR16 - 38

TR16 - 39

TR16 - 40

TR16 - 41

TR16 - 42

TR16 - 48

TR16 - 43

TR16 - 46

TR16 - 44

TR16 - 45

TR16 - 47

TR16 - 23TR16 - 3

0

TR16 - 26

TR16 - 29

TR16 - 27


Mock Suppressor & Barrel ► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com

Upper Receiver & Sight

Mock Suppressor

Mock Suppressor (CRW / CQW / TR4-18)

Mock Suppressor (TR4-18 Light)

Mock Suppressor (CQB-S)

Mock Suppressor (CQB-R/H)

Mock Suppressor (CRW Cannon)

Mock Suppressor (CRW Viper)

Inner Barrel (Different Lengths)

Outer Barrel (CRW / CQW / CRW Cannon)

Outer Barrel (Carbine Light / CQB-R/H / Raider)

Outer Barrel (Ranger)

Outer Barrel

Outer Barrel (A2 / A3 / R5)

Outer Barrel (A2 Carbine / A3 Carbine)

Outer Barrel (TR4-18 Series)

Outer Barrel Extender (TR4-18)

Front Sight

Front Sight (CRW / Viper / Canoon / TR4-18 Light)

Front Sight (CQW)

Front Sight (TR4-18)

Front Sight Mount (TR4-18 Series)

Detachable Carrying Handle

Upper Receiver (A2 / A2 Carbine)

Upper Receiver

Rear Sight (with TR16-38,39)

Rear Sight

Rear Sight (CRW Viper / Cannon)

TR16-22

TR16-23

TR16-24

TR16-25

TR16-26

TR16-27

TR16-28

TR16-29

TR16-30

TR16-31

TR16-32

TR16-33

TR16-34

TR16-35

TR16-36

TR16-37

TR16-38

TR16-39

TR16-40

TR16-41

TR16-42

TR16-43

TR16-44

TR16-45

TR16-46

TR16-47

TR16-48

TR4 / TR15 / TR16A.E.G. ManualParts List -

Handguard & Rail Parts List -

Handguard & Rail

4039

TR16 - 52

TR16 - 53

TR16 - 51

TR16 - 54

TR16 - 62 TR16 - 5

5

TR16 - 60

TR16 - 59

TR16 - 58

TR16 - 56

TR16 - 57

TR16 - 61

TR16 - 50TR16 - 4

9

Handguard Front Fixed Ring

Handguard Front Fixed Ring(TR16 A2 / A3)

Handguard

Handguard (TR16 A2 / A3)

Rail System Set(TR16 R4 / R4 Carbine /TR4 CQB-R)

Rail System Set (TR16 R5)

Rail System Set (Raider-XL)

Rail System Set

Rail System Set (TR4 CQB-S)

Rail System Set(CQW / CRW / Viper / Cannon)

Rail System Set (TR4-18 Series)

Rail System Rear Fixed Set (with No. TR16-50, 51)

Delta Ring (with No. TR16-52,53)

Delta Ring

TR16-49

TR16-50

TR16-51

TR16-52

TR16-53

TR16-54

TR16-55

TR16-56

TR16-57

TR16-58

TR16-59

TR16-60

TR16-61

TR16-62


Handguard & Rail► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com

Handguard & Rail


Parts List - Stock Parts List - Grip & Others

424 1

TR16 - 72

TR16 - 69

TR16 - 71

TR16 - 67

TR16 - 65

TR16 - 73

TR16 - 75

TR16 - 76

TR16 - 78

TR16 - 74

TR16 - 79

TR16 - 77

TR16 - 64

TR16 - 63

TR16 - 70

TR16 - 66

TR16 - 68

Sling Attachment (CRW Viper / Cannon / Raider / Raider-L/XL)

Sling Attachment

Stock Washer (CRW)

Buffer Tube Set (with No. TR16-64, 65)

Rear Q.D. Sling Swivel Set (CRW)

Patriot Battery Stock Set (CRW Viper / Cannon)

Fixed Stock Set

Retractable Stock Set

Extended Battery Stock Set

Sopmod Tactical Stock Set (CQB-H)

Grip Set (Raider / Raider-L)

Grip Set (CQW)

Grip Set (CRW / Viper / Cannon / Raider-XL / TR4-18)

Grip Set

Ready Magazine Set (CRW / R4 Carbine)

Handguard Panel Set (R5 / CQB-S/R)

Forward Grip (R4 / R4 Carbine / R4 Commando / R5 / CQB-S/R)

TR16-63

TR16-64

TR16-65

TR16-66

TR16-67

TR16-68

TR16-69

TR16-70

TR16-71

TR16-72

TR16-73

TR16-74

TR16-75

TR16-76

TR16-77

TR16-78

TR16-79


Stock► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com

Grip & Others

Loading BB Pellets Movable Parts - Stock Rear Sight Adjustment

Extra Storage Space Front Sight AdjustmentInstalling the BatteryComponents

INSTRUCTIONMANUAL

1. Pull and hold down the delta ring.2. Remove the lower handguard.

TR4 MOD 0

TR4 MOD 0

TR4 MOD 0 DST

Flash Suppressor

Delta Ring

Handguard Picatinny Rail x 3

Mid-Cap 120R MagazineGrip

Selector Lever

Detachable Front Sight Tactical Sling Attachment

6-Position Retractable Stock

Detachable Rear Sight

Click1

1

4

5

1

2

2

3

2

1

2

Connect the battery with the connector until you hear a 'click', then reinstall the lower handguard.

