toyota vehicle security system7446b8f8-1ceb-49b7...tvss v toyota vehicle security system...
TRANSCRIPT
TVSS VTOYOTA VEHICLE SECURITY SYSTEM
INSTALLATION INSTRUCTIONS
Corolla
RHD
PART NUMBER
FOR **E12-A*R
Manual Ref. Nr. T5RE12A/J-0-400
MAIN KIT 08585-12990
FITTING KIT (For manual air conditioner) 08586-1E870
FITTING KIT (For auto air conditioner) 08586-1E860
SUBKIT (SIREN AND RADAR KIT) 08586-1E850
• Be sure to disconnect the negative (-)lead from the battery terminals.
• Do not pinch the rear wiring or harnessin the tightened part.
• When passing the wires through thebulkhead or other panels, use a grommet to ensure waterproofing.
• Protect the wiring with tape when it ispassed through a hole.
• When disconnecting the connectors,be sure to grip the connector body. Donot tug on the wiring.
• Do not forcibly pull any car wiring har-ness. Rough tugging may result in ope-ned connections, or a broken wire orharness.
• Confirm that lamps, horn, wiper and oth-er car accessories operate normally.
• Protect your car with wing covers, seatand so on.
• Use the correct tool when tighteningbolts or nuts.
• Before drilling a hole, check that the rearof the mounting wall is clear.
• Be sure to firmly tighten connectors andterminals.
• Before connecting the power wiring tothe battery, check the wiring con-nections, harness, etc. to see that theyare properly secured.
• Check body and trim near area of installation to be certain nodirt or scratches resulted from the installation.
Corolla (RHD) - 204-02
Corolla (E12-A) TVSS V
waterproof - O.K. !!
Grommet
Stop it !
Taping
Insert completely
PLEASE READ THOROUGHLY THESE PRECAUTIONS BEFORE THE TVSS INSTALLATION
PRECAUTIONS
Precautions .................................................................................................................................................................................... 2
System Components• Fitting Kit ............................................................................................................................................................................. 4• Main Kit ............................................................................................................................................................................... 6• Radar Sensor Kit ................................................................................................................................................. 6• Siren Kit ............................................................................................................................................................................... 6
System Layout and Wire Harness Outline (Main)• For Manual Air Conditioner ................................................................................................................................. 7• For Auto Air Conditioner ..................................................................................................................................... 8
System Layout and Wire Harness Outline (Engine) ........................................................................................ 9
Connector Arrangement of the TVSS Fitting Kit (Pin View)• For Manual Air Conditioner ................................................................................................................................. 10• For Auto Air Conditioner ..................................................................................................................................... 11
TVSS Installation Instructions• Vehicle Disassembly ........................................................................................................................................... 12• Wire Harness Installation (For Manual Air Conditioner) .................................................................................... 20• Wire Harness Installation (For Auto Air Conditioner) ........................................................................................ 28• Mounting the Radar Sensor ................................................................................................................................ 