tools technical datasheets bridge saw blades · tools technical datasheets feed speed quality feed...
TRANSCRIPT
Bridge Saw Blades Area of influence: North America
Recommended tools
What are the recommended parameters?
Requirements of my machine
Feed Speed
Quality Quality
Tools Technical Datasheets
Dongsin KCBL+KCBL-FLAvailable in 14"-16"-18"
Diameter of the blade (inches) 14 16 18
2400 - 2200 * 1900 - 1500 * 1500 - 1200 *Rotation speed (rpm)
*Follow the recommendations of every manufacturer
*This feed speed is under optimal conditions of work.
White RestThickness of the slab
20 * 40 *Feed speed (inches/min)
10 25Speed at the exit (inches/min)
2-3 2-3Plunge speed (inches/min)
10 * 20 *Speed cutting 45º (inches/min)
Cooling water flowfocused on the cutting area
Sharpen frequentlythe diamond
Use large flange
Well-leveledbed support
Support of largerdimension of the slab
Blade depth 1/8 inch to3/16 inch on the cutting bed
Konig DIAREX UCSAvailable in 14"-16"-18"
Feed Speed
Quality
Italdiamant EVOGRESAvailable in 12"-14"-16"
Feed Speed
Quality
Terminator nanocut DK3Available in 14"-16"-18"
Feed Speed
Tenax DEKTONAvailable in 14" and 16"
Feed Speed
Quality
Diatex DEKCUTAvailable in 14", 16" and 18"
Feed Speed
Quality
Alpha SILENCER IIIAvailable in 12", 14", 16" and 18"
Feed Speed
Quality
REV.01-01/2019
HighQualityMaximum feed speed
Medium Poor
80"/min 40"/min 20"/min
Where can I get these tools?
The diamond grits on the edge of the blade tend to wear down and glaze over when you are cutting hard materials. Sharpening the blade requires making a slurry out of an abrasive material. The following dressing stones are recommended for that purpose:
Italdiamant/ Koing/ AlphaA) By the authorized dealer in your areaB) www.granquarzt.com
TerminatorA) By the authorized dealer in your areaB) www.terminatordia.comC) www.braxton-bragg.com
TenaxA) By the authorized dealer in your areaB) www.braxton-bragg.com
DiatexA) By the authorized dealer in your areaB) http://usa.diatex.eu
C) www.grandquartz.com
DongsinA) By the authorized dealer in your areaB) www.diaflx.com/index.htm
Should I sharpen the blades?
www.Braxton-Bragg.com www.GrandQuartz.com
Sharpen dry Low RPMGet wet the stone
Adhesive Area of influence: North America
What are the recommended parameters?
Requirements of my machine
Where can I get these tools?
Tools Technical Datasheets
Initial waste (inch) 2-430-150Drying time (minimum) **
Apply with a gun anddisposable mouthpiece
The pieces must bepreviously clean and dry
TenaxA) By the authorized dealer in your area
(www.granquarzt.com)
Integra adhesivesA) By the authorized dealer in your area
B) Sales contact: [email protected]
AkemiA) Web contact:www.braxton-bragg.com B) Web contact: www.granquarzt.com
Slots in the edges toimprove adhesion
HighQualityDrying Time
Medium Poor
30 min 90 min 150 min
Indoors adhesives
Outdoors adhesives
Tenax MASTIDEK(Indoors)
Drying time
Quality
Integra SURFACE BONDER ULTRA(Indoors)
Quality
Drying time
Tenax MASTIDEK(Outdoors)
Feed Speed
Quality
Integra SURFACE BONDER ULTRA(Outdoors)
Quality
Feed Speed
Akemi COLORBOND
Quality
Drying time
Akemi PLATINUM
Quality
Drying time
Akepox 5010
Quality
Drying time
REV.01-01/2019
Area of influence: North America
Recommended Blades
Manual cutter Blades Tools Technical Datasheets
Feed Speed
Quality
Feed Speed
Quality
Feed Speed
Quality
Terminator NANOCUT DKAvailable in 4,5”, 5”, 6” and 7”
Weha R-MESH TURBO BLADEAvailable in 4,5”, 5” and 7”
Pearl P4Available in 4”, 4’5”, 5”,6” ,7”, 10” and 14”
ADW SLIMAvailable in 4,5” and 5”
Feed Speed
Quality
Feed Speed
Quality
Feed Speed
Quality
Feed Speed
Quality
Cyclone MESH THINAvailable in 4”,4,5”,5”,10” and 14”
Apha KATANAAvailable in 4”, 4,5”and 5”
Italdiamant EVOGRESAvailable in 5”
What are the recommended parameters?