Press the button then pull out.

1.Press down the button to fold the rear sight.2.Loosen the hex screw before removing the rear sight. Pull the charging handle so the rear sight can be removed.

1.Pull the release lever to adjust the position of the stock. (6 positions)2.Pull the locking lever until it click into place to secure the position of the stock.

Turn the knob counterclockwise to remove the front sight.

1. Open the trap door on the top of the BB loader.

2. Load G&G 5.95mm BB pellets into the Magazine style BB Loader.

3.Connect magazine style loader with the 120R Magazine.

4. Slide the retainer to release the injection lever.

5. Press the injection lever to load BBs into the magazine. Continue loading until the magazine is full.

Magazine Style420R BB Loader[ Optional Parts ]Model No. G-08-100-1

LockLock

UnlockUnlock


1

2

12

3

1

2

3

1

22

1 23

45 6

7 8

910

1

12

12

4 5 6

2

1

2

13

5

24

3

1

2

2

1

3

4

5

2

1

1

3

2

3

4

2

1

3

49

5

6

7

8

10

11

12

2

1

23

2

3

1

4

2

3

4

56

1

7

2

345

6

1

23

1389

14

4

56

7

1112 8

1

10

3

4

5

1

2

1

3

2

TR4 MOD0 - 01

TR4 MOD0 - 02

TR4 MOD0 - 26

TR4 MOD0 - 28TR4 MOD0 - 2

9

TR4 MOD0 - 30

TR4 MOD0 - 32

TR4 MOD0 - 31

TR4 MOD0 - 27

TR4 MOD0 - 03

TR4 MOD0 - 04

TR4 MOD0 - 05

TR4 MOD0 - 07

TR4 MOD0 - 35

TR4 MOD0 - 08

TR4 MOD0 - 15

TR4 MOD0 - 33

TR4 MOD0 - 25

TR4 MOD0 - 16

TR4 MOD0 - 18

TR4 MOD0 - 19

TR4 MOD0 - 21

TR4 MOD0 - 22

TR4 MOD0 - 24

TR4 MOD0 - 23

TR4 MOD0 - 20

TR4 MOD0 - 17

TR4 MOD0 - 34

TR4 MOD0 - 10

TR4 MOD0 - 11

TR4 MOD0 - 12

TR4 MOD0 - 13

TR4 MOD0 - 14

TR4 MOD0 - 09

TR4 MOD0 - 06

TR4 MOD0 - 01

TR4 MOD0 - 02

TR4 MOD0 - 03

TR4 MOD0 - 04

TR4 MOD0 - 05

TR4 MOD0 - 06

TR4 MOD0 - 07

TR4 MOD0 - 08

TR4 MOD0 - 09

TR4 MOD0 - 10

TR4 MOD0 - 11

TR4 MOD0 - 12

TR4 MOD0 - 13

TR4 MOD0 - 14

TR4 MOD0 - 15

TR4 MOD0 - 16

TR4 MOD0 - 17

TR4 MOD0 - 18

TR4 MOD0 - 19

TR4 MOD0 - 20

TR4 MOD0 - 21

TR4 MOD0 - 22

TR4 MOD0 - 23

TR4 MOD0 - 24

TR4 MOD0 - 25

TR4 MOD0 - 26

TR4 MOD0 - 27

TR4 MOD0 - 28

TR4 MOD0 - 29

TR4 MOD0 - 30

TR4 MOD0 - 31

TR4 MOD0 - 32

TR4 MOD0 - 33

TR4 MOD0 - 34

TR4 MOD0 - 35

Flash Suppressor

Lower Handguard Set

Upper Handguard Set

Outer Barrel Set

Hop Up Set

Delta Ring

Inner Barrel

Upper Receiver Set

Charging Handle Set

Port Cover Set

Front Frame Lock Pin Set

Bolt Catch Set

Selector Lever Set

Magazine Catch Set

Sling Swivel Mount

Stock Tube

Magazine

Lower Receiver Set

Trigger Guard Set

Selector Plate

Rear Frame Lock Pin Set

Grip Set

Motor

Grip Bottom Set

GOS-V2 Stock Set

Gear Box Set

Detachable Front Sight Set

Blow Back Pneumatic Piston Set

Charging Plate Set

Charging Upper Cover Set

Right Selector Cap

Wire

Rear Sight

Handguard Retainer

Imitation Gas Tube


Parts List

ADDITIONALINSTRUCTIONMANUAL

TR4 MOD 0

G2-201312-03-英

tr16 manual

Documents