32• Mounting the TVSS ECU ..................................................................................................................................... 37• Mounting the Siren ............................................................................................................................................. 39• Mounting the Hood Switch ................................................................................................................................. 40• Connection of the Connector .............................................................................................................................. 41• Attaching the Stickers ......................................................................................................................................... 42
Corolla (RHD) - 3
Corolla (E12-A) TVSS V
04-02
TABLE OF CONTENTS
Corolla (RHD) - 4
Corolla (E12-A) TVSS V
04-02
No. Description Qty Qty
TVSS WIRE HARNESS 1 1 1
TVSS WIRE HARNESS 2 1 -
TVSS ECU BRACKET 1 1
RADAR SENSOR BRACKET 1 1
HOOD SWITCH 1 1
HOOD SWITCH BRACKET 1 1
SIREN BRACKET 1 1
BOLT (M6x18: FOR HOOD SWITCH) 1 1
SCREW (M6x16: FOR TVSS ECU) 1 1
NUT (M6) 2 2
SCREW (M4x10: FOR RADAR SENSOR) 2 2
NUT (M4: FOR RADAR SENSOR) 2 2
FOAM TAPE (1 DIVISION ON 1 SHEET) 1 1
FOAM TAPE (2 DIVISIONS ON 1 SHEET) 1 1
WIRE TIE (200mm) 5 10
WIRE TIE (150mm) 10 25
WINDOW STICKER 2 217
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
FOR MANUAL AIR CONDITIONER (08586-1E870)
FOR AUTO AIR CONDITIONER (08586-1E860)
FITTING KIT 08586-1E870 / 08586-1E860
Corolla (RHD) - 5
Corolla (E12-A) TVSS V
04-02
5 7
21
6
3 4
8
9 1110 12
13 1514 16
ATT
OOY
17
Corolla (RHD) - 6
Corolla (E12-A) TVSS V
04-02
I
MAIN KIT 08585-12990
No. Description Qty
TVSS ECU 1I
II III IV
RADAR SENSOR KIT 08586-1E850
No. Description Qty
RADAR SENSOR 1
ALUMINIUM TAPE 1
TEMPLATE 1IV
III
II
i ii iii
SIREN KIT 08586-1E850
No. Description Qty
SIREN 1
BOLT 2
NUT 2iii
ii
i
Corolla (RHD) - 7
Corolla (E12-A) TVSS V
04-02
SYSTEM LAYOUT AND WIRE HARNESS OUTLINE (MAIN)
G
C
d
D
E
e
F
J
A
B
H
III
Driver’s kick panel connector (12P female and male blue)
Pre-wired connector (10P male white)
Turn signal flasher relay connector (8P female and male black)
TVSS ECU connector (40P female white)
Key unlock warning connector (2P female and male black)
Horn connector (6P female white and male blue)
Radar sensor connector (4P female white)
Passenger's side J/B connector (6P female and male white)
Passenger's kick panel side connector (10P female and male white)
Optional wire for add on (in) (yellow) (Not used)
Optional wire for add on (in) (yellow) (Not used)
TVSS ECU
Radar sensorII
I
e
d
J
H
G
F
E
D
C
B
A
FOR MANUAL AIR CONDITIONER
Corolla (RHD) - 8
Corolla (E12-A) TVSS V
04-02
SYSTEM LAYOUT AND WIRE HARNESS OUTLINE (MAIN)
F
C
D
B
dE
e
A
G
III
Driver’s kick panel side connector (12P female and male blue)
Manual lock switch terminal wire (blue/white)
Manual unlock switch terminal wire (blue/yellow)
Optional terminal for add on (in) (yellow) (Not used)
Optional terminal for add on (out) (green) (Not used)
Radar sensor connector (4P female white)
Passenger's side J/B connector (4P female and male white)
Optional wire for add on (in) (yellow) (Not used)
Optional wire for add on (out) (green) (Not used)
TVSS ECU
Radar sensorII
I
e
d
G
F
E
D
C
B
A
FOR AUTO AIR CONDITIONER
Corolla (RHD) - 9
Corolla (E12-A) TVSS V
04-02
SYSTEM LAYOUT AND WIRE HARNESS OUTLINE (ENGINE)
Hood switch
Sireni
1
FOR ALL MODELS
5DOOR MODELS 3DOOR MODELS
1
i i
Corolla (RHD) - 10
Corolla (E12-A) TVSS V
04-02
CONNECTOR ARRANGEMENT OF THE TVSS (PIN VIEW)
(female) (male)
(female) (male)
(female) (male)
(female) (male)
(female) (male) (female) (male)
(female)
2
23 24 25 26 27 28 29 3634 37 40
3 5 8 9 10 11 12 16 17 206 7
21
(female)
(male)
FOR MANUAL AIR CONDITIONER
A
C
E
G H
J
D
F
B
Corolla (RHD) - 11
Corolla (E12-A) TVSS V
04-02
CONNECTOR ARRANGEMENT OF THE TVSS (PIN VIEW)
FOR AUTO AIR CONDITIONER
(female) (male)
(female)
(female) (male)
(female terminal)
(female terminal) (female terminal)
(female terminal)
A
C D
E F
G
B
Corolla (RHD) - 1204-02
Corolla (E12-A) TVSS V
Figure 1
Figure 2
Figure 3
VEHICLE DISASSEMBLEY
2.