Diameter of the blade (inches)
Rotation speed* (rpm)
7”5”4.5”11000-12000 11000-1200011000-12000
*The feed speed should be adjusted according to the type of machine and the thickness of the material. Larger thickness willrequire reduce the feed speed
Requirements of my machine
Water flow focused on the cutting area
Support of largerdimension of the slab
Well-leveledbed support
Sharpen every 4holes drilled
Where can I get these tools?
Alpha/ Cyclone/ PearlA) By the authorized dealer in your area
WehaA) By the authorized dealer in your area
TerminatorA) By the authorized dealer in your areaB) www.Terminatordia.com B) www.grandquartz.com
HighQualityMaximum feed speed
Medium Poor
Fast Medium Slow
Blade depth 1/8 inch to3/16 inch on the cutting bed
REV.01-01/2019
Area of influence: North America
Recommended tools
Drill Bits Tools Technical Datasheets
Feed Speed
Quality
Feed Speed
Quality
Feed Speed
Quality
Feed Speed
Quality
Terminator NANOCUT.DKAvailable in ¼”, 5/16”, 3/8”, ¾”, 1”,
1-1/4”, 1-3/8”, 1-1/2”, 1-3/4”and 2”
Weha WERAMIC CNC BITAvailable in 1”, 1-1/4”, 1-3/8”, 1-1/2”,
2”, 2-1/2” and 3”
ADIAvailable in 3/8”, ¾”, 1”, 1-3/4”, 1-
1/2”, 1-3/4”and 2”
Cyclone Wet Core BitAvailable in either a T-segment
style (1-1 ¾”) or segmented style(2” -5”)
Feed Speed
Quality
Feed Speed
Quality
Feed Speed
Quality
Feed Speed
Quality
ADWAvailable in 5/16”, 25/64”, 5/8”,
25/32”, 3/16”and 5/32”
AppexAvailable in 1/4", 3/8", 1/2",
5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4", 1-3/8", 1-1/2", 1-5/8", 1-3/4", 1-7/8", 2", 2-1/4", 2-
1/2", 2-3/4", 3", 3-1/2", and 4
ProSeriesAvailable in 3/8”, ¾”, 1”, 1-3/4”, 1-
1/2”, 1-3/4”and 2”
Diamut DEKTONAvailable in 1-3/8”
What are the recommended parameters?
Rotation Speed (rpm) 4500*
*This rotation speed will depend on the manufacturer and the diameter of the toolThe working parameters should be recommended mainly by the tools manufacturer.
Requirements of my machine
Sharpen every 4holes drilled
Water flow focused on the cutting area
Support of largerdimension of the slab
Well-leveledbed support
Where can I get these tools?
ADWA) By the authorized dealer in your area
TerminatorA) By the authorized dealer in your areaB) www.diaflx.com/index.htm
HighQualityMaximum feed speed
Medium Poor
Fast Medium Slow
REV.01-01/2019
HighQualityMaximum feed speed
Medium Poor
10 inch/min 8 inch/min 6 inch/min
Finger bits Area of influence: North America
Recommended bits
What are the recommended parameters?
Requirements of my machine
Where can I get these tools?
Tools Technical Datasheets
Italdiamant / ADIA) At www.grandquartz.com
B) By the authorized dealer in your area
TerminatorA) By the authorized dealer in your area
B) www.terminatordia.com
DongsinA) By the authorized dealer in your area
Terminator NANOCUT DKAvailable in 8"x12", 8"x16" and 8"x20"
Dongsin M1Available in one size
ADI Seg FOR DEKTONAvailable in one size
Quality
Feed Speed
Quality
Feed Speed
Quality
Feed SpeedFeed Speed
Quality Quality
Feed Speed
Italdiaman EVOGRESAvailable in one size
Thickness of the slab 8mm 12mm 20mm
4500 4500 4500Rotation speed (rpm)6000 - 7500* 6000 - 7500* 6000 - 7500*Rotation speed
milling tool (rpm)
8 mm 12 mm 20 mmThickness of the slab
8 7,5 7Feed speed (inches/min)3 3 3Speed at exit (inches/min)
Cooling water flowfocused on thecutting area
Well-leveled bed support
Sharpen the toolbefore each real job
Support of largerdimension of the slab
Diamut DEKTON BITAvailable in one size
*Follow the recommendations of every manufacturer
REV.01-03/2019