Remove the passenger's side kick panel .: Retainer (1x)100
2
1.
Remove the passenger's side front doorscuff plate .
: Clip (6x)1
3.
Remove the glove compartment .: Clip (4x)
: Screw (1x)101
3
1
3
100
101
VEHICLE DISASSEMBLEY
FOR MANUAL A/C MODELS
FOR MANUAL A/C MODELS
2
5.
a) Remove the gear shift knob .b) Remove the gear shift cover .
: Clip (6x)6
5
4.
Remove the register .: Clip (2x)
4
Corolla (RHD) - 13
Corolla (E12-A) TVSS V
04-02
Figure 6
FOR MANUAL A/C MODELS
6.
Remove the gear shift cover .: Clip (6x)
7
Figure 4
Figure 5
4
FOR MANUAL TRANSMISSION
FOR MANUAL A/C MODELS
FOR AUTOMATIC TRANSMISSION
6
7
5
Corolla (RHD) - 14
Corolla (E12-A) TVSS V
04-02
7.
a) Remove the knob from the centrecluster panel.
b) Remove the centre cluster panel .: Clip (4x)
: Screw (1x) 102
9
8
8.
Remove the audio unit .: Clip (4x)
: Screw (4x)103
10
9.
Remove the driver’s side front door scuffplate .
: Clip (7x)1
Figure 7
Figure 8
Figure 9
103
FOR MANUAL A/C MODELS
FOR MANUAL A/C MODELS
FOR 5DOOR MODELS
9
8
1
102
10
Corolla (RHD) - 15
Corolla (E12-A) TVSS V
04-02
Figure 12
Figure 10
Figure 11
10.
Remove the driver’s side front door scuffplate .
: Clip (6x)1
11.
Remove the driver’s side kick panel .: Retainer (1x)100
2
12.
a) Remove the cluster panel from thedriver’s side lower dash panel.
: Clip (4x)b) Remove the small compartment
from the driver’s side lower dash panel.: Clip (4x)
15
9
FOR 3DOOR MODELS
1002
9
15
1
Corolla (RHD) - 1604-02
Corolla (E12-A) TVSS V
13.
a) Turn the steering wheel to the left,then remove the screw .
b) Turn the steering wheel to the right,then remove the screw .105
1610516
14.
Remove the driver’s side under cover .: Screw (2x)105
17
15.a) Remove the knob from the tilt lever.
: Screw (2x)b) Remove the steering column under
cover .: Screw (1x)
c) Open the finish panel from the lo-wer dash panel.
: Clip (4x)
19106
18
10620
Figure 13
Figure 14
Figure 15
105
105
106
10516
17
2018
19
FOR MANUAL AIR CONDITIONER
FOR MANUAL AIR CONDITIONER
Corolla (RHD) - 17
Corolla (E12-A) TVSS V
04-02
16.
Remove the finish panel from the lowerdash panel.
: Screw (2x)105
19
17.
Remove the driver’s side rear door scuff plate.: Clip (3x)
1
18.
Lift and remove the driver’s side rear seatcushion .22
Figure 16
Figure 17
Figure 18
1
22
FOR MANUAL AIR CONDITIONER
FOR 5DOOR MODELS
19105
Corolla (RHD) - 18
Corolla (E12-A) TVSS V
04-02
19.
Remove the rear seat back .: Bolt (2x)106
23
20.
a) Peel the weather strip .b) Remove the driver’s side quarter trim
.: Bolt (2x): Clip (1x)
: Clip (8x)108107
26
25
21.
a) Remove the parcel shelf .b) Remove the luggage compartment
spare wheel mat .28
27
Figure 19
Figure 20
Figure 21
106
107
108
24
23
26
27
28
25
Do not remove the seat belt anchor .24
NOTE:
FOR 3DOOR MODELS
Corolla (RHD) - 19
Corolla (E12-A) TVSS V
04-02
22.
a) Remove the luggage compartmentspare wheel cover .
b) Remove the luggage compartmentspare wheel cover .
: Bolt (2x)10930
29
23.
a) Remove the cover (2x) from the lug-gage finish plate .
: Bolt (2x)b) Remove the luggage finish plate .
: Clip (6x)11032
11032
31
24.
Remove the driver’s side luggage side co-ver .
: Bolt (1x): Clip (1x)
: Clip (4x)112111
33
Figure 22
Figure 23
Figure 24
When the size of the tire is 195, the lug-gage compartment spare wheel cover
is not installed.29
NOTE:
109
110
110
111
112
29
30
31
31
32
33
Corolla (RHD) - 2004-02
Corolla (E12-A) TVSS V
2.
a) Connect the 8P female connector (black) of the TVSS wire harness tothe flasher relay .
b) Connect the 8P male connector (black) of the TVSS wire harness tothe vehicle harness 8P connector(black).
411
C
401
C
1.
a) Locate and disconnect the flasherrelay .
b) Disconnect the 8P connector (black)from the flasher relay .40
4140
Figure 25
Figure 26
3.
Refit the flasher relay .40
Figure 27
WIRE HARNESS INSTALLATION (FOR MANUAL AIR CONDITIONER)
40
40
40
41
41
c
B
c
1
1
Corolla (RHD) - 21
Corolla (E12-A) TVSS V
04-02
4.
Locate and disconnect the 12P connector(blue) in the driver’s side kick panel
area.42
5.
a) Connect the 12P female connector (blue) of the TVSS wire harness tothe driver’s side connector block.
b) Connect the 12P male connector (blue) of the TVSS wire harness tothe vehicle harness 12P connector (blue).
421
A
1
A
6.
Attach the TVSS wire harness to thevehicle harness using the wire ties (4x).16
1
Figure 28
Figure 29
Figure 30
42
42
A
A
1
1
16
16
Corolla (RHD) - 22
Corolla (E12-A) TVSS V
04-02
Figure 33
7.
Locate the 10P connector (white), thenremove the tape from the 10P connector .43
43
8.
a) Connect the 10P male connector (white) of the TVSS wire harness tothe vehicle harness 10P connector (white).
b) Attach the 10P connector to the vehi-cle harness using the foam tape (1x).
c) Attach the TVSS wire harness tothe vehicle harness using the wire tie
(1x).16
1
14
431
B
9.
Locate and disconnect the 6P connector (white) in the steering column area.
44
Figure 31
Figure 32
43
43
44
B
B
1
1
14
16
Corolla (RHD) - 23
Corolla (E12-A) TVSS V
04-02
10.
Locate and disconnect the 2P connector (black) in the key cylinder area.
45
11.
a) Connect the 6P female connector (white) of the TVSS wire harness tothe steering area.
b) Connect the 6P male connector (blue) of the TVSS wire harness tothe vehicle harness 6P connector (white).
c) Connect the 2P female connector (black) of the TVSS wire harness tothe key cylinder area.
d) Connect the 2P male connector (black) of the TVSS wire harness tothe vehicle harness 2P connector (black).
451
E
1
E
441
F
1
F
12.
a) Secure the 6P connectors to the vehi-cle harness using a wire tie (1x).
b) Attach the TVSS wire harness tothe vehicle harness using wire ties (2x).
16
1
16
Figure 34
Figure 35
Figure 36
45
4445
F F
FF
E
1
116
16
Corolla (RHD) - 24
Corolla (E12-A) TVSS V
04-02
13.
Route and attach the TVSS wire harnessand 2P connectors to the vehicle har-
ness using wire ties (5x).16
1
14.
Route and attach the TVSS wire harnessto the vehicle harness using wire ties
(3x) in the centre console area.151
15.
Route the TVSS wire harness throughthe upper part of the vehicle side stay .46
1
Figure 37
Figure 38
Figure 39
E
E
16
16
15
16
1
1
1
BOTTOM SIDE VIEW
47
47
Corolla (RHD) - 25
Corolla (E12-A) TVSS V
04-02
16.
Locate and disconnect the 6P connector (white) from the passenger’s side J/B .47
48
17.
a) Connect the 6P female connector (white) of the TVSS wire harness tothe passenger’s side J/B .
b) Connect the 6P male connector (white) of the TVSS wire harness tothe vehicle harness 6P connector (white).
481
H
471
H
18.
a) Attach the TVSS wire harness tothe vehicle harness and the vehicleside stay using wire ties (2x).
b) Route the TVSS wire harness between the vehicle harness andthe reinforcement .50
491
1546
1
Figure 40
Figure 41
Figure 42
TOP SIDE VIEW
48
47
48
46
49 50
47
48
H
H
1
15
15
1 G
Corolla (RHD) - 26
Corolla (E12-A) TVSS V
04-02
19.
Attach the TVSS wire harness to thevehicle harness using wire ties (4x).16
1
20.
Attach the TVSS wire harness to thevehicle harness using wire ties (2x).16
1
21.
Locate and disconnect the 10P connector(white) in the passenger’s side kick pa-
nel area.52
Figure 43
Figure 44
Figure 45
Route the TVSS wire harness intothe vehicle harness holder .51
1
NOTE:
51
16
1
47
16
147
52
Corolla (RHD) - 27
Corolla (E12-A) TVSS V
04-02
22.
a) Connect the 10P female connector (white) of the TVSS wire harness tothe passenger’s side connector block.
b) Connect the 10P male connector (white) of the TVSS wire harness tothe vehicle harness 10P connector (white).
521
J
1
J
23.
Attach the TVSS wire harness to thevehicle harness using wire ties (3x).16
1
Figure 46
Figure 47
1
1
J
J
52
16
Corolla (RHD) - 2804-02
Corolla (E12-A) TVSS V
2.
a) Connect the 12P female connector (blue) of the TVSS wire harness tothe driver’s side connector block.
b) Connect the 12P male connector (blue) of the TVSS wire harness tothe vehicle harness 12P connector (blue).
421
A
1
A
1.
Locate and disconnect the 12P connector(blue) in the driver’s side kick panel
area.42
Figure 48
Figure 49
3.
Attach the TVSS wire harness to thevehicle harness using wire ties (4x).16
1
Figure 50
WIRE HARNESS INSTALLATION (FOR AUTO AIR CONDITIONER)
42
42
A1
1
16
16
Corolla (RHD) - 29
Corolla (E12-A) TVSS V
04-02
4.
a) Route and attach the TVSS wire har-ness to the vehicle harness using awire tie (1x).
b) Locate the 40P connector (white),then remove the tape from the 40Pconnector .53
5316
1
5.
a) Turn the 40P connector so that thewires faces you and the tab is at theunderside of the connector.
b) By using a small flat-tip screwdriver liftthe lock .A
53
6.
Insert the yellow wired pin of the TVSSwire harness into the designated posi-tion of connector .53
1
D
Figure 51
Figure 52
Figure 53
Lift the lock carefully.ANOTE:
53
16
1
BC
DE
53
D
531
WIRE SIDE VIEW
A
Corolla (RHD) - 30
Corolla (E12-A) TVSS V
04-02
7.
a) Insert the blue/white wired pin ofthe TVSS wire harness into the de-signated position of connector .
b) Insert the blue/yellow wired pin ofthe TVSS wire harness into the de-signated position of connector .53
1
C
53
1
B
8.
a) Insert the green wired pin of theTVSS wire harness into the desig-nated position of connector .
b) Press the lock .A53
1
E
9.
Locate and disconnect the 4P female connector(white) from the passenger's side J/B .
(Go to STEP 10.)4754
Figure 54
Figure 55
Figure 56
If the 4P female connector (white) isnot available, go to STEP 11.
54
NOTE:
WIRE SIDE VIEW
WIRE SIDE VIEW
BOTTOM SIDE VIEW
TOP SIDE VIEW
BC
C
53
53
47
54
4754
53
B
E
1
1
A
Corolla (RHD) - 31
Corolla (E12-A) TVSS V
04-02
10.
a) Attach the foam tape (1x) to thevehicle side stay as shown.
b) Connect the 4P female connector (white) of the TVSS wire harness tothe passenger’s side J/B .
c) Connect the 4P male connector (white) of the TVSS wire harness tothe vehicle harness 4P connector (white).
542
G
472
G
4614
11.
Secure the 4P male connector of theTVSS wire harness to the TVSS wireharness using a wire tie (1x).16
2
G
12.
a) Attach the foam tape (1x) to thevehicle side stay as shown.
b) Connect the 4P female connector (white) of the TVSS wire harness tothe passenger’s side J/B .47
2
G
4614
Figure 57
Figure 58
Figure 59
G
G
F
G
37
54
46
14
2
16
2
G
G
F47
14
216
46
Corolla (RHD) - 3204-02
Corolla (E12-A) TVSS V
2.
a) Insert the flat-blade screwdriver inthe hole.
b) Move down the template until ittouches the radar sensor .
c) Find the number "1" at the centre ofthe notch in the template .If it is not found, rotate the template
and adjust to find the number "1".IV
IV
II
IV
60
1.
a) Locate the trimmer in the smallhole.
b) Turn the trimmer counterclockwiseto the minimum position.
c) Stick the flat-blade screwdriver through the template , and thenadjust to "Good" position.
IV
60
a
a
Figure 60
Figure 61
3.
Turn the trimmer clockwise between thefourth and fifth position from minimum.
a
4
5
45
Figure 62
MOUNTING THE RADAR SENSOR
Use a flat-blade screwdriver with amaximum width of 2mm.
60
CAUTION:
60
60
60
60
I
II
IV
II
IV
a
Good
No Good
a
Corolla (RHD) - 33
Corolla (E12-A) TVSS V
04-02
4.
Measure and attach the aluminum tape on the radar sensor .II
III
5.
Fit the radar sensor to the radar sensorbracket using screws (2x) and nuts
(2x).12
114
II
6.
Cut the foam tape in half.13
Figure 63
Figure 64
Figure 65
Cover the hole of the radar sensorwith aluminum tape .If this is not properly done, the radarsensor sensitivity will not be cor-rect.
II
III
II
CAUTION:
Be sure to tighten the screws firmly.These screws are coated with anadhesive.
11
11
CAUTION:
II
II
III
10,5mm
19mm
57,5mm
57,5mm
12
11
13
4
Corolla (RHD) - 34
Corolla (E12-A) TVSS V
04-02
7.
Attach the foam tape (2x) to the radarsensor bracket and radar sensor .II3
13
8.
Locate and remove the bolt in the glovecompartment area.
61
9.
a) Route the 4P connector of the TVSSwire harness between the heater unit
and vehicle wire .b) Connect the 4P connector of the radar
sensor to the 4P connector (white) of the TVSS wire harness .
c) Wrap the 4P connector into foam tape(1x).
d) Place the radar sensor into the rightside of the glove compartment area.
II
14
1
GII
62631
G
Figure 66
Figure 67
Figure 68
Do not discard the bolt .61
NOTE:
FOR MANUAL A/C MODELS
FOR MANUAL A/C MODELS
II4
13
61
G
14
62
63
II
1
Corolla (RHD) - 35
Corolla (E12-A) TVSS V
04-02
Figure 71
10.
a) Fit the radar sensor using the exis-ting bolt .
b) Secure the 4P connector to the vehicleharness using a wire tie (1x).15
61II
11.
Locate and remove the bolt in the glovecompartment area.
61
12.
a) Route the 4P connector of the TVSSwire harness between the heater unit
and vehicle harness .b) Connect the 4P connector of the radar
sensor to the 4P connector (white) of the TVSS wire harness .
c) Wrap the 4P connector into foam tape(1x).
d) Place the radar sensor into the rightside of the glove compartment area.
II
14
1
GII
64631
G
Figure 69
Figure 70
Do not discard the bolt .61
NOTE:
FOR MANUAL A/C MODELS
FOR AUTO A/C MODELS
FOR AUTO A/C MODELS
Do not pinch the vehicle wire andvehicle harness in between theheater unit and the radar sensorbracket .4
6364
62
CAUTION:
62
63
64
61
4
15
2
F
F
61
14
2
6463
II
Corolla (RHD) - 36
Corolla (E12-A) TVSS V
04-02
13.
a) Fit the radar sensor using the exis-ting bolt .
b) Secure the 4P connector to the vehicleharness using the wire tie (1x).
c) Attach the TVSS wire harness andradar sensor wire harness to the vehi-cle harness using a wire tie (1x).15
2
15
61II
Figure 72
FOR AUTO A/C MODELS
Do not pinch the vehicle harness inbetween the heater unit and theradar sensor bracket .4
6364
CAUTION:
2
1515
II46463
61
Corolla (RHD) - 37
Corolla (E12-A) TVSS V
04-02
2.
Attach the TVSS ECU to the reinforce-ment using a screw (1x).970
I
1.
Fit the bracket to the TVSS ECU .I3
Figure 73
Figure 74
3.
a) Connect the 40P connector (white)of the TVSS wire harness to theTVSS ECU .
b) Attach the TVSS wire harness tothe vehicle harness using a wire tie (1x).
16
1
I
1
D
Figure 75
MOUNTING THE TVSS ECU
FOR MANUAL A/C MODELS
FOR MANUAL A/C MODELS
I
I
3
1
1
16
9
D
70
I
D
Corolla (RHD) - 38
Corolla (E12-A) TVSS V
04-02
4.
Attach the TVSS ECU to the reinforce-ment using a screw (1x).970
I
5.
a) Connect the 40P connector (white)of the vehicle harness to the TVSSECU .
b) Secure the TVSS wire harness tothe vehicle harness using a wire tie (1x).
c) Attach the TVSS wire harness tothe vehicle harness using a wire tie (1x).
16
1
16
1
I
53
Figure 76
Figure 77
FOR AUTO A/C MODELS
FOR AUTO A/C MODELS
70
I
I
9
16
53
1
Corolla (RHD) - 39
Corolla (E12-A) TVSS V
04-02
2.
Locate the 3P connector (black) in thedriver’s side luggage compartment area,then remove the tape.
80
1.
a) Fit the siren bracket to the siren using bolts (2x) and nuts (2x).
b) Screw the nut (1x) lightly as shown.10
iiiii
i7
Figure 78
Figure 79
3.
a) Connect the 3P connector (black) ofthe vehicle harness to the siren .
b) Attach the siren bracket using nuts(2x) as shown.10
7
i
80
Figure 80
MOUNTING THE SIREN
iii
iii
ii
i
10 7
80
80
i
7
10
Corolla (RHD) - 4004-02
Corolla (E12-A) TVSS V
2.
a) Fit the hood switch bracket using abolt (1x).
b) Fit the hood switch to the hoodswitch bracket .
c) Connect the 2P connector (white) ofthe vehicle harness to the hood switch
.d) Attach the 2P connector of the vehicle
harness to the vehicle harness using awire ties (1x).15
5
906
5
8
6
1.
a) Locate the 2P connector (white) inthe engine compartment area, thenremove the tape.
b) Remove the cap .91
90
Figure 81
Figure 82
MOUNTING THE HOOD SWITCH
Using the upper hole of the hoodswitch bracket .6
NOTE:
91
90
90
5
6
8
15
Corolla (RHD) - 41
Corolla (E12-A) TVSS V
04-02
2.
Connect the 1P female connector(white) to the 1P male connector (white).97
96
1.
Remove the luggage lamp in the pas-senger’s side luggage compartment area.
: Clip (4x)
95
Figure 83
Figure 84
CONNECTION OF THE CONNECTOR
95
97
96
95
Corolla (RHD) - 4204-02
Corolla (E12-A) TVSS V
1.
a) Clean the inside surface of both frontwindows.
b) Attach the stickers to both frontdoor windows as shown.
20
Figure 85
ATTACHING THE STICKERS
REFIT THE TRIM AND REMOVED PARTS.
20
5mm
TOYOTA MOTOR CORPORATION